Design of Flexible Conformal Beam-Scanning Leaky-Wave Antenna Authors: Jiahao Liu, Yiming Liu, Shuang Ma, Qilin Ren, Ya Fan, Zhongjie Wu, Xuebin Wang Published: 2026 ABSTRACT This paper presents a flexible conformal beam-scanning leaky-wave antenna (LWA) array based on a PI-ABS composite substrate and spoof surface plasmon polariton (SSPP) structure for Ku-band (12–18 GHz) applications. The proposed design features periodically symmetric gradient linear metallic stubs and interleaved tapered radiating patches to realize efficient SSPP slow-wave transmission, −1st spatial harmonic radiation, and open-stopband (OSB) suppression simultaneously. Benefiting from the flexible PI-ABS composite structure, the antenna maintains stable radiation performance under different curvatures, overcoming the mechanical instability and beam-scanning sensitivity of conventional flexible LWAs. The four-element conformal array achieves continuous beam scanning from −67° to 32° with a peak gain of 16.5 dBi and radiation efficiency above 58% across the entire band. Both simulation and measurement results validate that the proposed design integrates flexible conformality, wideband beam scanning, and high radiation efficiency, providing a novel solution for conformal wireless communication systems. 1. Introduction In modern communication and detection systems [1], traditional rigid antennas can no longer meet practical demands. Compared to conventional rigid antennas, flexible antennas [2] can better conform to carrier surfaces, effectively reducing the antenna’s impact on mechanical structures. With the development of flexible [3] dielectric materials, antennas can better adapt to various types of curved substrates [4]. Furthermore, to enable optimal electromagnetic wave [5,6] reception under different motion states, research on the beam-scanning capability of antennas is of great significance. LWAs, with their advantages of controllable beam scanning, compact structure, and high radiation efficiency, can precisely match the coverage demands of dynamic signals in communication. Therefore, this paper address the limitations of traditional LWAs by developing a novel type of flexible conformal LWA [7] based on flexible dielectric substrates [8], forming an array configuration [9]. This approach balances flexibility and beam-scanning capability [10]. Typically, pre-fabricated rigid dielectric substrates can be used for conformal antennas. However, due to the rigidity of such materials, their curvature is fixed after fabrication, making them unable to adapt to surfaces with varying curvatures. This challenge can be overcome by employing flexible materials with stable performance and excellent bending characteristics. Materials such as polyethylene terephthalate (PET), polydimethylsiloxane (PDMS) [11], and PI are widely used as dielectric substrates for conformal antennas. By printing the antenna pattern onto these flexible dielectric substrates, they can conform well to curved substrates. PI is a high-performance organic polymer material featuring a low relative permittivity and excellent tensile properties, enabling it to conform well to curved substrates. Substrates with a lower permittivity can moderately increase the bandwidth of antennas while providing favorable impedance characteristics [12,13]. Acrylonitrile Butadiene Styrene (ABS), a common engineering plastic, offers excellent mechanical strength, formability, and cost-effectiveness. The combination of ABS and PI endows the antenna with both flexible characteristics and structural support stability. Current research on LWAs primarily focuses on optimizing beam scanning [14] range, suppressing open-stopband interference, and mitigating electromagnetic interference [15]. However, relevant studies on conformal bending [16] remain scarce, and existing designs have obvious practical deficiencies. On one hand, existing flexible LWAs are predominantly based on a single layer of flexible substrate. While bendable, these lack sufficient mechanical strength, which leads to structural instability after long-term deformation and thus degrades the antenna performance [17,18]. This often results in discrepancies between the simulation and physical test results. On the other hand, traditional conformal [19] LWAs exhibit beam their beam-scanning capabilities are highly sensitive to curvature changes, frequently leading to issues such as sudden gain drops, unwanted electromagnetic interference [20], and scanning angle deviations. To address these deficiencies, this paper proposes a novel continuous beam-scanning LWA [21,22] based on a PI-ABS composite flexible substrate integrated with an SSPP structure. First, the performance trends of a single LWA under different curvatures are simulated and verified, and the array antenna is physically tested on a substrate with a specific target curvature. Benefiting from the structural support of the PI-ABS composite substrate, the array can maintain good flexibility while conforming to the target curved surfaces, enabling extensive and stable beam scanning [23,24,25]. The proposed flexible conformal LWA array achieves continuous scanning from –67° rearward to 32° forward at 12–18 GHz, which outperforms most existing designs and is verified by physical tests. The main novelties of this work are summarized as follows: Material innovation: A PI-ABS composite flexible substrate is proposed, which combines the flexibility of PI and the mechanical support of ABS, solving the contradiction between antenna conformality and structural stability. Structural innovation: Gradient SSPP gradient linear metallic stubs and interleaved tapered radiating patches are cooperatively designed, which realizes smooth mode transition, wideband radiation, and OSB suppression simultaneously. Performance innovation: The conformal array achieves an ultra-wide beam-scanning range of −67° to 32° in 12–18 GHz, which outperforms most reported conformal LWAs. 2. Antenna Structure The proposed conformal antenna array comprises four LWAs operating from 12 GHz to 18 GHz. Each LWA features identical structural parameters and element distribution. This uniformity contributes to the coupling between LWAs while also providing a structural foundation for subsequent conformal arrays. Figure 1a illustrates the top view of the LWA, and its 3D hierarchical view is presented in Figure 1b. From top to bottom, the LWA consists of the antenna pattern printed on PI, the PI layer, the ABS layer, and the copper ground plane. The PI layer serves as the dielectric substrate of the radiating structure and is the key medium enabling antenna flexibility. It has a relative permittivity of εr = 3.5, a loss tangent of tanδ = 0.002, and a thickness of h1 = 0.1 mm. These properties satisfy the bending requirements of the subsequent conformal array antenna while providing a low-loss platform for the metallic radiating pattern. A 1 mm thick ABS layer is employed as a supporting structure to compensate for the insufficient mechanical rigidity of the PI layer. Its favorable mechanical strength and shock resistance ensure the structural integrity of the antenna. The metallic pattern printed on the PI layer constitutes the radiation core of the antenna, which primarily consists of the feed structure, the SSPP transmission line, and a set of interleaved tapered radiating patches. Detailed parameters are shown in Table 1 below. The conformal array comprises, from top to bottom, a metallic layer printed on a PI substrate, a PI dielectric layer, an ABS dielectric layer, and a copper ground plane. All layers share a uniform curvature radius of 100 mm. The conformal array consists of eight ports. Similarly to the single-LWA configuration, each port is equipped with tapered microstrip matching networks at both ends to provide standard 50 Ω coaxial interfaces for SMA connectors. These networks facilitate efficient mode conversion and ensure impedance matching with the SSPP transmission line. The 3D hierarchical view of the conformal antenna array is shown in Figure 2. The spacing between two adjacent LWAs is set to 5.2 mm (d = 5.2 mm), corresponding to the half-wavelength spacing at the maximum frequency of 18 GHz. 3. Antenna Design Principles and Analysis 3.1. Single-Antenna Design: Leaky-Wave Radiation Mechanism Based on SSPP SSPP is a type of artificial surface wave that simulates the transmission mode of surface plasmons through artificial periodic metallic structures. Since the SSPP on metallic branch units behaves as a slow wave and cannot radiate by itself, periodic perturbations must be introduced in accordance with the LWA theory for one-dimensional periodic structures. This converts the guided SSPP on metallic branch units into a Floquet wave, whose phase constant is given by βn=β0+2πn/P, where β0 denotes the fundamental mode of the Floquet wave, n is the order of the spatial harmonic (n = 0, ±1, ±2, ±3, …), and P is the perturbation period. Periodic modulation can shift the original dispersion curve to excite an infinite number of spatial harmonics. Furthermore, through appropriate modulation, a specific harmonic branch can be tuned to the fast-wave region to satisfy the radiation condition of β−1