Study of stimulation mechanism of hydraulic fracturing induced thermal shock on joint system of geothermal reservoirs Authors: Nan Li, Xiaokai Huang, Rui Wang, Xiaoran Wang, Mingyao Wei, Lei Han, Junjie Li, Lihong Sun Published: 2026 ABSTRACT Hydraulic fracturing has been prevailingly applied to induce thermal shock in geothermal reservoirs for the utilization of geothermal energy. With natural joints commonly distribute in the reservoirs, the stimulation mechanism of thermal shock on joint system is inevitably investigated at fracturing initiation stage to enlarge heat transfer space. In this paper, the interaction of hydraulic fractures (HFs) and joints was simulated by lattice-spring method (LSM). The factors of fluid viscosities, shock times, approaching angles, and joint sets were analyzed to reveal the stimulation effect of thermal shock. The results present that orthogonal approaching angle, moderate shock times, and low fluid viscosity are beneficial to the creation of heat transfer space. The radius of expansion region of the thermal shock is around 1 m, in which the interaction behavior of HFs mainly consists of arrest and penetration. This research aims at revealing the stimulation mechanism of thermal shock on joints and therefore improving the treatment of hydraulic fracturing in geothermal energy development. Introduction Beneath thousands of meters from the earth’s surface, the hot dry rock (HDR) characterized by extremely low permeability and high dryness harbors huge geothermal energy1–3. As a kind of clean energy with vast reserves, the utilization ratio of geothermal energy in the global energy has been increasing for many years4–6. Geothermal energy has the potential to significantly reduce natural gas consumption and greenhouse gas emissions at competitive costs7. The conception of enhanced geothermal system (EGS) was purposed to develop and commercialize the geothermal resources stored in HDR formations and realize the green transformation of energy consumption2,8,9. In the 1970s, physicists at Los Alamos Scientific Laboratory first proposed drilling into HDR reservoirs and then injecting fluids. In the process of fluid flowing through the reservoirs, the geothermal energy can be stored in the high temperature fluid via heat exchange, which then can be transported back to surface through a production well10. The fundamental approach of hydraulic fracturing technique is injecting pressurized water into layers, manifesting a technical advantage in geothermal energy exploitation11–13. Hence, many scholars have studied the propagation of HFs by thermal shock in high-temperature HDR formations14–22. The results indicated that (1) high-temperature, high-injection rate, and high-viscosity injection fluid are crucial for the crack patterns, (2) with the increase of temperature difference, the breakdown pressure decreased and the geometry of HFs became more complicated, and (3) cyclic thermal shock can lead to more cracks and complex HFs networks in HDR formations. Through field observations, there are numerous natural fractures (NFs) in HDR formations, which consists of a massive and intricate joint system that greatly affects the formation of HFs morphology after hydraulic fracturing23. The interaction between HFs and joints was inevitably investigated. By incorporating discrete fracture network into a hydrogeothermal model, Nadimi et al.24 and Xie et al.13 concluded that large-size fractures are conducive to high heat production, and the connectivity of fractures can greatly be affected by injection rate, temperature, and pumping schedule. Based on globally embedded 3D cohesive zone method, Hu et al.25 investigated the fracture geometry by hydrodynamics in shale with weak planes. The finding mainly showed that HFs preferentially extend along weak planes to converted into major fractures, and weak planes with the worst mechanical properties play a dominant role in fracture geometry where coexists different properties of weak planes. By studying the effect of injection schemes on fracture network patterns based on the FORGE (Frontier Observatory for Research in Geothermal Energy) EGS site, Hu et al.26 found that HFs are easily opened under cyclic injection and cracks are tend to extend under stepped injection, meaning that compared with single injection (i.e., cyclic injection and stepped injection), applying alternating injection can create a larger stimulation area. Jordan Pidho et al.27 concluded that the shear stress of deflecting fractures increases along junctions, the total slip is usually reduced in rock with high coefficient friction, and isotropic stress distribution leads to more complex fracture networks. Yuan et al.28 studied the initiation and propagation of hydraulic fractures in HDR under different cyclic injection methods. They analyzed different interaction types of HFs and joints under cycle interval cyclic injection method, and found that the fracturing area of the alternating cyclic injection method is 2.3 ~ 2.7 times that of the single injection scheme. To study the activation effect of thermal treatment on unloading-induced fractures, Liu et al.29 conducted triaxial shear slip experiments on granites samples within saw-cutting surface and suggested that the initial stage of fluid pressurization is critical to the activation of fractures. The result also presented that due to thermal damage, the number of sheared-off asperities increases with the temperature, which in turn leads to an increase in the occurrence of stick–slip events. Induced seismicity is a critical issue in hot dry rock hydraulic fracturing. Previous studies have shown that fluid injection can induce fault reactivation and seismic events30. Experimental results reveal the characteristics of fault slip, energy budget, and precursory stress drop under different injection rates31. The frictional stability of minerals under hydrothermal conditions also plays an important role in injection-induced seismicity32. Through a comprehensive investigation on the above researches, it is concluded that the intrinsic joints of HDR can slip and/or open during thermal shock treatments, therefore altering their structures and areas33,34. During the process, the joint system in HDR formation is stimulated and a considerable space is formed for heat exchange. Due to the influence of thermal shock treatments and joint properties, the different interaction behaviors of HFs and joints appear with different stimulation degrees. Additionally, there is also a lack of relevant research on stimulation mechanism of thermal shock on joint sets. Therefore, it is of great significance to study the stimulation effect on joints in HDR under thermal shock to create a decent heat-transfer space at fracturing initiation stage, which is conducive for realizing efficient geothermal energy utilization. In this paper, under the geological background of Gonghe Basin, we investigate the thermal shock on joint system by LSM. The influence factors, including thermal shock times, approaching angles, fluid viscosities, and joint sets are investigated during hydraulic fracturing. The stress, aperture, stimulation area, and interaction behaviors of joints and HFs are comprehensively analyzed to investigate the stimulation mechanism of thermal shock by hydraulic fracturing. The relationship between stimulation mechanism and treatment parameters are discussed to determine appropriate fracturing methods, which aims at not only revealing the stimulation mechanism of thermal shock on joints, but also providing a reference for adopting optimal treatment to increase the reservoir heat transfer space in geothermal energy development. Geological background The Gonghe Basin in Qinghai Province is a key demonstration site for hot dry rock development in China. Extensive geomechanical studies have been conducted in this area, providing a solid foundation for numerical simulation research35. In order to develop and utilize geothermal energy, Gonghe Basin had been chosen to carry out scientific and technological research on the development of HDR36. As shown in Fig. 1, the basin is in a slope from Yellow River uplift which is shallow in the west and deep in the east to Tanggemu depression37. There are 6 hot springs over 60%, with one at Guide depression reaching the temperature of 93.5 °C. The drilling results indicate that the depth of the granite basement in the Gonghe Basin generally trends from shallow in the east to deep in the west.Fig. 1Schematic diagram of the location of Gonghe basin (after38). Schematic diagram of the location of Gonghe basin (after38). In the eastern part of the basin, the basement is buried at depths of 600 to 1400 m, while in the west, it is buried more than 4000 m deep. The highest temperature of 236 ℃ was revealed at the depth of 3705 m39. The deep in-situ stress measurement shows that the in-situ stress regime of the target HDR reservoir in the Gonghe Basin is normal, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\sigma}_{V}>{\sigma}_{H}>{\sigma}_{h}$$\end{document}, with \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\sigma}_{V}$$\end{document} ranges 81–108 MPa, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\sigma}_{H}$$\end{document} 77–92 MPa, and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\sigma}_{h}$$\end{document} 60–72 MPa. The measurement uncertainty is within ± 5%, which is consistent with previous studies40,41. The rock samples recovered from the drillings show that there exist numerous natural joints in the deep granite due to strong tectonic activities, and the fractured granite is inter-bedded with the complete granite9. Therefore, according to the mechanical properties analysis of Gonghe Basin rock samples under thermal treatment, the physical and mechanical parameters listed in Tables 1 and 2 are determined based on laboratory tests of granite cores from the Gonghe Basin and consistent with published data41–43.Table 1Input physical parameters of HDR reservoir.ParametersGraniteIn-situ stress \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\sigma}_{V}\backslash {\sigma}_{H}\backslash {\sigma}_{h}$$\end{document} (MPa)100\80\65Density (kg/m3)2607Temperature (℃)236Specific Heat (J/Kg/℃)755Thermal Conductivity (W/m/℃)3.07Thermal expansion coefficient (1/℃)4 × 10–6Elastic modulus (GPa)57.5Cohesion (MPa)11.71Friction angle (o)48.9Porosity (%)3.54Poisson’s Ratio0.17Tensile strength (MPa)12.20Shear strength (MPa)20.60Fracture toughness (MPa*m1/2)1.77Permeability (m2)1 × 10–18Biot’s coefficient0.35Compressive strength (MPa)466Pore pressure (MPa)1Table 2Input physical parameters of joint sets.ParametersJoint set 1Joint set 2Tensile strength (MPa)65Cohesion (MPa)0.60.3Friction angle (o)6230Aperture (m)5 × 10–45 × 10–4Permeability (m2)1 × 10–151 × 10–15 Table 1Input physical parameters of HDR reservoir.ParametersGraniteIn-situ stress \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\sigma}_{V}\backslash {\sigma}_{H}\backslash {\sigma}_{h}$$\end{document} (MPa)100\80\65Density (kg/m3)2607Temperature (℃)236Specific Heat (J/Kg/℃)755Thermal Conductivity (W/m/℃)3.07Thermal expansion coefficient (1/℃)4 × 10–6Elastic modulus (GPa)57.5Cohesion (MPa)11.71Friction angle (o)48.9Porosity (%)3.54Poisson’s Ratio0.17Tensile strength (MPa)12.20Shear strength (MPa)20.60Fracture toughness (MPa*m1/2)1.77Permeability (m2)1 × 10–18Biot’s coefficient0.35Compressive strength (MPa)466Pore pressure (MPa)1 Input physical parameters of HDR reservoir. Table 2Input physical parameters of joint sets.ParametersJoint set 1Joint set 2Tensile strength (MPa)65Cohesion (MPa)0.60.3Friction angle (o)6230Aperture (m)5 × 10–45 × 10–4Permeability (m2)1 × 10–151 × 10–15 Input physical parameters of joint sets. Simulation methodology Lattice-spring method With the consideration of the convenience of establishing and running a coupled thermal-hydro-mechanical (THM) model, LSM that treats the target as a group of discrete particles connected by springs, as presented in Fig. 2a, has been adopted to study the interaction behaviors of HFs and joints, which is incorporated into XSite software44,45. By using LSM, Rui and Zhao46 developed a new coupled thermo-mechanical model to solve thermal–mechanical fracturing and large deformation problems and Lv et al.47 found that large intercepting angle, friction angle, and cohesion are conducive to the direct cross behaviors of HFs.Fig. 2Schematic diagram of lattice spring method45: (a) lattice network of rock matrix; (b) matrix flow scheme between fluid nodes. Schematic diagram of lattice spring method45: (a) lattice network of rock matrix; (b) matrix flow scheme between fluid nodes. Mechanical formula For a direct description of highly non-linear behaviors, such as fracture, slip, opening and closure of joints, the motion for translational degrees of freedom of each node can be consisted of the following central difference formulae48:1\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left\{ \begin{array}{ll} \dot{u}_{i}^{(t + \Delta t/2)} = \dot{u}_{i}^{(t - \Delta t/2)} + \sum F_{i}^{(t)} \Delta t/m \hfill \\ u_{i}^{(t + \Delta t)} = u_{i}^{(t)} + \dot{u}_{i}^{(t + \Delta t/2)} \Delta t \hfill \\ \end{array} \right.$$\end{document}where \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\dot{u}}_{i}^{\left(t\right)}$$\end{document} and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${u}_{i}^{\left(t\right)}$$\end{document} are the velocity and displacement of component \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$i\left(i=\mathrm{1,3}\right)$$\end{document} at time t, respectively. \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\sum F}_{i}^{\left(t\right)}$$\end{document} is the sum of all force components i applied on the node of mass m in time step Δ t. The angular velocities \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\omega}_{i}$$\end{document} of component \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$i\left(i=\mathrm{1,3}\right)$$\end{document} at time t are calculated by the equation:2\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\omega_{i}^{(t + \Delta t/2)} = \omega_{i}^{(t - \Delta t/2)} + \Sigma M_{i}^{(t)} \Delta t/I$$\end{document}where \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\sum {M}_{i}}^{\left(t\right)}$$\end{document} is the sum of all moment components i acting on the node of moment of inertia, I. The force status of a node can be reset and obtained from the equation below:3\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left\{ \begin{array}{ll} F_{i}^{N} \leftarrow F_{i}^{N} + \dot{u}^{N} k^{N} \Delta t \hfill \\ F_{i}^{S} \leftarrow F_{i}^{S} + \dot{u}_{i}^{S} k^{S} \Delta t \hfill \\ \end{array} \right.$$\end{document}where \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}^{N}$$\end{document} and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}^{S}$$\end{document} are normal stiffness and shear stiffness, respectively. Fluid flow As the fluid flow in a fracture is corresponded with Plane Poiseuille flow, the flow rate along a pipe from fluid node A to B can be calculated by the equation49:4\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$q = \beta_{f} k_{r} \frac{{a^{3} }}{{12\mu_{f} }}[p^{A} - p^{B} + \rho_{w} g(z^{A} - z^{B} )]$$\end{document}where \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\beta}_{f}$$\end{document} is calibration factor used to match the conductivity of a pipe and a joint; a is fracture aperture; \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\mu}_{f}$$\end{document} is fluid viscosity; \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${P}^{A}$$\end{document} and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${P}^{B}$$\end{document} represent the fluid pressure of node A and B, respectively. \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${z}^{A}$$\end{document} and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${z}^{B}$$\end{document} represent the elevation of node A and B, respectively. \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\rho}_{w}$$\end{document} is fluid density; g is gravitational acceleration. \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{p}$$\end{document}, relative permeability, is the function of saturation s:5\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$k_{p} = s^{2} \left( {3 - 2s} \right)$$\end{document} In a flow time step, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\Delta {t}_{f}$$\end{document}, the pressure increment Δ P is expressed by the equation:6\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\Delta p = \frac{{\sum {q_{i} } }}{{V_{f} }}\frac{aE}{{3R(1 - \upsilon )}}\Delta t_{f}$$\end{document}where \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\sum q}_{i}$$\end{document} is injection rate from the pipes connected to node i; \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${V}_{f}$$\end{document} is the volume of a fluid element; E is the elastic modulus of rock; ν is the Poisson’s ratio; and R is resolution of lattice model. Thermal formulae The heat transfer per unit time and unit area from rock to fluid is evaluated using Newton’s law of cooling50:7\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$q_{cv} = h\left( {T_{r} - T_{f} } \right)$$\end{document}where, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${q}_{cv}$$\end{document} is heat flux, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${T}_{f}$$\end{document} is temperature of the fluid element, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${T}_{r}$$\end{document} is rock temperature of the lattice spring, and h is heat transfer coefficient whose functional form is as follows:8\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$h = \frac{{k_{r} }}{{\beta_{h} \sqrt {\kappa t_{j} } }}$$\end{document}where \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{r}$$\end{document} is rock thermal conductivity, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\beta}_{h}$$\end{document} is heat transfer calibration factor, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${t}_{j}$$\end{document} is injection time, and κ is rock thermal diffusivity calculated by the equation below:9\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\kappa = \frac{{k_{r} }}{{\rho_{r} c_{r} }}$$\end{document}where \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\rho}_{r}$$\end{document} is rock density and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${c}_{r}$$\end{document} is rock specific heat. Therefore, as shown in Fig. 2b, springs can be scanned to compute the temperature change from the unbalanced heat transfer according to the formula below49:10\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\Delta T_{spring}^{(i)} = \frac{{\left( {{}^{left}q_{cv}^{(i)} - {}^{right}q_{cv}^{(i)} } \right)\Delta t}}{{c_{r} m}}$$\end{document}where m is the mass of the node; \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\Delta {T}_{spring}$$\end{document} is temperature change of the spring, which represents the heat transfer from rock to fluid. Heat advection-convection in pipes is solved using a finite volume scheme applied at a fluid element, combined with a temperature upwind technique. The new temperature at the fluid element is calculated from the value at the former timestep using the following incremental relation:11\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$T_{f}^{new} = T_{f}^{old} \left( {1 - \frac{{\sum {Q_{f} \Delta t} }}{{V_{f} }}} \right) - \left( {\sum {T_{f}^{up} Q_{f} } } \right)\frac{\Delta t}{{V_{f} }} + \left[ {\frac{{2h\left( {T_{r} - T_{f} } \right)V_{f} }}{{c_{f} \rho_{f} a_{f} }}} \right]\frac{\Delta t}{{V_{f} }}$$\end{document}where the summation sign applies to pipes that meet at the fluid element, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${Q}_{f}$$\end{document} is the pipe volumetric heat flow rate, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${T}_{f}^{up}$$\end{document} is the temperature at the fluid element located upstream connected by pipes to the fluid element, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\rho}_{f}$$\end{document} is fluid density, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${c}_{f}$$\end{document} is fluid specific heat, and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${a}_{f}$$\end{document} is the aperture of fluid element. Correspondingly, the change of temperature at a spring in the rock lattice is updated as follows:12\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$T_{r}^{new} = T_{r}^{old} - \frac{{\sum {Q^{cv} \Delta t} }}{{c_{r} \rho_{r} V_{r} }}$$\end{document}where \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${V}_{r}$$\end{document} is volume of the lattice spring, and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${Q}^{cv}$$\end{document} is energy rate that follows the equation below:13\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$Q^{cv} { = }\frac{{2h\left( {T_{r} - T_{f} } \right)V_{f} }}{{a_{f} }}$$\end{document} The thermal strains are accounted in the lattice by modifying the normal component of the force vector, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${F}^{n}$$\end{document}, within the spring between the nodes using the following relation:14\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\Delta F^{N} = - k^{N} \alpha L\Delta T$$\end{document}where α is expansion coefficient, L is spring length, and Δ T is temperature change. Fracture propagation criteria In XSite, stress intensity factor, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${K}_{I}$$\end{document}, is adopted as criteria for fracture propagation based on J-integral. For local energy release rate at a fracture tip in the direction of unit vector \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\widehat{r}$$\end{document}, the form of J-integral is expressed as49:15\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$J = \frac{1}{{R_{h} }}\int\limits_{V} {\left[ {\left( {\sigma_{ij} u_{ij} - W\delta_{ki} } \right)q^{{\widehat{r}}} n_{k} - F_{i} u_{ij} q^{{\widehat{r}}} n_{j} } \right]} dV - \frac{1}{{R_{h} }}\int\limits_{S} {T_{j} u_{jk} } q^{{\widehat{r}}} n_{k} dS$$\end{document}where V is a domain of the fracture tip; S is the fracture face; \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${R}_{h}$$\end{document} is half length of the fracture; W is strain energy density; n is unit normal to the domain; F is body force; T is traction; \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\sigma}_{ij}$$\end{document} is Cauchy stress tensor; u is displacement vector; \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${q}^{\widehat{r}}$$\end{document}, sufficiently smooth function to V, can be determined as below:16\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left\{ \begin{gathered} q^{{\widehat{r}}} = 1 - \widehat{r}, \, \left| {\widehat{r}} \right| < 1 \hfill \\ q^{{\widehat{r}}} = 0, \, otherwise \hfill \\ \end{gathered} \right.$$\end{document}17\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\widehat{r} = \sqrt {\widehat{{x_{1} }}^{2} + \widehat{{x_{2} }}^{2} + \widehat{{x_{3} }}^{2} }$$\end{document}18\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\widehat{{x_{i} }} = \frac{{x_{i} - x_{i}^{c} }}{{R_{h} }}$$\end{document}where \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${x}_{i}$$\end{document} and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${x}_{i}^{c}$$\end{document} are the coordinates of the point at the arbitrary and the center of the domain respectively. The stress intensity factor based on J-integral therefore is calculated as:19\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$K_{I} = \sqrt {JE}$$\end{document}where \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${K}_{I}$$\end{document} is stress intensity factor, and E is elastic modulus of the rock. The criterion for the propagation of factures is expressed as below:20\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left\{ \begin{array}{ll} K_{I} < K_{Ic} ,{\text{ non - propagation}} \hfill \\ K_{I} > K_{Ic} ,{\text{ propagation}} \hfill \\ \end{array} \right.$$\end{document}where \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${K}_{Ic}$$\end{document} is rock toughness. Thermal-hydro-mechanical coupling An efficient numerical scheme is implemented that allows for tightly coupled THM simulations45,49. The scheme is based on multi-stepping of the fast advection-convection process (with small explicit timestep) while accumulating the heat convection term that is then transferred to the slow conduction–convection process using a larger timestep. When refers to mechanical logic, according to Eq. (14), thermal strains in the rock induce changes in fracture aperture that, in turn, disturb the local fluid pressures. This then motivates a restoration of a quasi-static state of mechanical equilibrium and quasi-steady fluid flow field. Thus, new fluid velocities are produced that affect the advection-convection process. Numerical model The numerical model is a square plane model with an overall spatial domain larger than the spatial extent of the joints. As shown in Fig. 3, the injection wellbore is arranged at the center of the XY plane. Four natural joints are set symmetrically on both sides of the injection wellbore: the distance from the wellbore center to the first adjacent joint (Joints 2 and 3) is 3 m; the spacing between every two adjacent joints is 1 m. All joints belong to joint set 1 in Table 2 and are perpendicular to the XY plane. Our study focuses on stimulation mechanism of thermal shock on joint systems at the fracturing initiation stage, where the key physical process is cold fluid injection and rapid heat transfer, rather than post-treatment fluid recovery, a single thermal shock is defined as one hydraulic fracturing injection process that only characterizes the heat exchange between injected cold fluid and hot geothermal reservoir. For Sects. “Fluid viscosities”, “Thermal shock times”, “Approaching angles”, all joints are perpendicular to the XY plane. And all joints in this section follow the parameters of Joint set 1 in Table 2. Section “Joint sets” adopts both Joint set 1 and Joint set 2 listed in Table 2.Fig. 3Layout of numerical model. Layout of numerical model. Slickwater fracturing treatments has been adopted because of the successful and widely usage in EGS projects to induce shear slipping of natural joints51. Due to slickwater injected into the Gonghe Basin formation at a high flow rate easily induce strong microseismic events, intermediate flow rate, 3 m3/min, was chosen as injection rate41. The parameters of slickwater for the simulations were presented in Table 3.Table 3Input parameters of fracturing fluid.ParametersSlick waterTemperature (℃)20Density (kg/m3)1010Viscosity (mPa*s)3\5\10Injection rate (m3/min)3Shock times3\5\10Single injection duration (min)5Bulk modulus (GPa)2.2Thermal conductivity (W/m/℃)0.15Coefficient of thermal expansion (1/℃)7 × 10–4Specific heat (J/Kg/℃)4200 Table 3Input parameters of fracturing fluid.ParametersSlick waterTemperature (℃)20Density (kg/m3)1010Viscosity (mPa*s)3\5\10Injection rate (m3/min)3Shock times3\5\10Single injection duration (min)5Bulk modulus (GPa)2.2Thermal conductivity (W/m/℃)0.15Coefficient of thermal expansion (1/℃)7 × 10–4Specific heat (J/Kg/℃)4200 Input parameters of fracturing fluid. Temperature validation Due to the fact that sensors are vulnerable to fluid flow and the heterogeneity of joints, it is hard to process the thermal parameters of joints by experimental trials. Therefore, the equations formulated by Tang et al.52 to calculate temperature under thermal shock were applied to endorse the validation of the simulations. By regarding a joint as a flat plane, the process of thermal shock can be simplified as one-dimensional heat conduction to calculate the temperature on a joint by the formulations below:21\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\frac{{T_{y}^{t} { - }T_{{0}} }}{{T_{f} { - }T_{{0}} }}{ = }erfc\left( {\frac{y}{{2\sqrt {\kappa t} }}} \right) - \exp \left( {\frac{hy}{{k_{r} }} + \frac{{h^{2} \kappa t}}{{k_{r}^{2} }}} \right) \cdot erfc\left( {\frac{y}{{2\sqrt {\kappa t} }} + \frac{{h\sqrt {\kappa t} }}{{k_{r} }}} \right)$$\end{document}where \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${T}_{y}^{t}$$\end{document} is the temperature distribution at time t; \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${T}_{0}$$\end{document} is initial temperature distribution; y is the one-dimensional heat conduction distance from the fracture–joint interaction point to the calculation point on the joint plane, not the global spatial coordinate of the numerical model; \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$erfc\left(\cdot \right)$$\end{document} is Gauss error function:22\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$erfc(r) = 1 - \frac{2}{\sqrt \pi }\int_{0}^{r} {e^{{ - z^{2} }} } dz$$\end{document}23\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$t = \beta_{s} \cdot t_{j}$$\end{document}where \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\beta}_{s}$$\end{document} is scaling factor. Form Fig. 3, for the validation of the simulations, three monitoring points were set on Joint 3, with a spacing of 0.4 m (corresponding to y = 0.4 m, 0.8 m, and 1.2 m, respectively. Therefore, as the scaling simulation time goes by, the comparison of analytical and numerical solution of the monitoring points temperature was shown in Fig. 4. The three groups of curves in Fig. 4 correspond to the temperature evolution data of the three monitoring points one by one.Fig. 4Comparison of temperature evolution on the joint plane. Comparison of temperature evolution on the joint plane. Results analysis Fluid viscosities The increase of fluid viscosity can greatly impact the formation of HFs morphology, which is a crucial parameter for the optimization of fracturing fluid. As fluid viscosity increased from 3 to 5 to 10 mPa*s, the HFs are more likely formed around the injection wellbore, as demonstrated in Fig. 5, which therefore can limit the influence region of thermal shock on joints. According to Fig. 5d, with the viscosity of 3 mPa*s, the area induced by shear stimulation is 21.64 m2, 45% of the whole. Moreover, the shear stimulation area declines with the rise of viscosity, whereas the tension presents a reverse trend.Fig. 5Joints stimulated under different fluid viscosities: (a) 3 mPa*s; (b) 5 mPa*s; (c) 10 mPa*s; (d) stimulation area. Joints stimulated under different fluid viscosities: (a) 3 mPa*s; (b) 5 mPa*s; (c) 10 mPa*s; (d) stimulation area. The stimulation degree of the joints evidently shows a progressive tendency to decline. As presented in Fig. 6, near the injection wellbore, the joint 2 and joint 3 possess the apertures at least 3 times the original. However, the apertures of joint 1 and 4 that far from the injection wellbore were slight changed. Although the joint 1 and 4 were all connected with HF edge, there are different stress patterns on the joints, as shown in Fig. 7. This can be contributed to the difference in the interaction areas. From Fig. 8, the thermal shock area of joint 4 is larger than that of joint 1, in which the stimulation effect is more intensive that a symmetrical stress distribution appeared on the joint 4. Comparatively, with the thermal shock mainly consisted of small-range and low-rate fluid flow, the high stress area of joint 1 is concentrated on the shocked area, resulting a limited stimulation effect. Because the joint 3 is directly crossed by the HF, the high stress area of joint 3 is also small. However, due to the fact that there is no apparent decrease in the fluid flowrate on the joint 3 in the expansion region, the stress applied on the joint 3 is 2 times higher than that on the joint 1, and the aperture is approximately 4 times higher. Due to the interaction behaviors (i.e., penetration and arrest) of the HF on the joint 2, stress concentration occurred between and at the edge of the interaction areas. The reason is that these parts are affected simultaneously by multiple thermal shock because of HF branches.Fig. 6Aperture of joints under different fluid viscosities.Fig. 7Stress of joints under thermal shock with fluid viscosity of 3 mPa*s.Fig. 8Temperature of joints under thermal shock with fluid viscosity of 3 mPa*s. Aperture of joints under different fluid viscosities. Stress of joints under thermal shock with fluid viscosity of 3 mPa*s. Temperature of joints under thermal shock with fluid viscosity of 3 mPa*s. Thermal shock times Thermal shock times refer to the number of independent hydraulic fracturing injection cycles applied in the simulation. Each thermal shock represents one injection–heat exchange process between cold fracturing fluid and hot reservoir rock; no fluid flowback is considered. The thermal shock times adopted in this study are 3, 5, and 10. As shown in Fig. 9, different thermal shock times were applied on the joint set 1. With the increase of shock times, more joints were connected and HFs formed. It can be seen that when HFs interact with joints, part of HFs propagated along the joints, while others penetrated the joints. Figure 9d demonstrates that although shock times can expand the stimulation area of joints, the proportions of shear and tension stimulation vary that shear stimulation occupied 38%, 49%, and 42% for 10, 5, and 3 shock times, respectively. And the shear stimulation areas increased from 13.06 to 26.92 m2, as the shock times turned from 3 to 10. However, the rise of corresponding tension stimulation area presents a more evidently uptrend, which means that shock times should be determined to keep a reasonable ratio of shear and tension stimulation. Figure 10 shows that the aperture of joint 2 is generally larger than that of joint 3 and the aperture of joint 1 is close to that of joint 4. It means that the opening degree of joints declines as the distance from joints and injection borehole increases. Moreover, joint 2 often is the wideset in all cases, which could be contributed to the secondary HFs that arrested by joint 2. Especially, as to the joint 1 and joint 4 under 10 shock times, the apertures even narrower than the original aperture, meaning that thermal shock can compact the space of joints located in the compression region.Fig. 9Joints stimulated under different shock times: (a) 3 shock times; (b) 5 shock times; (c) 10 shock times; (d) stimulation area.Fig. 10Aperture of joints under different thermal shock times. Joints stimulated under different shock times: (a) 3 shock times; (b) 5 shock times; (c) 10 shock times; (d) stimulation area. Aperture of joints under different thermal shock times. Due to shear stimulation is conducive to the shear slide of joints which enhances the self-supporting capacity and then prohibits the closure of joints, the joints under 5 shock times were therefore analyzed, as the temperature and stress distributions shown in Figs. 11 and 12, respectively. Under 5 shock times, the order of HFs interaction degree from high to low can be ranked from the joint 2, joint 3, joint 4, and joint 1. Hence, the temperature on the joint 1 is mostly around 235 ℃. The stress on the joint 1 hits the maximum of 26 MPa near the interaction area from where the stress decreases progressively. The upper part of the joint 2 was penetrated and the lower part was arrested, which makes the middle part undertake the surrounding force. Moreover, the phenomenon of stress concentration appears at the edge of the interaction area. The joint 3 was directly penetrated by the HF, on which the low temperature range is apparently larger than the interaction area, although the stress on the joint 3 is focused on the center of the interaction area that is due to the reason that the joint was mainly affected by fluid flow. As joint 4 was slightly connected with the HF, a symmetric stress distribution was shown on the joint 4, with a small range of corresponding change on the temperature contour in Fig. 11.Fig. 11Temperature of joints under 5 thermal shock times.Fig. 12Stress of joints under 5 thermal shock times. Temperature of joints under 5 thermal shock times. Stress of joints under 5 thermal shock times. Approaching angles Approaching angle (θ) is defined as the angle between the propagation direction of the hydraulic fracture (HF) and the strike direction of the natural joint. It describes the geometric interaction mode between HFs and joints. Three approaching angles are considered: 30°, 60°, and 90° (orthogonal condition). The orientation of joints has greatly impact on the connection direction of HFs and joints. Figure 13 shows the joints stimulated under thermal shock with different approaching angles. It is clear that HFs are more constrained at an approaching angle of 60° compared to the other two scenarios. With small approaching angles, the HFs are more easily propagate along the joints, which is beneficial to the tension stimulation of joints. As the approaching angle increases, the shear stimulation area enlarges from 16.66 to 22.14 m2, with the proportion dominating from 31 to 44%. As shown in Fig. 14, the aperture of joint 1 and 4 are close to the original aperture, the aperture of joint 2 is around 2 mm, and the aperture of joint 3 is around 1.7 mm.Fig. 13Joints stimulated under different approaching angles: (a) 30°; (b) 60°; (c) 90°; (d) stimulation area.Fig. 14Aperture of joints under different approaching angles. Joints stimulated under different approaching angles: (a) 30°; (b) 60°; (c) 90°; (d) stimulation area. Aperture of joints under different approaching angles. As shown in Fig. 15, with the approaching angle of 90°, joint 1 and 4 presents interaction area resembling ellipse shape, while the other two characterize with circle shape. This is due to joint 1 and 4 were slightly connected with the HF, and joint 2 and 3 were penetrated by the HF. The joint 2 was penetrated and arrested by the HF simultaneously, as same individual areas with temperature over 220 ℃ shown on the contour. Therefore, from Fig. 16, due to the inhomogeneity caused by thermal shock, stress concentration occurred around the boundary of arrest and penetration area, as shown on joint 2. The joint 3 was only penetrated by the HF, so the stress is mainly focused on the center. Comparatively, the maximum stress on joint 1 is approximately two-fifths of that on the joint 3, which concentrated on the place corresponding to the temperature contour. Furthermore, as the thermal shock applied on the center of the joint 4, the stress presented a symmetrical distribution on both sides of the center.Fig. 15Temperature of joints under thermal shock with approaching angle of 90°.Fig. 16Stress of joints under thermal shock with approaching angle of 90°. Temperature of joints under thermal shock with approaching angle of 90°. Stress of joints under thermal shock with approaching angle of 90°. Joint sets The dominate directions of the joints in the reservoir of Gonghe Basin can be classified into NWW and NNW53. Therefore, 2 joint sets with an intersection angle of 30° were arranged under scenario 1 (θ = 22.5°) and scenario 2 (θ = 90°), respectively, to analyze the stimulation effect on joints. As shown in Fig. 17, the morphology of HFs connecting with joint sets under the 2 scenarios was demonstrated. It shows that HFs tends to propagate along joint sets, and the connection of joints prolongs flow paths for fracturing fluid. Under a small approaching angle in scenario 1, the HFs are more complicated near the injection wellbore, in comparison with scenario 2. This however leads to a limited stimulation effect that most of fracturing fluid flows in the rock matrix, rather than joints, although the stimulation areas are equally matched. Specifically, as shown in Fig. 18, the proportion of shear stimulation area in scenario 2 is 56.6% in total, which accounts only 47.2% in scenario 1. In addition, the apertures of joint 2 and joint 3 in scenario 2 present the highest respectively in Fig. 18b. Therefore, large approaching angle is conducive to the increase of stimulation effect of thermal shock, especially for multiple joint sets. It is also can be found that the apertures of joint set 2 are smaller than joint set 1, which could be contributed to that joint set 1 was firstly interacted by the HFs.Fig. 17Morphology of joint sets stimulated by hydraulic fractures.Fig. 18Stimulation results of joint sets under different scenarios: (a) stimulation area; (b) joint aperture. Morphology of joint sets stimulated by hydraulic fractures. Stimulation results of joint sets under different scenarios: (a) stimulation area; (b) joint aperture. Figures 19 and 20 show the temperature and stress distribution of joint sets in scenario 1, respectively. And Figs. 21 and 22 depicts the temperatures and stress distribution of joint sets in scenario 2, respectively. With the different behavior of HF interacting with a joint, the stress condition could differ. Form Fig. 19, the lower sides of joint 1 of set 1 was connected with two HF branches. And the middle area presents a high stress, as shown in Fig. 20. This is due to fluid flowing along the two sides that the middle area was mainly washed by the flow from the sides. The same phenomenon occurred in the joint 4 of set 1 of scenario 1. As shown in the joint set 1 in Fig. 21, HFs propagated along the lower part of the joint 2 and upper part of the joint 3, resulting in low temperature on the interaction areas in the 2 joints and high stress areas shown on the pertinent areas in Fig. 22. Especially for the joint 3 of scenario 2, due to the HF branches, a distinct asymmetric stress distribution was shown on the joint.Fig. 19Temperature distribution on joint sets of scenario 1.Fig. 20Stress distribution on joint sets of scenario 1.Fig. 21Temperature distribution on joint sets of scenario 2.Fig. 22Stress distribution on joint sets of scenario 2. Temperature distribution on joint sets of scenario 1. Stress distribution on joint sets of scenario 1. Temperature distribution on joint sets of scenario 2. Stress distribution on joint sets of scenario 2. Discussions Thermal shock treatment As analyzed in Sect. “Results analysis”, the treatment parameters are investigated to optimize the implementation of hydraulic fracturing in HDR reservoirs. During the fracturing initiation stage of thermal shock, the increase of viscosity can hinder the propagation of HFs, leading a more concentrating distribution of HFs around the wellbore and a limited stimulation effect on adjacent joints. Although fracturing pressure increase with fluid viscosity, high-viscosity fracturing fluid would severely affects the stability of injection wellbore. Meanwhile, lower-viscosity fracturing fluid more easily connects micropores and widens cracks54, creating longer fluid paths that beneficial to the diffusion of fluids propagating along joint planes. Therefore, the shear stimulation area induced by the fracturing fluid viscosity of 3 mPa*s is the largest. Thermal shock can reduce the mechanical strength and increase the permeability of reservoirs, therefore creating the most complicated and longest HFs after 10 shock times. With thermal shock continues, more tension stimulation area of joints than shear stimulation area was formed, as the proportion of shear stimulation area reached its maximum after 5 shock times. Additionally, under too many shock times, joints far from injection wellbores could be compacted that narrower than the original state, meaning that optimal shock times should be determined to prevent the closure of joints. When approaching angle is perpendicular to joints, HFs are more likely to penetrate joints, which is helpful to increase the ratio of shear stimulation that contributes to the self-support of joints at fracturing initiation stage. When multiple joint sets exist near an injection wellbore, HFs tend to propagate along joints that served as natural pre-existing paths for fluid to stimulate more fractures. Therefore, once a HF was arrested by a joint, the shape of the joint plays a decisive role in the propagation path. When expanding from the edge of joints into rock matrix, HFs are also likely to divert to the direction plane of maximum principal stress. Since the aperture of joint set 1 is larger than joint set 2 overall, the joint set closer to an injection wellbore can be more stimulated. Thermal shock mechanism As shown in Fig. 23, the limited data points of joint aperture and stress present an obvious non-linear relationship rather than a simple linear correlation. In general, the increase of joint stress can promote the expansion of joint aperture, but this effect is only effective within a reasonable range. For the smooth propagation of hydraulic fractures and the effective expansion of joints, the injection pressure of fracturing fluid should be controlled within an appropriate interval to avoid joint compression and ensure the extension distance of hydraulic fractures, which is more critical for the construction of efficient heat exchange space.Fig. 23Relationship of stress and aperture of joints. Relationship of stress and aperture of joints. The interaction behavior of HFs and joints was illustrated in Fig. 24. Apparently, the joints near an injection wellbore are opened by fluid shock, whereas the joints far from the wellbore could be impacted by the force of rock deformation due to the shock. Therefore, the fluence region of thermal shock the region can be divided into expansion region and compression region. As the joint 4 was compressed after 10 shock times and the aperture of joint 2 and 3 was increased in all the cases, the radius of expansion region and influence region of the thermal shock treatment is around 1 and 2 m, respectively. Between the two regions is compression region. Decreasing fluid viscosity and shock times can shrink the influence range of thermal shock, which is therefore beneficial for HFs to expand the joints adjacent and connect with joints distant. When HFs connect with joints, the behaviors of arrest and/or penetration occurs. The degree of the interaction behavior can result in different stress and temperature distribution on joints. When a HF slightly interact with a joint, the stress distribution could be symmetrical or gradient. No matter penetration or arrest, the high stress area of the joints could appear near the interaction area, which is due to the fluid flow causing inhomogeneity and stress concentration. Furthermore, when a joint connected with HF branches, the middle area between the branches usually presents a high temperature, with an asymmetrical stress distribution that enhances the inhomogeneity of joint aperture. It is also evident that the stress and aperture of joints decrease as the distance between the joints and the wellbore increases.Fig. 24Interaction behaviors of thermal shock induced hydraulic fractures and joints. Interaction behaviors of thermal shock induced hydraulic fractures and joints. Conclusions This paper provides reference for the development of artificial heat storage near injection wells at fracturing initiation stage. Under the consideration of fluid viscosity, thermal shock time, approaching angle and joint sets, we investigated the stimulation effect and mechanism of thermal shock on joint system by LSM, which is meaningful for adopting optimal treatment to increase heat transfer space in HDR reservoirs. The main conclusions are as follows:Based on the above engineering background, low-viscosity fracturing fluid (≈ 3 mPa·s) is suggested to maximize shear stimulation of joint systems. A cycle number of 4–6 thermal shocks is optimal to balance stimulation intensity and avoid joint compaction. Well trajectory and perforation design should aim to achieve nearly orthogonal approaching angles (≈ 90°) between hydraulic fractures and natural joints. Meanwhile, a moderate injection rate (≈ 3 m3/min) is recommended to ensure wellbore stability and sufficient thermal impact during fracturing operations. Thermal shock around the injection wellbore forms a distinct expansion region and a compression region. The expansion region (approximately 1 m in radius) is characterized by joint opening driven by fluid injection, while the outer compression region (total influence radius ≈ 2 m) is dominated by rock deformation that tends to close distant joints.During fracturing initiation stage of thermal shock, fluid viscosity has greatly impact on the morphology of HFs, which should be designed to adjust the expansion region for near-wellbore joints expansion and local stimulation effect. Thermal shock time characterizes with the continuous stimulation effect on joints. The times of thermal shock should be determined because there exist optimal shock times that effectively enhance the self-supporting capacity and prohibit the closure of joints. With an orthogonal approaching angle, HFs are more easily to penetrate joints, which is conducive to the shear stimulation of thermal shock. The injection pressure of fracturing fluid should be optimized to keep joints from being compressive, which is more meaningful to HFs expansion and creation of heat exchange space.Under the scenario of multiple joint sets, HFs are more likely to expand along the joint planes from sets to sets. Especially, the joint set near an injection wellbore is more stimulated than others distant. The stress and aperture of joints decrease as the distance between the joints and the wellbore increases.When HFs interact with joints, the interaction behaviors of HFs and joints mainly consists of arrest and penetration. The interaction degree of those behaviors leads to symmetrical, asymmetrical, and gradient stress distributions on joints, resulting in different stimulation degree of thermal shock. Due to the interaction by HF branches, fluid flow could induce stress concentration at the boundary of area between the branches, therefore increasing the roughness and heterogeneity of joints. Based on the above engineering background, low-viscosity fracturing fluid (≈ 3 mPa·s) is suggested to maximize shear stimulation of joint systems. A cycle number of 4–6 thermal shocks is optimal to balance stimulation intensity and avoid joint compaction. Well trajectory and perforation design should aim to achieve nearly orthogonal approaching angles (≈ 90°) between hydraulic fractures and natural joints. Meanwhile, a moderate injection rate (≈ 3 m3/min) is recommended to ensure wellbore stability and sufficient thermal impact during fracturing operations. Thermal shock around the injection wellbore forms a distinct expansion region and a compression region. The expansion region (approximately 1 m in radius) is characterized by joint opening driven by fluid injection, while the outer compression region (total influence radius ≈ 2 m) is dominated by rock deformation that tends to close distant joints. Based on the above engineering background, low-viscosity fracturing fluid (≈ 3 mPa·s) is suggested to maximize shear stimulation of joint systems. A cycle number of 4–6 thermal shocks is optimal to balance stimulation intensity and avoid joint compaction. Well trajectory and perforation design should aim to achieve nearly orthogonal approaching angles (≈ 90°) between hydraulic fractures and natural joints. Meanwhile, a moderate injection rate (≈ 3 m3/min) is recommended to ensure wellbore stability and sufficient thermal impact during fracturing operations. Thermal shock around the injection wellbore forms a distinct expansion region and a compression region. The expansion region (approximately 1 m in radius) is characterized by joint opening driven by fluid injection, while the outer compression region (total influence radius ≈ 2 m) is dominated by rock deformation that tends to close distant joints. During fracturing initiation stage of thermal shock, fluid viscosity has greatly impact on the morphology of HFs, which should be designed to adjust the expansion region for near-wellbore joints expansion and local stimulation effect. Thermal shock time characterizes with the continuous stimulation effect on joints. The times of thermal shock should be determined because there exist optimal shock times that effectively enhance the self-supporting capacity and prohibit the closure of joints. With an orthogonal approaching angle, HFs are more easily to penetrate joints, which is conducive to the shear stimulation of thermal shock. The injection pressure of fracturing fluid should be optimized to keep joints from being compressive, which is more meaningful to HFs expansion and creation of heat exchange space. During fracturing initiation stage of thermal shock, fluid viscosity has greatly impact on the morphology of HFs, which should be designed to adjust the expansion region for near-wellbore joints expansion and local stimulation effect. Thermal shock time characterizes with the continuous stimulation effect on joints. The times of thermal shock should be determined because there exist optimal shock times that effectively enhance the self-supporting capacity and prohibit the closure of joints. With an orthogonal approaching angle, HFs are more easily to penetrate joints, which is conducive to the shear stimulation of thermal shock. The injection pressure of fracturing fluid should be optimized to keep joints from being compressive, which is more meaningful to HFs expansion and creation of heat exchange space. Under the scenario of multiple joint sets, HFs are more likely to expand along the joint planes from sets to sets. Especially, the joint set near an injection wellbore is more stimulated than others distant. The stress and aperture of joints decrease as the distance between the joints and the wellbore increases. Under the scenario of multiple joint sets, HFs are more likely to expand along the joint planes from sets to sets. Especially, the joint set near an injection wellbore is more stimulated than others distant. The stress and aperture of joints decrease as the distance between the joints and the wellbore increases. When HFs interact with joints, the interaction behaviors of HFs and joints mainly consists of arrest and penetration. The interaction degree of those behaviors leads to symmetrical, asymmetrical, and gradient stress distributions on joints, resulting in different stimulation degree of thermal shock. Due to the interaction by HF branches, fluid flow could induce stress concentration at the boundary of area between the branches, therefore increasing the roughness and heterogeneity of joints. When HFs interact with joints, the interaction behaviors of HFs and joints mainly consists of arrest and penetration. The interaction degree of those behaviors leads to symmetrical, asymmetrical, and gradient stress distributions on joints, resulting in different stimulation degree of thermal shock. Due to the interaction by HF branches, fluid flow could induce stress concentration at the boundary of area between the branches, therefore increasing the roughness and heterogeneity of joints.