Single-phase Fe0.5Co0.5S2 cathode material for long working time thermal batteries Authors: Hui Yang, Hai Zhou, Xinlu Li, Shaoming Qiao, Qibing Wu, Min Kang Published: 2026 ABSTRACT Multi-metal disulfides are widely employed as cathode materials for thermal batteries owing to their high electronic conductivity, high specific capacity, and exceptional stability of the cathode–separator interface. However, conventional synthesis methods for multi-metal disulfides suffer from low production efficiency. Herein, we report a scalable route to synthesize Fe–Co binary disulfide (Fe0.5Co0.5S2) via high-temperature solid-state sintering of a mixture of Fe–Co alloy and sublimed sulfur. The resulting Fe0.5Co0.5S2 possesses single-phase, high thermal stability, and low resistance, which effectively enhance its discharge capacity in thermal batteries. At a current density of 100 mA cm−2 and a discharge temperature of 460 °C, Fe0.5Co0.5S2 delivers a high specific capacity of 595.4 mAh g−1 with a cutoff voltage of 1.5 V. Notably, the specific capacity decreases by only 10.7% at a discharge temperature of 540 °C, indicating an extended working temperature range. As a result, the voltage upon constant and pulse current loading of Fe0.5Co0.5S2 in a 102 V thermal battery is obviously higher than that of the mechanically mixed FeS2/CoS2. This work provides a simple and efficient strategy for the preparation of binary disulfides for thermal batteries. Introduction The thermal battery is one kind of primary power source, which is widely used in aerospace equipment, aircraft ejection seats, etc. Thermal batteries can be activated rapidly (generally in less than 1 s) after the ignition of their pyrotechnic system by an external signal, during which the non-conductive molten salt is heated and melted into an ionic conductor.1–3 Thermal batteries have the advantages of high power and energy density, compact structure, long storage life, being maintenance-free and so on. Transition metal disulfides, such as FeS2, CoS2, and NiS2, are the main cathode materials for thermal batteries, owing to their superiorities of exceptional thermal stability, outstanding electronic conductivity, high specific capacity, and excellent stability of the cathode-separator interface.1–4 Different disulfides have their own advantages in terms of electronic conductivity, thermal stability, and voltage platform. For example, compared with CoS2, FeS2 has a slightly higher voltage platform, poorer thermal stability, and lower electronic conductivity.1–3 As a consequence, composites of disulfides are generally used as cathode materials for thermal batteries, in order to take advantage of each mono-disulfide. Hydrothermal method can effectively control the morphology and particle size of materials.5,6 It is generally used for the synthesis of heteroatom-doped surface-modified disulfides, such as CoxNi1−xS2,7–9 MoS2-CoS2,10 Co4S3 nanotube,11 and MoS2.12 Meanwhile, carbon modified disulfides can also be prepared via hydrothermal synthesis to improve the electronic conductivity.13,14 These materials generally possess excellent thermal battery performances, such as low polarization and high specific capacity. For instance, Co-doped NiS2 delivered a specific capacity of 434.8 mAh g−1 at 100 mA cm−2 with a cutoff voltage of 1.5 V, and a high energy density of 142.5 Wh kg−1 was achieved in a 66 ± 10 V thermal battery at 100 mA cm−2.7 However, the production efficiency of hydrothermal synthesis is very low. High temperature thermal sintering of a mixture of transition metal and sublimed sulfur can also be used to prepare mono-metal15 and multi-metal disulfides (e.g. heteroatom-doped NiS2 (ref. 16 and 17) and Ni0.5Co0.5S2).18 However, long-time ball-milling is required for the synthesis of disulfide composites to ensure the homogeneous dispersion of different metals. Meanwhile, disulfide composites can be directly synthesized via high temperature thermal sintering of a mixture of metal alloy and sublimed sulfur.19,20 In our previous work, FeNiCoS2 ternary disulfide was prepared via the high temperature sulfurization of Fe–Ni–Co alloy.19 The resulting FeNiCoS2 showed a high specific capacity of 601 mA h g−1 at a current density of 200 mA cm−2 and a discharge temperature of 460 °C with a cutoff voltage of 1.5 V. However, an obvious capacity loss (21.1%) was observed when the cell was discharged at 540 °C, due to the poor thermal stability of this ternary disulfide. This cathode material cannot meet the needs of long working time thermal batteries. As a thermally activated primary battery, the working time of a thermal battery largely depends on its thermal life, because it can supply energy only when the electrolyte is molten.21–23 The internal temperature of long working time thermal batteries is higher than that of conventional batteries, so as to ensure a longer thermal life. However, high temperature can lead to the decomposition of cathode materials with poor thermal stability,13,24 the generated sulfur vapor will react with the Li–B anode and produce a large amount of heat, which can lead to battery runaway. In this work, Fe0.5Co0.5S2 binary disulfide with a single phase is prepared via the direct sulfurization of Fe–Co alloy. The present Fe0.5Co0.5S2 possesses the superiorities of high thermal stability, low resistance, and high specific capacity in thermal batteries. Especially, the capacity decrease is only 10.7% when the discharge temperature rises from 460 to 540 °C, demonstrating excellent performance at high working temperatures. Furthermore, the performance of Fe0.5Co0.5S2 is investigated in a 102 V thermal battery, which demonstrates excellent long-time working ability and pulse loading capability. This work provides a simple and efficient strategy for large-scale preparation of Fe–Co binary disulfides with higher thermal battery performances than FeS2, CoS2, and the mechanically mixed FeS2/CoS2.19,25 Experimental Synthesis of materials Fe–Co alloy with a metallic molar ratio of 1 : 1 was used as the starting material to synthesize Fe0.5Co0.5S2. Fe–Co alloy and sublimed sulfur with a weight ratio of 1 : 3 were mixed using a mortar and pestle. The mixture was heated to 400 °C under Ar with a heating rate of 5 °C min−1 and maintained at 400 °C for 4 h. The resultant sample was further heated at 500 °C for 2 h under Ar to remove excess sulfur. FeS2 and CoS2 were also prepared via a similar method using Fe and Co powder as the metal source, respectively. The FeS2/CoS2 composite was obtained via mechanical mixing of FeS2 and CoS2 powders with a molar ratio of 1 : 1. Thermal battery assembling and testing The 0.25 g cathode and 0.45 g separator were pressed into a cathode/separator composite pellet with a diameter of 20 mm under 20 MPa. A Li–B pellet (60 wt% Li) with a thickness of 0.5 mm was used as the anode. Single cells were tested on an IT8511 plus single-channel programmable electronic load. Detailed information for the material characterization, single-cell fabrication, and test methods is presented in the SI. Thermal batteries with a peak voltage of 102 V were also manufactured by using Fe0.5Co0.5S2 and FeS2/CoS2 as cathode materials, respectively. A total of 3.6 g cathode material and 3.3 g separator were pressed into a cathode/separator composite pellet with a diameter of 66 mm. A Li–B pellet (60 wt% Li) with a thickness of 0.35 mm was used as the anode. A pressed Fe/KClO4 pellet was used as the internal pyrotechnic source. By using the typical thermal battery structure, the single cells were sealed in a stainless steel housing with a diameter of 78 mm and a height of 180 mm, forming a 102 V full thermal battery. The battery was activated and discharged at ambient temperature. Results and discussion Material characterization Fig. 1(a) presents the synthesis process of Fe–Co binary disulfide, and the structure diagram of a single cell and a full thermal battery. The material is prepared via high temperature sulfurization of Fe–Co alloy with a metallic molar ratio of 1 : 1, which is then used as cathode material for thermal batteries. As shown in Fig. S1, well-crystallized FeS2 and CoS2 are obtained via the high temperature sulfurization process using Fe and Co powder as the metal source, respectively. Accordingly, Fe–Co alloy can also be vulcanized by sulfur producing binary disulfide, and a complete mutual substitution of Fe and Co can be realized in a wide atomic concentration range due to the isomorphic feature of FeS2 and CoS2.26 X-ray diffraction (XRD) pattern of Fe–Co alloy is shown in Fig. S2, the diffraction peaks centered at 44.8 and 65.3° can be ascribed to the (110) and (200) crystal planes of Fe–Co alloy (PDF #44-1433). Fig. 1(b) shows the XRD pattern of the obtained material. The diffraction peaks are located between the characteristic diffraction peaks of FeS2 (PDF # 42-1340) and CoS2 (PDF # 41-1471), indicating a single-phase structure. Considering that Fe and Co will not be lost during the solid-state reaction and can be completely vulcanized by excessive sulfur, the composition of the resulting material should be Fe0.5Co0.5S2. (a) Schematic illustration of the synthesis process of Fe0.5Co0.5S2, and the structure of a single cell and a full thermal battery. (b) XRD pattern of Fe0.5Co0.5S2, (c) TG and DSC curves of Fe0.5Co0.5S2 and FeS2/CoS2 under Ar from room temperature to 800 °C with a heating rate of 10 °C min−1. The phase structure of the prepared samples was also analyzed by XRD Rietveld refinement, using a face-centered cubic crystal structure model. The results are shown in Fig. S3 and S4. The fitted pattern of Fe0.5Co0.5S2 possesses a low weighted profile factor (Rwp, 2.63%), suggesting a high credible fitting result (Fig. S3). The fitted unit cell parameter of Fe0.5Co0.5S2 is a = b = c = 5.4660 Å, which is between the fitted parameters of FeS2 (5.4163 Å) and CoS2 (5.5321 Å), confirming the formation of single-phase Fe0.5Co0.5S2. The ionic radius of Fe2+ (0.061 nm) is close to that of Co2+ (0.065 nm),27 which is beneficial for the mutual substitution of Fe and Co to generate single-phase Fe0.5Co0.5S2. The uniform substitution can efficiently modify the electronic structure of Fe and Co atoms in Fe0.5Co0.5S2,16,19,27 enhancing the electronic conductivity of Fe0.5Co0.5S2. As a result, Fe0.5Co0.5S2 is expected to possess excellent thermal battery performances, such as high electronic conductivity and high specific capacity. The thermal stability of cathode material is crucial for thermal batteries. The decomposition of disulfides decreases the capacity of cathode materials; the generated sulfur vapor reacts with the Li–B anode and produces a large amount of heat, which can make the heat of the battery run out of control. The thermal stability of Fe0.5Co0.5S2 and FeS2/CoS2 was tested by thermogravimetric (TG) analysis, as shown in Fig. 1(c). The TG curves of the two samples almost coincide with each other when the temperature is below 600 °C. Even so, the 5% mass loss temperature of Fe0.5Co0.5S2 (637.4 °C) is 10 °C higher than that of FeS2/CoS2, which is also higher than those of many other reported disulfides.16,27,28 Meanwhile, the differential scanning calorimetry (DSC) curve of FeS2/CoS2 displays two obvious endothermic peaks, which indicates that the main mass loss of FeS2/CoS2 can be divided into two stages, corresponding to the thermal decomposition of FeS2 and CoS2. For comparison, Fe0.5Co0.5S2 possesses only one endothermic peak located between the two peaks of FeS2/CoS2, which indicates that Fe0.5Co0.5S2 has one decomposition process, further confirming the single-phase structure. The decomposition temperature of CoS2 is considerably higher than that of FeS2,1,2 implying that Co–S bond possesses higher strength than Fe–S bond. As a result, the replacement of Fe–S bonds in FeS2 by Co–S bonds can improve the thermal stability of the Fe0.5Co0.5S2 solid solution. The scanning electron microscope (SEM) image of Fe–Co alloy is presented in Fig. 2(a), which indicates that the alloy is composed of microspheres with diameter of 10–30 µm. The SEM energy dispersive spectroscopy (EDS) mapping images confirm the uniform distribution of Fe and Co in the alloy (Fig. S5), the atomic ratio of Fe to Co is 1.06 : 1. After the high temperature sulfurization process, the resulting Fe0.5Co0.5S2 consists of irregular particles aggregated by small particles, forming a porous structure with a rough surface (Fig. 2(b and c)). Similar morphology is observed for FeS2 and CoS2 (Fig. S6).17,19 Small particles can shorten the transmission path of electrons and ions, and the porous structure can provide abundant diffusion channels for electrolyte, both of which help to improve the electrochemical performance.29 SEM EDS mapping images reveal the homogenous distribution of Fe, Co, and S elements throughout the Fe0.5Co0.5S2 particles (Fig. S7). SEM images of (a) Fe–Co alloy and (b and c) Fe0.5Co0.5S2 prepared via a high-temperature thermal sintering process. (d) TEM image, (e) HRTEM image, (f) SAED pattern, and (g) TEM EDS mapping images of Fe0.5Co0.5S2. The crystal structure of Fe0.5Co0.5S2 was also investigated by transmission electron microscopy (TEM). As shown in Fig. 2(d), the microparticle of Fe0.5Co0.5S2 displays an irregular sphere with a diameter of less than 150 nm. The clear and well-arranged lattice fringes in the high-resolution TEM (HRTEM) image confirm the good crystallinity of Fe0.5Co0.5S2 (Fig. 2(e)). The lattice fringe spacing of 0.313 nm can be ascribed to the (111) plane of Fe0.5Co0.5S2. The selected area electron diffraction (SAED) pattern further verifies the single-crystal feature of Fe0.5Co0.5S2 (Fig. 2(f)). Moreover, TEM EDS mapping images suggest the uniform distribution of different elements at the atomic scale in Fe0.5Co0.5S2 (Fig. 2(g)). The above results suggest that Fe0.5Co0.5S2 with excellent thermal stability and a single-phase structure can be obtained via the sulfurization of Fe–Co alloy. The chemical state and bonding environment of Fe0.5Co0.5S2 and FeS2/CoS2 were analyzed by X-ray photoelectron spectroscopy (XPS). Fe 2p3/2 spectra of Fe0.5Co0.5S2 and FeS2/CoS2 are fitted into three peaks, which can be assigned to Fe2+, Fe3+, and the satellite peak (Fig. 3(a)).30,31 Obviously, the Fe2+ and Fe3+ peaks of Fe0.5Co0.5S2 shift to higher binding energies as compared to those of FeS2/CoS2. Co 2p3/2 spectra of the two samples can be deconvoluted into four peaks corresponding to Co3+, Co2+, and the satellite peaks (Fig. 3(b)).8,15,32 The Co3+ characteristic peak of Fe0.5Co0.5S2 also shows a positive shift of 0.4 eV. S 2p spectra of the two samples can be fitted into three peaks centered at 162, 164, and 167 eV, corresponding to Sn2− (2p3/2), Sn2− (2p1/2), and S–O, respectively (Fig. 3(c)).16,17 Notably, the Sn2− peak of Fe0.5Co0.5S2 shows a negative shift of 0.3 eV compared to that of FeS2/CoS2. It should be noted that FeS2/CoS2 is the mechanical mixture of FeS2 and CoS2, thus, the chemical properties of Fe and Co in FeS2/CoS2 cannot be changed obviously in comparison to the corresponding mono-disulfides. The above analysis suggests that the outer-shell electrons of Fe and Co in Fe0.5Co0.5S2 are greatly regulated by mutual substitution forming an electron-defect state, which is more capable of accepting electrons than the mono-disulfides and/or mechanically mixed samples. As a result, Fe0.5Co0.5S2 is expected to deliver excellent thermal performances, such as low resistance and high specific capacity.33–35 (a) Fe 2p3/2, (b) Co 2p3/2, and (c) S 2p spectra of Fe0.5Co0.5S2 and mechanically mixed FeS2/CoS2. Single cell performance The thermal battery performance of Fe0.5Co0.5S2 was firstly evaluated by single cells, using Fe0.5Co0.5S2 and Li–B as the cathode and anode materials, respectively. Fig. 4(a) shows the discharge curves of Fe0.5Co0.5S2 at different current densities and a discharge temperature of 500 °C. Similar to many other disulfides,19,27 Fe0.5Co0.5S2 displays two obvious voltage plateaus. The voltage of the single cell decreases with increasing current density, due to the internal resistance of the cell. The calculated specific capacity of Fe0.5Co0.5S2 reaches 548, 425, and 339 mAh g−1 at current densities of 100, 200 and 400 mA cm−2, respectively, with a cutoff voltage of 1.5 V. Fig. 4(b) and (c) compare the discharge curves of Fe0.5Co0.5S2 and FeS2/CoS2 at current densities of 100 and 200 mA cm−2. It is noteworthy that the discharge curve of Fe0.5Co0.5S2 is significantly prolonged compared to that of FeS2/CoS2, and the specific capacity of Fe0.5Co0.5S2 at 200 mA cm−2 is 1.27 times that of FeS2/CoS2. It also outperforms the corresponding mono-disulfides (FeS2 and CoS2)19 and many other reported disulfides (Table S1). As a result, Fe0.5Co0.5S2 displays a greatly improved utilization of cathode material at high current densities, which is conducive to maintaining high energy density at a high power density. (a) Discharge curves of Fe0.5Co0.5S2 at different current densities. Discharge curves of Fe0.5Co0.5S2 and FeS2/CoS2 at (b) 100 mA cm−2 and (c) 200 mA cm−2. (d) Discharge curves and (e) specific capacity of Fe0.5Co0.5S2 at different temperatures. The capacity was calculated by the mass of electroactive material with a cut-off voltage of 1.5 V. (f) Pulse discharge curves and resistance of Fe0.5Co0.5S2 and FeS2/CoS2 at a constant current density of 100 mA cm−2 and a pulse current density of 500 mA cm−2 for 2 s every 30 s. To elucidate the discharge mechanism of Fe0.5Co0.5S2, XRD patterns of the material after discharge were collected at different cutoff voltages, as presented in Fig. S9. Upon discharge to 1.8 V, the characteristic diffraction peaks of Fe0.5Co0.5S2 vanish, while new diffraction peaks corresponding to Li2FeS2, Co9S8, and FeCo alloy emerge. When the cutoff voltage is further lowered to 0 V, the diffraction peaks of Li2FeS2 and Co9S8 disappear, accompanied by a notable increase in the intensity of the FeCo alloy peaks. These observations indicate that Li2FeS2 and Co9S8 serve as intermediate discharge products and are eventually converted into FeCo alloy. Based on these findings, the discharge mechanism of Fe0.5Co0.5S2 can be proposed as follows:1,2Fe0.5Co0.5S2 + Li → Li3Fe2S4 + Co3S4 + Li2SLi3Fe2S4 + Co3S4 + Li → Li2FeS2 + Co9S8 + Li2SLi2FeS2 + Co9S8 + Li → Fe + Co + Li2SFe + Co → CoFe The influence of discharge temperature on the thermal battery performance of Fe0.5Co0.5S2 was also investigated in the temperature range of 460–540 °C at 100 mA cm−2. As shown in Fig. 4(d), similar discharge curves are obtained at different temperatures. At a relatively low temperature (460 °C), the specific capacity of Fe0.5Co0.5S2 reaches 595.4 mAh g−1 with a cutoff voltage of 1.5 V (Fig. 4(e)). Due to thermal decomposition of the cathode material, the first voltage plateau shortens slightly with increasing discharge temperature, resulting in a decreased specific capacity. Even so, Fe0.5Co0.5S2 shows a high specific capacity of 531.5 mAh g−1 at 540 °C; the capacity loss is only 10.7% compared to the value obtained at 460 °C. For comparison, the capacity of FeS2/CoS2 is 476.1 mAh g−1 and 359.8 mAh g−1, respectively, at 460 °C and 540 °C, corresponding to a capacity retention of 75.4% (Fig. S8). The significant capacity loss of FeS2/CoS2 can mainly be ascribed to the decomposition of FeS2. The above results confirm that Fe0.5Co0.5S2 can still work normally at a temperature where ordinary materials are prone to failure, demonstrating an extended operating temperature range. The internal resistance of Fe0.5Co0.5S2 and FeS2/CoS2 was further investigated by pulse discharge tests. The cell was discharged at 100 mA cm−2 for 28 s, after which a pulse with a current density of 500 mA cm−2 and a width of 2 s was applied. The pulse was repeatedly applied for 20 times. The internal resistance (R, Ω) was calculated based on the equation R = (V1 − V2)/(I2 − I1),18,19 where V1 (V) and I1 (A) were the background voltage and current, V2 (V) and I2 (A) were the pulse voltage and current, respectively. The discharge curves and resistance are presented in Fig. 4(f). Notably, Fe0.5Co0.5S2 possesses a small and stable resistance with no obvious fluctuation or increase; the average value is 0.125 Ω, which is 0.023 Ω lower than that of FeS2/CoS2. Meanwhile, the internal resistance of Fe0.5Co0.5S2 is obviously lower than that of FeS2, even close to that of CoS2.19 The low resistance can enhance the transfer rate of electrons and promote the utilization of electroactive material, resulting in excellent thermal battery performance. The improved conductivity of Fe0.5Co0.5S2 can be ascribed to the following two reasons: (1) the mutual substitution between Fe and Co atoms in Fe0.5Co0.5S2 can optimize the conduction band and generate more charge carriers.36 (2) More importantly, the replacement of Fe atoms with Co facilitates the conversion of FeS2 from semiconductor to semimetal, significantly improving the electronic conductivity.26,37 Thermal battery performance The single cell performance suggests that single-phase Fe0.5Co0.5S2 has the advantages of high thermal stability, low resistance, high specific capacity and wide operating temperature range. Thus, full thermal battery with an operating voltage of 102 V was assembled to investigate the capability of Fe0.5Co0.5S2 in long working time battery. For comparison, FeS2/CoS2 was also used as cathode material to fabricate the battery. The battery was discharged at a constant current of 2.0 A for 1000 s, and a series of pulse currents with values of 12.6 A and 45 A was applied. The result is shown in Fig. 5. The peak voltage of the two batteries is consistent, and the discharge curves almost coincide with each other before 500 s. Owing to its high electronic conductivity, the battery using Fe0.5Co0.5S2 as the cathode material displays smaller voltage drop upon the application of pulse current. Impressively, the voltage of the battery using Fe0.5Co0.5S2 as the cathode material is very stable during the entire discharge process, decreasing by only 5.6%. By contrast, the voltage of the other battery starts to decrease after 500 s, and an obvious voltage drop is observed in the later operating time, resulting in a low voltage retention (86.2%). Discharge curves of the 102 V full thermal batteries at a constant current of 2.0 A (58 mA cm−2), and a series of pulse currents of 12.6 A (368 mA cm−2) and 45 A (1316 mA cm−2). Thermal batteries are one kind of high-temperature battery, which can work normally only when the molten electrolyte is melted into an ionic conductor. As a consequence, the internal temperature of long working time thermal batteries is higher than that of conventional batteries to ensure a longer thermal life. FeS2/CoS2 is the mechanical mixture of FeS2 and CoS2, FeS2 with a relatively low decomposition temperature can decompose gradually during the long time high temperature discharge process, leading to capacity loss, voltage drop, and an increase in internal resistance. This is unacceptable for thermal batteries with the requirement of high voltage accuracy, especially for the battery that needs to apply large pulse in the later working stage. More importantly, the generated sulfur vapor will react with the Li–B anode in the sealed metal housing and produce a large amount of heat, which might cause battery runaway in the worst case. By contrast, Fe0.5Co0.5S2 can deliver high capacity retention at 540 °C (Fig. 4(e)), implying that the decomposition of Fe0.5Co0.5S2 can be neglected in the full thermal battery. As a result, the voltage of the battery can remain stable for a long time. More importantly, the internal temperature of the battery will not increase significantly due to limited side reactions, and thus the battery safety can be guaranteed, especially during the unload process after activation. In addition, the high electronic conductivity of Fe0.5Co0.5S2 also helps to stabilize the battery voltage and improve the pulse current loading capacity. As a result, the performance of Fe0.5Co0.5S2 is significantly higher than that of conventional FeS2/CoS2 in long working time thermal batteries. Conclusions Single-phase Fe0.5Co0.5S2 is successfully prepared via the high temperature solid-state reaction between Fe–Co alloy and sublimed sulfur. Owing to its improved thermal stability and electronic conductivity compared to mechanically mixed FeS2/CoS2, the present Fe0.5Co0.5S2 exhibits excellent thermal battery performances, such as low resistance and high specific capacity. Notably, Fe0.5Co0.5S2 delivers a high specific capacity of 595.4 mAh g−1 at a current density of 100 mA cm−2 and a discharge temperature 460 °C with a cutoff voltage of 1.5 V. Meanwhile, a high capacity retention of 89.3% is also obtained at the discharge temperature of 540 °C, demonstrating excellent performance over a wide operating temperature range. As a result, the voltage of the full thermal battery using Fe0.5Co0.5S2 as the cathode material is very stable during the discharge process, showing a voltage decrease of only 5.6% after 1000 s. In this work, a simple and efficient strategy is developed for the large-scale preparation of high performance Fe–Co binary disulfides, which is of great significance for practical application in long working time thermal batteries. Conflicts of interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper. Supplementary Material