Semipilot Scale Synthesis of Zeolite A from Kaolin Filler: Process Optimization with Boiler Steam, Mathematical Modeling, and Cu2+ Adsorption Authors: Emerson Cardoso Rodrigues, Camila Santana Dias, Josiel Lobato Ferreira, Bruno Maués Farias, Diego Cardoso Estumano, Bruno Marques Viegas, José Antônio da Silva Souza, Emanuel Negrão Macêdo Published: 2026 ABSTRACT This work reports the semipilot-scale synthesis of zeolite A using a boiler as an unconventional thermal energy source and Amazonian kaolin filler as the Si/Al source. By enabling more effective heat transfer and reducing reaction times without compromising product quality, the proposed method enhances conventional synthesis routes. Zeolite A formation was confirmed by structural characterization using XRD, XRF, TG/DTA, and SEM. Adsorption experiments of Cu2+ ions were conducted at 25, 50, and 75 °C, showing maximum adsorption capacities of 107.5, 124.1, and 119.9 mg g–1, respectively, demonstrating high metal removal performance. Langmuir, Freundlich, and Sips isotherms were used to model the adsorption equilibrium, and parameters were estimated via a Markov chain Monte Carlo method. The Langmuir isotherm provided the best fit at 25 °C, whereas the Sips isotherm showed superior performance at 50 and 75 °C, as indicated by both the coefficient of determination and the Bayesian Information Criterion. The results highlight the potential of this route as a scalable and efficient alternative for zeolite A synthesis, capable of producing high-quality material in a reduced synthesis time and demonstrating effective performance in environmental applications. Introduction The mining sector is one of the main pillars of the Brazilian economy, attracting significant investments. In 2023, investment in this sector exceeded 30 billion Brazilian reais (BRL). In the same year, investments in mineral research reached approximately 2.3 billion BRL. This development is reinforced by the mineral sector’s greater contribution to the Brazilian economy, where total production exceeded 0.26 trillion BRL, and by its significant impact on the labor market, with the creation of approximately 846,600 jobs in the first half of 2022. Regarding kaolin, total production of this mineral in Brazil in 2023 reached around 0.85 billion BRL, with income from the processed product amounting to 811.40 million BRL. The state of Pará stands out as the main producer of this consumer good in the period, with 602,980.43 tons of processed kaolin, compared to more than 800,000 tons produced in the country, generating a total income in the state of about 480 million BRL. The physical and chemical properties and low cost of kaolin enable its use in various industrial segments, such as paints, cosmetics, plastics, and rubber. However, its greatest use is in the paper industry, where it acts as a coating and filling agent, giving the paper surface uniform density and porosity, which are essential for obtaining high-quality prints. − In addition, due to its resistance to pH variations, thermal and hydrothermal stability, molecular selectivity, and presence of exchangeable cations, kaolin has gained prominence as a raw material for the synthesis of zeolites. Zeolites are highly ordered crystalline aluminosilicates widely used as molecular sieves, catalysts, and adsorbents, as well as in cracking, separation, and purification processes. Among them, zeolite A stands out for its commercial use, mainly in water decontamination through the adsorption of metal ions, an application that has shown promising results. − Even though the hydrothermal method is widely used to synthesize zeolite A, the advances documented in the literature are still mostly restricted to laboratory-scale settings and heavily rely on lengthy crystallization times and traditional heating configurations. − There are currently few studies that systematically address the use of alternative thermal sources, process adaptation to larger scales, and synthesis time reduction. Furthermore, not much research examines how these changes affect the process’s operational viability and the final product’s functional performance. Thus, there is a glaring need to develop more effective and scalable synthesis routes to produce zeolite A. The central objective of this study is to evaluate the efficient production of zeolite A at an enlarged scale using filler kaolin via an alternative synthesis route that employs a boiler as the heat source. Unlike conventional laboratory-scale methods, which are often limited by long reaction times and scale-up challenges, the proposed approach significantly reduces synthesis time while maintaining material quality. The synthesis was carried out at a semipilot scale, using a larger-volume closed reactor under controlled temperature and pressure. This demonstrates the practical potential of the method for scale-up and future implementation in more realistic production scenarios. The use of a boiler as a thermal source represents an advancement over traditional routes by providing efficient heating compatible with larger scales, thereby improving the operational feasibility of the process. Furthermore, the application of the synthesized zeolite A for Cu2+ ion adsorption, combined with Bayesian inference via the Markov chain Monte Carlo (MCMC) method to estimate isotherm parameters, integrates synthesis, environmental application, and advanced statistical analysis within a single study, while also allowing quantification of parameter uncertainty, capturing correlations between parameters, and providing a probabilistic framework for model predictions. In this context, the Cu2+ ion was selected as a model contaminant due to its recognized environmental relevance, its association with mining and mineral processing activities, and its widespread use as a reference ion in adsorption studies. This integrated approach reinforces the relevance of the proposed process, particularly in the Amazon region, where mining activities intensify the presence of heavy metals in the environment, and highlights the potential of the developed route as an alternative to conventional zeolite A synthesis methodologies. Materials and Methods Starting Material and Reagents The kaolin filler used as a source of silica and alumina in this investigation comes from the classification stage, which is part of the kaolin beneficiation process, carried out in the city of Barcarena, in the state of Pará, Brazil. Sodium hydroxide (NaOH) was used in the synthesis of the zeolitic material, while copper sulfate pentahydrate (CuSO4.5 H2O) and sulfuric acid (H2SO4) were used in the adsorption experiments. A 5.0 M sodium hydroxide solution was prepared by dissolving analytical-grade NaOH (Casa da Química Industrial e Comércio Ltd.a., Brazil) in distilled water. Similarly, a 1000 ppm copper solution was prepared from analytical-grade copper sulfate pentahydrate (CuSO4·5H2O, Casa da Química Industrial e Comércio Ltd.a., Brazil) using distilled water, while a 1.0 M sulfuric acid solution was obtained by diluting analytical-grade H2SO4 (65–98 wt %, density 1.84 g·cm–3, Casa da Química Industrial e Comércio Ltd.a., Brazil) with distilled water. Synthesis of Zeolite Material Initially, the kaolin filler was calcined at 600 °C for 2 h to remove adsorbed water and impurities, ensuring maximum efficiency in the subsequent adsorption experiments. The synthesis method used to produce the zeolitic product was hydrothermal on a semipilot scale. , The material obtained after calcination was introduced into a stainless-steel reactor with an internal volume of approximately 0.018 m3. A total mass of 4.5 kg of calcined kaolin was charged into the reactor and mixed with a 5 M NaOH solution to adjust the mixture to an Al/Na ratio of 0.57. The hydrothermal synthesis was carried out at a temperature ranging from 110 to 120 °C under a pressure of 1.5 kgf·cm–2. The zeolite synthesis process was maintained for 3 h. The heating system was supplied by steam generated from a boiler (model: VMV 1P 150), with a capacity of 150 kg·h–1, a heating surface area of 6.3 m2, and a diesel oil consumption rate of 11 kg·h–1. After the synthesis period, the reactor was cooled to room temperature, and the suspension was filtered to separate the phases until neutral pH was reached. Following the filtration step, the zeolites were dried in an oven for 24 h at 110 °C. During the synthesis process, aliquots were withdrawn at 30 min intervals to investigate the kinetics of zeolite formation on a semipilot scale. Each collected sample was immediately cooled to room temperature to quench the reaction, followed by filtration to separate the solid phase. The recovered solids were washed with distilled water until neutral pH was reached and subsequently dried prior to further characterization. Figure shows the equipment used for zeolite synthesis. Schematic representation of the reactor system employed for zeolite synthesis. Adsorption Tests The zeolite produced was subjected to a calcination process at a temperature of 400 °C before the adsorption tests were carried out. Batch adsorption tests were performed with a copper sulfate solution at a concentration of 1000 ppm. A 1 M H2SO4 solution was used to adjust the pH. The concentration of copper in the solutions was determined by UV–vis spectrometry at 800 nm. This technique was selected due to its sensitivity for Cu2+ detection and its lack of interference from the sulfate anion present in the aqueous medium. Measurements were performed following standard procedures, ensuring reliable quantification of copper for the adsorption experiments. The calibration curve used for Cu2+ quantification is provided in the Supporting Information. An experimental uncertainty of 1% (expressed as standard deviation) was considered based on the analytical precision of the concentration measurements. Adsorption Kinetics It was used 0.02 g of the synthesized product and added to Erlenmeyer flasks containing 100 mL of a solution with copper ions Cu2+, whose concentrations of this adsorbate were evaluated in each test: 80, 200, 300, 500, and 1000 ppm. The temperature adopted was 25 °C with agitation at 150 cycles/min for 240 min. Adsorption Equilibrium The adsorption equilibrium tests were conducted at temperatures of 25, 50, and 75 °C. For each temperature evaluated, six solutions with different Cu2+ ion concentrations were used (20, 60, 100, 200, 300, 500, and 1000 ppm). These concentrations were selected to represent untreated or highly concentrated industrial effluents and to enable a reliable evaluation of adsorption capacity and equilibrium modeling. The total experiment time was 240 min, with a stirring rate of 150 cycles/min, maintaining the same conditions adopted in the kinetic tests. Table shows the Langmuir, Freundlich, and Sips isotherms − used to verify which would be most suitable for the equilibrium data obtained. 1Most Relevant Parameters and Assumptions of the Isotherms UsedIsothermModelHypothesesParametersLangmuir qe=qmKCe(1+KCe) Monolayer, uniform surface q m and K Freundlich qe=KFCe1/n Multilayered, heterogeneous surface K F and n Sips qe=KSCeβS1+aSCeβS The sites are not energetically homogeneous. a S , K S and β S Most Relevant Parameters and Assumptions of the Isotherms Used In these equations, q e (mg/g) the amount adsorbed at equilibrium, q m (mg/g) the maximum adsorption capacity, K (L/mg) the Langmuir constant, C e (mg/L) the concentration of the solution at equilibrium, K F (L/mg) and n (−) are parameters of the Freundlich isotherm. K S (L/mg) is the sips constant, a S (L/mg) is the affinity coefficient of this isotherm and β S (−) is the heterogeneity coefficient. Estimation of Isothermal Parameters The isotherm parameters adopted in this study were estimated using the Markov Chain Monte Carlo method within a Bayesian framework. This method is based on the random generation of samples from the posterior probability distribution within the parametric space until an equilibrium distribution is reached. This equilibrium indicates the region of highest probability for the estimated parameter values, ensuring that they are statistically adequate to represent the experimental profile with the adopted model. − After the parameter estimation process, the quality of the fit between the isotherms and the experimental data was evaluated using the coefficient of determination (R2) and the Bayesian Information Criterion (BIC), eq . 1 BIC=−2log[p(Y|P)]+Nplog(Nmed) where N p represents the number of parameters to be estimated, N med the number of measurements used. X-ray Diffraction The X-ray diffractometer used was the X’PERT PRO MPD (PW 3040/60) model from PAnalytical, with a PW3050/60 goniometer (Theta/Theta) and a ceramic X-ray tube with a Cu anode (Kα1 = 1.540598 Å), model PW3373/00, with a long focus, 2200W, 60kV. A Ni Kβ filter was used. The detector used was the X’Celerator, RTMS (Real Time Multiple Scanning) type, operating in Scanning mode with an active length of 2.122°. The following instrumental conditions were used: scan from 5° to 75° 2θ, voltage: 40 kV, current: 30 mA, step size: 0.02° 2θ and time/step: 5s, 1/2° divergent slit and 1° antiscattering; 10 mm mask, sample movement: Spinning, with 1 rotation/s. The data was obtained using X Pert Data Collector software, version 2.1a, and processed using X Pert High Score software, version 2.1b, from PAnalytical, consulting the PDF database (Powder Diffraction File) of the ICDD (International Center for Diffraction Data). X-ray Fluorescence Spectrometry The spectrometer used to determine the chemical composition of kaolin was the sequential WDS, model Axios Minerals from PAnalytical, with a ceramic X-ray tube, rhodium (Rh) anode, and maximum power level of 2.4 KW. The preparation method was the fused disc method: 1 g of sample +6 g of flux (lithium tetraborate - Li2B4O7), mixed and melted at 1000 °C for 10 min. Data acquisition and processing were performed using the SuperQ Manager software from PAnalytical. Differential Thermal Analysis and Thermogravimetric Analysis The thermal decomposition curves of the kaolin filler were obtained using a simultaneous thermal analyzer (STA 1000/1500, PL Thermal Sciences, Stanton Redcroft Ltd.) equipped with a vertical cylindrical furnace and a digital converter coupled to a microcomputer. A platinum (87%)/rhodium (13%) thermocouple and an alumina crucible were used for samples of approximately 10 mg. The analyses were carried out under an inert atmosphere (nitrogen flow rate) at a heating rate of 20 °C/min, over the temperature range from 25 to 1000 °C. Granulometric Analysis The equipment used for this analysis was the Laser Particle Sizer analysette 22 from Fritsch GmbH, with the aid of MaScontrol software, also from Fritsch GmbH, for data acquisition and generation of the particle size distribution graph for the kaolin filler and metakaolin. Scanning Electron Microscopy Scanning electron microscopy analysis of kaolin and metakaolin was performed using Zeiss equipment (model LEO 1430). For the synthesized zeolitic product, the samples were metallized with gold using an EMITECH K550 metallizer. Metallization was performed by the interaction between a pure Au target and Ar ions (argon gas) at a pressure of 2.10–1 mbar and a current of 25 mA for 150 s, resulting in the deposition of a film with an average thickness of ± 15 nm on the samples. The samples were structured on aluminum supports with a diameter of 10 mm using carbon adhesive tape. Results and Discussion The results obtained show the composition of the starting material using the X-ray Fluorescence (XRF) technique. Next, the thermal behavior of this material is analyzed using Thermogravimetry and Thermogravimetric Derivative analyses, allowing an analysis of the changes that occur during heating. The granulometric analysis shows the behavior of both kaolin and metakaolin, providing information on the particle size distribution in each material. Finally, the results obtained by X-ray Diffraction (XRD) and Scanning Electron Microscopy (SEM) are presented, addressing the results for kaolin, metakaolin, and the synthesized zeolite. X-ray Fluorescence of Kaolin Filler Table shows the chemical composition of the kaolin filler analyzed by X-ray fluorescence in comparison with results from the literature obtained by Zhou et al. 2Chemical Composition of Kaolin Filler by X-ray FluorescenceOxidesThis workZhou et al. Mahima Kumar et al. Abubakar et al. Al2O3 37.3239.9536.2742.90Fe2O3 0.53–0.3470.31Na2O0.19– –P2O5 0.10– 0.01SiO2 47.0846.5141.7155.40CaO––0.4510.07MgO––0.4280.04K2O–––1.30MnO 0.01TiO2 0.42–1.510.05Loss on Ignition14.3613.9513.16– Chemical Composition of Kaolin Filler by X-ray Fluorescence The results presented in Table reveal that the Al2O3 (37.32%) and SiO2 (47.08%) contents predominantly characterize the clay mineral kaolinite as the main component of the material investigated in this study. This composition suggests an adequate Si/Al ratio for the formation of zeolites. , Although the composition of materials of this nature can be influenced by geographical factors, it is worth noting that the values obtained in this study are like others reported in the literature. − This study also highlighted the presence of a low percentage of impurities, the main ones being 0.53% Fe2O3, 0.42% TiO2, and 0.19% Na2O, corroborating previous findings. Differential Thermal Analysis and Thermogravimetric Analysis Figure shows the differential thermal analysis (DTA) and thermogravimetric analysis (TG) curves of the kaolin filler. The TG curve shows a total mass loss of approximately 14%. In the DTA curve, a distinct peak at 536 °C corresponds to an endothermic process related to the formation of metakaolin, resulting from the dehydroxylation of kaolinite and the generation of an amorphous structure. A second exothermic peak at 992 °C indicates the crystallization of mullite or aluminum–silicon spinel. , TG and DTA curves of the kaolin filler. Granulometric Analysis According to Santos, coating kaolins are characterized by having 75–95% of their particles with a diameter below 2 μm, whereas filling kaolins have 20–65% of their particles below this size. The higher proportion of fine particles in coating kaolins provides better surface coverage and smoothness in ceramic applications, while filler kaolins, with a larger fraction of coarser particles, are typically used to reduce costs, adjust rheological properties, and influence the porosity and reactivity of the final material. Figure shows the results of the kaolin granulometric analysis, indicating that approximately 30% of the particles have a diameter smaller than 2 μm, classifying this material as a filler kaolin. This particle size distribution contributes to reducing zeolite synthesis costs compared to coating kaolins. Particle size distribution of kaolin. Figure shows a decrease in the number of particles in the 0.1–1 μm range, which can be attributed to the calcination of kaolin. During the transformation of kaolinite to metakaolinite, smaller particles tend to agglomerate due to sintering. This is reflected in the particle size distribution: for kaolin (Figure ), d10 = 0.8 μm, d50 = 3.4 μm, and d90 = 8.5 μm, whereas for metakaolin (Figure ), d10 = 1.6 μm, d50 = 4.7 μm, and d90 = 10.5 μm, indicating a clear agglomeration of particles. These results demonstrate that the calcination step effectively modifies the granulometry, which is important for the subsequent zeolite synthesis. Particle size distribution of metakaolin. X-ray Diffraction The X-ray diffraction pattern presented in Figure indicates that the kaolin filler is predominantly composed of kaolinite. The characteristic basal reflection of kaolinite is observed at approximately 12.3° (2θ), together with another intense reflection at about 24.9°, in agreement with PDF card 14–0164. Additionally, a weaker peak near 21°, is attributed to quartz (PDF 05–0490), indicating its presence as a minor phase. XRD pattern of the kaolin filler. Figure shows the diffractogram of the calcined material, whose result indicates that it is an amorphous material, as is characteristic of metakaolinite, with the presence of only one quartz peak. XRD pattern of the metakaolin. The metakaolin obtained after calcination was used as the precursor for zeolite synthesis. The effects of reaction time and Si/Al ratio on the product were systematically investigated, as summarized in Table . Additional results obtained under varying experimental conditions are provided in the Supporting Information. 3Synthesis Conditions of the Zeolitic Product at Different Experimental Times PZ-X-Y-ZExperimentsXRD PZ-0.57-60-03 PZ-0.57-120-03 PZ-0.57-180-03aPZ: zeolite product; X: Al/Na ratio; Y: time (min); Z: experiment. Synthesis Conditions of the Zeolitic Product at Different Experimental Times PZ: zeolite product; X: Al/Na ratio; Y: time (min); Z: experiment. Considering the nomenclature PZ-0.57-60-03, presented in Table , this refers to the zeolitic product synthesized with an Al/Na ratio of 0.57, synthesis time of 60 min, obtained in the third experiment. The other nomenclatures follow the same standardization, allowing systematic identification of the experimental conditions used. Figure shows the diffractograms obtained for the experiments conducted at synthesis times of 60, 120, and 180 min, enabling analysis of the influence of reaction time on the formation of crystalline phases in the synthesized material. XRD patterns of the zeolitic material synthesized at 60, 120, and 180 min. Figure shows the main characteristic peaks of NaA zeolite, as identified by PDF standard 089-8015. These results indicate that the synthesis conditions adopted, temperature between 100 and 120 °C, Al/Na ratio = 0.57, pressure of 1.5 Kgf/cm2, and maximum time of 180 min, were favorable for the formation of this type of zeolite, allowing the system to reach structural stability. In addition, hydroxysodalite was observed in all diffractograms, with no significant differences between the synthesis times evaluated. Even for the shortest time tested (30 min; see Supporting Information), the synthesized products showed similar characteristics, suggesting that prolonged synthesis times are not necessary. These findings reinforce that the semipilot scale production system with steam heating has proven effective in obtaining NaA-type zeolite. Phase identification and confirming the formation of zeolite A under semipilot synthesis conditions were the main goals of the XRD analysis. The diffraction patterns showed the distinctive reflections of zeolite A, indicating successful crystallization. Complementary methods like SEM, XRF, and TG/DTA analyses further supported the structural interpretation by confirming the stability and formation of the synthesized material. Scanning Electron Microscopy Figure shows a micrograph of the kaolin filler, revealing a pseudohexagonal flaky morphology, typical of kaolinitic clays, as described by Schwanke et al. SEM micrographs of the kaolin filler. Figure shows the scanning electron microscopy of metakaolin, whose micrograph reveals a pseudohexagonal morphology, like the one observed in the analysis of kaolin. In addition, the presence of strongly agglomerated particles is noted, a characteristic that may influence their properties and reactivity in subsequent processes. SEM micrographs of the metakaolin. Scanning electron microscopy analysis was performed for the 180 min experiment, allowing the evaluation of the morphology of the zeolitic product used in the adsorption assays. Figure presents the SEM results obtained for experiment PZ-0.57-180-01, showing cubic and spherical morphologies characteristic of zeolite A and hydroxysodalite, respectively. SEM micrographs of zeolite products synthesized at Al/Na = 0.57 and a synthesis time of 180 min, with scale bars of (a) 10 μm and (b) 5 μm. The results of scanning electron microscopy, shown in Figures a-b, revealed a cubic morphology characteristic of zeolite A, in addition to the presence of several spherical crystals, indicating the formation of the sodalite zeolite phase. In Figure a, a considerable amount of agglomerated crystals and small portions of unreacted kaolinite were observed, attributed to the shorter synthesis time evaluated. However, this condition did not prevent the formation of the zeolitic product of interest. Copper Ion Adsorption The zeolitic product synthesized in this study was subjected to adsorption experiments to evaluate its effectiveness as an adsorbent solid. For this purpose, kinetics, equilibrium, pH variation, and adsorbent mass tests were performed. Adsorption Kinetics, pH Variation, and Adsorbent Mass Figure shows the adsorption kinetics of Cu2+ ions on the synthesized adsorbent, indicating that adsorption increases over time and reaches equilibrium at approximately 120 min for all concentrations evaluated. Adsorption kinetics of Cu2+ ions. Previous studies have reported different equilibrium times depending on the zeolite structure and the adsorbate involved. For example, Arslan et al., observed equilibrium times of approximately 30 min for NH4 + adsorption using faujasite zeolites, while Jamil et al., reported efficient removal of several metal ions using zeolite A. The differences in equilibrium time observed among studies may be associated with variations in zeolite framework type, pore structure, and physicochemical properties of the adsorbate. In the present work, the kinetic profile suggests a gradual occupation of available active sites, with equilibrium being achieved after approximately 120 min. Figure shows the adsorption capacity of the synthesized zeolite as a function of pH, considering concentrations of 60 and 500 ppm in three pH ranges: 3, 4, and 5. The results indicate that higher pH values favor adsorption. A similar trend was reported by Chen et al., who synthesized zeolite 4A and attributed the increase in adsorption capacity at higher pH to less competition for active sites between hydrogen ions and Sr­(II) metal. At lower pH values, this competition intensified, reducing the adsorption of Sr­(II). Effect of pH on the adsorption capacity of Cu2+ at different initial concentrations. The influence of the variation in adsorbent mass on the adsorption experiments was evaluated and is shown in Figure . The analysis was conducted for concentrations of 80, 300, and 1000 ppm. The results indicated that increasing the amount of adsorbent reduced the adsorption capacity, suggesting that a large amount of material is not necessary for the efficient removal of copper ions (Cu2+). Effect of variation in adsorbent mass on the adsorption capacity (q) of Cu2+ at different initial concentrations (80, 300, and 1000 ppm). Adsorption Equilibrium and Estimation of Isothermal Parameters The equilibrium data were obtained at four different temperatures: 25 °C, 50 °C, and 75 °C. Figure a-c shows the resulting equilibrium curves, highlighting the effectiveness of the synthesized zeolite in the adsorption of copper ions. It also shows the results of the estimates obtained with MCMC for the Langmuir, Freundlich, and Sips isotherms. Adsorption isotherms of Cu2+ onto the synthesized zeolite at (a) 25 °C, (b) 50 °C, and (c) 75 °C. The equilibrium curves shown in Figure a-c exhibited an initial increase in qe at low equilibrium concentrations. This behavior is associated with the high availability of active adsorption sites on the surface of zeolite. As the Cu2+ concentration increases, progressive site occupation leads to a reduction in the slope of the curves, indicating the approach to saturation. A temperature of 75 °C exhibited the highest adsorption capacity, demonstrating the most efficient performance in experimental terms. However, considering practical applicability in aqueous systems and the cost–benefit balance, a temperature of 50 °C also provided satisfactory results, representing a more feasible and economical option for real processes with lower thermal energy consumption. At lower temperatures, such as 25 °C, the amount of adsorbed Cu2+ ions was significantly lower compared to both 50 and 75 °C conditions. The ideal temperature for achieving good adsorption results was 75 °C. In comparison to the other evaluated conditions, the amount of adsorbed Cu2+ ions was significantly lower at lower temperatures, such as 25 °C. As a result, 75 °C is clearly the most effective temperature for the adsorption tests, offering improved performance while preserving advantageous operating conditions and energy consumption. The MCMC method proved to be an effective approach for estimating the parameters of the adsorption isotherms, showing that the Langmuir, and Sips models were in good agreement with the experimental data at temperatures of 25, 50, and 75 °C. Based on the Bayesian information criterion presented in Table , it was possible to quantitatively identify the most appropriate isotherm to represent the experimental conditions under which the data were obtained. Table presents the values obtained for the Bayesian model selection metric, where the lowest value recorded indicates the model most likely to adequately represent the physical phenomenon under study. 4Isotherm Models with Obtained BIC Values Temperature (°C)Isotherm255075Langmuir 36.15 37.7640.25Freundlich38.2043.7148.47Sips37.13 34.61 33.30 Isotherm Models with Obtained BIC Values At 25 °C, the Langmuir model presented the lowest Bayesian information criterion (36.15), although the Sips isotherm showed a very similar value (37.13). In contrast, at 50 and 75 °C the Sips isotherm produced the lowest BIC values, demonstrating a superior description of the adsorption equilibrium at elevated temperatures. The Freundlich model exhibited higher BIC values at all temperatures and was therefore less adequate for representing the experimental data. Table presents the estimated values for the parameters obtained using the MCMC methodology, which can be used as a priori information in future investigations involving Bayesian modeling and adsorption phenomena. In addition, R2 values are reported to support the evaluation of model performance. The results indicate that the Langmuir model provides the best fit at 25 °C, whereas the Sips isotherm performs better at 50 and 75 °C. 5Estimated values for parameters with MCMCModelTemperature (°C)IsothermsParameters255075LangmuirK (L/mg)0.010.010.02 qm (mg/g)107.52124.10119.89 R2 0.950.940.94FreundlichKF (mg/g)(L/mg)1/n 4.047.2211.33 n (−)1.892.182.58 R2 0.920.880.84SipsK S (L/mg)195.2993.0990.75 β S (−)0.711.973.07 a S (L/mg)0.0020.020.03 R2 0.930.980.99 Estimated values for parameters with MCMC Conclusion Kaolin filler was successfully used as a precursor in the hydrothermal synthesis of zeolitic materials. The heat required for the reaction was provided by steam generated in a boiler, allowing precise control of operating variables such as system temperature and pressure and significantly reducing the synthesis time to just 3 h. The method and the scale employed in this study represent a viable alternative to producing zeolites in larger quantities than those typically obtained in laboratory-scale experiments. The adsorption data were best described by the Langmuir model at 25 °C and by the Sips isotherm at 50 and 75 °C, as indicated by both R2 and the Bayesian Information Criterion. Parameters estimated using the MCMC method provide a reliable basis for future investigations involving Bayesian modeling and can serve as prior information for subsequent studies. The obtained zeolitic product proved effective for the adsorption of copper ions, a potentially toxic element, exhibiting high removal capacity under the tested conditions. Its performance highlights the material’s suitability for treating industrial or highly concentrated effluents and demonstrates the practical potential of the synthesized zeolite for environmental remediation applications. Supplementary Material