Experimental study on the reinforcement performance of unloading-damaged mudstone by microbial grouting Authors: Yan Guo, Huafeng Deng, Yongqi Chen, Wenxi Zhu, Zhenhua Li, Zhenhua Li, Zhenhua Li Published: 2026 ABSTRACT To address the structural deterioration and water-induced swelling of mudstone caused by unloading damage during foundation excavation, MICP and MICP-volcanic ash grouting reinforcement tests were conducted. Mudstone specimens with different unloading damage degrees were prepared through triaxial unloading tests. Combined with physical-mechanical tests and microstructural analyses, the swelling deformation, mechanical properties, and microscopic reinforcement mechanisms of unloading-damaged mudstone under different reinforcement methods were systematically investigated. The results show that unloading damage significantly reduces the strength of mudstone and enhances its swelling sensitivity. Both MICP and MICP-volcanic ash treatments can effectively suppress swelling deformation and improve strength. Specifically, MICP increased the residual strength by 7.41%–13.98% and the peak strength by 2.49%–6.34%, while MICP-volcanic ash increased them by 13.45%–20.61% and 5.36%–9.45%, respectively. Microstructural analysis shows that calcium carbonate mineralization products induced by MICP improve the structural integrity of mudstone by filling pores, sealing cracks, and enhancing interparticle cementation. The introduction of volcanic ash further promotes microbial retention, mineralization deposition, and densification of the pore-fracture structure, resulting in a better reinforcement effect than MICP alone. The results can provide a reference for the green reinforcement and stability improvement of unloading-damaged red-bed mudstone foundations. Introduction In recent years, with the continued expansion of infrastructure construction into red-bed areas, the long-term stability of red-bed mudstone foundations after excavation has attracted increasing attention [1,2]. Under natural conditions, red-bed mudstone generally exhibits a relatively intact primary structure. However, excavation disturbance disrupts the original in-situ stress equilibrium, resulting in significant unloading of the shallow rock mass, which in turn induces crack propagation, structural relaxation, and the development of local damage zones [3,4]. Meanwhile, under the repeated effects of rainfall infiltration and groundwater, the water-induced swelling of clay minerals in mudstone continues to develop, further aggravating structural deterioration and strength degradation of the rock mass, and readily leading to engineering problems such as foundation heave, deformation of retaining structures, and cracking of ancillary facilities [5,6]. Therefore, clarifying the deformation and instability mechanisms of red-bed mudstone under unloading damage and developing corresponding green and efficient reinforcement methods are of great theoretical significance and engineering value for ensuring the long-term service safety of foundations in red-bed areas. Considerable research has been conducted worldwide on deformation control and stability improvement of red-bed mudstone foundations, mainly through additive modification or grouting reinforcement to enhance the mechanical properties and water stability of mudstone [7]. Previous studies have shown that polyurea can strengthen the bonding between disintegrated mudstone particles and improve their strength stability under wetting-drying cycles [8]; organic acid-modified nano-colloidal silica-aluminate cement composite grouts can reduce the softening zone of mudstone and enhance its overall consolidation performance [9]; hydrophobic modifiers can improve the surface wettability and water absorption characteristics of weathered red-bed mudstone, thereby increasing its shear strength and structural stability [10]; and nano-silica sol grouting has shown good performance in sealing microcracks and improving the seepage resistance of mudstone [11]. Overall, existing studies have made substantial progress in enhancing mudstone strength, suppressing softening, and improving water resistance. However, most currently used modification materials are chemically synthesized or energy-intensive to produce, and may still impose environmental burdens during long-term service, which is not fully consistent with the requirements of green, low-carbon, and environmentally friendly engineering development. Therefore, the exploration of eco-friendly reinforcement technologies for red-bed mudstone foundations has become an important research direction in this field. Microbially induced calcium carbonate precipitation (MICP), as a rapidly developing biomineralization-based reinforcement technology in recent years, has received extensive attention due to its green, low-pollution, and sustainable characteristics [12,13]. This technique relies on urease-active microorganisms to decompose urea and induce the precipitation of calcium carbonate under suitable chemical conditions, thereby filling, bridging, and cementing pores and fractures within the medium [14,15]. Existing studies have demonstrated that MICP performs well in sand reinforcement, bearing-capacity improvement of foundations, and concrete crack repair [16,17]. In recent years, its application to rock fracture remediation has also made notable progress [18,19]. Some studies have further introduced MICP into mudstone improvement and found that calcium carbonate precipitates can form a certain cementation structure within mudstone pores, thereby improving its water stability and mechanical properties [20]. However, because mudstone is characterized by a complex pore structure, high clay mineral content, and strong water sensitivity, the survival of microorganisms as well as the deposition and spatial distribution of mineralization products within the mudstone are restricted to a certain extent. As a result, the reinforcement effect of conventional MICP still has room for further improvement. Volcanic ash is a natural porous material with abundant reserves and wide availability, and is characterized by low density, high porosity, and a large specific surface area. It has been widely used in building materials and ecological restoration [21,22]. In engineering materials, volcanic ash is commonly used as a cement admixture and concrete additive in self-compacting concrete and high-performance concrete systems [23]. In the environmental field, it can also be used for coral reef restoration and as a natural filter material and biological carrier for the adsorption of pollutants in water [24,25]. From the perspective of material functionality, the porous structure of volcanic ash is favorable for microbial attachment and growth, while its surface-active sites can provide favorable conditions for calcium carbonate nucleation and deposition. Therefore, volcanic ash has the potential to improve the formation efficiency and spatial distribution of mineralization products during the MICP process. On this basis, introducing volcanic ash into the MICP system to develop a volcanic ash-assisted biomineralization reinforcement method may provide a new approach for the green repair and stability improvement of unloading-damaged red-bed mudstone. Against this background, this study takes unloading-damaged mudstone obtained from a typical red-bed foundation excavation as the research object. Mudstone specimens with different damage degrees were prepared through triaxial unloading tests, and volcanic ash-assisted MICP grouting reinforcement tests were then carried out. Combined with lateral constrained swelling tests, triaxial compression tests, and scanning electron microscopy (SEM) observations, the deformation characteristics, mechanical response, and microstructural evolution of reinforced unloading-damaged mudstone were systematically analyzed. Furthermore, the reinforcement mechanism of volcanic ash-assisted MICP on unloading-damaged mudstone was revealed from both macroscopic mechanical behavior and microstructural evolution. The results of this study can provide a theoretical basis and technical support for the stability evaluation, green reinforcement design, and engineering treatment of unloading-damaged mudstone foundations in red-bed areas. Materials and Methods Materials Red-bed mudstone exposed during foundation excavation at a site in the Badong area was selected as the test material. After field sampling, the rock blocks were transported to the laboratory and processed into standard cylindrical specimens measuring 50 mm in diameter and 100 mm in height in accordance with relevant specifications. Specimens containing visible cracks were discarded. Based on density and P-wave velocity screening, the selected specimens had densities ranging from 2.68 to 2.71 g/cm3 and longitudinal wave velocities ranging from 3100 to 3300 m/s, indicating low variability and good homogeneity. The distributions of specimen density and wave velocity are shown in Fig 1. Sampling location of red-bed mudstone and the distributions of P-wave velocity and density. The mineralizing bacterium used in the MICP process was Bacillus cereus, which was independently isolated by the laboratory and is characterized by strong environmental adaptability, high activity, and excellent biomineralization capacity [26]. The bacterial concentration was measured using a UV spectrophotometer, and the OD600 value was determined to be 1.47. A cementation solution containing 1 mol/L calcium chloride and 1 mol/L urea was used to provide the calcium and nitrogen sources required for the MICP reaction. The volcanic ash used in the tests was obtained from a material factory in Yichang, Hubei Province, China, and appeared as reddish-brown granular particles. The volcanic ash particles were relatively fine, with particle sizes of less than 2 mm, and had a relatively large specific surface area. To analyze its main mineral composition, X-ray diffraction (XRD) tests were conducted on the volcanic ash, and the results are shown in Fig 2. As shown in the figure, the main crystalline mineral components of the volcanic ash included SiO₂ and Al₂O₃, indicating that it had certain mineral activity and potential conditions to serve as a carrier for microbial attachment and calcium carbonate nucleation. X-ray diffraction pattern of volcanic ash. Specimen preparation To ensure that the bacterial solution and cementation solution could fully infiltrate into the internal fractures of the specimens during the subsequent microbial grouting reinforcement process, a grouting hole with a diameter of 6 mm and a height of 100 mm was pre-drilled along the axial direction of each specimen, as shown in Fig 3. During the subsequent grouting process, the bottom of the grouting hole was first sealed, and then the grouting operation was carried out. Typical specimen photograph. Experimental scheme Unloading test scheme. The unloading tests were conducted using an RMT-150C rock mechanics testing system. Conventional triaxial compression tests were first performed at confining pressures of 5, 10, and 15 MPa. During the tests, the confining pressure was loaded to the target value at a rate of 0.05 MPa/s, after which the axial load was applied at a rate of 0.1 kN/s until specimen failure. The stress–strain curves of the mudstone specimens under different confining pressures were obtained, and the peak compressive strength of the specimens under a confining pressure of 5 MPa was determined. Based on the results of the conventional triaxial compression tests, confining pressure unloading tests were further conducted. In this study, the unloading degree refers to the degree of confining pressure unloading controlled by the stress path, rather than that calculated based on strain. It is defined as follows: where η is the unloading degree; σ₃⁰ is the initial confining pressure at the unloading point, which was taken as 5 MPa in this study; σ₃ⁱ is the target confining pressure after unloading; and σ₃ᶠ is the confining pressure corresponding to specimen failure under the conventional unloading path. According to the preliminary unloading failure test results, σ₃ᶠ was determined to be 1.6 MPa. Therefore, the target confining pressures of 2.6, 2.3, and 2.0 MPa corresponded to the designed unloading degrees of 70%, 80%, and 90%, respectively. Nine parallel specimens were prepared for each unloading degree, giving a total of 27 specimens, which were used for the subsequent microbial grouting reinforcement tests. The experimental stress path is shown in Fig 4. During the tests, the axial stress σ₁ and confining pressure σ₃ were first synchronously loaded to 5 MPa. The confining pressure was then kept constant, and the axial load was continuously applied at a rate of 0.1 kN/s. When the axial stress reached 80% of the peak strength under the confining pressure of 5 MPa, this point was defined as the unloading point. Subsequently, the axial load was kept constant, while the confining pressure was unloaded to the preset target values of 2.6, 2.3, or 2.0 MPa at a rate of 0.05 MPa/s. In this way, mudstone specimens with unloading degrees of 70%, 80%, and 90% were prepared. This procedure represents a confining pressure unloading test controlled by the stress path, rather than an unloading process calculated based on strain. Unloading test scheme (taking the 90% unloading level as an example). Reinforcement scheme Before each grouting cycle, the required bacterial suspension was taken from the conical flask and shaken well. Its bacterial concentration and urease activity were then measured. To ensure the effect of repeated grouting, the OD600 of the bacterial suspension was controlled at about 1.5 before each cycle. The concentration of the cementation solution was 1 mol/L. The volume ratio of bacterial suspension to cementation solution was 1:1. For the MICP-volcanic ash group, volcanic ash-loaded bacterial suspension was prepared by a pre-loading method. First, dried volcanic ash was weighed at a dosage of 100 g/L and mixed well with the bacterial suspension. The mixture was then placed in a shaking incubator at 30 °C and shaken at 100 r/min for 1 h. This allowed the bacteria to attach to the surface and pores of the volcanic ash particles. The obtained suspension was used as the volcanic ash-loaded bacterial suspension. This treatment helped the porous volcanic ash retain bacteria and provided attachment sites for later calcium carbonate nucleation and precipitation. Before specimen installation, a thin layer of petroleum jelly was applied evenly to the inner wall of the transparent mold. This was done to reduce friction between the specimen and the mold. Filter paper was also wrapped around the side and bottom surfaces of the specimen. After the specimen was placed in the mold, the mold opening was sealed. The PVC mold was then strengthened with cable ties, and the upper and lower ends were sealed with rubber stoppers. During grouting, the bottom rubber stopper was opened first. For the MICP group, 20 mL of bacterial suspension was injected into the specimen using a peristaltic pump at a flow rate of 5 mL/min. The specimen was then left to stand for 3 h. After that, 20 mL of cementation solution was injected at the same flow rate. For the MICP–volcanic ash group, 20 mL of volcanic ash-loaded bacterial suspension was injected at the same flow rate. After standing for 3 h, 20 mL of cementation solution was injected. To ensure comparability between the two reinforcement groups, the grouting rate, grouting volume, standing time, and number of cycles were kept the same. After each grouting cycle, the specimens were dried at 40 °C for 12 h. This step was used to reduce the water content of the specimens, promote the stable deposition of mineralization products in pores and fractures, and keep the initial state of the specimens relatively consistent before the next cycle. Since drying may affect the activity of residual microorganisms inside the specimens, fresh bacterial suspension or volcanic ash-loaded bacterial suspension was injected in each cycle. The OD600 and urease activity of the bacterial suspension were also measured before grouting to keep the microbial input conditions as consistent as possible. The above process was defined as one grouting cycle, and four cycles were carried out in total. A schematic diagram of the reinforcement device is shown in Fig 5, and typical reinforced specimens are shown in Fig 6. Schematic diagram of the microbial grouting reinforcement device. Typical unloading-damaged rock specimens after reinforcement. As shown in Fig 6, a few microcracks appeared on the surface of the mudstone after unloading damage. After microbial grouting repair, a large amount of calcium carbonate precipitate filled the surface cracks of the unloading-damaged mudstone specimens. This indicates that the repair effect was good. Swelling and mechanical properties of reinforced unloading-damaged mudstone Swelling characteristics. To investigate the effect of MICP reinforcement on the swelling behavior of unloading-damaged mudstone, lateral constrained swelling tests were conducted. During testing, mudstone specimens with different initial unloading damage degrees were placed in a sleeve together with stainless steel porous stones, and a dial indicator mounted on a magnetic stand was used to monitor specimen deformation. Pure water was then slowly injected around the specimen until the water level rose above the upper porous stone, after which the immersion swelling test was performed at room temperature. Specimen deformation was continuously monitored throughout the test. During the initial stage of immersion, readings were recorded every 10 min; after the deformation rate decreased, the recording interval was adjusted to 1 h. When the swelling rate remained below 0.001 mm for three consecutive hours, the swelling deformation was considered to have essentially reached a stable state. The lateral constrained swelling curves of unloading-damaged mudstone before and after reinforcement are shown in Fig 7, Fig 8, Fig 9. Lateral constrained swelling curves of unloading-damaged mudstone before and after reinforcement Unreinforced specimen. Lateral constrained swelling curves of unloading-damaged mudstone before and after reinforcement Unreinforced specimen MICP-reinforced specimen. Lateral constrained swelling curves of unloading-damaged mudstone before and after reinforcement Unreinforced specimen MICP-volcanic ash-reinforced specimen. Fig 7-9 shows that all specimens exhibited lateral constrained swelling under continuous water immersion, and the swelling evolution generally followed a three-stage pattern: a rapid growth stage (0–10 h), a slow growth stage (10–30 h), and a stabilization stage (after 30 h). The rapid increase at the initial stage was mainly associated with the swelling of clay minerals and the opening of pre-existing microcracks. Thereafter, the swelling rate gradually decreased as water migration within the specimen’s approached equilibrium, and the swelling strain became nearly stable after 30 h. For the unreinforced specimens, a pronounced swelling response was observed, and the final swelling strain increased with increasing unloading damage degree, indicating that unloading promoted the development of internal pores and cracks and enhanced the swelling sensitivity of mudstone. In the MICP-reinforced specimens, a similar stagewise evolution was observed, but the swelling curves were consistently lower than those of the unreinforced specimens under the same unloading condition, and the final swelling strain was significantly reduced. This suggests that MICP reinforcement can effectively suppress the swelling deformation of unloading-damaged mudstone. A further reduction in swelling strain was obtained after the incorporation of volcanic ash. Compared with the conventional MICP group, the swelling curves of the MICP-volcanic ash-reinforced specimens shifted downward more markedly, and the final swelling strain was further reduced. Overall, both MICP and MICP-volcanic ash reinforcement effectively reduced the lateral constrained swelling strain of unloading-damaged mudstone, with the latter showing a more pronounced inhibition effect. Mechanical properties To further analyze the mechanical properties of mudstone under unloading damage after MICP reinforcement, triaxial compression tests were carried out on the specimens before and after reinforcement. The corresponding stress-strain curves are shown in Fig 10, Fig 11, Fig 12. Triaxial compression stress-strain curves of specimens before and after reinforcement Triaxial compression stress-strain curves of specimens with 70% unloading. Triaxial compression stress-strain curves of specimens before and after reinforcement Triaxial compression stress-strain curves of specimens with 80% unloading. Triaxial compression stress-strain curves of specimens before and after reinforcement Triaxial compression stress-strain curves of specimens with 90% unloading. As shown in Fig 10-12, the triaxial compression stress–strain curves of mudstone specimens with different unloading damage degrees showed similar shapes. In general, the curves included the compaction stage, elastic stage, plastic stage, post-peak softening stage, and residual strength stage. As the unloading degree increased, both the peak strength and residual strength of the specimens decreased. This indicates that unloading damage promoted crack development and structural deterioration inside the mudstone, which weakened its bearing capacity. Under the same unloading condition, the stress–strain curves of the MICP-reinforced specimens were generally higher than those of the unreinforced specimens. Both the peak strength and residual strength increased, and the post-peak softening rate decreased. This shows that MICP reinforcement can effectively improve the mechanical behavior of unloading-damaged mudstone. Further comparison shows that the curves of the MICP–volcanic ash reinforced specimens were generally higher than those of the ordinary MICP-reinforced specimens. Their peak strength and residual strength were further improved, and their post-peak residual bearing capacity was also stronger. This indicates that the addition of volcanic ash further enhanced the filling and cementation effect of MICP, and improved the overall compactness and structural stability of the specimens. Overall, both MICP and MICP–volcanic ash reinforcement can effectively improve the mechanical properties of unloading-damaged mudstone. The MICP–volcanic ash method showed a better reinforcement effect. To further quantify the strength changes of mudstone before and after reinforcement, the peak strength and residual strength of each group were statistically analyzed. The results are shown in Fig 13, Fig 14 and Table 1. 10.1371/journal.pone.0350062.t001Table 1Statistical results of compressive strengths of specimens before and after reinforcement.Unloading damage degreeTreatment methodResidual strength/MPaCV of residual strength/%Increase rate of residual strength/%Peak strength/MPaCV of peak strength/%Increase rate of peak strength/%70%Unreinforced group11.204.09–28.092.08–70%MICP group12.033.817.4128.792.162.4970%MICP–volcanic ash group13.074.3116.6929.632.305.4880%Unreinforced group10.263.27–27.051.92–80%MICP group11.054.147.6927.912.293.1880%MICP–volcanic ash group11.642.8813.4528.501.825.3690%Unreinforced group9.514.82–25.082.33–90%MICP group10.845.1913.9826.672.566.3490%MICP–volcanic ash group11.473.9920.6127.452.279.45 Statistical results of compressive strengths of specimens before and after reinforcement. Triaxial compression stress-strain curves of specimens before and after reinforcement Residual strength. Triaxial compression stress-strain curves of specimens before and after reinforcement Peak strength. As shown in Fig 13−14 and Table 1, the residual strength and peak strength of the specimens in different groups showed some discreteness. The CV of residual strength was 2.88%−5.19%, and the CV of peak strength was 1.82%−2.56%. This indicates that the natural heterogeneity of mudstone, differences in unloading damage, and uneven distribution of mineralization products during grouting had some influence on the strength results. However, the overall trend was clear. Under the same unloading damage degree, the residual strength and peak strength of the MICP group and the MICP–volcanic ash group were both higher than those of the unreinforced group. The increase was more obvious in the MICP-volcanic ash group. This shows that the strength improvement after reinforcement was still consistent when specimen discreteness was considered. For the unreinforced specimens, as the unloading damage degree increased from 70% to 90%, the peak strength decreased from 28.09 MPa to 25.08 MPa, and the residual strength decreased from 11.20 MPa to 9.51 MPa. This indicates that greater unloading damage promoted the development of cracks and pores inside the mudstone. As a result, the bearing capacity and post-peak stability of the specimens were weakened. After MICP reinforcement, the residual strength increased by 7.41%−13.98%, and the peak strength increased by 2.49%−6.34%. After MICP–volcanic ash reinforcement, the residual strength increased by 13.45%−20.61%, and the peak strength increased by 5.36%–9.45%. These results show that both reinforcement methods improved the mechanical properties of unloading-damaged mudstone. The MICP–volcanic ash group showed a better improvement, especially in residual strength. This was mainly because the calcium carbonate precipitates induced by MICP could fill pores, seal cracks, and strengthen the cementation between particles. This improved the structural integrity of the specimens. In addition, the porous structure and large specific surface area of volcanic ash helped bacterial attachment, retention, and calcium carbonate nucleation. This further promoted the filling and cementation of mineralization products in the pores and cracks of mudstone. Therefore, the MICP-volcanic ash group showed a better strength improvement effect. Microstructure and reinforcement mechanism The swelling behavior and mechanical properties of mudstone with different degrees of unloading damage after MICP and MICP-volcanic ash grouting reinforcement were analyzed in the previous tests. To further reveal the reinforcement mechanism, this section analyzes the microstructural evolution of mudstone before and after reinforcement. The analysis is based on SEM observations, XRD phase analysis, and statistical results of surface porosity and fractal dimension obtained from SEM images. The reinforcement mechanisms of MICP and MICP-volcanic ash for unloading-damaged mudstone are also discussed. Microstructure and phase analysis Changes in macroscopic mechanical properties are usually closely related to the evolution of the rock microstructure. To further analyze the effect of MICP reinforcement on the microstructure of mudstone, SEM observations were carried out on mudstone specimens before and after reinforcement. The SEM images were also processed by binarization. The SEM images and binarized results of the unreinforced group, MICP group, and MICP–volcanic ash group are shown in Fig 15, Fig 16, Fig 17, Fig 18, Fig 19, Fig 20. The XRD phase analysis results of the specimens before and after reinforcement are shown in Fig 21. The changes in surface porosity and fractal dimension calculated from the SEM images are shown in Fig 22. SEM image and binarized image of the unreinforced mudstone specimen SEM image. SEM image and binarized image of the unreinforced mudstone specimen Binarized image. SEM image and binarized image of the mudstone specimen after MICP reinforcement SEM image. SEM image and binarized image of the mudstone specimen after MICP reinforcement Binarized image. SEM image and binarized image of the mudstone specimen after MICP-volcanic ash reinforcement SEM image. SEM image and binarized image of the mudstone specimen after MICP-volcanic ash reinforcement Binarized image. XRD phase analysis results of unloading-damaged mudstone before and after reinforcement. Variations in surface porosity and fractal dimension of unloading-damaged mudstone before and after reinforcement. As shown in Figs 15–22 (1) The surface structure of the unreinforced mudstone specimen was relatively loose. Some micropores, microcracks, and scattered mineral particles could be observed. The particles were mainly in primary contact, and the cementation between them was weak. This indicates that many pore and crack channels still existed in the mudstone after unloading damage. These channels could provide paths for water migration and conditions for clay minerals to absorb water and swell. After MICP reinforcement, many granular and clustered mineral deposits appeared on the specimen surface and between particles. Some deposits attached to the pores and cracks and formed bridging and cementation structures between particles. As a result, the original pores and cracks were partly filled and blocked. For the MICP–volcanic ash reinforced specimen, the deposited structure on the surface was more continuous and denser. The filling degree of pores and cracks was further improved. This shows that the porous structure and large specific surface area of volcanic ash helped bacterial retention and calcium carbonate nucleation. Therefore, the filling and cementation effects of mineralization products in pores and cracks were enhanced. (2) The XRD results further show that quartz, feldspar, and other original mineral peaks were mainly identified in the unreinforced mudstone specimen. After MICP reinforcement, the diffraction peaks related to calcium carbonate minerals, such as calcite, became stronger. This indicates that the microbial-induced mineralization process promoted the formation of calcium carbonate precipitates. Compared with the ordinary MICP group, the calcium carbonate-related peaks in the MICP–volcanic ash group were more obvious. This shows that the addition of volcanic ash helped promote the deposition of mineralization products. In addition, a small amount of cementitious products may have formed in the MICP–volcanic ash group. These products may have worked together with calcium carbonate precipitates to form a composite cementation structure. However, EDS point scanning or elemental mapping was not carried out in this study. Therefore, the specific composition of these cementitious products needs to be further verified by micro-area elemental analysis. (3) The quantitative image analysis results show that the surface porosity and fractal dimension of the unreinforced group were 22.1% and 1.78, respectively. After MICP reinforcement, the surface porosity decreased to 15.9%, and the fractal dimension decreased to 1.66. After MICP–volcanic ash reinforcement, the surface porosity further decreased to 12.6%, and the fractal dimension decreased to 1.59. Compared with the unreinforced group, the surface porosity of the MICP group and the MICP–volcanic ash group decreased by 28.1% and 43.0%, respectively. This indicates that both reinforcement methods effectively reduced pore development. The improvement was more obvious in the MICP–volcanic ash group. The decrease in fractal dimension shows that the complexity of the pore structure was reduced, and the connectivity of pores and cracks decreased. Therefore, the microstructure of the specimens became denser and more stable. In summary, MICP mainly filled pores, blocked cracks, and formed particle bridging through calcium carbonate precipitation. The addition of volcanic ash further enhanced bacterial retention, mineralization deposition, and composite cementation. This made the pore and crack structure of mudstone denser. The SEM observations, XRD phase analysis, surface porosity results, and fractal dimension results support each other. They show that both MICP and MICP–volcanic ash reinforcement can inhibit swelling deformation and improve mechanical properties by improving the microstructure of mudstone. The MICP–volcanic ash method showed a better reinforcement effect. Mechanism analysis of microbial grouting reinforcement for unloading-damaged mudstone Based on the above experimental results, the reinforcement effect of MICP on unloading-damaged mudstone is mainly reflected in the following two aspects. The grouting reinforcement mechanisms are illustrated in Fig 23 Schematic diagram of the microbial grouting reinforcement mechanism of mudstone. As can be seen from Fig 23: (1) During the MICP grouting process, urease-active microorganisms catalyze the hydrolysis of urea to generate carbonate ions, which then induce the precipitation of calcium carbonate in the presence of a calcium source. Because the surfaces of bacterial cells and extracellular polymers contain negatively charged functional groups such as hydroxyl, amino, amide, and carboxyl groups, the bacteria can adsorb Ca2+ and serve as nucleation sites for calcium carbonate crystals [27]. As the mineralization reaction proceeds, the generated calcium carbonate precipitates gradually attach to the surfaces of mudstone particles and deposit within pores, cracks, and seepage channels. Through filling, bridging, and cementation, these precipitates enhance interparticle connections and improve the structural integrity and bearing capacity of the specimens. (1) During the MICP grouting process, urease-active microorganisms catalyze the hydrolysis of urea to generate carbonate ions, which then induce the precipitation of calcium carbonate in the presence of a calcium source. Because the surfaces of bacterial cells and extracellular polymers contain negatively charged functional groups such as hydroxyl, amino, amide, and carboxyl groups, the bacteria can adsorb Ca2+ and serve as nucleation sites for calcium carbonate crystals [27]. As the mineralization reaction proceeds, the generated calcium carbonate precipitates gradually attach to the surfaces of mudstone particles and deposit within pores, cracks, and seepage channels. Through filling, bridging, and cementation, these precipitates enhance interparticle connections and improve the structural integrity and bearing capacity of the specimens. (2) Furthermore, calcium carbonate precipitates preferentially form and gradually accumulate in narrow crack zones, crack tips, and local seepage-concentrated areas, causing the original unloading-induced cracks to be continuously filled, refined, and sealed [28]. At the same time, the precipitates exhibit a certain degree of adsorption and bonding capacity toward mudstone particles and locally loose cementitious materials, thereby promoting the recommendation of crack surfaces, reducing crack connectivity and permeability, and ultimately realizing the repair and reconstruction of the internal structure of unloading-damaged mudstone. As a result, internal water migration pathways in the mudstone are inhibited, and the water-absorption swelling of clay minerals as well as the associated structural softening effects are correspondingly weakened. This is also the main reason why MICP can suppress the swelling deformation of mudstone and improve its mechanical properties. (2) Furthermore, calcium carbonate precipitates preferentially form and gradually accumulate in narrow crack zones, crack tips, and local seepage-concentrated areas, causing the original unloading-induced cracks to be continuously filled, refined, and sealed [28]. At the same time, the precipitates exhibit a certain degree of adsorption and bonding capacity toward mudstone particles and locally loose cementitious materials, thereby promoting the recommendation of crack surfaces, reducing crack connectivity and permeability, and ultimately realizing the repair and reconstruction of the internal structure of unloading-damaged mudstone. As a result, internal water migration pathways in the mudstone are inhibited, and the water-absorption swelling of clay minerals as well as the associated structural softening effects are correspondingly weakened. This is also the main reason why MICP can suppress the swelling deformation of mudstone and improve its mechanical properties. (3) Compared with conventional MICP grouting, MICP-volcanic ash grouting further introduces the physical filling effect and chemical enhancement effect of volcanic ash on the basis of biomineralization, and its mechanism is illustrated in Fig 13. Volcanic ash possesses a well-developed pore structure, a large specific surface area, and strong adsorption capacity. During the preparation of volcanic ash-loaded bacterial solution, it can adsorb and enrich a large number of microorganisms, thereby providing an attachment and protective carrier for bacteria, improving their retention capacity and survival time within cracks, promoting the continuous progress of the mineralization reaction, and increasing the yield of calcium carbonate precipitates. Meanwhile, volcanic ash particles themselves can also act as fine filling materials and enter relatively large pores and cracks within the mudstone, providing initial filling and scale refinement of the crack space and creating favorable conditions for the subsequent accumulation of calcium carbonate precipitates. In addition, under alkaline conditions, the active components in volcanic ash may undergo pozzolanic reactions to generate a small amount of C-S-H gel. This gel interweaves with calcium carbonate precipitates to form a composite cementation system, thereby further enhancing the structural stability of the crack zone. (3) Compared with conventional MICP grouting, MICP-volcanic ash grouting further introduces the physical filling effect and chemical enhancement effect of volcanic ash on the basis of biomineralization, and its mechanism is illustrated in Fig 13. Volcanic ash possesses a well-developed pore structure, a large specific surface area, and strong adsorption capacity. During the preparation of volcanic ash-loaded bacterial solution, it can adsorb and enrich a large number of microorganisms, thereby providing an attachment and protective carrier for bacteria, improving their retention capacity and survival time within cracks, promoting the continuous progress of the mineralization reaction, and increasing the yield of calcium carbonate precipitates. Meanwhile, volcanic ash particles themselves can also act as fine filling materials and enter relatively large pores and cracks within the mudstone, providing initial filling and scale refinement of the crack space and creating favorable conditions for the subsequent accumulation of calcium carbonate precipitates. In addition, under alkaline conditions, the active components in volcanic ash may undergo pozzolanic reactions to generate a small amount of C-S-H gel. This gel interweaves with calcium carbonate precipitates to form a composite cementation system, thereby further enhancing the structural stability of the crack zone. (4) In summary, MICP mainly improves the internal structure of unloading-damaged mudstone through calcium carbonate precipitation, which fills pores, seals cracks, and cements particles. The introduction of volcanic ash further strengthens bacterial retention, precipitate accumulation, and composite cementation effects, enabling the reinforced mudstone to form a denser and more stable microstructure, and ultimately achieving more effective suppression of swelling deformation and further improvement in mechanical properties. (4) In summary, MICP mainly improves the internal structure of unloading-damaged mudstone through calcium carbonate precipitation, which fills pores, seals cracks, and cements particles. The introduction of volcanic ash further strengthens bacterial retention, precipitate accumulation, and composite cementation effects, enabling the reinforced mudstone to form a denser and more stable microstructure, and ultimately achieving more effective suppression of swelling deformation and further improvement in mechanical properties. Discussion This study confirmed the feasibility of using volcanic ash–MICP to reinforce unloading-damaged mudstone. The porous structure of volcanic ash provides sites for bacterial attachment and calcium carbonate nucleation. Together with MICP mineralization products, it helps fill pores, block cracks, and cement particles. Thus, it improves the resistance of mudstone to swelling deformation and strength deterioration. However, volcanic ash may also improve the mudstone structure through physical filling and potential reactive effects. Therefore, the reinforcement effect of the MICP–volcanic ash group should be regarded as the combined result of volcanic ash and MICP mineralization. Their individual contributions need further quantitative evaluation through control tests. In this study, specimens were dried at 40 °C for 12 h after each grouting cycle. This step reduced water content, promoted stable mineral deposition, and provided similar initial conditions for the next cycle. Fresh bacterial suspension or volcanic ash-loaded bacterial suspension was injected in each cycle, and OD600 and urease activity were controlled before grouting. However, the survival rate and urease activity of residual bacteria after drying were not measured. Thus, the effect of drying on later mineralization remains uncertain. Future studies should examine bacterial survival, urease activity, and calcium carbonate production under different drying temperatures and times. Further research should focus on control tests, process optimization, and field verification. A volcanic ash-only group should be added to distinguish the effects of physical filling, nucleation promotion, and MICP mineralization. Different volcanic ash dosages, particle sizes, and slurry concentrations should also be tested. For field application, the injectability and diffusion of bacterial suspension, cementation solution, and volcanic ash particles should be studied under different grouting pressures, borehole spacings, grouting volumes, and cycle numbers. In the laboratory, a 6 mm central grouting hole was used to improve slurry penetration. In the field, however, fracture connectivity and seepage paths are more uneven. For low-permeability or weakly fractured mudstone, pre-wetting, local pretreatment, and staged low-pressure cyclic grouting may improve slurry diffusion and reduce the risk of new crack growth. Finally, field tests are needed to verify the reinforcement effect, long-term durability, and environmental adaptability of volcanic ash-MICP under real engineering conditions. This would support its application in the green reinforcement of red-bed mudstone foundations. Conclusions In this study, MICP and MICP–volcanic ash grouting tests were carried out on unloading-damaged mudstone. Lateral confined swelling tests, triaxial compression tests, SEM observations, XRD phase analysis, and quantitative image analysis were used to study the swelling behavior, mechanical response, and reinforcement mechanism of the specimens. The main conclusions are as follows: (1) Unloading changed the pore and crack structure of mudstone and caused deterioration in mechanical properties and water stability. As the unloading degree increased from 70% to 90%, cracks and pores developed gradually. The peak strength and residual strength decreased, while swelling deformation under water immersion increased. This shows that unloading damage is an important factor causing strength reduction and higher swelling sensitivity of mudstone. (1) Unloading changed the pore and crack structure of mudstone and caused deterioration in mechanical properties and water stability. As the unloading degree increased from 70% to 90%, cracks and pores developed gradually. The peak strength and residual strength decreased, while swelling deformation under water immersion increased. This shows that unloading damage is an important factor causing strength reduction and higher swelling sensitivity of mudstone. (2) Both MICP and MICP-volcanic ash grouting effectively reduced the swelling deformation of unloading-damaged mudstone and improved its peak and residual strengths. Compared with the unreinforced specimens, the residual strength of the MICP-reinforced specimens increased by 7.41%−13.98%, and the peak strength increased by 2.49%−6.34%. For the MICP-volcanic ash reinforced specimens, the residual strength increased by 13.45%−20.61%, and the peak strength increased by 5.36%−9.45%. Although some discreteness existed among the specimens, the strength improvement after reinforcement was consistent. The MICP-volcanic ash group showed the best reinforcement effect. (2) Both MICP and MICP-volcanic ash grouting effectively reduced the swelling deformation of unloading-damaged mudstone and improved its peak and residual strengths. Compared with the unreinforced specimens, the residual strength of the MICP-reinforced specimens increased by 7.41%−13.98%, and the peak strength increased by 2.49%−6.34%. For the MICP-volcanic ash reinforced specimens, the residual strength increased by 13.45%−20.61%, and the peak strength increased by 5.36%−9.45%. Although some discreteness existed among the specimens, the strength improvement after reinforcement was consistent. The MICP-volcanic ash group showed the best reinforcement effect. (3) SEM observations, XRD phase analysis, and quantitative image analysis showed that calcium carbonate precipitates formed during MICP could fill pores, block cracks, bridge particles, and improve cementation. These effects improved particle contact, structural compactness, and overall stability. After MICP and MICP–volcanic ash reinforcement, both surface porosity and fractal dimension decreased. This indicates that the reinforcement reduced pore development and the complexity of the pore-crack structure. The improvement was more obvious in the MICP–volcanic ash group. (3) SEM observations, XRD phase analysis, and quantitative image analysis showed that calcium carbonate precipitates formed during MICP could fill pores, block cracks, bridge particles, and improve cementation. These effects improved particle contact, structural compactness, and overall stability. After MICP and MICP–volcanic ash reinforcement, both surface porosity and fractal dimension decreased. This indicates that the reinforcement reduced pore development and the complexity of the pore-crack structure. The improvement was more obvious in the MICP–volcanic ash group. (4) The reinforcement of unloading-damaged mudstone by MICP is mainly a crack repair and structural reconstruction process based on calcium carbonate mineralization. The addition of volcanic ash further promoted bacterial retention, mineral deposition, and pore-crack filling. It may also form composite cementation together with mineralization products. These effects helped reduce water migration and water-induced swelling softening, and improved both deformation control and mechanical properties. However, the separate contributions of volcanic ash alone and the combined MICP-volcanic ash effect still need to be quantified by further control tests. (4) The reinforcement of unloading-damaged mudstone by MICP is mainly a crack repair and structural reconstruction process based on calcium carbonate mineralization. The addition of volcanic ash further promoted bacterial retention, mineral deposition, and pore-crack filling. It may also form composite cementation together with mineralization products. These effects helped reduce water migration and water-induced swelling softening, and improved both deformation control and mechanical properties. However, the separate contributions of volcanic ash alone and the combined MICP-volcanic ash effect still need to be quantified by further control tests. 6 Jun 2026 Dear Dr. Zhu, Thank you for submitting your manuscript to PLOS ONE. After careful consideration, we feel that it has merit but does not fully meet PLOS ONE’s publication criteria as it currently stands. Therefore, we invite you to submit a revised version of the manuscript that addresses the points raised during the review process. You will see from the referees' comments that additional information needs to be provided, and we ask that this be provided, before we consider you manuscript further. Please submit your revised manuscript by Aug 05 2026 11:59PM. If you will need more time than this to complete your revisions, please reply to this message or contact the journal office at plosone@plos.org. When you're ready to submit your revision, log on to https://www.editorialmanager.com/pone/ and select the 'Submissions Needing Revision' folder to locate your manuscript file. A letter that responds to each point raised by the academic editor and reviewer(s). You should upload this letter as a separate file labeled 'Response to Reviewers'. A letter that responds to each point raised by the academic editor and reviewer(s). You should upload this letter as a separate file labeled 'Response to Reviewers'. A marked-up copy of your manuscript that highlights changes made to the original version. You should upload this as a separate file labeled 'Revised Manuscript with Track Changes'. A marked-up copy of your manuscript that highlights changes made to the original version. You should upload this as a separate file labeled 'Revised Manuscript with Track Changes'. An unmarked version of your revised paper without tracked changes. You should upload this as a separate file labeled 'Manuscript'. An unmarked version of your revised paper without tracked changes. You should upload this as a separate file labeled 'Manuscript'. If you would like to make changes to your financial disclosure, please include your updated statement in your cover letter. Guidelines for resubmitting your figure files are available below the reviewer comments at the end of this letter. If applicable, we recommend that you deposit your laboratory protocols in protocols.io to enhance the reproducibility of your results. Protocols.io assigns your protocol its own identifier (DOI) so that it can be cited independently in the future. For instructions see: https://journals.plos.org/plosone/s/submission-guidelines#loc-laboratory-protocols. Additionally, PLOS ONE offers an option for publishing peer-reviewed Lab Protocol articles, which describe protocols hosted on protocols.io. Read more information on sharing protocols at https://plos.org/protocols?utm_medium=editorial-email&utm_source=authorletters&utm_campaign=protocols. As the corresponding author, your ORCID iD is verified in the submission system and will appear in the published article. PLOS supports the use of ORCID, and we encourage all coauthors to register for an ORCID iD and use it as well. Please encourage your coauthors to verify their ORCID iD within the submission system before final acceptance, as unverified ORCID iDs will not appear in the published article. Only the individual author can complete the verification step; PLOS staff cannot verify ORCID iDs on behalf of authors. We look forward to receiving your revised manuscript. Kind regards, Zhenhua Li Academic Editor PLOS One Journal Requirements: When submitting your revision, we need you to address these additional requirements. 1. Please ensure that your manuscript meets PLOS ONE's style requirements, including those for file naming. The PLOS ONE style templates can be found at https://journals.plos.org/plosone/s/file?id=wjVg/PLOSOne_formatting_sample_main_body.pdf and https://journals.plos.org/plosone/s/file?id=ba62/PLOSOne_formatting_sample_title_authors_affiliations.pdf 2. We note that the grant information you provided in the ‘Funding Information’ and ‘Financial Disclosure’ sections do not match. When you resubmit, please ensure that you provide the correct grant numbers for the awards you received for your study in the ‘Funding Information’ section. 3. Thank you for stating the following in the Acknowledgments Section of your manuscript: “We thank the precious suggestions by anonymous reviewers and editors, which have greatly helped the improvement of the paper. This research was supported by the National Natural Science Foundation of China (NSFC) (Grant Nos. U22A20600、42507231), Natural Science Foundation Innovation Group Project of Hubei Province (Grant No. 2025AFA015), Talent Research Initiation Fund Program of China Three Gorges University (grant number 2024RCKJ021).” We note that you have provided funding information that is not currently declared in your Funding Statement. However, funding information should not appear in the Acknowledgments section or other areas of your manuscript. We will only publish funding information present in the Funding Statement section of the online submission form. Please remove any funding-related text from the manuscript and let us know how you would like to update your Funding Statement. Currently, your Funding Statement reads as follows: “The author(s) received no specific funding for this work.” Please include your amended statements within your cover letter; we will change the online submission form on your behalf. 4. PLOS requires an ORCID iD for the corresponding author in Editorial Manager on papers submitted after December 6th, 2016. Please ensure that you have an ORCID iD and that it is validated in Editorial Manager. To do this, go to ‘Update my Information’ (in the upper left-hand corner of the main menu), and click on the Fetch/Validate link next to the ORCID field. This will take you to the ORCID site and allow you to create a new iD or authenticate a pre-existing iD in Editorial Manager. 5. Thank you for stating the following in the Competing Interests section: “The authors have declared that no competing interests exist.” We note that one or more of the authors are employed by a commercial company: Power China Hubei Electric Engineering Co., Ltd., Power China Hubei Electric Engineering Co., Ltd., Power China Jiangxi Hydropower Engineering Bureau Co., Ltd. Power China Jiangxi Hydropower Engineering Bureau Co., Ltd. 1. Please provide an amended Funding Statement declaring this commercial affiliation, as well as a statement regarding the Role of Funders in your study. If the funding organization did not play a role in the study design, data collection and analysis, decision to publish, or preparation of the manuscript and only provided financial support in the form of authors' salaries and/or research materials, please review your statements relating to the author contributions, and ensure you have specifically and accurately indicated the role(s) that these authors had in your study. You can update author roles in the Author Contributions section of the online submission form. Please also include the following statement within your amended Funding Statement. “The funder provided support in the form of salaries for authors [insert relevant initials], but did not have any additional role in the study design, data collection and analysis, decision to publish, or preparation of the manuscript. The specific roles of these authors are articulated in the ‘author contributions’ section.” If your commercial affiliation did play a role in your study, please state and explain this role within your updated Funding Statement. 2. Please also provide an updated Competing Interests Statement declaring this commercial affiliation along with any other relevant declarations relating to employment, consultancy, patents, products in development, or marketed products, etc. Within your Competing Interests Statement, please confirm that this commercial affiliation does not alter your adherence to all PLOS ONE policies on sharing data and materials by including the following statement: "This does not alter our adherence to PLOS ONE policies on sharing data and materials.” (as detailed online in our guide for authors http://journals.plos.org/plosone/s/competing-interests) . If this adherence statement is not accurate and there are restrictions on sharing of data and/or materials, please state these. Please note that we cannot proceed with consideration of your article until this information has been declared. Please include both an updated Funding Statement and Competing Interests Statement in your cover letter. We will change the online submission form on your behalf. 6. We note that Figures 1, 3,5, and 6 in your submission contain copyrighted images. All PLOS content is published under the Creative Commons Attribution License (CC BY 4.0), which means that the manuscript, images, and Supporting Information files will be freely available online, and any third party is permitted to access, download, copy, distribute, and use these materials in any way, even commercially, with proper attribution. For more information, see our copyright guidelines: http://journals.plos.org/plosone/s/licenses-and-copyright. We require you to either (1) present written permission from the copyright holder to publish these figures specifically under the CC BY 4.0 license, or (2) remove the figures from your submission: 1. You may seek permission from the original copyright holder of Figure(s) [#] to publish the content specifically under the CC BY 4.0 license. We recommend that you contact the original copyright holder with the Content Permission Form (http://journals.plos.org/plosone/s/file?id=7c09/content-permission-form.pdf) and the following text: “I request permission for the open-access journal PLOS ONE to publish XXX under the Creative Commons Attribution License (CCAL) CC BY 4.0 (http://creativecommons.org/licenses/by/4.0/). Please be aware that this license allows unrestricted use and distribution, even commercially, by third parties. Please reply and provide explicit written permission to publish XXX under a CC BY license and complete the attached form.” Please upload the completed Content Permission Form or other proof of granted permissions as an "Other" file with your submission. In the figure caption of the copyrighted figure, please include the following text: “Reprinted from [ref] under a CC BY license, with permission from [name of publisher], original copyright [original copyright year].” 2. If you are unable to obtain permission from the original copyright holder to publish these figures under the CC BY 4.0 license or if the copyright holder’s requirements are incompatible with the CC BY 4.0 license, please either i) remove the figure or ii) supply a replacement figure that complies with the CC BY 4.0 license. Please check copyright information on all replacement figures and update the figure caption with source information. If applicable, please specify in the figure caption text when a figure is similar but not identical to the original image and is therefore for illustrative purposes only. 7. If the reviewer comments include a recommendation to cite specific previously published works, please review and evaluate these publications to determine whether they are relevant and should be cited. There is no requirement to cite these works unless the editor has indicated otherwise. Additional Editor Comments: You will see from the referees' comments that additional information needs to be provided, and we ask that this be provided, before we consider you manuscript further. [Note: HTML markup is below. Please do not edit.] Reviewers' comments: Reviewer's Responses to Questions Comments to the Author 1. Is the manuscript technically sound, and do the data support the conclusions? Reviewer #1: Partly Reviewer #2: Yes ********** 2. Has the statistical analysis been performed appropriately and rigorously? -->?> Reviewer #1: No Reviewer #2: Yes ********** 3. Have the authors made all data underlying the findings in their manuscript fully available??> The PLOS Data policy Reviewer #1: Yes Reviewer #2: Yes ********** 4. Is the manuscript presented in an intelligible fashion and written in standard English??> Reviewer #1: No Reviewer #2: Yes ********** Reviewer #1: Comments to the Authors, The authors carried out an experimental investigation on the reinforcement performance of unloading-damaged mudstone through microbial grouting. This paper holds a certain degree of research significance. Nevertheless, the innovation and research methods are mediocre. Consequently, I have pinpointed several aspects that necessitate revision prior to its potential final acceptance. specific comments Section numbering is duplicated and erroneous. Please correct the section headings. Section 3 is titled “Study on the reinforcement effect of MICP on unloading-damaged mudstone,” and Section 4 is identically titled. Additionally, Section 4.1 and 4.2 follow, but Section 5 is missing entirely (the manuscript jumps from Section 4.2 to Section 6 “Conclusions”). Please renumber sections sequentially (e.g., 3, 4, 5) and ensure no gaps or duplicates. SEM analysis is critical for supporting the proposed micro-mechanisms. Without scale bars, the reader cannot evaluate the relative size of pores, cracks, or calcium carbonate precipitates. Please add scale bars to all SEM images and include the scale in the figure captions. The definition of the unloading damage degree is not clear. In the text, the unloading damage degree is defined as 70%, 80%, and 90%, but no calculation formula is provided. The statistical analysis of mechanical properties lacks measures of variability (e.g., standard deviation or confidence intervals), which is essential for interpreting the significance of the reported strength increases. The manuscript states that nine parallel specimens were prepared per condition (Section 2.3.1), but only single values are reported. Please include standard deviations or coefficients of variation for peak and residual strengths. This is particularly important given the natural heterogeneity of mudstone and the manual grouting process. The manuscript would benefit from a brief discussion of the practical implications for field applications, especially regarding the injection of volcanic ash-assisted MICP into low-permeability mudstone. Mudstone is known for its low permeability. The laboratory study uses a pre-drilled central grout hole (6 mm diameter) to facilitate solution infiltration. In field conditions, achieving similar distribution of bacteria, cementation solution, and fine volcanic ash particles may be challenging. Please add a paragraph discussing potential field implementation challenges and possible solutions (e.g., grouting pressure, borehole spacing, or pre-conditioning). Table 1 is not described clearly. Please redesign the table. It is suggested to use three groups of comparisons (unreinforced, MICP, MICP + volcanic ash), with each group including residual strength, peak strength and increase. Clearly present the complete data corresponding to all unloading damage degree. Figure 4 is not clearly described. The two vertical axes (σ1 and σ3) overlap. It is recommended to separate them. Figure 5, It is recommended to draw a clear schematic diagram to describe the process of microbial grouting reinforcement, rather than a blurry photograph. Figure 12's mechanism diagram is too simplistic and does not correspond well to the description in Section 4.2. Line 274, Fig. 13 is missing or the reference is incorrect. There are numerous grammatical and spelling errors in the text. Please carefully review it. Reviewer #2: 1.The authors prepared mudstone specimens with unloading degrees of 70%, 80%, and 90%, but failed to provide a clear definition or calculation formula for the "unloading degree." The text only mentions an initial confining pressure of 5 MPa, axial loading up to 80% of the peak strength (held constant), followed by unloading the confining pressure to target values of 2.0, 2.3, and 2.6 MPa. The correspondence between these target confining pressures and the stated unloading degrees (70%–90%) is not explained, nor is it specified whether the unloading degree is calculated based on stress or strain. Recommendation: Clearly define the unloading degree and provide the calculation process mapping each target confining pressure to its corresponding unloading degree. Additionally, supplement the manuscript with a confining pressure unloading path diagram and a detailed description of the stress path. 2.The experimental design includes an unreinforced group, an MICP-only group, and an MICP + volcanic ash group; however, it lacks a "volcanic ash only (without MICP)" grouting group. Since volcanic ash itself possesses physical filling properties and potential pozzolanic activity, its independent effect may already contribute to the reinforcement of the mudstone. Without this control group, it is impossible to quantitatively evaluate the synergistic contributions of MICP and volcanic ash. Recommendation: Add a test group treated solely with volcanic ash grouting (using the same dosage and injection protocol) and subject it to identical mechanical and expansion tests. If supplementary experiments cannot be conducted, this limitation must be explicitly acknowledged in the discussion section, and the authors should avoid attributing all enhancement effects entirely to synergy. 3.The authors claim that nine parallel specimens were prepared for each test group, yet only typical stress-strain curves and mean strength values are presented, without standard deviations, coefficients of variation, or error bars. Given the inherent heterogeneity of natural mudstone and the variability associated with unloading damage, the lack of statistical evaluation severely undermines the reliability of the conclusions. It is recommended to refer to recent research papers in the introduction. Flow mechanism of grouting slurry in rough fracture based on CFD-DEM coupling method. Brittleness evaluation of gas-bearing coal based on statistical damage constitution model and energy evolution mechanism. Recommendation: Include standard deviations or confidence intervals in the text, and illustrate the scatter range of multiple tests using shaded bands or error bars in Figure 8. If the dataset is insufficient, please specify the actual number of samples used for statistical analysis (e.g., the count after excluding outliers). 4.The authors qualitatively describe features such as "rough particle surfaces," "filled pores," and "localized generation of C-S-H gel" via SEM images, but no quantitative image analysis was performed (e.g., pore area fraction, calcium carbonate precipitation coverage rate, or particle contact length). Furthermore, neither EDS spectra nor XRD data were provided to confirm the presence of C-S-H. Recommendation: Supplement the study with quantitative porosity statistics derived from image processing; conduct EDS point scanning or elemental mapping to verify the presence of C-S-H and calcium carbonate; and include XRD phase analysis to clearly identify the mineralogical composition of the mineralization products. 5.After each grouting cycle, the specimens were dried at 40°C for 12 hours. Since the optimal growth temperature for Bacillus cereus typically ranges from 30°C to 37°C, 40°C might inhibit or even kill some microorganisms, leading to reduced mineralization activity in subsequent cycles. The authors have not addressed the impact of this drying step on bacterial survival rates, nor have they verified whether urease activity is maintained at this temperature. Recommendation: Measure the changes in OD600 and urease activity of the bacterial suspension before and after drying, or alternatively, switch to air-drying at room temperature (25°C) with an extended drying duration. If 40°C is strictly necessary, supporting literature or experimental validation must be provided. ********** what does this mean?). If published, this will include your full peer review and any attached files. If you choose “no”, your identity will remain anonymous but your review may still be made public. Do you want your identity to be public for this peer review? For information about this choice, including consent withdrawal, please see our Privacy Policy Reviewer #1: No Reviewer #2: No ********** [NOTE: If reviewer comments were submitted as an attachment file, they will be attached to this email and accessible via the submission site. Please log into your account, locate the manuscript record, and check for the action link "View Attachments". If this link does not appear, there are no attachment files.] To ensure your figures meet our technical requirements, please review our figure guidelines: https://journals.plos.org/plosone/s/figures You may also use PLOS’s free figure tool, NAAS, to help you prepare publication quality figures: https://journals.plos.org/plosone/s/figures#loc-tools-for-figure-preparation. NAAS will assess whether your figures meet our technical requirements by comparing each figure against our figure specifications. Submitted filename: Comments.docx 1 Jul 2026 Response to the Editor’s Comments Thank you very much for your careful review and valuable comments on our manuscript. We have revised the manuscript thoroughly in accordance with your suggestions. All changes have been incorporated into the revised version, and our point-by-point responses are provided below. Reviewer #1 The authors carried out an experimental investigation on the reinforcement performance of unloading-damaged mudstone through microbial grouting. This paper holds a certain degree of research significance. Nevertheless, the innovation and research methods are mediocre. Consequently, I have pinpointed several aspects that necessitate revision prior to its potential final acceptance. Comment 1: Section numbering is duplicated and erroneous. Please correct the section headings. Section 3 is titled “Study on the reinforcement effect of MICP on unloading-damaged mudstone,” and Section 4 is identically titled. Additionally, Section 4.1 and 4.2 follow, but Section 5 is missing entirely (the manuscript jumps from Section 4.2 to Section 6 “Conclusions”). Please renumber sections sequentially (e.g., 3, 4, 5) and ensure no gaps or duplicates Response: Thank you very much for the reviewer’s careful reading and valuable comments. In the revised manuscript, the relevant section titles and numbering have been corrected. Section 3 has been revised as the analysis of the swelling and mechanical properties of reinforced unloading-damaged mudstone, Section 4 has been revised as the analysis of microstructure and reinforcement mechanism, and the conclusions have been renumbered as Section 5, “Conclusions”. In addition, all section and subsection headings throughout the manuscript have been carefully checked to ensure that the numbering is sequential and that there are no missing sections, numbering skips, or duplicated titles. Comment 2: SEM analysis is critical for supporting the proposed micro-mechanisms. Without scale bars, the reader cannot evaluate the relative size of pores, cracks, or calcium carbonate precipitates. Please add scale bars to all SEM images and include the scale in the figure captions. Response: Thank you for the reviewer’s valuable comment. In the original manuscript, the SEM images did not include scale bars, which may have affected readers’ accurate understanding of the microscopic structural features and the spatial distribution scale of the mineralization products. In the revised manuscript, all SEM images have been reorganized, and corresponding scale bars have been added to each SEM image. Comment 3: The definition of the unloading damage degree is not clear. In the text, the unloading damage degree is defined as 70%, 80%, and 90%, but no calculation formula is provided. Response: Thank you for the reviewer’s careful reading and valuable comments. To address the unclear definition of the unloading damage degree in the original manuscript, additional explanations have been provided in Section 2.3 of the revised manuscript. It is clarified that the unloading damage degree in this study is characterized by the magnitude of confining pressure unloading. In essence, it represents a confining pressure unloading degree controlled by the stress path, rather than a value calculated from strain. Meanwhile, the calculation formula for the unloading damage degree has been added to the main text: η=σ30−σ3iσ30−σ3f×100% where σ₃⁰ is the initial confining pressure at the unloading point, σ3i is the target confining pressure after unloading, and σ₃ᶠ is the confining pressure corresponding to specimen failure under the conventional unloading path. According to this equation, the target confining pressures of 2.6, 2.3, and 2.0 MPa used in this study correspond to the designed unloading damage degrees of 70%, 80%, and 90%, respectively. The relevant content has been supplemented in the revised manuscript to improve the clarity and reproducibility of the experimental methodology. Comment 4: The statistical analysis of mechanical properties lacks measures of variability (e.g., standard deviation or confidence intervals), which is essential for interpreting the significance of the reported strength increases. The manuscript states that nine parallel specimens were prepared per condition (Section 2.3.1), but only single values are reported. Please include standard deviations or coefficients of variation for peak and residual strengths. This is particularly important given the natural heterogeneity of mudstone and the manual grouting process. Response: Thank you for the reviewer’s valuable comment. The mechanical properties analysis in Section 3.2 has been supplemented and revised accordingly. The peak strength and residual strength of the parallel specimens in different groups were further statistically analyzed. A new statistical distribution figure has been added to the revised manuscript, and the coefficients of variation for the peak strength and residual strength of each group have been included in Table 1. The results show that the strength data of different groups under various unloading damage degrees exhibit a certain degree of variability, which is related to the natural heterogeneity of mudstone and the spatial variation in mineralization product distribution during artificial grouting. Nevertheless, the overall distribution trend indicates that the peak strength and residual strength of the MICP group and the MICP-volcanic ash group are both higher than those of the unreinforced group, and the improvement is more pronounced in the MICP-volcanic ash group. This indicates that the reinforcement effect remains consistent even when the variability among specimens is considered. The relevant content has been supplemented in the corresponding section of the revised manuscript. Comment 5: The manuscript would benefit from a brief discussion of the practical implications for field applications, especially regarding the injection of volcanic ash-assisted MICP into low-permeability mudstone. Mudstone is known for its low permeability. The laboratory study uses a pre-drilled central grout hole (6 mm diameter) to facilitate solution infiltration. In field conditions, achieving similar distribution of bacteria, cementation solution, and fine volcanic ash particles may be challenging. Please add a paragraph discussing potential field implementation challenges and possible solutions (e.g., grouting pressure, borehole spacing, or pre-conditioning). Response: Thank you for the reviewer’s valuable comment. The practical implications and potential challenges associated with field application have been supplemented in the Discussion section of the revised manuscript. As correctly noted by the reviewer, intact mudstone generally has very low permeability. However, field investigation and laboratory observations indicate that, during subgrade excavation, the rock mass near the excavation surface gradually develops macro- and micro-cracks due to unloading damage. Water infiltration and deterioration along these cracks are among the main causes of subgrade distress. Therefore, the core objective of this study is to repair these macro- and micro-cracks through microbial grouting. The experimental results show that the microbial grout exhibits good diffusibility within these cracks. For field application, the reinforcement effect can be further improved by reasonably arranging grouting boreholes, optimizing borehole spacing, adopting staged low-pressure cyclic grouting, and controlling the particle size of volcanic ash and the grout concentration, so as to enhance the uniform diffusion of bacterial suspension, cementation solution, and volcanic ash particles within the mudstone fracture network. In addition, field permeability tests and small-scale trial grouting should be conducted to optimize the grouting pressure, grouting volume, and number of grouting cycles. Excessively high grouting pressure should be avoided, as it may induce new crack propagation or local hydraulic splitting. Comment 6: Table 1 is not described clearly. Please redesign the table. It is suggested to use three groups of comparisons (unreinforced, MICP, MICP + volcanic ash), with each group including residual strength, peak strength and increase. Clearly present the complete data corresponding to all unloading damage degree. Response: Thank you for the reviewer’s valuable comment. Table 1 has been redesigned in the revised manuscript. In the original version, the data arrangement was not sufficiently intuitive, making it difficult to clearly compare the changes in mechanical properties under different reinforcement methods. In the revised version, Table 1 presents the residual strength, peak strength, and corresponding strength improvement rates of the unreinforced group, MICP group, and MICP-volcanic ash group under unloading damage degrees of 70%, 80%, and 90%, respectively. The improvement rates were calculated using the unreinforced group under the same unloading damage degree as the reference. In addition, the coefficients of variation of the residual strength and peak strength have been added to the table. The relevant content has been revised and supplemented in the corresponding sections of the manuscript. Comment 7: Figure 4 is not clearly described. The two vertical axes (σ1 and σ3) overlap. It is recommended to separate them. Response: Thank you for the reviewer’s careful review and constructive suggestion. In the original manuscript, the unloading stress path shown in Fig. 4 was not sufficiently clear, which could have led to confusion regarding the axial loading process and the confining pressure unloading process. In the revised version, the axial stress σ₁ and confining pressure σ₃ are plotted separately on the left and right vertical axes, respectively. Key parameters, including the initial axial stress, initial confining pressure, target confining pressure after unloading, and the confining pressure corresponding to unloading-induced failure, have also been clearly labeled. In addition, the loading and unloading stages have been re-annotated, and the corresponding loading schematic has been retained to more clearly illustrate the experimental procedure. The relevant modification has been made in Fig. 4 of the revised manuscript. Comment 8: Figure 5, It is recommended to draw a clear schematic diagram to describe the process of microbial grouting reinforcement, rather than a blurry photograph. Response: Thank you for the reviewer’s valuable comment. In the original manuscript, Fig. 5 used a photograph of the experimental setup to illustrate the microbial grouting reinforcement process, which was not sufficiently clear. In the revised manuscript, Fig. 5 has been redesigned, and the original unclear photograph has been replaced with a clear schematic diagram. The revised Fig. 5 schematically presents the main components and operational procedure of the microbial grouting reinforcement process, including the specimen, PVC mold, grouting hole, rubber plugs, injection paths of the bacterial suspension and cementation solution, the connection with the peristaltic pump, and the staged grouting procedure. The corresponding figure and related description have been replaced in the revised manuscript. Comment 9: Figure 12's mechanism diagram is too simplistic and does not correspond well to the description in Section 4.2. Response: Thank you for the reviewer’s valuable comment. In the original manuscript, the schematic diagram in Fig. 12 did not fully illustrate the reinforcement processes of MICP and MICP-volcanic ash treatments. Therefore, Fig. 12 has been redesigned and improved in the revised manuscript. The revised Fig. 12 presents the microbial grouting reinforcement mechanism of damaged mudstone through two pathways: MICP reinforcement and MICP-volcanic ash reinforcement. For the MICP reinforcement process, the figure now includes key processes such as the entry and attachment of bacterial suspension into fractures, Ca²⁺ adsorption and calcium carbonate nucleation, mineralization deposition, and preferential precipitation at fracture constrictions and crack tips. These additions help explain the filling, sealing, and bridging effects of calcium carbonate precipitation in mudstone pores and fractures. For the MICP-volcanic ash reinforcement process, the revised figure further illustrates the bacterial loading, protection, and retention effects of volcanic ash particles, as well as their initial filling effect, nucleation promotion, and possible composite cementation in fractures. These revisions more clearly demonstrate the enhancement effect of volcanic ash on MICP-induced mineralization and structural densification. The relevant modifications have been made in Section 4.2 of the revised manuscript. Comment 10: Line 274, Fig. 13 is missing or the reference is incorrect. Response: Thank you for the reviewer’s careful reading and correction. The figure number cited in this part was indeed inconsistent, which could have caused misunderstanding regarding the correspondence between the text and the figures. This figure reference has been corrected in the revised manuscript. In addition, all figure numbers, figure captions, and in-text figure citations throughout the manuscript have been carefully checked to ensure consistency in the order of first appearance, numbering sequence, and citation positions. The relevant content has been revised accordingly in the manuscript. Comment 11: There are numerous grammatical and spelling errors in the text. Please carefully review it. Response: Thank you for the reviewer’s careful review and valuable comment. The original manuscript contained some grammatical errors, spelling mistakes, and imprecise expressions, which may have affected the readability and academic clarity of the paper. The entire manuscript has therefore been carefully checked and systematically polished. In particular, we revised grammatical and spelling errors, corrected inappropriate punctuation, improved sentence fluency, and unified the use of technical terminology where inconsistencies existed. These revisions have improved the clarity, readability, and overall academic presentation of the manuscript. Reviewer #2: Comment 1: The authors prepared mudstone specimens with unloading degrees of 70%, 80%, and 90%, but failed to provide a clear definition or calculation formula for the "unloading degree." The text only mentions an initial confining pressure of 5 MPa, axial loading up to 80% of the peak strength (held constant), followed by unloading the confining pressure to target values of 2.0, 2.3, and 2.6 MPa. The correspondence between these target confining pressures and the stated unloading degrees (70%–90%) is not explained, nor is it specified whether the unloading degree is calculated based on stress or strain. Recommendation: Clearly define the unloading degree and provide the calculation process mapping each target confining pressure to its corresponding unloading degree. Additionally, supplement the manuscript with a confining pressure unloading path diagram and a detailed description of the stress path. Response: Thank you for the reviewer’s valuable comment. In the original manuscript, the definition of the unloading degree, its calculation basis, and the correspondence between the target confining pressure and the unloading degree were not sufficiently clear. Therefore, the definition and calculation formula of the unloading degree have been supplemented in Section 2.3 of the revised manuscript. In this study, the unloading degree is defined as a stress-based unloading index determined by the magnitude of confining pressure reduction, rather than a strain-based parameter. It is calculated as follows: η=σ30−σ3iσ30−σ3f×100% whereη is the unloading degree; σ30 is the initial confining pressure at the unloading point, which is 5 MPa in this study; σ3i is the target confining pressure after unloading; and σ3f is the confining pressure corresponding to specimen failure under the conventional unloading path. According to the results of preliminary unloading failure tests, σ3f was determined to be 1.6 MPa. Based on this equation, the target confining pressures of 2.6, 2.3, and 2.0 MPa correspond to unloading degrees of 70 Submitted filename: renamed_8a15c.docx 19 Jul 2026 Experimental Study on the Reinforcement Performance of Unloading-Damaged Mudstone by Microbial Grouting PONE-D-26-22352R1 Dear Dr. Zhu, We’re pleased to inform you that your manuscript has been judged scientifically suitable for publication and will be formally accepted for publication once it meets all outstanding technical requirements. Within one week, you’ll receive an e-mail detailing the required amendments. When these have been addressed, you’ll receive a formal acceptance letter and your manuscript will be scheduled for publication. An invoice will be generated when your article is formally accepted. Please note, if your institution has a publishing partnership with PLOS and your article meets the relevant criteria, all or part of your publication costs will be covered. Please make sure your user information is up-to-date by logging into Editorial Manager at Editorial Manager® and clicking the ‘Update My Information' link at the top of the page. For questions related to billing, please contact billing support. If your institution or institutions have a press office, please notify them about your upcoming paper to help maximize its impact. If they’ll be preparing press materials, please inform our press team as soon as possible -- no later than 48 hours after receiving the formal acceptance. Your manuscript will remain under strict press embargo until 2 pm Eastern Time on the date of publication. For more information, please contact onepress@plos.org. Kind regards, Zhenhua Li Academic Editor PLOS One Additional Editor Comments (optional): accept Reviewers' comments: Reviewer's Responses to Questions Comments to the Author Reviewer #1: All comments have been addressed Reviewer #2: All comments have been addressed ********** 2. Is the manuscript technically sound, and do the data support the conclusions??> Reviewer #1: (No Response) Reviewer #2: Yes ********** 3. Has the statistical analysis been performed appropriately and rigorously? -->?> Reviewer #1: (No Response) Reviewer #2: Yes ********** 4. Have the authors made all data underlying the findings in their manuscript fully available??> The PLOS Data policy Reviewer #1: (No Response) Reviewer #2: Yes ********** 5. Is the manuscript presented in an intelligible fashion and written in standard English??> Reviewer #1: (No Response) Reviewer #2: Yes ********** Reviewer #1: (No Response) Reviewer #2: accept. To address the structural deterioration and water-induced swelling of mudstone caused by unloading damage during foundation excavation, MICP and MICP-volcanic ash grouting reinforcement tests were conducted. ********** what does this mean?). If published, this will include your full peer review and any attached files. If you choose “no”, your identity will remain anonymous but your review may still be made public. Do you want your identity to be public for this peer review? For information about this choice, including consent withdrawal, please see our Privacy Policy Reviewer #1: No Reviewer #2: No ********** PONE-D-26-22352R1 PLOS One Dear Dr. Zhu, I'm pleased to inform you that your manuscript has been deemed suitable for publication in PLOS One. Congratulations! Your manuscript is now being handed over to our production team. At this stage, our production department will prepare your paper for publication. This includes ensuring the following: * All references, tables, and figures are properly cited * All relevant supporting information is included in the manuscript submission, * There are no issues that prevent the paper from being properly typeset You will receive further instructions from the production team, including instructions on how to review your proof when it is ready. Please keep in mind that we are working through a large volume of accepted articles, so please give us a few days to review your paper and let you know the next and final steps. Lastly, if your institution or institutions have a press office, please let them know about your upcoming paper now to help maximize its impact. If they'll be preparing press materials, please inform our press team within the next 48 hours. Your manuscript will remain under strict press embargo until 2 pm Eastern Time on the date of publication. For more information, please contact onepress@plos.org. You will receive an invoice from PLOS for your publication fee after your manuscript has reached the completed accept phase. If you receive an email requesting payment before acceptance or for any other service, this may be a phishing scheme. Learn how to identify phishing emails and protect your accounts at https://explore.plos.org/phishing. If we can help with anything else, please email us at customercare@plos.org. Thank you for submitting your work to PLOS ONE and supporting open access. Kind regards, PLOS ONE Editorial Office Staff on behalf of Professor Zhenhua Li Academic Editor PLOS One