Design- and Voxel-Based Analysis of a Topology–Density Dual-Gradient TPMS Absorber for Impact-Load Mitigation Authors: Wenying Xu, Jiawei Xu, Yonglin Chen, Dongyu Fan, Yongbin Wang, Tao Yu, Siyu Chen, Weidong Yang Published: 2026 ABSTRACT HighlightsA 0.33 mm C3D8R voxel model achieved 1.11% density error and reduced runtime by 88%.IWP20 and P40 showed complementary compression and energy-absorption characteristics.Topology-density grading promoted sequential crushing and delayed densification.At 125 J, TDDG reduced peak stress by 32.2% versus U-P30 and 24.6% versus DG-P20-P40.TDDG retained peak-stress mitigation across impact energies from 62.5 to 160 J.AbstractTriply periodic minimal surface (TPMS) lattices are promising lightweight impact absorbers, but high-fidelity finite element modeling is costly, and uniform designs can develop high stress peaks during densification. This study presents a voxel-based finite element framework and a topology–density dual-gradient (TDDG) TPMS absorber. A convergence study selected a voxel size of 0.33 mm, yielding a 1.11% relative-density error and converged mechanical responses. Compared with a converged C3D4 tetrahedral model, the C3D8R voxel model reduced wall-clock time from 4222 to 497 s. Following validation against quasi-static compression tests, P, G, and IWP topologies at 20%, 30%, and 40% relative densities were screened. IWP20 and P40 were assigned to the impact- and support-facing regions and connected by normalized sigmoid interpolation. Under a 125 J impact, simulations predicted that TDDG-IWP20-P40 reduced peak nominal impact stress by 32.2% and 24.6% relative to U-P30 and DG-P20-P40, respectively, while maintaining comparable SEA. Additional simulations at 62.5 and 160 J confirmed lower peak stress than U-P30, with the added benefit over density-only grading becoming more pronounced at higher impact energy. Progressive crushing and delayed densification demonstrate the potential of TDDG TPMS absorbers for impact-load mitigation and future aerospace buffer designs. 1. Introduction Spacecraft landing systems require lightweight buffer structures capable of reducing transmitted loads during touchdown while maintaining sufficient energy absorption capacity [1,2,3,4]. During landing, the absorber must dissipate kinetic energy within a limited stroke and suppress peak stress or acceleration transmitted to the protected structure [5,6]. Conventional landing buffer designs, including crushable honeycombs, metallic foams, thin-walled tubes, and shock absorbers, have been widely investigated for aerospace and planetary landing applications [7,8]. However, these structures often face trade-offs among mass efficiency, stable collapse, controllable deformation, and manufacturability, especially when the available volume and allowable peak load are constrained. Additively manufactured lattice structures offer a new design space for aerospace energy absorbers because their stiffness, strength, and collapse modes can be adjusted through topology and relative density [9,10,11,12,13,14,15]. Compared with stochastic foams and conventional honeycombs, architected lattices provide better geometric repeatability and more predictable mechanical behavior [16,17,18]. Recent studies have shown that lattice and cellular metamaterials can achieve high specific stiffness, high specific strength, programmable deformation, and multifunctional performance, making them attractive for aerospace structures where lightweight design and impact resistance are both required [19,20,21,22]. Among various lattice topologies, triply periodic minimal surface (TPMS) structures have attracted increasing attention because of their smooth continuous surfaces, high surface-to-volume ratio, controllable pore morphology, and absence of sharp strut intersections [23,24,25,26,27,28,29]. Typical TPMS topologies, such as Schwarz primitive (P), Gyroid (G), and I-graph and wrapped package (IWP), can be generated from implicit functions and fabricated by additive manufacturing. Their mechanical response can be tailored by changing the unit cell size, relative density, wall thickness, and loading direction [30,31,32,33]. Compared with beam-based lattices, sheet-based TPMS structures generally provide smoother stress transfer and improved deformation stability, which are beneficial for compression and impact energy absorption [34,35]. Functionally graded lattice structures further improve the design flexibility of energy absorbers by spatially varying density or topology. In graded structures, low-density regions can deform first and reduce the initial impact force, whereas high-density regions can provide late-stage support and delay complete densification [36,37,38,39]. However, most existing TPMS energy absorption studies focus on single-topology or density-only graded designs. The potential of hybrid graded structures that combine different TPMS topologies at different density regions remains insufficiently explored, especially for impact attenuation where the redistribution of energy absorption over time is critical. Reliable finite element modeling is also essential for TPMS impact analysis. STL-based TPMS geometries usually contain complex curved surfaces and large numbers of triangular facets, which may lead to time-consuming tetrahedral meshing and unstable contact behavior during large deformation. Voxel-based modeling provides an alternative by converting complex geometries into structured hexahedral meshes, which can simplify mesh generation and improve computational efficiency [40,41]. Nevertheless, the accuracy and efficiency of voxelized TPMS models must be evaluated through convergence analysis and comparison with conventional mesh strategies. To address the computational cost of high-fidelity TPMS modeling and the limited load-regulation capability of uniform or single-topology graded absorbers, this study proposes a voxel-based design and simulation framework for topology–density dual-gradient (TDDG) TPMS structures. The framework combines structured-hexahedral voxel modeling, quasi-static validation and constituent screening, and dynamic impact analysis. The density-dependent responses of the P, G, and IWP topologies are first evaluated to identify configurations with complementary deformation and energy-absorption characteristics. Based on this screening, a TDDG-IWP20-P40 absorber is constructed using a normalized sigmoid transition in both topology and relative density. Its impact response is compared with those of the uniform U-P30 and single-topology density-graded DG-P20-P40 structures to determine whether coordinated topology and density grading can mitigate peak impact stress while maintaining energy-absorption capacity. Particular attention is given to the relationship between progressive crushing, densification, and impact-load regulation. A conceptual cylindrical buffer core is also presented to examine the geometric transferability of the proposed architecture to aerospace buffer applications. 2. TPMS Design and Computational–Experimental Methodology 2.1. TPMS Geometric Design and Screening Matrix In this study, triply periodic minimal surface structures were chosen as the geometric foundation of the energy-absorbing lattices because of their continuous surfaces, periodic topology, and high geometric controllability. Three representative sheet-based TPMS topologies—P, G, and IWP—were adopted for this purpose. These topologies were screened at different relative densities to identify suitable topology–density combinations for the subsequent dual-gradient design. The implicit functions for the P, G, and IWP surfaces are defined as follows:(1)P:cosX+cosY+cosZ=C(2)G:sinXcosY+sinYcosZ+sinZcosX=C(3)IWP:2cosXcosY+cosYcosZ+cosZcosX −cos2X+cos2Y+cos2Z=C where C is the level-set parameter that controls the position of the surface. The normalized spatial coordinates X, Y and Z are defined as follows:(4)X=2πx/l, Y=2πy/l, Z=2πz/l where l is the unit cell size. x, y, z are the Cartesian coordinates. A sheet-based TPMS formulation was adopted in this study. Instead of using an infinitely thin mathematical surface, the sheet-based solid domain was generated by retaining the region between two level sets, C1 and C2:(5)C1≤Fx,y,z≤C2 where F(x, y, z) is the corresponding TPMS implicit function. The relative density of the TPMS lattice was controlled by adjusting the interval between C1 and C2, where C1 and C2 were set as opposite values. Each pair of C1 and C2 therefore corresponded to a specific relative density. To identify a suitable topology for subsequent hybrid graded design, three representative sheet-based TPMS structures were investigated, namely the P, G, and IWP topologies, as shown in Figure 1. For each topology, homogeneous specimens with relative densities of 20%, 30%, and 40% were generated, resulting in nine simulation groups in total. All specimens had the same geometric dimensions, with a unit cell size of 10 mm, a 3 × 3 × 3 periodic array, and an overall size of 30 mm × 30 mm × 30 mm. The topology screening matrix is summarized in Table 1. The screening was conducted to compare the stiffness, initial peak stress, energy absorption efficiency, and densification behavior of the nine topology–density combinations and to identify suitable candidates for the impact- and support-side regions of the dual-gradient absorber. 2.2. Voxel-Based Numerical Modeling Framework 2.2.1. STL-to-INP Voxelization Workflow The generated TPMS geometries were first exported as STL files, and the triangular facet models in the STL files were subsequently converted into voxel-based finite element INP models using an in-house Python (v2024.1) program, as shown in Figure 2. The purpose of the voxelization procedure was to transform complex TPMS structures into structured hexahedral meshes that could be directly imported into Abaqus (v2021) for compression and impact simulations. The program first determined whether the STL file was in ASCII or binary format, and then extracted the vertex coordinates and facet normal vectors using the corresponding reader. The vertex coordinates of the triangular facets were then used to define the geometric boundary of the TPMS structure. After reading the STL geometry, the bounding box of the model was calculated. For a model with bounding box dimensions Lx = xmax − xmin, Ly = ymax − ymin, and Lz = zmax − zmin, a regular Cartesian voxel grid was generated within the bounding box. The voxel resolution in the x, y, and z directions was prescribed as Nx, Ny, and Nz, respectively. The corresponding voxel sizes were defined as(6)Δx=LxNx, Δy=LyNy, Δz=LzNz Each voxel was represented by its center point,(7)Pijk=xmin+i+12Δx, ymin+j+12Δy, zmin+k+12Δz where i = 0, …, Nx − 1, j = 0, …, Ny − 1, and k = 0, …, Nz − 1. Each voxel was then classified as solid or void according to its position relative to the closed STL surface. A ray-casting method was used for the solid-void classification. Taking ray casting along the z-direction as an example, a ray was defined at each grid location as(8)rz=xi, yi, z Before calculating the exact intersection, triangular facets were first filtered according to their projected coordinate ranges. A triangular facet was considered a candidate intersecting facet only when(9)xmint≤xi≤xmaxt, ymint≤yj≤ymaxt where xmint, xmaxt, ymint and ymaxt are the projected coordinate bounds of the triangular facet. For each candidate triangular facet, the projected point (xi,yj) was further checked using a point-in-triangle criterion. In barycentric form,(10)xi,yj=λ1x1,y1+λ2x2,y2+λ3x3,y3 with(11)λ1+λ2+λ3=1 The ray was regarded as intersecting the triangular facet when(12)λ1≥0, λ2≥0, λ3≥0 The z-coordinate of the intersection point was then calculated from the plane equation of the triangular facet,(13)Ax+By+Cz+D=0 as(14)zint=−D−Axi−ByjC All intersection points along the ray were sorted in ascending order as(15)z1