A three-dimensional nonlinear finite element model for coupled vibration analysis of rotary steerable systems Authors: Kun Shao, Yue Liu, Huihui Wang, Lizhi Xiao, Zhengzhi Zhou, Zhanjun Jia, Qichen Sun Published: 2026 ABSTRACT Reliable operation of intelligent rotary steerable systems (RSSs) critically depends on the dynamic stability of the bottom-hole assembly (BHA), where high-frequency vibrations can lead to tool malfunction, accelerating structural fatigue, and degrade steering performance under harsh downhole conditions. This study establishes a three-dimensional nonlinear coupled vibration model for a static push-the-bit RSS–BHA based on finite-element dynamics, energy-based methods, and Hamilton’s principle, enabling a unified analysis of axial, lateral, and torsional vibrations and their coupled responses under field-relevant high-frequency conditions. The results show that the proposed model can identify seven representative vibration modes commonly observed in drilling operations, including single-mode vibrations, pairwise coupled vibrations, and fully coupled vibration behaviors, and its predictive capability is validated through field-based case studies. Distinct dynamic characteristics clearly differentiate torsion-dominated stick–slip vibration from lateral–torsional coupled whirl vibration. Sensitivity analyses further demonstrate that stick–slip vibration is primarily governed by torsional excitation, whereas whirl vibration is dominated by lateral–torsional coupling and exhibits strong sensitivity to rotational speed and drill-collar geometry. Overall, this work provides a quantitative, physics-based framework for vibration-mode identification, interpretation of coupling mechanisms, and mode-specific vibration control and parameter optimization of RSS–BHA systems. Introduction With the increasing demand for complex well trajectories and extended horizontal sections, rotary steerable systems (RSSs) have become a key technology in modern directional and horizontal drilling1–3. By maintaining continuous rotation, RSS enables high trajectory control accuracy and improved borehole quality. However, under high rotational speeds and strongly constrained downhole conditions, the bottom-hole assembly (BHA) of RSS is subjected to multiple excitation sources, including bit–formation interaction, borehole contact, and structural discontinuities4–6, which can give rise to complex vibration responses. Excessive vibrations not only deteriorate borehole quality and reduce the rate of penetration but also accelerate fatigue damage and wear of drilling tools and steering components, thereby compromising tool reliability and operational efficiency. Because RSS–BHA vibrations typically involve coupled axial, lateral and torsional motions with pronounced nonlinear characteristics7–10, accurate characterization and prediction of their vibration responses are essential for vibration risk assessment, drilling parameter optimization, and the safe and efficient application of RSS technology. Drilling dynamic systems exhibit pronounced nonlinearity and strong coupling effect11,12, while downhole boundary conditions are highly complex and continuously evolve with changes in well depth, inclination, and borehole geometry13,14. Under realistic drilling conditions, contact constraints, friction-induced nonlinearities, and time-varying boundaries are inevitably involved, which imposes inherent limitations on conventional analytical and semi-analytical approaches. Consequently, a robust numerical framework is required to accurately capture the complex dynamic behavior of drill-string systems. In this context, the finite element method (FEM) provides a unified framework for representing structural details of drilling tools, borehole contact constraints, and multiple external loadings, and has gradually become one of the most practically applicable numerical approaches for drill-string and BHA dynamic analysis. As early as the 1980s, Millheim and Apostal15–17 developed a three-dimensional dynamic finite element model of drill-strings based on D’Alembert’s principle, laying an important foundation for numerical analysis of drilling vibrations. Subsequent studies18–20 extended this framework by introducing three-dimensional beam elements, time-domain solution strategies, and improved time-integration schemes, thereby enabling the characterization of time-varying dynamic responses of drill-strings and BHAs. With continued advances in numerical computation and modeling techniques, a wide range of element formulations, time-integration algorithms, and force–frequency response analysis methods have been incorporated into finite element models21–23. These developments have enabled more realistic representation of drilling conditions and increasingly detailed descriptions of complex downhole dynamic behavior. Over the past several decades, vibration analysis models for drill-strings and BHAs have been continuously developed and refined. Numerous studies24–27 have demonstrated that the transition of axial load along the drilling system from tensile to compressive states, the strongly coupled nature of bit–rock interaction, high static driving torque, and drill-string curvature are the primary factors responsible for multimodal vibrations and vibration mode coupling. Accordingly, axial–torsional, axial–lateral, torsional–lateral, and fully coupled axial–torsional–lateral vibration models have been preliminary investigated18,28–32. Compared with single-mode analyses, coupled vibration modeling plays a critical role in improving the fidelity of downhole dynamic response prediction. Such models can be formulated in either linear or nonlinear forms, with contact and friction effects often incorporated to better represent field conditions23,28. However, due to the diversity and complexity of geological formations and borehole structures, these coupled models typically rely on expert judgment to define contact relationships, constraints, and boundary loadings33. This reliance increases both modeling and computational complexity and limits their general applicability and computational efficiency in engineering practice. Under (RSSs operating conditions, the complexity and uncertainty of drill-string dynamic behavior are further amplified, making accurate definition of contact relationships, constraints, and boundary conditions considerably more challenging. On the one hand, the RSS–BHA integrates steering actuators, measurement and control units, and multiple structural discontinuities, which substantially increased structural complexity and lead to more intricate boundary conditions3,34. On the other hand, continuous rotation during RSS operations makes the system more susceptible to vibration responses by pronounced high-frequency components and strong multi-degree-of-freedom coupling35,36. From an engineering perspective, prediction of vibration response alone is often insufficient to directly support field decision-making. It is also necessary to relate complex dynamic responses to operationally meaningful vibration types, thereby enabling vibration mode identification and classification for drilling parameter optimization and vibration control. In particular, stick–slip and whirl vibrations37,38, which are frequently observed in the field and pose significant operational risks, represent torsion-dominated nonlinear responses and complex lateral–torsional coupled dynamics, respectively. Their sensitivities to operating conditions and structural parameters differ markedly, underscoring the need for targeted investigations within a unified three-dimensional coupled dynamic framework. Motivated by these considerations, this study develops a three-dimensional nonlinear coupled vibration model for a bottom-hole assembly integrated with an IDS intelligent rotary steerable systems, with the objective of capturing the key characteristics of realistic operating conditions. The model is formulated within a unified framework that combines finite element dynamics, energy-based methods, and Hamilton’s principle, and is employed to identify and classify representative vibration modes. Furthermore, detailed investigations of stick–slip and whirl vibrations are carried out under typical field conditions, followed by a comprehensive sensitivity analysis to systematically evaluate the influence of critical structural and operating parameters on different vibration modes. The results provide a solid quantitative basis for vibration control strategies and drilling-parameter optimization in rotary steerable drilling, thereby enhancing operational safety, reliability, and efficiency. Compared with previous drill-string and BHA finite-element models, the main contribution of the present study is not the isolated use of beam elements or Hamiltonian derivation, but the establishment of an RSS-oriented three-dimensional nonlinear coupled dynamic framework that is directly linked to engineering vibration-mode identification. Specifically, the proposed model integrates axial, two orthogonal lateral, and torsional motions; RSS-specific structural discontinuities and steering-pad actions; nonlinear borehole-contact/friction effects; and bit-rock excitation within one computational framework. This unified formulation enables consistent discrimination of single-mode, pairwise-coupled, and fully coupled vibration states under field-relevant rotary steerable drilling conditions. More importantly, it provides a mode-dependent predictive capability: torsion-dominated stick–slip and lateral-torsional whirl are reproduced within the same physical model and are shown to possess markedly different controlling mechanisms and parameter sensitivities. In this sense, the present work extends previous drill-string FEM studies from response prediction alone toward physics-based vibration-type identification and mode-specific control analysis for RSS–BHA systems. Three-dimensional nonlinear coupled vibration model of the RSS–BHA Physical model The research object of this study is the IDS intelligent RSS developed by China National Petroleum Corporation (CNPC) Logging Company, which belongs to a static push-the-bit RSS39. The drill-string consists of drill pipes extending from the surface and a BHA located at the lower end. As the most dynamically complex component of the downhole system, the BHA is the region where vibrations are most pronounced and serves as the core functional unit for wellbore trajectory control and near-bit data acquisition in rotary steerable drilling3,40. The RSS–BHA consists of drill collars, measurement and communication subs, stabilizers, a rotary steerable sub, and a drill bit, which are connected sequentially along the axial direction, as illustrated in Fig. 1. During drilling, the RSS–BHA is subjected to multiple loads, including weight on bit, torque, and formation reaction forces, which induce axial, lateral, and torsional lateral vibrations. The resulting dynamic response directly affect the operational stability of the RSS and the overall wellbore quality.Fig. 1Schematic of the IDS intelligent RSS- BHA configuration. Schematic of the IDS intelligent RSS- BHA configuration. Mathematical model Coordinate systems and modeling assumptions To describe the spatial configuration and dynamic response of the RSS–BHA during drilling, three mutually related coordinate systems are introduced, as illustrated in Fig. 2. The Cartesian coordinate system O1-END is defined as the global reference frame, where O1 is located at the wellhead center, and E, N, and D denote the east, north, and vertical downward directions, respectively. To represent the spatial geometry of the borehole in the global coordinate system, the borehole is discretized along the axial direction into segments with an interval of 30 m. Each borehole segment is approximated as a cylindrical section, as shown in Fig. 2a. The Cartesian coordinate system O2-XYZ is defined as the borehole coordinate system, where O2 is located at the center of the borehole cross section. The Z-axis is aligned with the borehole axis, and the Y-axis points toward the high-side direction of the borehole.Fig. 2Definition of coordinate systems and finite element discretization. Definition of coordinate systems and finite element discretization. Based on the above descriptions, the RSS–BHA is discretized along the axial direction into n finite elements, as shown in Fig. 2b. A Cartesian coordinate system o3-xyz is introduced as the local coordinate system of each element, where o3 is located at the center of the cross section, and the z-axis is aligned with the element axial direction, as illustrated in Fig. 2c. Each discretized segment is modeled as a three-dimensional elastic beam element. Taking the eth beam element as an example (Fig. 2c), its deformation state is uniquely determined by the translational displacements and rotational angles at the two end nodes, i and j. Accordingly, the generalized displacement vector of the element can be expressed as:1\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\mathbf{q}}^{e} = [u_{i} ,v_{i} ,w_{i} ,\theta_{xi} ,\theta_{yi} ,\varphi_{i} ,u_{j} ,v_{j} ,w_{j} ,\theta_{xj} ,\theta_{yj} ,\varphi_{j} ] \, ^{T}$$\end{document}where the subscript i indicates the left node, while the subscript j indicates the right node. u and v denote the transverse displacements of the node along the local x- and y-directions, respectively, while w represents the axial displacement along the local z-direction. u, v and w are functions of coordinating z and time t. The rotation angles θx and θy correspond to bending rotations about the local x- and y-axes, respectively, and θz denotes the torsional rotation about the local z-axis. Under the Euler–Bernoulli beam assumption41, the cross section remains plane and always perpendicular to the deformed neutral axis, and shear deformation is neglected. Consequently, the bending rotations are related to the first-order derivatives of the transverse displacements with respect to the axial coordinate as follows:2a\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{array}{*{20}c} {\theta_{x} = \frac{\partial v}{{\partial z}},} & {\theta_{y} = - \frac{\partial u}{{\partial z}},} & {\theta_{z} = \frac{\partial \phi }{{\partial z}}} \\ \end{array}$$\end{document}where, θx and θy are functions of the lateral displacements u and v respectively. φ represents the torsional rotation angle, which is a function of the coordinate z and time t, as illustrated in Fig. 2d. A cross-section taken at the ith node. Point O2 represents the origin of the wellbore coordinate system, point O3 denotes the centroid of the drill string cross-section at the ith node, and point C indicates the center of gravity of the cross-section. To clarify the applicability boundary of Eq. (2a), the above Euler–Bernoulli relation is used in this study as a compact baseline kinematic description for slender drill-pipe segments and for the dominant low-order coupled responses emphasized in the present RSS–BHA analysis. For drill-collar-dominated short/thick segments and for higher-frequency local responses, however, transverse shear deformation and rotary inertia may become non-negligible. In that case, a Timoshenko-type extension can be introduced through the transverse shear strains42–44. \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\gamma}_{xz}$$\end{document} and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\gamma}_{yz}$$\end{document} represent the transverse shear strains:2b\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\gamma_{xz} = \frac{\partial u}{{\partial z}} - \theta_{y} ,\;\;\gamma_{yz} = \frac{\partial v}{{\partial z}} - \theta_{x}$$\end{document}and the corresponding additional shear strain energy of the eth beam element \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${U}_{s}^{\left(e\right)}$$\end{document} can be written as2c\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$U_{s}^{\left( e \right)} = \frac{1}{2}\mathop \smallint \limits_{0}^{le} \kappa_{e} G_{e} A_{e} \left( {\gamma_{xz}^{2} + \gamma_{yz}^{2} } \right)dz$$\end{document}where le is unit length, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\kappa}_{e}$$\end{document} is the shear correction factor of the cross-section, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${G}_{e}$$\end{document} is the shear modulus, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${A}_{e}$$\end{document} is the unit cross-sectional area. For a hollow circular drill-string section, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\kappa}_{e}$$\end{document} may be evaluated following the hollow-section shear-correction treatment summarized by Cowper and adopted in the Wilson drillstring formulation42,43. Additional kinetic energy due to the rotational inertia of the e-th beam element \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${T}_{r}^{\left(e\right)}$$\end{document} is2d\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$T_{r}^{\left( e \right)} = \frac{1}{2}\mathop \smallint \limits_{0}^{le} \rho_{e} \left( {I_{x,e} \dot{\theta}_{x}^{2} + I_{y,e} \dot{\theta}_{y}^{2} } \right)dz$$\end{document}where \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\rho}_{e}$$\end{document} is unit material density, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${I}_{x,e}$$\end{document} and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${I}_{y,e}$$\end{document} is sectional moment of inertia about the local x and y axes, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\dot{\theta }}_{x}$$\end{document} and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\dot{\theta }}_{y}$$\end{document} is the first derivative of the rotation angle around the local x and y axes with respect to time, i.e., the angular velocity component. Equation (2d) supplements the translational kinetic energy in the higher-frequency range. In the present study, the compact Euler–Bernoulli relation is retained for concise derivational presentation of the global RSS–BHA response, whereas the above Timoshenko correction is now explicitly stated to interpret the possible deviation in thick drill-collar sections and high-frequency local dynamics. Consistent three-dimensional Timoshenko interpolation may further be introduced to avoid shear locking in practical finite-element implementation42,44. Assuming that the displacement of the cross-section centroid in the wellbore coordinate system (O2-XYZ) is given by (u, v, w), the displacement of the center of gravity of the drill string cross-section at the ith node can be expressed as:3\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\vec{r}_{c} = \left[ {u + e\cos \left( {\phi + \alpha_{0} } \right)} \right]\vec{i} + \left[ {v + e\sin \left( {\phi + \alpha_{0} } \right)} \right]\vec{j} + w\vec{k}$$\end{document}where e (m) denotes the eccentric distance between the centroid O3 and the center of gravity C and α0 is the initial eccentric angle (rad). The vectors \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\vec{i},\vec{j}$$\end{document} and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\vec{k}$$\end{document} are unit vectors along the X-, Y-, and Z -axes, respectively. By taking the first derivative of Eq. (3) with respect to time t, the velocity Vp (m/s) of the drill-string centroid is obtained as:4\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$V_{p} = \frac{{d\vec{r}_{c} }}{dt} = \left[ {\dot{u} - e\sin \left( {\phi + \alpha_{0} } \right)\dot{\phi }} \right]\vec{i} + \left[ {\dot{v} + e\cos \left( {\phi + \alpha_{0} } \right)\dot{\phi }} \right]\vec{j} + \dot{w}\vec{k}$$\end{document}where \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\dot{u},\dot{v},\dot{w}$$\end{document} and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\dot{\varphi }$$\end{document} represent the first-order time derivatives of u, v, w and φ, respectively. To establish a solvable three-dimensional nonlinear coupled vibration model, the following basic assumptions are adopted for the RSS–BHA system:The borehole cross section is assumed to be circular. The borehole wall is treated as a continuous, homogeneous, and rigid structure without deformation, and its axis coincides with the borehole centerline.The RSS–BHA is modeled as a three-dimensional elastic beam structure. The material is assumed to be homogeneous, isotropic, and linearly elastic. Gravity is uniformly distributed along the entire length of the RSS–BHA.The contacts between the steering pads of the rotary steerable sub, the stabilizers, and the borehole wall are simplified as point contacts. The normal reaction forces from the borehole wall are denoted as Fn1 and Fn2, respectively (see Fig. 2a). The contact interaction between the RSS–BHA and the borehole wall is described using a penalty stiffness approach, with optional contact damping, and the contact–separation state is updated dynamically with time.The drill bit is simplified as a hinged support, with its center aligned with the borehole centerline. Bit enlargement and bending moments are neglected. The axial force exerted by the formation on the bit is denoted as Fα, and the lateral force is denoted as Fl (see Fig. 2a). The borehole cross section is assumed to be circular. The borehole wall is treated as a continuous, homogeneous, and rigid structure without deformation, and its axis coincides with the borehole centerline. The borehole cross section is assumed to be circular. The borehole wall is treated as a continuous, homogeneous, and rigid structure without deformation, and its axis coincides with the borehole centerline. The RSS–BHA is modeled as a three-dimensional elastic beam structure. The material is assumed to be homogeneous, isotropic, and linearly elastic. Gravity is uniformly distributed along the entire length of the RSS–BHA. The RSS–BHA is modeled as a three-dimensional elastic beam structure. The material is assumed to be homogeneous, isotropic, and linearly elastic. Gravity is uniformly distributed along the entire length of the RSS–BHA. The contacts between the steering pads of the rotary steerable sub, the stabilizers, and the borehole wall are simplified as point contacts. The normal reaction forces from the borehole wall are denoted as Fn1 and Fn2, respectively (see Fig. 2a). The contact interaction between the RSS–BHA and the borehole wall is described using a penalty stiffness approach, with optional contact damping, and the contact–separation state is updated dynamically with time. The contacts between the steering pads of the rotary steerable sub, the stabilizers, and the borehole wall are simplified as point contacts. The normal reaction forces from the borehole wall are denoted as Fn1 and Fn2, respectively (see Fig. 2a). The contact interaction between the RSS–BHA and the borehole wall is described using a penalty stiffness approach, with optional contact damping, and the contact–separation state is updated dynamically with time. The drill bit is simplified as a hinged support, with its center aligned with the borehole centerline. Bit enlargement and bending moments are neglected. The axial force exerted by the formation on the bit is denoted as Fα, and the lateral force is denoted as Fl (see Fig. 2a). The drill bit is simplified as a hinged support, with its center aligned with the borehole centerline. Bit enlargement and bending moments are neglected. The axial force exerted by the formation on the bit is denoted as Fα, and the lateral force is denoted as Fl (see Fig. 2a). Governing equations for three-dimensional nonlinear coupled vibration Based on the kinematic description of the three-dimensional elastic beam elements, the strain energy, kinetic energy, and external work of the RSS–BHA system are formulated within a unified coordinate framework. By introducing an energy-based approach and applying Hamilton’s principle, the dynamic behavior of the system is systematically modeled, and the governing equations describing the three-dimensional nonlinear coupled vibration of the RSS–BHA are derived. These governing equations simultaneously characterize the coupling among axial, two orthogonal lateral, and torsional vibrations, and provide the theoretical foundation for subsequent finite element discretization, numerical solution, and vibration mode analysis. Strain energy Strain energy Strain energy The total strain energy Ud of an RSS–BHA beam element consists of the strain energy contributions induced by axial, lateral bending, and torsional deformations, as well as their corresponding coupling terms. The axial strain energy, lateral bending strain energy, and torsional strain energy are denoted by Uz, Uw and Uφ, respectively. The axial–lateral, axial–torsional, and lateral–torsional coupling strain energies are denoted by Uzw, Uzφ, and Uwφ, respectively. Accordingly, the total strain energy of the eth beam element can be expressed as follows:5\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$U_{d}^{\left( e \right)} = U_{z}^{\left( e \right)} + U_{w}^{\left( e \right)} + U_{\varphi }^{\left( e \right)} + U_{zw}^{\left( e \right)} + U_{z\varphi }^{\left( e \right)} + U_{w\varphi }^{\left( e \right)} + U_{{\mathrm{s}}}^{\left( e \right)}$$\end{document} Here,6\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$U_{z}^{\left( e \right)} = \frac{1}{2}\;\int_{0}^{{l_{e} }} {E_{e} A_{e} (w^{\prime})^{2} } dz$$\end{document}7\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$U_{w} ^{{\left( e \right)}} = \frac{1}{2}\int_{0}^{{l_{e} }} {E_{e} I_{e} \left[ {(u^{{\prime \prime }} )^{2} + (v^{{\prime \prime }} )^{2} } \right]} dz$$\end{document}8\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$U_{\varphi }^{\left( e \right)} = \frac{1}{2}\;\int_{0}^{{l_{e} }} {G_{e} J_{e} \;(\varphi {^\prime} )^{2} dz}$$\end{document}9\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$U_{zw} = \frac{1}{2}\int_{0}^{{l_{e} }} {E_{e} A_{e} w^{\prime } (u^{\prime 2} + v^{\prime 2} )dz}$$\end{document}10\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$U_{z\varphi } = \int_{0}^{{l_{e} }} {E_{e} I_{e} w^{\prime } \;(\varphi {^\prime} )^{2} dz}$$\end{document}11\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$U_{{w\varphi }} = \int_{0}^{{l_{e} }} {E_{e} I_{e} \varphi ^{\prime } (u^{\prime } v^{{\prime \prime }} - u^{{\prime \prime }} v^{\prime } )dz}$$\end{document}where, le denotes the element length (m); Ae is the cross-sectional area (m2); Ee is Young’s modulus (Pa); the second moment of area Ie can be decomposed into Ix,e and Iy,e (m4); Ge denotes the shear modulus (Pa); Je is the polar moment of inertia (m4); φ represents the torsional angle (rad). The superscripts ', '', ''', '''' denote the first-, second-, third-, and fourth-order derivatives of the function with respect to the axial coordinate z, respectively. (2)Kinetic energy (2)Kinetic energy Kinetic energy The total kinetic energy Td(e) of an RSS–BHA beam element consists of the translational kinetic energy Ep(e) and the rotational kinetic energy Ez(e), and can be expressed as follows:12\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$T_{d}^{\left( e \right)} = E_{p}^{\left( e \right)} + E_{z}^{\left( e \right)} + T_{{\mathrm{r}}}^{\left( e \right)}$$\end{document} Here,13\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$E_{p}^{\left( e \right)} = \frac{1}{2}\int_{0}^{{l_{e} }} {\rho_{e} A_{e} V_{p}^{2} dz}$$\end{document}14\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$E_{z}^{\left( e \right)} = \frac{1}{2}\;\int_{0}^{{l_{e} }} {\rho_{e} J_{p,e} \dot{\varphi }^{2} dz}$$\end{document}where, ρe denotes the material density (kg/m3); Jp,e represents the mass polar moment of inertia of the cross section about the z-axis (kg/m2). (3)External work (3)External work External work The total external work Wd(e) of an RSS–BHA beam element consists of the axial external work Wz(e), the lateral external work Wxy(e), and the torsional external work Wφ(e), and can be expressed as follows:15\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$W_{d}^{\left( e \right)} = W_{z}^{\left( e \right)} + W_{xy}^{\left( e \right)} + W_{\varphi }^{\left( e \right)}$$\end{document} Here,16\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$W_{z}^{\left( e \right)} = \int_{0}^{{l_{e} }} {F_{z} w \, dz}$$\end{document}17\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$W_{xy}^{\left( e \right)} = \int_{0}^{{l_{e} }} {(F_{x} u + F_{y} v) \, } dz$$\end{document}18\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$W_{\varphi }^{{\left( e \right)}} = \int_{0}^{{l_{e} }} {[T_{\varphi } (\varphi + u^{\prime } \;v^{{\prime \prime }} - v^{\prime } u^{{\prime \prime }} )]} dz$$\end{document}where, Fz denotes the axial load (N); Fx and Fy denote the lateral loads (N); Tφ denotes the applied torque (N m). Within the unified energy framework composed of the strain energy, kinetic energy, and external work, the dynamic governing equations of the system can be derived using a variational approach. According to Hamilton’s principle, which can be expressed as follows:19\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\delta \int_{{t_{1} }}^{{t_{2} }} {(T_{d} - U_{d} + W_{d} \;)} \, dt = 0$$\end{document} By substituting Eqs. (1)–(18) into Eq. (19), and taking variations with respect to the axial displacement w, the lateral displacements u and v, and the torsional angle φ, the governing equations describing the three-dimensional nonlinear coupled vibration behavior of the RSS–BHA are obtained.20\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left\{ {\begin{array}{*{20}l} {\rho_{e} A_{e} u^{\prime \prime } - E_{e} A_{e} (w^{\prime \prime } u^{\prime } + w^{\prime } u^{\prime \prime } ) + E_{e} I_{e} u^{\prime \prime \prime \prime } + T_{\varphi } v^{\prime \prime \prime } = F_{x} } \hfill \\ {\rho_{e} A_{e} v^{\prime \prime } - E_{e} A_{e} (w^{\prime \prime } v^{\prime } + w^{\prime } v^{\prime \prime } ) + E_{e} I_{e} v^{\prime \prime \prime \prime } - T_{\varphi } u^{\prime \prime \prime } = F_{y} } \hfill \\ { - \rho_{e} A_{e} w^{\prime \prime } + E_{e} A_{e} (u^{\prime } u^{\prime \prime } + v^{\prime } v^{\prime \prime } ) + E_{e} A_{e} w^{\prime \prime } + 2E_{e} I_{e} \varphi^{\prime } \varphi^{\prime \prime } = F_{z} } \hfill \\ {\rho_{e} J_{e} \varphi^{\prime \prime } - 2E_{e} I_{e} (w^{\prime \prime } \varphi^{\prime } + w^{\prime } \varphi^{\prime \prime } ) - G_{e} J_{e} \varphi^{\prime \prime } = T_{\varphi } } \hfill \\ \end{array} } \right.$$\end{document} The three-dimensional nonlinear characteristics exhibited by the governing equations mainly originate from geometric nonlinear deformations and bending–torsion coupling effects induced in the RSS–BHA during drilling operations. Specifically, the nonlinear coupling terms between the axial and lateral displacements (e.g., \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$w^{\prime\prime}u^{\prime}$$\end{document}, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$w^{\prime}u^{\prime\prime}$$\end{document} and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$u^{\prime}u^{\prime\prime}$$\end{document}) arise from the Green–Lagrange strain formulation under large-deflection bending conditions. These terms represent the additional axial strain induced by bending deformation and constitute typical geometric nonlinearities in slender-beam dynamics. In contrast, the coupling terms between the torsional angle and the lateral displacements (e.g., \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$w^{\prime\prime}\varphi^{\prime}$$\end{document}, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$w^{\prime}\varphi^{\prime\prime}$$\end{document}, as well as the additional terms introduced by \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\varphi^{\prime}\left( {u^{\prime}v^{\prime\prime} - u^{\prime\prime}v^{\prime}} \right)$$\end{document}) stem from the coupling between cross-sectional rotation and bending curvature, reflecting the nonlinear interaction between bending and torsional motions. The combined effects of these nonlinear terms lead to complex multi-degree-of-freedom and multimodal coupled vibration characteristics of the RSS–BHA under rotary steerable drilling conditions. Loads and boundary conditions During downhole drilling operations, the dynamic response of the RSS–BHA is governed by multiple types of loads, including gravitational loads, borehole wall contacts loads, and bit–formation interaction forces. These loads act as external excitations in the governing equations of the three-dimensional nonlinear coupled vibration and play a crucial role in determining the system dynamic behavior. To ensure the computational tractability and engineering applicability of the proposed dynamic model, the different types of loads are modeled separately, and the boundary conditions required for the dynamic solution are specified accordingly. Loads/external excitation terms Loads/external excitation terms Loads/external excitation terms Gravitational load Gravitational load Gravitational load The self-weight of the RSS–BHA is distributed along its spatial orientation and can be decomposed into components along different directions in the borehole coordinate system O2-XYZ. For the eth beam element, the gravitational load components along each coordinate direction can be expressed as follows:21\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left\{ {\begin{array}{*{20}l} {m_{X}^{\left( e \right)} = 0} \hfill \\ {m_{Y}^{\left( e \right)} = \rho_{e} gl_{e} \sin (\beta_{e} )} \hfill \\ {m_{Z}^{\left( e \right)} = \rho_{e} gl_{e} \cos (\beta_{e} )} \hfill \\ \end{array} } \right.$$\end{document} If the RSS–BHA consists of n finite elements, the total gravitational load can be obtained by summing the axial components of the gravitational forces acting on all beam elements, which can be expressed as follows:22\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$F_{g} = \sum\limits_{i = 1}^{n} {m_{Z}^{\left( e \right)} \;}$$\end{document}where, mX(e) and mY(e) denote the gravitational force components along the lateral directions of the element (N); mz(e) represents the component along the element axial direction, which is used to determine the effective weight on bit and the axial stress distribution (N); g denotes the gravitational acceleration (m s−2). 2)Contact loads 2)Contact loads Contact loads During rotary steerable drilling, the RSS–BHA may come into contact with the borehole wall at multiple locations. Typical contact configurations are illustrated in Fig. 3. The active contact between the steering pads of the rotary steerable sub and the borehole wall is shown in Fig. 3a, whereas the passive contacts involving the stabilizers, drill collars, and drill pipe are shown in Fig. 3b.Fig. 3Typical contact configurations between the RSS–BHA and the borehole wall: (a) Steering pads and borehole wall; (b) Stabilizers, drill collars, and drill pipe. Typical contact configurations between the RSS–BHA and the borehole wall: (a) Steering pads and borehole wall; (b) Stabilizers, drill collars, and drill pipe. For static push-the-bit rotary steerable systems, the contact force between the steering pads and the borehole wall is regulated by the surface control unit. Assuming a constant friction coefficient μ between the steering pad and the borehole wall, the tangential friction force acting on the ith steering pad can be expressed as follows:23\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$F_{b}^{i} = \mu F_{l}^{i}$$\end{document}where, Fbi denotes the tangential friction force (N), and Fli denotes the normal force (N). Assuming that the RSS–BHA is equipped with n steering pads, and that the radial direction of the ith steering pad forms an angle θi with the X-axis, the contact load exerted by the borehole wall on the steering pad can be decomposed into components along the X- and Y-directions, as given in Eq. (24).24\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$F_{X}^{b} = \sum\limits_{i = 1}^{n} {\left( {F_{l}^{i} \cos \theta_{i} - F_{b}^{i} \sin \theta_{i} } \right)} , \, F_{Y}^{b} = \sum\limits_{i = 1}^{n} {\left( {F_{l}^{i} \sin \theta_{i} + F_{b}^{i} \cos \theta_{i} } \right)}$$\end{document} Neglecting the elastic deformation and recovery processes of both the RSS–BHA and the borehole wall, the contact behavior between the stabilizers, drill collars, drill pipe, and the borehole wall is described using a lumped nodal contact stiffness model. The radial clearance between the RSS–BHA and the borehole wall at the ith contact node is denoted by δi, as defined in Eq. (25), where d0 is the borehole diameter (m) and di is the outer diameter of the RSS–BHA.25\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\delta_{i} = \left| {\sqrt {u_{i}^{2} + v_{i}^{2} } - {{\left( {d_{0} - d_{i} } \right)} \mathord{\left/ {\vphantom {{\left( {d_{0} - d_{i} } \right)} 2}} \right. \kern-0pt} 2}} \right|$$\end{document} When \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\delta_{i} < 0$$\end{document}, no contact occurs between the RSS–BHA and the borehole wall. When \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\delta_{i} \ge 0$$\end{document}, contact forces are generated, and the corresponding normal and friction forces are given as follows:26\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$F_{l}^{i} = k_{c} \delta_{i}$$\end{document}27\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$F_{a}^{i} = f_{a} F_{l}^{i}$$\end{document}28\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$F_{b}^{i} = f_{r} F_{l}^{i}$$\end{document}where, kc denotes the normal contact stiffness coefficient; Fli is the normal force (N); fa is the axial friction coefficient; Fai is the axial friction force (N); fr is the tangential friction coefficient; Fbi is the tangential friction force (N). The frictional torque induced by the tangential friction force, denoted as Mfi, can be calculated using Eq. (29).29\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$M_{f}^{i} = \frac{1}{2}\;F_{b}^{i} d_{i}$$\end{document} The normal force and tangential friction force are projected onto the lateral load components Fx and Fy, while the axial friction force is introduced as an additional resistance term in the axial equilibrium equation. The frictional torque generated by the tangential friction force contributes to the torsional load term Tφ. Through these mechanisms, contact–friction-induced nonlinear effects are incorporated into the dynamic governing equations. To ensure the robustness of numerical simulation calculations and meet the needs of real-time computation, the contact between the drill string and the wellbore wall is simplified in this paper. Specifically, assuming the wellbore to be circular and rigid, the contact between the drill string and the wellbore wall is represented by a concentrated point contact with penalty stiffness, and the axial friction coefficient and tangential friction coefficient are taken as constants. The aforementioned formula can effectively capture the main nonlinearity induced by contact, intermittent contact-separation behavior, and the mode transition trend between relatively stable rotation, stick–slip, and whirl responses. However, it ignores the effects of irregular wellbore, local flexibility of the wellbore wall, and lubricity of the drilling fluid. Therefore, this model is expected to reproduce the main trends and relative intensities of contact-controlled vibration modes, while neglecting the local impact and extremely high-frequency components of the drill string whirl response. 3)Rock-breaking loads 3)Rock-breaking loads Rock-breaking loads During the rock-breaking process, the drill bit is subjected to axial forces, lateral forces, and torque. These loads act as important external excitation terms and directly influence the dynamic response of the RSS–BHA. To obtain a mechanically interpretable and numerically tractable formulation, the bit–rock interaction is equivalently described using a single-cutter PDC model. In this study, the single-cutter PDC cutting model proposed in Ref.45,46 is adopted, and the overall bit loads are obtained by superposition of the forces acting on individual cutters. As illustrated in Fig. 4, a bit coordinate system o4-x4y4z4 is defined, where the x4-axis corresponds to the reference direction of the first cutter and the z4-axis is aligned with the bit axis. For the kth PDC cutter, a local planar coordinate system o4-RH is established, in which the R-axis forms a circumferential angle θk with the x4-axis, and the H-axis coincides with the z4-axis. The radial and height coordinates of the cutter are denoted by Rk and Hk, respectively, while γk and βk represent the normal angle and side rake angle of the cutter.Fig. 4Schematic of rock-breaking force analysis for the RSS–BHA system: (a) Force analysis of the drill bit; (b) Two-dimensional view (bottom–top). Schematic of rock-breaking force analysis for the RSS–BHA system: (a) Force analysis of the drill bit; (b) Two-dimensional view (bottom–top). The normal force \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$F_{n}^{k}$$\end{document} and the cutting force \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$F_{c}^{k}$$\end{document} acting on the kth PDC cutter can be expressed as follows:30\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left\{ {\begin{array}{*{20}c} {F_{n}^{k} = a_{1} A + b_{1} } \\ {F_{c}^{k} = a_{2} A + b_{2} } \\ \end{array} } \right.$$\end{document}where, A denotes the cutter contact area (m−2). The coefficients a1, b1, a2 and b2 depend on the back rake angle α, the cutting velocity Vs (m/s), and the rock drillability index Kd, which can be given as follows:31\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left\{ {\begin{array}{*{20}l} {a_{1} = (0.03\alpha^{2} - 0.07\alpha + 11.84)(2.31K_{d} - 8.87)(0.43\ln V_{s} + 0.81)} \hfill \\ {b_{1} = (0.19\alpha^{2} - 5.34\alpha + 321.83)(1.10K_{d} - 3.38)(0.04\ln V_{s} + 0.08)} \hfill \\ {a_{2} = (0.01\alpha^{2} - 1.29\alpha + 11.23)(2.12K_{d} - 7.83)(0.44\ln V_{s} + 0.82)} \hfill \\ {b_{2} = (0.0\alpha^{2} + 0.03\alpha + 96.39)(0.31K_{d} - 0.60)(0.04\ln V_{s} + 0.07)} \hfill \\ \end{array} } \right.$$\end{document} In the bit coordinate system, the forces acting on the kth cutter are decomposed into the axial component Fvk, the tangential component Frk, and the radial component Frrk, which can be given as follows:32\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left\{ {\begin{array}{*{20}l} {F_{v}^{k} = F_{n}^{k} \cos \gamma_{k} } \hfill \\ {F_{r}^{k} = F_{n}^{k} \sin \gamma_{k} } \hfill \\ {_{rr}^{k} = F_{c}^{k} \tan \gamma_{k} } \hfill \\ \end{array} } \right.$$\end{document} Assuming that the PDC bit is equipped with m cutters, the overall axial force Fz, lateral forces Fx and Fy, and the torque Tφ acting on the bit can be obtained by summing the contributions from all cutters, which can be given as follows:33\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left\{ {\begin{array}{*{20}l} {F_{z} = \sum\limits_{k = 1}^{m} {F_{v}^{k} = \sum\limits_{k = 1}^{m} {F_{n}^{k} \cos \gamma_{k} } } } \hfill \\ {F_{x} = \sum\limits_{k = 1}^{m} {\left( {F_{c}^{k} \sin \theta_{k} - \left( {F_{r}^{k} + F_{rr}^{k} } \right)\cos \theta_{k} } \right) = \sum\limits_{k = 1}^{m} {\left( {F_{c}^{k} \sin \theta_{k} - \left( {F_{n}^{k} \sin \gamma_{k} + F_{rc}^{k} \tan \beta_{k} } \right)\cos \theta_{k} } \right)} } } \hfill \\ {F_{y} = \sum\limits_{k = 1}^{m} {\left( {F_{c}^{k} \cos \theta_{k} + \left( {F_{r}^{k} + F_{rr}^{k} } \right)\sin \theta_{k} } \right) = \sum\limits_{k = 1}^{m} {\left( {F_{c}^{k} \cos \theta_{k} + \left( {F_{n}^{k} \sin \gamma_{k} + F_{rc}^{k} \tan \beta_{k} } \right)\sin \theta_{k} } \right)} } } \hfill \\ {T_{\varphi } = \sum\limits_{k = 1}^{m} {F_{v}^{k} R_{k} = \sum\limits_{k = 1}^{m} {F_{n}^{k} \cos \gamma_{k} R_{k} } } } \hfill \\ \end{array} } \right.$$\end{document} The axial force, lateral forces, and torque generated during the rock-breaking process are introduced as external excitation terms into the three-dimensional nonlinear coupled vibration governing equations. (2)Boundary and initial conditions (2)Boundary and initial conditions Boundary and initial conditions To ensure the solvability of the three-dimensional nonlinear coupled vibration governing equations, the boundary conditions and initial state of the RSS–BHA system are specified. The well-posed conditions are jointly determined by the geometric constraints at the bit and the wellhead, as well as the corresponding operational inputs. At the bit end, it is assumed that no hole enlargement occurs during drilling. The lateral displacement of the bit is therefore constrained by the borehole geometry, leading to the lateral displacement boundary conditions are given as follows:34\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$u{(0, }t{) = 0,}\;\;v{(0, }t{) = 0}$$\end{document} The axial and torsional motions of the bit are characterized by equivalent measurement inputs provided by the rotary steerable system, and the corresponding axial displacement and torsional angle are specified as follows:35\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$w(0,t) = \int {\int_{{t_{1} }}^{{t_{2} }} {g_{z} (t)} } \, dt, \, \varphi (0,t) = \int_{{t_{1} }}^{{t_{2} }} {\psi_{a} (t)} \, dt$$\end{document} At the wellhead, the lateral displacement of the upper end of the drill-string is constrained by the rotary table structure, and the corresponding boundary condition is given as follows:36\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$u\left( {L,t} \right) = 0, \, v\left( {L,t} \right) = 0$$\end{document} The axial and torsional motions at the wellhead are prescribed by the drilling rate and rotational speed measured at the surface, and the equivalent boundary conditions are expressed as follows:37\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$w(L,t) = \int_{{t_{1} }}^{{t_{2} }} {V_{z} (t)} \, dt,\;\;\varphi (L,t) = \varphi_{a}$$\end{document} At the initial time t = 0, the RSS–BHA is assumed to be in static equilibrium under the combined action of the weight on bit, self-weight, and wellhead loads. This equilibrium configuration is taken as the initial configuration for dynamic analysis. The initial displacement at any position along the system is given as follows:38\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$u\left( {z,0} \right) = u_{0} , \, v\left( {z,0} \right) = v_{0} , \, w\left( {z,0} \right) = w_{0} , \, \varphi \left( {z,0} \right) = \varphi_{0}$$\end{document} In addition, the system is assumed to be initially at rest, such that the initial velocities in all degrees of freedom are zero.39\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\dot{u}\left( {z,0} \right) = \dot{v}\left( {z,0} \right) = \dot{w}\left( {z,0} \right) = \dot{\varphi }\left( {z,0} \right) = 0$$\end{document} Finite element discretization and numerical solution To solve the governing equations of the three-dimensional nonlinear coupled vibration of the RSS–BHA (Eq. 20), the FEM theory is employed to discretize the axial, lateral, and torsional degrees of freedom. The RSS–BHA is discretized along the axial direction into a series of three-dimensional beam elements. Each element is modelled as a two-node three-dimensional beam. Each node has six degrees of freedom, including three translational (u, v, w) and three rotational (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\theta_{x} ,\theta_{y} ,\varphi$$\end{document})degrees of freedom, resulting in a total of 12 degrees of freedom per element. This formulation enables a complete representation of bending, torsion, and their coupling deformations. At the element level, the lateral displacements u and v are interpolated using cubic Hermite shape functions, whereas the axial displacement w and the torsional angle φ are interpolated using linear Lagrange shape functions. The unified interpolation form is given as follows:40\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$u = \psi_{1}^{T} {\mathbf{d}}, \, v = \psi_{2}^{T} {\mathbf{d}}, \, w = \psi_{3}^{T} {\mathbf{d}}, \, \varphi = \psi_{4}^{T} {\mathbf{d}},$$\end{document}where \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\mathbf{d}}$$\end{document} denotes the element nodal generalized displacement vector and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\psi_{i}$$\end{document} represents the corresponding shape function vector. The explicit expressions of the shape functions are provided as follows:41\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left[ {\begin{array}{*{20}c} {\mathbf{d}} \\ {\psi_{1} } \\ {\psi_{2} } \\ \begin{gathered} \psi_{3} \hfill \\ \psi_{4} \hfill \\ \end{gathered} \\ \end{array} } \right]^{T} = \left( {\left[ {\begin{array}{*{20}c} {u_{1} } \\ {u_{1}^{\prime } } \\ {v_{1} } \\ {v_{1}^{\prime } } \\ {w_{1} } \\ {\varphi_{1} } \\ {u_{2} } \\ {u_{2}^{\prime } } \\ {v_{2} } \\ {v_{2}^{\prime } } \\ {w_{1} } \\ {\varphi_{1} } \\ \end{array} } \right]\left[ {\begin{array}{*{20}c} {1 - \frac{{3z^{2} }}{{l^{2} }} + \frac{{2z^{3} }}{{l^{3} }}} \\ {z - \frac{{2z^{2} }}{l} + \frac{{z^{3} }}{{l^{3} }}} \\ 0 \\ 0 \\ 0 \\ 0 \\ {\frac{{3z^{2} }}{{l^{2} }} - \frac{{2z^{3} }}{{l^{3} }}} \\ { - \frac{{2z^{2} }}{l} + \frac{{z^{3} }}{{l^{3} }}} \\ 0 \\ 0 \\ 0 \\ 0 \\ \end{array} } \right]\left[ {\begin{array}{*{20}c} 0 \\ 0 \\ {1 - \frac{{3z^{2} }}{{l^{2} }} + \frac{{2z^{3} }}{{l^{3} }}} \\ {z - \frac{{2z^{2} }}{l} + \frac{{z^{3} }}{{l^{3} }}} \\ 0 \\ 0 \\ 0 \\ 0 \\ {\frac{{3z^{2} }}{{l^{2} }} - \frac{{2z^{3} }}{{l^{3} }}} \\ { - \frac{{2z^{2} }}{l} + \frac{{z^{3} }}{{l^{3} }}} \\ 0 \\ 0 \\ \end{array} } \right]\left[ {\begin{array}{*{20}c} 0 \\ 0 \\ 0 \\ 0 \\ {1 - \frac{z}{l}} \\ 0 \\ 0 \\ 0 \\ 0 \\ 0 \\ \frac{z}{l} \\ 0 \\ \end{array} } \right]\left[ {\begin{array}{*{20}c} 0 \\ 0 \\ 0 \\ 0 \\ 0 \\ {1 - \frac{z}{l}} \\ 0 \\ 0 \\ 0 \\ 0 \\ 0 \\ \frac{z}{l} \\ \end{array} } \right]} \right)$$\end{document} By substituting the displacement interpolation functions into the three-dimensional nonlinear coupled governing equations and applying the variational energy principle, the element-level dynamic equations are derived. After assembling all elements, the global discretized dynamic equation of the RSS–BHA system is obtained as follows:42\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\mathbf{M\ddot{U}}} + {\mathbf{C\dot{U}}} + {\mathbf{KU}} = {\mathbf{F}}$$\end{document}where, U denotes the global displacement vector; F is the equivalent external load vector; M, C and K are the global mass, damping, and stiffness matrices, respectively. Considering axial, lateral, torsional, and coupling effects, these matrices can be decomposed into the corresponding component matrices. The detailed expressions of the submatrices are provided in the Appendix.43\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\mathbf{M}} = \sum\limits_{i = 1}^{4} {{\mathbf{M}}_{{\mathbf{i}}} ,} \, {\mathbf{C}} = \sum\limits_{i = 1}^{6} {{\mathbf{C}}_{{\mathbf{i}}} + \Omega G_{{\mathrm{e}}} ,} \, {\mathbf{K}} = \sum\limits_{i = 1}^{5} {{\mathbf{K}}_{{\mathbf{i}}} } - \Omega^{2} K_{6}$$\end{document}where Ω is the unit spin angular velocity vector, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${K}_{6}$$\end{document} is the rotational softening stiffness matrix related to rotational speed, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${G}_{e}$$\end{document} is Gyroscope matrix44\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$G_{e} = \mathop \smallint \limits_{0}^{le} \rho_{e} J_{p,e} B_{g}^{T} SB_{g} dz,\;\;S = \left[ {\begin{array}{*{20}c} 0 & 1 \\ { - 1} & 0 \\ \end{array} } \right]$$\end{document}where \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\rho}_{e}$$\end{document} is unit material density, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${J}_{p,e}$$\end{document} is the polar moment of inertia, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${B}_{g}$$\end{document} is the strain matrix related to rotational degrees of freedom, S is the antisymmetric fundamental matrix. To solve the resulting nonlinear dynamic equations, the Newmark–β time integration method, which is widely used in structural dynamics, is adopted. In view of the high-frequency vibrations, contact impacts, and strong nonlinearities that may arise during rotary steerable drilling, the average acceleration scheme (β = 0.25, γ = 0.5) is selected to ensure numerical stability and convergence. This method has been demonstrated to be effective for time-domain analysis of multi-degree-of-freedom nonlinear vibration problems. Considering the coexistence of geometric nonlinearity, drill-string–borehole contact nonlinearity, and time-varying loads induced by bit–formation interactions, a predictor–corrector iterative strategy is employed during the time integration process. At each time step, the system response is first predicted based on the previous state. The contact conditions, friction forces, and nonlinear internal forces are then updated to construct the effective stiffness matrix and equivalent load vector until the convergence criterion is satisfied. The convergence criterion is defined in terms of the relative errors of displacement and internal force increments. This strategy enables stable computation while accurately capturing both transient and steady-state vibration responses of the rotary steerable system. Based on the above finite element discretization and numerical solution framework, a three-dimensional nonlinear coupled dynamic solver for the RSS–BHA is developed on the MATLAB platform. The solver is used to generate vibration response data with high temporal resolution, providing reliable physical input for subsequent vibration mode analysis and identification. The overall computational procedure is illustrated in Fig. 5.Fig. 5Flowchart of finite element discretization and numerical solution. Flowchart of finite element discretization and numerical solution. Model validation and case studies To verify the reliability of the proposed model, validation is conducted using a real-world drilling case. In addition, representative vibration modes of engineering significance are identified to systematically evaluate the model’s dynamic response and predictive performance under complex downhole conditions. Model validation A deep well from a Chinese oilfield is selected as a study case to validate engineering applicability of the proposed RSS–BHA coupled vibration model through a comparative analysis between numerical simulations and field measurements. The drilling rig and RSS–BHA configuration are illustrated in Fig. 6a, while the wellbore structure is shown in Fig. 6b. This well adopts a typical deep-well drill-string configuration, in which the RSS–BHA consists primarily of a tricone bit, drill collars, stabilizers, heavy-weight drill pipes, and conventional drill pipes, forming an integrated drilling system extending to the surface. The investigated interval spans a well depth range of 2500–3000 m. The average weight on bit is approximately 180 kN, with a fluctuation amplitude of about 15 kN, and the rotary speed is 60 r/min. All operating parameters are obtained from field measurements and are used as input conditions for numerical simulations to enable a quantitative comparison of RSS–BHA coupled vibration responses.Fig. 6Field case study: (a) Drilling rig and BHA section; (b) Wellbore structure. Field case study: (a) Drilling rig and BHA section; (b) Wellbore structure. Figure 7 compares the numerical simulation results with field measurements of the downhole drill-string rotational speed—represented by the bit rotational speed of the RSS–BHA—and the surface torque as functions of time. The simulation results show good agreement with the field data in terms of overall trends, vibration periods, and peak amplitudes, indicating that the proposed model can reliably capture the global dynamic response of the drill-string under actual drilling conditions. Under the investigated operating conditions, the drill-string exhibits pronounced periodic torsional vibration with a dominant period of approximately 9 s. The slip phase lasts about 5 s, followed by a stick phase of approximately 4 s. During the slip phase, the bit rotational speed increases rapidly from near zero to about 335 r/min and then decays sharply, whereas during the stick phase the bit speed drops to nearly zero. Meanwhile, the surface torque displays strong periodic fluctuations within the range of 14–28 kN m, and its temporal evolution shows a clear correspondence with the time-domain response of the bit rotational speed. These results confirm that the proposed model achieves satisfactory predictive accuracy and good engineering applicability under practical drilling conditions, providing a reliable solid foundation for subsequent vibration-mode analysis and parameter sensitivity investigations.Fig. 7Comparison between numerical simulations and field measurements: (a) Drill-string rotational speed; (b) Surface torque. Comparison between numerical simulations and field measurements: (a) Drill-string rotational speed; (b) Surface torque. In addition to the comparisons of bit rotational speed and surface torque shown in Fig. 7, the three-directional downhole acceleration responses presented in Figs. 8 and 9 also provide supplementary validation evidence for the proposed three-dimensional coupled vibration model. The consistency between simulated and measured X-, Y-, and Z-direction accelerations confirms that the model is capable of reproducing not only the dominant torsional response but also the lateral and axial vibration characteristics under representative stick–slip and whirl conditions.Fig. 8Analysis of stick–slip vibration mode: (a) Time-domain acceleration responses in the X, Y, and Z directions; (b) Three-dimensional time–frequency representation of the Y-direction acceleration.Fig. 9Analysis of whirl vibration mode: (a) Time histories of acceleration in the X, Y, and Z directions; (b) Three-dimensional time–frequency representation of the Y-direction acceleration. Analysis of stick–slip vibration mode: (a) Time-domain acceleration responses in the X, Y, and Z directions; (b) Three-dimensional time–frequency representation of the Y-direction acceleration. Analysis of whirl vibration mode: (a) Time histories of acceleration in the X, Y, and Z directions; (b) Three-dimensional time–frequency representation of the Y-direction acceleration. To quantify the agreement between numerical simulation and field measurement, the Root Mean Squared Error (RMSE), Normalized Root Mean Squared Error (NRMSE), Correlation Coefficient (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\mathrm{R}$$\end{document}), and Relative Error of Dominant Frequency (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\mathrm{E}}_{\mathrm{f}}$$\end{document}) are introduced as:45\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\mathrm{R}\mathrm{M}\mathrm{S}\mathrm{E}=\sqrt{\frac{1}{\mathrm{N}}\sum_{\mathrm{i}=1}^{\mathrm{N}}{\left({\mathrm{y}}_{\mathrm{i}}^{\mathrm{s}\mathrm{i}\mathrm{m}}-{\mathrm{y}}_{\mathrm{i}}^{\mathrm{m}\mathrm{e}\mathrm{a}}\right)}^{2}}$$\end{document}46\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\mathrm{N}\mathrm{R}\mathrm{M}\mathrm{S}\mathrm{E}=\frac{\mathrm{R}\mathrm{M}\mathrm{S}\mathrm{E}}{{\mathrm{y}}_{\mathrm{m}\mathrm{a}\mathrm{x}}^{\mathrm{m}\mathrm{e}\mathrm{a}}-{\mathrm{y}}_{\mathrm{m}\mathrm{i}\mathrm{n}}^{\mathrm{m}\mathrm{e}\mathrm{a}}}\times 100\mathrm{\%}$$\end{document}47\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\mathrm{R}=\frac{\sum_{\mathrm{i}=1}^{\mathrm{N}}\left({\mathrm{y}}_{\mathrm{i}}^{\mathrm{s}\mathrm{i}\mathrm{m}}-{\overline{\mathrm{y}} }^{\mathrm{s}\mathrm{i}\mathrm{m}}\right)\left({\mathrm{y}}_{\mathrm{i}}^{\mathrm{m}\mathrm{e}\mathrm{a}}-{\overline{\mathrm{y}} }^{\mathrm{m}\mathrm{e}\mathrm{a}}\right)}{\sqrt{\left[\sum_{\mathrm{i}=1}^{\mathrm{N}}{\left({\mathrm{y}}_{\mathrm{i}}^{\mathrm{s}\mathrm{i}\mathrm{m}}-{\overline{\mathrm{y}} }^{\mathrm{s}\mathrm{i}\mathrm{m}}\right)}^{2}\right]\left[\sum_{\mathrm{i}=1}^{\mathrm{N}}{\left({\mathrm{y}}_{\mathrm{i}}^{\mathrm{m}\mathrm{e}\mathrm{a}}-{\overline{\mathrm{y}} }^{\mathrm{m}\mathrm{e}\mathrm{a}}\right)}^{2}\right]}}$$\end{document}48\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\mathrm{E}}_{\mathrm{f}}=\frac{\left|{\mathrm{f}}_{\mathrm{d}\mathrm{o}\mathrm{m}}^{\mathrm{s}\mathrm{i}\mathrm{m}}-{\mathrm{f}}_{\mathrm{d}\mathrm{o}\mathrm{m}}^{\mathrm{m}\mathrm{e}\mathrm{a}}\right|}{{\mathrm{f}}_{\mathrm{d}\mathrm{o}\mathrm{m}}^{\mathrm{m}\mathrm{e}\mathrm{a}}}\times 100\mathrm{\%}$$\end{document}where \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\mathrm{N}$$\end{document} is the number of samples, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\mathrm{y}}_{\mathrm{i}}^{\mathrm{s}\mathrm{i}\mathrm{m}}$$\end{document} is the simulated calculation value of the ith sampling point, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\mathrm{y}}_{\mathrm{i}}^{\mathrm{m}\mathrm{e}\mathrm{a}}$$\end{document} is the actual measurement value of the ith sampling point, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\overline{\mathrm{y}} }^{\mathrm{s}\mathrm{i}\mathrm{m}}$$\end{document} is the average value obtained from simulation calculations, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\overline{\mathrm{y}} }^{\mathrm{m}\mathrm{e}\mathrm{a}}$$\end{document} is the actual measured average value, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\mathrm{y}}_{\mathrm{m}\mathrm{a}\mathrm{x}}^{\mathrm{m}\mathrm{e}\mathrm{a}}$$\end{document} is the actual measured maximum value, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\mathrm{y}}_{\mathrm{m}\mathrm{i}\mathrm{n}}^{\mathrm{m}\mathrm{e}\mathrm{a}}$$\end{document} is the actual measured minimum value, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\mathrm{f}}_{\mathrm{d}\mathrm{o}\mathrm{m}}^{\mathrm{s}\mathrm{i}\mathrm{m}}$$\end{document} is the dominant frequency of the simulated signal \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\mathrm{f}}_{\mathrm{d}\mathrm{o}\mathrm{m}}^{\mathrm{m}\mathrm{e}\mathrm{a}}$$\end{document} is the dominant frequency of the actual measured signal. According to Fig. 7, the calculation results showed that the RMSE of the speed signal was 49.76 r/min, the NRMSE was 14.76%, the correlation coefficient R was 0.8956, and the fundamental frequency relative error Ef was 0.001%. The \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\mathrm{R}\mathrm{M}\mathrm{S}\mathrm{E}$$\end{document} of the torque signal was 3.8077 kN/m, the NRMSE was 29.29%, the R was 0.6918 and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${E}_{f}$$\end{document} was 10.00%. This indicates that the model agrees well with the measured results in terms of the time-domain variation trend and frequency-domain dominant characteristics of the speed response and torque response, demonstrating good simulation accuracy and frequency response consistency.The errors primarily stem from uncertainties in the drill bit-rock interaction coefficient, simplifications in the contact between the drill string and the wellbore wall, and noise in field measurements. Analysis of typical vibration modes The developed vibration analysis model for the RSS–BHA has been validated through comparison with field measurements, demonstrating its capability to provide a unified framework for analyzing single vibration modes, pairwise coupled vibrations, and fully coupled vibrations during drilling operations. It should be noted that, under practical drilling conditions, purely single vibration modes and fully coupled vibrations occur relatively infrequently3,8,10. Their dynamic responses are often strongly influenced by operational disturbances, making it difficult for such modes to exhibit stable and engineering-representative characteristics. In contrast, torsion-dominated stick–slip vibration and whirl vibration arising from lateral–torsional coupling are more commonly observed in field operations13,14,35. These vibration modes more effectively reflect the intrinsic multi-degree-of-freedom coupled dynamics of the drill-string and have a direct impact on drilling tool service life. Accordingly, stick–slip vibration and whirl vibration are selected in this study as representative operating conditions for analyzing RSS–BHA vibration characteristics and for further evaluating the applicability of the proposed vibration analysis model under typical engineering vibration scenarios. Characteristics of stick–slip vibration Stick–slip vibration is a nonlinear vibration mode dominated by torsional response and is one of the most frequently observed vibration types in drilling operations47,48. It originates from the periodic accumulation and sudden release of torsional load in the drill-string system and manifests as pronounced localized dynamic responses at the RSS–BHA. Figure 8a presents the time-domain acceleration responses in the X, Y, and Z directions obtained from both field measurements and numerical simulations, while Fig. 8b shows the three-dimensional time–frequency distribution of the Y-direction acceleration. The Y-direction signal is more sensitive to circumferential (tangential) dynamic responses of the tool and is therefore better suited for capturing the periodic excitation characteristics associated with stick–slip vibration; it is thus selected for time–frequency analysis. As shown in Fig. 8a, stick–slip vibration exhibits a distinct periodic pattern, characterized by intermittent accumulation and release of vibration energy. In the lateral directions (X and Y), the acceleration responses display grouped, pulse-like envelopes, with significantly elevated amplitudes during the slip phase and markedly reduced amplitudes during the stick phase. This behavior indicates strong transient dynamic excitation acting on the RSS–BHA during the rapid transition of the bit from a near-stationary state to high rotational speed. The intermittent enhancement of lateral vibrations is closely associated with local imbalance effects induced by the sudden release of torsional load, together with geometric constraints imposed by the borehole. In contrast, the Z-direction acceleration shows a relatively smaller amplitude and smoother temporal variation, indicating that axial vibration is not dominant under the investigated condition and that the system response is primarily governed by torsional dynamics. Further inspection of Fig. 8b shows that the Y-direction acceleration energy is mainly concentrated in the low-frequency range and forms periodically repeating high-energy bands along the time axis. These time–frequency characteristics reflect stable dominant frequency components and pronounced temporal modulation, which are representative features of torsion-dominated stick–slip vibration. Characteristics of whirl vibration Whirl vibration is a nonlinear vibration mode resulting from the coupling between lateral and torsional motions, and its dynamic behavior is more complex than that of stick–slip vibration47,48. Figure 9 presents the time-domain acceleration responses in the X, Y, and Z directions of the RSS–BHA under whirl vibration conditions, together with the three-dimensional time–frequency representation of the Y-direction acceleration. As shown in the time-domain responses (Fig. 9a), whirl vibration exhibits pronounced non-stationary characteristics, with lateral acceleration amplitudes varying continuously over time. This behavior reflects the orbital motion of the drilling tool within the borehole. In the X and Y directions, the acceleration responses are significantly enhanced, and the vibration amplitudes alternate between the two orthogonal directions, indicating strong directional dependence of the lateral motion. This feature is closely associated with eccentric rotation and periodic contact between the drill-string and the borehole, imposed by geometric constraints, highlighting the dominance of lateral dynamic responses9,18. In contrast, the acceleration in the Z acceleration direction exhibits a relatively small amplitude and appears mainly as low-level periodic fluctuations, indicating that axial vibration remains a secondary component under whirl vibration conditions. The overall system dynamic response is therefore governed primarily by the coupled lateral–torsional dynamics. Further inspection of Fig. 9b shows that the vibration energy associated with whirl vibration is more broadly distributed in the frequency domain. In addition to low-frequency components, multiple frequency components coexist during certain time intervals, and the frequency content evolves noticeably with time. These time–frequency characteristics reflect the strong dynamic non-stationarity induced by continuously varying drill-string–borehole contact states and lateral motion trajectories and constitute important identification features of whirl vibration. To evaluate the time-varying spectral consistency between simulation and field measurement, the short-time Fourier transform (STFT) of the acceleration signal a(t) is written as49\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\mathrm{X}\left(\mathrm{t},\mathrm{f}\right)={\int}_{-\infty }^{+\infty }\mathrm{a}\left(\uptau \right){\mathrm{g}}^{*}\left(\uptau -\mathrm{t}\right)\mathrm{e}\mathrm{x}\mathrm{p}\left(-\mathrm{i}2\uppi \mathrm{f}\uptau \right)\mathrm{d}\uptau$$\end{document}and the corresponding spectrogram is defined as50\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\mathrm{P}\left(\mathrm{t},\mathrm{f}\right)={\left|\mathrm{X}\left(\mathrm{t},\mathrm{f}\right)\right|}^{2}$$\end{document} The dominant-frequency ridge is then extracted by51\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\mathrm{f}}_{\mathrm{r}}\left(\mathrm{t}\right)=\mathrm{a}\mathrm{r}\mathrm{g}\mathrm{m}\mathrm{a}\mathrm{x}\left\{\mathrm{P}\left(\mathrm{t},\mathrm{f}\right)\right\}$$\end{document}and the time-averaged relative ridge error between simulation and measurement is defined as52\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\upeta}_{\it{r}}=\frac{1}{{\it{N}}_{\it{t}}}\sum_{\it{k}=1}^{{\it{N}}_{\it{t}}}\frac{\left|{\it{f}}_{\it{r},\it{k}}^{\it{s}\it{i}\it{m}}-{\it{f}}_{\it{r},\it{k}}^{\it{m}\it{e}\it{a}}\right|}{{\it{f}}_{\it{r},\it{k}}^{\it{m}\it{e}\it{a}}}\times 100{\%}$$\end{document} In addition, the energy ratio within a selected frequency band B is introduced as53\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\mathrm{E}}_{\mathrm{B}}=\frac{{\iint}_{\mathrm{B}}\mathrm{P}\left(\mathrm{t},\mathrm{f}\right)\mathrm{d}\mathrm{t}\mathrm{d}\mathrm{f}}{\iint \mathrm{P}\left(\mathrm{t},\mathrm{f}\right)\mathrm{d}\mathrm{t}\mathrm{d}\mathrm{f}}$$\end{document} This metric is used to quantify whether the simulated signal reproduces the measured energy concentration within the physically dominant frequency band. For stick–slip vibrations (see Fig. 8), both the actual measured signal and the numerically simulated signal exhibit a concentrated low-frequency ridge with periodic energy modulation, with a corresponding ridge error of 0.01%. The actual measured and numerically simulated values for the energy ratio in the low-frequency band (0–1 Hz) are 8.47% and 8.44%, respectively. For whirl vibrations (see Fig. 9), both the actual measured signal and the numerically simulated signal exhibit a broader multi-component spectral distribution and stronger temporal variation, with a corresponding ridge error of 6.54%. The actual measured and numerically simulated values for the energy ratio in the low-frequency band (0–1 Hz) are 8.73% and 9.26%, respectively. These quantitative time–frequency metrics further support that the model captures the essential mechanistic differences between stick–slip vibrations, which are primarily torsional, and lateral-torsional whirl vibrations. Sensitivity analysis of typical vibration modes Stick–slip vibration and whirl vibration exhibit pronounced differences in dynamic response characteristics and time–frequency features, reflecting fundamental distinctions in energy distribution patterns and system response mechanisms associated with different vibration modes3,38,47. Owing to the markedly different sensitivities of these vibration modes to operating and structural parameters, targeted parameter sensitivity analyses are required based on the preceding vibration characterization. Such analyses aim to identify the key controlling factors and elucidate their roles under different vibration regimes, thereby providing a reliable basis for drilling parameter optimization and effective vibration control. Sensitivity analysis of stick–slip vibration To systematically evaluate the influence of major operating and structural parameters on the stick–slip vibration characteristics of the RSS–BHA, weight on bit, drill-string rotational speed, well depth, and drill collar length are selected for the sensitivity analysis. Among these, weight on bit and rotational speed are key operating variables that directly govern the bit–formation contact state and the frictional excitation, whereas well depth and drill collar length characterize the scale effects and structural features of the drill-string system12,30,46. A base case is defined as a measured depth of 4000 m, a rotational speed of 100 r/min, a drill-collar length of 200 m, and a weight on bit of 120 kN. The influence of each parameter is investigated by varying one-factor-at-a-time approach, in which a single parameter is varied while the remaining parameters are held constant. The parameter ranges are selected based on typical deep-well drilling conditions to ensure the engineering relevance and practical applicability. The corresponding results are presented in Fig. 10 and Table 1.Fig. 10Sensitivity analysis of stick–slip vibration: (a) Weight on bit; (b) Drill-string rotational speed; (c) Well depth; (d) Drill-collar length.Table 1Results of parameter sensitivity analysis for BHA stick–slip vibration.FactorWeight on bitDrill-string rotation speedWell depthDrill collar lengthParameter608010012014040701001301602000300040005000150250350450550Tss/s7.067.257.087.287.0610.458.337.226.015.098.767.8387.077.457.067.477.087.49Tstick/s2.122.282.242.42.314.693.272.651.571.072.842.52.562.222.62.152.11.651.6Tslip/s4.944.974.844.884.755.765.064.574.444.025.925.335.444.854.854.915.375.435.89f/Hz0.140.140.140.140.140.370.40.420.430.440.110.130.120.140.130.140.130.140.13ωpeak/r min−1171.51190.4189.3208.2207.09109.46173.5237.53280.23365.61198.67206.27218.87216.47228.35216.78210.21203.64197.08ωpeak/ωs1.721.901.892.082.072.742.482.382.342.291.992.062.192.162.282.172.102.041.97Tss, stick–slip period; Tstick, sticking duration; Tslip, slip time; f, dominant vibration frequency; ωpeak, peak rotational speed; ωpeak / ωs, peak-to-set speed ratio; the maximum rotational speed to the nominal value of 100 r min−1. Sensitivity analysis of stick–slip vibration: (a) Weight on bit; (b) Drill-string rotational speed; (c) Well depth; (d) Drill-collar length. Table 1Results of parameter sensitivity analysis for BHA stick–slip vibration.FactorWeight on bitDrill-string rotation speedWell depthDrill collar lengthParameter608010012014040701001301602000300040005000150250350450550Tss/s7.067.257.087.287.0610.458.337.226.015.098.767.8387.077.457.067.477.087.49Tstick/s2.122.282.242.42.314.693.272.651.571.072.842.52.562.222.62.152.11.651.6Tslip/s4.944.974.844.884.755.765.064.574.444.025.925.335.444.854.854.915.375.435.89f/Hz0.140.140.140.140.140.370.40.420.430.440.110.130.120.140.130.140.130.140.13ωpeak/r min−1171.51190.4189.3208.2207.09109.46173.5237.53280.23365.61198.67206.27218.87216.47228.35216.78210.21203.64197.08ωpeak/ωs1.721.901.892.082.072.742.482.382.342.291.992.062.192.162.282.172.102.041.97Tss, stick–slip period; Tstick, sticking duration; Tslip, slip time; f, dominant vibration frequency; ωpeak, peak rotational speed; ωpeak / ωs, peak-to-set speed ratio; the maximum rotational speed to the nominal value of 100 r min−1. Results of parameter sensitivity analysis for BHA stick–slip vibration. Tss, stick–slip period; Tstick, sticking duration; Tslip, slip time; f, dominant vibration frequency; ωpeak, peak rotational speed; ωpeak / ωs, peak-to-set speed ratio; the maximum rotational speed to the nominal value of 100 r min−1. Effect of weight on bit Effect of weight on bit Effect of weight on bit Figure 10a presents the time histories of the bit rotational speed under different weight on bit conditions, and the corresponding stick–slip vibration characteristics are summarized in Table 1. As the weight on bit increases from 60 to 160 kN, the peak bit rotational speed increases markedly from 171.51 to 225.99 r/min, while the stick–slip vibration period increases from 7.06 to 7.24 s. During this process, the stick duration increases monotonically from 2.12 to 2.47 s, whereas the slip duration exhibits minor variation. These results indicate that increasing weight on bit primarily intensifies stick–slip vibration by extending the stick phase and enhancing the transient dynamic response during the subsequent slip phase. T This behavior can be attributed to the increase in frictional torque at the bit–formation interface under higher weight on bit, which drives the system toward a strongly nonlinear, friction-dominated dynamic regime. Although a higher weight on bit is generally beneficial for improving the rate of penetration, it also substantially amplifies the amplitude of stick–slip vibration, thereby increasing the dynamic loading level and potential failure risk of the RSS–BHA. (2)Effect of drill-string rotational speed (2)Effect of drill-string rotational speed Effect of drill-string rotational speed Figure 10b presents the time histories of the bit rotational speed under different drill-string rotational speed conditions, and the corresponding stick–slip vibration characteristics are summarized in Table 1. As the imposed drill-string rotational speed increases from 40 to 160 r/min, the stick–slip vibration period decreases markedly from 10.45 to 5.09 s. During this process, the stick duration is significantly reduced from 4.69 to 1.07 s, whereas the slip duration exhibits only minor variation. These results indicate that increasing drill-string rotational speed effectively suppresses prolonged stick phases and promotes more continuous bit rotation. Meanwhile, the peak bit rotational speed increases from 109.46 to 365.61 r/min; however, the ratio of the peak rotational speed to the imposed drill-string rotational speed decreases gradually from 2.74 to 2.29. This trend indicates that the relative amplification of the system response is reduced at higher drill-string rotational speeds, suggesting improved utilization efficiency of the input rotational energy. Overall, increasing drill-string rotational speed mitigates the instability associated with stick–slip vibration and contributes to improved drilling stability and operational efficiency. (3)Effect of well depth (3)Effect of well depth Effect of well depth Figure 10c presents the time histories of the bit rotational speed under different well depth conditions, and the corresponding stick–slip vibration characteristics are summarized in Table 1. As well depth increases from 2000 to 8000 m, the peak bit rotational speed rises from 198.67 to 239.27 r/min, while the stick–slip vibration period decreases from 8.76 to 6.03 s. During this process, the stick duration is reduced from 2.84 to 1.75 s. In contrast, the variations in slip duration and the dominant vibration frequency remain relatively limited over the considered well depth conditions. These results indicate that increasing well depth affects stick–slip vibration primarily through changes in the overall scale and dynamic characteristics of the RSS–BHA, leading to an amplification of the vibration response. This behavior can be attributed to the increase in the effective length of the RSS–BHA, which reduces the overall torsional stiffness of the system and makes torsional vibration more readily excited. As a result, the bit rotational speed response is enhanced, and the duration of the stick phase is shortened. (4)Effect of drill collar length (4)Effect of drill collar length Effect of drill collar length Figure 10d presents the time histories of the bit rotational speed under different drill-collar length conditions, and the corresponding stick–slip vibration characteristics are summarized in Table 1. As drill-collar length increases from 150 to 450 m, the duration of the stick phase decreases gradually from 2.60 to 1.60 s, whereas the slip duration increases from 4.85 to 5.89 s, indicating a pronounced shortening of the stick phase during the stick–slip vibration process. Meanwhile, the peak bit rotational speed decreases from 228.35 to 197.08 r/min, reflecting a reduction in vibration amplitude with increasing drill-collar length. These results indicate that increasing drill-collar length modifies the structural characteristics of the RSS–BHA and, to some extent, suppresses the intensity of stick–slip vibration. This stabilizing effect is beneficial for improving drill-string operational stability and reducing vibration-induced dynamic loading and failure risk. Sensitivity analysis of whirl vibration Whirl vibration is a typical form of coupled lateral–torsional vibration. Its periodic lateral motion and repeated contact with the borehole wall can induce drill-string fatigue damage and significantly reduce drilling efficiency4,29,37. To identify the dominant factors governing whirl vibration in the RSS–BHA system, drill-collar diameter, well depth, drill-string rotational speed, and weight on bit are selected for sensitivity analysis. Among these factors, the drill-collar diameter primarily controls the lateral stiffness of the drill-string and its contact behavior with the borehole wall. Well depth characterizes the overall scale effect of the drill-string system, whereas rotational speed and weight on bit jointly regulate the excitation intensity and energy input associated with whirl vibration9,11. The parameter ranges are determined based on typical deep-well drilling conditions to ensure the engineering relevance and practical applicability of the analysis. Effect of drill-collar diameter on whirl vibration Effect of drill-collar diameter on whirl vibration Effect of drill-collar diameter on whirl vibration Under backward whirl conditions of the RSS–BHA, the influence of drill-collar outer diameter on the average whirl angular velocity is examined by varying the drill-string rotational speed. As shown in Fig. 11, the average whirl angular velocity increases monotonically with increasing drill-collar diameter at all considered rotational speeds and exhibits a pronounced nonlinear growth trend. When the drill-collar diameter increases from 120.7 to 254 mm, the amplification of whirl angular velocity becomes increasingly significant at higher rotational speeds. For example, at 120 r/min, the whirl angular velocity increases from 8.94 to 66.95 rad/s, corresponding to an increase of more than sevenfold, whereas at 40 r/min it increases only from 2.44 to 15.78 rad/s. This observation indicates that the amplification effect of drill-collar diameter on whirl vibration is strongly dependent on rotational speed. At a given drill-collar diameter, increasing the rotational speed also leads to a marked enhancement of the whirl response, with this effect becoming more pronounced for larger diameters. As the drill-collar diameter increases, the separation between the whirl angular velocity curves at different rotational speeds becomes increasingly evident, revealing a strong coupled amplification effect between rotational speed and drill-collar diameter. From a mechanistic perspective, a larger drill-collar diameter increases the lateral stiffness of the RSS–BHA and strengthens the contact constraint with the borehole wall. Meanwhile, it amplifies unbalanced inertial forces and frictional excitation at the borehole wall, thereby enhancing lateral–torsional coupling and ultimately intensifying whirl vibration.Fig. 11Effect of drill-collar diameter on whirl angular velocity under different rotational speeds. Effect of drill-collar diameter on whirl angular velocity under different rotational speeds. (2)Effect of well depth on whirl vibrational (2)Effect of well depth on whirl vibrational Effect of well depth on whirl vibrational Whirl vibration is a typical form of coupled lateral–torsional vibration and is commonly accompanied by pronounced variations in bending, circumferential, and shear stresses9,11. The axial distribution of stress components along the well depth can be used to characterize the lateral motion of the RSS–BHA and its contact state with the borehole wall, enabling identifying of regions with intensified whirl vibration and elevated structural failure risk37,47. Under operating conditions with a drill-string rotational speed of 80 r/min, a weight on bit of 80 kN, and a total well depth of 7273 m, the distributions of axial, radial, and circumferential stresses, bending, and shear stresses along the RSS–BHA are calculated, as shown in Fig. 12.Fig. 12Distribution of axial, radial, circumferential, bending, and shear stresses along the well depth of the drill-string. The stress state at point P (6829 m) is highlighted. Distribution of axial, radial, circumferential, bending, and shear stresses along the well depth of the drill-string. The stress state at point P (6829 m) is highlighted. Owing to the self-weight of the drill-string, the axial stress generally decreases with increasing well depth. Tensile stress dominates in the upper section of the RSS–BHA, while compressive stress gradually develops toward the bottom-hole region. In the upper sections (0–6829 m), the rotational speed is relatively low, and the bending stress is correspondingly small. In contrast, in the lower sections (6829–7273 m), a pronounced increase in rotational speed leads to a rapid rise in bending stress. Taking point P at a depth of 6829 m as a boundary, multiple stress components exhibit abrupt changes. Both bending and circumferential stress increase markedly at this location, indicating enhanced lateral displacement of the RSS–BHA and intensified contact with the borehole wall. Meanwhile, the shear stress shows localized fluctuations superimposed on an overall decreasing trend, reflecting a strengthening of lateral–torsional coupling. Radial stress increases gradually with depth, further indicating stronger confinement and contact loading in the bottom-hole region. As both bending and circumferential stresses reach relatively high levels at point P, this region can be identified as a potential high-risk zone for intensified whirl vibration and fatigue failure of the drilling assembly. (3)Effects of rotational speed and weight on bit on whirl vibration (3)Effects of rotational speed and weight on bit on whirl vibration Effects of rotational speed and weight on bit on whirl vibration To further examine the effects of rotational speed and weight on bit on whirl behavior of the RSS–BHA, the bending stress at point P is selected as a characteristic parameter. Bending stress is the most sensitive stress component with lateral displacement and borehole wall contact occur in the RSS–BHA, and its magnitude provides a direct indicator of whirl vibration intensity. Therefore, variations in bending stress at point P under different operating conditions are used to evaluate the effects of rotational speed and weight on bit on whirl behavior. Figure 13 shows the variation of bending stress at point P for weights on bit ranging from 60 to 160 kN and rotational speeds from 40 to 150 r/min. As the rotational speed increases from 40 to 90 r/min, the bending stress rises significantly and reaches a maximum near 90 r/min, indicating the most severe whirl vibration under this condition. When the rotational speed further increases from 90 to 120 r/min, the bending stress decreases markedly, suggesting a partial suppression of whirl vibration. With a further increase in rotational speed to 150 r/min, the bending stress rises again, indicating a renewed intensification of whirl behavior. Overall, the response exhibits a pronounced non-monotonic dependence on rotational speed. At a given rotational speed, variations in weight on bit lead to only minor changes in bending stress at point P, and the corresponding curves nearly overlap. This observation indicates that the influence of weight on bit on bending stress and whirl intensity is relatively limited. In contrast, rotational speed exerts a dominant influence on the bending stress at point P and is identified as the primary operational parameter controlling whirl vibration of the RSS–BHA.Fig. 13Variation of bending stress at point P with rotational speed under different weights on bit. Variation of bending stress at point P with rotational speed under different weights on bit. Conclusions A three-dimensional nonlinear coupled vibration model of a static push-the-bit RSS system is established based on finite element dynamics, energy-based methods, and Hamilton’s principle. The model is applied to analyze axial, lateral, and torsional vibrations and their coupled responses of the RSS–BHA under realistic drilling conditions. The main conclusions are summarized as follows:A three-dimensional nonlinear coupled finite element vibration model vibration model is established that enables unified analysis of single vibration modes (axial, torsional, and lateral), pairwise coupled vibrations and fully coupled three-directional vibrations of the RSS–BHA. Field validation demonstrates that the model can accurately reproduce all seven representative vibration types encountered in drilling operations, providing a reliable analytical framework for vibration identification, mechanism analysis, and engineering application in complex drilling conditions.The proposed vibration analysis model successfully reproduces the dynamic characteristics of typical RSS–BHA vibration modes observed in field operations. Torsion-dominated stick–slip vibration and lateral–torsional coupled whirl vibration can be clearly distinguished through their distinct time-domain responses and time–frequency characteristics. Different vibration modes are governed by fundamentally different coupling mechanisms, suggesting that vibration prediction, parameter sensitivity analysis, and mitigation strategies for RSS–BHA systems should be conducted in a mode-specific manner rather than based on a unified vibration assumption.Stick–slip and whirl vibrations of the RSS–BHA exhibit significantly different parameter-dependent behaviors. Stick–slip vibration is primarily controlled by torsional excitation associated to weight on bit, drill-string rotational speed, and torsional stiffness, whereas whirl vibration is dominated by lateral–torsional coupling and is highly sensitive to rotational speed, drill-collar geometry, and well-depth–dependent contact conditions. Consequently, vibration mitigation strategies should be mode-specific, with stick–slip control focusing on the regulation of torsional excitation, while whirl suppression should prioritize the control of rotational speed and lateral structural characteristics. A three-dimensional nonlinear coupled finite element vibration model vibration model is established that enables unified analysis of single vibration modes (axial, torsional, and lateral), pairwise coupled vibrations and fully coupled three-directional vibrations of the RSS–BHA. Field validation demonstrates that the model can accurately reproduce all seven representative vibration types encountered in drilling operations, providing a reliable analytical framework for vibration identification, mechanism analysis, and engineering application in complex drilling conditions. A three-dimensional nonlinear coupled finite element vibration model vibration model is established that enables unified analysis of single vibration modes (axial, torsional, and lateral), pairwise coupled vibrations and fully coupled three-directional vibrations of the RSS–BHA. Field validation demonstrates that the model can accurately reproduce all seven representative vibration types encountered in drilling operations, providing a reliable analytical framework for vibration identification, mechanism analysis, and engineering application in complex drilling conditions. The proposed vibration analysis model successfully reproduces the dynamic characteristics of typical RSS–BHA vibration modes observed in field operations. Torsion-dominated stick–slip vibration and lateral–torsional coupled whirl vibration can be clearly distinguished through their distinct time-domain responses and time–frequency characteristics. Different vibration modes are governed by fundamentally different coupling mechanisms, suggesting that vibration prediction, parameter sensitivity analysis, and mitigation strategies for RSS–BHA systems should be conducted in a mode-specific manner rather than based on a unified vibration assumption. The proposed vibration analysis model successfully reproduces the dynamic characteristics of typical RSS–BHA vibration modes observed in field operations. Torsion-dominated stick–slip vibration and lateral–torsional coupled whirl vibration can be clearly distinguished through their distinct time-domain responses and time–frequency characteristics. Different vibration modes are governed by fundamentally different coupling mechanisms, suggesting that vibration prediction, parameter sensitivity analysis, and mitigation strategies for RSS–BHA systems should be conducted in a mode-specific manner rather than based on a unified vibration assumption. Stick–slip and whirl vibrations of the RSS–BHA exhibit significantly different parameter-dependent behaviors. Stick–slip vibration is primarily controlled by torsional excitation associated to weight on bit, drill-string rotational speed, and torsional stiffness, whereas whirl vibration is dominated by lateral–torsional coupling and is highly sensitive to rotational speed, drill-collar geometry, and well-depth–dependent contact conditions. Consequently, vibration mitigation strategies should be mode-specific, with stick–slip control focusing on the regulation of torsional excitation, while whirl suppression should prioritize the control of rotational speed and lateral structural characteristics. Stick–slip and whirl vibrations of the RSS–BHA exhibit significantly different parameter-dependent behaviors. Stick–slip vibration is primarily controlled by torsional excitation associated to weight on bit, drill-string rotational speed, and torsional stiffness, whereas whirl vibration is dominated by lateral–torsional coupling and is highly sensitive to rotational speed, drill-collar geometry, and well-depth–dependent contact conditions. Consequently, vibration mitigation strategies should be mode-specific, with stick–slip control focusing on the regulation of torsional excitation, while whirl suppression should prioritize the control of rotational speed and lateral structural characteristics.