Experimental Study on the Mechanism and Effect of Middle-Phase Microemulsion Flooding in a Conglomerate Reservoir Authors: Hongzhi Shao, Tongjing Liu, Dan Guan, Jiangfei Sun, Wenjie Tang, Zirui Zhao, Huoxin Luan, Patiguli Maimaiti, Jiahao Zhan, Baokang Ren Published: 2026 ABSTRACT To address the characteristics of strong heterogeneity, complex pore-throat structures, and poor adaptability of conventional flooding systems in conglomerate reservoirs, a systematic comparative study on the oil displacement efficiency of middle-phase microemulsion and conventional binary systems (polymer + surfactant) was conducted using a combination of long-core displacement experiments, interfacial tension measurements, and polarizing microscopy observations. Representative cores with permeability ranging from 50 to 500 mD were selected for displacement experiments under varying conditions of injection rate, permeability contrast, timing of chemical injection, and surfactant concentration. A three-stage experimental procedure comprising waterflooding, chemical flooding, and post-waterflooding was employed to compare and analyze the injectivity, enhanced oil recovery (EOR) magnitude, and water control performance of the two flooding systems. The results indicate that the middle-phase microemulsion exhibits significantly superior oil displacement efficiency compared to the binary system across the entire permeability range. It demonstrates excellent injectivity in medium-permeability reservoirs above 50 mD, rapidly achieving an ultra-low interfacial tension on the order of 10–3 mN/m, which effectively mobilizes residual oil trapped in fine pore throats. The final enhanced oil recovery increment is 3–7 percentage points higher than that achieved with the binary system. The applicability boundaries for middle-phase microemulsion flooding are defined as follows: permeability should not be lower than that of conventional low-permeability reservoirs; injection conversion is preferably implemented during the high water-cut stage; the permeability heterogeneity ratio should not exceed 10. Additionally, supporting measures for channeling control are required to accommodate reservoir stress sensitivity. The middle-phase microemulsion effectively inhibits water channeling, and its stability and profile control capability are significantly superior to those of the binary system. The research findings provide technical support and a theoretical basis for enhanced oil recovery in conglomerate reservoirs and analogous highly heterogeneous reservoirs. Introduction As one of the globally significant reservoir types, conglomerate reservoirs occupy a pivotal position in worldwide oil and gas development due to their large reserves, broad distribution, and high potential for per-well productivity. Conglomerate reservoirs in the Xinjiang region represent a core resource for oilfield development in western China, with proven geological reserves exceeding 100 million tons, which underscores their substantial development value. However, the development of the Xinjiang conglomerate reservoirs faces unprecedented technical challenges. This reservoir type exhibits extremely complex geological characteristics, with an average porosity ranging from 10% to 20%, permeability spanning 0.01 to 817 mD, and generally poor physical properties. More critically, conglomerate reservoirs display pronounced heterogeneity, with permeability contrasts reaching up to 70-fold. During waterflooding, they are highly susceptible to the formation of channeling pathways, leading to inefficient or ineffective circulation of displacing fluids, thereby constraining the effective sweep volume. The waterflood recovery factor is merely 30–40%, leaving substantial volumes of crude oil trapped within low-permeability matrices and fine pore throats. As oilfield development progresses, this reservoir type has widely entered the high-water-cut stage, with water cut exceeding 90% in some blocks, and the remaining oil becoming increasingly fragmented. Conventional waterflooding is no longer sufficient to meet the demands of reserve potential tapping, positioning chemical flooding as an effective strategy to enhance oil recovery from such reservoirs. − Binary polymer–surfactant flooding represents the most mature and widely deployed chemical EOR technology at present, relying on the synergistic effect of polymers to adjust oil–water mobility ratios and surfactants to lower interfacial tension (IFT). − This technology performs well in reservoirs with mild heterogeneity, and abundant studies have optimized its formulation and matching performance for various oil-bearing formations. Researchers have improved binary systems to mitigate formation damage while preserving interfacial activity and mobility control, − modified postpolymer flooding active polymers to broaden applicable scenarios, and clarified the displacement potential of high-emulsification formulas for heavy crude oil. Further quantitative research has revealed the matching law between the hydrodynamic size of binary agents and reservoir pore throats, offering guidance for parameter design. Nevertheless, conventional binary flooding suffers critical drawbacks when deployed in Xinjiang conglomerate reservoirs with strong heterogeneity and moderate to high salinity: poor in situ stability and massive surfactant adsorption loss drastically weaken its EOR capacity, restricting field promotion in such formations. Middle-phase microemulsion has gradually become a cutting-edge alternative EOR agent to overcome the limitations of binary systems, owing to its intrinsic merits of ultra-low IFT, superior salt tolerance, antiadsorption capacity, and stable emulsification, which endow it with outstanding transport and oil-stripping performance in intricate multiscale pore networks. Existing fundamental studies have laid a basic theoretical framework for middle-phase microemulsion flooding: prior work optimized agent formulas and analyzed the influence of component ratios on displacement performance, − standardized characterization methods and evaluation criteria for microemulsion phase behavior, , screened formulas targeting low-permeability formations, systematically elaborated its microscopic oil-displacement mechanisms, verified the adaptability of petroleum sulfonate microemulsions under high-salinity conditions, , and quantified how heterogeneous reservoir properties alter recovery efficiency. − Despite the above advances, critical knowledge gaps remain for the development of conglomerate reservoirs. Few investigations have systematically quantified how core engineering parameters, such as injection rate, permeability contrast, and chemical-flood switching water cut, regulate the macro- and microdisplacement behaviors of middle-phase microemulsions under the unique geological conditions of conglomerate deposits. Without clear quantitative correlations between these operating variables and EOR outcomes, field engineers lack targeted, actionable parameter optimization schemes for on-site microemulsion injection, which seriously restricts the industrial application of this promising technology in conglomerate oil fields. Aiming at the severe heterogeneity and complex multiscale pore-throat structure of conglomerate reservoirs, this work establishes a multivariable experimental framework via reservoir-simulated long-core displacement tests. We systematically compare the EOR performance of the commercial middle-phase microemulsion system and the conventional polymer–surfactant binary system, quantify their performance gaps, and clarify the applicable engineering parameter window of the microemulsion agent. This work delivers a theoretical basis and technical guidance for EOR implementation in conglomerate and other strongly heterogeneous reservoirs. Experimental Section Experimental Materials Experimental water samples were collected on site from a conglomerate oil reservoir in Xinjiang. After extraction via siphoning and precision filtration, residual oil droplets and suspended solids were removed to obtain clean simulated formation water with an ionic composition highly similar to that of the original formation water. Its main ionic composition and salinity are shown in Table . 1Main Ionic Composition of the Simulated Injected WaterIonic compositionHCO3 – Cl– SO4 2– Ca2+ Mg2+ K+, Na+ Total salinityIonic content(mg/L)2477.837027.4895.6334.2126.755449.315111.2 Main Ionic Composition of the Simulated Injected Water According to the sampling and analysis results of the field oil well, the formation water of the test well is NaHCO3 type with a pH of 7.65, a surface tension of 70.4 mN/m, a salinity of 15111.2 mg/L, indicating moderately high salinity, and a density of 1.0094 g/cm3. All water samples were filtered through a 0.25 μm microporous membrane before use to eliminate suspended particles and residual crude oil droplets and avoid interference with the phase behavior of the microemulsion. The experimental oil is a simulated oil, which is prepared by mixing dehydrated crude oil sampled from the Xinjiang conglomerate oil reservoir with neutral kerosene at a mass ratio of 3.5:1. At a reservoir temperature of 28 °C, its viscosity was measured to be 16.4 mPa·s, which is consistent with the physical properties of real crude oil. Considering the influence of price factors, representative surfactants with mature production processes and low purchase prices were selected for the study. The density of crude oil is 0.842 g/cm3, the acid value is 0.21 mg KOH/g, the wax content is 4.3 wt %, and the total content of resin and asphaltene is 8.7 wt %. Crude oil was dehydrated at 60 °C for 48 h to remove free water. Among them, the middle-phase microemulsion system uses treated reinjection water from the polymer injection station as the solvent, compounded with 0.5% surfactant and 0.15% salt-resistant polymer (KY-ZSP), and stands for 24 h after dilution to stabilize the phase state. The binary system uses treated reinjection water from the polymer injection station as the solvent, compounded with 0.3% surfactant and 0.15% salt-resistant polymer (KY-ZSP), and stands for 24 h after dilution to stabilize the phase state. After standing for 24 h, the fully mixed solution was sealed and stored at 28 °C for 72 h for stability observation. No demulsification, oil-water stratification, precipitation, or particle agglomeration were observed by naked eyes, which confirmed the long-term stability of the prepared medium-phase microemulsion bulk system. Standard binary formula for multifactor variable experiments (permeability, injection rate, permeability contrast, switching timing): 0.3 wt % surfactant+0.15 wt % KY-ZSP antisalt polymer, consistent with the conventional field injection formula for horizontal comparison. Binary control group for the surfactant concentration gradient test: To realize fair parallel comparison with 0.3/0.4/0.5 wt % middle-phase microemulsion groups, we set the maximum surfactant dosage of the binary reference group to 0.5 wt %, while keeping the polymer concentration fixed at 0.15 wt %. The experimental cores were taken from the Xinjiang conglomerate oil reservoir, with a permeability of 50–500 mD, lengths of 30 and 60 cm, and a diameter of 2.5 cm. After cleaning and drying, the cores were saturated with simulated formation water by the vacuum saturation method to establish irreducible water saturation. Then, the simulated crude oil was saturated by stepwise displacement to form initial oil saturation, and the cores were ready for use after pretreatment. The basic parameters of the cores are shown in Table . 2Basic Physical Parameters of the Experimental Conglomerate Cores Core IDGas permeability /(mD)Pore volume/(cm3)Porosity/(%)Saturated oil volume/(cm3)Initial oil saturation/(%)Core 147.78723.7018.0116.4369.32Core 2263.20826.8318.0618.9070.44Core 3473.88127.5018.0519.0369.20Core 448.16423.2418.0316.2169.75Core 5268.10727.5618.0719.1269.38Core 6473.36627.5618.0919.1469.45Core 748.67122.7518.0416.4572.31Core 8264.64426.5618.1018.7270.48Core 9485.40428.7518.1019.6468.31Core 1049.89623.7318.0116.8270.88Core 11242.13126.6618.0918.8170.56Core 12469.42728.9818.1119.7568.15aNote: 1 mD =1×10–3 μm2. Basic Physical Parameters of the Experimental Conglomerate Cores Note: 1 mD =1×10–3 μm2. Experimental Equipment A high-temperature and high-pressure physical simulation experimental device is used, and its flow schematic diagram is shown in Figure . The main instruments of this experimental device include thermostat (produced in Hai’an, Jiangsu), EMO-AP-1 high-pressure advection pump (produced in Shanghai Huayue), TX500C rotating interfacial tensiometer (produced by Temco Company, USA), polarizing microscope (produced by Leica, Germany), and a rotational viscometer (produced by Brookfield Company, USA). Schematic diagram of high-temperature, high-pressure long-core physical simulation experimental device. Experimental Content Displacement Experiments A parallel experimental design was adopted. Twenty-six groups of 30 and 60 cm cores were selected to conduct water flooding, middle-phase microemulsion flooding, binary system flooding, and subsequent water flooding experiments, respectively. The reservoir temperature was simulated at 28 °C, and the displacement rate was 0.1–0.2 mL/min. According to the actual field injection and reservoir scheme, a long-core comparative experimental plan was formulated to compare the oil-displacement effects of the two chemical systems. The experimental scheme for middle-phase microemulsion flooding is as follows: first, inject simulated formation water into the core at 0.1 mL/min, record displacement pressure and oil production at the outlet every 10 min until the water cut at the outlet exceeds 98%, stop water flooding, and calculate the water flooding recovery. After water flooding, middle-phase microemulsion was injected into the core with an injection volume of 1 pore volume (PV) at the same displacement rate of 0.1 mL/min. Displacement pressure and oil production were also recorded every 10 min until the water cut at the outlet again exceeded 98%, and then displacement was stopped and microemulsion flooding recovery was calculated. After middle-phase microemulsion flooding, subsequent water flooding was conducted under the same experimental conditions, with an injection volume of 1 pore volume, until the outlet water cut exceeded 98% again. Displacement was stopped, and the subsequent water flooding recovery and total recovery were calculated. The experimental steps at an injection rate of 0.2 mL/min were the same as above. The experimental scheme for binary flooding is as follows: first, inject simulated formation water into the core at 0.1 mL/min, record displacement pressure and oil production at the outlet every 10 min until the water cut at the outlet exceeds 98%, stop water flooding, and calculate the water flooding recovery. After water flooding, the binary system was injected into the core with 1 pore volume at 0.1 mL/min. Displacement pressure and oil production were recorded every 10 min until water cut exceeded 98% again, and then displacement was stopped and the binary flooding recovery was calculated. After binary flooding, subsequent water flooding was carried out under the same conditions with 1 pore volume injected until the water cut exceeded 98% again. Displacement was stopped, and subsequent water flooding recovery and total recovery were calculated. The experimental steps at an injection rate of 0.2 mL/min were the same as those above. Comparative Experimental Design To systematically evaluate the effects of different conditions on oil displacement efficiency, multiple groups of comparative experiments were set up: core flooding experiments of middle-phase microemulsion and binary flooding under different permeability, injection rate, permeability ratio, switching timing, and system concentration were carried out to compare the oil displacement effects of the two systems and evaluate the influence of different parameters on recovery factor. Interfacial Tension Measurement The spinning drop interfacial tensiometer places oil droplets in a centrifugal field. Using the density difference between the two liquids, the balance between gravity and oil-water interfacial tension is artificially changed at a certain rotational speed, so that oil droplets form cylindrical or ellipsoidal shapes in high-density liquid for oil–water interfacial tension measurement. According to SY/T 6424–2014 “Test Method for Performance of Combination Flooding Systems”, the interfacial tension between the system and simulated oil was measured by TX500C spinning-drop interfacial tensiometer at 28 °C and 3000 r/min, and the stable value was taken. The measurement range of this method for oil–water interfacial tension can reach 10–5mN/m. It is worth noting that adjusting the rotating speed of the spinning-drop interfacial tensiometer can change the shape of oil droplets at equilibrium. Seepage Parameter Analysis Based on the data on pressure, flow rate, and water cut recorded during the displacement experiments, the seepage characteristics of the two systems were evaluated, and the differences in oil displacement effects were analyzed. Results and Discussion In the process of long-term core flooding, three control measures were taken to maintain the stability of the system: preheating all intermediate containers and injection pipelines to a constant temperature of 28 °C to avoid phase changes caused by temperature fluctuations; the injection rate should be strictly controlled in the range of 0.1–0.2 mL/min to reduce the shear degradation of surfactant aggregates. The entire injection channel is filled with liquid to isolate air contact and prevent surfactant oxidation demulsification. Effect of Permeability on Oil Displacement Efficiency At an injection rate of 0.2 mL/min, the results of displacement experiments on 30 cm cores with different permeabilities show that the oil displacement effects of middle-phase microemulsion and binary system both show significant differences with the change of permeability, but middle-phase microemulsion exhibits better enhanced oil recovery ability across the entire permeability range, as shown in Table . 3Comparison of Oil Displacement Effects of Two Systems in 30 cm Cores under Different PermeabilitiesCore numberPermeability/(mD)Displacement systemWater flooding recovery efficiency/(%)Total recovery efficiency/(%)Enhanced oil recovery/(%)Core 147.787Middle-phase microemulsion40.7876.0835.30Core 2263.208Middle-phase microemulsion40.1078.3538.25Core 3473.881Middle-phase microemulsion41.5177.2535.74Core 448.164Binary system40.2169.8429.63Core 5268.107Binary system40.7971.6530.86Core 6473.366Binary system40.7574.7133.96 Comparison of Oil Displacement Effects of Two Systems in 30 cm Cores under Different Permeabilities In low-permeability cores with middle-phase microemulsion and binary systems, the total recovery of middle-phase microemulsion reaches 76.08%, 35.30 percentage points higher than water flooding; the total recovery of the binary system is 69.84%, with an increase of 29.63 percentage points. In medium-permeability cores, the total recovery of middle-phase microemulsion flooding is up to 78.35%, 6.7 percentage points higher than the 71.65% of the binary system, showing the most significant oil increment advantage. The core pore-throat connectivity in this permeability range is moderate, and the self-profile control effect and ultra-low interfacial tension oil washing effect of middle-phase microemulsion work synergistically, which can block dominant channels through selective retention and efficiently strip oil films on pore surfaces. Although the binary system can improve the mobility ratio, the reduction of residual oil saturation is only 80% of that of the middle-phase microemulsion. In medium-high permeability cores, the recovery gap between the middle-phase microemulsion and binary system narrows slightly, with the former having a total recovery of 77.25% and the latter 74.31%. However, the water control effect of middle-phase microemulsion is better, and the water cut after flooding drops to 38.46%, 2.4 percentage points lower than that of the binary system. Under high-permeability conditions, the binary system tends to break through quickly along high-permeability channels with limited sweep volume, while the middle-phase microemulsion has strong emulsification stability, which can inhibit fingering and prolong the effective displacement time. Effect of Injection Rate on Oil Displacement The effects of injection rates (0.1 mL/min and 0.2 mL/min) on the oil displacement performance of the two systems exhibit different patterns. When the middle-phase microemulsion is injected at 0.2 mL/min, the recovery enhancement of cores with different permeabilities is higher than that at 0.1 mL/min. The incremental oil recovery of the 250 mD core reaches 38.25 percentage points, which is 15.81 percentage points higher than that at 0.1 mL/min. At a higher injection rate, the middle-phase microemulsion can quickly establish a displacement pressure gradient, reduce adsorption and retention loss, and show a more significant emulsification and solubilization effect. Its recovery enhancement is controlled by the synergistic effect of permeability and injection rate, improving the migration efficiency of the oil droplets. However, when the injection rate is too high (>0.2 mL/min), water channeling easily occurs in low-permeability cores, resulting in a slight decrease in oil recovery, as shown in Table . 4Comparison of Oil Displacement Effects of Two Systems in 30 cm Cores under Different Injection RatesCore numberPermeability/ (mD)Injection rate/ (mL/min)Displacement systemWater flooding recovery efficiency/(%)Total recovery efficiency/(%)Enhanced oil recovery/(%)Core 147.7870.2Middle-phase microemulsion40.7876.0835.30Core 2263.2080.2Middle-phase microemulsion40.1078.3538.25Core 3473.8810.2Middle-phase microemulsion41.5177.2535.74Core 448.1640.2Binary system40.2169.8429.63Core 5268.1070.2Binary system40.7971.6530.86Core 6473.3660.2Binary system40.7574.7133.96Core 748.6710.1Middle-phase microemulsion46.2069.3023.10Core 8264.6440.1Middle-phase microemulsion47.5469.9822.44Core 9485.4040.1Middle-phase microemulsion47.8672.3024.44Core 1049.8960.1Binary system46.3767.7821.41Core 11242.1310.1Binary system47.8568.5820.73Core 12469.4270.1Binary system48.1070.8922.79 Comparison of Oil Displacement Effects of Two Systems in 30 cm Cores under Different Injection Rates Consistent with the middle-phase microemulsion, the binary system also shows a better displacement rule at an injection rate of 0.2 mL/min, but its incremental oil recovery is lower than that of the middle-phase microemulsion, and it is more sensitive to permeability. Core 6 (permeability 473.366 mD) achieves an incremental oil recovery of 33.96 percentage points at 0.2 mL/min, which is 11.17 percentage points higher than that at 0.1 mL/min (core 12, 22.79 percentage points). The incremental oil recovery of medium-permeability Core 5 (268.107 mD) and low-permeability Core 4 (48.164 mD) increases by 10.13 and 8.22 percentage points, respectively, at a high injection rate compared with 0.1 mL/min. It should be noted that the binary system has a lower upper tolerance limit for the injection rate. When the injection rate exceeds 0.2 mL/min, it is easy to cause shear degradation of polymer molecules and aggravated adsorption loss of surfactants, which instead attenuate the oil displacement effect. Further analysis of the rate adaptability of the two systems shows that within the injection rate range of 0.1–0.2 mL/min, the incremental oil recovery of middle-phase microemulsion ranges from 22.44 to 38.25 percentage points, while that of the binary system is 20.73–33.96 percentage points, indicating that middle-phase microemulsion has wider fault tolerance to injection rate. This characteristic is highly consistent with field development, where the actual injection rate is easily affected by reservoir pressure and pipeline transportation conditions. The adaptability of middle-phase microemulsion can reduce the difficulty of on-site process control and is more suitable for large-scale applications. Effect of Permeability Ratio on Oil Displacement Permeability contrast is a core parameter characterizing the heterogeneity of conglomerate reservoirs, which directly affects the migration path, sweep volume, and remaining oil recovery efficiency of displacement systems. Heterogeneous models with different permeability contrasts (1.25, 2, 5) were constructed using 60-cm-long cores to systematically compare the adaptability differences between middle-phase microemulsion and binary system in long-distance displacement, revealing the regulation law of permeability contrast on the oil displacement effect of the two systems, as shown in Table . The selection of 60-cm-long cores is closer to the actual seepage paths in oil fields, which can accurately reflect the heterogeneous response characteristics of the systems during deep migration, making the experimental results more valuable for field guidance. 5Comparison of Oil Displacement Effects of Two Systems in 60 cm Cores under Different Permeability ContrastsCore numberPermeability contrastDisplacement systemWater flooding recovery efficiency/(%)Total recovery efficiency /(%)Enhanced oil recovery/(%)Sweep coefficient/(%)Core 131.25Middle-phase microemulsion41.2376.2334.9982.5Core 141.25Binary system40.8972.1531.2678.3Core 152Middle-phase microemulsion39.6775.2435.5775.1Core 162Binary system39.2168.3229.1162Core 175Middle-phase microemulsion38.4568.4130.0068Core 185Binary system37.9859.2721.2955.7 Comparison of Oil Displacement Effects of Two Systems in 60 cm Cores under Different Permeability Contrasts Experimental results show that the oil displacement effects of both systems decrease with the increase of permeability contrast, but the antiheterogeneity ability of middle-phase microemulsion is significantly better than that of binary system, and its advantage is more prominent in deep displacement of 60-cm-long cores. When the permeability contrast increases from 1.25 to 5, the total oil recovery of middle-phase microemulsion decreases from 76.23% to 68.41%, with a drop of 7.82 percentage points; the total recovery of the binary system decreases from 72.15% to 59.27%, with a drop of 12.88 percentage points, 1.65 times that of middle-phase microemulsion. Overall, the thermodynamic stability of middle-phase microemulsion makes it not easy to demulsify or inactivate in heterogeneous displacement of 60-cm-long cores, and it can form a synergistic effect of dynamic plugging through selective retention, maintaining a certain sweep range even under high permeability contrast. As a physical synergistic system, the profile control and oil washing effects of the binary system depend on the stability of polymer viscosity and surfactant concentration. It is easily affected by adsorption, shearing, and other factors in deep migration of long cores, leading to the attenuation of the synergistic effect and difficulty in adapting to highly heterogeneous environments. Effect of Switching Injection Timing on Oil Displacement Switching injection timing directly determines the contact efficiency between the chemical flooding system and remaining oil, the occupation state of reservoir pore throats, and the development degree of channeling paths and is a key engineering parameter affecting the chemical flooding effect in conglomerate reservoirs. Based on 60-cm-long cores with permeability of 250 mD and injection rate of 0.2 mL/min, two typical switching nodes at waterflood water cut of 80% and 95% were selected to systematically compare the oil displacement differences between middle-phase microemulsion and binary system and clarify the optimal switching timing for both systems, as shown in Table . The long-distance displacement characteristics of 60-cm-long cores can accurately simulate the deep migration and remaining oil mobilization process of the system after field-switching flooding, making the experimental results more instructive for field application. 6Comparison of Oil Displacement Effects of Two Systems in 60 cm Cores under Different Switching Injection TimingsCore numberWater cut/(%)Displacement systemWater flooding recovery efficiency/(%)Total recovery efficiency/(%)Enhanced oil recovery/(%)Minimum water cut after flooding/(%)Core 1980Middle-phase microemulsion37.8188.9352.1241.22Core 2080Binary system38.2582.1543.9045.67Core 2195Middle-phase microemulsion42.5173.6431.1349.04Core 2295Binary system43.1271.8428.7252.33 Comparison of Oil Displacement Effects of Two Systems in 60 cm Cores under Different Switching Injection Timings Experimental results show that both systems exhibit better recovery efficiency with earlier switching injection, that is, the incremental oil recovery when switching at 80% water cut of water flooding is significantly higher than that at 95%, but the middle-phase microemulsion has stronger fault tolerance for switching timing, and its advantages are more prominent at different switching nodes. When the switching timing is delayed from 80% to 95% water cut of water flooding, the incremental oil recovery of middle-phase microemulsion decreases from 51.12 percentage points to 31.13 percentage points, a drop of 19.99 percentage points; that of the binary system decreases from 43.90 percentage points to 28.72 percentage points, a drop of 15.18 percentage points. Under the condition of switching at an 80% water cut of water flooding, the middle-phase microemulsion shows a better oil displacement effect, with water cut reduced to 41.22%, total oil recovery 6.78 percentage points higher than that of the binary system, and the stable production period at low water cut is significantly better than that of the binary system. With stronger antiadsorption and antichanneling abilities, middle-phase microemulsion can achieve better oil displacement effect than binary system at different switching timings and can fully exert its technical potential especially in early switching. Combined with the actual development needs of Xinjiang conglomerate reservoirs, the optimal switching timing of the middle-phase microemulsion is about 80% water cut of water flooding, which can achieve dual optimization of recovery efficiency and economic benefits. The binary system needs earlier switching to make up for its insufficient stability, but its overall oil increment potential is still lower than that of the middle-phase microemulsion. For old blocks that have entered the ultra-high water cut stage, middle-phase microemulsion is still a better choice. The combined scheme of channeling control pretreatment and middle-phase microemulsion flooding can effectively tap into the remaining oil. Effect of System Concentration on Oil Displacement In chemical flooding systems, the system concentration directly determines the interfacial activity and seepage characteristics of the system and is a key parameter affecting the oil displacement effect and economic benefits. To clarify the optimal concentration range of middle-phase microemulsion and binary system, the polymer mass concentration was fixed at 0.15% KY-ZSP salt-resistant polymer, and the water used for preparation was the reinjected water from the polymer injection station. 60-cm-long core flooding comparison experiments were carried out at surfactant concentrations of 0.3%, 0.4%, and 0.5%, respectively, with a permeability of about 250 mD and an injection rate of 0.2 mL/min. The experimental results are shown in Table . 7Comparison of Oil Displacement Effects of Two Systems in 60 cm Cores under Different System ConcentrationsCore numberPermeability/ (mD)Displacement systemSurfactant concentration/(%)Water flooding recovery efficiency/(%)Total recovery efficiency/(%)Enhanced oil recovery/(%)Core 23252.46Middle-phase microemulsion0.340.5274.1633.64Core 24248.71Middle-phase microemulsion0.440.3776.8336.46Core 25263.21Middle-phase microemulsion0.540.1078.3538.25Core 26268.11Binary system0.540.7971.6530.86 Comparison of Oil Displacement Effects of Two Systems in 60 cm Cores under Different System Concentrations Total oil recovery factor: 1 ER=VopVoi×100% Enhanced oil recovery: 2 ΔER=ER(total)−ER(waterflood) Experimental results show that the oil displacement effect of middle-phase microemulsion gradually improves with the increase of surfactant concentration, and its incremental oil recovery is significantly better than that of binary system at all concentrations. When the surfactant concentration increases from 0.3% to 0.4%, the incremental oil recovery of middle-phase microemulsion rises from 33.64% to 36.46%, an increase of 2.82 percentage points. When the concentration continues to increase to 0.5%, the incremental oil recovery further rises to 38.25%, which is 4.61 percentage points higher than that at 0.3% concentration. This is because with the increase of surfactant concentration, the system is easier to form a stable middle-phase structure, the oil-water interfacial tension can quickly reach an ultra-low level of 10–3 mN/m, the emulsification and solubilization ability is stronger, and the remaining oil in fine pore throats can be stripped more fully. In comparison, the incremental oil recovery of binary system at 0.5% surfactant concentration is only 30.86%, which is significantly lower than that of middle-phase microemulsion at all concentrations, indicating that middle-phase microemulsion can achieve better oil displacement effect with lower chemical dosage. Considering the oil displacement effect and economy comprehensively, the middle-phase microemulsion system with 0.5% surfactant concentration has the best oil enhancement effect, which is more suitable for field application of enhanced oil recovery in Xinjiang conglomerate reservoirs. Analysis of Interfacial Tension and Stability Interfacial tension test results show that middle-phase microemulsion reduces interfacial tension faster and has stronger stability. The interfacial tension between middle-phase microemulsion and formation-simulated oil can reach an ultra-low level of 10–3 mN/m within 15 min and stabilizes at 0.008782 mN/m after 60 min. The binary system takes 45 min to drop to 10–2 mN/m and reaches 0.015088 mN/m at 60 min, which is 1.875 times that of the middle-phase microemulsion. Ultra-low interfacial tension enables middle-phase microemulsion to effectively strip remaining oil in pores, as shown in Table . 8Determination of Interfacial Tension Interfacial tension value /(mN/m)Testing instrumentTesting time/minBinary systemMiddle-phase systemTX500C10.2617430.014966TX500C150.2653760.009503TX500C300.1861630.009153TX500C450.0266490.008967TX500C600.0150880.008782 Determination of Interfacial Tension Polarizing microscope observations show that compared with conventional binary flooding, the transition zone in the produced fluid from middle-phase microemulsion system flooding has a lower height and the emulsion is finer. The middle-phase microemulsion is uniform and transparent before flooding, with particle sizes concentrated at 50–100 nm. During middle-phase microemulsion flooding, there is no obvious agglomeration of particles in conglomerate pore throats, and stable dispersion is maintained. The particle size remains at 50–100 nm with no agglomeration or demulsification, which is highly compatible with the size of conglomerate pore throats, as shown in Figures –. The emulsion particle size of the produced fluid after binary system flooding is uneven, and demulsification and stratification occur in some parts, with stability weaker than that of the middle-phase microemulsion. This is because the thermodynamically stable structure of the middle-phase microemulsion makes it difficult to deactivate during migration and provides more durable oil displacement efficiency. This is the core microscopic mechanism for its higher oil recovery rate than the binary system. Polarizing microscope image after binary flooding. Polarizing microscope image after middle-phase microemulsion flooding. Analysis of Seepage Characteristics To compare the seepage characteristics of the middle-phase microemulsion and binary system in conglomerate reservoirs, the apparent resistance coefficient and apparent residual resistance coefficient were calculated based on long-core flooding experimental data; the mobility control ability and pore retention effect of the systems were quantitatively evaluated, and the seepage differences and adaptability of the two systems were clarified. The results are shown in Table . 9Apparent Resistance Coefficients and Apparent Residual Resistance Coefficients of Two Systems in 60 cm CoresCore numberPermeability/ (10–3 μm2)Flooding systemApparent resistance coefficientApparent residual resistance coefficientCore 2750.77Middle-phase system1.870.37Core 28263.87Middle-phase system1.610.56Core 29512.98Middle-phase system1.540.52Core 3048.83Binary system1.600.50Core 31248.31Binary system2.470.37Core 32491.20Binary system1.460.60 Apparent Resistance Coefficients and Apparent Residual Resistance Coefficients of Two Systems in 60 cm Cores The apparent resistance coefficient reflects the flow resistance and mobility control ability of the flooding system in cores, and a higher value indicates stronger viscosity enhancement, emulsification, or pore plugging effect of the system. Experimental data show that the apparent resistance coefficient of the middle-phase microemulsion first decreases and then stabilizes with an increase in permeability. The apparent resistance coefficient of the binary system shows the characteristics of being the highest in medium permeability, followed by low permeability and the lowest in high permeability. Overall, the middle-phase microemulsion has a stronger mobility control ability in medium-permeability reservoirs, while the binary system shows a higher apparent resistance coefficient in medium-permeability reservoirs. The apparent residual resistance coefficient reflects the degree of permeability change after the system is adsorbed and retained on the pore surface and is a key index for evaluating the retention ability and long-term control effect of the system. Experimental data show that the apparent residual resistance coefficients of the two systems fall between 0.37 and 0.60. This belongs to the normal range of permeability reduction and pore retention after chemical flooding, further verifying the reliability of the experimental data. Overall, under medium permeability conditions, the middle-phase microemulsion has good matching with rock pore throats, and the effects of adsorption retention and emulsification plugging of the system are stronger; therefore, the apparent residual resistance is higher. The apparent residual resistance coefficient of the binary system increases gradually with the increase in permeability. The comparison shows that the middle-phase microemulsion has stronger flow resistance in low-permeability reservoirs and stronger retention effect in medium-permeability reservoirs, which is suitable for strongly heterogeneous conglomerate reservoirs in Xinjiang with permeability of 50–300 mD. Under the experimental conditions in this paper, compared with the strong heterogeneous conglomerate model used in this study, the binary system shows more matching mobility control performance in the relatively homogeneous high-permeability core. Conclusions In this study, through 30- and 60-cm-long core flooding experiments, the oil displacement effects of middle-phase microemulsion and binary systems under the conditions of Xinjiang conglomerate reservoirs were compared, and the engineering application limits of middle-phase microemulsion in such reservoirs were clarified. The main conclusions drawn from this study are as follows: (1) The middle-phase microemulsion shows significantly better oil displacement effect than the binary system in the full permeability range. The existing middle-phase microemulsion system is suitable for medium-permeability reservoirs and can produce residual oil in finer pore throats. This advantage is mainly attributed to the fact that the middle-phase microemulsion can quickly form ultra-low interfacial tension of 10–3 mN/m in a short time and has excellent emulsification stability and anti-adsorption ability. (2) The middle-phase microemulsion system has good adaptability under different injection conditions. When the injection rate is 0.2 mL/min, the enhancement of the oil recovery of cores with different permeabilities reaches the highest. The enhanced oil recovery of medium-permeability cores reaches 38.25 percentage points, which is 15.81 percentage points higher than that at 0.1 mL/min, and it can adapt to strongly heterogeneous reservoirs with a permeability ratio up to 5. When the permeability ratio increases from 1.25 to 5, its total oil recovery only decreases by 7.82 percentage points, while that of the binary system decreases by 12.88 percentage points. In terms of switching injection timing, the middle-phase microemulsion has the best effect when switching injection at an 80% water cut. (3) The basic applicable limits of the middle-phase microemulsion flooding system in conglomerate reservoirs are clarified as follows: permeability not lower than conventional low permeability, preferred injection switching in the high water cut stage, and permeability ratio not higher than 10. In view of the obvious stress sensitivity characteristics of reservoirs, channeling control is recommended for field tests. (4) This study provides important technical support for the efficient development of Xinjiang conglomerate reservoirs and similar strongly heterogeneous oil reservoirs. In the future, field test research of middle-phase microemulsions under actual reservoir conditions will be further carried out, the supporting technical system will be improved, and the industrial application of this technology will be promoted.