One-argument Lie scaling and sensitivity analysis of UCM liquid flow over a vertical wedge using response surface method Authors: Musharafa Saleem, Imran Siddique, Mohamed Abubakar Fiidow, Rifaqat Ali, Bushra Shakoor, Barno Abdullaeva, Rana Muhammad Zulqarnain Published: 2026 ABSTRACT Wedge geometries are widely used in aerodynamics, heat exchangers, solar collectors, and chemical processing equipment. This study focuses on the combined impacts of thermal radiation, latent heat of fusion, Hiemenz flow, Joule heating, and electro-magnetohydrodynamic (EMHD) flows on the natural convection flow over a vertical wedge, which has not been examined previously. Due to the wide range of engineering applications involving wedge geometries, it is important to consider and discuss the effects of different thermophysical properties on the flow and heat transfer behavior. We examined upper-convected Maxwell (UCM) viscoelastic liquid flow in a permeable medium with phase change (melting effects). A one-argument scaling method has been introduced for transforming the developed equations of the liquid flow model into non-linear ordinary differential equations (ODEs). The numerical solution of the ODEs with boundary conditions is explored using the BVP4C technique, and the results are shown in graphs and analyzed. The velocity of the fluid increases with the magnetic field, porosity, electric field, Deborah number, suction, melting heat, and Hiemenz flow, while it decreases with higher Prandtl number. Similarly, the temperature distribution is enhanced by porosity, Prandtl number, melting heat, Hiemenz flow, as well as magnetic and electric field effects. The sensitivity analysis reveals that the melting heat parameter significantly enhances the Nusselt number (≈ 18.98%), establishing it as the most dominant factor in thermal energy transmission, while suction contributes moderately with a stable variation of ≈ 19.57%. In contrast, the Hiemenz parameter exhibits a negligible negative influence (nearly 200 times smaller), confirming its minimal role in affecting heat transfer performance. Introduction In the last several decades, non-Newtonian fluids have gained considerable interest as the behavior of such fluids is rather complicated, and the scope of industrial and technological use is also very broad. Their rheological behaviors cannot be explained by a single linear relationship between strain rate and stress, and hence several mathematical models have been proposed as being able to explain their behaviors. The UCM model is one of the most relevant and most researched viscoelastic models. The most crucial aspect of the UCM model is that it can achieve the elastic effects of non-Newtonian fluids that are essential, using the relaxation time concept, with a comparatively simple mathematical form compared to most other sophisticated models. In contrast to purely viscous models, the UCM model is effective in capturing the effects of memory and stress relaxation, which is important in processes where rapid deformation or stretching occurs. Owing to such characteristics, UCM fluids have found specific applications in areas like polymer processing, food manufacturing, drug delivery systems and thermal enhancement technologies. The fact that they can capture the effects of viscoelastic behavior renders them more appropriate compared to most other non-Newtonian models, where the elastic contribution is a leading factor. Over the last few years, scholars have delved into various issues of UCM fluid flows when physical conditions are varied. Reddy et al.1 examined the effect of an inclined magnetic field on thermal and mass transfer properties of turbulent squeeze flow of UCM fluid. Their results showed that there were observable differences in thermal conductivity in the inclination of the magnetic field. The study by Zeb et al.2 involves the evaluation of the influence of thermal stratification on the MHD stagnation-point flow of a UCM fluid over a porous surface. The experiment brought out great variations in the thermal behaviour in the heat generation and absorption processes. The study by Rahaman et al.3 focused on the induced movement of UCM fluid in a long oscillating cylinder in longitudinal and torsional vibrations. They found that the condition of boundary slips highly influence the flow characteristics. Salawu et al.4 examined the effect of radiation and chemical reaction on a magnetized UCM stagnation point with a particle-laden flow. Their work was useful in the understanding of microfluidic and biomedical uses. Asmadi et al.5 presented the transport of thermal energy in MHD UCM fluid flow over a horizontal wedge with the Cattaneo-Christov heat flux model and focused on non-Fourier heat conduction effects. Abu-Nab et al.6 studied the dynamics of microcavitation and the formation of ternary hybrid nanofluids, which contributes to the knowledge of advanced nanoliquid systems. Das et al.7 examined how the concept of double diffusion affects the thermal transport ability of quadra hybrid nanofluids, especially in engine oil. Moreover, Muhammad et al.8 have written an MHD UCM fluid flow model based on the spectral relaxation method, taking into consideration the effect of the double diffusion. Khan et al.9 suggested a model of the magnetized stagnation-point flow of a UCM nanofluid with slip boundary conditions and deal of thermal dispersion. Moreover, a computational work of the MHD Maxwell hybrid nanofluid flow was done by Alkasasbeh10, where the authors emphasized the significance of the double dispersion phenomenon. EMHD can be understood as a specialized extension of magnetohydrodynamics (MHD). While classical MHD studies the interaction between magnetic fields and the overall motion of electrically conducting fluids (including both ions and electrons), EMHD focuses specifically on the dynamics of the electron fluid, if the ions remain nearly stationary. The fundamental principles of MHD are governed by the conservation of mass, momentum, and energy, coupled with simplified (low frequency) forms of Maxwell’s equations to describe magnetic field transport. Once the basic theory is understood, the practical significance of MHD becomes quite evident from its broad range of applications. In both science and engineering, MHD is widely used to study plasma behavior, astrophysical processes, controlled nuclear fusion, and various aspects of space research. It also plays an important role in industry, particularly in controlling fluid motion in cooling systems, metallurgical processes, and energy conversion technologies. EMHD, on the other hand, is especially relevant in situations involving strong electromagnetic fields and small-scale effects. It finds applications in pulsed plasma devices, fusion-related studies, astrophysical modeling, and even solid-state physics. Because EMHD can describe electromagnetic interactions at a finer scale, it has become an important tool in modern plasma research and advanced technological developments. Among the earlier contributions in this area, Pantokratoras and Magyari11 examined the EMHD boundary-layer flow over a Riga plate. Their work showed that electromagnetic forcing can be used to control free convection and significantly alter the structure of the boundary layer. This work laid a strong theoretical foundation for understanding EMHD-driven flows in thermal systems. Buren and Jian12 applied EMHD analysis to microscale configurations by considering flow in between two micro-parallel plates that are transversely wavy. Their findings demonstrated the relevance of electromagnetic actuation to microfluidic devices and demonstrated the ability of EMHD to control flow properties within confined geometries, which is highly applicable in lab-on-chip and biomedical technologies. Prakash et al.13 also continued the work by evaluating the EMHD non-Newtonian ternary hybrid nanofluid flow over a wedge embedded in Darcy-Forchheimer porous medium. Using an extension of the EMHD theory through the addition of effects like the zeta potential and the wall suction/injection, they have included effects that have given them a complete computational model that links the EMHD theory with porous media transport and nanofluid engineering. Their experiment revealed that electromagnetic forces, porous resistance, and nanoparticle dynamics are all strongly coupled. Bharathi and Prakash14 examined the synergistic effect of the zeta potential and activation energy on the EMHD non-Newtonian nanofluid flow in a wedge within a porous medium in the Darcy-Forchheimer regime. Their effort focused on the effect of the electrokinetic and chemical reaction in the alteration of the velocity, temperature, and concentration distributions to increase the scope of EMHD applications to reactive and energy-sensitive systems. In much more recent work, Daniel et al.15 examined unsteady EMHD mixed convective flow of a dual stratified nanofluid including radiative heat transfer and Ohmic effects. Their results also emphasised the importance of thermal radiation and Joule heating in the betterment or regulation of heat transfer performance, especially in the areas of high temperatures and energy. A wedge is a solid body formed by two plane surfaces that meet at an angle, creating a sharp edge at the front. In fluid mechanics, a wedge-shaped surface is often used to study boundary-layer flow because geometry produces a pressure gradient along the surface. When a wedge is placed vertically and its surface is stretched along the length, the stretching motion of the surface drags the nearby fluid and forms a boundary layer along the wedge. The wedge geometry controls the external velocity distribution, while the stretching of the surface supplies additional momentum to the fluid. If the wedge is vertical, gravity may also influence the flow, so buoyancy can affect the velocity and temperature fields. When a wedge-shaped surface is placed in a flowing fluid and starts melting, the melted material mixes into the fluid and affects the flow near the surface. This melting changes the temperature distribution and can make the layer of heated fluid thicker or thinner depending on how fast the melting happens. It also slightly changes the speed of the fluid close to the wedge. In short, melting heat effects describe how the heat from the fluid causes the wedge to melt and how this melting influences both the fluid flow and the transfer of heat near the surface. When Budhia and Kreith16 investigated the effect of melting or freezing at a wedge surface on heat transfer, they found that the phase change has a strong influence on the thermal boundary layer and heat flux. Kuo17 used the differential transformation technique in solving the Falkner-Skan wedge flow, which offered an effective mathematical technique in predicting velocity and temperature fields. Sarkar and Endalew18 studied the influence of the melting on the flow of Casson nanofluid in a porous medium under the influence of a magnetic field, including the role of the phase change and non-Newtonian flow in velocity and temperature distributions. Chakraborty and Janapatla19 studied the flow of a Casson nanofluid in a wedge at conditions of varying magnetic fields, thermal radiation, and melting, and demonstrated their effect on heat transfer and the thickness of the boundary layer. The analysis of radiative hybrid nanofluid flow over a melting wedge heat transfer by Hafeez, Liu and Khalid20 focused on the uses in which melting has a significant impact on the behaviour of the thermal and fluid field. Joule heating happens when an electric current passes through a fluid or material and produces heat, like how a wire gets warm when electricity flows. Thermal radiation is the heat that travels in the form of electromagnetic waves, so even without touching, hot objects can warm their surroundings. Heat sources and sinks are ways to add or remove heat from a system—like a heater adding warmth or a cooling fan taking heat away. Together, these effects describe different ways energy can enter or leave a fluid, changing its temperature and flow behavior. Merging the complexities of the porous-medium, defined by the Darcy and Brinkman resistive forces into modeling flow with UCM liquids, are crucial to the explanation of transport phenomena related to oil recovery, filtration, and subsurface flows. This merger thus leads to problems of formulation of governing equations and solutions. A genuinely robust methodology, analytical, and numerical becomes needed for revealing the interaction of the viscoelastic stresses with the permeability-induced resistance of the medium. Choudhary et al.21 proposed a mass-based hybrid nanoliquid framework for investigating MHD flow over a wedge embedded in a porous medium. Attention has been paid to the prime role of thermal radiation in modulating the characteristics of thermal energy transmission in the hybrid nanoliquid system. Various industrial processes involving the transport of NNFs in porous media include solutions of shear-thinning biopolymers, which find numerous applications in petroleum geology for improving petroleum recovery, mainly for their capacity to reduce displacement front spreading uncertainty and predictability and, therefore, recovery rate and accuracy. Current approaches for efficient ground environmental clean-up are exploring the use of shear-thinning polymer interruptions as a means of transporting iron nano-particles inside ground environments, as presented by Vecchia et al.22, Zhong et al.23, and Tosco et al.24. Modeling the pressure drop developed during non-Newtonian fluid transport in a porous medium is a core concern in each of the above applications. This problem has been dealt with comprehensively through detailed expressions of Darcy’s equation as advanced by Pearson & Tardy25 or through similarity solutions for transient simulations as offered by Ciriello, Di Federico26. In micro-scale simulation, the relevance of both pore network simulations and realistic pore-scale simulations is shown in Blunt’s work27. In this regard, further hybrid simulations involving both pore and micro-scale simulations are also shown in the work of Battiato et al.28. Sohail et al.29 analyzed entropy generation in a Darcy–Forchheimer squeezed hybrid nanofluid flow between rotating disks, showing how thermal radiation and viscous dissipation affect energy losses. Waseem et al.30 investigated 3D stretched magnetized hybrid nanofluid flow by taking note of the synergistic effect of the thermal radiation and heat generation on thermal efficiency. Waseem et al.31 applied the best homotopy asymptotic technique to investigate the process of entropy generation in hybrid nanofluids that have temperature-dependent thermal conductivity under radiation, that offer information on improved thermal management. In the study by Sohail et al.32, the Maxwell nanofluid bio-convective boundary layer flow over a stretched sheet was investigated, and it was found that the effects of radiation and Darcy-Forchheimer begin to play roles in the flow and heat transfer. Sohail et al.33 discussed the three-dimensional stretched Casson nanofluid flow in a rotating frame under bio-convection, indicating how it influences velocity and temperature distributions. Sohail et al.34 studied the mass and heat transport of bi- directional stretched Sisko fluid flow with variable magnetic fields and radiation, paying special attention to the interplay between magnetic and radiative and non-Newtonian effects. Sohail and Abbas35 examined the flow of non-Newtonian Prandtl fluid at a constant Reynolds number but with a diffusion coefficient and thermal conductivity that depend on the flow’s position, and the impact of altered heat and mass fluxes on the thermal and concentration distributions appear. Swain et al.36 examined bio-convectional flow of Williamson nanofluid over an expanding surface and revealed the effect of activating energy on the fluid movement and heat transfer. Swain et al.37 investigated the impact of dissipative heat on non-Newtonian Walter B nanoliquid on an elongating surface using a permeable medium, and the overall influence of internal heat generation and fluid characteristics on thermal conductivity. Swain et al.38 examined a bio-thermal reactor using nanofluid in the decomposition of organic waste in 3D flow in parallel channels, which focuses on the importance of non-uniform heat sources and chemical reactions to improve efficiency and temperature control. Various solution methodologies have been developed, addressing this challenge and others, toward solving DEs, which come in two broad categories: linear and nonlinear. Of these methods, Lie group theory has emerged as one of the most powerful analytical tools for nonlinear PDEs. From its original development by Sophus Lie, this method seeks the invariance properties of DEs that exhibit continuous symmetries under one-argument Lie group transformations. The approach has widely been used in studying liquid dynamics problems with different physical constraints. For example, Kandasamy et al.39 used Lie group transformations to study electrically conducting, impermeable, steady flow over a vertically stretchable sheet. Similarly, Nabwey et al.40 analyzed mixed convection stagnation point flow of non-Newtonian nanoliquids over an extensible vertical surface, which remains an important topic in nanoliquid research. Moreover, Nabwey and El-Mkny41 investigated the thermophoretic transport through vertical surfaces embedded in porous media using the concept of Lie symmetry transformations, particularly focusing on the migration of particles and the transfer of thermal energy. In another work, the authors42 replicated the solution for natural convection flow of nanoliquids through porous media over chemically reactive horizontal surfaces using Lie group transformation. Further, the authors Ullah and Zaman43 explored MHD slip flows for the hyperbolic tangent law over extensible surfaces via the theories of Lie transformation groups. The mixed convection and multi-physical interactions between symmetry-based analysis of three-dimensional EMHD nano-Carreau fluid flow over a Riga-stretched surface by Saleem et al.44 revealed that the velocity and temperature distributions in the flow are affected by these factors. Saleem and Faheem45 compared the combined effects of melting heat on aligned MHD Williamson nanofluid with microorganisms in the presence of the leading edge, and the differences in the effects phase change and bio-convection have on the flow and thermal behavior were illustrated. Chakraborty and Janapatla46 examined the flow of MHD nanoliquid over a vertical wedge with double dispersion and Dufour effects and examined the effects of the two means of transport on the boundary layer heat and mass transfer. Optimization is concerned with the search for the optimal solution to a problem, e.g. performance, efficiency or cost, and it is usually characterized by interrelating variables. RSM can be useful because it enables the development of an understandable representation of the impact of these variables on the outcome and identifies the most desirable combination without trying all of them. The typical steps of RSM are: (1) selecting the important variables and defining their ranges, (2) designing experiments to systematically explore the combinations, (3) performing the experiments or simulations and collecting data, (4) fitting a mathematical model, usually a polynomial, to describe the relationship between inputs and outputs, often verified using ANOVA (Analysis of Variance) to ensure the model is statistically significant, and (5) analyzing the model to find the optimum conditions. In most cases, an R-squared value approaching 95% or above is considered an indication of a well-fitted model, reflecting a strong agreement between predicted and observed results. Alongside this, sensitivity analysis plays an important role by examining how variations in input parameters influence the outcome. In this way, it helps identify which variables have the most significant impact on the system. When used together, RSM and sensitivity analysis provide a clearer understanding of the underlying behavior of the model, allowing researchers to focus on the most influential factors and make better design and optimization decisions. Several recent studies have effectively used these approaches in the context of nanofluid flow and heat transfer. For example, Panda et al.47 employed RSM to optimize heat transfer in a three-dimensional micropolar nanoliquid flow over a cylindrical surface, considering magnetic effects, viscous dissipation, and thermal radiation. Similarly, Baithalu et al.48 investigated the role of nanoparticle shape in micropolar hybrid nanoliquid flow over a vertical plate and determined the optimal thermal energy transmission rate using RSM. Further contributions by Sarfraz and Khan49, Muhammad et al.50, and Senbagaraja and De51 provide detailed insights into the combined use of sensitivity analysis and RSM, particularly in optimizing thermal systems and understanding the influence of multiple physical parameters under complex flow conditions. Motivation and novelty: This study uniquely combines thermal radiation, melting heat, Joule heating, and EMHD effects in the analysis of UCM liquid flow over a vertical wedge, an area not previously52,53 explored in this configuration. The study also considers wedge flow to analyze how the wedge angle and pressure-gradient parameter affect the UCM fluid behavior under thermal and EMHD effects. It introduces a novel integration of RSM with sensitivity analysis to optimize thermal energy transmission and assess the influence of key arguments. The application of a one-argument scaling transformation to handle complex nonlinear governing equations in a multi-physical environment adds further originality. Additionally, the study provides new insights into the effect melting conditions on viscoelastic liquid behavior, offering practical relevance for thermal system design and optimization. In recent years, considerable efforts have been made to analyze UCM fluid flows under different physical influences, leading to several important questions. In what way does the wedge flow parameter influence the velocity, temperature, and melting behaviors of a UCM fluid when EMHD and Joule heating effects are present?How can the wedge velocity be introduced through a one-parameter Lie group scaling transformation?In what manner are melting, thermal convection, and EMHD effects incorporated within the similarity analysis?How can the governing PDEs be reduced to ODEs using the Lie scaling technique? In what way does the wedge flow parameter influence the velocity, temperature, and melting behaviors of a UCM fluid when EMHD and Joule heating effects are present? In what way does the wedge flow parameter influence the velocity, temperature, and melting behaviors of a UCM fluid when EMHD and Joule heating effects are present? How can the wedge velocity be introduced through a one-parameter Lie group scaling transformation? How can the wedge velocity be introduced through a one-parameter Lie group scaling transformation? In what manner are melting, thermal convection, and EMHD effects incorporated within the similarity analysis? In what manner are melting, thermal convection, and EMHD effects incorporated within the similarity analysis? How can the governing PDEs be reduced to ODEs using the Lie scaling technique? How can the governing PDEs be reduced to ODEs using the Lie scaling technique? Mathematical modeling The present study investigates a steady, two-dimensional, laminar natural convection flow of an incompressible and electrically conducting UCM viscoelastic fluid over a vertical wedge placed in a porous medium. The model includes the effects of thermal radiation, melting heat, Joule heating, and EMHD, subject to a no-slip boundary condition at the wedge surface. The wedge velocity is defined as \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:{u}_{e}\left(\stackrel{-}{x}\right)=c{\stackrel{-}{x}}^{m}$$\end{document} in the free stream, where m is the power-law wedge parameter. The wedge surface is assumed to be electrically conducting, with a uniform vertical magnetic field \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:{B}_{0}\:$$\end{document}and an applied electric field \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:{E}_{0}$$\end{document}, producing Lorentz forces that modify the fluid momentum. The flow passes through a porous medium, represented via Darcy’s law, introducing a resistive force proportional to velocity. Physically, the stagnation term represents the slowing down of fluid as it approaches the wedge tip due to the pressure gradient along the surface. It reflects the high-pressure region near the leading edge where the flow must decelerate and turn to follow the wedge geometry52,53. Figure 1 represents the physical modeling of our problem. Fig. 1Geometry of the problem. Geometry of the problem. The objectives of the current study are: To investigate the natural convection behavior of a UCM viscoelastic liquid flowing past a vertical wedge embedded within a porous medium.To consider thermal radiation, melting heat, Joule heating, and EMHD forces in the analysis.To apply no slip boundary condition to the wedge surface.To transform the governing equations into a set of nonlinear ODEs through one-argument scaling approach.To resolve the ODEs employing the shooting method within MATLAB’s bvp4c solver.As to the application of RSM and sensitivity analysis for tuning the value of arguments and quantifying the relative impact of each physical factor.To study the effect of variations in chosen arguments on velocity and thermal energy transmission close to the wedge surface. To investigate the natural convection behavior of a UCM viscoelastic liquid flowing past a vertical wedge embedded within a porous medium. To investigate the natural convection behavior of a UCM viscoelastic liquid flowing past a vertical wedge embedded within a porous medium. To consider thermal radiation, melting heat, Joule heating, and EMHD forces in the analysis. To consider thermal radiation, melting heat, Joule heating, and EMHD forces in the analysis. To apply no slip boundary condition to the wedge surface. To apply no slip boundary condition to the wedge surface. To transform the governing equations into a set of nonlinear ODEs through one-argument scaling approach. To transform the governing equations into a set of nonlinear ODEs through one-argument scaling approach. To resolve the ODEs employing the shooting method within MATLAB’s bvp4c solver. To resolve the ODEs employing the shooting method within MATLAB’s bvp4c solver. As to the application of RSM and sensitivity analysis for tuning the value of arguments and quantifying the relative impact of each physical factor. As to the application of RSM and sensitivity analysis for tuning the value of arguments and quantifying the relative impact of each physical factor. To study the effect of variations in chosen arguments on velocity and thermal energy transmission close to the wedge surface. To study the effect of variations in chosen arguments on velocity and thermal energy transmission close to the wedge surface. To achieve the above objectives, we have the following assumptions considered regarding our problem: The liquid motion is described as steady, two-dimensional, and laminar for an incompressible UCM viscoelastic liquid.Over a vertical wedge that is confined within a porous medium, the liquid flows.Energy equation accounts for thermal radiation, heat that comes with phase change (melting), and Joule heating.An EMHD phenomenon is established that involves both transverse magnetic and electric fields.The Boussinesq approximation is taken, without the variations in density within the term for buoyancy.Vertical gravity effects cause the initiation of natural convection in the system.Effects of chemical reactions and mass diffusion are not considered.The governing equations are nondimensionalized using a one-argument, and a system of nonlinear ODEs is obtained.Simplification of momentum and energy equations is gained by way of boundary layer approximations. The liquid motion is described as steady, two-dimensional, and laminar for an incompressible UCM viscoelastic liquid. The liquid motion is described as steady, two-dimensional, and laminar for an incompressible UCM viscoelastic liquid. Over a vertical wedge that is confined within a porous medium, the liquid flows. Over a vertical wedge that is confined within a porous medium, the liquid flows. Energy equation accounts for thermal radiation, heat that comes with phase change (melting), and Joule heating. Energy equation accounts for thermal radiation, heat that comes with phase change (melting), and Joule heating. An EMHD phenomenon is established that involves both transverse magnetic and electric fields. An EMHD phenomenon is established that involves both transverse magnetic and electric fields. The Boussinesq approximation is taken, without the variations in density within the term for buoyancy. The Boussinesq approximation is taken, without the variations in density within the term for buoyancy. Vertical gravity effects cause the initiation of natural convection in the system. Vertical gravity effects cause the initiation of natural convection in the system. Effects of chemical reactions and mass diffusion are not considered. Effects of chemical reactions and mass diffusion are not considered. The governing equations are nondimensionalized using a one-argument, and a system of nonlinear ODEs is obtained. The governing equations are nondimensionalized using a one-argument, and a system of nonlinear ODEs is obtained. Simplification of momentum and energy equations is gained by way of boundary layer approximations. Simplification of momentum and energy equations is gained by way of boundary layer approximations. The thermophysical properties of the liquid are considered constant throughout the flow, except density variations, which are assumed to influence only the body force term in the momentum equation. The analysis further assumes local thermal equilibrium, along with the homogeneity and isotropy of the liquid. The resulting boundary layer equations for the current modeled issue provide a comprehensive and detailed depiction of the system, based on applying the previously mentioned assumptions and approximations1–5,11–14.1\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\frac{{\partial \bar {u}}}{{\partial \bar {x}}}+\frac{{\partial \bar {v}}}{{\partial \bar {y}}}=0$$\end{document},2\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{gathered} \mathop {\bar {u}} \frac{{\mathop {\partial \bar {u}} }}{{\mathop {\partial \bar {x}} }}+\mathop {\bar {v}} \frac{{\mathop {\partial \bar {u}} }}{{\mathop {\partial \bar {y}} }}=\nu \frac{{{\partial ^2}\mathop {\bar {u}} }}{{{{\mathop {\partial \bar {y}} }^2}}} - \lambda \left( {{{\mathop {\bar {u}} }^2}\frac{{{\partial ^2}\mathop {\bar {u}} }}{{ {{\mathop {\partial \bar {x}} }^2}}}+{{\mathop {\bar {v}} }^2}\frac{{{\partial ^2}\mathop {\bar {u}} }}{{ {{\mathop {\partial \bar {y}} }^2}}}+2\mathop { \bar {u}} \mathop { \bar {v}} \frac{{{\partial ^2}\mathop { \bar {u}} }}{{ \mathop {\partial \bar {x}} \mathop {\partial \bar {y}} }}} \right) - \frac{\nu }{K}\left( {\mathop { \bar {u}} +\lambda \mathop {\bar {v}} \frac{{ \mathop {\partial \bar {u}} }}{{ \mathop {\partial \bar {y}} }} - {{\mathop {\bar {u}} }_e}} \right)+{\mathop {\bar {u}_e}}\frac{{{{\mathop {\partial \bar {u}} }_e}}}{{\mathop {\partial \bar {x}} }} \hfill \\ \;\;+\frac{\sigma }{\rho }\left( {{E_0}{B_0} - B_{0}^{2}\left( {\mathop {\bar {u}} +\lambda \mathop { \bar {v}} \frac{{ \mathop {\partial \bar {u}} }}{{ \mathop {\partial \bar {y}} }}} \right)+B_{0}^{2}{{\mathop { \bar {u}} }_e}} \right)+g{\beta _T}\left( {T - {T_m}} \right)cos\gamma , \hfill \\ \end{gathered}$$\end{document}3\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\mathop {\bar {u}} \frac{{\partial T}}{{ \mathop {\partial \bar {x}} }}+\mathop { \bar {v}} \frac{{\partial T}}{{\partial \mathop {\partial \bar {y}} }}=\alpha \frac{{{\partial ^2}T}}{{ {{\mathop {\partial \bar {y}} }^2}}}+\frac{{16{\delta ^*}{T_\infty }^{3}}}{{3{k^*}\left( {\rho {c_p}} \right)}}\frac{{{\partial ^2}T}}{{{{\mathop {\partial \bar {y}} }^2}}}+\frac{\sigma }{{\left( {\rho {c_p}} \right)}}{\left( {{B_0}\left( {\mathop { \bar {u}} - {{\mathop {\bar {u}} }_e}} \right) - {E_0}} \right)^2}+\frac{{{Q_0}}}{{\left( {\rho {c_p}} \right)}}\left( {T - {T_m}} \right).$$\end{document} The suitable boundary conditions are20: \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\mathop {\bar {u}} =0,\quad T={T_m},\mathop { \bar {v}} = - {v_w}\left( x \right)+\frac{k}{{\rho \left[ {L+{C_s}\left( {{T_m} - {T_0}} \right)} \right]}}\frac{{\partial T}}{{\mathop {\partial \bar {y}} }},~{\mathrm{at}}~\;\mathop { \bar {y}} =0,$$\end{document} 4\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\mathop {\bar {u}} \to {\mathop {\bar {u}_e}}=c{\mathop {\bar {x}^m}},\quad T\;\; \to {T_\infty },~~~~~{\mathrm{as}}\quad \mathop { \bar {y}} \to \infty .$$\end{document} Thermal radiation is also included in the analysis, employing the Rosseland approximation, where the Stefan-Boltzmann constant \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:{\delta\:}^{*}$$\end{document} and mean absorption coefficient \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:{k}^{*}$$\end{document}account for the temperature difference between the surface and the nanoparticles within the flow field, based on studies by15–19. \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:{k}^{*}$$\end{document}represents the mean absorption coefficient and K represents the porosity of the medium. \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:\gamma\:=\pi\:\omega\:$$\end{document} is the angle of the wedge. \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:\omega\:$$\end{document} is the Hartree pressure gradient, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:{T}_{m},{T}_{\infty\:}$$\end{document} are the temperatures of the liquid at the melting surface of the wedge and the long distance from the wedge, respectively. Here \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:\alpha\:$$\end{document} represents the effective thermal diffusivity, which is expressed as \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:\alpha\:={\alpha\:}_{m}+\gamma\:d\stackrel{-}{u}$$\end{document}, where \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:{\alpha\:}_{m}$$\end{document} is the molecular thermal diffusivity and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:\gamma\:du\:$$\end{document}is thermal dispersion. When we assume the wedge surface along \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:x-axis\:(y=0)$$\end{document} is considered, there is no velocity perpendicular to the surface; hence, the y-component of the velocity vector does not exist. It is considered that the wedge cannot produce any changes to the liquid’s velocity at infinity, and hence \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:{\partial \bar {y}}\to\:\infty\:$$\end{document}, the velocity along \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:x-axis\:$$\end{document}is equal to the free stream velocity \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:{{\partial \bar {u}}}_{e}$$\end{document}. Introducing the following non-dimensionless variables46 for the conversion of the set of governing Eq. 5\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$x=\frac{{\mathop { \bar {x}} }}{L},~~ y=\frac{{P{e^{\frac{1}{2}}}}}{L}\mathop {\bar {y}},~~u=\frac{L}{{{\alpha _m}Pe}}\mathop { \bar {u}},~~v=\frac{L}{{{\alpha _m}P{e^{\frac{1}{2}}}}}\mathop {\bar {v}},~~\theta =\frac{{T - {T_m}}}{{{T_\infty } - {T_m}}},~~{u_e}=\frac{L}{{{\alpha _m}Pe}}{\mathop {\bar {u}_e}},$$\end{document} where, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$Pe=\frac{{{U_\infty }L}}{{{\alpha _m}}}$$\end{document} represents the Peclet number, L is the characteristic length, we choose the non-dimensional form of x and y accordingly. After using Eq. (5), we have the following6\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\frac{{\partial u}}{{\partial x}}+\frac{{\partial v}}{{\partial y}}=0,$$\end{document}7\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{gathered} u\frac{{\partial u}}{{\partial x}}+v\frac{{\partial u}}{{\partial y}}+\beta \left( {{u^2}\frac{{{\partial ^2}u}}{{\partial {x^2}}}+{v^2}\frac{{{\partial ^2}u}}{{\partial {y^2}}}+2uv\frac{{\partial u}}{{\partial x\partial y}}} \right)=m{A^2}{x^{2m - 1}}+Pr\frac{{{\partial ^2}u}}{{\partial {y^2}}} - {D_a}\left( {u+\beta v\frac{{\partial u}}{{\partial y}} - A{x^m}} \right) \hfill \\ \;\;+{M^2}\left[ {\left( {E+A{x^m}} \right) - \left( {u+\beta v\frac{{\partial u}}{{\partial y}}} \right)} \right]+Gr\theta cos\gamma . \hfill \\ \end{gathered}$$\end{document}8\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$u\frac{{\partial \theta }}{{\partial x}}+v\frac{{\partial \theta }}{{\partial y}}=\left( {1+P{e_\gamma }u+R} \right)\frac{{{\partial ^2}\theta }}{{\partial {y^2}}}+{M^2}{E_c}{\left( {u - A{x^m} - E} \right)^2}+Q\theta .$$\end{document} with boundary conditions9\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left\{ {\begin{array}{*{20}{c}} {u=0~,~~~~~v=\frac{{{M_b}}}{{Pr}}\frac{{\partial \theta }}{{\partial y}} - S,~~~~~\theta =0~~~~~~~~\mathrm{at}~~~y=0,} \\ {u \to A{x^m},~~~~~~\theta \to 1,~~~~~~~~~~~~~\mathrm{as}~~~y \to \infty .~} \end{array}} \right.$$\end{document} The imposed boundary conditions describe the physical behaviour of a wedge flow in the presence of melting and surface mass transfer effects. At the wall y=0, the condition u=0 represents the classical no-slip assumption, indicating that the fluid adheres to the surface due to viscous effects. The normal velocity condition incorporates both melting and suction/injection phenomena, where the term involving the melting parameter accounts for the fluid generated due to phase change at the surface, while the suction/injection parameter controls the mass flux across the boundary. Physically, suction S>0reduces the boundary layer thickness by drawing fluid toward the surface, whereas injection S<0 introduces additional fluid, leading to a thicker boundary layer. The thermal condition θ =0 indicates that the surface is held at the melting temperature. Far away from the surface \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$y \to \infty$$\end{document}, the velocity approaches the external wedge velocity \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$u=A{x^m}$$\end{document},which characterizes the Heimenz-type wedge flow and reflects the influence of the pressure gradient through the parameter \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left( m \right).$$\end{document} The temperature condition θ =1 ensures that the fluid asymptotically reaches the ambient temperature, indicating negligible thermal disturbance in the free stream. The dimensionless numbers involved are:\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{aligned} S & = \frac{{v_{w} L}}{{\alpha _{m} Pe^{{\frac{1}{2}}} }},~A = \frac{{cL^{{m + 1}} }}{{\alpha _{m} Pe}},~~Pr = \frac{\upsilon }{{\alpha _{m} }},~\beta = \frac{{\lambda u_{e} }}{L},~~M = \frac{{L\sigma B_{0} ^{2} }}{{\rho u_{e} }},~D_{a} = \frac{{\nu L}}{{Ku_{e} }},~E = \frac{{E_{0} }}{{u_{e} B_{0} }}, \\ Gr & = \frac{{Lg\beta _{T} \left( {T_{\infty } - T_{m} } \right)}}{{u_{e} ^{2} }},~M_{b} = \frac{{c_{p} \left( {T_{\infty } - T_{m} } \right)}}{{\left[ {L + C_{s} \left( {T_{m} - T_{0} } \right)} \right]}},~E_{c} = \frac{{u_{e} ^{2} }}{{c_{p} \left( {T_{\infty } - T_{m} } \right)}},~Q = \frac{{LQ_{0} }}{{\rho u_{e} c_{p} }}, \\ ~Pe_{\gamma } & = \frac{{\gamma du_{e} }}{{\alpha _{m} }},~R = \frac{{16\delta ^{*} T_{\infty }^{3} }}{{3kk^{*} }} \\ \end{aligned}$$\end{document} The dimensionless parameters appearing in formulation provide insight into the relative importance of various physical mechanisms governing the flow. The Prandtl number Pr represents the ratio of momentum diffusivity to thermal diffusivity and determines the relative thickness of velocity and thermal boundary layers. The wedge parameter A controls the strength of the external flow, while the suction/injection parameter S regulates mass transfer at the surface. The Deborah number β characterizes the elastic nature of the non-Newtonian fluid, with higher values indicating stronger fluid memory effects. The Hartmann number M quantifies the influence of the applied magnetic field, which generally resists fluid motion due to the Lorentz force. The Darcy number \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${D_a}$$\end{document} describes the permeability of the porous medium, where larger values correspond to reduced resistance to flow. The electric parameter E accounts for the contribution of the electric field to the flow dynamics. The Grashof number Gr represents the buoyancy force arising from temperature differences, promoting natural convection within the fluid. The melting parameter \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${M_b}$$\end{document} measures the intensity of the melting process at the surface, enhancing fluid motion and thermal transport near the wall. The Eckert number \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${E_c}$$\end{document} signifies the conversion of kinetic energy into internal energy through viscous dissipation. The heat source/sink parameter Q indicates whether heat is generated or absorbed within the fluid. Furthermore, the Péclet number for energy \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$P{e_\gamma }$$\end{document} expresses the relative importance of convective to conductive heat transfer, while the radiation parameter R accounts for thermal radiation effects, which become significant at high temperatures. Stream function Stream function is a mathematical tool that is used to make the study of incompressible two-dimensional flow simpler. It is very convenient as it automatically fulfills the continuity equation and maintains mass conservation in a hidden way. In boundary layer and similarity calculations, the stream function simplifies the number of dependent variables, converting PDEs into ODEs. The stream function approach is found to be very helpful in intricate viscoelastic flows such as those modeled by the UCM, wherein it is utilized to simulate near-surface flow behavior for surfaces such as plates or wedges46. Velocity components may be expressed through the stream function as:10\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$u=\frac{{\partial \psi }}{{\partial y}},~v=-\frac{{\partial \psi }}{{\partial x}}$$\end{document} After utilizing Eq. (10) to Eqs. (6–9), we get the following. \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left[ {\left( {\frac{{\partial \psi }}{{\partial y}}\frac{{{\partial ^2}\psi }}{{\partial x\partial y}} - \frac{{\partial \psi }}{{\partial x}}\frac{{{\partial ^2}\psi }}{{\partial {y^2}}}} \right)+\beta \left( {{{\left( {\frac{{\partial \psi }}{{\partial y}}} \right)}^2}\frac{{{\partial ^3}\psi }}{{\partial {x^2}\partial y}}+{{\left( {\frac{{\partial \psi }}{{\partial x}}} \right)}^2}\frac{{{\partial ^3}\psi }}{{\partial {y^3}}} - 2\frac{{\partial \psi }}{{\partial y}}\frac{{\partial \psi }}{{\partial x}}\frac{{{\partial ^3}\psi }}{{\partial x\partial {y^2}}}} \right)} \right]=m{A^2}{x^{2m - 1}}$$\end{document} 11\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left[ {\Pr \frac{{{\partial ^3}\psi }}{{\partial {y^3}}} - {D_a}\left( {\frac{{\partial \psi }}{{\partial y}} - \beta \frac{{\partial \psi }}{{\partial x}}\frac{{{\partial ^2}\psi }}{{\partial {y^2}}} - A{x^m}} \right)} \right]+{M^2}\left[ {\left( {E+A{x^m}} \right) - \left( {\frac{{\partial \psi }}{{\partial y}} - \beta \frac{{\partial \psi }}{{\partial x}}\frac{{{\partial ^2}\psi }}{{\partial {y^2}}}} \right)} \right]+Gr\theta cos\gamma ,$$\end{document} 12\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left( {\frac{{\partial \psi }}{{\partial y}}\frac{{\partial \theta }}{{\partial x}} - \frac{{\partial \psi }}{{\partial x}}\frac{{\partial \theta }}{{\partial y}}} \right)=\left( {1+P{e_\gamma }\frac{{\partial \psi }}{{\partial y}}+R} \right)\frac{{{\partial ^2}\theta }}{{\partial {y^2}}}+{M^2}{E_c}{\left( {\frac{{\partial \psi }}{{\partial y}} - A{x^m} - E} \right)^2}+Q\theta ,$$\end{document} 13\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$ \left\{ {\begin{array}{*{20}{c}} {\frac{{\partial \psi }}{{\partial y}}=0~,~~~~~\frac{{\partial \psi }}{{\partial x}}=S-\frac{{{M_b}}}{{Pr}}\frac{{\partial \theta }}{{\partial y}},~~~~~\theta =0~~~~~~~~\mathrm{at}~~~y=0,} \\ {\frac{{\partial \psi }}{{\partial y}} \to A{x^m},~~~~~~\theta \to 1,~~~~~~~~~~~~~\mathrm{as}~~~y \to \infty .~} \end{array}} \right.$$\end{document} One-argument Lie group scaling and similarity transformations The one-parameter Lie scaling method plays a crucial role in simplifying and analyzing complex fluid flow problems governed by nonlinear PDEs. In many boundary layer models, such as wedge flow with melting, electromagnetic effects, and non-Newtonian behavior, the governing equations are highly coupled and difficult to solve directly The Lie scaling methodology presents a single parameter continuous symmetry transformation40–45 and admits a reduction procedure of the initial PDEs into a collection of ODEs with suitable similarity variables. This simplifies the mathematical complexity of the problem but still captures the critical physics of the problem. This method is important in that it allows the identification of the hidden invariance properties of the governing equations, which makes the transformed system physically consistent. It offers a methodology and a strict method to obtain similarity solutions as opposed to making arbitrary assumptions. Practically, this simplification allows effective numerical calculation to be performed with tools such as the bvp4c solver of MATLAB, so we can analyse how several physical factors, such as magnetic field, melting, suction/injection and thermal radiation, affect the flow behavior. To enable the derivation of similarity transformations, a simplified version of the one-argument Lie group scaling transformation is proposed in the proposed model:14\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${x^*}=x{e^{\varepsilon {r_1}}},~{y^*}=y{e^{\varepsilon {r_2}}},{\psi ^*}=\psi {e^{\varepsilon {r_3}}},{\theta ^*}=\theta {e^{\varepsilon {r_4}}},{E^*}=E{e^{\varepsilon {r_5}}},~G{r^*}=Gr{e^{\varepsilon {r_6}}},~Pe_{\gamma }^{*}=P{e_\gamma }{e^{\varepsilon {r_7}}},$$\end{document} Here \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\varepsilon \ne 0$$\end{document} is a small argument of Lie groups. The set of the real numbers \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left( {{r_1},{r_2},{r_3},{r_4},~~{r_5},{r_6},{r_7}} \right)$$\end{document} transforms the coordinate system with the assumption that \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left( {0,0,0,0,0,0,0} \right)$$\end{document} does not belong to the set since element zero keeps the system unchanged. By using Eq. (14) in Eqs. (11)–(13), we get a new set of transformations. \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:\left[{e}^{\epsilon\:\left({r}_{1}+2{r}_{2}-2{r}_{3}\right)}\left(\frac{\partial\:{\psi\:}^{*}}{\partial\:{y}^{*}}\frac{{\partial\:}^{2}{\psi\:}^{*}}{\partial\:{x}^{*}\partial\:{y}^{*}}-\frac{\partial\:{\psi\:}^{*}}{\partial\:{x}^{*}}\frac{{\partial\:}^{2}{\psi\:}^{*}}{\partial\:{{y}^{*}}^{2}}\right)+\beta\:{e}^{\epsilon\:\left(2{r}_{1}+3{r}_{2}-3{r}_{3}\right)}\left({\left(\frac{\partial\:{\psi\:}^{*}}{\partial\:{y}^{*}}\right)}^{2}\frac{{\partial\:}^{3}{\psi\:}^{*}}{\partial\:{{x}^{*}}^{2}\partial\:{y}^{*}}+{\left(\frac{\partial\:{\psi\:}^{*}}{\partial\:{x}^{*}}\right)}^{2}\frac{{\partial\:}^{3}{\psi\:}^{*}}{\partial\:{{y}^{*}}^{3}}-2\frac{\partial\:{\psi\:}^{*}}{\partial\:{y}^{*}}\frac{\partial\:{\psi\:}^{*}}{\partial\:{x}^{*}}\frac{{\partial\:}^{3}{\psi\:}^{*}}{\partial\:{x}^{*}\partial\:{{y}^{*}}^{2}}\right)\right]$$\end{document} \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$=\left[ {\Pr {e^{\varepsilon \left( {3{r_2} - {r_3}} \right)}}\frac{{{\partial ^3}{\psi ^*}}}{{\partial {y^*}^{3}}} - {D_a}\left( {{e^{\varepsilon \left( {{r_2} - {r_3}} \right)}}\frac{{\partial {\psi ^*}}}{{\partial {y^*}}} - \beta {e^{\varepsilon \left( {{r_1}+2{r_2} - 2{r_3}} \right)}}\frac{{\partial {\psi ^*}}}{{\partial {x^*}}}\frac{{{\partial ^2}{\psi ^*}}}{{\partial {y^*}^{2}}} - A{e^{ - \varepsilon m{r_1}}}{x^{*m}}} \right)} \right]+m{A^2}{e^{ - \varepsilon \left( {2m - 1} \right)}}{x^{*\left( {2m - 1} \right)}}$$\end{document} 15\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$+{M^2}\left[ {\left( {{e^{ - \varepsilon {r_5}}}{E^*}+A{e^{ - \varepsilon m{r_1}}}{x^{*m}}} \right) - \left( {{e^{\varepsilon \left( {{r_2} - {r_3}} \right)}}\frac{{\partial {\psi ^*}}}{{\partial {y^*}}} - {e^{\varepsilon \left( {{r_1}+2{r_2} - 2{r_3}} \right)}}\beta \frac{{\partial {\psi ^*}}}{{\partial {x^*}}}\frac{{{\partial ^2}{\psi ^*}}}{{\partial {y^*}^{2}}}} \right)} \right]+{e^{\varepsilon \left( { - {r_4} - {r_6}} \right)}}G{r^*}{\theta ^*}cos\gamma ,$$\end{document} 16\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{gathered} {e^{\varepsilon \left( {{r_1}+{r_2} - {r_3} - {r_4}} \right)}}\left( {\frac{{\partial {\psi ^*}}}{{\partial {y^*}}}\frac{{\partial {\theta ^*}}}{{\partial {x^*}}} - \frac{{\partial {\psi ^*}}}{{\partial {x^*}}}\frac{{\partial {\theta ^*}}}{{\partial {y^*}}}} \right)={e^{\varepsilon \left( {2{r_2} - {r_4}} \right)}}\left( {1+{e^{\varepsilon \left( {{r_2} - {r_3} - {r_7}} \right)}}Pe_{\gamma }^{*}\frac{{\partial {\psi ^*}}}{{\partial {y^*}}}+R} \right)\frac{{{\partial ^2}{\theta ^*}}}{{\partial {y^*}^{2}}} \hfill \\ +{M^2}{E_c}{\left( {{e^{\varepsilon \left( {{r_2} - {r_3}} \right)}}\frac{{\partial {\psi ^*}}}{{\partial {y^*}}} - A{e^{ - \varepsilon m{r_1}}}{x^{*m}} - {e^{ - \varepsilon {r_5}}}{E^*}} \right)^2}+{e^{ - \varepsilon {r_4}}}Q{\theta ^*}, \hfill \\ \end{gathered}$$\end{document} with Boundary Conditions (BCs)17\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{gathered} \frac{{\partial {\psi ^*}}}{{\partial {y^*}}}=0,~~{e^{\varepsilon \left( {{r_1} - {r_3}} \right)}}\frac{{\partial {\psi ^*}}}{{\partial {x^*}}}~=S - \frac{{{M_b}}}{{Pr~}}~{e^{\varepsilon \left( {{r_2} - {r_4}} \right)}}\frac{{\partial {\theta ^*}}}{{\partial {y^*}}}~{e^{ - \varepsilon {r_4}}}{\theta ^*}~=~0,~~~\mathrm{as}~~{y^*}~=~0, \hfill \\ {e^{\varepsilon \left( {{r_2} - {r_3}} \right)}}\frac{{\partial {\psi ^*}}}{{\partial {y^*}}} \to A{e^{ - \varepsilon m{r_1}}}{x^{*m}},~~{e^{ - \varepsilon {r_4}}}{\theta ^*} \to 1,~~~~~\mathrm{as}~~{y^*} \to \infty . \hfill \\ \end{gathered}$$\end{document} After the introduction of Lie group transformation, for invariance in Eqs. (11)–(13), we have the following relations18\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${r_1}+2{r_2} - 2{r_3}=2{r_1}+3{r_2} - 3{r_3}= - \left( {2m - 1} \right){r_1}=3{r_2} - {r_3}={r_2} - {r_3}= - m{r_1}= - {r_5}= - {r_4} - {r_6},{\mathrm{~~}}$$\end{document}19\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${r_1}+{r_2} - {r_3} - {r_4}=2{r_2} - {r_4}=3{r_2} - {r_3} - {r_4} - {r_7}={r_2} - {r_3} - m{r_1}={r_2} - {r_3} - {r_5}= - {r_5} - m{r_1}={r_4},{\mathrm{~~}}$$\end{document}20\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${r_2} - {r_4}={r_1} - {r_3}=0,$$\end{document}21\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${r_2} - {r_3}= - m{r_1},$$\end{document}22\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${r_4}=0.$$\end{document} The present system admits multiple solutions for different values of the wedge parameter m, indicating the existence of non-unique flow behavior under varying pressure gradient conditions. To simplify the analysis and obtain physically meaningful and stable results, the case m=1 is selected. This choice corresponds to a stagnation-point flow configuration and allows for a more tractable mathematical formulation while still capturing the essential features of the problem. Moreover, it provides a convenient reference case for comparison with existing studies and ensures better numerical convergence. Solving the above Eqs. (18–22), simultaneously, the invariancy is obtained under the following condition \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left( {m=1} \right)$$\end{document}:23\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${r_2}={r_4}=0,{r_1}={r_3}={r_5}={r_6},{r_7}= - {r_1}.$$\end{document} Now, the transformed scaling transformations can be written as24\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${x^*}=x{e^{\varepsilon {r_1}}},~{y^*}=y,~{\psi ^*}=\psi {e^{\varepsilon {r_1}}},{\theta ^*}=\theta ,G{r^*}=Gr{e^{\varepsilon {r_1}}},{E^*}=E{e^{\varepsilon {r_1}}},{\mathrm{Pe}}_{\gamma }^{*}{\mathrm{=P}}{{\mathrm{e}}_\gamma }{e^{\varepsilon \left( { - {r_1}} \right)}}.$$\end{document} Applying the transformation provided by Eq. (24), we acquire the characteristic equation as25\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\frac{{d{x^*}}}{{{x^*}{r_1}}}=\frac{{d{y^*}}}{0}=\frac{{d{\psi ^*}}}{{{\psi ^*}{r_1}}}=\frac{{d{\theta ^*}}}{0}=\frac{{dG{r^*}}}{{G{r^*}{r_1}}}=\frac{{d{E^*}}}{{{E^*}{r_1}}}=\frac{{dPe_{\gamma }^{*}}}{{Pe_{\gamma }^{*}\left( { - {r_1}} \right)}}.$$\end{document} By following this procedure for all the variables, we have26\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\frac{{d{x^*}}}{{{x^*}{r_1}}}=\frac{{d{y^*}}}{0},$$\end{document} After cross multiplication and Integrate on both sides we have27\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\eta ={y^*},$$\end{document} The parametric equations are obtained with a similarity argument η after solving Eq. (25)28\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${y^*}=\eta ,~{\psi ^*}={x^*}f\left( \eta \right),~{\theta ^*}=\theta \left( \eta \right),G{r^*}={x^*}Gr\left( \eta \right),{E^*}={x^*}E\left( \eta \right),Pe_{\gamma }^{*}={\left( {{x^*}} \right)^{ - 1}}P{e_\gamma }\left( \eta \right).$$\end{document} Equations (15)–(17) were transformed into the following ODEs after implementing the above transformation given in (28)29\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{aligned} \left[ {\left( {f^{{\prime 2}} - ff^{\prime\prime}} \right) + \beta \left( {f^{2} f^{\prime\prime\prime} - 2ff^{\prime}f^{\prime\prime}} \right)} \right] & = \left[ {\Pr f^{\prime\prime\prime} - D_{a} \left( {f^{\prime} - \beta ff^{\prime\prime} - A} \right)} \right] + A^{2} \\ \;\; + M^{2} \left[ {\left( {E + A} \right) - \left( {f^{\prime} - \beta ff^{\prime\prime}} \right)} \right] + Gr\theta cos\gamma , \\ \end{aligned}$$\end{document}30\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$- f\theta ^{\prime}=\left( {1+P{e_\gamma }f^{\prime}+R} \right)\theta ^{\prime\prime}+{M^2}{E_c}{R_e}{\left( {f^{\prime} - A - E} \right)^2}+Q\theta .$$\end{document} The transformed boundary conditions are: \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$f^{\prime}=0,~~f~=~S - \frac{{{M_b}}}{{Pr{\mathrm{,}}}}\theta ^{\prime},~\theta =0~at~\eta =0$$\end{document} 31\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$f^{\prime} \to A,~\theta \to 1,~~~\mathrm{as}~~\eta \to \infty .$$\end{document} The intersecting physical quantities are the skin friction coefficient \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${{\boldsymbol{C}}_{\boldsymbol{f}}}$$\end{document}, and local Nusselt number \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${{\boldsymbol{N}}_{{{\boldsymbol{u}}_{\boldsymbol{x}}}}}$$\end{document} are shown below:32\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${C_f}=\frac{\mu }{{\rho {u_e}^{2}}}\frac{{\partial \bar {u}}}{{\partial \bar {y}}}{|_{y=0}}~,~{N_{{u_x}}}= - \frac{{x~{q_w}}}{{k\left( {{T_w} - {T_\infty }} \right)}}\left( {\frac{{\partial T}}{{\partial \bar {y}}}} \right){|_{y=0}}$$\end{document} By applying the above procedure of transforming in Eq. (32), the skin friction coefficient (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${C_f}$$\end{document}), and local Nusstle number (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${N_{{u_x}}}$$\end{document}) take the new form as: \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\frac{{{C_f}}}{{P{e^{ - 1/2}}}}=f^{\prime\prime}\left( 0 \right),$$\end{document} 33\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${N_{{u_x}}}~= - \left( {1+Re+P{e_\gamma }f^{\prime}\left( 0 \right)} \right)\theta ^{\prime}\left( 0 \right).$$\end{document} Solution methodology With our current formulation model, we have derived a set of nonlinear ODEs (29)–(30) and the associated boundary conditions (31), which are solved using the bvp4c scheme. We have employed the bvp4c method, a finite difference approach that yields a \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${C^1} -$$\end{document}continuous solution based on the Lobatto IIIA technique. We will now transform Eqs. (29)–(31) into a system of first-order equations by utilizing the MATLAB bvp4c method, applying it to the initial value problem. The resulting equations are as follows:34\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$f={y_1},{y_2}=y_{1}^{\prime }=f^{\prime},{y_3}=y_{2}^{\prime }=f^{\prime\prime},{y_4}=y_{3}^{\prime }=f^{\prime\prime\prime},\theta ={y_5},{y_6}=y_{5}^{\prime }=\theta ^{\prime},{y_7}=y_{6}^{\prime }=\theta ^{\prime\prime}$$\end{document} The new set of variables given in Eq. (34) transform the fundamental Eqs. (29)-(31), in the following form:35\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{gathered} \left[ {\left( {y_{2}^{2} - {y_1}{y_3}} \right)+\beta \left( {y_{1}^{2}{y_4} - 2{y_1}{y_2}{y_3}} \right)} \right]=\left[ {\Pr {y_4} - {D_a}\left( {{y_2} - \beta {y_1}{y_3} - A} \right)} \right] \hfill \\ \;\;+{A^2}+{M^2}\left[ {\left( {E+A} \right) - \left( {{y_2} - \beta {y_1}{y_3}} \right)} \right]+Gr{y_5}, \hfill \\ \end{gathered}$$\end{document}36\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$- {y_1}{y_6}=\left( {1+P{e_\gamma }{y_2}+R} \right){y_7}+{M^2}{E_c}{R_e}{\left( {{y_2} - A - E} \right)^2}+Q{y_5},$$\end{document} with the boundary conditions. \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$ya\left(2 \right)=0;~~ya\left( 1 \right)~=~S - \frac{{{M_b}}}{{Pr}}ya(5);~~ya\left( 4 \right)=~0$$\end{document} 37\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$yb\left( 2 \right) \to A;~yb\left( 4 \right) \to 1.$$\end{document} To achieve a continuous solution process, it is necessary to make assumptions about the initial guess standards for the conditions that are not available. These standards should be selected to facilitate asymptotic convergence concerning the boundary conditions. In our computations, we have set the error tolerance for achieving a precise result at 10–6. Validation To ensure the accuracy and reliability of the present numerical scheme, a validation study has been carried out for the skin friction coefficient represented by \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$f\prime\prime\left( 0 \right)$$\end{document}. For this purpose, the governing model is reduced to a simpler classical case by taking the Prandtl number Pr=1, Deborah number β =0 (corresponding to Newtonian fluid behavior), and neglecting the effects of magnetic field and porous medium by setting M=0 and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${D_a}=0.$$\end{document} Additionally, the wedge parameter is fixed at m=1, which corresponds to the well-known stagnation-point (Hiemenz) flow. Under these limiting conditions, the obtained numerical results show excellent agreement with previously reported results available in the literature52,53. This close agreement confirms the validity and robustness of the present numerical approach and ensures that the developed model and computational procedure are accurate for further analysis of the more complex physical problem. m \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${f^{\prime\prime}} \left( 0 \right)$$\end{document} Present valuesChakraborty and Janapatla52Ashwini and Eswara5311. 0.2325780031.232581.2326 m \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${f^{\prime\prime}} \left( 0 \right)$$\end{document} Present valuesChakraborty and Janapatla52Ashwini and Eswara5311. 0.2325780031.232581.2326 Discussion The Matlab function bvp4c is used to compute the numerical solution of the non-linear ODEs system given in Eqs. (29)–(30) and its boundary conditions given in (31). Furthermore, the graphical representation is organized consisting of magnetic argument \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$0.01 \leqslant M \leqslant 1$$\end{document}, Darcy number \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$0.01 \leqslant {D_a} \leqslant 1$$\end{document}, Deborah number \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$0.01 \leqslant \beta \leqslant 0.5$$\end{document}, Prandtl number \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$0.01 \leqslant Pr \leqslant 6.2$$\end{document}, suction argument \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$0.01 \leqslant S \leqslant 1.5$$\end{document}, Melting heat argument \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$0.1 \leqslant {M_b} \leqslant 1.5$$\end{document}, and Hiemenz argument \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$0.01 \leqslant A \leqslant 1.5$$\end{document} on velocity and thermal energy fields are illustrated. The results obtained are illustrated in Figs. 2, 3, 4 and 5, and their corresponding discussions are provided in the following sections. Figure 2 illustrates the impact of \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$M,{D_a},\beta ,$$\end{document} and Pr on the velocity field \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$f^{\prime}\left( \eta \right)$$\end{document}, respectively. It is observed that the velocity profile increases with an increase in the magnetic parameter M. This behavior indicates that, in the present configuration, the magnetic field contributes to the acceleration of the fluid rather than opposing it. Physically, this can occur in wedge flow configurations where the applied electromagnetic field interacts with the flow in such a way that the induced Lorentz force assists the fluid motion, particularly when additional effects such as electric fields or surface-driven forces are present. As a result, the momentum boundary layer is enhanced, leading to an increase in velocity. The influence of the Darcy number shows that the velocity increases with increasing \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${D_a}$$\end{document}. This is because higher values of \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${D_a}$$\end{document} correspond to greater permeability of the porous medium, which reduces resistance to fluid flow and allows the fluid to move more freely. Moreover, the velocity profile is enhanced with increasing Deborah number β. This reflects the elastic behavior of the UCM fluid, where higher β values indicate stronger memory effects. The stored elastic energy is released into the flow, reducing viscous resistance and promoting momentum transfer, thereby increasing the velocity distribution. In contrast, the Prandtl number exhibits an inverse relationship with the velocity profile. Larger values of correspond to lower thermal diffusivity, which enhances the dominance of viscous effects within the boundary layer. Consequently, the fluid motion is slightly suppressed, leading to a decrease in the velocity profile. The impacts of \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$M,{D_a},\beta ,$$\end{document} and Pr~on the thermal energy field \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\theta \left( \eta \right)$$\end{document} are presented in Fig. 4, respectively. The temperature profile is observed to increase with an increase in M. In this wedge flow configuration, a stronger magnetic field enhances the Lorentz force, which accelerates the fluid and promotes convective heat transport, thereby increasing the thermal energy within the boundary layer. Similarly, increasing the Darcy number \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${D_a}$$\end{document} results in a higher temperature distribution. A larger \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${D_a}$$\end{document} indicates a more permeable porous medium, allowing the fluid to flow more freely. This enhanced fluid motion strengthens convective heat transfer, leading to an elevated thermal field. The Deborah number β also positively influences the temperature profile. Higher β values correspond to stronger fluid elasticity, which improves momentum transport. This increased convective motion enhances the transfer of thermal energy, resulting in higher temperatures in the boundary layer. Interestingly, in this study, the thermal energy \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\theta \left( \eta \right)$$\end{document} increases with the Prandtl number. Physically, a larger Pr implies that the fluid has lower thermal diffusivity relative to momentum diffusivity. In the present wedge flow system with melting, suction/injection, and electromagnetic effects, the slower thermal diffusion causes heat to accumulate near the surface, thereby increasing the local temperature distribution and thickening the thermal boundary layer. The influence of \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$E,S,{M_b},$$\end{document} and A~on the thermal energy field \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\theta \left( \eta \right)$$\end{document}is depicted in Fig. 5, respectively. Figure 5 illustrates the effects of the electric parameter E, suction parameter S, melting parameter \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${M_b}$$\end{document}, and Hiemenz (wedge) parameter A on the thermal energy distribution. It is observed that the temperature profile increases with an increase in the electric parameter E. Physically, the applied electric field enhances the motion of charged particles within the fluid, which intensifies energy transport and promotes convective heat transfer, thereby increasing the thermal field. The influence of the suction parameter S shows that the temperature profile increases with increasing S in the present configuration. Although suction typically removes fluid from the boundary layer, in this case it stabilizes the flow and brings fluid particles closer to the heated surface. This enhances the thermal gradient near the wall and can lead to an increase in the temperature distribution within the boundary layer. Furthermore, the melting parameter \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${M_b}~$$\end{document}significantly enhances the thermal field. An increase in \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${M_b}$$\end{document} corresponds to stronger melting at the surface, which introduces additional thermal energy into the flow region. This process thickens the thermal boundary layer and elevates the overall temperature profile \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\theta \left( \eta \right)$$\end{document}. Finally, the Hiemenz (wedge) parameter A also contributes to an increase in temperature. Higher values of A strengthen the external flow velocity, which enhances fluid motion and convective heat transport. As a result, more heat is carried within the boundary layer, leading to an increase in the thermal energy distribution. Fig. 2Variation in the velocity profile \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$f^{\prime}\left( \eta \right)$$\end{document} under the influence of the Hartmann, Darcy, Deborah, and Prandtl numbers. Variation in the velocity profile \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$f^{\prime}\left( \eta \right)$$\end{document} under the influence of the Hartmann, Darcy, Deborah, and Prandtl numbers. Fig. 3Variation in the velocity gradient \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$f^{\prime}\left( \eta \right)$$\end{document} under the influence of the electric, suction, melting heat, and Hiemenz parameters. Variation in the velocity gradient \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$f^{\prime}\left( \eta \right)$$\end{document} under the influence of the electric, suction, melting heat, and Hiemenz parameters. Fig. 4Variation in the temperature profile \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\theta \left( \eta \right)$$\end{document} under the influence of the magnetic field, Darcy, Deborah, and Prandtl numbers. Variation in the temperature profile \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\theta \left( \eta \right)$$\end{document} under the influence of the magnetic field, Darcy, Deborah, and Prandtl numbers. Fig. 5Variation in the temperature profile \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\theta \left( \eta \right)$$\end{document} under the influence of the electric field, suction, melting heat, and Hiemenz numbers. Variation in the temperature profile \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\theta \left( \eta \right)$$\end{document} under the influence of the electric field, suction, melting heat, and Hiemenz numbers. Surface thermal energy transmission Optimization: RSM ~ CCD model The utilization of RSM with Central Composite Design (CCD) provides an effective methodology for the optimization of the thermal transport process by examining the interaction effects and influence of varied levels of several input factors simultaneously. Within the context of three variable input factors, CCD provides a sound experimental design for rigorous system investigation with the inclusion of factorial, axial, and center points, allowing for the comprehensive examination of the design space with a minimal number of experimental runs. This pivotal design approach increases the efficiency of experimental data gathering with consistent analytical in-depth evaluation47–51. RSM applies experimental results to formulate the second-order polynomial equation to determine the linear, interaction, and quadratic influences, thus facilitating the accurate mathematical modeling of the system responses with intensive accuracy. This approach not only helps to determine the significant factors that influence thermal energy transport efficiency but also helps to examine the mathematical relationships among these factors with lucid representation through the utilization of contour plots and three-dimensional surfaces. The complementarity of RSM and CCD provides a systematic, statistically refined method that has the potential to enhance the performance of a system by minimizing reliance solely on a trial-and-error technique. The complementarity of RSM and CCD is well recognized for its ability to provide a reliable method for evaluating the effects of various factors simultaneously, providing a coherent prediction tool for optimization. In the context of the current research work, the impact of melting heat, suction factor, and stagnation point intensity on Nusselt number is investigated using RSM. The design matrix along with the corresponding codes, as presented in Tables 1 and 2, form the basis for developing a complete quadratic polynomial equation, which allows for multi-variable modeling of the response surface by considering the respective variables along with their interactions.38\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$N{u_x}={\zeta _0}+{\zeta _1}{M_b}+{\zeta _2}S+{\zeta _3}A+{\zeta _4}M_{b}^{2}+{\zeta _5}{S^2}+{\zeta _6}{A^2}+{\zeta _{12}}{M_b}S+{\zeta _{13}}{M_b}A+{\zeta _{23}}AS.$$\end{document} Here, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\zeta _i},{\zeta _{ij}}$$\end{document} are the regression coefficients that must be computed using RSM utilizing 20 runs of experiments and 19 Degrees of Freedom (DOF). Choosing an experimental design is always advantageous for establishing correlations within RSM. In this study, the experimental arguments are \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${M_b},$$\end{document} S, and A. Table 1Design arguments with their levels for \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$N{u_x}$$\end{document} Experiment.DesignargumentsLevelsLow (-1)Mid (0)High (+ 1) \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${M_b}$$\end{document} 0.10.51 S 0.10.51 A 0.10.51 Table 1Design arguments with their levels for \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$N{u_x}$$\end{document} Experiment.DesignargumentsLevelsLow (-1)Mid (0)High (+ 1) \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${M_b}$$\end{document} 0.10.51 S 0.10.51 A 0.10.51 Design arguments with their levels for \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$N{u_x}$$\end{document} Experiment. Table 2Response surface with responses using CCD model.Exp. NoPoint typeReal standardsResponse variable \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${M_b}$$\end{document} S A \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$N{u_x}$$\end{document} 1Factorial points0.10.10.10.217606196210.10.11.50118630430.110.11.1312418224110.12.40394498050.10.110.225167927610.111.49942593870.1111.13046399881112.40170840290.10.50.50.62744716610Axial points10.50.51.902345892110.50.10.50.792315434120.510.51.697435823130.50.50.11.195106372140.50.511.19510637215Central points0.50.50.51.194102164160.50.50.51.195122162170.50.50.51.195122162180.50.50.51.195122162190.50.50.51.195122162200.50.50.51.195122162 Table 2Response surface with responses using CCD model.Exp. NoPoint typeReal standardsResponse variable \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${M_b}$$\end{document} S A \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$N{u_x}$$\end{document} 1Factorial points0.10.10.10.217606196210.10.11.50118630430.110.11.1312418224110.12.40394498050.10.110.225167927610.111.49942593870.1111.13046399881112.40170840290.10.50.50.62744716610Axial points10.50.51.902345892110.50.10.50.792315434120.510.51.697435823130.50.50.11.195106372140.50.511.19510637215Central points0.50.50.51.194102164160.50.50.51.195122162170.50.50.51.195122162180.50.50.51.195122162190.50.50.51.195122162200.50.50.51.195122162 Response surface with responses using CCD model. Model validity Improvement of the efficiency of the predictive model may, however, require the removal of non-significant variables. The backward elimination technique can be utilized for the removal of statistically non-significant variables to enhance the model by reducing the complexity of the model without changing the basic model and its interpretation. The efficiency of the proposed optimized model can then be tested using the coefficient and ANOVA tables to make a comparative estimation of improvement of the model by comparing the optimized model and the initial model. The summary of the results of the ANOVA table, which plays a pivotal part in the concepts of RSM, CCD, and DOE, can be found in Table 3. The principal role of the application of the ANOVA table is to determine the significance of the calculated regression coefficient, as presented in Table 4, to justify and ensure the efficiency and accuracy of the formulated model of the response. The terms presented in the regression table having p-standards below 0.05 are recognized as statistically important parameters, which consequently result in the retention of the model terms without reducing the accuracy of the predicted model. The graphical representation in Fig. 6 depicts the Nusselt number variations relative to its corresponding fitted values. The spread of points, along with the nearby histogram, shows that there is good alignment between the actual and modeled standards, hence validating the appropriateness of using a linear model. The graph effectively shows that it is reliable to model this system based on the Nusselt number. Figure 7(a–f) depicts the surface and contour plots that describe the interaction between two independent variables on the thermal energy transmission coefficient, as the third variable is kept at the middle level. These graphs demonstrate the change in the Nusselt number regarding the interaction of the testing parameters. In this respect, Fig. 7(a) and (b) indicate that an increase in the melting heat factor produces a significant increase in the response function, characterized by the slope of the contour levels and the growth of the surface plots. Figure 7(c, d) demonstrate how the stagnation argument A influences the Nusselt number, indicating that reduced standards of A and increased standards of \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${M_b}~$$\end{document}lead to a notable decline in the response surface. Finally, Figs. 7(e, f) illustrate how stagnation and suction variables affect the Nusselt number, further suggesting that higher standards of one variable S, combined with increased A, substantially enhance the response surface. The findings reveal that a notable enhancement in the response surface occurs when the melting heat argument is increased and the suction argument is elevated. Table 3ANOVA for \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$N{u_x}.$$\end{document}SourceDOFSSMSF-valueP-valueResultModel96.170.68607.017E + 05< 0.0001Significant \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${M_b}$$\end{document} 14.074.074.159E + 06< 0.0001Significant S 12.052.052.098E + 06< 0.0001Significant A 17.737E-077.737E-070.79140.3946Not Significant \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${M_b}S$$\end{document} 10.00000.000024.670.0006Significant \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${M_b}A$$\end{document} 10.00000.000014.830.0032Significant SA 19.675E-069.675E-069.900.0104Significant \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$M_{b}^{2}$$\end{document} 10.01330.013313598.37< 0.0001Significant \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${S^2}$$\end{document} 10.00670.00676894.88< 0.0001Significant \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${A^2}$$\end{document} 11.750E-071.750E-070.17900.6812Not SignificantResidual109.777E-069.777E-06Lack-of-Fit58.912E-061.782E-0610.310.0114Pure Error58.643E-071.782E-06Total196.17R-Squared = 100%Std. Dev. = 0.010Adj R-Squared = 100%Mean = 1.25Pre R-Squared = 100%C.V. = 0.0788Adeq Precision = 3126.6648Press = 0.0002 Table 3ANOVA for \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$N{u_x}.$$\end{document}SourceDOFSSMSF-valueP-valueResultModel96.170.68607.017E + 05< 0.0001Significant \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${M_b}$$\end{document} 14.074.074.159E + 06< 0.0001Significant S 12.052.052.098E + 06< 0.0001Significant A 17.737E-077.737E-070.79140.3946Not Significant \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${M_b}S$$\end{document} 10.00000.000024.670.0006Significant \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${M_b}A$$\end{document} 10.00000.000014.830.0032Significant SA 19.675E-069.675E-069.900.0104Significant \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$M_{b}^{2}$$\end{document} 10.01330.013313598.37< 0.0001Significant \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${S^2}$$\end{document} 10.00670.00676894.88< 0.0001Significant \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${A^2}$$\end{document} 11.750E-071.750E-070.17900.6812Not SignificantResidual109.777E-069.777E-06Lack-of-Fit58.912E-061.782E-0610.310.0114Pure Error58.643E-071.782E-06Total196.17R-Squared = 100%Std. Dev. = 0.010Adj R-Squared = 100%Mean = 1.25Pre R-Squared = 100%C.V. = 0.0788Adeq Precision = 3126.6648Press = 0.0002 ANOVA for \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$N{u_x}.$$\end{document} Table 4Coefficients of regression for \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$N{u_x}.$$\end{document}TermsCoefficientsP-standardsSignificant \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$N{u_x}$$\end{document} Intercept1.19511< 0.0001Yes \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${M_b}$$\end{document} 0.637669< 0.0001Yes S 0.452910< 0.0001Yes A 0.0002780.3946No \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${M_b}S$$\end{document} -0.0017360.0006Yes \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${M_b}A$$\end{document} -0.0013460.0032Yes SA -0.0011000.0104Yes \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$M_{b}^{2}$$\end{document} 0.069530< 0.0001Yes \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${S^2}$$\end{document} 0.049510< 0.0001Yes \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${A^2}$$\end{document} -0.0002520.6812No Table 4Coefficients of regression for \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$N{u_x}.$$\end{document}TermsCoefficientsP-standardsSignificant \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$N{u_x}$$\end{document} Intercept1.19511< 0.0001Yes \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${M_b}$$\end{document} 0.637669< 0.0001Yes S 0.452910< 0.0001Yes A 0.0002780.3946No \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${M_b}S$$\end{document} -0.0017360.0006Yes \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${M_b}A$$\end{document} -0.0013460.0032Yes SA -0.0011000.0104Yes \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$M_{b}^{2}$$\end{document} 0.069530< 0.0001Yes \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${S^2}$$\end{document} 0.049510< 0.0001Yes \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${A^2}$$\end{document} -0.0002520.6812No Coefficients of regression for \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$N{u_x}.$$\end{document} Fig. 6Residual plots for Nusselt Number. Residual plots for Nusselt Number. Sensitivity analysis The significance of this section is to discuss the sensitivity associated with a slight variation in arguments affecting efficiency in thermal energy transfer. The sensitivity analysis is conducted to identify how much a slight change in a particular input variable can affect the efficiency of thermal energy transfer. It is known as the sensitivity associated51 with the Nusselt number. The evaluation is carried out by calculating the partial derivatives of the Nusselt number with respect to the independent variables. The analysis identifies the most influential factors \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left( {{M_b},S,A} \right)$$\end{document}governing thermal energy transmission behavior. Such findings not only strengthen the knowledge of the transmission processes of thermal energy, but also help to enhance the existing thermal systems, along with the design of more efficient engineering applications. The values of the regression coefficients are shown in Table 4. A value of P-standard < 0.05 will be considered significant, and it will be retained; otherwise, it will be removed. Accordingly,\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$N{u_x}$$\end{document} is influenced by\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${M_b},S,$$\end{document} \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${M_b}A,$$\end{document} SA, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$M_{b}^{2},$$\end{document}. Consequently, the mathematical Eq. (38) may be rewritten as follows39\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{aligned} N{u_x} & =0.19511+0.637669{M_b}+0.452910S+0.069530M_{b}^{2}+0.049510{S^2} \\ & \;\;\; - 0.001346{M_b}S - 0.001736{M_b}A - 0.001100SA. \\ \end{aligned}$$\end{document} The partial derivatives are computed for the relevant and influential input variables, as detailed below:32\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left. {\begin{array}{*{20}{c}} {\frac{{\partial N{u_x}}}{{\partial {M_b}}}=0.637669+0.13906{M_b} - 0.001346A - 0.001736S,} \\ {\frac{{\partial N{u_x}}}{{\partial S}}=0.452910+0.09902S - 0.001346{M_b} - 0.001100A,} \\ {\frac{{\partial N{u_x}}}{{\partial A}}= - 0.001736{M_b} - 0.001100S.} \end{array}} \right\}$$\end{document} Table 5Sensitivity of \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${M_b}$$\end{document}and S when A = 0.5 on Nusselt number. \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${M_b}$$\end{document} S Sensitivity standards \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\frac{{\partial N{u_x}}}{{\partial {M_b}}}$$\end{document} \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\frac{{\partial N{u_x}}}{{\partial S}}$$\end{document} \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\frac{{\partial N{u_x}}}{{\partial A}}$$\end{document} 0.10.10.65070.4621-0.00030.50.65000.5017-0.000710.64920.5512-0.00130.50.10.70640.4616-0.00100.50.70570.5012-0.001410.70480.5507-0.002010.10.77590.4609-0.00180.50.77520.5005-0.002310.77430.5500-0.0028 Table 5Sensitivity of \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${M_b}$$\end{document}and S when A = 0.5 on Nusselt number. \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${M_b}$$\end{document} S Sensitivity standards \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\frac{{\partial N{u_x}}}{{\partial {M_b}}}$$\end{document} \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\frac{{\partial N{u_x}}}{{\partial S}}$$\end{document} \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\frac{{\partial N{u_x}}}{{\partial A}}$$\end{document} 0.10.10.65070.4621-0.00030.50.65000.5017-0.000710.64920.5512-0.00130.50.10.70640.4616-0.00100.50.70570.5012-0.001410.70480.5507-0.002010.10.77590.4609-0.00180.50.77520.5005-0.002310.77430.5500-0.0028 Sensitivity of \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${M_b}$$\end{document}and S when A = 0.5 on Nusselt number. Table 5 illustrates the sensitivity analysis, demonstrating how independent variables \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$({M_b},\,S,\,A)$$\end{document} influence the Nusselt number. This table systematically examines the Nusselt number’s response to changes in these arguments across various conditions, offering valuable insights into thermal performance and thermal energy transmission behavior. The partial derivative \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\frac{{\partial N{u_x}}}{{\partial {M_b}}}$$\end{document} ranges from 0.6507 to 0.7743 across all combinations of \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${M_b}$$\end{document} S, and A, representing an approximate increase of 18.98% in sensitivity as \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${M_b}$$\end{document} increases from 0.1 to 1.0, which quantitatively confirms that the melting heat argument is the most dominant factor influencing thermal energy transmission. The sensitivity standards \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\frac{{\partial N{u_x}}}{{\partial S}}$$\end{document} remains consistently in the range of 0.4609 to 0.5512, reflecting a relatively stable moderate influence with a variation of approximately 19.57%, indicating a proportional and steady contribution of the suction argument to the Nusselt number. The partial derivative \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\frac{{\partial N{u_x}}}{{\partial A}}$$\end{document} yields consistently negative values ranging from − 0.0003 to -0.0028, confirming that the Hiemenz argument suppresses thermal energy transmission, though its magnitude is significantly smaller, nearly 200 times less than that of \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${M_b}$$\end{document} quantitatively establishing it as the least influential among the three parameters. These insights provide crucial direction for improving thermal energy transmission systems through the adjustment of pertinent arguments. The accompanying table underscores the importance of sensitivity analysis in pinpointing critical elements that influence thermal performance, thereby aiding process optimization and boosting system efficiency. Fig. 7Contour\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left( {a,c,e} \right)$$\end{document} and 3D surface\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left( {b,d,f} \right)$$\end{document} Plots for Nusselt Number. Contour\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left( {a,c,e} \right)$$\end{document} and 3D surface\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left( {b,d,f} \right)$$\end{document} Plots for Nusselt Number. Concluding remarks The given study is a detailed examination of the thermal and momentum transport qualities of a UCM viscoelastic fluid that flows in a vertical wedge surface in the environment of porous medium. The originality of the piece consists in the concomitant nature of several interacting physical effects such as thermal radiation, melting effects, Joule heating, and EMHD forces, which are not often considered as a coherent entity. The model takes into consideration these coupled mechanisms together with realistic boundary conditions, which represent more accurate and realistic flow behaviors applicable to more advanced engineering and industrial processes. The combined method gives a better understanding of the multiplied effect of fluid elasticity, electromagnetic forces and heat transfer, hence the contribution to the current knowledge on non-Newtonian boundary layer flows. A one-argument Lie scaling transformation was found to reduce the governing PDEs to a series of nonlinear coupled ODEs that were then solved numerically by the MATLAB bvp4c solver. Also, sophisticated methods like RSM and sensitivity analysis were used to optimize the system arguments \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left( {{M_b},S,A} \right)$$\end{document} and determine their importance. This research offers a lot of knowledge and applicable solutions on how thermal performance can be enhanced in many industries such as energy systems, aerospace, and cooling technologies. The findings provide evidence-based suggestions on how to achieve the design and optimization of advanced thermal systems in practice by showing that precise modification of major factors can be used to improve thermal energy transmission. The main inferences made in this research are as follows: Velocity is growing for the magnetic field, porosity, and electric field argument.The Velocity profile is enhanced for Deborah number, suction argument, melting heat, and Hiemenz flow.Temperature field boosts for porosity, Prandtl number, melting heat, and Hiemenz flow.Temperature distribution enriches by the magnetic field and electric field argument.Utilizing the RSM-CCD method for optimization indicates that elevating \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${M_b}$$\end{document}is essential for achieving maximum thermal efficiency, whereas S and A provide additional improvements to the thermal energy transmission rate.The sensitivity analysis results indicate that controlling \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${M_b}$$\end{document}has the greatest potential to influence thermal performance outcomes, as evidenced by the highest sensitivity standards \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$~\frac{{\partial N{u_x}}}{{\partial {M_b}}}$$\end{document}. Velocity is growing for the magnetic field, porosity, and electric field argument. Velocity is growing for the magnetic field, porosity, and electric field argument. The Velocity profile is enhanced for Deborah number, suction argument, melting heat, and Hiemenz flow. The Velocity profile is enhanced for Deborah number, suction argument, melting heat, and Hiemenz flow. Temperature field boosts for porosity, Prandtl number, melting heat, and Hiemenz flow. Temperature field boosts for porosity, Prandtl number, melting heat, and Hiemenz flow. Temperature distribution enriches by the magnetic field and electric field argument. Temperature distribution enriches by the magnetic field and electric field argument. Utilizing the RSM-CCD method for optimization indicates that elevating \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${M_b}$$\end{document}is essential for achieving maximum thermal efficiency, whereas S and A provide additional improvements to the thermal energy transmission rate. Utilizing the RSM-CCD method for optimization indicates that elevating \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${M_b}$$\end{document}is essential for achieving maximum thermal efficiency, whereas S and A provide additional improvements to the thermal energy transmission rate. The sensitivity analysis results indicate that controlling \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${M_b}$$\end{document}has the greatest potential to influence thermal performance outcomes, as evidenced by the highest sensitivity standards \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$~\frac{{\partial N{u_x}}}{{\partial {M_b}}}$$\end{document}. The sensitivity analysis results indicate that controlling \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${M_b}$$\end{document}has the greatest potential to influence thermal performance outcomes, as evidenced by the highest sensitivity standards \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$~\frac{{\partial N{u_x}}}{{\partial {M_b}}}$$\end{document}. Limitations: The analysis is restricted to the UCM viscoelastic liquid model, which does not represent the behavior of other non-Newtonian liquids with different rheological properties.Absence of viscous dissipation in the analysis, which could limit the representation of certain physical effects.The problem focuses on a vertical wedge only, limiting its generalizability to other geometries such as cones, cylinders, or stretching sheets.Thermophysical properties (e.g., viscosity, thermal conductivity) are assumed constant, ignoring possible temperature-dependent variations.Slip conditions and radiative thermal energy transmission are modeled in simplified forms (e.g., linear slip, Rosseland approximation), which might not capture nonlinear or frequency-dependent behaviors. The analysis is restricted to the UCM viscoelastic liquid model, which does not represent the behavior of other non-Newtonian liquids with different rheological properties. The analysis is restricted to the UCM viscoelastic liquid model, which does not represent the behavior of other non-Newtonian liquids with different rheological properties. Absence of viscous dissipation in the analysis, which could limit the representation of certain physical effects. Absence of viscous dissipation in the analysis, which could limit the representation of certain physical effects. The problem focuses on a vertical wedge only, limiting its generalizability to other geometries such as cones, cylinders, or stretching sheets. The problem focuses on a vertical wedge only, limiting its generalizability to other geometries such as cones, cylinders, or stretching sheets. Thermophysical properties (e.g., viscosity, thermal conductivity) are assumed constant, ignoring possible temperature-dependent variations. Thermophysical properties (e.g., viscosity, thermal conductivity) are assumed constant, ignoring possible temperature-dependent variations. Slip conditions and radiative thermal energy transmission are modeled in simplified forms (e.g., linear slip, Rosseland approximation), which might not capture nonlinear or frequency-dependent behaviors. Slip conditions and radiative thermal energy transmission are modeled in simplified forms (e.g., linear slip, Rosseland approximation), which might not capture nonlinear or frequency-dependent behaviors. Real-world applications: The proposed study has profound applications in a wide range of engineering and industrial phenomena involving viscoelastic, non-Newtonian liquids interacting with thermal, magnetic, and electrical fields in porous media. In cooling a high-power electronic device and microchips, viscoelastic media are important in increasing heat dissipation to ensure the reliability of the system. The use of Joule heating and melting processes makes the model highly applicable to phase-change materials in thermal energy storage systems. Further, the characteristics of EMHD used play an important role in the design of MHD generators, microfluidic actuators, and liquid metal cooling technologies used in nuclear reactors and fusion devices.The UCM liquid model has wide application in the polymer processing industries, in extrusion and fiber spinning processes, particularly in applications in which external electromagnetic controls are involved in controlling the behaviour of liquids. The partial slip flow insights, as well as the melting insights at solid boundaries, also render the study applicable to materials engineering applications like coating flows, glass fiber production, and hot rolling of metals and polymers. In geothermal extraction, oil recovery and underground contaminant transport, where viscoelastic flows frequently dominate permeable rock formation, the porous medium representation is more relevant.Implementation of RSM and sensitivity analysis in this present study enhances its significance from theoretical system modeling to system design and optimization on a practical level. RSM enables the effective optimization of several physical arguments, leading to the creation of predictive models that can be useful towards enhancing thermal energy transmission rates at minimal computational expense. Sensitivity analysis fills the gap by determining the arguments with the greatest impact on flow and temperature behavior, an essential consideration in maximizing the reliability and performance of intricate systems such as electrothermal MEMS devices and polymer processing units. They also enable efficient process control of chemical reactors and production systems with viscoelastic materials, enabling engineers to predict how changes in input conditions affect operating efficiency. In cooling a high-power electronic device and microchips, viscoelastic media are important in increasing heat dissipation to ensure the reliability of the system. The use of Joule heating and melting processes makes the model highly applicable to phase-change materials in thermal energy storage systems. Further, the characteristics of EMHD used play an important role in the design of MHD generators, microfluidic actuators, and liquid metal cooling technologies used in nuclear reactors and fusion devices. In cooling a high-power electronic device and microchips, viscoelastic media are important in increasing heat dissipation to ensure the reliability of the system. The use of Joule heating and melting processes makes the model highly applicable to phase-change materials in thermal energy storage systems. Further, the characteristics of EMHD used play an important role in the design of MHD generators, microfluidic actuators, and liquid metal cooling technologies used in nuclear reactors and fusion devices. The UCM liquid model has wide application in the polymer processing industries, in extrusion and fiber spinning processes, particularly in applications in which external electromagnetic controls are involved in controlling the behaviour of liquids. The partial slip flow insights, as well as the melting insights at solid boundaries, also render the study applicable to materials engineering applications like coating flows, glass fiber production, and hot rolling of metals and polymers. In geothermal extraction, oil recovery and underground contaminant transport, where viscoelastic flows frequently dominate permeable rock formation, the porous medium representation is more relevant. The UCM liquid model has wide application in the polymer processing industries, in extrusion and fiber spinning processes, particularly in applications in which external electromagnetic controls are involved in controlling the behaviour of liquids. The partial slip flow insights, as well as the melting insights at solid boundaries, also render the study applicable to materials engineering applications like coating flows, glass fiber production, and hot rolling of metals and polymers. In geothermal extraction, oil recovery and underground contaminant transport, where viscoelastic flows frequently dominate permeable rock formation, the porous medium representation is more relevant. Implementation of RSM and sensitivity analysis in this present study enhances its significance from theoretical system modeling to system design and optimization on a practical level. RSM enables the effective optimization of several physical arguments, leading to the creation of predictive models that can be useful towards enhancing thermal energy transmission rates at minimal computational expense. Sensitivity analysis fills the gap by determining the arguments with the greatest impact on flow and temperature behavior, an essential consideration in maximizing the reliability and performance of intricate systems such as electrothermal MEMS devices and polymer processing units. They also enable efficient process control of chemical reactors and production systems with viscoelastic materials, enabling engineers to predict how changes in input conditions affect operating efficiency. Implementation of RSM and sensitivity analysis in this present study enhances its significance from theoretical system modeling to system design and optimization on a practical level. RSM enables the effective optimization of several physical arguments, leading to the creation of predictive models that can be useful towards enhancing thermal energy transmission rates at minimal computational expense. Sensitivity analysis fills the gap by determining the arguments with the greatest impact on flow and temperature behavior, an essential consideration in maximizing the reliability and performance of intricate systems such as electrothermal MEMS devices and polymer processing units. They also enable efficient process control of chemical reactors and production systems with viscoelastic materials, enabling engineers to predict how changes in input conditions affect operating efficiency.