Unveiling the emission mechanism in analog-doped carbazole-based organic afterglow materials Authors: Zesen Lin, Peng Lan, Zheng Yin, Xiaochun Fan, Jie Kong, Xianhe Zhang, Wei Zhang, Rengo Yoshioka, Xun Tang, Zhu Wu, Youichi Tsuchiya, Ryota Kabe, Meng Zhou, Chihaya Adachi, Bin Liu Published: 2026 ABSTRACT Afterglow from purely organic solids has drawn increasing attention over the past decade. In carbazole-based systems, recent studies revised earlier aggregation-state explanations and implicated trace carbazole analog impurities as the origin. However, the widely assumed charge-trapping mechanism cannot account for exponential decay kinetics, lacks robust experimental validation and leaves some photophysical features unexplained. Here we establish the mechanism by revisiting two representative series of carbazole–analog host–guest systems. Quantitative spectral decomposition and comparative photophysics reveal that the afterglow is dominated by guest phosphorescence, accompanied by an extremely weak power-law long-persistent luminescence. The analog guests are confirmed to act as deep triplet exciton traps and shallow hole traps, the latter of which can enhance hole-transport-type long-persistent luminescence. These insights clarify previously unresolved mechanisms and establish a unified framework for luminescence that integrates energy transfer, exciton diffusion, and three afterglow pathways (delayed fluorescence, room-temperature phosphorescence and long-persistent luminescence), offering design principles for brighter and more persistent purely organic afterglow materials. Introduction In recent years, the afterglow phenomenon of organic solids, encompassing thermally activated delayed fluorescence (TADF)1–3, room-temperature phosphorescence (RTP)4–10, and organic long-persistent luminescence (OLPL)11–18, has opened a new frontier in luminescence research. Conventional wisdom holds that in purely organic solids, long-lived excitons are highly susceptible to various emission quenching processes (collectively referred to as aggregation-caused quenching, ACQ), making afterglow at room temperature nearly unobservable19. Over the past decade, growing reports have described ultralong RTP from purely organic solids20–26, notably in carbazole (Cz) derivatives5,27–30. However, recent work revealed that such RTP often originates from trace Cz analog impurities31–33. Similar impurity-induced afterglow has been confirmed in other organic systems, e.g. derivatives of dibenzofuran, dibenzothiophene, triphenylamine, and boronate esters34–40. These findings prompted a re-examination of the true origin of afterglow in purely organic solids and suggested that analog doping is a general and important mechanism for organic afterglow41–44. Afterglow in doped organic solids (host–guest systems) generally follows two mechanisms (Fig. 1). The first is the emissive triplet-exciton trapping mechanism (triplet confinement), where low-concentration guests with much lower energies of the first triplet (T1) state than those of the hosts (ΔETT ≥ 0.5 eV) confine triplets (Fig. 1a)45,46. This prevents triplet migration to quenching sites and yields exponential decays similar to those of isolated molecules in a rigid matrix. This mechanism underlies RTP and TADF in host–guest systems and is widely exploited in OLEDs (ΔETT > 0.2 eV due to shorter triplet lifetimes)47,48.Fig. 1Schematic illustration of afterglow mechanisms in host-guest organic solids.a Schematic diagram of the triplet exciton trap mechanism involving room-temperature phosphorescence (RTP) and thermally activated delayed fluorescence (TADF). The yellow dashed arrows denote intersystem crossing (ISC) and reverse intersystem crossing (RISC) processes. ΔETT denotes the energy offset between the lowest triplet states of the host and the guest. ΔEST denotes the energy gap between the lowest singlet and the lowest triplet states within the host or the guest molecule itself. b Schematic diagram of the charge carrier trap mechanism in the Type-I organic long-persistent luminescence (OLPL) system. For a Type-II case, see Supplementary Fig. 1. Processes during photo-excitation contain (i) absorption, (ii) inter-CT [(iia) deep hole or (iib) electron trap filling], (iii) CS and opposite-carrier trap filling; The purple arrows denote the electron-transfer processes that occur during photo-excitation. Processes in long-persistent luminescence (LPL): (iv) charge detrapping and recombination, (v) emission; The green arrows denote the electron-transfer processes that occur during LPL. All schematic diagrams take the scenario in which the host molecules are initially excited as an example. FL, Phos., ED, inter-CT and CS represent fluorescence, phosphorescence, exciton diffusion, intermolecular charge transfer and charge separation, respectively. The purple and green arrows denote the electron-transfer processes that occur during photoexcitation and LPL, respectively. Schematic illustration of afterglow mechanisms in host-guest organic solids. a Schematic diagram of the triplet exciton trap mechanism involving room-temperature phosphorescence (RTP) and thermally activated delayed fluorescence (TADF). The yellow dashed arrows denote intersystem crossing (ISC) and reverse intersystem crossing (RISC) processes. ΔETT denotes the energy offset between the lowest triplet states of the host and the guest. ΔEST denotes the energy gap between the lowest singlet and the lowest triplet states within the host or the guest molecule itself. b Schematic diagram of the charge carrier trap mechanism in the Type-I organic long-persistent luminescence (OLPL) system. For a Type-II case, see Supplementary Fig. 1. Processes during photo-excitation contain (i) absorption, (ii) inter-CT [(iia) deep hole or (iib) electron trap filling], (iii) CS and opposite-carrier trap filling; The purple arrows denote the electron-transfer processes that occur during photo-excitation. Processes in long-persistent luminescence (LPL): (iv) charge detrapping and recombination, (v) emission; The green arrows denote the electron-transfer processes that occur during LPL. All schematic diagrams take the scenario in which the host molecules are initially excited as an example. FL, Phos., ED, inter-CT and CS represent fluorescence, phosphorescence, exciton diffusion, intermolecular charge transfer and charge separation, respectively. The purple and green arrows denote the electron-transfer processes that occur during photoexcitation and LPL, respectively. The second is the carrier trapping-detrapping mechanism (Fig. 1b, Supplementary Note 1, and Supplementary Fig. 1): guests act as deep electron or hole traps of hosts when the offset in either the lowest-unoccupied molecular orbital (LUMO) or the highest-occupied molecular orbital (HOMO) (ΔELUMO or ΔEHOMO) is ≥ 0.8 eV11,12,14–16,18,49. Photoexcited excitons may dissociate, forming geminate pairs where one carrier is trapped on the guest and the opposite carrier on other traps in the host, giving long-lived charge-separated states (CSS). Unlike excitons with intrinsic decay pathways, separated charges are not true excited states and can only disappear through recombination; consequently, charge-separated states can persist far longer than excitons. Charge recombination requires thermal detrapping, and the distribution of trap depths leads to power-law decays, analogous to inorganic long-persistent luminescence (LPL)50. Neat organic solids also contain intrinsic traps (tail states, defects), but because most separated charges recombine rapidly, the filling of deep traps is inefficient (Supplementary Note 1, Supplementary Fig. 2), giving only weak LPL and thermally stimulated luminescence51–54. This weak LPL is hard to detect by conventional setups at room temperature (Supplementary Note 1, and Supplementary Fig. 2). In contrast, host–guest systems where the intermolecular charge transfer state (inter-CT) is the lowest excited state (Type-I OLPL) can facilitate efficient charge separation, suppress fast recombination of paired charges, and thus enhance trap filling to yield observable LPL11,15. For Cz-derived host–guest solids, many recent studies have attributed the observed afterglow to long-lived CSS31,33,40,55,56. However, these decays are exponential and spectra dominated by guest phosphorescence, more consistent with confined triplets than CSS (Supplementary Note 1, Supplementary Fig. 3). Certain methodological limitations may also contribute to uncertainty. Some studies compared pristine and doped hosts without contrasting the guest behavior in rigid inert matrices31,34,55, or estimated LUMO levels from HOMO plus optical gaps without accounting for exciton binding energies31,57. The paramagnetic nature of triplet excitons58,59 may complicate interpretation of ESR signals, leaving ESR signals potentially misassigned to radicals42,60. Delayed fluorescence (DF) observed under intense excitation (e.g., 365 nm UV flashlights with power >10 mW cm⁻2) was occasionally attributed to TADF without detailed excitation-power- or temperature-dependent analyses43,55,57. Moreover, most reports treated the host–guest system as a simple two-molecule model, without fully considering exciton diffusion and multi-exciton processes, which may critically influence emission. Consequently, a quantitative, self-consistent model linking triplet confinement, carrier trapping, energy transfer, and multi-exciton dynamics to long-lived luminescence is still lacking. Here we show that the afterglow in Cz-based analog host–guest solids is dominated by guest phosphorescence arising from deep triplet trapping, whereas carrier trapping-detrapping contributes only a minor LPL component. To establish this, we perform quantitative studies on two representative model series: the mCBP-host/analog-guest series (mCBP series), characterized by locally excited (LE) states, and the DPhCzT-host/analog-guest series (DPhCzT series), exhibiting intramolecular charge-transfer (intra-CT) character (Fig. 2a). Accurate HOMO/LUMO levels were measured under identical electrochemical conditions, and fluorescence/phosphorescence were compared with guest-doped polystyrene (PS) references to isolate host–guest-specific effects. Using a lab-built ultrasensitive setup, we observed a weak LPL tail emerging after the exponentially decaying afterglow under weak excitation conditions, confirming the minor role of CSS. Comparison of spectra obtained by transient absorption spectroscopy (TAS) and spectroelectrochemistry, which provides better distinguishability than ESR, verified that the exponential afterglow originates from deep triplet trapping rather than charge trapping-detrapping. Excitation-power- and temperature-dependent measurements clarified DF pathways. Together with quantitative analysis of elementary photophysical processes, energy transfer and exciton diffusion, and afterglow, we establish a self-consistent mechanistic framework for photo-induced emission in Cz derivatives. Finally, we show that, at appropriate concentrations, mCBP isomers acting as shallow hole traps modestly improve the performance of hole-transport-type (p-type) OLPL system based on mCBP host.Fig. 2Molecular structures and orbital energy levels of analog host-guest materials.a The chemical structures and classifications of the molecules as well as the physical form of host-guest mixtures are investigated in this study. LE and intra-CT types refer to materials whose lowest singlet excited state corresponds to a local excited state and an intramolecular charge-transfer state, respectively. b HOMO and LUMO energy levels for compounds in (a) determined by differential pulse voltammetry (DPV) in a nitrogen-filled glovebox (Supplementary Fig. 9). Redox potentials of the compounds in the same series were measured under the same electrolyte conditions. The measurements were conducted in desiccated and oxygen-free dimethylformamide (DMF) or dichloromethane (DCM), employing 0.1 M supporting electrolyte. EOG is the optical gap obtained from spectra (Supplementary Figs. 11–13). Molecular structures and orbital energy levels of analog host-guest materials. a The chemical structures and classifications of the molecules as well as the physical form of host-guest mixtures are investigated in this study. LE and intra-CT types refer to materials whose lowest singlet excited state corresponds to a local excited state and an intramolecular charge-transfer state, respectively. b HOMO and LUMO energy levels for compounds in (a) determined by differential pulse voltammetry (DPV) in a nitrogen-filled glovebox (Supplementary Fig. 9). Redox potentials of the compounds in the same series were measured under the same electrolyte conditions. The measurements were conducted in desiccated and oxygen-free dimethylformamide (DMF) or dichloromethane (DCM), employing 0.1 M supporting electrolyte. EOG is the optical gap obtained from spectra (Supplementary Figs. 11–13). Results Selection and redox properties of Cz-derived host/analog-guest systems To clarify the emission mechanism, we built two representative families of Cz-based host/analog-guest pairs (Fig. 2a, Supplementary Note 2, Supplementary Figs. 4–7; Supplementary Tables 1, 2) that vary in three key dimensions—molecular structure, excited-state character, and solid-state phase. The guests were based on 1H-benzo[f]indole (Bd)31,32, and 5H-benzo[b]carbazole (BCz)33,56,57, both of which were isolated from commercial Cz and could induce afterglow when doped into Cz. The mCBP series represent amorphous LE-type systems, whereas the DPhCzT series comprise crystalline compounds with a pronounced intra-CT character. If similar photophysical behaviors arise in both host–guest and inert-matrix (e.g., PS) systems doped with Bd- and BCz-based guests, the resulting mechanism can be considered more universal rather than a consequence of the unique properties of the host-guest system. This design allows us to assess whether the observed afterglow mechanisms are influenced by molecular packing or phase and clarify the role of the intra-CT character. The mCBP series were prepared as melt-cast amorphous films (Supplementary Note 3.1, Supplementary Fig. 8), whereas the DPhCzT series were obtained as solution-grown crystalline powders. The LUMO and HOMO values were obtained by differential-pulse voltammetry (DPV) conducted in rigorously de-aerated electrolytes (Fig. 2b, Supplementary Note 3.2, Supplementary Figs. 9 and 10). Cz-substituted compounds and their Bd- or BCz-substituted analogs display nearly identical LUMO levels (~ − 2.05 eV for mCBP series compounds, −2.61 eV for DPhCzT series compounds), consistent with the quantum-chemical calculations (Supplementary Fig. 5 in ref. 61. for mCBP; Supplementary Fig. 37 in ref. 31. for DPhCzT). In contrast, parent Cz possesses a shallower LUMO ( − 1.61 eV) than Bd ( − 1.89 eV) and BCz ( − 2.06 eV, Supplementary Fig. 9). Hence, the LUMO energy offset (ΔELUMO) between the Cz-derived host and analog guest is negligible (between −0.08 and 0.03 eV, Supplementary Table 3), indicating that the guest cannot function as an effective electron trap. Measuring all members of each series under identical conditions minimized systematic errors from the singlet exciton binding energy (Eb; Supplementary Table 4). Calculated Eb values reveal that Bd-based compounds possess much smaller Eb (~ 0.00 eV) than their Cz isomers (Cz: 0.24 eV; mCBP: 0.07 eV; DPhCzT: 0.20 eV; Supplementary Figs. 11–13; Supplementary Table 4). In most host–guest pairs, the singlet energy difference, ΔESS, is <0.3 eV (Supplementary Table 3; Supplementary Figs. 14, 15), particularly for systems that use Bd derivatives as the guest. This indicates that the optical gaps between the host and guest are highly similar. Consequently, selective guest excitation is unfeasible at low concentrations. In contrast, the lowest triplet energy offset (ΔETT) always exceeds 0.5 eV, confirming that the guests act as deep triplet-exciton traps. Comparison of the fundamental photophysical properties between the host-guest systems and corresponding guest-doped PS systems To determine whether additional pathways, specifically inter-CT and CS, enhance the RTP of the host–guest systems, we compared their fundamental photophysical properties with those of PS films doped with the same guests (Fig. 3, Supplementary Figs. 16–28; and Supplementary Tables 5–9). In 1 wt%-doped PS films, the guest spectrum is almost identical to that in the dilute toluene solution, indicating that the molecules are essentially dispersed as isolated monomers within the PS matrix (Supplementary Figs. 16 and 17). For the 1 mol% doped mCBP series, both fluorescence and phosphorescence originate almost exclusively from the guest, even under host-selective excitation ( ≤ 340 nm), and the spectra are virtually indistinguishable from those of the corresponding PS films (Fig. 3a, Supplementary Figs. 16a–f and 18). In contrast, the 1 mol% doped DPhCzT series show pronounced host–guest emission mixing: prompt fluorescence originates from both the host aggregate state and the guest molecule, while the phosphorescence spectrum matches that of the guest-doped PS film, indicating that RTP originates exclusively from the guest (Fig. 3b, Supplementary Figs. 16g–i, 19 and 20). Notably, mCBP exhibits a red-shifted RTP spectrum (ET1 = 2.86 eV) from the biphenyl moiety62 relative to its 77 K phosphorescence (3.08 eV) mainly from the Cz moiety (Supplementary Note 3.3, Supplementary Fig. 21).Fig. 3Comparison of fluorescence and phosphorescence properties between analog-doped systems and corresponding polystyrene (PS) doped films.a Steady-state photoluminescence (PL), fluorescence (FL), and phosphorescence spectra of mCzBdBP-doped mCBP film (1 mol%), mCzBdBP-doped PS film (1 wt%) and neat films of mCBP and mCzBdBP. The time range represents the integration window of the time-resolved emission spectra. b PL, FL and delayed emission spectra of DPhBdT-doped DPhCzT crystal powder (1 mol%), PS films (1 wt%) and undoped crystal powder of DPhCzT and DPhBdT. c, d FL (c) and room-temperature phosphorescence (RTP) (d) decay profiles of mCzBdBP-doped mCBP film and PS films doped with mCBP and mCzBdBP. e, f FL (e) and phosphorescence (f) decay profiles of DPhBdT-doped DPhCzT film and PS films doped with DPhCzT and DPhBdT. g, h Quantum yields of PL (g) and RTP (h) for analog-doped systems and corresponding PS-doped systems. All samples were encapsulated under a nitrogen atmosphere. Doping concentrations: analog-doped systems at 1 mol%; PS systems at 1 wt% except for DPhBCzT/PS (0.2 wt%). All measurements were conducted at room temperature unless otherwise specified. Source data are available in the Figshare repository. Comparison of fluorescence and phosphorescence properties between analog-doped systems and corresponding polystyrene (PS) doped films. a Steady-state photoluminescence (PL), fluorescence (FL), and phosphorescence spectra of mCzBdBP-doped mCBP film (1 mol%), mCzBdBP-doped PS film (1 wt%) and neat films of mCBP and mCzBdBP. The time range represents the integration window of the time-resolved emission spectra. b PL, FL and delayed emission spectra of DPhBdT-doped DPhCzT crystal powder (1 mol%), PS films (1 wt%) and undoped crystal powder of DPhCzT and DPhBdT. c, d FL (c) and room-temperature phosphorescence (RTP) (d) decay profiles of mCzBdBP-doped mCBP film and PS films doped with mCBP and mCzBdBP. e, f FL (e) and phosphorescence (f) decay profiles of DPhBdT-doped DPhCzT film and PS films doped with DPhCzT and DPhBdT. g, h Quantum yields of PL (g) and RTP (h) for analog-doped systems and corresponding PS-doped systems. All samples were encapsulated under a nitrogen atmosphere. Doping concentrations: analog-doped systems at 1 mol%; PS systems at 1 wt% except for DPhBCzT/PS (0.2 wt%). All measurements were conducted at room temperature unless otherwise specified. Source data are available in the Figshare repository. Fluorescence and phosphorescence lifetimes of all guests are comparable in the corresponding host and PS (Fig. 3c–f, Supplementary Note 3.4, Supplementary Figs. 16 and 22–26, Supplementary Table 5). In the Cz-based host, the guest fluorescence lifetime \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$({\tau }_{{{\rm{F}}}})$$\end{document}(τF) is slightly longer and the phosphorescence lifetime \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\tau }_{{{\rm{P}}}}$$\end{document}τP is slightly shorter than those in PS (e.g., for DPhBdT, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\tau }_{{{\rm{F}}}}$$\end{document}τF = 15.8 ns, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\tau }_{{{\rm{P}}}}$$\end{document}τP = 0.82 s in PS; \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\tau }_{{{\rm{F}}}}$$\end{document}τF = 16.2 ns, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\tau }_{{{\rm{P}}}}$$\end{document}τP = 0.65 s in DPhCzT). All guests retain long RTP lifetimes (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\tau }_{{{\rm{P}}}}$$\end{document}τP: 500 ~ 800 ms) in both environments (Fig. 3d, f and Supplementary Fig. 16c, f, i; Supplementary Table 5). These observations confirm that the host largely preserves the intrinsic singlet and triplet emission kinetics of the guests. In the DPhCzT series, the mixed nature of the prompt fluorescence is further corroborated by the time-gated spectra (Fig. 3e, Supplementary Figs. 19 and 20): the delayed trace shows a clear inflection at 5–10 ns, the pre-bend portion matching DPhCzT emission and the post-bend portion matching that of DPhBdT or DPhBCzT, because the \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\tau }_{{{\rm{F}}}}$$\end{document}τF of DPhCzT (1.85 ns) is much shorter than those of the guests (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\tau }_{{{\rm{F}}}}$$\end{document}τF: 20.3 ns for DPhBCzT). By contrast, in the mCBP series where the host lifetime exceeds that of the guests, no such kink is observed; the host–guest solid exhibits a single-exponential decay whose \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\tau }_{{{\rm{F}}}}$$\end{document}τF falls between the host and guest values and is closer to those of the guests. Collectively, lifetimes corroborate the spectral assignments, showing a negligible host effect on guest triplet decay. The overall photoluminescence quantum yields remain modest (ΦPL < 35 %) and the phosphorescence quantum yields are very low (ΦPhos < 2 %) across all samples (Fig. 3g, h; Supplementary Note 3.5, Supplementary Tables 6–9). ΦPhos was estimated based on the spectral contribution of the phosphorescence component in the total photoluminescence (see Section 4.4, Supplementary Figs. 27–29, Supplementary Tables 6–9). In PS, DPhCzT analogs (DPhBdT and DPhBCzT) exhibit lower ΦPL ( < 10%) but higher ΦPhos (≈ 1.6%) than the LE-type mCBP analogs (mCzBdBP, mBBP, and mBCzBP) (ΦPL > 17%, ΦPhos < 0.6% for mCBP analogs; Supplementary Tables 6). This is consistent with the intersystem crossing (ISC) efficiencies of DPhCzT analogs possessing an intra-CT state being 3–4 times higher than those of the LE-type mCBP analogs (e.g., ΦISC: 2.2% for DPhBdT, 0.6% for mCzBdBP, Supplementary Table 8). However, in host–guest solids, ΦPhos values decreases by a factor of 1–6 compared with the PS films (Fig. 3g, h; Supplementary Table 10), indicating the presence of extra excited-state quenching pathways (kq). For instance, although DPhCzT as a host exhibits highly efficient ISC (kISC = 8.2 × 107 s-1; Supplementary Note 3.6, Supplementary Table 7; Supplementary Fig. 30a, b), the ΦPhos of DPhBdT and DPhBCzT in DPhCzT falls to just 20–30 % of that of the PS reference (Fig. 3h; and Supplementary Table 10). Thus, the hosts do not enhance ΦPhos of the guests relative to inert rigid matrices. Overall, the host–guest systems (Supplementary Table 3) do not significantly improve guest RTP, and possible host aggregation (e.g., H-aggregates5) also shows no detectable contribution to RTP, such as prolongation of the lifetime or improvement in the quantum yield. However, the crystalline host–guest systems (DPhCzT series) retained visible RTP after prolonged air exposure, in contrast to the rapid quenching observed in the PS films (Supplementary Note 3.7, Supplementary Figs. 31, 32), largely due to the suppression of oxygen diffusion within the crystals. High-sensitivity afterglow measurements and time-resolved absorption/emission spectroscopy We first probed the afterglow of neat hosts (mCBP, DPhCzT) and host–guest solids (mCzBdBP/mCBP, mBCzBP/mCBP, DPhBdT/DPhCzT, DPhBCzT/DPhCzT) under single-photon excitation with our home-built, high-sensitivity setup (Fig. 4a,b, Supplementary Note 3.8, and Supplementary Figs. 33–36). The noise level was approximately 30 fW cm–2; consequently, any optical signal exceeding this threshold could be reliably detected. All neat hosts and host–guest systems exhibited weak LPL (Fig. 4a, b and Supplementary Fig. 37). The LPL emission in host-guest systems emerged after a strong RTP that lasted for approximately 10 seconds. Because the excitation intensity was kept low (100 µW cm⁻²), the observed LPL occurred entirely under single-photon conditions. In contrast, the doped PS films show RTP only, with no detectable LPL. The appearance of weak LPL confirms the creation of CSS in host-guest systems under photoexcitation, but their population is extremely small, 3–4 orders of magnitude less than that of triplet excitons (Fig. 4a, b).Fig. 4Afterglow behaviors, time-resolved absorption and emission spectra of host-guest systems.a, b Afterglow decay profiles of guest-doped host system, neat host and guest-doped polystyrene (PS) film under low-power excitation (340 nm, 100 µW/cm2, 1 min): (a) mCBP as the host and its analogs as the guest; (b) DPhCzT as the host and its analogs as the guest. Guest concentration: 1 mol% in host, 1 wt% in PS. The inset shows the corresponding photoluminescence intensities. IRF&BES denote the setup instrument response function and background emission signal (Supplementary Fig. 33c, d). The afterglow signal (0.2-10 s) of IRF&BES likely arises from weak luminescence of the light-absorbing coating inside the chamber, rather than the light source. The red dashed line indicates the noise level. c Afterglow decay profiles of host-guest films with different doping concentrations, neat host films, and neat guest powders, displayed with dual scales of intensity (left axis) and equivalent irradiance (right axis). Excitation: 340 nm, 100 µW/cm2, 1 min. The decay curve overlaps with the IRF&BES, confirming that the material exhibits no detectable emission. d, e Comparison between the millisecond-range and the nanosecond-range transient absorption spectra (TAS), as well as the spectroelectrochemically obtained radical ion absorption spectra of mCzBdBP/mCBP (d) and DPhBdT/DPhCzT (e). f Emission decay profile of DPhBdT/DPhCzT with different doping concentrations, 1 wt% DPhCzT/PS and DPhBdT/PS. The intensities are normalized to the intensity at time zero. Laser power: 0.5 mW (1 wt% DPhCzT/PS), 1 mW (1 wt% DPhBdT/PS, 0-100 ns and 1-100 ms), 4 mW (1 wt% DPhBdT/PS, 1-1000 μs), and 4.4 mW (DPhBdT/DPhCzT). FL,H and FL,G represent fluorescence of host and guest, respectively; DF denotes delayed fluorescence. g Transient emission spectra of 1 mol% DPhBdT/DPhCzT (0-100 ns, 0.3-100 μs, 0.1-100 ms), derived from the same dataset as in (f). Other abbreviations are as defined in Figs. 1 and 3. Source data are available in the Figshare repository. Afterglow behaviors, time-resolved absorption and emission spectra of host-guest systems. a, b Afterglow decay profiles of guest-doped host system, neat host and guest-doped polystyrene (PS) film under low-power excitation (340 nm, 100 µW/cm2, 1 min): (a) mCBP as the host and its analogs as the guest; (b) DPhCzT as the host and its analogs as the guest. Guest concentration: 1 mol% in host, 1 wt% in PS. The inset shows the corresponding photoluminescence intensities. IRF&BES denote the setup instrument response function and background emission signal (Supplementary Fig. 33c, d). The afterglow signal (0.2-10 s) of IRF&BES likely arises from weak luminescence of the light-absorbing coating inside the chamber, rather than the light source. The red dashed line indicates the noise level. c Afterglow decay profiles of host-guest films with different doping concentrations, neat host films, and neat guest powders, displayed with dual scales of intensity (left axis) and equivalent irradiance (right axis). Excitation: 340 nm, 100 µW/cm2, 1 min. The decay curve overlaps with the IRF&BES, confirming that the material exhibits no detectable emission. d, e Comparison between the millisecond-range and the nanosecond-range transient absorption spectra (TAS), as well as the spectroelectrochemically obtained radical ion absorption spectra of mCzBdBP/mCBP (d) and DPhBdT/DPhCzT (e). f Emission decay profile of DPhBdT/DPhCzT with different doping concentrations, 1 wt% DPhCzT/PS and DPhBdT/PS. The intensities are normalized to the intensity at time zero. Laser power: 0.5 mW (1 wt% DPhCzT/PS), 1 mW (1 wt% DPhBdT/PS, 0-100 ns and 1-100 ms), 4 mW (1 wt% DPhBdT/PS, 1-1000 μs), and 4.4 mW (DPhBdT/DPhCzT). FL,H and FL,G represent fluorescence of host and guest, respectively; DF denotes delayed fluorescence. g Transient emission spectra of 1 mol% DPhBdT/DPhCzT (0-100 ns, 0.3-100 μs, 0.1-100 ms), derived from the same dataset as in (f). Other abbreviations are as defined in Figs. 1 and 3. Source data are available in the Figshare repository. All guests have shallower HOMO levels than their hosts, suggesting hole-trapping ability. However, the LPL intensities of doped systems remain comparable to those of the neat hosts and show no significant dependence on the doping concentration (Fig. 4c). Therefore, the observed LPL is mainly attributed to charge separation within the host aggregate itself, with minor guest contribution, when the excitation wavelength falls within the absorption range of the hosts (Supplementary Fig. 38a, b). The weak guest contribution to LPL stems from two main factors. First, classical OLPL requires large host–guest offsets (ΔEHOMO or ΔELUMO ≥ 0.8 eV) to immobilize one type of charge carrier11,14–16,18. However, here ΔEHOMO and ΔELUMO are below 0.5 eV (Supplementary Table 3), so trapped carriers readily escape and recombine at room temperature, which reduces the population of long-lived, charge-separated states. Second, all systems exhibit pronounced guest phosphorescence, with a large singlet–triplet energy gap of the guest (ΔEST,guest > 0.5 eV, Supplementary Table 4, Supplementary Fig. 17), indicating that fewer excitons dissociate to populate host traps compared with classical inter-CT or TADF systems, thereby limiting LPL generation12,63. To pinpoint the true metastable species influencing the millisecond-to-second exponential afterglow, we compared the millisecond-scale excited-state absorption (ESA) spectra of the analog-doped solids with (i) the radical-ion spectra of hosts and guests obtained electrochemically and (ii) triplet absorption features captured by nanosecond TAS (ns-TAS; Fig. 4d, e; and Supplementary Figs. 39–47). No characteristic radical-ion peaks are detected in the ms-TAS spectra of any of the host–guest systems (e.g., 1.4 eV peak for mCzBdBP•+, 1.7 eV peak for DPhBdT•+, 1.8 eV peak for DPhCzT•−; Fig. 4c, d, and Supplementary Figs. 40–47). The absence of CSS signals likely stems from their extremely low population, rendering them undetectable by TAS. Instead, the ms-TAS spectra of all host–guest systems closely match those of the corresponding guest-doped PS films, with the ESA bands aligning with the guest triplet signatures observed on the nanosecond timescale (Fig. 4d, e and Supplementary Fig. 39). Additionally, the lifetimes of the ms-ESA match the phosphorescence lifetimes (Supplementary Note 3.9, Supplementary Figs. 40–47). These observations collectively demonstrate that the guest-molecule triplet state is responsible for the exponential afterglow, rather than the CSS. The presence of inter-CT states can enhance ISC without compromising the radiative rate of localized triplet states63. Therefore, we assessed whether pronounced inter-CT populations exist in our host–guest solids by combining time-resolved emission spectra (TRES; Fig. 4f, g, and Supplementary Figs. 18–20) with femtosecond TAS (fs-TAS; Fig. 5 and Supplementary Figs. 48, 49). For the DPhCzT-based host–guest series (Fig. 4f, g), TRES cleanly resolves aggregated host fluorescence, guest prompt fluorescence, guest DF, and guest RTP, but shows no discernible inter-CT emission. The mCBP series behave similarly, displaying only guest-origin emission with no discernible inter-CT signature (Supplementary Fig. 18).Fig. 5Direct evidence for fluorescence resonance energy transfer (FRET) in the mBBP/mCBP system: femtosecond transient absorption (fs-TA) results of the mBBP/mCBP system under a nitrogen atmosphere.a–d fs-TA maps of (a) mCBP neat film, (b) 1 mol% mBBP/mCBP, (c) 20 mol% mBBP/mCBP, and (d) 1 wt% mBBP/PS films. e–h fs-TA spectra of (e) mCBP neat film, f 1 mol% mBBP/mCBP, g 20 mol% mBBP/mCBP, and (h) 1 wt% mBBP/PS films, at different delay times. i–l TA kinetic traces (probed at 490 and 630 nm) of (i) mCBP neat film, j 1 mol% mBBP/mCBP, (k) 20 mol% mBBP/mCBP, and (l) 1 wt% mBBP/PS films. Excitation condition: 330 nm, 100 μW. ESA(S1, neat mCBP), ESA(S1, mBBP) and ESA(\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${{{\rm{S}}}}_{1}^{*}$$\end{document}S1*, mBBP) denote excited-state absorption (ESA) originating from the lowest singlet excited state (S1) of mCBP in neat film, and from the S1 and hot S1 (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${{{\rm{S}}}}_{1}^{*}$$\end{document}S1*) states of mBBP in low-concentration PS films, respectively. Source data are available in the Figshare repository. Direct evidence for fluorescence resonance energy transfer (FRET) in the mBBP/mCBP system: femtosecond transient absorption (fs-TA) results of the mBBP/mCBP system under a nitrogen atmosphere. a–d fs-TA maps of (a) mCBP neat film, (b) 1 mol% mBBP/mCBP, (c) 20 mol% mBBP/mCBP, and (d) 1 wt% mBBP/PS films. e–h fs-TA spectra of (e) mCBP neat film, f 1 mol% mBBP/mCBP, g 20 mol% mBBP/mCBP, and (h) 1 wt% mBBP/PS films, at different delay times. i–l TA kinetic traces (probed at 490 and 630 nm) of (i) mCBP neat film, j 1 mol% mBBP/mCBP, (k) 20 mol% mBBP/mCBP, and (l) 1 wt% mBBP/PS films. Excitation condition: 330 nm, 100 μW. ESA(S1, neat mCBP), ESA(S1, mBBP) and ESA(\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${{{\rm{S}}}}_{1}^{*}$$\end{document}S1*, mBBP) denote excited-state absorption (ESA) originating from the lowest singlet excited state (S1) of mCBP in neat film, and from the S1 and hot S1 (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${{{\rm{S}}}}_{1}^{*}$$\end{document}S1*) states of mBBP in low-concentration PS films, respectively. Source data are available in the Figshare repository. Fs-TAS control experiments comparing the neat host, host-guest blends (1 mol% and 20 mol%), and guest-doped PS references (1 wt%) reveal no signals attributable to inter-CT species. Instead, the results provide clear evidence of host-to-guest energy transfer (Fig. 5; and Supplementary Figs. 48, 50, 51). Taking the mBBP/mCBP system as an example, the 20 mol% system exhibits an excited state absorption (ESA) band near 500 nm, attributed to the guest’s lowest singlet excited state (S1). This signal rises within 0.1–3 ps concomitantly with the decay of the host ESA, whereas a similar spectral feature in the 1 mol% mBBP/mCBP sample emerges only after ~100 ps. To disentangle these coupling signals, singular-value decomposition (SVD) followed by multivariate curve resolution alternating least squares (MCR-ALS) analysis64 was performed, revealing only two clear signal components (Supplementary Fig. 50). The associated spectra indicate that the first component is characteristic of the host S1 absorption, whereas the second is consistent with the guest S1 absorption (Supplementary Figs. 50b, c). Notably, the concentration profiles show that the decay of the host component over the 1–100 ps time window is accompanied by a concomitant rise of the guest component, a kinetic signature characteristic of energy transfer (Supplementary Figs. 50d, e). Moreover, as inter-CT states are typically associated with radical-ion absorption features, the absence of such signatures in the fs-TAS data further excludes the involvement of inter-CT processes in the present system (Supplementary Fig. 51). These observations indicate that the contribution of inter-CT processes is negligible, which is consistent with the ΔEG–interCT values summarized in Supplementary Table 3. When ΔEG–interCT is a negative value (<−0.1 eV; e.g., mBCzBP/mCBP and DPhBCzT/DPhCzT), the lowest singlet excited state (S1) of the system is localized on the guest molecule, and no inter-CT processes are detectable. When ΔEG–interCT is nearly zero (e.g. mCzBdBP/mCBP, DPhBdT/DPhCzT), a rapid equilibrium is established between the guest S1 (S1,G) and inter-CT states. Given that emission from inter-CT states is typically slower than that from locally excited singlet states, the inter-CT excitons preferentially relax to the S1,G state. Consequently, the population of inter-CT states remains extremely low and thus spectroscopically unresolvable under our experimental conditions. Analysis of delayed fluorescence in the Cz-derived host/analog-guest systems In current studies of organic solid-state RTP materials, researchers often use high-power 365 nm UV flashlights ( > 10 mW cm⁻2) to preliminarily screen for visible RTP emission, with the corresponding afterglow spectra recorded by CCD. As a result, in addition to RTP, a long-lived DF signal is often observed. This DF is typically attributed to a triplet–triplet annihilation (TTA) process. In our mCBP host–guest systems, where large ΔEST ( > 0.6 eV) excludes TADF, the DF indeed follows TTA characteristics: bimolecular kinetics with superlinear excitation intensity dependence at low excitation power (ideal slope = 2 in a log–log plot; Fig. 6a, b, and Supplementary Note 3.10, Supplementary Figs. 52, 53). However, due to additional quenching processes in organic solids, such as singlet–singlet annihilation (SSA) or triplet–polaron annihilation (TPA), the slope in the log–log plot often deviates from 2, resulting in an observed slope of ~1.5 (Fig. 6b)65,66. Since RTP is a single-photon process, the relative contributions of RTP and TTA-DF to the afterglow spectrum at a fixed time delay depend on excitation intensity: RTP dominates at low power, whereas the rapidly rising TTA-DF prevails at higher power (Fig. 6a and Supplementary Fig. 52a, b). Under identical excitation conditions, higher guest concentrations further increase the TTA-DF fraction in the afterglow (Supplementary Fig. 54).Fig. 6Delayed fluorescence (DF) in analog host-guest systems.a, c Afterglow 3D maps of (a) mCzBdBP/mCBP and (c) DPhBdT/DPhCzT with 1 mol% guest concentration under high-power UV excitation. Excitation conditions: 365 nm, 56 mW/cm2 (mCzBdBP/mCBP) and 50 mW/cm2 (DPhBdT/DPhCzT). b, d Dependence of the afterglow emission intensity (375–500 nm at 100 ms) on the power density of the incident light for (b) 1 mol% mCzBdBP/mCBP amorphous film and (d) DPhBdT/DPhCzT crystal powder. Excitation conditions: 340 nm or 365 nm for 10 s (mCzBdBP/mCBP) and 365 nm for 10 s (DPhBdT/DPhCzT). Raw data are provided in Supplementary Fig. 53b–d. e Comparison of time-resolved emission spectra of 10 mol% DPhBdT/DPhCzT crystal powder measured at room temperature and at 10 K. TTA-DF and PRET-DF denote delayed fluorescence from triplet–triplet annihilation and phosphorescence resonance energy transfer from T1,H to S1,G, respectively. Phos. is the abbreviation of phosphorescence. CW-Excitation denotes continuous-wave excitation. Source data are available in the Figshare repository. Delayed fluorescence (DF) in analog host-guest systems. a, c Afterglow 3D maps of (a) mCzBdBP/mCBP and (c) DPhBdT/DPhCzT with 1 mol% guest concentration under high-power UV excitation. Excitation conditions: 365 nm, 56 mW/cm2 (mCzBdBP/mCBP) and 50 mW/cm2 (DPhBdT/DPhCzT). b, d Dependence of the afterglow emission intensity (375–500 nm at 100 ms) on the power density of the incident light for (b) 1 mol% mCzBdBP/mCBP amorphous film and (d) DPhBdT/DPhCzT crystal powder. Excitation conditions: 340 nm or 365 nm for 10 s (mCzBdBP/mCBP) and 365 nm for 10 s (DPhBdT/DPhCzT). Raw data are provided in Supplementary Fig. 53b–d. e Comparison of time-resolved emission spectra of 10 mol% DPhBdT/DPhCzT crystal powder measured at room temperature and at 10 K. TTA-DF and PRET-DF denote delayed fluorescence from triplet–triplet annihilation and phosphorescence resonance energy transfer from T1,H to S1,G, respectively. Phos. is the abbreviation of phosphorescence. CW-Excitation denotes continuous-wave excitation. Source data are available in the Figshare repository. In contrast, the DF observed in the DPhCzT series is neither TTA-DF nor TADF, because it shows a single-photon characteristic (Fig. 6c, d and Supplementary Fig. 52c, d), shows no thermal activation behavior (Fig. 6e), and is guest concentration-independent (Supplementary Fig. 55). This DF is also not the recombination fluorescence (RF) of photoinduced geminate pairs67, as no distinct CSS was observed in the prior ps–ns TAS spectra. In organic solids, RF is essentially equivalent to LPL: both involve charge separation and typically show power-law decay67, because the distribution of HOMO, LUMO, and trap levels is broad rather than discrete in disordered materials52, unlike ideal single crystals at low temperature. The distinction is mainly semantic: LPL usually refers to afterglow lasting beyond a second, whereas RF denotes DF in the μs–ms range. However, the DF of the DPhCzT series follows a power law only up to ~0.1 s before switching to exponential decay (Figs. 4f and 6c), indicating that this DF does not originate from charge separation. With these possibilities excluded, we attribute the DF of the DPhCzT series to a phosphorescence resonance energy transfer (PRET) process from the host T1 state to the guest S1 state (Supplementary Fig. 56a) for the reasons outlined below68–71. (i) The DPhCzT series possess efficient PRET (e.g., efficiency ΦPRET = 55.4%, rate constant kPRET = 0.24 s-1 for 1 mol% DPhBdT/DPhCzT, Supplementary Tables 11, 12), with the Förster integral for PRET (JPRET) about one order of magnitude smaller than the corresponding integrals of fluorescence resonance energy transfer (FRET; JFRET), in contrast to the mCBP-based systems where JPRET is three orders of magnitude smaller than JFRET (Supplementary Fig. 56b; and Supplementary Table 11). (ii) The DF follows a power law in the μs–ms range but becomes exponential beyond ~0.1 s. This can be readily explained by the dependence of kPRET on the concentration of triplet excitons on the host, which influences the distance between the excited host and guest molecules, r. Immediately after excitation, r follows a normal distribution, so PRET-DF initially exhibits power-law behavior. Hosts with smaller r values have larger kPRET, leading to preferential triplet transfer to the guest. As host triplets decay, the remaining triplets are farther from the guest with a narrower r distribution, yielding exponential decay characteristics for DF on longer timescales. (iii) Because both PRET and FRET originate from the same pool of excited host molecules, their initial energy donor–acceptor distance (r) distributions are identical. Therefore, the ratio of their rate constants calculated from the average distance (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left\langle r\right\rangle$$\end{document}r), kFRET / kPRET, remains constant (e.g., 5.8 × 109 for the DPhBdT/DPhCzT pair) and is independent of guest concentration (Supplementary Table 12), explaining the concentration-independent DF-to-RTP intensity ratio in the DPhCzT series. Analysis of energy transfer processes The steady-state photoluminescence spectra evolve systematically with increasing analog guest concentration: the host fluorescence diminishes, while the guest fluorescence (including DF) and guest phosphorescence increase correspondingly (Fig. 7a,b, Supplementary Figs. 28 and 29). This reciprocal spectral evolution is consistent with efficient host-to-guest energy transfer (Supplementary Fig. 56e). Quantitative distance analysis shows that at 1 wt% guest doping, the calculated average donor-acceptor distance \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left\langle r\right\rangle$$\end{document}r (mCzBdBP/mCBP: 1.02 nm; DPhBdT/DPhCzT: 0.71 nm. Supplementary Table 12) remains smaller than the Förster radius (R0. mCzBdBP/mCBP: 1.73 nm, DPhBdT/DPhCzT: 0.87 nm. Supplementary Table 11). Therefore, a significant fraction of photoexcited host molecules statistically fall within the regime r < R0, supporting near-field Förster resonance energy transfer ( < 10 nm) as the dominant pathway, although far-field radiative energy transfer ( > 10 nm) remains a possibility52. In mCBP series, host fluorescence nearly vanishes at 1 mol% guest, whereas in DPhCzT series significant host emission remains. At the 10 mol% guest-doping level, the increased guest self-absorption suppresses the higher-energy shoulder peak in the photoluminescence spectra. According to the TRES results, the photoluminescence spectra at different doping levels can be well reproduced by a linear combination of host fluorescence, guest fluorescence, and guest phosphorescence (Fig. 7c, Supplementary Note 3.11, Supplementary Figs. 28, 29 and 56c, d; see Section 4.4 for the method). As typical heavy-atom-free materials, both hosts and guests exhibit low ISC efficiencies (e.g., 10.8% for mCBP and 15.1% for DPhCzT, Supplementary Table 7), indicating that singlet excitons dominate under steady-state conditions. Consequently, FRET is expected to be the primary energy transfer mechanism, while Dexter energy transfer is expected to be rare at low doping67. If PRET from the host T1 state occurs, it would further suppress Dexter energy transfer owing to competition. Therefore, host-to-guest energy transfer is a non-negligible photophysical process for modulating the spectral composition and guest ΦPhos.Fig. 7Quantitative analysis of FRET in analog host-guest systems.a, b Guest concentration dependence of the PL spectra in host–guest systems of mCBP series (a) and DPhCzT series (b). c PL spectral linear-combination fitting results for isomer-doped DPhCzT powder with 0.1 mol% guest concentration. Host FLagg denotes the fluorescence spectra of host aggregates. Methods and detailed data are provided in Section 4.4 and Supplementary Table 9. d, e The spectral overlap between host fluorescence and guest absorption of mCBP (d) and DPhCzT (e) series systems. f FRET efficiency (ΦFRET (S1,H → S1,G)) of all host-guest materials with 1 mol% guest concentration. g Dependence of ΦFRET (S1,H → S1,G) on guest concentration for mCzBdBP/mCBP, DPhBdT/DPhCzT and co-doped polystyrene films of mCzBdBP and mCBP [(mCzBdBP+mCBP)/PS]. For the (mCzBdBP + mCBP)/PS films, the total nominal doping concentration was fixed at 1 wt%. For comparison with the mCzBdBP/mCBP system, the guest concentration in the (mCzBdBP + mCBP)/PS films is defined here as the molar fraction of mCzBdBP relative to the total amount of mCzBdBP and mCBP. Because mCzBdBP and mCBP are constitutional isomers, their molar ratio is equal to their weight ratio. The red dashed line represents the position where ΦFRET (S1,H → S1,G) is 50%. Source data are available in the Figshare repository. Quantitative analysis of FRET in analog host-guest systems. a, b Guest concentration dependence of the PL spectra in host–guest systems of mCBP series (a) and DPhCzT series (b). c PL spectral linear-combination fitting results for isomer-doped DPhCzT powder with 0.1 mol% guest concentration. Host FLagg denotes the fluorescence spectra of host aggregates. Methods and detailed data are provided in Section 4.4 and Supplementary Table 9. d, e The spectral overlap between host fluorescence and guest absorption of mCBP (d) and DPhCzT (e) series systems. f FRET efficiency (ΦFRET (S1,H → S1,G)) of all host-guest materials with 1 mol% guest concentration. g Dependence of ΦFRET (S1,H → S1,G) on guest concentration for mCzBdBP/mCBP, DPhBdT/DPhCzT and co-doped polystyrene films of mCzBdBP and mCBP [(mCzBdBP+mCBP)/PS]. For the (mCzBdBP + mCBP)/PS films, the total nominal doping concentration was fixed at 1 wt%. For comparison with the mCzBdBP/mCBP system, the guest concentration in the (mCzBdBP + mCBP)/PS films is defined here as the molar fraction of mCzBdBP relative to the total amount of mCzBdBP and mCBP. Because mCzBdBP and mCBP are constitutional isomers, their molar ratio is equal to their weight ratio. The red dashed line represents the position where ΦFRET (S1,H → S1,G) is 50%. Source data are available in the Figshare repository. ΦFRET and kFRET were extracted for each host–guest sample by linearly deconvoluting the steady-state photoluminescence spectra and quantifying the loss of host fluorescence relative to that of the undoped films (Fig. 7d,e; Supplementary Tables 9, 11 and 12; see Section 4.6.1 for method). Quantitative analysis confirms highly efficient FRET in mCBP series: ΦFRET > 90% at 1 mol% (kFRET ≈ 3.6 × 109 s⁻1) and ~60% even at 0.01 mol% (Fig. 7f,g and Supplementary Fig. 56e–g).The Förster radii (R0) calculated from host-emission/guest-absorption overlap fall in the approximately 1.8 nm (Supplementary Fig. 56h). The fs-TAS confirms fast FRET: the host-singlet ESA band decays within ~100 ps after excitation (Fig. 5 and Supplementary Fig. 50). In contrast, for PS films co-doped with both mCzBdBP and mCBP, (mCzBdBP+mCBP)/PS, with a total concentration of 1 wt% (Supplementary Note 3.12, Supplementary Fig. 57, and Supplementary Table 13, 14), FRET efficiency remains moderate even at high guest loadings (Fig. 7g). For instance, the PS film co-doped with mCzBdBP and mCBP in an equimolar ratio (0.5:0.5) exhibits a ΦFRET of 53%, which is lower than that of the 0.01 mol% mCzBdBP/mCBP small-molecule solid. Given that exciton diffusion is suppressed in the diluted PS matrix, the superior FRET in the mCzBdBP/mCBP system is attributed to robust Förster-type singlet-exciton diffusion (Förster-ED) facilitated by dense molecular packing. In DPhCzT series, ΦFRET only reaches 70–80% at 1 mol% (kFRET ≈ 1.4 × 109 s⁻1) and falls below 50% at ≤0.3 mol%. The corresponding R0 values are approximately 0.8 nm (Supplementary Fig. 56h). Collectively, these data quantitatively explain the efficient host-to-guest FRET in mCBP series and the mixed host–guest emission observed in lightly doped DPhCzT series. Overall, R0 values for the isomer-doped systems are smaller than those in classical efficient FRET systems (R0 > 3 nm)52, likely due to quenching caused by exciton migration among host molecules. Notably, the JFRET between host molecules (S1H → S1H’) is only about one order of magnitude lower than host-to guest JFRET (S1H → S1G) (Supplementary Table 11), indicating that singlet exciton migration within the host matrix is a non-negligible factor. Unlike fluorescence, no host phosphorescence is detected even at low guest concentrations; the host-guest systems still exhibit only the guest phosphorescence (Supplementary Fig. 55). This is mainly because the long-lived host triplet excitons (τP of mCBP/PS: 1.57 s; DPhCzT/PS at 50 K: 5.08 s) can migrate over long distances, greatly increasing the probability of encountering quenchers such as non-emissive impurities and other excitons. Importantly, even at 100 ppm doping, the resulting weak phosphorescence can still be recorded with a standard CCD spectrometer and is visible by naked eye in the dark under intense UV excitation (Supplementary Figs. 31, 32 and 55). Mechanistic analysis of the Cz-derived host/analog-guest systems Based on the above results, we discuss the emission mechanism of the host–guest systems on three hierarchical levels: (i) molecular photophysics of host and guest molecules (Fig. 8a, b, and Supplementary Note 3.13, Supplementary Fig. 58a–c), (ii) exciton diffusion and trapping in the host matrix (Fig. 8c,d), (iii) global exciton dynamics involving charge separation and recombination (Fig. 9). Without inter-CT processes, direct guest excitation leads to photophysical behavior similar to that in PS-doped systems. However, because the host and isomeric guest share similar optical gaps (ΔESS < 0.3 eV), selective guest excitation at low concentrations is impractical, especially under commonly used excitation sources, e.g., 365 nm UV lamp. Therefore, we primarily analyze host excitation followed by energy transfer to the guest.Fig. 8Multiscale emission-mechanistic illustration of analog host-guest systems.a, b Molecular-scale Jablonski diagrams for (a) 1 mol% mCzBdBP/mCBP and (b) 1 mol% DPhBdT/DPhCzT. c, d Corresponding mesoscopic exciton-migration schematic (bottom) for (c) 1 mol% mCzBdBP/mCBP and (d) 1 mol% DPhBdT/DPhCzT. Non-radiative processes that accompany the emission are omitted for clarity. \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\varPhi }_{{{\rm{FRET}}}}$$\end{document}ΦFRET, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\varPhi }_{{{\rm{ISC}}}}$$\end{document}ΦISC denote the quantum efficiency of FRET and the intersystem crossing (ISC). \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\Delta E}_{{{\rm{TT}}}}$$\end{document}ΔETT and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\Delta E}_{{{\rm{ST}}}}$$\end{document}ΔEST represent the host–guest T1 offset and singlet–triplet energy gap, respectively. \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{{{\rm{r}}}}^{{{\rm{S}}}}$$\end{document}krS and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{{{\rm{r}}}}^{{{\rm{T}}}}$$\end{document}krT are the radiative rate constants from the singlet and triplet states, respectively, for both host (H) and guest (G). \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{{{\rm{ISC}}}}$$\end{document}kISC denotes the ISC rate constants. \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{{{\rm{FRET}}},{{\rm{HH}}}}$$\end{document}kFRET,HH is the FRET rate constant between adjacent host molecules. \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{{{\rm{FRET}}},{{\rm{HG}}}}$$\end{document}kFRET,HG and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{{{\rm{PRET}}},{{\rm{HG}}}}$$\end{document}kPRET,HG denote the rate constants of fluorescence and phosphorescence resonance energy transfer (PRET) from the host to the guest via direct pathways. Q represents intrinsic quenchers in the host, such as defects, space charges, or other excitons. Förster-ED and Dexter-ED represent the Förster-type (singlet) and Dexter-type (triplet) exciton diffusion from the host to the guest (HG) or to the quencher (HQ). LD, Förster and DFörster represent the FRET-type exciton diffusion length and diffusion constant (see Section 4.7).Fig. 9Proposed exciton dynamics landscape covering charge separation (CS) and LPL in Cz-based analog host–guest afterglow materials.All delayed fluorescence processes are not shown. Förster-ED and Dexter-ED represent the Förster-type (singlet) and Dexter-type (triplet) exciton diffusion from the host to the guest (HG) or to the quencher (HQ). SSA and TTA denote singlet–singlet annihilation and triplet–triplet annihilation, respectively. CDT & CR represents the charge detrapping and recombination. S0, S1 and T1 represent the ground, lowest singlet and triplet states, respectively. FL, Phos., ISC, Dexter ET and LPL represent fluorescence, phosphorescence, intersystem crossing, Dexter energy transfer and long-persistent luminescence, respectively. Multiscale emission-mechanistic illustration of analog host-guest systems. a, b Molecular-scale Jablonski diagrams for (a) 1 mol% mCzBdBP/mCBP and (b) 1 mol% DPhBdT/DPhCzT. c, d Corresponding mesoscopic exciton-migration schematic (bottom) for (c) 1 mol% mCzBdBP/mCBP and (d) 1 mol% DPhBdT/DPhCzT. Non-radiative processes that accompany the emission are omitted for clarity. \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\varPhi }_{{{\rm{FRET}}}}$$\end{document}ΦFRET, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\varPhi }_{{{\rm{ISC}}}}$$\end{document}ΦISC denote the quantum efficiency of FRET and the intersystem crossing (ISC). \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\Delta E}_{{{\rm{TT}}}}$$\end{document}ΔETT and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\Delta E}_{{{\rm{ST}}}}$$\end{document}ΔEST represent the host–guest T1 offset and singlet–triplet energy gap, respectively. \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{{{\rm{r}}}}^{{{\rm{S}}}}$$\end{document}krS and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{{{\rm{r}}}}^{{{\rm{T}}}}$$\end{document}krT are the radiative rate constants from the singlet and triplet states, respectively, for both host (H) and guest (G). \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{{{\rm{ISC}}}}$$\end{document}kISC denotes the ISC rate constants. \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{{{\rm{FRET}}},{{\rm{HH}}}}$$\end{document}kFRET,HH is the FRET rate constant between adjacent host molecules. \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{{{\rm{FRET}}},{{\rm{HG}}}}$$\end{document}kFRET,HG and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{{{\rm{PRET}}},{{\rm{HG}}}}$$\end{document}kPRET,HG denote the rate constants of fluorescence and phosphorescence resonance energy transfer (PRET) from the host to the guest via direct pathways. Q represents intrinsic quenchers in the host, such as defects, space charges, or other excitons. Förster-ED and Dexter-ED represent the Förster-type (singlet) and Dexter-type (triplet) exciton diffusion from the host to the guest (HG) or to the quencher (HQ). LD, Förster and DFörster represent the FRET-type exciton diffusion length and diffusion constant (see Section 4.7). Proposed exciton dynamics landscape covering charge separation (CS) and LPL in Cz-based analog host–guest afterglow materials. All delayed fluorescence processes are not shown. Förster-ED and Dexter-ED represent the Förster-type (singlet) and Dexter-type (triplet) exciton diffusion from the host to the guest (HG) or to the quencher (HQ). SSA and TTA denote singlet–singlet annihilation and triplet–triplet annihilation, respectively. CDT & CR represents the charge detrapping and recombination. S0, S1 and T1 represent the ground, lowest singlet and triplet states, respectively. FL, Phos., ISC, Dexter ET and LPL represent fluorescence, phosphorescence, intersystem crossing, Dexter energy transfer and long-persistent luminescence, respectively. In the mCBP series compounds, both S1 and T1 are LE states, whereas in the DPhCzT series compounds, the S1 state is the intra-CT state, while the T1 state remains LE (Fig. 8a, b and Supplementary Fig. 58a–c). Owing to the torsional conformation of its biphenyl unit, the mCBP molecule hosts two distinct triplet states: one on the Cz group (3LE2,H) and the other on the biphenyl unit (3LE1,H). Analog guests, with much lower T1 than the corresponding host molecule (ΔETT > 0.5 eV), act as deep emissive traps: the trapped excitons cannot thermally escape and decay through their intrinsic radiative and non-radiative processes. In the DPhCzT series, T1 of DPhCzT lies above the S1 of DPhBdT and DPhBCzT, enabling efficient PRET and PRET-DF. For LE-type mCBP analogs, ISC is much slower than the singlet radiative process (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{{{\rm{ISC}}}}/{k}_{{{\rm{r}}}}^{{{\rm{S}}}}$$\end{document}kISC/krS = 0.01 ~ 0.05), whereas in the intra-CT-type DPhCzT analogs, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{{{\rm{ISC}}}}$$\end{document}kISC becomes comparable to \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{{{\rm{r}}}}^{{{\rm{S}}}}$$\end{document}krS (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{{{\rm{ISC}}}}/{k}_{{{\rm{r}}}}^{{{\rm{S}}}}$$\end{document}kISC/krS = 0.3 ~ 0.5). Therefore, although both series show similar phosphorescence spectra from their Cz-analog segments, ΦPhos in PS is roughly three times higher for the DPhCzT analogs than for the mCBP analogs (Fig. 3h; and Supplementary Table 10). Being heavy-atom-free, all hosts and guests have extremely small triplet radiative rate constants \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$({k}_{{{\rm{r}}}}^{{{\rm{T}}}}\le {1{{\rm{s}}}}^{-1})$$\end{document}(krT≤1s−1) and rigid matrices suppress the triplet non-radiative process (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{{{\rm{nr}}}}^{{{\rm{T}}}}$$\end{document}knrT, Supplementary Table 8), giving second-scale RTP lifetimes. Most primary host singlet excitons undergo FRET to adjacent other host molecules (FRET-HH) or directly to the guest molecule (FRET-HG) rather than decaying on the original host molecule, because kFRET-HH and kFRET-HG exceed host's own \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{{{\rm{r}}}}^{{{\rm{S}}}}$$\end{document}krS, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{{{\rm{ISC}}}}$$\end{document}kISC, and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{{{\rm{nr}}}}^{{{\rm{S}}}}$$\end{document}knrS by over two orders of magnitude (Supplementary Table 8). Successive FRET-HH establish Förster-ED (Fig. 8c, d). Experimentally, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\varPhi }_{{{\rm{FRET}}}}$$\end{document}ΦFRET comprises direct host-to-guest transfer and diffusion-assisted transfer (ΦFRET = ΦFRET–HG + ΦFörster–ED–HG). In the mCBP series, the large contribution of the Förster-ED-HG pathway, evidenced by its long diffusion length (LD, Förster = 5.6 nm vs. 0.96 nm in DPhCzT), accounts for \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\varPhi }_{{{\rm{FRET}}}}$$\end{document}ΦFRET > 90%. Likewise, host triplet excitons can diffuse through the matrix via successive host-to-host Dexter energy transfers, a process referred to as Dexter-type triplet-exciton diffusion (Dexter-ED). Host triplets can in principle diffuse farther via Dexter-ED because of long-lived triplets, but low host ISC efficiency keeps this flux minor, so exciton migration is still dominated by Förster-ED. In TADF-active DPhCzT, a fraction of triplets regenerated to singlets through reverse ISC (RISC) are efficiently delivered to the guest by FRET or Förster-ED, while the rest can reach the guest S1 directly via PRET. As excitons diffuse among the host molecules, they may (i) transfer to guests, (ii) be annihilated non-radiatively by other excitons or polarons (SSA, TTA, TPA, singlet–triplet annihilation, singlet-polaron annihilation, etc.) or (iii) be quenched by non-emissive traps, e.g., structural defects (Fig. 8c, d). For convenience, we define all species that quench host excitons other than the guest as quenchers (Q), encompassing other excitons, polarons, and intrinsic defects. Because triplet Dexter-ED enables much longer diffusion length than singlet Förster-ED, host triplets are more likely quenched, so host phosphorescence is completely suppressed in neat hosts and host–guest mixtures. In the mCBP series, high excitation power further raises the chance of radiative TTA between host and guest, making TTA-DF evident. Figure 9 schematically depicts the global exciton dynamics of the host–guest system with LPL (DF omitted). Under 365 nm excitation, nearly all excitons form on the host. Apart from intrinsic deexcitation and ISC, most initial S₁,H excitons diffuse outward through rapid FRET: some S₁,H excitons migrate to guests, while the remainder are quenched by annihilation (e.g., SSA) or non-emissive impurities (Förster-ED,HQ). Only a small fraction dissociates into charge pairs that are immobilized by two types of carrier traps (e.g., shallow guest HOMO and host LUMO tailed state), producing long-lived CSS. Most initial host triplets from ISC migrate via Dexter-ED, with some captured by guests as deep triplet traps and others quenched. All the above processes unfold within the first ∼1 µs after photoexcitation. Most guest triplets—the secondary T1—originate from the guest's own ISC after FRET, with only a minor fraction transferred from host triplets via Dexter-ED. As deep traps, guest T1 states confine excitons, and in the rigid host matrix their suppressed nonradiative decay together with intrinsically slow radiative rates gives rise to ms–s RTP lifetimes. Nonetheless, some guest triplets can be quenched by diffusing host triplets, lowering ΦPhos. Consequently, the guest phosphorescence-to-fluorescence ratio in host matrices is even lower than in PS films (Supplementary Fig. 58d). After ~10 s, carriers released from deep traps recombine predominantly on hosts, since the low guest content and their predominant role as triplet traps leave only a small fraction available as carrier traps. With high energy transfer efficiency, these regenerated excitons are again transferred to guests and emitted as fluorescence or phosphorescence, producing a faint but long-tailed LPL component. Once all excitons and carriers are exhausted, the system fully relaxes to the ground state, completing the photophysical cycle. Analog of mCBP as a hole trap to enhance p-Type OLPL We next explored whether the analog guest, serving as a hole trap, could enhance the performance of p-type OLPL systems (Fig. 10a). Using a reported 1 mol% MeOTPP/mCBP system as the base13,14,) we introduced varying concentrations of the host isomer mCzBdBP as a second guest. The resulting systems were compared with the original MeOTPP/mCBP system and with a system based on mCBP synthesized from commercial Cz under two excitation conditions: (i) 340 nm to mainly excite the host (Fig. 10b and Supplementary Fig. 59a), and (ii) 450 nm to excite the MeOTPP (Fig. 10c and Supplementary Fig. 59b).Fig. 10The impact of the mCBP analog acting as a hole trap on the long-persistent luminescence (LPL) of p-type organic LPL (OLPL) systems.a Energy-level diagram of the co-doped system and the molecular structure of the first guest (G1, MeOTPP) as the electron acceptor (e acceptor). H and G2 denote host and the second guest, respectively. e donor and h trap represent the electron donor and hole trap, respectively. b, c LPL decay profiles of the p-type OLPL systems (1 mol% MeOTPP/mCBP) based on mCBP hosts synthesized from carbazole synthesized in our laboratory (Lab-Cz) and standard-purity commercial carbazole purchased from Tokyo Chemical Industry (TCI) company (TCI-normal-Cz, C0032, Supplementary Fig. 35), and co-doped systems with varying concentrations of the host isomer. Excitation conditions: (b) 340 nm and (c) 450 nm, 100 μW/cm2 for 1 min. Source data are available in the Figshare repository. The impact of the mCBP analog acting as a hole trap on the long-persistent luminescence (LPL) of p-type organic LPL (OLPL) systems. a Energy-level diagram of the co-doped system and the molecular structure of the first guest (G1, MeOTPP) as the electron acceptor (e acceptor). H and G2 denote host and the second guest, respectively. e donor and h trap represent the electron donor and hole trap, respectively. b, c LPL decay profiles of the p-type OLPL systems (1 mol% MeOTPP/mCBP) based on mCBP hosts synthesized from carbazole synthesized in our laboratory (Lab-Cz) and standard-purity commercial carbazole purchased from Tokyo Chemical Industry (TCI) company (TCI-normal-Cz, C0032, Supplementary Fig. 35), and co-doped systems with varying concentrations of the host isomer. Excitation conditions: (b) 340 nm and (c) 450 nm, 100 μW/cm2 for 1 min. Source data are available in the Figshare repository. The overall LPL intensity increases and then decreases with increasing mCzBdBP doping concentration, with modest changes overall but more pronounced differences in the long-lived component. The maximum enhancement occurs near 0.1 mol%, where the LPL at ~10⁴ s under 340 nm excitation is nearly an order of magnitude higher than in the undoped system. Under 340 nm excitation, guest phosphorescence increases with concentration (up to 1 mol%) (Supplementary Fig. 59a), whereas under 450 nm excitation only LPL is observed, with no guest phosphorescence (Supplementary Fig. 59b). The radical cation absorption of mCzBdBP (Fig. 4d) overlaps only weakly with the CT emission band of MeOTPP/mCBP14, indicating minimal LPL quenching and supporting its role as an effective hole trap in p-type OLPL. Discussion In this work, we systematically unraveled the photophysical mechanisms governing afterglow in two series of Cz-based analog host–guest solids. The pronounced exponential afterglow originates from guest molecules acting as deep triplet traps (ΔETT > 0.5 eV), ensuring exciton confinement and long-lived emission. Although CSS can form under single-photon excitation, their population is extremely small ( ≈ 10⁻4–10⁻3 of triplets) and contributes only to an ultra-weak LPL rather than the main RTP. Because of small singlet-energy gaps and low guest concentrations, host-to-guest energy transfer critically impacts guest emission efficiency, while exciton diffusion within the host adds further energy loss. Consequently, host–guest systems with inefficient energy transfer show lower \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\varPhi }_{{{\rm{phos}}}}$$\end{document}Φphos than guest-doped PS films. As host triplet emission is completely quenched in the solid state, the solids display only weak guest phosphorescence even at trace guest-doping levels ( ≈ 100 ppm), and under strong excitation this faint RTP is still discernible. No aggregate-state enhancement was observed in the DPhCzT series. Nonetheless, compared to PS samples, the structural similarity enables guests to embed into host crystals with minimal disruption, forming dense packing that suppresses oxygen diffusion and allows visible afterglow in air. DF arises via distinct pathways in the two series. In mCBP host–guest solids, DF shows the superlinear intensity-dependence of TTA, becoming prominent only under strong excitation. In contrast, DPhCzT-based systems display single-photon, temperature-independent DF, attributable to phosphorescence resonance energy transfer (PRET) from host T1 to guest S1. Current Cz-isomer host–guest architectures still show only low afterglow efficiencies, leaving room for improvement through molecular design and host–guest pairing engineering, e.g., adopting phosphorescent-OLED design strategies to optimize host–guest energy transfer52. Overall, our findings resolve the mechanism dispute in Cz-based analog afterglow and highlight two outstanding challenges for organic solid-state afterglow: (i) establishing purification and diagnostic protocols that rule out trace triplet-trap contaminants (ppm level at least); (ii) clarifying whether aggregate-specific states (e.g., H-aggregates72,73, self-trapping74,75) contribute to afterglow, and if so, how they form, distribute, and evade exciton-diffusion quenching. Methods Preparation of materials and samples Chemicals 9H-carbazole (Lab-Cz) was synthesized by Lab route 3 in ref. 32. 9H-carbazole (TCI-normal-Cz, C0032; TCI-HP-Cz, C3722), 1H-Benzo[f]indole (Bd, B6283), 5H-Benzo[b]carbazole (BCz, B6453), 2-Chloro-4,6-diphenyl-1,3,5-triazine (DPhClT, C2703) were purchased from Tokyo Chemical Industry (TCI) Co., Ltd. 3,3’-Dibromo-1,1’-biphenyl (mBrBP, QJ-1017) was purchased from Combi-Blocks Inc. All the other reagents and solvents were purchased from commercial sources including TCI, Aldrich, Alfa Aesar, and BLD Chemical. They were of analytical grade and used without purification except as specified. Synthesis and characterization Detailed synthetic procedures and characterization data are provided in Supplementary Note 2. Unless noted, the host materials were synthesized from laboratory-synthesized carbazole (Lab-Cz) following our previously reported procedures32, and were subsequently purified by an additional sublimation step. Sample fabrication Thick films of the mCBP series for optical measurements were fabricated on quartz substrates with a groove (10 × 10 × 0.5 mm) using the melt-casting method under a nitrogen atmosphere at a temperature 10 °C above the melting point of the host material, followed by rapid cooling. The fabricated films were then covered with a quartz cover glass (1 mm thick) and sealed using encapsulation adhesive. The DPhCzT series were obtained as solution-grown crystal powder5,31. Samples of the DPhCzT series for photoluminescence measurements were fabricated by sandwiching the sample powder between two quartz substrates at room temperature. Thin films for the transient absorption test were fabricated by sandwiching the melted samples between two quartz substrates at a temperature 10 °C above the melting point of the host material. All doped PS films were made by the drop-casting method. Characterization and measurement Basic characterization Proton and carbon nuclear magnetic resonance (1H NMR and 13C NMR) spectra for the compounds were attained from a Bruker ARX 400 NMR spectrometer with Chloroform-d (CDCl3) as solvent. High-resolution mass spectra (HRMS) with ESI ionization were recorded on an Agilent 7200 GC-QTOF. Thermal gravimetric analysis (TGA) and differential scanning calorimetry (DSC) were performed with a SHIMADZU DTG-60AH and NETZSCH DSC 204 instrument, respectively, under nitrogen at a heating rate of 10 °C/min. Thermal decomposition temperatures (Td) were determined at 5 % weight loss. Electrochemistry The HOMO and LUMO energy levels of the compounds were derived from their redox potentials measured according to the differential pulse voltammetry (DPV) method described in ref. 15. DPV measurements were carried out using a Pine Research WaveNow wireless potentiostat (AFTP4) inside a nitrogen-filled glovebox. The measurements were conducted in desiccated and oxygen-free dichloromethane (DCM) or dimethylformamide (DMF), with 0.1 mol/L tetrabutylammonium hexafluorophosphate (TBAPF6) as the supporting electrolyte. A platinum wire served as the working electrode, a glassy carbon electrode was used as the counter electrode, and an Ag/Ag⁺ electrode (0.01 mol/L AgNO3 in 0.1 mol/L TBAPF6 acetonitrile solution) was employed as the reference electrode. Redox potentials were referenced against ferrocene/ferrocenium (Fc/Fc+). The DPV curves were obtained with a pulse width (ΔEpulse) of 0.05 V. Before each DPV curve measurement, the working electrode was polished, cleaned, dried and then transferred into a glovebox to ensure a clean surface and eliminate any interference from adsorbed water. The same electrolyte solution was used to measure the redox potentials of the host and guest for HOMO/LUMO comparison. Dilute solutions in the same solvent were prepared to determine their absorption and emission peaks and estimate the optical gap. The electrolyte was chosen to ensure all redox events occurred within its electrochemical window. DMF was selected for most compounds due to its low volatility, good electrolyte solubility, and high ion dissociation. For DPhCzT, whose redox peak exceeds the DMF window, DCM was used instead for both redox and optical measurements. The exciton binding energies (Eb) of compounds were calculated by1\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${E}_{{{\rm{b}}}}={{\rm{IP}}}-{{\rm{EA}}}-{E}_{{{\rm{OG}}}}\approx {E}_{{{\rm{LUMO}}}}-{E}_{{{\rm{HOMO}}}}-{E}_{{{\rm{OG}}}}$$\end{document}Eb=IP−EA−EOG≈ELUMO−EHOMO−EOGwhere IP, EA, and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${E}_{{{\rm{OG}}}}$$\end{document}EOG are the ionization potential, the electron affinity and the optical gap of the compound, respectively. The IP and EA data of the compounds were obtained from electrochemical measurements (Supplementary Note 3.2, Supplementary Fig. 9). The \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${E}_{{{\rm{OG}}}}$$\end{document}EOG data were derived from solution spectroscopy data (Supplementary Figs. 11–13). The absorption spectra of the radical species were obtained under electrical oxidation or reduction (WaveNow Wireless Potentiostat, Pine Research Instrumentation) in a solution containing 0.1 M TBAPF6 by UV-VIS and NIR spectrometers (ULS2048CL-EVO and AvaSpec-NIR256/512-2.5-HSC-EVO, Avantes). Optical measurements UV–vis absorption spectra of materials were obtained on a UV–vis spectrometer (Shimadzu UV-2600) using DCM, toluene and DMF solutions (10 or 50 µmol/L). Photoluminescence (PL) and phosphorescence spectra of solid samples and solutions at room temperature were measured on an Edinburgh Instruments Spectrofluorometer (FLS 1000), an Ocean Optic QE 65 Pro spectrometer with a reflection probe R600-125F or a photonic multichannel analyzer (PMA-12, C10027-02, Hamamatsu Photonics). The phosphorescence spectra and lifetime of the solution at 77 K were recorded on FLS 1000 or PMA-12. For measurements with the PMA-12 spectrometer, 280-nm, 340-nm and 365-nm LEDs (M280L6, M340L5 and M365LP1, Thorlabs) were used as light sources, combined with bandpass filters centered at 280 ± 5 nm, 340 ± 5 nm, and 365 nm ± 5 nm, respectively. The quantum yields of the samples were measured by FLS 1000 with an integrating sphere. Photographs of samples were recorded on a Sony α7sII digital camera with the sample excited using a 365-nm UV lamp at room temperature in air. Time-resolved emission spectra (TRES) Time-resolved transient photoluminescent decay profiles are recorded using an Edinburgh Instruments Spectrofluorometer (FLS 1000) and a time-resolved spectroscopy setup76, composed of a third harmonic wave generation, a Nd:YAG/YVO lasing source (EKSPLA PL-2250, the excitation wavelength of 355 nm, and a pulse width of 30 ps), and a streak camera (C10910-01, Hamamatsu Photonics). The sample was placed in a cryostat (PS-HT-200, Nagase Techno-Engineering) connected to a turbo molecular pump (HiPace 80, Pfeiffer Vacuum), and the temperature was controlled from 10 K to 300 K. Femtosecond transient absorption spectroscopy measurements (fs-TAS) The fs-TAS was performed on a home-built pump−probe set-up. The laser pulse (800 nm, 35 fs pulse width, 1 kHz repetition rate) was generated by a regeneratively amplified Ti:sapphire laser (Coherent Astrella-Tunable-USP, USA). The output of the pulse is divided into two beams with a beam splitter. The 330 or 370 nm pump beams were produced by TOPAS, and the power of the pump pulse was set as 100 or 120 μW. The probe pulse was delayed by a computer-controlled optical delay line and then focused on a thin sapphire plate to generate the white light supercontinuum which was split into two beams by using a broadband 50/50 beam splitter as the signal and reference beams (450 - 750 nm). The focused pump and probe pulses overlapped in a sample film. No photodegradation was observed after fs-TA experiments by checking the steady-state absorption spectra. A transparent amorphous film of mCzBdBP/mCBP was fabricated by melt-casting the blend between two quartz slides. Because this system crystallizes very rapidly, an amorphous film of DPhBdT/DPhCzT could not be obtained. Instead, after melting, a temperature gradient was applied to induce the formation of a semi-transparent crystalline film of DPhBdT/DPhCzT. Millisecond transient absorption spectroscopy measurements (ms-TAS) The transient absorption measurements in the millisecond regime were conducted following the approach described in ref. 11. This method utilizes two light sources: a monochromatic excitation source and a broadband white-light probe. Since the powder samples are optically opaque, we adapted the method from transmission to reflection mode31. Specifically, a BaSO4 reflector was placed behind the sample, and white light was introduced and collected via a reflection fiber probe (R600-125F). The UV excitation light source was positioned at the side of the sample (at an angle of approximately 60°), as illustrated in Supplementary Fig. 60. A key consideration in this setup is the distance between the reflection fiber probe and the sample. On one hand, this distance affects the illumination area and intensity of the white-light probe, which diverges from the fiber tip. On the other hand, it also impacts the intensity of the reflected signal. Additionally, the material exhibits phosphorescence emission around 600 nm within the 300–1100 nm detection window of ms-TAS, which may interfere with the absorption signal in that spectral region. Although the UV-LED excitation sources (310 nm and 340 nm) used in our setup are collimated and can uniformly cover the entire sample area, the distance between the fiber probe and the sample significantly influences the balance between excited-state absorption (ESA) and phosphorescence signals in the ms-TAS spectra. To minimize these effects, we optimized the probe–sample distance to ensure that the white-light spot fully covers the sample while maintaining sufficient signal intensity without saturating the detector. For measurements, we first recorded a baseline reflectance spectrum under white-light-only conditions, including the background reflectance spectrum (without the sample, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${I}_{{{\rm{RB}}}}$$\end{document}IRB) and the sample reflectance spectrum (with the sample in place, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${I}_{{{\rm{RS}}}}$$\end{document}IRS). The ground-state absorption spectrum was calculated from these two measurements according to \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${A}_{{{\rm{G}}}}=-{{\mathrm{lg}}}\left({I}_{{{\rm{RS}}}}/{I}_{{{\rm{RB}}}}\right)$$\end{document}AG=−lgIRS/IRB. Subsequently, under identical conditions, we turned on the excitation source and measured the corresponding reflectance spectrum \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$({I}_{{{\rm{RSE}}}})$$\end{document}(IRSE). To maintain consistency, the same background reflectance spectrum obtained in the first step was used. Finally, the ms-TAS was derived as the difference between the absorption spectra recorded before \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$({A}_{{{\rm{G}}}})$$\end{document}(AG) and after excitation \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$({A}_{{{\rm{E}}}}=-{{\mathrm{lg}}}\left({I}_{{{\rm{RSE}}}}/{I}_{{{\rm{RB}}}}\right)):\Delta A={A}_{{{\rm{E}}}}-{A}_{{{\rm{G}}}}=-{{\mathrm{lg}}}\left({I}_{{{\rm{RSE}}}}/{I}_{{{\rm{RS}}}}\right)$$\end{document}(AE=−lgIRSE/IRB):ΔA=AE−AG=−lgIRSE/IRS. Afterglow measurements The afterglow decay profiles and spectra were recorded using a home-built, high-sensitivity measurement setup (Supplementary Fig. 33a) including the following detectors: a photon counting head (H11890, Hamamatsu Photonics) without further wavelength sensitivity calibration for measuring decay signals of afterglow and either a multichannel photodetector (PMA-12, C10027-02, Hamamatsu Photonics) or a multi-channel spectrometer (QE-Pro, Ocean) for recording afterglow spectra. To maximize the sensitivity of the afterglow signal, the distance between the sample and photon-counting head, and the optical path of the side of the photon-counting head is simplified (e.g., no wavelength-resolving components are included in the optical path for afterglow decay signal measurement). Samples were made on a quartz substrate with a groove (10 × 10 × 0.5 mm) placed in a dark chamber of this measurement setup for room temperature measurements. Samples were excited by various wavelengths of LEDs (M280L6, M340L5, M365LP1, M455L4, Thorlabs) with bandpass filters (280 ± 5 nm, 340 ± 5 nm, 365 ± 5 nm, 450 nm ± 5 nm, Thorlabs or Edmund Optics) with a specific excitation intensity and duration. LED excitation intensity was measured with a power meter (S120VC, Thorlabs). The ND filter wheel contained five filters: OD0.3, OD1, OD2, OD3, and OD4. The intensity calibration curve was obtained using a UV-VIS spectrometer (ULS2048CL-EVO, Avantes). The optical fiber probe equipped with a cosine corrector was placed at the same position as the photon counting head. To construct the calibration curve, we measured the light intensity at six levels using a xenon lamp and five sets of ND filters. For each intensity level, the signal from the photon counting head (equipped with additional OD3 and OD4 filters) was corrected using the manufacturer-provided sensitivity curve to obtain the integrated intensity (counts s−1) over the 400–861 nm range. In parallel, the UV-VIS spectrometer was used to record the spectral irradiance (μW cm−2 nm)), which was then integrated over the same 400–861 nm range (μW cm−2). By comparing the two sets of values under identical experimental conditions, the calibration curve was obtained. All afterglow signals were baseline-corrected using instrument readings recorded before and after the emission measurements, ensuring that the baseline of all displayed afterglow intensities is zero. Specifically, after placing the sample in the setup, the system was kept in the dark for 5 minutes. Prior to excitation, a baseline reading (Baseline 1) was recorded with the ND filter wheel positioned at an open (non-ND) setting to capture the instrument’s dark signal. Following afterglow acquisition (30 minutes to 1 hour, or longer depending on the duration of the sample’s afterglow), a second baseline reading (Baseline 2) was taken. When the setup is properly light-tight, the detector dark current is stable, and the sample emission has decayed below the detection limit, the average of Baselines 1 and 2 is expected to be consistent. This average value was then used to correct the afterglow signal intensity. Quantitative analysis method of component proportions in the steady-state PL spectrum To determine the relative contributions of different emissive species to the steady-state photoluminescence (PL) spectrum, we employ a linear combination fitting approach based on photon number analysis. This method is applicable once each component spectrum that constitutes the system’s PL has been clearly resolved, for example, by time-resolved emission spectroscopy. The fundamental principle of this method is that the photon number in a steady-state PL spectrum composed of multiple emissive components is equal to the sum of the photon numbers of each individual component. Accordingly, the measured steady-state PL spectrum can be expressed as the weighted sum of all component spectra:2\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\frac{d{n}_{{\mbox{tar}}}(E)}{{dE}}={\sum }_{i=1}^{n}{A}_{i}\frac{d{n}_{i}(E)}{{dE}}$$\end{document}dntar(E)dE=∑i=1nAidni(E)dEwhere \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\frac{{{dn}}_{{{\rm{tar}}}}({E})}{{dE}},\,\frac{{{dn}}_{i}\left(E\right)}{{dE}}$$\end{document}dntar(E)dE,dniEdE denote the photon number distribution as a function of photon energy (E) of the target and the reference components, respectively. Ai are regression coefficients that represent the relative photon contribution of each component \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$({\varphi }_{{{\rm{i}}}})$$\end{document}(φi). The total photon number of the target spectrum \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$({n}_{{\mbox{tar}}})$$\end{document}(ntar) can be expressed as a weighted sum of the total photon numbers of the reference components \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$({n}_{i})$$\end{document}(ni):3\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${n}_{{\mbox{tar}}}={\sum }_{i=1}^{n}{A}_{i}{n}_{i}$$\end{document}ntar=∑i=1nAini The constraint condition of \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${A}_{i}$$\end{document}Ai is given by:4\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\sum }_{i=1}^{n}{A}_{i}=1\,\left(0\le {A}_{i}\le 1\right)$$\end{document}∑i=1nAi=10≤Ai≤1 To facilitate comparison and fitting across spectra acquired using different instruments or conditions, all spectra are further normalized such that their total photon number is set to unity \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$(\widetilde{n}=1)$$\end{document}(n~=1), then:5\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\frac{d\widetilde{n}\left(E\right)}{{dE}}=\frac{I\left(E\right)}{\int I\left(E\right){dE}}$$\end{document}dn~EdE=IE∫IEdEwhere \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\frac{d\widetilde{n}\left(E\right)}{{dE}}$$\end{document}dn~EdE represents an emission spectrum normalized to the spectral area and I(E) is the measured spectral intensity as a function of photon energy E. This normalization ensures that all spectra (target and reference) satisfy \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\widetilde{n}}_{{\mbox{tar}}}={\widetilde{n}}_{{\mbox{i}}}=1$$\end{document}n~tar=n~i=1. By inserting the normalized target PL spectrum together with the normalized spectra of all components into Eqs. (2)–(4) and performing a linear regression, one can determine the fractional contribution \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${A}_{i}$$\end{document}Ai of each component spectrum. For emission spectra expressed as a function of wavelength \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$(I\left(\lambda \right))$$\end{document}(Iλ), the Jacobian transformation \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$(I\left(E\right)=-I(\lambda ){hc}/{E}^{2})$$\end{document}(IE=−I(λ)hc/E2)77 makes it possible to rewrite Eqs. (2) and (5) in the following equivalent form:6\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\frac{{d}{{{n}}}_{{\rm{tar}}}({{\rm{\lambda }}})}{{{d}}{{\lambda }}}={\sum }_{{{i}}=1}^{{{n}}}{{{A}}}_{{{i}}}\frac{{{d}}{{{n}}}_{{{\rm{i}}}}({{\lambda }})}{{{d}}{{\rm{\lambda }}}}$$\end{document}dntar(λ)dλ=∑i=1nAidni(λ)dλ7\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\frac{d\widetilde{n}\left(\lambda \right)}{d\lambda }=\frac{I\left(\lambda \right)}{\int I\left(\lambda \right)d\lambda }$$\end{document}dn~λdλ=Iλ∫Iλdλwhere \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\frac{d{n}_{{{\rm{tar}}}}(\lambda )}{d\lambda },\,\frac{d{n}_{i}(\lambda )}{d\lambda }$$\end{document}dntar(λ)dλ,dni(λ)dλ denote the photon number distribution as a function of wavelength (λ) of the target and the reference components, respectively. Since the steady-state spectra and the component spectra may be measured using different instruments, resulting in mismatched wavelength points, interpolation is required to ensure all spectra share a common set of wavelength values before fitting. This approach enables a quantitative decomposition of the steady-state emission into physically meaningful components, with the obtained coefficients \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${A}_{i}$$\end{document}Ai directly corresponding to the photon contributions \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$({\varphi }_{{{\rm{i}}}})$$\end{document}(φi) from each emissive species. Furthermore, the quantum yields of different emissive components \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$({\varPhi }_{{{\rm{i}}}})$$\end{document}(Φi), such as fluorescence and phosphorescence, can be calculated based on the following relationship:8\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\varPhi }_{{{\rm{i}}}}={\varPhi }_{{{\rm{PL}}}}{\varphi }_{{{\rm{i}}}}$$\end{document}Φi=ΦPLφiwhere \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\varPhi }_{{{\rm{PL}}}}$$\end{document}ΦPL is the total photoluminescence quantum yield. Using this method, we determined the fluorescence \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$({\varPhi }_{{FL}}^{{PS}})$$\end{document}(ΦFLPS) and RTP \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$({\varPhi }_{{phos}}^{{PS}})$$\end{document}(ΦphosPS) quantum yields of the doped PS films, and separately obtained the quantum yields of host fluorescence \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$({\varPhi }_{{FL},H}^{H})$$\end{document}(ΦFL,HH), guest fluorescence \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$({\varPhi }_{{FL},G}^{H})$$\end{document}(ΦFL,GH), and guest RTP \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$({\varPhi }_{{phos},G}^{H})$$\end{document}(Φphos,GH) in the host–guest systems. The contribution of LPL in these materials was neglected here, as it is over four orders of magnitude weaker than RTP (Fig. 4a,b), which itself accounts for only a small fraction of the total emission. This method requires high-quality spectra. For spectra with significant noise, appropriate denoising techniques must be applied without distorting the spectral shape. Spectra with rich fine structures are more favorable for accurate fitting using this method. However, when an emission component makes up only a trace fraction of the overall photoluminescence, rendering its signal barely above the noise floor, the method can no longer reliably isolate and quantify that component. Moreover, it is not applicable to different emissive species with highly similar spectral profiles, such as fluorescence and TADF. In such cases, their relative contributions can be determined using time-resolved emission decay profiles (Supplementary Fig. 19c)78. Furthermore, this method does not consider distortions in the onset region of steady-state spectra caused by self-absorption. In this work, self-absorption is relatively weak, and neglecting it has little impact on the linear regression results. However, for materials with significant self-absorption, proper correction is necessary to obtain reliable fitting results. Notably, self-absorption has a negligible effect on transient spectral shapes. Calculation of fundamental photophysical constants Since all compounds discussed in this work (except DPhCzT) exhibit ΔEST values larger than 0.5 eV, the RISC process can be safely neglected79. The fundamental photophysical parameters of the compound at low concentrations in toluene solution and in PS films under oxygen-free conditions are related as follows:9\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{{{\rm{F}}}}=1/{\tau }_{{{\rm{F}}}}={k}_{{{\rm{r}}}}^{{{\rm{S}}}}+{k}_{{{\rm{nr}}}}^{{{\rm{S}}}}+{k}_{{{\rm{ISC}}}}$$\end{document}kF=1/τF=krS+knrS+kISC10\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{{{\rm{P}}}}=1/{\tau }_{{{\rm{P}}}}={k}_{{{\rm{r}}}}^{{{\rm{T}}}}+{k}_{{{\rm{nr}}}}^{{{\rm{T}}}}$$\end{document}kP=1/τP=krT+knrT11\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\varPhi }_{{{\rm{F}}}}=\frac{{k}_{{{\rm{r}}}}^{{{\rm{S}}}}}{{k}_{{{\rm{r}}}}^{{{\rm{S}}}}+{k}_{{{\rm{nr}}}}^{{{\rm{S}}}}+{k}_{{{\rm{ISC}}}}}$$\end{document}ΦF=krSkrS+knrS+kISC12\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\varPhi }_{{{\rm{P}}}}=\frac{{\varPhi }_{{{\rm{ISC}}}}{k}_{{{\rm{r}}}}^{{{\rm{T}}}}}{{k}_{{{\rm{r}}}}^{{{\rm{T}}}}+{k}_{{{\rm{nr}}}}^{{{\rm{T}}}}}$$\end{document}ΦP=ΦISCkrTkrT+knrT13\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\varPhi }_{{{\rm{ISC}}}}=\frac{{k}_{{{\rm{ISC}}}}}{{k}_{{{\rm{r}}}}^{{{\rm{S}}}}+{k}_{{{\rm{nr}}}}^{{{\rm{S}}}}+{k}_{{{\rm{ISC}}}}}$$\end{document}ΦISC=kISCkrS+knrS+kISCwhere \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{{{\rm{F}}}}$$\end{document}kF and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{{{\rm{P}}}}$$\end{document}kP are the rate constants for fluorescence and phosphorescence, respectively; \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\varPhi }_{{{\rm{F}}}},{\varPhi }_{{{\rm{P}}}}$$\end{document}ΦF,ΦP, and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\varPhi }_{{{\rm{ISC}}}}$$\end{document}ΦISC are the quantum yields of fluorescence, phosphorescence, and ISC process. \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{{{\rm{r}}}}^{{{\rm{S}}}},{k}_{{{\rm{nr}}}}^{{{\rm{S}}}}$$\end{document}krS,knrS, and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{{{\rm{ISC}}}}$$\end{document}kISC represent the radiative, non-radiative, and ISC rate constants from the lowest singlet excited state, respectively, while \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{{{\rm{r}}}}^{{{\rm{T}}}}$$\end{document}krT and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{{{\rm{nr}}}}^{{{\rm{T}}}}$$\end{document}knrT are the radiative and non-radiative rate constants from the lowest triplet state. We can determine parameters such as \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{{{\rm{r}}}}^{{{\rm{S}}}},{k}_{{{\rm{r}}}}^{{{\rm{T}}}},{k}_{{{\rm{ISC}}}}$$\end{document}krS,krT,kISC and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\varPhi }_{{{\rm{ISC}}}}$$\end{document}ΦISC using the following equations, based on the experimentally measured values of \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{{{\rm{F}}}},{k}_{{{\rm{P}}}},{\varPhi }_{{{\rm{F}}}}$$\end{document}kF,kP,ΦF and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\varPhi }_{{{\rm{P}}}}$$\end{document}ΦP.14\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{{{\rm{r}}}}^{{{\rm{S}}}}={\varPhi }_{{{\rm{F}}}}{k}_{{{\rm{F}}}}$$\end{document}krS=ΦFkF15\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\varPhi }_{{{\rm{ISC}}}}={\varPhi }_{{{\rm{P}}}}\left(1+\frac{{k}_{{{\rm{nr}}}}^{{{\rm{T}}}}}{{k}_{{{\rm{P}}}}}\right)$$\end{document}ΦISC=ΦP1+knrTkP16\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{{{\rm{r}}}}^{{{\rm{T}}}}=\frac{{\varPhi }_{{{\rm{P}}}}{k}_{{{\rm{P}}}}}{{\varPhi }_{{{\rm{ISC}}}}}$$\end{document}krT=ΦPkPΦISC17\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{{{\rm{ISC}}}}={k}_{{{\rm{F}}}}{\varPhi }_{{{\rm{ISC}}}}$$\end{document}kISC=kFΦISC To calculate \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\varPhi }_{{{\rm{ISC}}}}$$\end{document}ΦISC, it is necessary to know \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{{{\rm{nr}}}}^{{{\rm{T}}}}$$\end{document}knrT too, which is typically assumed to be much smaller than \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{{{\rm{r}}}}^{{{\rm{T}}}}$$\end{document}krT in the solid state (especially in crystalline form19), and thus often neglected. However, in our case, PS films were used, and at room temperature, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{{{\rm{nr}}}}^{{{\rm{T}}}}$$\end{document}knrT may not be negligible. As an alternative, it is reasonable to assume that \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{{{\rm{nr}}}}^{{{\rm{T}}}}$$\end{document}knrT in toluene at 77 K is negligible. Due to the similarity between toluene and PS, the \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{{{\rm{nr}}}}^{{{\rm{T}}}}$$\end{document}knrT at room temperature in PS can be estimated using:18\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{{{\rm{nr}}},{{\rm{PS}}},{{\rm{rt}}}}^{{{\rm{T}}}}\approx {k}_{{{\rm{P}}},{{\rm{PS}}},{{\rm{rt}}}}-{k}_{{{\rm{P}}},{{\rm{tolu}}},77{{\rm{K}}}}$$\end{document}knr,PS,rtT≈kP,PS,rt−kP,tolu,77K For example, the measured phosphorescence lifetime \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$({\tau }_{{{\rm{P}}}})$$\end{document}(τP) of DPhCzT is 5.4 s in toluene at 77 K and 5.1 s in PS at 50 K, supporting this assumption. \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\varPhi }_{{{\rm{ISC}}}},{k}_{{{\rm{r}}}}^{{{\rm{T}}}},{k}_{{{\rm{ISC}}}}$$\end{document}ΦISC,krT,kISC in PS at room temperature can then be calculated using Eqs. (15)- (17). For the sake of consistency and clarity in our discussion, we assume that the ISC efficiency and rate constant of the guest molecules in the host matrix are the same as those in PS. Calculation of rate constant of resonance energy transfer, Förster integral and radius In this study, the absorption spectra of guest molecules are red-shifted relative to the host. If the excitation wavelength only excites the guest without affecting the host, the system behaves similarly to guest-doped PS, with the host merely providing a rigid environment. However, if the excitation wavelength falls within the absorption range of the host, the host molecules will predominantly absorb the energy and subsequently transfer it to the guest molecules. Therefore, it is necessary to evaluate the energy transfer efficiency from host to guest under such conditions. Since the phosphorescence contribution in the emission spectrum of our system is minimal, the ISC process of host is inefficient, indicating that energy transfer occurs mainly via fluorescence resonance energy transfer (FRET). The FRET rate (kFRET) and efficiency (ΦFRET) can be calculated as follows:19\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{{{\rm{FRET}}}}={k}_{{{\rm{F}}}}^{{{\rm{D}}}}{\left(\frac{{R}_{0}^{{{\rm{SS}}}}}{r}\right)}^{6}$$\end{document}kFRET=kFDR0SSr620\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\varPhi }_{{{\rm{FRET}}}}=\frac{{k}_{{{\rm{FRET}}}}}{{k}_{{{\rm{F}}}}^{{{\rm{D}}}}+{k}_{{{\rm{FRET}}}}}=\frac{1}{1+{\left(r/{R}_{0}^{{{\rm{SS}}}}\right)}^{6}}$$\end{document}ΦFRET=kFRETkFD+kFRET=11+r/R0SS6where \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{{{\rm{F}}}}^{{{\rm{D}}}}$$\end{document}kFD is the apparent fluorescence rate constant of the energy donor (including non-radiative transitions) in the absence of the energy acceptor. For the host–guest doped systems discussed in this work, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{{{\rm{F}}}}^{{{\rm{D}}}}$$\end{document}kFD was determined from the fluorescence lifetime of the neat host material. r is the distance between the energy donor and acceptor. \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${R}_{0}^{{{\rm{SS}}}}$$\end{document}R0SS is the Förster radius of FRET and can be calculated using:21\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${R}_{0}^{{{\rm{SS}}}}=\root{{6}}\of{\frac{9\,{{\mathrm{ln}}}\,10}{{2}^{7}{\pi }^{5}{N}_{{{\rm{A}}}}}\frac{{\kappa }^{2}}{{n}^{4}}{\varPhi }_{{{\rm{FD}}}}{J}_{{{\rm{FRET}}}}}$$\end{document}R0SS=9ln1027π5NAκ2n4ΦFDJFRET622\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${J}_{{{\rm{FRET}}}}=\frac{{\int }_{0}^{\infty }{I}_{{{\rm{D}}}}\left(\lambda \right){\varepsilon }_{{{\rm{A}}}}\left(\lambda \right){\lambda }^{4}d\lambda }{{\int }_{0}^{\infty }{I}_{{{\rm{D}}}}\left(\lambda \right)d\lambda }$$\end{document}JFRET=∫0∞IDλεAλλ4dλ∫0∞IDλdλwhere, ΦFD is the total fluorescence quantum yield of the donor without the presence of the energy acceptor. For the host–guest doped systems discussed in this work, ΦFD was determined from the fluorescence quantum yield of the neat host material. JFRET is the Förster integral of FRET which represents the spectral overlap integral between the normalized fluorescence spectrum of the energy donor \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$({I}_{{{\rm{FD}}}}\left(\lambda \right)/{\int }_{0}^{\infty }{I}_{{{\rm{FD}}}}\left(\lambda \right)d\lambda )$$\end{document}(IFDλ/∫0∞IFDλdλ) and the molar extinction coefficient spectrum of the energy acceptor \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$({\varepsilon }_{A}\left(\lambda \right))$$\end{document}(εAλ). We processed the original spectral data according to the above requirements and performed numerical integration to obtain the JFRET value. n is the refractive index of the host material. For mCBP, n was taken as the average value of 1.8266 over the 370–600 nm range as reported in ref. 80. For DPhCzT, n was assumed to be 1.881. The orientation factor κ2 describes the relative spatial orientation between the transition dipole moments of the donor and acceptor. For amorphous organic solids, κ2 is typically taken as 0.47682. For crystalline materials, κ2 can be calculated using the following expression:23\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\kappa }^{2}={\left(\cos {\theta }_{{{\rm{T}}}}-3\cos {\theta }_{{{\rm{D}}}}\cos {\theta }_{{{\rm{A}}}}\right)}^{2}$$\end{document}κ2=cosθT−3cosθDcosθA2where θT is the angle between the emission transition dipole of the energy donor and the absorption transition dipole of the energy acceptor, θD and θA are the angles between these dipoles and the vector joining the energy donor and acceptor. For DPhCzT, θT = 0° and θD = θA = 80.9°5, resulting in a κ2 value of 0.856. In calculating the FRET rate constant between adjacent host molecules in the neat host samples (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{{{\rm{FRET}}},{{\rm{HH}}}}$$\end{document}kFRET,HH), we used the shortest intermolecular distance in the crystal structure of the host material: for mCBP, r = 0.416 nm28; for DPhCzT, r = 0.338 nm5. Since the donor radiative rate constant (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{{{\rm{F}}}}^{{{\rm{D}}}}$$\end{document}kFD) should reflect the unaggregated state in this case, we used the values measured in PS films. However, for DPhCzT, which exhibits aggregation even at low concentrations in PS, the \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{{{\rm{F}}}}^{{{\rm{D}}}}$$\end{document}kFD value measured in toluene solution was used as an approximation. The rate constant (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{{{\rm{PRET}}}}$$\end{document}kPRET) and efficiency (\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\varPhi }_{{{\rm{PRET}}}}$$\end{document}ΦPRET) of phosphorescence resonance energy transfer (PRET) from the host triplet state (T1,H) to the guest singlet state (S1,G) can be estimated using the following relation. Since both FRET and PRET take place within the same host–guest system, the host molecules at the excited state (S1,H, T1,H) exhibit the same spatial distribution relative to the guest molecules at the ground state (S0,G); therefore, their average separations \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left\langle r\right\rangle$$\end{document}r are equal, i.e., \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left\langle {r}_{{TS}}\right\rangle=\left\langle {r}_{{SS}}\right\rangle$$\end{document}rTS=rSS:24\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{{{\rm{PRET}}}}={k}_{{{\rm{P}}}}^{{{\rm{D}}}}{\left(\frac{{R}_{0}^{{{\rm{TS}}}}}{r}\right)}^{6}={k}_{{{\rm{FRET}}}}\frac{{k}_{{{\rm{P}}}}^{{{\rm{D}}}}}{{k}_{{{\rm{F}}}}^{{{\rm{D}}}}}{\left(\frac{{R}_{0}^{{{\rm{TS}}}}}{{R}_{0}^{{{\rm{SS}}}}}\right)}^{6}$$\end{document}kPRET=kPDR0TSr6=kFRETkPDkFDR0TSR0SS625\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${R}_{0}^{{{\rm{TS}}}}=\root{{6}}\of{\frac{9\,{{\mathrm{ln}}}\,10}{{2}^{7}{\pi }^{5}{N}_{{{\rm{A}}}}}\frac{{\kappa }^{2}}{{n}^{4}}{\varPhi }_{{{\rm{PD}}}}\,{J}_{{{\rm{PRET}}}}}$$\end{document}R0TS=9ln1027π5NAκ2n4ΦPDJPRET626\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${J}_{{{\rm{PRET}}}}=\frac{{\int }_{0}^{\infty }{I}_{{{\rm{PD}}}}\left(\lambda \right){\varepsilon }_{{{\rm{A}}}}\left(\lambda \right){\lambda }^{4}d\lambda }{{\int }_{0}^{\infty }{I}_{{{\rm{PD}}}}\left(\lambda \right)d\lambda }$$\end{document}JPRET=∫0∞IPDλεAλλ4dλ∫0∞IPDλdλ27\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\varPhi }_{{{\rm{PRET}}}}=\frac{{k}_{{{\rm{PRET}}}}}{{k}_{{{\rm{P}}}}^{{{\rm{D}}}}+{k}_{{{\rm{PRET}}}}}$$\end{document}ΦPRET=kPRETkPD+kPRETwhere \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{{{\rm{P}}}}^{{{\rm{D}}}}$$\end{document}kPD is the observed phosphorescence rate constant of the energy donor (including non-radiative transitions) in the absence of the energy acceptor. ΦPD was determined from the phosphorescence quantum yield of the neat host material. JPRET is the Förster integral of PRET, which represents the spectral overlap integral between the normalized phosphorescence spectrum of the energy donor \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$({I}_{{{\rm{PD}}}}\left(\lambda \right)/{\int }_{0}^{\infty }{I}_{{{\rm{PD}}}}\left(\lambda \right)d\lambda )$$\end{document}(IPDλ/∫0∞IPDλdλ) and the molar extinction coefficient spectrum of the energy acceptor \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$({\varepsilon }_{A}\left(\lambda \right))$$\end{document}(εAλ). A Steady-state method for calculating FRET efficiency from host to guest in aggregated materials To calculate FRET quantum efficiency using the above method, the donor–acceptor distance r must be known. However, in the aggregated materials discussed in this study, r is distributed and varies dynamically as excitons migrate, making it difficult to determine precisely. Based on our experimental results, no intermolecular charge-transfer (inter-CT) processes occur in our system, although a negligible fraction of charge separation (CS) events is observed. This indicates that after doping, FRET becomes the sole additional energy dissipation pathway from the host singlet state relative to the undoped system. Therefore, for the undoped system, the fluorescent quantum yield:28\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\varPhi }_{{{\rm{FD}}}}=\frac{{k}_{{{\rm{r}}}}^{{{\rm{SD}}}}}{{k}_{{{\rm{r}}}}^{{{\rm{SD}}}}+{k}_{{{\rm{IC}}}}^{{{\rm{SD}}}}+{k}_{{{\rm{ISC}}}}^{{{\rm{D}}}}+{k}_{{{\rm{CS}}}}^{{{\rm{D}}}}+{k}_{{{\rm{q}}}}}=\frac{{k}_{{{\rm{r}}}}^{{{\rm{SD}}}}}{{k}_{{{\rm{F}}}}^{{{\rm{D}}}}}$$\end{document}ΦFD=krSDkrSD+kICSD+kISCD+kCSD+kq=krSDkFDwhere \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{{{\rm{r}}}}^{{{\rm{SD}}}},{k}_{{{\rm{IC}}}}^{{{\rm{SD}}}},{k}_{{{\rm{ISC}}}}^{{{\rm{D}}}}$$\end{document}krSD,kICSD,kISCD, and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{{{\rm{CS}}}}^{{{\rm{D}}}}$$\end{document}kCSD denote the radiative, internal conversion, ISC and exciton dissociation rate constants of the S1 state of the energy donor, respectively. \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{{{\rm{q}}}}$$\end{document}kq is an equivalent rate constant that approximates the combined effect of all quenching processes induced by singlet exciton migration among host molecules. These processes may include, but are not limited to, reaction with defects, singlet–singlet annihilation (SSA), singlet–triplet annihilation (STA), and singlet–polaron annihilation (SPA), although individual contributions are not explicitly distinguished here. For the system doped with the heteromolecular guest as the energy acceptor, the fluorescent quantum yield of the energy donor:29\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\varPhi }_{{{\rm{FDA}}}}=\frac{{k}_{{{\rm{r}}}}^{{{\rm{SD}}}}}{{k}_{{{\rm{r}}}}^{{{\rm{SD}}}}+{k}_{{{\rm{IC}}}}^{{{\rm{SD}}}}+{k}_{{{\rm{ISC}}}}^{{{\rm{D}}}}+{k}_{{{\rm{CS}}}}^{{{\rm{D}}}}+{k}_{{{\rm{q}}}}+{k}_{{{\rm{FRET}}}}}=\frac{{k}_{{{\rm{r}}}}^{{{\rm{SD}}}}}{{k}_{{{\rm{F}}}}^{{{\rm{D}}}}+{k}_{{{\rm{FRET}}}}}$$\end{document}ΦFDA=krSDkrSD+kICSD+kISCD+kCSD+kq+kFRET=krSDkFD+kFRETwhere, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{{{\rm{FRET}}}}$$\end{document}kFRET specifically refers to the host-to-guest FRET process and does not include FRET between host molecules. Thus, the FRET quantum efficiency can be calculated as:30\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\varPhi }_{{{\rm{FRET}}}}=1-\frac{{\varPhi }_{{{\rm{FDA}}}}}{{\varPhi }_{{{\rm{FD}}}}}$$\end{document}ΦFRET=1−ΦFDAΦFD Experimentally, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\varPhi }_{{{\rm{FDA}}}}$$\end{document}ΦFDA is obtained by:31\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\varPhi }_{{{\rm{FDA}}}}={\varPhi }_{{{\rm{PL}}}}{\varphi }_{{{\rm{FD}}}}$$\end{document}ΦFDA=ΦPLφFDwhere \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\varPhi }_{{{\rm{PL}}}}$$\end{document}ΦPL is the total photoluminescence quantum yield of the doped system, and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\varphi }_{{{\rm{FD}}}}$$\end{document}φFD is the fraction of the donor’s fluorescence within the total emission spectrum of the doped system. In this work, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\varphi }_{{{\rm{FD}}}}$$\end{document}φFD was obtained using the method described in Section 4.4. Furthermore, from the FRET efficiency \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\varPhi }_{{{\rm{FRET}}}}$$\end{document}ΦFRET obtained with this method, the mean donor–acceptor distance can be determined using Eq. (20), and the energy-transfer rate constant kFRET can then be calculated with Eq. (19) or32\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{{{\rm{FRET}}}}=\frac{{k}_{{{\rm{F}}}}^{{{\rm{D}}}}}{\frac{1}{{\varPhi }_{{{\rm{FRET}}}}}-1}$$\end{document}kFRET=kFD1ΦFRET−1where the \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{{{\rm{F}}}}^{{{\rm{D}}}}$$\end{document}kFD value used for calculating \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{{{\rm{FRET}}},{{\rm{HG}}}}$$\end{document}kFRET,HG was determined from the neat host sample. This method (Eq. 30) follows the same rationale as Equation 13.13 in ref. 83. \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\varPhi }_{{{\rm{FRET}}}}$$\end{document}ΦFRET is obtained by assessing how the donor’s fluorescence changes once the acceptor is introduced. The difference is that we evaluate this change via the donor’s fluorescence quantum yield, which is experimentally easier to determine. By contrast, the alternative route—using changes in the donor’s fluorescence lifetime (Eq. 13.14 in ref. 83)—is experimentally challenging when the acceptor’s fluorescence lifetime exceeds the donor’s, because in such cases it is difficult to accurately isolate the donor’s intrinsic radiative rate constant within the donor–acceptor mixture. Note that this method yields the overall energy transfer efficiency from the S1,H to the S1,G via RET, including processes where excitons first undergo Förster-type diffusion among host molecules and are then transferred to the guest S1,G via FRET. The presence of Förster exciton diffusion can effectively shorten the donor–acceptor distance by enabling excitons to migrate toward acceptors, thereby increasing the probability of energy transfer. Once the exciton migrates within the Förster radius, direct FRET from host to guest becomes the dominant pathway. As a result, the average donor–acceptor separation distance between energy donors and acceptors () calculated by this method is expected to be smaller than the average initial separation between excitons in the host and the guest molecules. However, since exciton migration on the host occurs in a random manner, at low guest concentrations—especially under high photon flux excitation—direct FRET still dominates, while diffusion primarily contributes to exciton quenching. Moreover, this method assumes that the ISC process of the host remains unchanged upon guest doping, which holds true at low guest concentrations but may not be valid at higher doping levels. Calculation of exciton diffusion length and diffusivity Based on the isotropic medium assumption and the nearest-neighbor random walk model on a simple cubic lattice with side length a, the Förster RET-type exciton diffusivity (DFörster) can be calculated according to ref. 52:33\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${D}_{{{\rm{F}}}\!{{{\rm{o}}}}^{{\mathrm{.}}.}\!{{\rm{rster}}}}=\frac{1}{6}{k}_{{{\rm{FRET}}},{{\rm{HH}}}}\cdot {a}^{2}$$\end{document}DFo..rster=16kFRET,HH⋅a2where the value of a was taken as the shortest intermolecular distance in the crystal structure of the host material: for mCBP, a = 0.416 nm28; for DPhCzT, a = 0.338 nm5. The Förster RET-type exciton diffusion length (LD,Förster) can be described as:34\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${L}_{{{\rm{D}}},{{\rm{F}}}\!{{{\rm{o}}}}^{{\mathrm{.}}.}\!{{\rm{rster}}}}=\sqrt{{D}_{{{\rm{F}}}\!{{{\rm{o}}}}^{{\mathrm{.}}.}\!{{\rm{rster}}}}{\tau }_{{{\rm{D}}}}}=\frac{{{R}_{0}}^{3}}{\sqrt{6}{a}^{2}}$$\end{document}LD,Fo..rster=DFo..rsterτD=R036a2where \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\tau }_{{{\rm{D}}}}$$\end{document}τD is the natural recombination lifetime of the exciton of the energy donor. Disentangling FRET from co-excitation of the energy donor and acceptor (for Supplementary Fig. 57j) Consider a homogeneous energy donor (D) / acceptor (A) mixture excited at \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\lambda }_{{{\rm{exc}}}}$$\end{document}λexc. Let \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${N}_{0}$$\end{document}N0 be the number of incident excitation photons. The photoluminescence quantum yield (PLQY) is defined on the basis of absorbed photons:35\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\varPhi }_{{{\rm{tot}}}}\equiv \frac{{N}_{{{\rm{em}}}}}{{N}_{{{\rm{abs}}}}}$$\end{document}Φtot≡NemNabswhere \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${N}_{{{\rm{em}}}}$$\end{document}Nem and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${N}_{{{\rm{abs}}}}$$\end{document}Nabs are the total emitted and absorbed photon numbers, respectively. Let \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${N}_{{{\rm{em}}},{{\rm{D}}}}$$\end{document}Nem,D and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${N}_{{{\rm{em}}},{{\rm{A}}}}$$\end{document}Nem,A be the photon numbers emitted from the donor and acceptor fluorescence channels, obtained from spectral decomposition of the steady-state PL spectrum. We then define the observed donor and acceptor fluorescence yields per absorbed photon as36\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\varPhi }_{{{\rm{FDA}}},{{\rm{obs}}}}\equiv \frac{{N}_{{{\rm{em}}},{{\rm{D}}}}}{{N}_{{{\rm{abs}}}}}$$\end{document}ΦFDA,obs≡Nem,DNabs37\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\varPhi }_{{{\rm{FAD}}},{{\rm{obs}}}}\equiv \frac{{N}_{{{\rm{em}}},{{\rm{A}}}}}{{N}_{{{\rm{abs}}}}}$$\end{document}ΦFAD,obs≡Nem,ANabs At \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\lambda }_{{{\rm{exc}}}}$$\end{document}λexc, let the molar extinction coefficients of the donor and acceptor be \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\varepsilon }_{{{\rm{D}}}}({\lambda }_{{{\rm{exc}}}})$$\end{document}εD(λexc) and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\varepsilon }_{{{\rm{A}}}}({\lambda }_{{{\rm{exc}}}})$$\end{document}εA(λexc) (in \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${{\rm{L}}}\,{{\rm{mo}}}{{{\rm{l}}}}^{-1}\,{{\rm{c}}}{{{\rm{m}}}}^{-1}$$\end{document}Lmol−1cm−1), and their molar concentrations in the film be \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${c}_{{{\rm{D}}}}$$\end{document}cD and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${c}_{{{\rm{A}}}}$$\end{document}cA (in \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${{\rm{mol}}}\,{{{\rm{L}}}}^{-1}$$\end{document}molL−1), respectively. The corresponding absorption coefficients are38\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\alpha }_{{{\rm{D}}}}={{\mathrm{ln}}}\,(10)\,{\varepsilon }_{{{\rm{D}}}}({\lambda }_{{{\rm{exc}}}})\,{c}_{{{\rm{D}}}}$$\end{document}αD=ln(10)εD(λexc)cD39\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\alpha }_{{{\rm{A}}}}={{\mathrm{ln}}}\,(10)\,{\varepsilon }_{{{\rm{A}}}}({\lambda }_{{{\rm{exc}}}})\,{c}_{{{\rm{A}}}}$$\end{document}αA=ln(10)εA(λexc)cA40\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\alpha }_{{{\rm{tot}}}}={\alpha }_{{{\rm{D}}}}+{\alpha }_{{{\rm{A}}}}$$\end{document}αtot=αD+αA For a homogeneous mixture, the fractions of absorbed photons initially absorbed by the acceptor and donor are given by41\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${P}_{{{\rm{A}}}}\equiv \frac{{N}_{{{\rm{abs}}},{{\rm{A}}}}}{{N}_{{{\rm{abs}}}}}=\frac{{\alpha }_{{{\rm{A}}}}}{{\alpha }_{{{\rm{tot}}}}}=\frac{{\varepsilon }_{{{\rm{A}}}}({\lambda }_{{{\rm{exc}}}})\,{c}_{{{\rm{A}}}}}{{\varepsilon }_{{{\rm{A}}}}({\lambda }_{{{\rm{exc}}}})\,{c}_{{{\rm{A}}}}+{\varepsilon }_{{{\rm{D}}}}({\lambda }_{{{\rm{exc}}}})\,{c}_{{{\rm{D}}}}}$$\end{document}PA≡Nabs,ANabs=αAαtot=εA(λexc)cAεA(λexc)cA+εD(λexc)cD42\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${P}_{{{\rm{D}}}}\equiv \frac{{N}_{{{\rm{abs}}},{{\rm{D}}}}}{{N}_{{{\rm{abs}}}}}=\frac{{\alpha }_{{{\rm{D}}}}}{{\alpha }_{{{\rm{tot}}}}}=\frac{{\varepsilon }_{{{\rm{D}}}}({\lambda }_{{{\rm{exc}}}})\,{c}_{{{\rm{D}}}}}{{\varepsilon }_{{{\rm{A}}}}({\lambda }_{{{\rm{exc}}}})\,{c}_{{{\rm{A}}}}+{\varepsilon }_{{{\rm{D}}}}({\lambda }_{{{\rm{exc}}}})\,{c}_{{{\rm{D}}}}}$$\end{document}PD≡Nabs,DNabs=αDαtot=εD(λexc)cDεA(λexc)cA+εD(λexc)cDso that \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${P}_{{{\rm{A}}}}+{P}_{{{\rm{D}}}}=1$$\end{document}PA+PD=1. Notably, these fractions are independent of the overall absorption magnitude \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$1-{e}^{-{\alpha }_{{{\rm{tot}}}}l}$$\end{document}1−e−αtotl and depend only on the relative absorption strengths of the two species at \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\lambda }_{{{\rm{exc}}}}$$\end{document}λexc. In the following derivation, we assume that (i) the fluorescence quantum yield of the acceptor, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\varPhi }_{{{\rm{FA}}}}$$\end{document}ΦFA, is determined solely by the population of \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${{{\rm{S}}}}_{1,{{\rm{A}}}}$$\end{document}S1,A and is independent of whether this state is reached by direct excitation or by FRET; (ii) \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\varPhi }_{{{\rm{FD}}}}$$\end{document}ΦFD denotes the intrinsic donor fluorescence quantum yield measured in the absence of energy transfer under identical conditions; and (iii) \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\varPhi }_{{{\rm{FRET}}}}$$\end{document}ΦFRET is defined as the fraction of donor-absorbed excitations that are transferred to the acceptor and subsequently contribute to acceptor fluorescence. Step 1: Donor and acceptor FRET in the presence of co-excitation Upon excitation, a fraction \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${P}_{{{\rm{D}}}}({P}_{{{\rm{A}}}})$$\end{document}PD(PA) of the absorbed photons initially excites the donor (acceptor). Donor excitations are transferred to the acceptor with a probability \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\varPhi }_{{{\rm{FRET}}}}$$\end{document}ΦFRET. Assuming that the fluorescence quantum yields \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\varPhi }_{{{\rm{FD}}}}$$\end{document}ΦFD and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\varPhi }_{{{\rm{FA}}}}$$\end{document}ΦFA are intrinsic to the donor and acceptor, respectively, the observed fluorescence yields per absorbed photon are given by43\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\varPhi }_{{{\rm{FDA}}},{{\rm{obs}}}}={\varPhi }_{{{\rm{FD}}}}{P}_{{{\rm{D}}}}(1-{\varPhi }_{{{\rm{FRET}}}})\,$$\end{document}ΦFDA,obs=ΦFDPD(1−ΦFRET)44\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\varPhi }_{{{\rm{FAD}}},{{\rm{obs}}}}={\varPhi }_{{{\rm{FA}}}}\left({P}_{{{\rm{A}}}}+{P}_{{{\rm{D}}}}{\varPhi }_{{{\rm{FRET}}}}\right)$$\end{document}ΦFAD,obs=ΦFAPA+PDΦFRET Step 2: Definition and calculation of \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${Y}_{A}$$\end{document}YA We define45\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${Y}_{{{\rm{A}}}} {=} ^{{{\mathrm{def}}}} \frac{{\varPhi }_{{{\rm{FAD}}},{{\rm{obs}}}}}{{P}_{{{\rm{A}}}}}$$\end{document}YA=defΦFAD,obsPAwhich removes the trivial contribution from direct acceptor absorption. Substituting Eq. (44) into Eq. (45) gives46\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${Y}_{{{\rm{A}}}}={\varPhi }_{{{\rm{FA}}}}\left(1+{\varPhi }_{{{\rm{FRET}}}}\frac{{\varepsilon }_{{{\rm{D}}}}\left({\lambda }_{{{\rm{exc}}}}\right){c}_{{{\rm{D}}}}}{{\varepsilon }_{{{\rm{A}}}}\left({\lambda }_{{{\rm{exc}}}}\right){c}_{{{\rm{A}}}}}\right)$$\end{document}YA=ΦFA1+ΦFRETεDλexccDεAλexccA From Eq. (43),47\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\varPhi }_{{{\rm{FRET}}}}=1-\frac{{\varPhi }_{{{\rm{FDA}}},{{\rm{obs}}}}}{{P}_{{{\rm{D}}}}{\varPhi }_{{{\rm{FD}}}}}$$\end{document}ΦFRET=1−ΦFDA,obsPDΦFDwhich can be used for calculating \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\varPhi }_{{{\rm{FRET}}}}$$\end{document}ΦFRET from experimental data. Step 3: Parameterization of \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\varPhi }_{{{\rm{FRET}}}}$$\end{document}ΦFRET and derivation of fitting functions To obtain a closed-form fitting function with the acceptor concentration as the sole independent variable, the FRET process was parameterized adopting the Förster model for a static, random three-dimensional distribution of donor–acceptor separations, as is appropriate for dilute host–guest systems in a rigid polymer matrix84,85. According to this model, the relative donor fluorescence yield in the presence of acceptors is given by:48\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\varPhi }_{{{\rm{FDA}}}}/{\varPhi }_{{{\rm{FD}}}}=1-\sqrt{\pi }\gamma \exp \left({\gamma }^{2}\right){{\rm{erfc}}}\left(\gamma \right)$$\end{document}ΦFDA/ΦFD=1−πγexpγ2erfcγwhere49\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${{\rm{erfc}}}\left(\gamma \right)\equiv 1-\frac{2}{\sqrt{\pi }}\int _{0}^{\gamma }\exp \left(-{x}^{2}\right){{\rm{d}}}x$$\end{document}erfcγ≡1−2π∫0γexp−x2dx50\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\gamma={c}_{{{\rm{A}}}}/{c}_{{{\rm{A}}}}^{0}$$\end{document}γ=cA/cA0 Here, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${c}_{{{\rm{A}}}}$$\end{document}cA is the acceptor concentration with units of moles per liter, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${c}_{{{\rm{A}}}}^{0}$$\end{document}cA0 is the “critical transfer concentration” of the acceptor and given by51\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${c}_{{{\rm{A}}}}^{0}=1500{\pi }^{3/2}/{N}_{{{\rm{A}}}}{R}_{0}^{3}$$\end{document}cA0=1500π3/2/NAR03where \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${N}_{{{\rm{A}}}}$$\end{document}NA is the number of molecules per mole. \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${R}_{0}$$\end{document}R0 is the Förster radius expressed in centimeters. Because \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\varPhi }_{{{\rm{FDA}}}}/{\varPhi }_{{{\rm{FD}}}}$$\end{document}ΦFDA/ΦFD represents the fraction of donor excitations that remain on the donor, the corresponding FRET efficiency is given by the complementary expression52\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\varPhi }_{{{\rm{FRET}}}}=\sqrt{\pi }\frac{{c}_{{{\rm{A}}}}}{{c}_{{{\rm{A}}}}^{0}}\exp \left[{\left(\frac{{c}_{{{\rm{A}}}}}{{c}_{{{\rm{A}}}}^{0}}\right)}^{2}\right]{{\rm{erfc}}}\left(\frac{{c}_{{{\rm{A}}}}}{{c}_{{{\rm{A}}}}^{0}}\right)$$\end{document}ΦFRET=πcAcA0expcAcA02erfccAcA0 Equation 52 provides an explicit functional form of \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\varPhi }_{{{\rm{FRET}}}}({c}_{{{\rm{A}}}})$$\end{document}ΦFRET(cA), which can be directly substituted into the general expressions derived above to fit the experimental data. Substituting Eq. 52 into the general expression for \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${Y}_{{{\rm{A}}}}$$\end{document}YA derived above yields the following closed-form fitting function:53\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${Y}_{{{\rm{A}}}}({c}_{{{\rm{A}}}})={\varPhi }_{{FA}}\left\{1+\sqrt{\pi }\frac{{\varepsilon }_{{{\rm{D}}}}\left({\lambda }_{{{\rm{exc}}}}\right){c}_{{{\rm{D}}}}}{{\varepsilon }_{{{\rm{A}}}}\left({\lambda }_{{{\rm{exc}}}}\right){c}_{{{\rm{A}}}}^{0}}\exp \left[{\left(\frac{{c}_{{{\rm{A}}}}}{{c}_{{{\rm{A}}}}^{0}}\right)}^{2}\right]{{\rm{erfc}}}\left(\frac{{c}_{{{\rm{A}}}}}{{c}_{{{\rm{A}}}}^{0}}\right)\right\}$$\end{document}YA(cA)=ΦFA1+πεDλexccDεAλexccA0expcAcA02erfccAcA0where \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${c}_{{{\rm{D}}}}={c}_{{{\rm{tot}}}}-{c}_{{{\rm{A}}}}$$\end{document}cD=ctot−cA, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${c}_{{{\rm{tot}}}}$$\end{document}ctot is a constant in our case. Equations 52 and 53 provide closed-form fitting functions with \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${c}_{{{\rm{A}}}}$$\end{document}cA as the only independent variable and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${c}_{{{\rm{A}}}}^{0}$$\end{document}cA0 as the key adjustable parameter. Quantum chemical calculations (for Supplementary Fig. 21c–f) Quantum chemical calculations were conducted using the Gaussian 16 Rev. B.01 package86. The geometry and electronic properties of ground states were optimized using density functional theory (DFT) at the B3LYP/6-311 G level of theory. The excited states were computed using time-dependent DFT (TD-DFT) at the same B3LYP/6-311 G level and then analyzed using Multiwfn87 and VMD programs88. Supplementary information Supplementary Information Transparent Peer Review file Supplementary Information Transparent Peer Review file