Recent Advances in Biomass-Derived Activated Carbon and Biochar for Tetracycline Removal from Water: A Comprehensive Review Authors: Hari Om Singh, Ramesh Vinayagam, Raja Selvaraj Published: 2026 ABSTRACT Here, we review the recent advancements in the use of sustainable carbon materials, namely, activated carbon (AC) and biochar (BC), for the adsorption of tetracycline (TC) from aqueous media. The environmental persistence of TC and its role in promoting antimicrobial resistance have necessitated the development of efficient, scalable, and sustainable treatment solutions. AC and BC, synthesized from agricultural and industrial biomass waste, offer high specific surface areas, tunable porosity, and surface functionalities that make them highly effective for TC removal. This review presents a comprehensive evaluation of biomass selection, synthesis routes, activation strategies, and surface modifications that influence the structural and chemical characteristics of these adsorbents. Key adsorption mechanisms such as π–π electron donor–acceptor interactions, hydrogen bonding, electrostatic interactions, surface complexation, and pore filling are critically discussed in relation to environmental parameters, including pH, ionic strength, and contaminant speciation. In addition, adsorption kinetics and isotherm models are analyzed to elucidate the underlying transport and binding processes. Finally, we identify current challenges and future opportunities in optimizing AC and BC for real-world applications in wastewater treatment systems. This review aims to serve as a scientific foundation for the rational design of next-generation carbon-based materials for effective antibiotic removal and environmental protection. Introduction Freshwater scarcity and water pollution are escalating global challenges driven by climate change, population growth, industrialization, and intensive chemical usage in healthcare, which threaten sustainable development and food security. Antibiotics have changed modern medicine by making many serious infections treatable. Among them, tetracycline (TC) is one of the most widely used because it is broad-spectrum, inexpensive, and effective. It continues to be produced in large quantities for both human and veterinary use. However, this heavy use has also increased the amount of TC that enters the environment. In many regions, conventional wastewater treatment plants are not designed to completely remove pharmaceuticals; therefore, effluents containing TC can reach natural water bodies. These discharges may contain unmetabolized TC, transformation products formed during use or treatment, and other pharmaceutical residues. Over time, such substances can persist and accumulate in water and soil, posing potential risks to ecosystems and public health, including the development and spread of antimicrobial resistance. Because a considerable fraction of TC is excreted in its active form, it can enter municipal and hospital wastewater. In anaerobic digestion systems, TC can undergo adsorption onto sludge as well as biodegradation by anaerobic microorganisms, which together govern its fate during wastewater treatment. In livestock systems, manure from treated animals is another important source; when this manure is stored or applied to fields, TC residues can runoff into surface waters or percolate into groundwater (Figure ). Even though environmental concentrations are usually low, these residues can still disturb microbial communities and promote the selection and spread of antibiotic-resistance genes, which is a recognized public health concern. In natural waters and soils, TC binds strongly to natural organic matter and mineral surfaces, which influences its mobility, persistence, and bioavailability; uptake by organisms and possible transfer through the food chain raise further long-term ecological concerns. The relatively stable structure of TC and the presence of multiple functional groups also make it difficult to remove by using conventional treatment processes. Although awareness of pharmaceutical pollution is increasing, regulations remain limited: organizations such as the World Health Organization (WHO) and the Environmental Protection Agency (EPA) provide broad water-quality guidelines, but TC-specific discharge standards and routine monitoring requirements are often lacking. Pathways of TC contamination in the environment from anthropogenic and agricultural sources to water systems (Created in BioRender). Several conventional methods are used to remove antibiotics from wastewater, such as electrochemical oxidation, filtration processes, catalytic degradation, membrane separation, ion exchange, and adsorption. Among these, adsorption is often preferred because the operation is simple, the energy demand is relatively low, and high removal efficiencies can be achieved without generating large amounts of secondary waste. For TC, a variety of adsorbents have been studied, including activated carbon (AC), biochar (BC), carbon nanotubes (CNTs), metal–organic frameworks (MOFs), zeolites, and graphene oxide. CNTs, MOFs, and graphene-based materials can provide very high specific surface areas and adjustable surface chemistry, but their large-scale use is limited by costly precursors, multistep synthesis routes, and concerns about environmental safety. Zeolites can remove contaminants by ion exchange and adsorption, but they usually show limited affinity for neutral or weakly polar organic molecules such as TC unless their surface is modified. In practical applications, AC and BC are still widely used because they are comparatively inexpensive, can be produced from abundant feedstocks, and have a good record in removing different pollutants. AC generally has a more developed pore structure and higher surface area, whereas BC is increasingly considered as a more sustainable option due to its low-cost and resource-efficient production. Despite extensive work on TC adsorption, many reviews either discuss antibiotic removal at a generalized level or restrict their scope to individual adsorbent types, which reduces their relevance for real-world process design and optimization. In particular, there is still no clear side-by-side comparison of AC and BC for TC removal. Both materials have shown good potential, but current work rarely brings together information on their preparation routes, surface properties, pore structures, and functional groups in relation to adsorption performance. This review aims to fill that gap by summarizing recent advances in the use of AC and BC for TC removal from water. It covers different synthesis and activation methods, including physical and chemical activation and low-temperature pyrolysis, and discusses key physicochemical features such as specific surface area, pore volume, and surface chemistry. Adsorption behavior is interpreted using common kinetic and isotherm models, with attention to mechanisms such as hydrogen bonding, π–π interactions, and electrostatic attraction. The effects of operating conditions, including pH, initial TC concentration, contact time, and temperature, are also considered. By linking adsorption performance with practical aspects of material preparation and use, this review offers a consolidated basis for developing efficient and sustainable AC- and BC-based adsorbents for TC removal in water treatment. This review focuses on TC as a representative compound of the TC-class antibiotics; extension to other derivatives (e.g., doxycycline) is beyond the present scope and is proposed as future work. Methodology A structured review was undertaken to compile evidence of biomass-derived AC and BC for TC removal from aqueous systems. The review considered biomass sources, synthesis/activation approaches, characterization outcomes, and the reported adsorption performance. The literature was retrieved from Scopus and Google Scholar by searching the title, abstract, and keyword fields with the Boolean query: (“activated carbon”) AND (“biochar”) AND (“tetracycline” AND “adsorption”) AND (“biomass”). The query was chosen to capture studies explicitly linking biomass-based AC/BC preparation to TC adsorption applications. Persistence, Resistance, and Regulatory Implications of TC in Aquatic Systems Since 2002, antibiotic use worldwide has expanded dramatically. Earlier reports described global antibiotic consumption in terms of mass, typically ∼100,000–200,000 tonnes per year. By 2020, usage was increasingly quantified using the public-health metric defined daily doses (DDDs), with global consumption estimated at ∼4.5 trillion DDDs. Use of TC has also been substantial: the European Union documented around 2294 tons for medical purposes in 1997, and U.S. veterinary applications exceeded 3200 tons by 2001. After therapeutic use, a substantial fraction of TC is excreted unmetabolized. Because conventional wastewater treatment plants (WWTPs) are not specifically designed to fully remove such micropollutants, a portion can pass through treatment processes and be discharged into receiving waters. Its high-water solubility and low volatility favor persistence in aquatic systems, increasing the likelihood of prolonged exposure. Continued inputs of TC and related compounds can encourage the emergence and spread of antibiotic-resistance genes (ARGs) through mutation and horizontal gene transfer in microbial communities. TC-resistance genes such as tet­(O) and tet­(S) have been detected in human gut microbiota and in various environmental samples, indicating potential public-health implications. In Europe, resistance levels as high as 66.9% in Escherichia coli and 44.9% in Klebsiella spp. have been reported. Studies from North America and Asia similarly describe the presence of genes including tet­(M), tet­(Q), and tet­(W) in wastewater, rivers, and waters affected by aquaculture, and E. coli from U.S. dairy manure has shown almost universal resistance. The global occurrence of TC in water bodies is supported by measured concentrations at different sites. Reported levels include 280–540 ng/L in Iranian municipal wastewater, 5.3 ng/L in WWTP effluent in North America, and 21 ng/L in the Soeste River in Germany. Such differences reflect regional usage patterns and the limits of current wastewater treatment systems. Residual TC concentrations in various water sources worldwide are summarized in Table . 1Residual Concentrations of TC in Different Water SourcesS.Nowater sourcereported TC concentration (ng/L)countryrefs.1Municipal wastewater280 to 540Iran 2Wastewater treatment systems5.3North America 3Soeste river21Germany 4Hanoi Lake101Hanoi, Vietnam 5Drinking water source11.16China 6Hospital effluent1385Norway 7Aquaculture water180Thailand 8Hospital wastewater42.2Portugal 9Urban water100Australia Residual Concentrations of TC in Different Water Sources The regulation of TC in water has therefore become an important environmental and public-health issue. Its persistence, widespread use, and ability to promote antibiotic resistance are central concerns. In many countries, however, specific regulatory limits for TC in drinking water and wastewater are still lacking. Where guidance exists, it generally aims to keep TC at trace levels, often in the ng/L to low μg/L range, to reduce long-term exposure and ecological pressure that favors resistant bacteria. As new toxicological and environmental data become available, regulatory agencies are moving toward stricter standards and more consistent monitoring of TC in different water bodies. For example, Antos et al. reported that TC levels in European surface waters are generally in the 0–20 ng/L range. Zhou et al. examined TC at environmentally relevant concentrations (3.9–250 ng/mL) and showed that exposure within this window can increase the conjugative transfer of antibiotic-resistance genes (ARGs), potentially intensifying antimicrobial-resistance risks. At higher concentrations, Taşkan found that 0.25–30 mg/L TC can suppress sensitive algal populations, with implications for aquatic ecosystem function. Taken together, these studies indicate that TC may pose ecological and health-related concerns across a wide concentration range, including at trace levels. This evidence strengthens the case for treatment approaches that can reliably remove TC at low concentrations, particularly as monitoring expectations and discharge requirements evolve. Among the available options, AC and BC have received sustained interest because their adsorption behavior can be tuned through surface area, pore structure, and surface functional groups. In this review, we focus on biomass-derived AC and BC as practical sorbents for TC control in water systems. The next sections summarize their preparation routes and key properties, and then discuss how these factors translate into adsorption performance in aqueous media. Biomass Feedstocks and Activation Methods AC Synthesis The performance of AC is closely linked to the nature of the biomass feedstock, since the precursor composition largely determines how the carbon framework and surface groups develop during activation. Many low-cost resources, such as agricultural residues, industrial byproducts, and food-processing wastes, have been converted into AC with good adsorption properties. In addition, ACs that are hybridized or surface-modified often show improved uptake because new functional groups and reactive sites can be introduced, creating a combined (synergistic) effect. In general, AC can be prepared from a wide range of carbon-rich materials, including coal, wood, nutshells, peat, and other plant-based residues, and its pore structure and surface chemistry can be tuned by the activation route. Prior to activation, the raw precursor shows typical lignocellulosic characteristics with abundant oxygen-containing groups. In chemical activation, the precursor is impregnated with reagents such as H3PO4, ZnCl2, KOH, H2SO4, or HNO3, followed by carbonization at 400–900 °C, which helps control surface functionalities and promotes micropore development. After carbonization, oxygen-containing surface groups such as carboxyl, hydroxyl, carbonyl, and C–O functionalities can be detected; moreover, chemical activation can generate distinct surface moieties, including −OH, −CO, −PO, and −P–O–C functionalities under H3PO4 activation, while KOH activation is often evidenced by the appearance of peaks associated with more oxygen-containing functional groups. The activating chemical plays a major role in shaping the final pore architecture and surface chemistry. In physical activation, the material is first carbonized under an inert atmosphere and then activated by gasification using steam or CO2 at 800–1100 °C, generating porosity through controlled burnoff; the resulting pore network depends on the activating gas and operating conditions. Among various studies, Yang et al. prepared AC from corn straw using a modified H3PO4 activation approach. Briefly, 10 g of corn straw was soaked in 120 mL of H3PO4, mixed for 30 min, sonicated for 1 h, and then dried at 105 °C overnight. The treated and untreated materials were subsequently pyrolyzed at 300 °C for 2 h under a nitrogen atmosphere, using a heating rate of 5 °C/min. After carbonization, the product was thoroughly washed, dried at 65 °C, and processed by grinding and sieving (60 mesh). The final AC showed a specific surface area of 463.89 m2/g and a pore volume of 0.387 cm3/g, confirming the formation of a more porous structure. In contrast, Wang et al. produced AC from semicoke using KOH as the activating agent. The semicoke was mixed with KOH at mass ratios from 1:0 to 1:3 and then activated under a nitrogen atmosphere at 773–1173 K. The resulting AC reached a specific surface area of 1365.79 m2/g and a pore volume of 0.38 cm3/g, reflecting substantial pore development. The method is relatively economical and can deliver strong adsorption performance; however, it requires high activation temperatures, and the adsorbent may lose efficiency after multiple regeneration cycles. In a similar approach, Islam et al. prepared a KOH-activated carbon (KOH–AC) from palm leaf biomass for TC adsorption. The raw biomass was first washed and milled, then sieved to obtain particles of about 125 μm. For activation, the material was soaked in 1 M KOH and subjected to ultrasonic treatment for 4 h to promote impregnation. The KOH-treated precursor was then carbonized at 800 °C under a nitrogen atmosphere (16 mL/min), using a heating rate of 10 °C/min. After carbonization, the solid was washed stepwise with 20% ethanol, 1 M HCl, and deionized water, and finally dried at 80 °C. The resulting AC showed a specific surface area of 540 m2/g and a pore volume of 0.261 cm3/g, suggesting that KOH activation produced a well-developed porous structure. The general AC preparation routes discussed above are schematically presented in Figure , and additional biomass-based AC studies for TC removal are compiled in Table . Biomass precursors and chemical activation for AC production (created in BioRender). BC Synthesis BC is a carbon-rich material commonly produced by pyrolysis of biomass under oxygen-limited conditions, typically at 300–700 °C. Interest in BC has increased because it can support sustainable agriculture, contribute to carbon storage, and serve as a low-cost material for environmental cleanup. During pyrolysis, the main biomass componentscellulose, hemicellulose, and ligninbreak down through a series of overlapping reactions (e.g., dehydration and depolymerization followed by cracking, aromatization, and condensation). These steps gradually convert the feedstock into a more aromatic, porous, and chemically stable carbon matrix. Before pyrolysis, biomass feedstocks possess inherent oxygen-containing functional groups derived from their main lignocellulosic constituents. Specifically, cellulose is mainly enriched with hydroxyl (−OH) and C–O groups, hemicellulose contains carbonyl (CO) functionalities, and lignin contains an abundance of methoxyl (−O–CH3), ether (C–O–C), and aromatic CC groups. With increasing pyrolysis temperature, the H/C and O/C atomic ratios decrease. The properties of BC depend strongly on operating conditions and the type of biomass used. Parameters such as temperature, heating rate, residence time, and feedstock composition control pore development and surface chemistry, which in turn affect specific surface area, pore structure, and the abundance of surface functional groups. In particular, major structural changes in the 200–600 °C range are often associated with the onset of char formation and the development of a more carbon-rich framework. Besides conventional pyrolysis, other thermochemical routes, such as gasification, hydrothermal carbonization, torrefaction, and flash carbonization, are also used to suit different feedstocks and moisture levels. The hydrothermal approach is schematically shown in Figure , and recent reports on BC preparation conditions and resulting properties are compiled in Table . Biomass feedstocks and hydrothermal processing method for BC production (Created in BioRender). The properties of BC depend strongly on how it is prepared, and this is clear from reported synthesis studies. For instance, Xiang et al. produced wheat-stalk BC and then improved it through physical processing. The feedstock was washed and dried, cut into ∼1 cm pieces, and pyrolyzed at 300, 450, and 600 °C for 4 h under nitrogen. The char was washed, dried at 105 °C, and sieved. It was then ball-milled at 300 rpm for 12 h, using a biochar-to-ball mass ratio of 1:100. Among the tested samples, the best material reached a specific surface area of 257.50 m2/g and a pore volume of 0.1966 cm3/g, showing that higher pyrolysis temperature combined with ball milling can substantially improve surface development. Likewise, Shao et al. prepared BC from cow dung using both one-step and two-step pyrolysis routes. In the single-step approach, the material was heated to 900 °C under nitrogen to obtain a BC with improved structural features. The two-step method used sequential heating with controlled holding periods, either 700 °C followed by 900 °C or the reverse order (900 → 700 °C). The BCs produced by these routes showed improved performance for TC adsorption. For example, Miao et al. produced phosphoric-acid-activated BC from peanut shells (PS) by varying the PS/H3PO4 mass ratio from 1:1 to 1:4. The shells were washed, dried, and sieved before impregnation with H3PO4. After ultrasonication, the material was dried at 150 °C and then pyrolyzed at 800 °C for 2 h under nitrogen. Under the optimized condition, the resulting BC reached a specific surface area of 1753 m2/g with a pore volume of 1.2972 cm3/g, demonstrating the strong pore-forming effect of H3PO4 activation. In a similar manner, Qin et al. prepared KOH-activated BC using rape straw. The precursor was ground and passed through a 200-mesh sieve and first pyrolyzed at 700 °C for 2 h under argon. The obtained BC was then blended with KOH at mass ratios of 1:1, 1.5:1, and 2:1, followed by sonication, drying at 120 °C, and a second heat treatment at 750 °C for 2 h. After activation, the products were washed with 1 mol/L HNO3 and deionized water and dried at 80 °C. The best-performing sample showed a specific surface area of 1531 m2/g and a pore volume of 1.0276 cm3/g, confirming effective porosity development through KOH activation. Factors Affecting TC Adsorption Adsorbent performance for TC removal depends on both the material itself and the water matrix in which it is applied. In most studies, the main operating variables are temperature, pH, adsorbent dose, and background constituents such as salts, natural organic matter, or other dissolved compounds. Higher temperature often speeds up diffusion and transport of TC toward the surface, which can increase uptake when mass transfer is a limiting step. pH is equally influential because it controls the charge on the adsorbent surface and the dominant form of TC in solution, thereby shifting electrostatic effects and the strength of surface binding. In real waters, coexisting organics/inorganics, and in some cases microbial activity, can reduce adsorption by competing for sites, blocking pores, or changing local surface conditions. For consistent TC removal, these parameters must be evaluated together rather than in isolation. Influence of Specific Surface Area A larger SSA generally offers more available sites for TC adsorption and improves the contact between the adsorbent and the contaminant. In AC, the pore network usually contains both micropores and mesopores, depending on the raw material and the activation procedure. Micropores mainly account for the high SSA and adsorption capacity, whereas mesopores help TC molecules diffuse into the structure and reach the inner surface more easily. BC, on the other hand, often has an SSA lower than that of AC but still shows good adsorption performance because of its wider pore size distribution and the presence of various surface functional groups. In BC, the SSA is strongly influenced by factors such as pyrolysis temperature and feedstock type, which together control pore development and structural changes during carbonization. In the context of AC, Demiral et al. synthesized H3PO4–AC from peach fruit stones, achieving a maximum SSA of 1399 m2/g at 400 °C with a 3:1 acid-to-precursor ratio. Increasing the activation temperature to 600 °C reduced the SSA due to pore widening, while subsequent HNO3 treatment enhanced mesoporosity by collapsing micropores. Similarly, Jawad et al. reported a substantial increase in SSA from 0.47 to 681.4 m2/g after chemically activating Mangosteen peels. For BC-based adsorbents, Liu et al. reported that increasing the pyrolysis temperature increased the SSA, reaching 214.97 m2/g at 600 °C, and that an additional acid treatment further raised it to 319.80 m2/g. Saghir et al. also observed a strong rise in the SSA of pistachio shell-derived BC, from 15.12 m2/g at 300 °C to 467.8 m2/g at 900 °C, due to better pore development at higher temperatures. These results show that synthesis conditions have a major effect on the SSA of BC, which in turn improves adsorption efficiency. In general, an increase in SSA in carbonaceous adsorbents, whether AC or BC, provides more active sites for TC molecules and supports more effective removal from water. To facilitate comparison and highlight the SSA–performance relationship, Table compiles representative AC and BC adsorbents with their reported textural properties and TC removal metrics. As summarized in Table , KOH-activated BCs exhibit a broad SSA range (132.82–3463.87 m2/g) with corresponding TC uptake from 86.95 to 2242 mg/g, indicating that stronger activation/pyrolysis conditions markedly enhance accessible porosity and adsorption. ACs also show wide variability (10.19–3037 m2/g; q e = 132.94–1235 mg/g), and the data set emphasizes that TC uptake is governed not only by SSA but also by pore architecture and accessibility. For instance, even low SSA can still deliver high q e when pore volume is large (e.g., oily sludge: 2.07 cm3/g) and when surface chemistry provides strong specific interactions with TC. 2Effect of SSA and PV on q e during TC Adsorption by Selected AC and BC Adsorbentsfeedstocksynthesis methodactivating agentpreparation temperature and timeSSA (m2/g)pore volume (cm3/g) q e (mg/g)ref. Biochar Corn strawChemicalKOH500 °C, 2 h132.820.158986.95 Peanut shellChemicalKOH600 °C, 2 h1271.970.653356.19 Rape strawChemicalKOH700 °C, 2 h15311.0276325.07 Walnut shellChemicalKOH900 °C, 1 h1713.870.3607.00 ± 31.87 Furfural residueChemicalKOH800 °C, 1 h3463.87 2.3882242 ± 7.8 Activated Carbon Palm leavesChemicalKOH800 °C5400.261132.94 Oily sludgeChemicalKOH400 °C, 30 min10.19382.07205.1 SemicokeChemicalKOH800 °C, 3 h1365.790.38302.99 Forsythia Fructus residueChemicalKOH800 °C, 1 h1625.620.78754.66 Natural rock asphaltChemicalKOH800 °C, 2 h30372.1221235 Effect of SSA and PV on q e during TC Adsorption by Selected AC and BC Adsorbents Impact of pH The adsorption of TC on carbon-based adsorbents is strongly affected by the solution pH because it changes both the speciation of TC and the surface charge of the adsorbent. TC behaves as an amphoteric compound with three dissociation constants (pK a1 ≈ 3.4, pK a2 ≈ 7.7, and pK a3 ≈ 9.7), and its ionic form therefore varies with solution pH. At pH < 3.4, TC mainly exists as the cationic species (H4TC+); between pH 3.4 and 7.7, it occurs primarily as H3TC; between pH 7.7 and 9.7, it appears as H2TC–; and at pH > 9.7, it is mainly present as HTC2–. When the solution pH is below the pHpzc, the adsorbent surface is positively charged; at pH values above the pHpzc, the surface becomes negatively charged. Above pHpzc, the pH response is governed by surface functional groups. Native AC/BC typically contains −OH/phenolic, −COOH/–COO–, >CO, and C–O groups, whose protonation–deprotonation determines surface charge and hydrogen-bonding capacity. During carbonization, these oxygen-containing groups transform significantly, while activation introduces new functionalities such as C–O–P moieties from H3PO4 activation and redistributed oxygenated sites from KOH activation followed by acid washing. Further modifications, including oxidation and N-functionalization, introduce additional −COOH/–OH and N-containing sites. This directly affects electrostatic interactions with the different TC species. At low pH, both TC and the adsorbent surface are positively charged, which leads to electrostatic repulsion and lower adsorption. Around neutral pH, TC is mainly in its zwitterionic form and the surface charge of the adsorbent is weaker or mixed, so electrostatic repulsion is reduced and adsorption often increases due to hydrogen bonding, π–π interactions, and other nonelectrostatic forces. The Henderson–Hasselbalch equation can be used to estimate the distribution of TC species at different pH values and, together with the pHpzc of the adsorbent, to relate speciation to adsorption trends. At alkaline pH, TC is mainly anionic, and the negatively charged surface tends to repel it, which lowers electrostatic adsorption; however, surface functional groups and secondary interactions can still support some uptake. In addition, metal ions such as Cu2+ can modify TC adsorption by forming TC–metal complexes under different pH conditions, which may either promote or reduce adsorption depending on the chemistry of the system. The pH-dependent nature of TC adsorption has been confirmed by various studies investigating different adsorbent systems. For instance, Cai et al. found that ZnCl2-modified material (ZBAC) showed a gradual decline in TC removal efficiency as pH increased, which was mainly attributed to the deactivation of functional groups and the emergence of electrostatic repulsion once the solution pH surpassed the pHpzc of 8.3. Similarly, Ninh et al. found that Soybean curd residue-derived carbon (pHpzc = 7.01) maintained stable TC removal across a wide pH range, suggesting dominance of non-electrostatic interactions. Xiang et al. studied wheat stalk BC and found that TC adsorption was highest near neutral pH, where zwitterionic TC interacts more easily with the surface because electrostatic repulsion is low. At higher pH, adsorption decreased due to repulsion between anionic TC and the negatively charged BC surface. Shao et al. worked with cow dung-derived BCs (pHpzc 8.25–8.64) and observed maximum TC removal (∼88–93%) at pH 3.0. In this case, the expected electrostatic repulsion was offset by strong π–π interactions and hydrogen bonding. Adsorption was almost unchanged from pH 4 to 9, but dropped sharply above pH 9. Li et al. showed that surface modification can change the pH response. For KHCO3– modified tea waste BC (pHpzc = 9.23), the adsorption capacity decreased with increasing pH. At pH 7, it still reached 101.44 mg/g, indicating that nonelectrostatic interactions make an important contribution even near or above the pHpzc. Determination and Significance of pHpzc The pHpzc represents the pH at which the adsorbent surface has no net charge and plays a key role in determining electrostatic interactions during adsorption. The pHpzc is commonly determined using the pH drift method, where a series of inert electrolyte solutions (e.g., 0.01 M NaCl) are adjusted to different initial pH values. A fixed amount of adsorbent is added to each solution, and after equilibrium, the final pH is measured. The pHpzc corresponds to the point where the initial and final pH values are equal. Another frequently reported technique is ζ-potential measurement, where the surface electrokinetic potential is measured as a function of pH. The pHpzc is strongly influenced by the balance of acidic and basic surface functional groups such as −COOH, phenolic −OH, carbonyl (>CO), and nitrogen-containing moieties introduced during activation or modification. Thermal treatment, chemical activation, and postmodification alter the abundance and strength of these functional groups, thereby shifting the pHpzc. Effect of Dosage Adsorbent dosage strongly affects how much TC can be removed from water, because it controls the availability of active adsorption sites. At low dosages, there are not enough sites, so TC removal is often incomplete. As the dosage increases, removal usually improves because more surface area and pores are available. However, after a certain point, adding more adsorbent can cause active site overlap and lower the adsorption capacity per unit mass. It is therefore important to find an optimum dosage that gives good TC removal without unnecessary material use. This optimization depends on the properties of the adsorbent, the solution conditions, and the initial TC concentration. Several studies have reported the effect of adsorbent dosage on TC removal using AC and BC. Sayğılı and Güzel tested tomato waste-based AC by changing the dosage from 10 to 50 mg in 50 mL of a 100 mg/L TC solution at 298 K, natural pH, and 1 h contact time. As the dosage increased, the adsorption capacity decreased from 92.5 to 73.7 mg/g, which they related to the aggregation of particles and the overlap of active sites. Based on these results, 50 mg was chosen as the working dosage for further experiments. For BC-based materials, Zhang et al. studied pristine and ball-milled BC prepared from crayfish shells. When the BC dosage increased from 10 to 100 mg, the adsorption capacity dropped from 110.1 to 25.6 mg/g for pristine BC and from 122.6 to 35.2 mg/g for ball-milled BC, mainly because fewer TC molecules were available per unit mass at higher dosages. In contrast, the overall removal efficiency increased from 27.5 to 64.1% for pristine BC and from 30.7 to 88.0% for ball-milled BC. The higher removal in the ball-milled sample was ascribed to its larger SSA and better exposure and dispersion of active sites, which supported more effective TC adsorption. Effect of Initial TC Concentration The initial concentration of TC in solution is an important factor that controls how carbon-based adsorbents perform. It directly affects the concentration gradient that drives the TC from the bulk solution to the adsorbent surface. At low TC concentrations, there are many free active sites compared with the number of TC molecules, so the removal efficiency is usually high. As the concentration increases, these sites gradually become occupied and the removal efficiency starts to fall. In contrast, the adsorption capacity often increases with increasing TC concentration because the stronger driving force for diffusion promotes uptake until a plateau is reached when the adsorbent is saturated. This behavior is seen not only for AC but also for BC, especially for materials with well-developed pores and abundant surface functional groups. At very high TC concentrations, competition for sites and limited access to inner pores can slow mass transfer and reduce overall efficiency. Understanding the role of the initial TC concentration is therefore important for optimizing adsorption systems, interpreting adsorption isotherms, and designing TC removal processes for water treatment. Several studies have examined how the starting TC concentration affects the removal by different ACs. Nayak et al. investigated the effect of the initial tetracycline concentration on adsorption by activated carbon by varying the concentration from 100 to 1000 mg/L at a fixed adsorbent dose of 1.25 g/L. They reported that the adsorption percentage decreased as the initial antibiotic concentration increased. Ghorbanian et al. observed a similar trend for AC prepared from hard pistachio shells: as the initial TC concentration increased from 10 to 50 mg/L, the removal efficiency decreased from 68.6 to 30.2%. Similar trends have been reported for BC-based adsorbents. Naghipour et al. studied TC removal using 1 g of BC at pH 5.1 with initial concentrations from 50 to 500 mg/L. As the concentration increased, removal efficiency decreased, but the adsorption capacity rose from 62.5 to 75.6 mg/g, meaning that although the percentage removal fell, more TC was taken up per gram of BC. Zhao et al. examined TC adsorption on BCs prepared at different temperatures. When the initial TC concentration increased from 50 to 500 mg/L, the adsorption capacity of 450-B increased from 4.24 to 11.30 mg/g, and that of 650-K from 91.82 to 173.61 mg/g. At higher concentrations, the increase in capacity became smaller, showing gradual saturation of adsorption sites and a near-plateau in uptake. Effect of Contact Time Contact time is the period during which TC molecules remain in contact with the adsorbent surface and has a direct effect on adsorption. In most cases, adsorption occurs in two steps: a fast initial stage, when many active sites are available, followed by a slower stage as these sites become filled. The drop-in rate at the later stage is usually linked to pore diffusion limits or surface saturation. The time required to reach adsorption equilibrium depends on the accessibility of active sites and the diffusion of TC molecules within the pore network of the adsorbent. Structural features such as pore architecture and surface properties can therefore influence adsorption/desorption behavior and the overall equilibration process. Liu et al. explored TC adsorption on porous biomass carbon prepared from garlic skin. They reported a very fast uptake within the first 5 min, followed by a slower stage, with equilibrium reached after 24 h. The adsorption capacity was 1588.9 mg/g at an initial TC concentration of 400 mg/L and increased to 1911.8 mg/g at 800 mg/L, showing the strong affinity of this material for TC. Ninh et al. investigated mesoporous AC from soybean curd residue and found that about 80% of TC was removed within the first 30 min; adsorption then continued beyond 180 min, indicating that, in the later stage, the process was mainly controlled by diffusion of TC into the mesopores. Saremi et al. examined vitamin B6-modified BC and observed a rapid rise in adsorption capacity to 54.9 mg/g within 10 min, after which the uptake curve flattened, indicating quick attainment of equilibrium. Together, these results show how contact time, pore structure, and surface modification govern both the rate and extent of TC adsorption. Influence of Temperature Temperature has a strong effect on TC adsorption onto carbon-based materials because it changes diffusion rates, surface interactions, and the properties of the adsorbent itself. In many cases, increasing the temperature raises the adsorption capacity, as higher thermal energy promotes molecular motion, speeds up intraparticle diffusion, and helps activate surface sites, which is consistent with an endothermic process. In other systems, adsorption behaves exothermically, especially when it is mainly physisorption or when strong adsorbate–adsorbent interactions release more energy than is needed to desolvate TC. Under those conditions, higher temperatures can lower adsorption efficiency. Thermodynamic parameters such as Gibbs free energy (ΔG 0), enthalpy (ΔH 0), and entropy (ΔS 0) are used to assess whether adsorption is spontaneous and to understand the heat effects involved. Carrying out experiments at different temperatures is therefore important for identifying the adsorption mechanism and selecting suitable operating conditions for TC removal. Marzbali et al. observed a significant rise in the distribution coefficient (K d) from 5.34 to 34.69 as temperature increased from 308.15 to 338.15 K, due to the expansion of active sites. Thermodynamic analysis revealed an endothermic process (ΔH° = 54.02 kJ/mol) with increased disorder (ΔS° = 189.51 J/mol·K). Negative ΔG° values (−4.29 to −9.96 kJ/mol) indicated spontaneous adsorption that became more favorable at higher temperatures, likely driven by chemical interactions such as hydrogen bonding and protonation. Naghipour et al. found that TC removal efficiency increased from 10 to 50 °C. Thermodynamic data from Van’t Hoff plots showed an endothermic process with ΔH° = 38.74 kJ/mol and ΔS° = 137.09 J/(mol K). ΔG° values became increasingly negative (−0.78 to −6.28 kJ/mol) with rising temperature, confirming enhanced spontaneity. Effect of Coexisting Ions on Adsorption The ions present in natural waters and wastewaters can strongly affect TC adsorption. Divalent cations such as Ca2+ and Mg2+ often reduce adsorption capacity by forming soluble complexes with TC or by occupying surface sites, whereas monovalent ions like Na+ and K+ usually interact more weakly and cause only limited interference. Common anions (NO3 –, SO4 2–, PO4 3–) can also influence adsorption by changing the ionic strength of the solution and thus the electrostatic forces between TC and the adsorbent. Kim et al. studied the effect of coexisting ions on TC adsorption using coconut shell-based powdered AC and its thermally treated form at 800 °C. They reported that thermal treatment modified the surface functional groups and shifted the surface charge of the carbon, making it more positively charged under the experimental pH; this enhanced electrostatic attraction with the ionized TC species led to higher adsorption efficiency. BC-based adsorbents often show stronger sensitivity to ionic strength. Ma et al. examined furfural residue BCs produced at 300 and 600 °C and found that, as Na+ concentration increased from 0 to 0.1 mol/L, TC adsorption decreased from 5887 to 2415 mg/kg and from 9584 to 7565 mg/kg, respectively. Divalent cations (Ca2+ and Mg2+) at 0.02 mol/L suppressed adsorption even more than Na+, with Ca2+ causing about 48% greater reduction in TC uptake compared with Na+. Adsorption Models for TC Uptake Understanding the kinetics and equilibrium behavior of TC adsorption on carbon-based adsorbents is important for designing practical water treatment systems. The main kinetic and isotherm models used for TC adsorption are summarized in Table . Kinetic models such as the pseudo-first-order (PFO) and pseudo-second-order (PSO) are commonly applied to describe how fast adsorption occurs and to infer the controlling mechanism. The PFO model is usually associated with physical adsorption driven by weak van der Waals forces, whereas the PSO model is more consistent with chemisorption involving electron transfer or sharing with surface groups such as −OH, −COOH, and CO. The Elovich model is often used for chemisorption on heterogeneous surfaces with a wide range of activation energies, and the intraparticle diffusion (IPD) model helps to identify diffusion-controlled steps and boundary layer effects. In addition, the two-compartment first-order model describes adsorption as a two-stage process, with a fast initial step followed by a slower stage, providing a more detailed view of multistage adsorption behavior. 3Various Kinetic, Isotherm, and Thermodynamic Models Applied in TC Adsorptionmodelmodel equationparameters and constants Kinetic Models Pseudo-first-order (PFO) qt=qe(1−exp(−K1t)) q t: adsorption capacity at time t (mg/g) q e: adsorption capacity at equilibrium (mg/g) t: contact time (min) K t: rate constant of the PFO (min–1)Pseudo-second order (PSO) qt=qe2K2tqeK2t+1 K 2: rate constant of the PSO(g.mg–1 min–1)Intraparticle Diffusion qt=Kt0.5+C K: rate constant of IPD (mg g–1 min0.5) C, intercept constant (mg/g)Elovich qt=1βln(αβ)+1βln⁡t β: desorption constant (g/mg)α: initial adsorption rate (mg/g·min) Isotherm Models Langmuir qe=qmaxbCe(1+bCe) q max: maximum adsorption capacity (mg/g) b: Langmuir constant (L/mg)Freundlich qe=KFCe1/n K F: Freundlich constant ((mg/g)/(mg/L)1/n ) C e: equilibrium concentration (mg/L) n: Freundlich exponent (dimensionless)Dubinin–Radushkevich qe=qmax⁡exp(−βε2) β: sorption energy constant (mol2/kJ2)ε: Polanyi potential (J/mol) Thermodynamic Models Van’t Hoff Equation KT=exp[(ΔS°R)−(ΔH°R)1T] K T: distribution factor (L/mg)ΔS°: standard entropy (J/mol K)ΔH°: standard enthalpy (kJ/mol) R: ideal gas constant (J/mol K) T: Absolute Temperature (K) Various Kinetic, Isotherm, and Thermodynamic Models Applied in TC Adsorption Adsorption equilibrium is usually described using different isotherm models. The Langmuir model assumes monolayer adsorption on a uniform surface, whereas the Freundlich model describes multilayer adsorption on heterogeneous surfaces. The Temkin model takes into account interactions between the adsorbate and adsorbent by assuming that the adsorption energy decreases linearly with coverage. The Dubinin–Radushkevich (D–R) model is used to distinguish between physical and chemical adsorption based on the mean adsorption energy and is also helpful for analyzing pore-filling processes. Using these models together helps to clarify the adsorption mechanism and to design AC- and BC-based systems for TC removal. Zhao et al. studied TC adsorption on granular AC using several kinetic models. Among them, the two-compartment first-order model gave the best fit to the data (R 2 = 0.9599). This model describes a two-step process with a fast initial uptake followed by a slower stage controlled by stronger chemisorption. In other words, TC is adsorbed quickly at first, and then a slower but more strongly bound fraction develops over time. The IPD model also indicated that adsorption occurs in more than one step, as the plots did not pass through the origin, showing the role of surface resistance and boundary layer effects. For the equilibrium data, the Temkin isotherm gave a good fit (R 2 = 0.8949), suggesting that interactions between TC and the AC surface, such as electrostatic attraction or ion exchange, play an important role in the adsorption process. Islam et al. studied TC adsorption on KOH-activated AC prepared from palm leaves. Kinetic data were best described by the PSO model, with a high correlation coefficient (R 2 = 0.970) and good agreement between experimental (q e,exp = 94.00 mg/g) and calculated (q e,cal = 96.75 mg/g) capacities, suggesting that the process is mainly chemisorption. For equilibrium, the adsorption data were well fitted by the Langmuir model (R 2 = 0.947), indicating monolayer coverage on a relatively uniform surface, with a maximum capacity (q m) of 132.94 mg/g at 25 °C. The Temkin model also showed a similar R 2 value (0.946), supporting the conclusion that the adsorption is endothermic. A comparative summary of ACs from different biomass sources is given in Table . 4Comparative Synthesis Methods and Adsorption Performance of Biomass-Derived AC for TC Removal, Including Isotherm and Kinetic Model Analysisfeedstocksynthesis methodactivating AgentSSA (m2/g)removal (%) q max (mg/g)isotherm modelkinetic modelthermodynamic natureref. Thysanolaena maxima ChemicalKOH1065.0119721.317LangmuirPseudo-second-orderEndothermic Commercial AC (Copper sulfate-impregnated) ChemicalCu533.534.12LangmuirExothermic Palm leaves ChemicalKOH54088.18132.94LangmuirPseudo-second-orderEndothermic Corn Straw ChemicalH3PO4 463.8998227.3LangmuirPseudo-second-orderEndothermic Waste plastics ChemicalKOH, NaCl1006.31100242.46LangmuirPseudo-second-orderEndothermic Semicoke ChemicalKOH1365.79315.12LangmuirPseudo-second-order Sawdust ChemicalP2O5 1579523.63LangmuirPseudo-second-orderEndothermic Wheat Dust ChemicalNaOH2821.581414.65FreundlichPseudo-second-orderEndothermic Straw ChemicalK2CO3 158090615LangmuirPseudo-second-orderEndothermic Comparative Synthesis Methods and Adsorption Performance of Biomass-Derived AC for TC Removal, Including Isotherm and Kinetic Model Analysis Extending the understanding of BC systems, Shi et al. studied TC adsorption on walnut shell-derived BC using kinetic, isotherm, and diffusion models. Among the kinetic models, the PSO model fitted the data better than the PFO model, indicating that chemisorption is the main rate-controlling step. The IPD and film diffusion models showed that adsorption proceeded in several stages. To analyze equilibrium behavior, the data were fitted to both Langmuir and Freundlich isotherms. The Langmuir model gave the better fit (R 2 = 0.95), suggesting monolayer adsorption on a relatively uniform surface with a finite number of identical sites. Lin et al. examined TC adsorption on BC derived from Schizochytrium limacinum. The kinetics followed the PSO model (R 2 = 0.99), again pointing to chemisorption. In this case, the Freundlich isotherm described the equilibrium data more accurately (R 2 = 0.96), while the Langmuir model estimated a high monolayer capacity of 1357.5 mg/g, indicating strong adsorption potential for TC removal. A broader comparison of BC adsorbents and their performance is given in Table . 5BC Adsorbents from Various Biomass Precursors with Key Synthesis Details and TC Adsorption Parameters feedstocksynthesis methodactivating AgentSSA (m2/g)removal (%) q max (mg/g)isotherm modelkinetic modelthermodynamic natureref. Wheat stalk PhysicalN2 257.5075.95LangmuirPseudo-second-order Cow dung PhysicalN2 238.9398.96158.9322LangmuirPseudo-second-order Pinus taeda ChemicalNaOH959.9274.8FreundlichElovichExothermic Tea waste ChemicalKHCO3 1981293.46FreundlichPseudo-second-order Alfalfa ChemicalNaOH796.50 302.37 LangmuirPseudo-second-order Rape straw ChemicalKOH153197325.07FreundlichPseudo-second-orderEndothermic Peanut shell ChemicalH3PO4 1753570.73 Langmuir and TemkinElovich Walnut shell ChemicalKOH1713.87>95%607.00LangmuirPseudo-second-orderEndothermic Corn starch Physical and ChemicalZnCl2 16451001122.2FreundlichPseudo-second-orderEndothermic Schizochytrium limacinum (microalgae) ChemicalKHCO3 2295.261357.5FreundlichPseudo-second-order a“Physical” = thermal/pyrolysis without chemical activators; “chemical” = activation/modification with chemical agents (e.g., KOH, ZnCl2, H3PO4, metal salts). BC Adsorbents from Various Biomass Precursors with Key Synthesis Details and TC Adsorption Parameters “Physical” = thermal/pyrolysis without chemical activators; “chemical” = activation/modification with chemical agents (e.g., KOH, ZnCl2, H3PO4, metal salts). Adsorption Mechanism of TC TC adsorption on carbon-based materials takes place through several physical and chemical interactions, such as π–π stacking, hydrogen bonding, electrostatic attraction or repulsion, hydrophobic effects, van der Waals forces, and pore filling (Figure ). The dominance of these interactions depends on the surface chemistry, pore structure, and functional groups of the adsorbent, as well as solution conditions like pH and ionic strength. Adsorption mechanisms of TC onto carbonaceous adsorbents (TC structure created using Avogadro 1.2.0; other elements designed in BioRender). π–π Interaction The dominant mechanism of TC adsorption depends on the properties of the adsorbent and on conditions such as pH and ionic strength. For many carbon-based materials, π–π interactions, especially π–π electron donor–acceptor (EDA) interactions, play a key role. TC has conjugated aromatic rings that can stack face-to-face or edge-to-face with π-rich carbon surfaces. These interactions are stronger when the carbon is more graphitized, carries surface groups such as −OH and −COOH, and the pH is near neutral, which helps maintain the planar structure of TC. In doped carbons, partial charge transfer in π–π EDA interactions further increases adsorption. Ding et al. studied TC adsorption on carbon materials and emphasized the importance of π–π EDA interactions, especially in 2D carbon adsorbents. Polarized graphite provides electron-rich regions as active sites, while the carbonyl-rich conjugated ketene structure of TC behaves as an electron acceptor. This pairing promotes strong π–π EDA interactions and leads to high TC uptake. Hydrogen Bonding Hydrogen bonding is one of the main pathways for TC adsorption. It occurs between the polar functional groups of TC (−OH, −NH2, −CO) and oxygen-containing groups (−OH, −COOH) on the adsorbent surface. These groups can act as hydrogen bond donors or acceptors, helping TC molecules attach and stay on the surface, which increases adsorption capacity. The strength of hydrogen bonding depends on factors such as SSA, pore structure, and the amount of surface functional groups, and it is usually favored at neutral to slightly alkaline pH. Hydrogen bonding often works together with π–π stacking and electrostatic interactions to improve TC removal. For example, Li et al. studied TC adsorption on lignin-derived hierarchical porous carbon (LPHC) and showed that the abundant oxygen-containing surface groups (CO, C–O, −OH) on LPHC formed hydrogen bonds with the −OH and −CO functionalities of TC. Spectroscopic evidence (changes in the intensity and position of O–H/N–H and CO/C–O bands) indicated that these hydrogen-bonding interactions were a major contributor to TC uptake. Electrostatic Interactions Electrostatic interactions are an important factor in TC adsorption because TC is amphoteric and can exist in cationic, zwitterionic, or anionic forms depending on pH. At low pH (≤3), both TC and many adsorbents are positively charged, so electrostatic repulsion reduces adsorption. Between pH 3–6, TC is mainly zwitterionic, which can favor adsorption on weakly charged surfaces. At higher pH (≥8), TC is mainly anionic and can be strongly attracted to positively charged adsorbents. He et al. showed that electrostatic attraction near pH 6 greatly enhanced TC adsorption, whereas repulsion at acidic and highly alkaline pH reduced uptake. Liu et al. also found that, under alkaline conditions, electrostatic interactions were the main contributor to TC adsorption on grape leaf-based BC prepared at 900 °C, with changes in surface charge and TC speciation strongly controlling removal performance. Surface Complexation Carbon materials contain many oxygen-containing functional groups (−OH, −COOH, −CO) that can interact with the polar groups of TC (−OH, −NH2, >CO) through ligand exchange or coordination, especially at neutral to slightly acidic pH, where TC is mainly in its zwitterionic form. Under these conditions, inner-sphere complexes can form by direct bonding between TC and surface groups, which contributes strongly to chemisorption and improves adsorption capacity, selectivity, and stability, while outer-sphere complexes based on electrostatic attraction play a smaller role. As shown in Figure , this pH dependence helps explain the generally better performance near neutral pH. In line with this, Ngoc et al. reported that hydrochar-derived ACs prepared from glucose solution by hydrothermal treatment and from ZnCl2-activated teak sawdust hydrochar showed enhanced TC adsorption due to their higher content of oxygenated surface groups, which favored inner-sphere complex formation and efficient TC uptake near neutral pH. Recent Advances in TC Removal Recent advances in TC removal have focused on tailoring the physicochemical properties of carbon-based adsorbents to boost their adsorption efficiency. Key strategies include surface chemistry modifications to introduce active functional groups, pore size engineering to optimize accessibility and diffusion of TC molecules, and the development of multifunctional composites that enhance structural properties and reusability. These approaches have collectively contributed to significant improvements in adsorption performance and offer valuable insights for designing next-generation adsorbents. The following sections elaborate on each of these strategies in detail. Surface Chemistry Modifications Surface modification of carbon-based adsorbents by oxidation, amination, or metal oxide loading can improve TC adsorption by introducing functional groups such as −OH, −COOH, −NH2, and PO4 3–. These groups increase active site density, tune surface charge, and strengthen hydrogen bonding, π–π stacking, and electrostatic interactions in water. For example, Quyen et al. prepared a magnetic AC/Fe3O4 composite from rice husk ash. The AC was first treated to remove silica and then acid-activated, which enriched the surface with oxygen-containing groups, especially −COO–. These groups then coordinated with Fe2+ and Fe3+ during coprecipitation, leading to uniform Fe3O4 deposition. The modified surface promoted electrostatic and complexation interactions with TC, and the Fe3O4 phase allowed easy magnetic separation of the adsorbent from solution. In a related BC system, Wu et al. synthesized ammonium persulfate (APS)-activated chitosan biochar (APS@CHI) using ammonium persulfate as an oxidizing agent. APS treatment introduced additional oxygen-containing groups (CO, −COOH) and nitrogen functionalities (pyrrolic N-5 and pyridinic N-6) through oxidation and heteroatom doping. These changes increased surface reactivity and electron-donating capacity, improved TC binding (as illustrated in Figure ), and, together with the high SSA and functional group density, made the material a strong candidate for antibiotic removal. Schematic representation of surface functionalization in BC and AC for enhanced adsorption (Created using Avogadro 1.2.0). Pore Size Modification The pore size distribution of carbon-based materials strongly affects TC adsorption because TC has relatively large molecular dimensions. To improve access and diffusion of TC molecules, many recent studies have tuned the pore structure either during synthesis or by post-treatment. For AC, Wang et al. prepared 3D porous carbon from glucose and ammonium chloride by pyrolysis at 900 °C under argon, followed by controlled oxidation in air at 350, 400, and 450 °C. The resulting carbons had mainly micropores with an average pore size of about 2.5 nm, which is suitable for TC adsorption. Similar pore engineering in BC has also been effective. Du et al. used keratin-rich bovine horn as a precursor, first thermally pretreated it at 160–200 °C and then activated it with KOH at 900 °C. The pretreatment temperature strongly affected the final structure and porosity. The sample pretreated at 180 °C showed the best properties, with an ultrahigh SSA (2806 m2/g), a larger average pore diameter (2.68 nm), and a well-developed mesoporous structure. These features were linked to partial oxidation of disulfide bonds to sulfonic/sulfone groups and an increase in β-sheet content, which helped maintain structural integrity during activation. Composite Materials for Enhanced TC Adsorption Recent work on TC removal has focused on engineered carbon materials combined with functional additives. For example, Fe2O3-loaded carbon prepared from rubber fig leaves showed higher TC adsorption because of the combined effect of its large SSA and magnetic properties. A multifunctional composite made by combining AC from Camellia oleifera shells with a magnetic MnO2/MCM-41@Fe3O4 phase, encapsulated in alginate and calcium chloride, also showed improved TC removal, mainly due to its mesoporous structure, high SSA, and easy magnetic separation. Similar progress has been made with BC-based composites. A BC-ceramsite material produced from pine sawdust, fly ash, red mud, and MgO by staged anoxic sintering achieved good TC removal through its porous structure and mineral-assisted adsorption. In another study, nitrogen-doped porous BC derived from ZIF-67 grown on polydopamine-coated loofah exhibited high TC uptake, attributed to its hierarchical pores and cobalt-based active sites. Future Scope and Perspectives The continuous presence of TC and other antibiotics in water bodies is now recognized as a serious risk for both the environment and public health. Among the different treatment options, carbon-based materials such as AC and BC have attracted a lot of attention as adsorbents. They are mainly preferred because of their high specific surface area, adjustable pore structure, and rich surface functional groups, which together make them suitable for the selective removal of TC. Despite these advantages, some issues still limit their large-scale use. A major problem is the complex and often inconsistent synthesis of AC and BC. It is difficult to obtain materials with uniform morphology, stable surface chemistry, and reproducible properties from batch to batch, particularly when chemical modification or composite formation is involved. Therefore, future work should focus on greener, scalable, and low-cost preparation routes based on optimized pyrolysis and hydrothermal carbonization. In particular, efforts should prioritize scaling these processes in continuous or semicontinuous reactors and improving energy integration. Coupling production with locally available biomass residues can help to obtain carbon materials with more uniform properties at lower cost and with a reduced overall environmental burden. Another important research need is to evaluate the long-term behavior and reusability of these materials under more realistic conditions. Most available studies are carried out in controlled laboratory systems and do not fully reflect variations in pH, the presence of coexisting ions, natural organic matter, or microbial activity in real wastewater. More detailed investigations on the stability of AC and BC over repeated adsorption–desorption cycles, as well as on the possible leaching of incorporated metal species, are required to confirm their environmental safety and sustained adsorption performance. In addition to plain carbon materials, hybrid adsorbents based on AC or BC combined with metal oxides or doped with heteroatoms are also being explored. These modified carbons often show higher removal efficiency because of combined effects, such as stronger adsorption affinity and higher surface reactivity. Such multifunctional materials may be useful in future treatment systems dealing with complex mixtures of pollutants. To move from lab studies to practical use, future work should include techno-economic analysis, life-cycle assessment, and pilot-scale trials in different types of wastewaters. In the long run, developing AC- and BC-based adsorbents that are selective, easy to regenerate, and environmentally safe will be important for the sustainable removal of TC from contaminated water. Conclusion This review shows that biomass-based AC and BC can play an important role in removing TC from water. They are relatively low-cost, can be tuned through surface modification, and are often produced by routes that are more environmentally friendly than many synthetic adsorbents. The removal of TC mainly depends on interactions such as π–π stacking, hydrogen bonding, and surface complexation. The way AC and BC are synthesized and activated strongly affects their surface area, pore structure, and functional groups, and therefore their adsorption behavior. In addition, solution conditions such as pH, ionic strength, and temperature change both the surface properties of the adsorbent and the speciation of TC, which together control the overall uptake. Surface functionalization, for example, by chemical doping or introducing heteroatoms, has been shown to improve selectivity and make regeneration more feasible. Although many lab-scale studies report promising results, several gaps remain, especially in tests with real wastewater, regeneration over many cycles, and long-term stability. Future work should focus on pilot-scale studies, life-cycle assessment, and ways to integrate these materials into existing treatment units so that their potential in advanced wastewater treatment can be fully demonstrated.