Active vibration suppression of a magnetic–ball bearing hybrid supported rotor system Authors: Hang Shen, Chuan Zhao, Huachun Wu, Honglei Sha, Feng Sun, Junjie Jin Published: 2026 ABSTRACT AbstractThe vibration problem caused by milling is a key factor restricting high-precision and high-efficiency machining. Traditional passive vibration suppression methods are limited by fixed structural parameters and lack sufficient adaptability to dynamic operating conditions, making it difficult to achieve effective broadband vibration control. Magnetic bearings, with their non-contact characteristics and active controllability, provide a new idea for milling vibration suppression. To overcome these limitations, this paper proposes a novel hybrid magnetic-ball-supported flexible rotor system that combines active magnetic bearings with mechanical ball bearings, thereby achieving both controllable dynamic stiffness and stable rigid support. Based on the milling force model and the hybrid support rotor dynamics model, a coupled mathematical model is established, and the vibration suppression effect of the magnetic bearing on milling induced vibration is investigated by magnetic force regulation under PID control. Furthermore, milling force signals were generated using a simulation platform and applied to the rotor test bench to conduct numerical simulations and experimental validation. The results demonstrate that the proposed hybrid support strategy can significantly reduce milling-induced vibration amplitude, improve rotor dynamic stability, and enhance vibration suppression performance over a wide operating range. This study proposes a new hybrid vibration control scheme for high-speed, high-precision milling systems and provides a method for intelligent vibration reduction in advanced machining equipment.Keywords: Hybrid support, Magnetic bearings, Milling force, Vibration suppression, Rotor dynamicsSubject terms: Engineering, Materials science Introduction Vibration during milling negatively affects machining accuracy and tool life, thereby reducing overall machining efficiency1–3. Based on the differences in excitation mechanisms, these vibrations can be classified into two main categories: self-excited vibration and forced vibration4. Chatter originates from the internal coupling between the cutting process and the structural dynamics of the machine tool. The most common type, regenerative chatter, is a dynamic instability phenomenon formed by the interaction between the surface waviness left by a previous cutting edge and the cutting motion of the subsequent edge5. Forced vibration, in contrast, is primarily caused by periodic external excitations, such as the intermittent cutting of tool teeth and spindle unbalance6. These vibrations not only accelerate tool wear and reduce machining efficiency but also generate chatter marks on the workpiece surface, severely compromising machining accuracy and surface quality. Consequently, numerous scholars worldwide have conducted research on milling vibration suppression techniques. Currently, the primary techniques for milling vibration suppression fall into two categories: active suppression and passive suppression. Among these, passive suppression is a method that mitigates chatter by optimizing the inherent structural dynamics of the process system, rather than relying on external energy control7. The main suppression methods include tool holders equipped with tuned mass dampers8,9, variable-pitch/variable-helix end mills10, and specially designed fixtures. Although such methods are characterized by strong robustness and low cost, their vibration suppression performance is limited by the specific structural design, resulting in poor generality. In comparison, active suppression dynamically counteracts vibration by real-time sensing and applying opposing forces, offering high adaptability to complex working conditions and superior performance. Currently, piezoelectric actuators represent the predominant approach for implementing active suppression11–13. Piezoelectric actuators offer advantages in many vibration control applications due to their high-frequency response, high positioning accuracy, and substantial output force. However, in the specific operating conditions of rotor systems, these advantages can be limited, as the displacement of piezoelectric materials under a single excitation is typically very small, usually on the order of micrometers14. Therefore, integrated designs are often employed to achieve stroke amplification; however, they also introduce additional nonlinearities, which deteriorate control performance and complicate controller design. In response, many researchers have developed magnetically levitated motorized spindles for milling applications. These spindles utilize an active control mechanism to enhance machining accuracy and surface quality while simultaneously extending the service life of both the cutting tool and the spindle itself15–17. Although the magnetic bearings in a magnetically levitated electric spindle eliminate mechanical wear, their inherent dynamic stiffness is low, necessitating the use of relatively complex control algorithms to improve the overall stiffness of the spindle system. Cui G et al. proposed a novel control method based on an electromagnetic actuator (EMA) embedded in the tool holder, which enables control of chatter frequency18. Hans-Joachim K et al. proposed an adaptive spindle system incorporating an auxiliary electromagnetic bearing, and experimentally evaluated its static and dynamic performance up to 15,000 r/min; the results demonstrated that adaptive closed-loop control is effective in compensating tool deflection and vibration at the system eigenfrequencies19. Knospe C R By increasing the number of magnetic bearings in a magnetically levitated electro spindle, the dynamic stiffness of the spindle is realized through the active control of the magnetic bearings to improve the stability of the system during the cutting process, and the results show that the vibration problem induced by machining can be realized through the additional stiffness of the magnetic bearings20. Gourc E et al. proposed a method for identifying the stability of high-speed milling machining based on dynamic modeling of magnetically levitated electro spindles, and investigated the effect of several parameters of the controller on the stability of the system, and the results showed that the gain adjustment improves the stability of forced vibration during machining21. Tsai N C et al. employed active magnetic bearing (AMB) technology combined with fuzzy-logic algorithms and an adaptive self-tuning feedback loop to apply corresponding compensation forces, thereby balancing the dynamic cutting forces under different milling conditions and regulating spindle positional deviations22. These studies collectively demonstrate the effectiveness of electromagnetic control in improving spindle dynamic performance and machining stability. However, magnetically levitated spindle systems still suffer from relatively low dynamic stiffness, which may cause significant displacement under high-load cutting conditions and thereby compromise machining accuracy. Meanwhile, achieving both high stiffness and stable levitation usually depends on structurally complex control systems and highly demanding algorithms, which limits practical implementation. Therefore, this paper proposes a hybrid-supported rotor system that integrates magnetic bearings and rolling bearings, utilizing the magnetic bearings for active suppression of milling vibrations. In this study, a magnetic-ball bearing hybrid support rotor system is constructed by introducing a magnetic levitation bearing as an auxiliary support in the main support structure of a traditional rolling bearing and as an active regulating unit. Different from the system that completely relies on the magnetic levitation bearing to realize the load bearing, this hybrid support system serves as the basic load bearing unit, and the magnetic levitation bearing is used as the unit of adjustable dynamic stiffness and active damping. The rolling bearing provides stable support stiffness and reliable mechanical support, while the magnetic levitation bearing generates an adjustable force through closed-loop control, introducing a controllable increment in the equivalent stiffness and damping of the whole system. The hybrid support between the two allows the rotor system to gain the ability to actively regulate vibration characteristics while maintaining mechanical safety and structural stability. Based on this hybrid-supported rotor system, a dynamic model of a flexible rotor jointly supported by magnetic and rolling bearings is established and coupled with a dynamic milling force model. Subsequently, the vibration suppression effect achieved by magnetic intervention under different working conditions was evaluated by systematic analysis. Finally, a milling simulation excitation test was carried out on a test bed, and active vibration suppression was realized by a control system with integrated magnetic bearings. The results verify that the implementation of magnetic intervention in a hybrid supported rotor system can effectively suppress milling-induced vibration. Dynamic modeling of hybrid-supported rotor system Structure of the hybrid-supported rotor system This hybrid-bearing rotor system consists of a flexible rotor, a support system, a drive motor, and a cooling system. The support system comprises two pairs of angular contact ball bearings and two magnetic bearings, forming a hybrid-bearing structure that combines passive support with active control, as shown in Fig. 1. Structural diagram of the hybrid-supported rotor system. During the operation of the rotor system, the control of the magnetic bearings in the hybrid support is dynamically adjusted based on the rotor’s vibration status and operating conditions. When the rotor’s vibration is low, the magnetic bearings apply a smaller control force to achieve minimal vibration suppression; when external excitation increases or the amplitude of the rotor’s vibration grows, the control system enhances the magnetic force of the bearings, thereby adjusting the equivalent stiffness and damping of the support system to improve the system’s resistance to disturbances. This support configuration effectively eliminates the need for the large offset current required by magnetic bearings under long-term loading and the resulting heat generation issues, while also reducing the complexity associated with high-precision full-suspension control. Compared to mechanical bearing systems, it enhances active control capabilities; compared to pure magnetic bearing suspension systems, the proposed hybrid support configuration achieves an effective balance between control complexity and vibration suppression performance. Division of rotor system nodes and model development In order to accurately describe the dynamic behavior of the magnetic-ball hybrid supported flexible rotor system, a finite element dynamic model of the rotor is established based on the Timoshenko beam theory. Twenty-five nodes are selected along the rotor axis according to the finite element discretization rule, and the rotor is divided into 24 elastic units as shown in Fig. 2. Each unit has independent distributed mass and flexural deformation capacity. Schematic diagram of node division of magnetic-ball hybrid support rotor. For the s elastic unit, its dynamic equation can be expressed as follows: where is the displacement vector of the node, is the velocity vector of the node, and is the acceleration vector of the node; is the elastic unit cell mass matrix; is the elastic unit cell gyro matrix; is the elastic unit cell stiffness matrix; Ω is the rotor operating speed; is the elastic unit cell damping matrix. is the generalized force vector. In the rotor system, the accessory rotating components such as thrust disk have significant influence on the overall dynamic characteristics. In order to simplify the modeling and ensure the computational efficiency, this paper adopts the centralized mass method to load the rigid disk equivalently to the corresponding rotor node. Its dynamic equation can be expressed as: For the supporting part of the ball bearing, it is assumed that the contact deformation between the rolling element and the raceway satisfies the Hertz elastic contact theory, and the force of each rolling element remains consistent. The equivalent stiffness model of the rolling bearing is established as23: Where, is the bearing material coefficient; Z is the number of rolling elements; is the rolling element diameter; α is the contact angle; is the axial preload. Model of a magnetic levitation bearing system For the magnetic levitation bearing, since it is an electromechanical system, the stiffness and damping depend not only on the structural properties of the magnetic bearing but also on its control system. The magnetic bearing system employs differential control, where coil pairs 1 and 3 control the rotor’s motion in the Y-direction, and coil pairs 2 and 4 control its motion in the X-direction. The radial magnetic levitation bearing used in this study consists of eight magnetic poles, and its structural form and working principle are illustrated in Fig. 3. Vibration control is achieved using PID control; the control system block diagram is shown in Fig. 4. Working principle diagram of magnetic bearing. Schematic diagram of magnetic force intervention control for magnetic bearings. For the magnetic bearing system under PID differential control, the electromagnetic force model is established as: Where is the vacuum permeability; is the number of coil turns; A is the effective area of the magnetic poles; is the bias current; icx is the control current; is the airgap length; and is the airgap variation. In order to transform the complex nonlinear electromagnetic force model of magnetic bearings into a simple linear model near the operating point, so as to be able to apply linear control theory for system analysis, controller design and stability verification. Performing a Taylor expansion at the operating point where , and neglecting the higher-order terms, yields the linearized calculation formula for the electromagnetic force of the magnetic bearing: Where is the displacement stiffness coefficient and is the current stiffness coefficient. Their expressions are given by: This model is suitable for conditions involving small displacements and small disturbances; when the rotor displacement increases to a significant proportion of the air gap, nonlinear effects will cause the model’s accuracy to decline. For the hybrid support structure consisting of a magnetic levitation bearing and a passive bearing studied in this paper, the rotor displacement is small under normal operating conditions due to the constraining effect of the passive support; therefore, this linearized model is appropriate for the analysis in this paper. In order to clarify the regulating effect of the controller on the equivalent mechanical properties of the magnetic bearing, the generalized magnetic stiffness expression under closed-loop conditions is derived based on the transfer function of the PID controller, which is introduced into the current-displacement coupling relationship. On this basis, the system equations are transformed to the frequency domain form by Laplace transform, and the resulting complex stiffness is compared and analyzed with the classical spring-damped support model, so as to establish the correspondence between the control parameters and the equivalent stiffness and equivalent damping. For PID control, the transfer function can be expressed as The relationship between the current and displacement can be obtained as: By comparing it with the equivalent form of the spring-damper model in the frequency domain, the equivalent stiffness and equivalent damping of the PID-controlled magnetic bearings can be derived as follows: Thus, it can be concluded that by appropriately tuning the control gains , , and , the equivalent stiffness and damping characteristics of the magnetic bearings within the hybrid-supported rotor system can be effectively regulated. This enables dynamic adjustment of the magnetic force intervention capability, thereby modifying the interaction between the magnetic bearing and the rotor and influencing the overall vibration suppression performance and stability of the system. Milling force modeling To investigate the vibration suppression capability of magnetic bearings as auxiliary supports in the rotor system under milling forces, a milling force model is established. Based on the schematic diagram of symmetric milling with a four-flute end mill shown in Fig. 5, the tool-workpiece system is simplified into a two-degree-of-freedom vibration system in the X and Y directions24. In Fig. 5, O represents the tool center, denotes the tooth rotation angle, and and correspond to the tangential and radial forces, respectively. Diagram of four flute end mill machining. In the dynamic milling system, the workpiece is assumed to be infinitely stiff, and the overall milling system stiffness is thus attributed entirely to the tool. Due to the high axial stiffness of the rotor, the axial displacement of the tool is neglected in this study. For the two-degree-of-freedom spring-damper system of the tool shown in Fig. 5, the derived differential dynamic equation can be expressed as: Where and are the forces in the X and Y directions, respectively; m is the mass of the tool; x and y represent the displacements of the tool; and denote the damping coefficients of the tool system in the X and Y directions; and and are the stiffness coefficients of the tool system in the X and Y directions. In the milling process, the milling cutter teeth are not independently involved in cutting, but there is a certain phase difference, taking into account its regenerative effect, to find the dynamic cutting thickness is expressed as: Where is the instantaneous contact angle of the cutter tooth i. If the angular velocity of the rotor is , then ; is a judgment function, as shown in Equation. (12), which is used to determine whether or not the cutter tooth is in the cutting state. is the cutting-in angle of the cutter tooth, and is the cutting-out angle of the cutter tooth. The radial cutting force and tangential cutting force can be resolved into the X and Y directions of the coordinate system as follows: Where and are given by Eq. (14): Where is the cutting depth; is the cutting force coefficient ratio (); and and represent the radial and tangential milling force coefficients of the tool, respectively. The kinetic equation for milling force is obtained by substituting Equation. (14) into Equation. (13) and undergoing a triangular constant transformation: where , , and are denoted as: Dynamic model of the final hybrid support system The hybrid supported rotor system matrix is obtained by assembling the unit matrix according to the node correspondence, and its assembly form is shown in Fig. 2. The complete rotor system dynamics equation is obtained as: Where is the displacement vector; , , , and are the mass, damping, gyroscopic, and stiffness matrices of the rotor, respectively; and denote the stiffness and damping matrices of the ball bearings; and , , and represent the gravitational force, electromagnetic force of the magnetic bearings, and milling force, respectively. To describe the equivalent energy dissipation characteristics of the hybrid-supported rotor system, Rayleigh proportional damping is adopted in the simulation model. The damping matrix is expressed as: where and are the mass-proportional and stiffness-proportional damping coefficients, respectively. The damping coefficients are selected according to typical engineering values commonly used for flexible rotor systems to represent the combined effects of structural damping and bearing-related energy dissipation. No specific damping identification was performed in the experiment; the damping characteristics of the experimental system were primarily manifested through the inherent energy dissipation mechanisms in the actual rotor-bearing test bench, including material damping within the structure and energy losses during bearing contact. Vibration suppression for hybrid-supported rotors Milling force simulation excitation In the milling dynamic equation, the milling force coefficients are typically determined experimentally. However, based on the studies by Budak and Altintas, these coefficients can be regarded as constants when the workpiece and tool materials are specified25. Therefore, the milling force coefficients can be obtained by solving the simultaneous equations of the formula for the average26 milling force over one full rotation of the cutter and the formula for milling power. The milling forces were calculated using MATLAB. A four-tooth end mill with a diameter of 10 mm was selected, and the milling force coefficients were identified based on the average milling force method. A time-domain dynamic model of the machining system was established using the system parameters listed in Table 1. The Newmark-β numerical integration method was used to solve the system’s dynamic equations in the time domain. This method is widely used in structural dynamics and the analysis of flexible rotor systems, and it offers good numerical stability and computational accuracy. In the calculations, the parameters β = 1/4 and γ = 1/2 were selected, corresponding to the mean acceleration scheme, to ensure the algorithm’s unconditional stability. The time step is determined based on the rotor’s angular frequency, with a single rotation cycle uniformly discretized into 256 time steps. The total simulation duration is 60 cycles, ensuring accurate capture of the intermittent variations in milling forces and the tool engagement and disengagement processes. Table 1Milling dynamics parameters.ParameterSymbolValueUnitSpindle speed n 1,800rpmFeed per tooth f z 0.02mm/toothNumber of teeth z 4-Tangential Milling Force Coefficient K t 1.11 × 103N/mm²Radial Milling Force Coefficient K r 0.47 × 103N/mm²Tool diameter D 10mmRadial depth of cut (width) a e 10mmAxial depth of cut a p 1.5mm Milling dynamics parameters. To ensure the reliability of the numerical results, a time-step sensitivity analysis is conducted. The results confirm that further refinement of the time step leads to negligible changes in the system response, indicating that the numerical solution has achieved convergence. The simulation results are presented in Fig. 6, showing the milling force responses in the X and Y directions. Combined milling force of four-tooth end milling cutter. (a) X‑ directions, (b) Y- directions. As shown in Fig. 6, the milling forces exhibit distinct time-varying characteristics in the X and Y directions. During the initial stage of tool engagement, the system experiences a negative cutting force in the Y direction. As the engagement angle increases, the force in the Y direction gradually decreases, turns positive at a certain angle, reaches a positive peak, and then drops to zero as the tool exits the workpiece. In contrast, the milling force in the X direction undergoes only a single sign change during the penetration process. Overall, it first increases monotonically and then decreases monotonically; under the current cutting parameters, no positive milling force is observed. Overall, due to the intermittent cutting nature of multi-tooth cutting tools, the milling force varies periodically as the teeth rotate, exhibiting significant time-varying behavior and multi-harmonic characteristics. Its fundamental frequency is determined by the tooth passing frequency, superimposed with higher-order harmonic components. Therefore, this milling force can be regarded as a typical multi-frequency excitation source, which will have a significant impact on the vibration response and stability of the rotor system. Vibration suppression in a hybrid-supported rotor system under milling conditions Active vibration suppression for hybrid-supported rotor systems To analyze the vibration characteristics of the hybrid-supported rotor system under milling disturbance and to evaluate the suppression effect of magnetic bearing control, numerical simulations are conducted based on the established dynamic model. The milling force is calculated using the identified cutting parameters, with the spindle speed set to 1800 rpm, the axial depth of cut of 1.5 mm, and the feed per tooth of 0.02 mm. The resulting milling force is applied at the shaft end as an external excitation. The dynamic responses of the rotor system in the X and Y directions are then obtained under two conditions: with and without magnetic bearing control. The simulation results are presented in Fig. 7. Vibration response of a hybrid supported rotor system under milling loads. (a) X‑ directions, (b) Y- directions. As shown in Fig. 7, the vibration displacement response of the rotor after applying the simulated milling force can be observed. The figure indicates that the rotor’s vibration displacement exhibits periodic oscillations in both the X and Y directions, with a maximum value of 9.93 μm in the X-direction and 7.88 μm in the Y-direction. After magnetic force intervention via the magnetic bearings in the hybrid-supported system, the vibration displacement in both directions is reduced. Specifically, the displacement in the X-direction decreases from 9.93 μm to 7.57 μm, while in the Y-direction it decreases from 7.88 μm to 5.17 μm. The study demonstrates that the magnetic force control applied through the magnetic bearings in the hybrid-supported rotor system can effectively mitigate vibration issues induced by milling forces, with a more pronounced suppression effect observed in the Y-direction compared to the X-direction. To further demonstrate the advantages of the proposed method in vibration suppression, a conventional passive vibration damping system was introduced for comparison. This system, based on ball bearing supports, achieves vibration attenuation by increasing the equivalent structural damping and does not incorporate any active control forces or electromagnetic adjustment mechanisms. Comparison of active suppression with traditional method Traditional vibration reduction strategies primarily rely on passive structural design or additional damping elements to reduce system vibrations; they typically depend on pre-set parameters and are difficult to adjust in real time as rotational speed, load, and excitation frequency change. To further validate the effectiveness of the proposed active magnetic vibration reduction method, this paper compares it with conditions without vibration reduction and traditional passive vibration reduction methods; the results are shown in Fig. 8. Vibration suppression performance of the system at different rotational speeds. (a) X‑ directions, (b) Y- directions. As shown in Fig. 8, while traditional passive vibration damping methods can reduce vibration amplitude to some extent across the entire speed range, their damping effect is relatively limited. In particular, between 3,000 and 4,500 r/min, the displacement amplitude under traditional passive damping conditions increases significantly. This phenomenon is primarily due to the fact that traditional passive vibration damping strategies rely on structural natural parameters, making it difficult for them to adapt to changes in system dynamic characteristics caused by variations in rotational speed. In contrast, the active magnetic vibration control method maintains a low displacement level even at 3,000–4,500 r/min, indicating that this method can effectively regulate system vibrations in response to speed changes, thereby avoiding the vibration control failure that occurs with traditional passive strategies at specific speeds. Influence of magnetic force intervention on vibration suppression under different milling conditions Through the above analysis, it can be learned that the magnetic intervention of the magnetic bearing has a better suppression effect on the vibration caused by milling, but only studied the vibration suppression under the specific milling force, and did not analyze the vibration suppression effect under other milling conditions. Now, we consider some of the factors affecting the milling, and analyze the suppression of vibration displacement of the hybrid bearing rotor by the magnetic intervention of the magnetic levitation bearing in different working conditions. The intention is to analyze its wide-band vibration suppression capability. Analysis of vibration characteristics of the hybrid-supported rotor under different rotational speeds To analyze the effect of different rotational speeds on the vibration of the hybrid supported rotor system and the vibration suppression ability of magnetic bearing magnetic intervention under milling conditions, the depth of cut is taken as 1.5 mm, the feed rate of each tooth is 0.02 mm, and the rotational speed is increased from 1,000 rpm to 8,000 rpm, and the increment is taken to be 1,000 rpm for the vibration suppression capability of the hybrid supported rotor system under the two cases of magnetic intervention with magnetic bearings and non-magnetic bearing magnetic intervention. The vibration response of the rotor system is solved and the results are shown in Fig. 9. Rotor vibration displacement in all directions at different speeds. (a) X‑ directions, (b) Y- directions. As can be seen from Fig. 9, within the rotational speed range from 1,000 rpm to 8,000 rpm, the vibration displacement of the rotor in both the X and Y directions increases with rotational speed. Without magnetic force intervention from the magnetic bearings, the displacement rises from 8.15 μm to 12.26 μm in the X-direction and from 7.03 μm to 9.85 μm in the Y-direction. As the rotational speed increases, the vibration suppression by the magnetic intervention of the magnetic bearing reaches its maximum at 4,000 rpm, the effect is poor at 5,000 rpm, and the magnitude of vibration suppression is relatively good at other rotational speeds. This trend is mainly attributed to the interaction between the tooth-passing frequency (TPF) and the rotor’s dynamic characteristics. At 5,000 rpm, the TPF generated by the 4-tooth milling cutter approaches the first-order critical frequency of the rotor system, which may induce modal coupling and amplify the vibration response. In addition, the closed-loop magnetic bearing control may exhibit phase lag and reduced effective damping under this high-frequency excitation, thereby weakening the vibration suppression performance. After introducing magnetic force control from the magnetic bearings, the vibration displacement across the entire speed range is effectively suppressed. Compared with the condition without magnetic force, the displacement amplitude in the X-direction is reduced overall by approximately 1–3 μm, and in the Y-direction by about 2–4 μm. Furthermore, the vibration suppression effect remains more stable within the medium to high-speed range. Overall, with magnetic force intervention, the amplitude of vibration suppression displacement remains within a range of 2 to 3 μm across varying speeds, and no significant ineffective range was observed. This demonstrates that magnetic force intervention can maintain stable vibration suppression performance over a wide range of rotational speeds. Analysis of vibration characteristics of the hybrid-supported rotor under different cutting depth After considering the effect of rotational speed, it is found that the magnetic intervention of the magnetic bearing is most obviously suppressed at 3,000 rpm. During the milling process, another important parameter is the depth of cut, which directly affects the vibration characteristics of the rotor system. Now we analyze the effect of milling force on the rotor system under different cutting depths to investigate the vibration suppression ability caused by magnetic intervention under this working condition, take the rotational speed as 3,000 rpm, keep the feed quantity of each tooth unchanged and still 0.02 mm, change the size of the cutting depth from 1 mm to 2.5 mm, and then solve the vibration response of hybrid bearing rotor system in the two cases of magnetic intervention of magnetic bearings and magnetic intervention of non-magnetic bearings, and the results are presented in Fig. 10. Rotor vibration displacement in all directions at different cutting depth. (a) X‑ directions, (b) Y- directions. As shown in Fig. 10, within the cutting depth range from 1 mm to 2.5 mm, the vibration displacement of the rotor in both the X and Y directions increases with the cutting depth. Without magnetic force intervention from the magnetic bearings, the displacement rises from 4.78 μm to 26.13 μm in the X-direction and from 4.85 μm to19.15 μm in the Y-direction. With the increment of cutting depth, the vibration suppression effect of magnetic bearing magnetic intervention also increases gradually, and the suppression effect is good. After introducing magnetic force control from the magnetic bearings, the vibration displacement under each cutting depth condition is significantly suppressed. Compared with the non-magnetic condition, the overall reduction in the X-direction displacement ranges from approximately 1 μm to 4.5 μm, and in the Y-direction from about 2 μm to 4.5 μm. Moreover, the amplitude of vibration suppression provided by the magnetic force gradually increases with the cutting depth. This indicates that under larger milling forces, the equivalent stiffness and damping effects contributed by the magnetic bearings become more pronounced, effectively suppressing the vibration amplification caused by increased milling forces. Analysis of vibration characteristics of the hybrid-supported rotor under different feed rates Similarly, in addition to the rotational speed and depth of cut, the milling feed per tooth is also an important influence on the vibration characteristics of the rotor system, the same as above, take the rotational speed of 3,000 rpm, the depth of cut of 1.5 mm, the feed per tooth is gradually increased. The milling loads under different feeds are analyzed to investigate the vibration suppression effect of magnetic intervention under this condition, and the vibration response of the hybrid bearing rotor system is solved for the two cases of magnetic intervention of magnetic bearing and magnetic intervention of non-magnetic bearing, and the results are presented in Fig. 11. Rotor vibration displacement in all directions at different feed rates. (a) X‑ directions, (b) Y- directions. As shown in Fig. 11, as the feed per tooth, , increases from 0.01 mm to 0.05 mm, the vibration displacement amplitude of the rotor in both the X and Y directions shows a significant upward trend. Without magnetic force intervention from the magnetic bearings, the displacement amplitude in the X-direction rises sharply from approximately 3 μm to 50 μm, while in the Y-direction it increases from about 3 μm to 35 μm. This indicates that a larger feed rate substantially increases the milling force, thereby exacerbating the vibration response of the rotor system. With the incremental increase of the feed amount per tooth, the vibration suppression effect of magnetic bearing magnetic intervention also increases gradually, and the suppression effect is good. After introducing magnetic force control from the magnetic bearings, the vibration displacement under each feed rate condition is markedly suppressed. The suppression results demonstrate that this hybrid-supported system effectively reduces the vibration displacement amplitude across different feed rates, with a more pronounced suppression effect under high-feed conditions. Integrating the findings from the three operational conditions—rotational speed, cutting depth, and feed per tooth—it can be concluded that as the rotational speed increases or the cutting parameters (cutting depth and feed per tooth) become larger, the vibration displacement amplitude of the rotor in both the X and Y directions increases significantly. With the introduction of magnetic force control from the magnetic bearings, the vibration displacement under all three conditions is effectively suppressed. Furthermore, the magnitude of vibration suppression displacement increases with the magnitude of the milling force. The results confirm that magnetic force intervention from the magnetic bearings effectively suppresses the vibration displacement of the hybrid-supported rotor system under various operating conditions. Experimental investigation of vibration and its suppression under milling disturbance The experimental test bench of the magnetic-ball hybrid-supported rotor system used in this study is shown in Fig. 12. It consists primarily of two subsystems: the electrical control system and the mechanical system. The main components of the mechanical system include axial and radial magnetic bearings, angular contact ball bearings, a motor, the rotor, and mounting blocks. The electrical control system comprises eddy current displacement sensors, a frequency converter, power amplifiers, and a dSPACE platform. System diagram of the experimental platform for hybrid supported rotor system. The motor driving the rotor in this experiment is a three-phase permanent magnet synchronous motor with a rated power of 15 kW and a maximum speed of 30,000 rpm. The rotational speed was regulated by a Goodrive 350 series inverter. The specific process consists of configuring and debugging the control system of the magnetic ball hybrid supported rotor based on the dSPACE platform. The control module diagram was constructed in Simulink, from which dSPACE generated the real-time code. Parameter debugging and other operations were realized through an interactive monitoring interface developed by ControlDesk. The field experiment scene is shown in Fig. 13. Experimental setup of the magnetic-ball hybrid-supported rotor system. Figure 13 shows the basic experimental setup. Due to space constraints, the water cooler, inverter and other equipment are not shown. Where 1 is the magnetic-ball bearing hybrid supported rotor test rig, 2 is the dSPACE device, 3 is the driver, 4 is the eddy current sensor, and 5 is the power supply. In previous simulation analyses, the milling force model was established and the time-domain simulation of the milling force under different cutting conditions was performed. In order to further verify the simulation results and investigate the vibration damping effect of magnetic intervention, the milling force signals obtained from the simulation are fitted to obtain sinusoidal and square wave curves. In order to verify the effect of magnetic intervention on the vibration suppression of the rotor more clearly, the experimental selection of the speed of 1,800 rpm, by simulating the magnetic bearing in the X-direction to apply the sinusoidal fitting milling force, Y-direction to apply the square-wave fitting milling force for the simulation of loading, through the eddy-current displacement sensors, respectively, to measure the vibration displacement of the rotor system with and without the role of magnetic bearings magnetic force, the results are shown in Figs. 14. Vibration displacement response of rotor system under milling load. (a) X‑ directions, (b) Y- directions. As shown in Fig. 14, for the rotor system subjected to milling force loading, the vibration displacement with magnetic force intervention from the magnetic bearings is significantly reduced, indicating that the magnetic force effectively suppresses the vibration response induced by cutting forces. Without magnetic force intervention, the vibration displacement decreases from approximately 55 μm to about 45 μm in the X-direction, and from about 32 μm to around 20 μm in the Y-direction, which aligns with the trend observed in the simulation results. The experimental vibration response shown in Fig. 14 exhibits more pronounced high-frequency fluctuations than the simulated result in Fig. 7. This difference is mainly attributed to unavoidable disturbances in the experimental system, including residual rotor unbalance, assembly errors, sensor noise, bearing nonlinearities, and cutting-force fluctuations. In the present model, the governing equation primarily considers the coupled dynamics under cutting excitation and magnetic bearing control action, while the residual mass-unbalance excitation was not explicitly included. This is because the rotor was dynamically balanced prior to the experiment, and the remaining unbalance was relatively small and difficult to identify accurately in terms of magnitude and phase. Consequently, the simulation results exhibit a smoother dynamic response than the experimental measurements. Nevertheless, the overall variation trend and vibration suppression characteristics obtained from the simulation remain consistent with the experimental observations. Conclusion In this study, a hybrid rotor support system combining two magnetic bearings and two rolling bearings is proposed to suppress milling vibrations. A dynamic milling force model was established and incorporated into the rotor dynamics model as an external excitation term to analyze the vibration response under milling conditions. A PID-based magnetic force control strategy was employed to actively adjust the equivalent stiffness of the magnetic bearings, thereby suppressing rotor vibrations. Simulation results indicate that, under all studied operating conditions, magnetic intervention significantly reduced vibration displacement, with the suppression effect being more pronounced when the amplitude of the milling force was higher. To further validate the proposed approach, a simulated milling-force loading experimental platform was constructed to investigate vibration suppression under equivalent cyclic perturbations applied through the magnetic bearings. The experimental results were highly consistent with the simulation results, confirming that magnetic intervention can effectively suppress vibration. In the X- and Y-radial directions, the average vibration amplitude was reduced by approximately 20%, which verifies the effectiveness of the proposed model and control strategy. Nevertheless, this study has some limitations. Complex machining factors, including tool wear, nonlinear cutting effects, and transient cutting conditions, have not been fully accounted for. Furthermore, the study only examined PID-based control; the effects of axial dynamics, thermal effects, and long-term operational stability on the system require further investigation. Future work will focus on more realistic cutting conditions and advanced control strategies to further enhance the vibration damping performance of the hybrid-supported rotor system. Author contributions All authors contributed to the study of this paper. Hang Shen: Conceptualization, Methodology, Software, Writing-original draft. Chuan Zhao: Formal analysis, Visualization, Writing-review. Huachun Wu: Investigation, Honglei Sha: Supervision, Resources. Feng Sun: Resources. Junjie Jin: Visualization. Funding This research was funded by National Key Research and Development Plan of China under Grant (2024YFB3410002); in part by the Liaoning Provincial Science and Technology Plan Joint Program Key Research and Development Plan of Project under Grant (2025JH2/101800446). Data availability The data in this paper were obtained from real control experiments. Because it is laboratory test data, it is not publicly available; if there is a need for the data, please contact the corresponding author. Declarations Competing interests The authors declare no competing interests. Footnotes Publisher’s note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations. References Associated Data Data Availability Statement The data in this paper were obtained from real control experiments. Because it is laboratory test data, it is not publicly available; if there is a need for the data, please contact the corresponding author.