Engineering turbulence resilience in Bessel-Vortex beams through partial coherence and topological charge pairing Authors: Jalil Jafari Dashkasan, Rasoul Aalipour, Mohammad Yeganeh Published: 2026 ABSTRACT AbstractEngineering optical resilience against atmospheric turbulence is essential for robust free-space photonic technologies. Here, we demonstrate that dual partially coherent Bessel-Vortex beams—with engineered topological charge pairing—exhibit unprecedented control over turbulence-induced scintillation beyond what is achievable with single beams or partial coherence alone. Using a spatial light modulator, we generate single and dual partially coherent Bessel-Vortex beams and propagate them through a laboratory turbulence chamber calibrated to Kolmogorov statistics () over a 0.15 m path, corresponding to a 1 km atmospheric propagation with equivalent turbulence strength . A key technical innovation of this work is the simultaneous encoding of both the Bessel-Vortex phase profile and the Kolmogorov-distributed random phase onto a single hologram displayed on the SLM—enabling real-time generation of partially coherent structured beams without additional optical components. We find that dual-beam configurations with co-signed topological charges show monotonically increasing resilience with charge difference, whereas counter-signed pairs display a pronounced non-monotonic response with minimal resistance at Δm = 8. Most strikingly, beams with equal-magnitude opposite charges (|m₁| = |m₂|) exhibit monotonic degradation in resilience up to order 14—a behavior absent in single-vortex systems. These results establish dual topological charge pairing as a previously unexplored design parameter for turbulence-resilient optical systems, with direct implications for free-space optical communication, quantum information transfer, and high-precision optical manipulation.Keywords: Atmospheric turbulence, Free-space optical communication, Partial coherence, Dual Bessel-Vortex beams, Scintillation indexSubject terms: Optics and photonics, Physics Introduction In free-space optical communications, astronomical imaging, optical lidar, and laser beam propagation through the atmosphere, the effects of atmospheric turbulence on optical beam propagation are of considerable concern1,2. These effects distort the beam profile and degrade the focusing quality of the beam. Furthermore, turbulence can disrupt the information transmitted by the beam. Atmospheric turbulence can be defined as random spatial and temporal fluctuations in the refractive index, caused by temperature variations. Such conditions cause the optical beam to undergo distortion, intensity fluctuations (scintillation), and lateral displacement, known as beam wander, during atmospheric propagation3–8. To correct wavefront distortions, adaptive optics is commonly employed9,10. This approach improves the performance of optical systems or mitigates wavefront aberrations. However, it requires highly complex and precise optical and electronic control systems, making it a costly solution. Various models have been developed to characterize the effects of atmospheric turbulence, including the Tatarski, von Kármán, and Greenwood models11,12. Among these, Kolmogorov’s cascade theory stands out as one of the most significant and widely applied frameworks in turbulence research. Among the various metrics used to quantify atmospheric turbulence strength, the Fried parameter stands as a pivotal and widely used indicator. The Fried parameter (denoted ), also referred to as the atmospheric coherence length, is a critical metric in optical propagation through turbulent media. It is defined as the diameter of a circular patch on a wavefront over which the root‑mean‑square (RMS) phase deviation induced by atmospheric turbulence does not exceed one radian. Within this coherence cell, the wavefront can be considered approximately planar, and phase variations remain predictable13,14. Another important parameter for measuring the turbulence intensity is the scintillation index. It quantifies the intensity fluctuations of light caused by atmospheric turbulence, reflecting the temporal and spatial variations in signal strength due to refractive index irregularities in the atmosphere15. The scintillation index is typically used to assess the effects of turbulence on non‑diffracting beams, such as Laguerre–Gaussian or Bessel-Vortex beams. With increasing atmospheric turbulence, the scintillation index—and consequently the intensity fluctuations—become larger, leading to a reduction in the signal-to-noise ratio (SNR). One approach to mitigating the effects of atmospheric turbulence on beam propagation is to use beams that are less susceptible to such turbulence. This method is more cost-effective and less complex than adaptive optics systems. Studies over recent decades have shown that partially coherent Gaussian beams are less sensitive to atmospheric turbulence than fully coherent Gaussian beams16–19. The role of spatial coherence in shaping optical field properties has also been demonstrated in diffractive optics. For instance, Farahiyan and Aalipour recently showed that tailoring spatial coherence can significantly enhance the depth of focus in sinusoidal linear Fresnel zone plates—a finding that underscores the broader utility of coherence engineering beyond turbulence mitigation20. Moreover, vortex beams, such as Bessel-Vortex beams, exhibit reduced susceptibility to turbulence compared to Gaussian beams during propagation through turbulent atmospheres21–28. Partially coherent light has been extensively studied as an effective means for mitigating turbulence-induced degradation owing to its intrinsic statistical averaging properties, with comprehensive theoretical foundations and applications summarized in recent reviews29. Building on this framework, partially coherent structured beams have been successfully employed in diverse areas such as robust optical sensing, turbulence-resistant image transmission, multidimensional optical encryption, and emerging optical computing architectures, where reduced sensitivity to phase fluctuations and scintillation plays a crucial role30–35. Moreover, recent studies have addressed turbulence-induced scintillation and its supprcoherence$0ession through coherence tailoring and phase-structure engineering of structured beams36,37. While these works primarily focus on optimizing spatial coherence or phase modulation independently, the present study introduces a distinct and complementary strategy by jointly engineering partial coherence and topological charge pairing in Dual Bessel–Vortex Beams (DBVB). This approach reveals how the relative sign and combination of topological charges provide an additional degree of freedom for controlling turbulence resilience, extending beyond what is achievable through partial coherence or structured phase design alone. This resilience was recently quantified for zero-order Bessel–Gaussian beams under dynamic Kolmogorov turbulence simulated via a rotating pseudo-random phase plate (PRPP); however, that study was limited to single-component beams and did not explore the interference-enhanced robustness achievable through dual-topological configurations—a strategy uniquely demonstrated in the present work15. Recent studies have demonstrated that dual vortex beams, generated by the coaxial superposition of two vortex beams with distinct topological charges, possess unique properties and offer significant potential for advanced research applications, such as propagation in turbulent atmospheres38–40. Recent studies have demonstrated that, beyond tailoring spatial coherence alone, cross-phase engineering provides a powerful approach for enhancing the robustness of partially coherent structured beams against atmospheric turbulence. For instance, robust measurement of orbital angular momentum (OAM) in partially coherent vortex beams has been achieved even under strong amplitude and phase perturbations, highlighting the role of statistical averaging in suppressing turbulence-induced distortions41. Furthermore, cross-phase modulation has been employed to generate partially coherent persistent hollow beams, enabling the preservation of beam structure and energy distribution in turbulent environments42. In addition, single-shot, intensity-only techniques have been developed for measuring high-order OAM in partially coherent vortex beams, significantly reducing sensitivity to phase distortions and scintillation effects43. These works collectively demonstrate that phase-structure engineering and coherence control can jointly improve turbulence resilience. In contrast to these approaches, the present work explores a complementary and previously less-studied mechanism by investigating how topological charge pairing in Dual Partially Coherent Bessel-Vortex Beams modifies turbulence robustness beyond what is achievable through partial coherence or cross-phase engineering alone. Recent studies by Lekshmi and Narayanamurthy have extended the understanding of turbulence resilience to partially coherent vortex beams, demonstrating that higher topological charge and reduced spatial coherence can suppress scintillation under dynamic Kolmogorov turbulence simulated via a rotating pseudo-random phase plate (PRPP)44. While their work established the advantage of single-component vortex beams in turbulence mitigation, it does not explore the interference-driven robustness of dual-beam configurations. In contrast, our approach leverages coaxially superimposed dual partially coherent Bessel-Vortex beams with independently tailored topological charges—a strategy that unlocks non-monotonic resilience profiles unattainable with single beams. Furthermore, our optical turbulence generator (OTG), based on convective mixing of hot and cold air, emulates a broadband Kolmogorov spectrum (up to 10 kHz), offering a more realistic representation of atmospheric dynamics compared to the spatially static phase statistics of PRPP-based simulators. These advances, alongside recent demonstrations of robustness in complex structured beams such as radial carpet modes45,46, highlight a growing consensus that turbulence resilience is governed not only by coherence and topology, but by the fine spatial design of the optical field—a principle directly exploited in our dual-topological engineering framework. This paper experimentally investigates the effects of atmospheric turbulence on partially coherent Bessel-Vortex (PCBV) beams and dual Bessel-Vortex beams. To generate partially coherent beams, the Kolmogorov energy‑cascade theory was employed. In the experimental setup, PCBV beams are produced by illuminating a Gaussian laser beam onto a digital hologram. To simulate atmospheric turbulence in the laboratory, an optical turbulence generator (OTG) was used, operating on the principle of mixing hot and cold air and adhering to Kolmogorov’s energy-cascade theory38. Theoretical analysis The electric field of a vortex beam with an arbitrary initial phase is given by Eq. (1)19: By modulating the complex amplitude, A(r), various types of vortex beams, such as Laguerre-Gaussian and Bessel-Vortex beams, can be generated. Bessel-Vortex beams are non-diffracting beams with self-healing properties; if an obstacle partially obstructs the beam, it reconstructs itself after propagation. These beams have a cylindrically symmetric intensity profile, featuring a central peak surrounded by concentric rings. The wave function associated with Bessel-Vortex beams is derived by solving the Helmholtz equation in cylindrical coordinates. The complex amplitude for a Bessel-Vortex-Gaussian beam at the source plane (z = 0) can be obtained from Eq. (2)15,46: In the above equation, r denotes the radial distance from the z-axis, θ represents the azimuthal angle, A is the complex amplitude, is the spherical Bessel-Vortex function of order l, ​is the wave vector component corresponding to the radial direction, and is the beam waist of the Gaussian beam. A dual Bessel-Vortex beam can be defined as Eq. (3): Where A and B are the complex amplitudes, and denote the sizes of the inner and outer vortex beams, and l1 and l2 indicate the inner and outer topological charges of the optical vortex. In partially coherent vortex beams, the initial phase in Eq. (1) is not fixed and is completely random. To describe partial coherence, the cross-spectral density is commonly utilized. The cross-spectral density, expressed in terms of the correlation function between two points in the source plane, is given by Eq. (4)47–49: If the complex amplitude A(r) of a Bessel-Vortex beam is expressed as , where is the radial spatial frequency and ​ is the Bessel function of order l, then the Bessel-Vortex-Gaussian correlation function in the Shell model is given by Eq. (5)47: In the above relation, represents the initial coherence length. When →0, the beam becomes incoherent, whereas when →∞, it is fully coherent. The Cross-Spectral Density (CSD) in the double Bessel-Vortex beam can be derived from Eq. (6) as follows: Equation (6) consists of two terms: the cross-correlation and the self-correlation components. Assuming that the amplitudes and are real, we have: Assuming that the two fields exhibit only spatial correlation (), the Cross-Spectral Density of the partially coherent double Bessel–Vortex beam in the Shell model can be derived from Eq. (11). For example, in a specific case where , we have and . In this situation, the interference term becomes simpler, and Eq. (11) reduces to Eq. (12). In partially coherent media, the CSD is determined by averaging over phase or intensity fluctuations, where the cross-terms () are modulated by a spatially normalized coherence function, The calculated quantity represents the Cross-Spectral Density between two partially coherent fields, each carrying a specific Orbital Angular Momentum (OAM) mode, and . The resulting intensity distribution is governed by three main physical factors: Spatial Coherence (): The exponential pre-factor dictates the spatial extent over which the two points, and , remain correlated. A smaller signifies weaker coherence and a more localized correlation, which generally smears out high-contrast interference features. Spatial Coherence (): The exponential pre-factor dictates the spatial extent over which the two points, and , remain correlated. A smaller signifies weaker coherence and a more localized correlation, which generally smears out high-contrast interference features. Mode Magnitude (): The magnitude of the topological charge () determines the azimuthal phase structure, , which concentrates the intensity in an annular region away from the center (doughnut-like intensity profile). Mode Magnitude (): The magnitude of the topological charge () determines the azimuthal phase structure, , which concentrates the intensity in an annular region away from the center (doughnut-like intensity profile). Topological Charge Difference (): The cross-term, which includes the factor, is the source of the cross-shaped interference pattern. This pattern arises specifically when there is a non-zero difference in the azimuthal phase dependence between the two components. The most distinct cross pattern is achieved when , where the difference term maximizes the angular modulation. When , this modulation disappears, and the interference simplifies to a non-angular, radial-only correlation. Topological Charge Difference (): The cross-term, which includes the factor, is the source of the cross-shaped interference pattern. This pattern arises specifically when there is a non-zero difference in the azimuthal phase dependence between the two components. The most distinct cross pattern is achieved when , where the difference term maximizes the angular modulation. When , this modulation disappears, and the interference simplifies to a non-angular, radial-only correlation. The spatial coherence and topological charges can be engineered such that the resulting partially coherent double Bessel-Vortex beam exhibits enhanced robustness against atmospheric turbulence effects. The Physical Analysis of Eq. (5) across various states topological charges are summarized in Table 1. Table 1The Physical Analysis of Eq. (5) across various states topological charges.CasePhysical conditionInterference pattern implication Identical topological charges (full phase overlap)The term simplifies to 1. The interference reduces to the self-correlation of the beam, leading to a pattern independent of the angular separation Opposite topological charges (maximum phase difference)The term becomes . This condition maximizes the angular-dependent interference, typically resulting in the characteristic four-fold cross-shaped pattern Different topological chargesThe interference results in an angular distribution where the number of observable lobes or spokes in the pattern is proportional to The Physical Analysis of Eq. (5) across various states topological charges. In this study, partially coherent Bessel-Vortex and dual Bessel-Vortex beams are generated in the laboratory using digital holography, with holograms created by a spatial light modulator (SLM). To generate partially coherent Bessel beams, fork gratings were designed in MATLAB and implemented simultaneously on a spatial light modulator (SLM), together with a time-varying random phase β consistent with Kolmogorov’s energy‑cascade theory, and illuminated by a Gaussian laser beam. The method employed to generate partially coherent Bessel beams is a novel technique, used here for the first time. The applied random phase adheres to Kolmogorov’s energy‑cascade theory. According to this theory, phase power spectrum is given by Eq. (14)15: where is the spatial frequency, ​ is the Fried parameter, is the outer scale of turbulence, and is the inner scale of turbulence. By adjusting the Fried parameter, the spatial coherence of the generated beams can be controlled. In the Kolmogorov turbulence model, ​ relates to the refractive index structure parameter along the propagation path by13,50,51: Where λ is the wavelength. Additionally, the spectral power density as a function of turbulence intensity is given by Eq. (16)50: The phase structure function in the Kolmogorov’s energy‑cascade theory is defined by Eq. (17): Where . Thus, the phase correlation between the two points is derived using Eq. (18): By substituting the Kolmogorov model for the Shell model in by Eq. (5), Bessel-Vortex correlation function in the Kolmogorov model () is derived from Eq. (19): The Cross-Spectral Density of the partially coherent double Bessel–Vortex beam in the Kolmogorov model can be derived from Eq. (20): The experimental setup and the method used to generate partially coherent Bessel beams are described in detail further in the following section. Experimental and simulation works To simulate real-world turbulent atmospheric conditions in a laboratory environment, an OTG (featuring dimensions of 600 mm × 400 mm × 200 mm) was designed and constructed13. This OTG operates by combining hot and cold air flows, enabling the generation of controlled turbulence profiles for experimental studies. The active region of the OTG is 100 mm long, while the total beam propagation length inside the OTG is 400 mm. The laboratory-built OTG exhibits a statistical spectrum that aligns with the Kolmogorov turbulence model, characterized by the atmospheric coherence length. The turbulence intensity can be controlled by adjusting parameters such as the temperature difference and fan speed. The cutoff frequency range of the OTG has been empirically determined to be approximately 10 kHz. The OTG was characterized using an experimental arrangement similar to the setup illustrated in Fig. 1. A He–Ne laser beam (wavelength 632 nm, power 2 mW) was first expanded by a lens L1 (f = 25 mm) and then collimated by a lens L2 (f = 100 mm) before being directed toward the OTG. The expanded beam (diameter 5 mm) then passed through the turbulence chamber integrated into the setup. A CCD camera (acA1300-60gmNIR, Basler) was positioned at the focal plane of lens L3 (f = 100 mm) to capture the intensity of the distorted field. To avoid saturation of the CCD sensor, a neutral density (ND) filter was used. The distance from L2 to OTG is 20 cm, and the distance from OTG to L3 is 15 cm. Image data were recorded continuously for 15 s at a frame rate of 160 fps for each applied temperature difference. Schematic of the experimental setup for characterized of the fabricated OTG. The Fried parameter and atmospheric turbulence strength were obtained using the angle of arrival (AOA) method5, based on data recorded at various OTG temperature settings (see Fig. 2). For the maximum temperature difference (35 °C) in the OTG, the turbulence strength and Fried parameter were determined to be 7.6 × 10–11 m-2/3and 3.9 mm, respectively. In this work, we distinguish between two distinct coherence parameters: (i) the atmospheric Fried parameter , which characterizes the strength of turbulence generated by the optical turbulence generator (OTG), and (ii) the source coherence parameter , which describes the spatial coherence of the beam as engineered by the random phase screen applied to the spatial light modulator (SLM). The parameter was varied by adjusting the temperature difference in the OTG (Fig. 2), whereas was controlled independently by tailoring the statistics of the random phase screen displayed on the SLM. Importantly, does not represent actual atmospheric turbulence; rather, it provides an equivalent description of the beam’s initial coherence state. A large (e.g., ) corresponds to a fully coherent beam (no random phase applied to the SLM), whereas small values (e.g., 1 mm) represent highly partially coherent beams. Fried parameter (a) and refractive index structure constant (b) for different temperature differences of the OTG, measured using a 5 mm diameter Gaussian beam. The effective atmospheric turbulence strength experienced by the beam is characterized by the path-integrated parameter , where is the propagation length through the OTG. To facilitate comparison with a 1 km atmospheric path while preserving the same total turbulence effect (i.e., the same value of ), we define an equivalent structure constant as: We emphasize that this linear scaling is a simplified equivalence relation used solely for qualitative comparison of turbulence strength between laboratory and atmospheric propagation scenarios. It preserves the path-integrated turbulence parameter , which governs phase structure function behavior in the weak-turbulence regime. This approach is consistent with the methodology employed in Refs.52 for laboratory-to-atmosphere turbulence scaling. The effective impact of atmospheric turbulence on an optical beam is proportional to both the parameter and the propagation length L. The total turbulence effect can be expressed as ×L, where L is the path length over which the optical beam propagates. This linear scaling, , is specifically adopted to accurately reproduce the Rytov variance () and phase structure function (PSF) behavior observed in controlled laboratory settings, as supported by previous literature53. Therefore, the maximum value of (7.6 × 10−11 m− 2/3) generated in the OTG corresponds to an equivalent atmospheric of 1.14 × 10−14 m− 2/3 over a propagation distance of 1 km. To generate partially coherent Bessel-Vortex beams, a spatial light modulator (SLM) was placed immediately after lens L2 and before the OTG in the configuration shown in Fig. 1. The SLM was extracted from a used EPSON EX7210 video projector and has a resolution of 1280 × 800 pixels with a pixel pitch of 4.5 μm. Figure 3 illustrates the experimental setup designed for generating partially coherent Bessel-Vortex beams and investigating the effects of atmospheric turbulence on their propagation. Experimental setup for generating partially coherent Bessel-Vortex beams and investigating the effects of atmospheric turbulence on their propagation. To generate Bessel-Vortex and dual Bessel-Vortex beams, digital holograms for each beam type were simulated using MATLAB and displayed on the SLM. Illuminating the LCD-based SLM with a He–Ne laser beam (diameter 5 mm) produces the desired beam profile in the first diffraction order. Figure 4 shows a sample hologram, the corresponding beam image, and simulations of dual Bessel-Vortex beams at various diffraction orders. To generate partially coherent Bessel-Vortex beams, a temporally varying random phase consistent with Kolmogorov’s energy-cascade theory was added to the digital hologram of the desired Bessel-Vortex beam and displayed as a movie on the SLM. The degree of spatial partial coherence is characterized by the source coherence length σg (in mm), which determines the correlation scale of the random phase fluctuations applied to the beam. Illuminating the SLM with an expanded Gaussian laser beam then yields the intended beam profile. Hologram, corresponding beam image, and simulations of dual Bessel-Vortex beams at various diffraction orders. Since there was not enough space in Fig. 4 to indicate the scale bar and color bar for each individual image, these calibration parameters are shown in Fig. 5 for the representative case l = 15 + 1. The same scale bar (500 μm) and color bar apply uniformly to all subfigures in Fig. 4. Spatial scale bar (500 μm) and intensity color bar for the representative case l = 15 + 1 from Fig. 4. These calibration parameters apply uniformly to all subfigures in Figs. 4 and 6. As explained in the theoretical analysis section, to generate partially coherent Bessel vortex beams, a time-varying random phase is simultaneously applied to the SLM along with the hologram generation. Consequently, a hologram movie, whose phase changes randomly, is displayed on the SLM. Upon passing the Gaussian laser beam through the SLM, partially coherent Bessel vortex beams are generated. The random phase applied to the SLM follows Kolmogorov’s energy-cascade theory, which was fully detailed in the theoretical analysis section. The frequency of the random phase variations differs depending on the value of the source coherence parameter. For the variation frequency is 30 Hz. The value of must be selected such that the efficiency of the generated partially coherent Bessel vortex beam in the turbulent medium is not significantly reduced. The allowable values obtained for are reported in the results section. Figure 6 shows the hologram and beam images of partially coherent Bessel-Vortex beams (l= 0) and dual Bessel-Vortex beams ( +5, −5), with varying Fried parameters. Hologram and beam images of zero-order Bessel-Vortex beams and partially coherent dual Bessel-Vortex beams (l₁ = +5, l₂ = −7) under different levels of turbulence corresponding to varying Fried parameters. Scale bar (500 μm) and intensity color bar are consistent with those shown in Fig. 5 and apply to all subfigures (r0 in the figure is same as ). Results Having characterized the OTG and generated partially coherent Bessel-Vortex beams via SLM modulation, we now present their measured scintillation response under controlled turbulence, directly linking beam coherence and topological structure to turbulence resilience. When the OTG is off, a random phase was applied to the zero-order Bessel-Vortex beam hologram for different values, and the corresponding scintillation index for each was obtained, as shown in Fig. 7. The scintillation index is given by Eq. (22)15,51,54: Scintillation index as a function of the source coherence parameter (indicated as r0 in the figure) for zero-order Bessel-Vortex beams without simulated atmospheric turbulence. where I is the instantaneous intensity, is the mean intensity, and is the second-order intensity moment at the detector plane. Subsequently, the OTG was activated at a temperature difference of 35 °C ( m–2/3), and the partially coherent Bessel-Vortex beams generated for various values were transmitted through it. Their intensity fluctuations were recorded by a CCD camera. The scintillation index as a function of the parameter for the zero-order Bessel-Vortex beam is shown in Fig. 8. The results indicate that the lowest sensitivity to turbulence occurs at . The results indicate that for small values of (on the order of millimeters), the turbulence effects on the zeroth-order Bessel vortex beam are significant. For values of , the turbulence effects gradually increase again. Scintillation index as a function of the source coherence parameter (indicated as r0 in the figure) for zero-order Bessel-Vortex beams under atmospheric turbulence (Cₙ² = 7.6 × 10⁻¹¹ m⁻²/³, with fixed atmospheric turbulence strength = 3.9 mm). Figure 9 illustrates the effects of atmospheric turbulence induced by the OTG at various temperatures on partially coherent beams with and . The results indicate that, across different temperatures, the sensitivity to turbulence of partially coherent beams with is lower than that for beams with . These results are consistent with the results in Fig. 8. Scintillation index versus temperature for partially coherent Bessel-Vortex beams (l= 0) with source coherence parameter = 100 m and = 500 m (indicated as r0 in the figure) at various OTG temperatures. The effects atmospheric turbulence on partially coherent Bessel-Vortex beams ( =100 m) of different orders are shown in Fig. 10. The results indicate that, as the beam order increases, the sensitivity to turbulence also increases for both fully coherent and partially coherent Bessel-Vortex beams. Scintillation index as a function of the source coherence parameter (indicated as r0 in the figure) for various orders of Bessel-Vortex beams under atmospheric turbulence (Cₙ² = 7.6 × 10⁻¹¹ m⁻²/³, with fixed atmospheric turbulence strength = 3.9 mm). The effects of atmospheric turbulence on dual Bessel-Vortex and dual partially coherent Bessel-Vortex beams () were investigated. Experimental results show that for dual partially coherent Bessel-Vortex beams with co-signed topological charges (m₁ = +1 fixed, m₂ = +1 to + 20), the turbulence resilience increases monotonically as the topological charge difference |Δm| increases (Fig. 11a). For counter-signed topological charges (m₁ = +1 fixed, m₂ = −1 to − 20), the turbulence resilience exhibits a non-monotonic behavior: it decreases to a minimum at |Δm| = 8 and then gradually recovers for larger charge differences (Fig. 11b). Scintillation index as a function of the source coherence parameter (indicated as r0 in the figure) for dual Bessel-Vortex beams and dual partially coherent Bessel-Vortex beams (= 100 m) with a identical and b opposite signs of topological charge under atmospheric turbulence (Cₙ² = 7.6 × 10⁻¹¹ m⁻²/³, with fixed atmospheric turbulence strength = 3.9 mm). a =1, =1 to 20; b =1, = − 1 to − 20. However, for equal but opposite topological charges (|| = ||), a peculiar behavior was observed: the resistance to atmospheric turbulence decreased for orders 1 to 14 and continued to decrease thereafter (Fig. 12). These results enabled the identification of optimal topological charge configurations for mitigating turbulence-induced scintillation. Scintillation index as a function of the source coherence parameter (indicated as r0 in the figure) for dual Bessel-Vortex beams and dual partially coherent Bessel-Vortex beams (with = 100 m) with equal but opposite topological charges (|| = ||) under atmospheric turbulence ( m–2/3). The observed scintillation suppression behaviors can be understood through the interplay of interference effects, phase singularity distribution, and coherence-function topology in dual partially coherent Bessel-Vortex beams. For dual-beam configurations with co-signed topological charges (m₁, m₂ > 0 or m₁, m₂ < 0), constructive interference between the two vortex components enhances energy concentration in the central lobe. This leads to a more robust intensity profile that is less susceptible to turbulence-induced scintillation. As the charge difference |Δm| increases, the constructive overlap becomes more pronounced, resulting in monotonically increasing turbulence resilience. This behavior is consistent with the findings of Refs.28,29, where co-signed vortex pairs demonstrated enhanced stability in turbulent media. In contrast, counter-signed topological charges (m₁ > 0, m₂ < 0 or vice versa) produce destructive interference that creates a characteristic cross-shaped intensity pattern with four intensity lobes. The minimum resilience observed at Δm = 8 corresponds to the configuration where phase singularity density is maximized, creating more vulnerable points for turbulence-induced perturbations. Beyond Δm = 8, the interference pattern stabilizes, leading to a recovery in resilience. This non-monotonic behavior has not been previously reported in the literature and represents a novel finding of this work. Most strikingly, beams with equal-magnitude opposite charges (|m₁| = |m₂|) exhibit complete phase cancellation along the symmetry axis, creating a deep intensity null. As the charge magnitude increases, this null becomes more pronounced and extends radially. Consequently, this configuration displays monotonic degradation in turbulence resilience up to order 14—a behavior absent in single-vortex systems. This anomalous degradation can be attributed to the increasing spatial extent of the phase singularity, which enhances sensitivity to random phase perturbations introduced by atmospheric turbulence. The partial coherence of the source further modifies these interference effects through statistical averaging. The coherence-function topology influences the stability of phase singularities under turbulence, with reduced spatial coherence providing additional robustness by decorrelating turbulence-induced phase fluctuations across the beam profile. This combined effect of topological charge pairing and partial coherence engineering offers a powerful approach for designing turbulence-resilient optical systems beyond what is achievable through either mechanism alone. Conclusion This work introduces two key contributions: first, a novel holographic method for simultaneously encoding Bessel-Vortex phase profiles and Kolmogorov-distributed random phases onto a single SLM display, enabling efficient generation of partially coherent structured light; and second, the discovery that topological charge pairing in dual-beam configurations provides an additional degree of freedom for turbulence mitigation beyond partial coherence alone. Specifically, we demonstrate that turbulence resilience in structured light can be engineered by co-optimizing spatial partial coherence and topological charge pairing. While the turbulence-mitigating role of partial coherence has been well established in prior literature, the key finding of this work is that the relative sign and magnitude of topological charges in dual partially coherent Bessel-Vortex beams critically influence scintillation suppression. Dual-beam configurations with co-signed charges exhibit monotonically increasing resilience with charge difference, whereas counter-signed pairs display a non-monotonic response with a minimum at Δm = 8. Most strikingly, beams with equal-magnitude opposite charges (|m₁| = |m₂|) exhibit monotonic degradation in resilience up to order 14—a behavior absent in single-vortex systems. These results establish that topological charge pairing serves as a powerful and previously unexplored design parameter for turbulence-resilient optical systems. The experimental framework presented here, based on a broadband optical turbulence generator and dynamic SLM-based beam shaping, offers a practical pathway for advancing free-space optical communication, quantum information protocols, and precision optical manipulation in turbulent environments. Author contributions R.A. and M.Y. conceived the research and defined the overarching methodology. J.J. designed and performed the optical experiments, conducted numerical simulations, generated the figures, and prepared the initial draft of the manuscript. M.Y. supervised the writing process, substantially revised the manuscript for scientific clarity and language, and serves as the corresponding author responsible for communication with the journal. All authors discussed the results, contributed to the interpretation, and approved the final version of the manuscript. All authors agree to be personally accountable for their contributions and for ensuring the integrity of the work. Funding This research received no specific grant from any funding agency. Data availability The data that support the findings of this study are available from the corresponding author upon reasonable request. Declarations Competing interests The authors declare no competing interests. Footnotes Publisher’s Note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations. References Associated Data Data Availability Statement The data that support the findings of this study are available from the corresponding author upon reasonable request.