RETRACTED ARTICLE: An enzymatic BioBattery based on multicopper oxidases with reduced substrate diffusion constraints for sustainable energy harvesting Authors: Vivek Saxena, Narendra Kumar, Uma Nangia, Saibal Manna, Ankush Gupta, Manoj Kumar Kar Published: 2026 ABSTRACT The development of efficient enzymatic energy conversion systems is often limited by restricted substrate transport to the electrode surface and instability of immobilized biocatalysts. In this work, we report the design and experimental validation of an enzymatic fuel cell, referred to as a BioBattery, aimed at reducing substrate diffusion constraints through the co-immobilization of catalytic components within a structured electrode matrix. The system employs multicopper oxidases as anodic biocatalysts, and three enzymes—multicopper oxidase from Pyrobaculum aerophilum, laccase from Trametes versicolor, and bilirubin oxidase from Myrothecium verrucaria—were systematically evaluated to identify the most effective anodic configuration. In parallel, different cathodic architectures were investigated with emphasis on oxygen reduction as the terminal electron-accepting reaction. The optimal configuration consisted of the multicopper oxidase preparation from Pyrobaculum aerophilum at the anode coupled with an amine-reactive phenazine ethosulfate-modified bovine serum albumin (arPES–BSA) matrix at the cathode, where BSA acts as a structural scaffold for mediator immobilization. The resulting BioBattery was further integrated with a previously reported BioCapacitor system and demonstrated reproducible charging of a 470 μF capacitor. The obtained results highlight the potential of structured enzyme–mediator architectures to improve the operational stability and electrochemical performance of enzymatic energy devices. Overall, the proposed BioBattery configuration provides a promising platform for sustainable energy harvesting in low-power applications such as wearable and implantable electronic systems. Introduction Over the past few decades, enzymatic fuel cells have evolved into a significant and rapidly expanding area of scientific investigation. Their development has attracted substantial interest from diverse research communities, encompassing sustainable and renewable energy technologies, nanotechnology-enabled device engineering, electrochemical energy conversion, and advanced functional materials. This multidisciplinary engagement reflects the growing recognition of enzymatic fuel cells as promising platforms for environmentally benign power generation and biointegrated energy systems1–4. Their ability to convert biochemical energy into electrical power has enabled diverse applications, notably in wearable and implantable sensors, smart textiles, and environmental monitoring platforms. A distinguishing feature of enzyme fuel cells is their fuel flexibility, allowing operation with a wide range of substrates, from endogenous biomolecules such as glucose in implantable devices to complex organic matter present in wastewater streams used in treatment systems5. Despite these advantages, enzyme fuel cells face several critical challenges that limit their broader deployment. Key issues include insufficient long-term operational stability, relatively low power output compared to conventional energy sources, and constraints on miniaturization for compact system integration. Although recent advances have reported notable improvements in power density, enzyme deactivation and performance degradation over extended operation remain persistent concerns6–8. Nevertheless, enzyme-based energy systems offer distinct advantages over traditional power technologies. These systems can operate efficiently under physiological conditions, catalyze electrochemical reactions at ambient or body temperature and near-neutral pH, and significantly reduce environmental and biological waste associated with conventional power generation. As a result, enzyme fuel cells continue to represent a promising class of bioelectrochemical energy devices, particularly for applications requiring biocompatibility, sustainability, and low environmental impact. A fundamental limitation of many enzymatic biofuel cells lies in their reliance on the diffusion of fuel from the surrounding bulk medium into the electrochemically active region of the anode. This diffusion-dependent operation represents a major distinction from conventional coin-type batteries widely employed in medical devices, which store reactants internally and therefore do not depend on external mass transport. As a result, enzymatic fuel cells face intrinsic constraints on achievable in vivo power density. Several studies have demonstrated that the concentrations of physiologically available fuels in the human body are inherently low. Reported values indicate glucose concentrations typically in the range of 4–7 mM, lactate levels of approximately 1–3 mM, and dissolved oxygen concentrations near 0.1 mM under physiological conditions9–11. These limited substrate levels impose strict upper bounds on the reaction rates of enzymatic systems. Moreover, many enzymatic fuel cells operate under mass-transport-limited regimes, where the diffusion rate of substrates from the bulk environment governs the maximum attainable current and power output. Tissue encapsulation and biofouling can form diffusion barriers around the device, reducing substrate availability at the electrode surface and progressively degrading performance. In addition to mass transport constraints, enzymatic fuel cells typically exhibit relatively low output voltages. Due to internal resistive losses and kinetic overpotentials, the operating voltage of such systems often remains below 700 mV, which is insufficient for direct operation of most modern microscale electronic components that commonly require supply voltages in the range of 0.8–1.2 V12,13. To address these challenges, various strategies have been proposed, including the use of nanostructured electrodes to increase effective surface area and the deployment of devices in regions with enhanced convective transport, such as blood vessels, to alleviate diffusion limitations. While these approaches can improve power density and operational viability, they often constrain device placement or introduce significant challenges for miniaturization and system integration. An alternative and potentially more scalable solution involves integrating the fuel source directly within the enzymatic biofuel cell. Such an approach would decouple power generation from external diffusion constraints, facilitate device miniaturization, and enable form factors more closely resembling those of conventional coin-cell batteries. By internalizing the substrate, enzymatic biofuel cells could achieve improved reliability and broader applicability in implantable microsystems. This work introduces an enzyme-based fuel cell configuration in which the energy source is inherently embedded within the anode matrix, forming a self-contained system referred to as a bio-battery. In this architecture, the fuel substrate is co-immobilized alongside the corresponding biocatalytic enzyme, as depicted schematically in Fig. 1a. This integrated arrangement enables continuous and sustained power generation without dependence on external fuel replenishment or bulk mass transport from the surrounding environment. Moreover, the elimination of a separate membrane obviates the requirement for fuel diffusion across interfacial barriers, thereby reducing structural complexity and enhancing operational stability. The proposed platform is designed to preserve biocompatibility while adhering to principles of environmental sustainability.Fig. 1(a) Schematic Illustration of the Non–Diffusion-Limited Enzymatic BioBattery Architecture. (b) Schematic illustration of the design, optimization, and application pathway of the proposed BioBattery system. (a) Schematic Illustration of the Non–Diffusion-Limited Enzymatic BioBattery Architecture. (b) Schematic illustration of the design, optimization, and application pathway of the proposed BioBattery system. The anode surface was modified by immobilizing a hyperthermostable multicopper oxidase onto carbon paper using glutaraldehyde as a covalent cross-linking agent. The enzyme employed in this study originates from the hyperthermophilic archaeon McoP, as reported in earlier investigations. Glutaraldehyde-based cross-linking is known to promote polymerization processes, leading to the formation of structurally complex networks, including polyphenolic-like assemblies14. Experimental observations revealed that McoP can oxidize the cross-linked glutaraldehyde matrix, thereby utilizing it as an intrinsic electron donor. When this anodic reaction is integrated with cathodic systems containing PES, efficient electrochemical energy generation can be achieved. To complement the optimized anode architecture, the cathode surface was engineered via the immobilization of BSA chemically modified with arPES. This tailored cathodic interface facilitates effective electron mediation while simultaneously preserving mechanical integrity and electrochemical stability under continuous operating conditions. The resulting enzymatic fuel cell was subsequently coupled with a previously established BioCapacitor platform, which has been validated in earlier studies for its capability to reliably power miniaturized electronic components, including glucose sensors, microprocessors, and stepper motors15. Figure 1b schematically summarizes the design strategy, optimization pathway, and application potential of the proposed BioBattery, from enzymatic configuration screening under non-diffusion-limited operation to BioCapacitor integration and energy delivery for wearable and implantable devices. While multicopper oxidases are conventionally employed as cathodic biocatalysts for oxygen reduction, their deployment at the anode in this study is based on their intrinsic ability to oxidize polyphenolic substrates. multicopper oxidases catalyze the oxidation of phenolic compounds to the corresponding quinones through a four-electron transfer process coupled with oxygen reduction. In this BioBattery architecture, the glutaraldehyde cross-linking process creates polyphenolic-like structures within the anode matrix. The McoP enzyme, in particular, has demonstrated activity toward these glutaraldehyde-derived structures, enabling the oxidation of the matrix itself to serve as the electron source. This unconventional use is mechanistically justified by:The known substrate promiscuity of multicopper oxidases toward polyphenolic compounds,The formation of phenolic structures during glutaraldehyde polymerization, andThe thermodynamic feasibility of polyphenol oxidation by MCOs under the operating conditions. The known substrate promiscuity of multicopper oxidases toward polyphenolic compounds, The known substrate promiscuity of multicopper oxidases toward polyphenolic compounds, The formation of phenolic structures during glutaraldehyde polymerization, and The formation of phenolic structures during glutaraldehyde polymerization, and The thermodynamic feasibility of polyphenol oxidation by MCOs under the operating conditions. The thermodynamic feasibility of polyphenol oxidation by MCOs under the operating conditions. Methods Regents and material In this study, a combination of biological catalysts, electrode materials, chemical reagents, and electronic components was employed to construct and evaluate the proposed bioelectrochemical system. Multiple multicopper oxidases—including a recombinantly produced enzyme derived from Pyrobaculum aerophilum as well as commercially available laccase and bilirubin oxidase—were investigated to assess their electrochemical performance under comparable conditions. The recombinant enzyme was heterologously expressed in Escherichia coli using a standard expression vector system. Electrode fabrication utilized gold disk electrodes and carbon-based substrates, complemented by conductive additives and cross-linking agents to enable stable enzyme immobilization. Redox-active mediators and protein-based modifiers were incorporated to facilitate efficient electron transfer at the cathode interface. Power management and load control were achieved using low-power electronic components, while all electrochemical measurements were conducted using a precision potentiostat. A detailed overview of the enzymes, materials, instrumentation, and their respective roles is provided in Table 1, ensuring transparency and reproducibility of the experimental framework.Table 1Materials, biological components, and instrumentation used in the study.CategoryMaterial/componentSource/specificationRemarks/role in studyMulticopper oxidasesMcoPRecombinant expression from Pyrobaculum aerophilumProduced in-house using heterologous expression; used as anodic biocatalystLaccaseTrametes versicolorCommercially obtained enzyme; comparative anodic catalystBODMyrothecium verrucariaCommercial enzyme; evaluated for cathodic reactionsProteinBSACommercial reagentUsed for cathode functionalization and protein immobilizationExpression systemExpression vectorpET-11a-pae1888Vector used for recombinant McoP productionHost strainEscherichia coli BL21-CodonPlus (DE3)-RIPLHost for heterologous enzyme expressionElectrode materialsGDEBAS Inc., JapanUsed for electrochemical characterizationTCPFuelCellEarth, USAAnode and cathode substrate materialRedox mediatorarPESDojindo Molecular Technology, USAOxygen-sensitive redox mediatorCross-linking / reagentsGlutaraldehyde (25% aqueous solution)MilliporeSigma, USAEnzyme immobilization and cross-linkingTriton X-100MilliporeSigma, USASurfactant for electrode preparationConductive additivesKB powderMitsubishi Chemical Corp., JapanConductive carbon additivePower managementUltralow-power boost regulator (ADP5090)Analog Devices, USAEnergy harvesting and charge managementLoad controlDecade resistance boxEisco (Amazon)Electrical load variationElectrochemical analysisPotentiostatVSP-3e (BioLogic)Electrochemical measurements and data acquisition Table 1Materials, biological components, and instrumentation used in the study.CategoryMaterial/componentSource/specificationRemarks/role in studyMulticopper oxidasesMcoPRecombinant expression from Pyrobaculum aerophilumProduced in-house using heterologous expression; used as anodic biocatalystLaccaseTrametes versicolorCommercially obtained enzyme; comparative anodic catalystBODMyrothecium verrucariaCommercial enzyme; evaluated for cathodic reactionsProteinBSACommercial reagentUsed for cathode functionalization and protein immobilizationExpression systemExpression vectorpET-11a-pae1888Vector used for recombinant McoP productionHost strainEscherichia coli BL21-CodonPlus (DE3)-RIPLHost for heterologous enzyme expressionElectrode materialsGDEBAS Inc., JapanUsed for electrochemical characterizationTCPFuelCellEarth, USAAnode and cathode substrate materialRedox mediatorarPESDojindo Molecular Technology, USAOxygen-sensitive redox mediatorCross-linking / reagentsGlutaraldehyde (25% aqueous solution)MilliporeSigma, USAEnzyme immobilization and cross-linkingTriton X-100MilliporeSigma, USASurfactant for electrode preparationConductive additivesKB powderMitsubishi Chemical Corp., JapanConductive carbon additivePower managementUltralow-power boost regulator (ADP5090)Analog Devices, USAEnergy harvesting and charge managementLoad controlDecade resistance boxEisco (Amazon)Electrical load variationElectrochemical analysisPotentiostatVSP-3e (BioLogic)Electrochemical measurements and data acquisition Materials, biological components, and instrumentation used in the study. Preparation of McoP The multicopper oxidase derived from McoP was obtained through recombinant expression followed by a multistep purification protocol designed to enhance enzymatic stability and catalytic activity. The enzyme was heterologously expressed in a specialized Escherichia coli strain using a plasmid-based expression system and cultivated under controlled shake-flask conditions. Following biomass recovery, cell disruption was achieved through ultrasonication, and insoluble debris was removed by centrifugal clarification. To ensure proper metal cofactor incorporation, the clarified enzyme solution was incubated with copper ions prior to a short thermal treatment, which selectively enriched the thermostable enzyme fraction. The purified enzyme was subsequently transferred into a buffered medium suitable for electrochemical applications. A step-by-step overview of the expression and purification workflow is provided in Table 2, highlighting the key operational stages employed in this study.Table 2Summary of recombinant expression and purification procedure for McoP.Process stageMethodological descriptionExpression systemRecombinant enzyme produced using a plasmid-based bacterial expression systemHost organismEscherichia coli BL21-CodonPlus (DE3)-RIPLCultivation conditionsShake-flask cultivation in conical flasks at elevated temperature under continuous agitationCell harvestingBiomass collected by centrifugal separationCell disruptionUltrasonication performed in a low-ionic-strength Tris–HCl bufferClarification stepRemoval of cell debris via high-speed centrifugationMetal incorporationIncubation of clarified lysate with copper ions to activate the multicopper enzymeThermal treatmentShort-duration heat treatment to improve enzyme purity and stabilityBuffer exchangeFinal exchange into alkaline Tris–HCl buffer for downstream use Table 2Summary of recombinant expression and purification procedure for McoP.Process stageMethodological descriptionExpression systemRecombinant enzyme produced using a plasmid-based bacterial expression systemHost organismEscherichia coli BL21-CodonPlus (DE3)-RIPLCultivation conditionsShake-flask cultivation in conical flasks at elevated temperature under continuous agitationCell harvestingBiomass collected by centrifugal separationCell disruptionUltrasonication performed in a low-ionic-strength Tris–HCl bufferClarification stepRemoval of cell debris via high-speed centrifugationMetal incorporationIncubation of clarified lysate with copper ions to activate the multicopper enzymeThermal treatmentShort-duration heat treatment to improve enzyme purity and stabilityBuffer exchangeFinal exchange into alkaline Tris–HCl buffer for downstream use Summary of recombinant expression and purification procedure for McoP. Enzyme activity assays The specific activities of the multicopper oxidases were determined spectrophotometrically using appropriate substrates under standardized conditions:McoP (Pyrobaculum aerophilum) Activity measured using 2, 6-dimethoxyphenol (DMP) as substrate (ε = 14,800 M⁻1 cm⁻1 at 468 nm). Specific activity: 356 ± 15 U/mg (pH 7.0, 25 °C).Laccase (Trametes versicolor) Activity measured using ABTS as substrate (ε = 36,000 M⁻1 cm⁻1 at 420 nm). Specific activity: 120 ± 8 U/mg (pH 4.5, 25 °C).BOD (Myrothecium verrucaria) Activity measured using bilirubin as substrate (ε = 39,000 M⁻1 cm⁻1 at 440 nm). Specific activity: 85 ± 6 U/mg (pH 7.0, 25 °C). McoP (Pyrobaculum aerophilum) Activity measured using 2, 6-dimethoxyphenol (DMP) as substrate (ε = 14,800 M⁻1 cm⁻1 at 468 nm). Specific activity: 356 ± 15 U/mg (pH 7.0, 25 °C). McoP (Pyrobaculum aerophilum) Activity measured using 2, 6-dimethoxyphenol (DMP) as substrate (ε = 14,800 M⁻1 cm⁻1 at 468 nm). Specific activity: 356 ± 15 U/mg (pH 7.0, 25 °C). Laccase (Trametes versicolor) Activity measured using ABTS as substrate (ε = 36,000 M⁻1 cm⁻1 at 420 nm). Specific activity: 120 ± 8 U/mg (pH 4.5, 25 °C). Laccase (Trametes versicolor) Activity measured using ABTS as substrate (ε = 36,000 M⁻1 cm⁻1 at 420 nm). Specific activity: 120 ± 8 U/mg (pH 4.5, 25 °C). BOD (Myrothecium verrucaria) Activity measured using bilirubin as substrate (ε = 39,000 M⁻1 cm⁻1 at 440 nm). Specific activity: 85 ± 6 U/mg (pH 7.0, 25 °C). BOD (Myrothecium verrucaria) Activity measured using bilirubin as substrate (ε = 39,000 M⁻1 cm⁻1 at 440 nm). Specific activity: 85 ± 6 U/mg (pH 7.0, 25 °C). Note: One unit (U) is defined as the amount of enzyme that oxidizes 1 μmol of substrate per minute under the specified conditions. Detailed cross-linking conditions The glutaraldehyde vapor cross-linking was carried out under controlled experimental conditions as described below:Glutaraldehyde concentration 25% (v/v) aqueous glutaraldehyde solution.Vapor exposure time 2 h at room temperature (25 ± 2 °C).Chamber setup The electrodes were placed inside a sealed desiccator containing a reservoir of 25% glutaraldehyde solution (10 mL). The reservoir was positioned in such a way that direct contact between the liquid glutaraldehyde and the electrode surface was avoided, allowing only vapor-phase cross-linking to occur.Post-cross-linking treatment After vapor exposure, the electrodes were immediately transferred to 100 mM potassium phosphate buffer (PPB, pH 7.0) for stabilization and storage prior to electrochemical measurements. Glutaraldehyde concentration 25% (v/v) aqueous glutaraldehyde solution. Glutaraldehyde concentration 25% (v/v) aqueous glutaraldehyde solution. Vapor exposure time 2 h at room temperature (25 ± 2 °C). Vapor exposure time 2 h at room temperature (25 ± 2 °C). Chamber setup The electrodes were placed inside a sealed desiccator containing a reservoir of 25% glutaraldehyde solution (10 mL). The reservoir was positioned in such a way that direct contact between the liquid glutaraldehyde and the electrode surface was avoided, allowing only vapor-phase cross-linking to occur. Chamber setup The electrodes were placed inside a sealed desiccator containing a reservoir of 25% glutaraldehyde solution (10 mL). The reservoir was positioned in such a way that direct contact between the liquid glutaraldehyde and the electrode surface was avoided, allowing only vapor-phase cross-linking to occur. Post-cross-linking treatment After vapor exposure, the electrodes were immediately transferred to 100 mM potassium phosphate buffer (PPB, pH 7.0) for stabilization and storage prior to electrochemical measurements. Post-cross-linking treatment After vapor exposure, the electrodes were immediately transferred to 100 mM potassium phosphate buffer (PPB, pH 7.0) for stabilization and storage prior to electrochemical measurements. Detailed buffer conditions The buffer system used in all electrochemical and enzymatic experiments was prepared as follows:Potassium phosphate buffer (PPB) 100 mM, pH 7.0 (± 0.1).Preparation 13.7 g of K₂HPO₄ and 3.4 g of KH₂PO₄ were dissolved in 1 L of Milli-Q water (resistivity 18.2 MΩ cm).pH adjustment The pH was adjusted, when required, using 1 M HCl or 1 M KOH.Temperature conditions Unless otherwise stated, all experiments were conducted at a temperature of 25 ± 2 °C. Potassium phosphate buffer (PPB) 100 mM, pH 7.0 (± 0.1). Potassium phosphate buffer (PPB) 100 mM, pH 7.0 (± 0.1). Preparation 13.7 g of K₂HPO₄ and 3.4 g of KH₂PO₄ were dissolved in 1 L of Milli-Q water (resistivity 18.2 MΩ cm). Preparation 13.7 g of K₂HPO₄ and 3.4 g of KH₂PO₄ were dissolved in 1 L of Milli-Q water (resistivity 18.2 MΩ cm). pH adjustment The pH was adjusted, when required, using 1 M HCl or 1 M KOH. pH adjustment The pH was adjusted, when required, using 1 M HCl or 1 M KOH. Temperature conditions Unless otherwise stated, all experiments were conducted at a temperature of 25 ± 2 °C. Temperature conditions Unless otherwise stated, all experiments were conducted at a temperature of 25 ± 2 °C. Synthesis and processing of KB-based Ink and arPES-modified proteins The preparation of conductive ink and protein–mediator conjugates followed standardized yet carefully controlled protocols to ensure reproducibility and material stability. A Ketjen Black–based ink was formulated using an aqueous dispersion containing a nonionic surfactant and subjected to extended sonication to achieve uniform particle distribution. To maintain homogeneity, the ink was re-dispersed prior to each application. In parallel, BSA was chemically modified with an amine-reactive phenazine derivative under low-temperature conditions to preserve protein integrity. The conjugation reaction was followed by repeated centrifugal buffer exchange to remove excess reagents and stabilize the final product. A detailed summary of the reagents, processing conditions, and functional objectives associated with these preparation steps is provided in Table 3.Table 3Summary of KB Ink Preparation and arPES–BSA Conjugation Procedures.ProcessMaterials/reagentsComposition/conditionsPurposeProcessing parametersKB ink formulationKetjen Black (KB), Milli-Q water, Triton X-10015 mg KB, 670 μL water, 30 μL surfactantPreparation of homogeneous conductive inkSonication for 1 h; stored in dark; re-sonicated for 0.5 h before usearPES–BSA conjugationBSA, arPES, PPB140 μL BSA, 100 μL PPB, 10 μL arPESCovalent modification of protein with redox mediatorMixing at 1200 rpm for 0.5 h at 4 °CBuffer exchangeConjugated arPES–BSA solution–Removal of unreacted species and buffer equilibrationCentrifugation at 14,000 g, 4 °C, 5 min; repeated 10 cycles Table 3Summary of KB Ink Preparation and arPES–BSA Conjugation Procedures.ProcessMaterials/reagentsComposition/conditionsPurposeProcessing parametersKB ink formulationKetjen Black (KB), Milli-Q water, Triton X-10015 mg KB, 670 μL water, 30 μL surfactantPreparation of homogeneous conductive inkSonication for 1 h; stored in dark; re-sonicated for 0.5 h before usearPES–BSA conjugationBSA, arPES, PPB140 μL BSA, 100 μL PPB, 10 μL arPESCovalent modification of protein with redox mediatorMixing at 1200 rpm for 0.5 h at 4 °CBuffer exchangeConjugated arPES–BSA solution–Removal of unreacted species and buffer equilibrationCentrifugation at 14,000 g, 4 °C, 5 min; repeated 10 cycles Summary of KB Ink Preparation and arPES–BSA Conjugation Procedures. Cathodic reaction mechanism The arPES–BSA conjugate functions as an oxygen-sensitive redox mediator. The formal potential (E°′) of PES is approximately − 210 mV vs. NHE. During operation, the reduced form of arPES (arPESH) donates electrons to molecular oxygen. The primary reduction product is superoxide radical (O₂·⁻), formed through the following reaction:1\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\mathrm{arPESH}} + {\mathrm{O}}_{{2}} \to {\mathrm{arPES}}^{{ + }} + {\mathrm{O}}_{{2}} \cdot^{ - } + {\mathrm{H}}^{{ + }}$$\end{document} This single-electron transfer to oxygen is characteristic of phenazine-mediated oxygen reduction. The superoxide radical can subsequently undergo disproportionation (2O₂·⁻ + 2H⁺ → H₂O₂ + O₂) or further reduction depending on the local environment and available reducing equivalents. Preparation of enzyme inks and biobattery electrodes To construct the bioelectrochemical interfaces, enzyme-based inks were formulated for both anodic and cathodic configurations using defined ratios of catalytic proteins, conductive carbon additives, and buffering media. Multicopper oxidases and redox-active protein complexes were dispersed with Ketjen black to enhance electrical conductivity and stabilize enzyme–electrode interactions. The detailed composition of each enzyme ink, including enzyme concentration and volume fractions, is summarized in Table 4.Table 4Composition of enzyme inks used for anode and cathode fabrication.Electrode typeEnzyme systemConductive additiveEnzyme volume & concentrationBuffer volume (μL PPB)AnodeMcoP3 μL Ketjen black ink10 μL (40 mg mL⁻1)17AnodeBOD3 μL Ketjen black ink10 μL (5.4 mg mL⁻1)17AnodeLaccase3 μL Ketjen black ink10 μL (40 mg mL⁻1)17CathodearPES-BSA3 μL Ketjen black ink10 μL (50 mg mL⁻1)17CathodeBOD3 μL Ketjen black ink10 μL (5.4 mg mL⁻1)17CathodeLaccase3 μL Ketjen black ink10 μL (40 mg mL⁻1)17 Table 4Composition of enzyme inks used for anode and cathode fabrication.Electrode typeEnzyme systemConductive additiveEnzyme volume & concentrationBuffer volume (μL PPB)AnodeMcoP3 μL Ketjen black ink10 μL (40 mg mL⁻1)17AnodeBOD3 μL Ketjen black ink10 μL (5.4 mg mL⁻1)17AnodeLaccase3 μL Ketjen black ink10 μL (40 mg mL⁻1)17CathodearPES-BSA3 μL Ketjen black ink10 μL (50 mg mL⁻1)17CathodeBOD3 μL Ketjen black ink10 μL (5.4 mg mL⁻1)17CathodeLaccase3 μL Ketjen black ink10 μL (40 mg mL⁻1)17 Composition of enzyme inks used for anode and cathode fabrication. Electrode fabrication was carried out using either gold disk electrodes or Toray carbon paper substrates, depending on the intended BioBattery configuration. Gold electrodes underwent mechanical, chemical, and electrochemical pretreatment to ensure surface cleanliness and reproducibility, whereas carbon paper electrodes were prepared using a simplified cleaning protocol. In both cases, enzyme inks were immobilized via drop-casting and stabilized through glutaraldehyde vapor cross-linking, followed by buffer incubation and storage under controlled conditions. A step-by-step comparison of the preparation protocols for the two electrode platforms is provided in Table 5.Table 5Fabrication procedures for GDE-based and TCP-based BioBattery electrodes.StepGDE BioBattery preparationTCP BioBattery preparationSubstrateGDE (Φ = 2 mm)TCP (≈ 1 in × 1 in)Surface cleaningAlumina polishing (0.3 and 0.05 μm) followed by piranha treatment (H₂SO₄:H₂O₂, 3:1)Rinsing with deionized waterElectrochemical treatmentCyclic voltammetry (0.0–1.2 V) in 50 mM KOHNot appliedEnzyme depositionDrop-casting of anode or cathode enzyme inkDrop-casting of anode or cathode enzyme inkCross-linkingGlutaraldehyde vapor exposure (25% solution)Glutaraldehyde vapor exposure (25% solution)Storage100 mM PPB100 mM PPB Table 5Fabrication procedures for GDE-based and TCP-based BioBattery electrodes.StepGDE BioBattery preparationTCP BioBattery preparationSubstrateGDE (Φ = 2 mm)TCP (≈ 1 in × 1 in)Surface cleaningAlumina polishing (0.3 and 0.05 μm) followed by piranha treatment (H₂SO₄:H₂O₂, 3:1)Rinsing with deionized waterElectrochemical treatmentCyclic voltammetry (0.0–1.2 V) in 50 mM KOHNot appliedEnzyme depositionDrop-casting of anode or cathode enzyme inkDrop-casting of anode or cathode enzyme inkCross-linkingGlutaraldehyde vapor exposure (25% solution)Glutaraldehyde vapor exposure (25% solution)Storage100 mM PPB100 mM PPB Fabrication procedures for GDE-based and TCP-based BioBattery electrodes. Electrode area determination and biobattery performance evaluation The experimental evaluation of the BioBattery system comprised electrode surface area estimation, electrochemical performance characterization, and power generation assessment using external circuitry. The effective surface area of enzyme-functionalized TCP electrodes was quantified through image-based analysis of immobilized enzyme regions, enabling accurate normalization of current and power densities. Electrical characterization was performed by subjecting the assembled BioBattery to a broad range of resistive loads while monitoring voltage responses, from which current flow and power output were calculated. To assess practical energy delivery capability, the BioBattery was further integrated with a charge management circuit and capacitive storage elements, and the resulting charging behavior was evaluated under open-circuit conditions. A consolidated overview of these procedures and their objectives is provided in Table 6, ensuring methodological clarity and reproducibility.Table 6Summary of electrode area determination, BioBattery characterization, and power generation protocols.SubsectionProcedure focusMethodological descriptionKey outputs/purposeTCP Electrode surface area estimationDetermination of active anodic areaEnzyme-functionalized TCP electrodes were imaged, and surface areas of immobilized enzyme regions were quantified using image analysis software. The oval selection tool was applied to delineate enzyme spots, and measurements were averaged across multiple replicatesAccurate estimation of effective electrode area for normalization of current and power density valuesBioBattery electrical characterizationEvaluation of electrochemical performanceThe assembled anode–cathode pair was immersed in buffered electrolyte and connected to a potentiostat and external resistance box. A wide range of discrete resistive loads was sequentially applied while recording the corresponding cell voltageCalculation of current output and power generation under varying electrical loadsPower generation and energy storage assessmentIntegration with charge management circuitryThe BioBattery electrodes were interfaced with a low-power boost and charge management circuit connected to capacitors of different capacitances. The capacitor voltage was monitored to assess charging behavior and power delivery capabilityDemonstration of practical energy harvesting and storage feasibility Table 6Summary of electrode area determination, BioBattery characterization, and power generation protocols.SubsectionProcedure focusMethodological descriptionKey outputs/purposeTCP Electrode surface area estimationDetermination of active anodic areaEnzyme-functionalized TCP electrodes were imaged, and surface areas of immobilized enzyme regions were quantified using image analysis software. The oval selection tool was applied to delineate enzyme spots, and measurements were averaged across multiple replicatesAccurate estimation of effective electrode area for normalization of current and power density valuesBioBattery electrical characterizationEvaluation of electrochemical performanceThe assembled anode–cathode pair was immersed in buffered electrolyte and connected to a potentiostat and external resistance box. A wide range of discrete resistive loads was sequentially applied while recording the corresponding cell voltageCalculation of current output and power generation under varying electrical loadsPower generation and energy storage assessmentIntegration with charge management circuitryThe BioBattery electrodes were interfaced with a low-power boost and charge management circuit connected to capacitors of different capacitances. The capacitor voltage was monitored to assess charging behavior and power delivery capabilityDemonstration of practical energy harvesting and storage feasibility Summary of electrode area determination, BioBattery characterization, and power generation protocols. Three-electrode electrochemical measurements To determine the individual contributions of the anode and cathode to the overall cell performance, three-electrode measurements were conducted using the following configuration:Working electrode Anode (McoP-modified) or Cathode (arPES–BSA-modified)Counter electrode Platinum wireReference electrode Ag/AgCl (3 M KCl); all potentials were converted and reported versus the Normal Hydrogen Electrode (NHE) Working electrode Anode (McoP-modified) or Cathode (arPES–BSA-modified) Working electrode Anode (McoP-modified) or Cathode (arPES–BSA-modified) Counter electrode Platinum wire Counter electrode Platinum wire Reference electrode Ag/AgCl (3 M KCl); all potentials were converted and reported versus the Normal Hydrogen Electrode (NHE) Reference electrode Ag/AgCl (3 M KCl); all potentials were converted and reported versus the Normal Hydrogen Electrode (NHE) Measurement ProtocolOCP Individual electrode potentials were measured against the reference electrode in 100 mM phosphate buffer (PPB, pH 7.0) under quiescent conditions.Polarization Curves Linear sweep voltammetry (LSV) was performed from the OCP to − 0.2 V for the anode and + 0.8 V for the cathode at a scan rate of 1 mV s⁻1 to characterize the half-cell electrochemical behavior.Cyclic Voltammetry (CV) CV measurements were carried out in the potential range from − 0.5 V to + 0.8 V at scan rates of 5, 10, 20, 50, and 100 mV s⁻1 to evaluate the electron-transfer kinetics of the electrodes. OCP Individual electrode potentials were measured against the reference electrode in 100 mM phosphate buffer (PPB, pH 7.0) under quiescent conditions. OCP Individual electrode potentials were measured against the reference electrode in 100 mM phosphate buffer (PPB, pH 7.0) under quiescent conditions. Polarization Curves Linear sweep voltammetry (LSV) was performed from the OCP to − 0.2 V for the anode and + 0.8 V for the cathode at a scan rate of 1 mV s⁻1 to characterize the half-cell electrochemical behavior. Polarization Curves Linear sweep voltammetry (LSV) was performed from the OCP to − 0.2 V for the anode and + 0.8 V for the cathode at a scan rate of 1 mV s⁻1 to characterize the half-cell electrochemical behavior. Cyclic Voltammetry (CV) CV measurements were carried out in the potential range from − 0.5 V to + 0.8 V at scan rates of 5, 10, 20, 50, and 100 mV s⁻1 to evaluate the electron-transfer kinetics of the electrodes. Cyclic Voltammetry (CV) CV measurements were carried out in the potential range from − 0.5 V to + 0.8 V at scan rates of 5, 10, 20, 50, and 100 mV s⁻1 to evaluate the electron-transfer kinetics of the electrodes. Key Parameters MeasuredAnode open-circuit potential (OCP_anode)Cathode open-circuit potential (OCP_cathode)Individual electrode overpotentials at operating current densityCharge-transfer resistance (R_ct) obtained from Nyquist plots of electrochemical impedance spectroscopy Anode open-circuit potential (OCP_anode) Anode open-circuit potential (OCP_anode) Cathode open-circuit potential (OCP_cathode) Cathode open-circuit potential (OCP_cathode) Individual electrode overpotentials at operating current density Individual electrode overpotentials at operating current density Charge-transfer resistance (R_ct) obtained from Nyquist plots of electrochemical impedance spectroscopy Charge-transfer resistance (R_ct) obtained from Nyquist plots of electrochemical impedance spectroscopy Diffusion limitation verification To confirm that the BioBattery operates under non-diffusion-limited conditions, comparative experiments were performed under both static (quiescent) and stirred electrolyte environments.Static conditions: Static conditions: Static conditions: The BioBattery was immersed in 100 mM phosphate buffer (PPB) without any external agitation, allowing the electrochemical reactions to proceed under natural diffusion conditions.Stirred conditions: Stirred conditions: Stirred conditions: The electrolyte solution was continuously stirred at 300 rpm using a magnetic stirrer to enhance the transport of reactants and products to and from the electrode surfaces. For both experimental conditions, the power output of the BioBattery was measured across a range of external resistive loads. If the system were limited by diffusion processes, stirring would significantly enhance mass transport to the electrode surface, leading to a noticeable increase in power output. Therefore, comparison of the two conditions provides a direct verification of whether the device performance is influenced by diffusion limitations. Reference electrode specification All electrochemical measurements were performed using an Ag/AgCl reference electrode (3 M KCl, Metrohm, Switzerland). The measured potentials were converted to the Normal Hydrogen Electrode (NHE) scale using the following conversion relationship:2\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\text{E }}\left( {{\mathrm{vs}}.{\text{ NHE}}} \right) \, = {\text{ E }}\left( {{\mathrm{vs}}.{\text{ Ag}}/{\mathrm{AgCl}}} \right) \, + \, 0.{21}0{\text{ V }}\left( {{\text{at 25 }}^\circ {\mathrm{C}}} \right)$$\end{document} The reference electrode was calibrated against a freshly prepared hydrogen electrode prior to each set of measurements to ensure measurement accuracy and reproducibility. Results and discussion Comparative evaluation of anodic enzymes To experimentally substantiate the feasibility of the proposed enzymatic BioBattery architecture, a systematic comparative study was performed using three distinct multicopper oxidases: laccase derived from Trametes versicolor, BOD from Myrothecium verrucaria, and a McoP sourced from Pyrobaculum aerophilum. Each of these enzymes possesses the intrinsic ability to catalyze the oxidation of polyphenolic substrates, yielding electroactive quinone intermediates that serve as internal electron carriers. This enzymatic pathway enables in situ electron generation, thereby minimizing dependence on mass transport of external fuel molecules to the electrode surface. For anodic evaluation, all enzymes were immobilized onto GDEs with an effective diameter of 2 mm. To isolate the influence of anodic biocatalyst selection and ensure uniform cathodic performance across all experiments, each anodic configuration was paired with an identical arPES–BSA cathode, as schematically depicted in Figs. 2 and 3. Under these controlled conditions, the electrochemical performance of each BioBattery configuration was assessed, and the corresponding peak current density and power density values are compiled in Table 7.Fig. 2Power density–potential polarization curves of BioBattery configurations employing Laccase, BOD, and McoP as anodic biocatalysts immobilized on GDE electrodes (2 mm diameter). The cathode consisted of arPES–BSA blended with Ketjen black. Power density values were obtained from polarization measurements by varying the external resistance under identical experimental conditions.Fig. 3Current density–potential polarization curves corresponding to the BioBattery systems shown in Fig. 2 using Laccase, BOD, and McoP as anodic biocatalysts immobilized on GDE electrodes. The cathodic configuration consisted of arPES–BSA with Ketjen black conductive additive. Current densities were normalized to the geometric electrode area.Table 7Performance comparison of anodic enzymes immobilized on GDEs (paired with arPES–BSA cathode).Anodic enzymePeak power density (W/m2)Peak current density (A/m2)Laccase (T. versicolor)0.016 ± 0.0060.032 ± 0.008BOD (M. verrucaria)0.22 ± 0.030.48 ± 0.04McoP (P. aerophilum)0.45 ± 0.020.56 ± 0.08 Power density–potential polarization curves of BioBattery configurations employing Laccase, BOD, and McoP as anodic biocatalysts immobilized on GDE electrodes (2 mm diameter). The cathode consisted of arPES–BSA blended with Ketjen black. Power density values were obtained from polarization measurements by varying the external resistance under identical experimental conditions. Current density–potential polarization curves corresponding to the BioBattery systems shown in Fig. 2 using Laccase, BOD, and McoP as anodic biocatalysts immobilized on GDE electrodes. The cathodic configuration consisted of arPES–BSA with Ketjen black conductive additive. Current densities were normalized to the geometric electrode area. Table 7Performance comparison of anodic enzymes immobilized on GDEs (paired with arPES–BSA cathode).Anodic enzymePeak power density (W/m2)Peak current density (A/m2)Laccase (T. versicolor)0.016 ± 0.0060.032 ± 0.008BOD (M. verrucaria)0.22 ± 0.030.48 ± 0.04McoP (P. aerophilum)0.45 ± 0.020.56 ± 0.08 Performance comparison of anodic enzymes immobilized on GDEs (paired with arPES–BSA cathode). Among the enzymes tested, McoP exhibited the highest electrochemical performance, delivering nearly twofold higher power density than BOD and more than an order-of-magnitude improvement over laccase, making it the most suitable anodic biocatalyst. These findings are consistent with the polarization curves shown in Figs. 2 and 3. The superior performance of McoP as the anodic biocatalyst correlates with its higher specific activity (356 U/mg) compared to laccase (120 U/mg) and BOD (85 U/mg). However, the observed differences in electrochemical performance exceed what would be expected based solely on specific activity ratios. This suggests that additional factors contribute to the enhanced performance of McoP:Substrate specificity McoP demonstrates activity toward glutaraldehyde-derived polyphenolic structures, whereas the other enzymes show limited reactivity with this substrate.Redox potential compatibility The T1 copper site of McoP has a relatively low redox potential (~ 450 mV vs. NHE), facilitating electron transfer from the glutaraldehyde matrix.Thermostability McoP retains activity under the cross-linking conditions, whereas the other enzymes may experience partial denaturation. Substrate specificity McoP demonstrates activity toward glutaraldehyde-derived polyphenolic structures, whereas the other enzymes show limited reactivity with this substrate. Substrate specificity McoP demonstrates activity toward glutaraldehyde-derived polyphenolic structures, whereas the other enzymes show limited reactivity with this substrate. Redox potential compatibility The T1 copper site of McoP has a relatively low redox potential (~ 450 mV vs. NHE), facilitating electron transfer from the glutaraldehyde matrix. Redox potential compatibility The T1 copper site of McoP has a relatively low redox potential (~ 450 mV vs. NHE), facilitating electron transfer from the glutaraldehyde matrix. Thermostability McoP retains activity under the cross-linking conditions, whereas the other enzymes may experience partial denaturation. Thermostability McoP retains activity under the cross-linking conditions, whereas the other enzymes may experience partial denaturation. The correlation between specific activity and electrochemical performance is not linear, indicating that enzyme-electrode interactions and substrate accessibility play significant roles in determining overall BioBattery performance. Optimization of cathodic electrode composition Subsequently, the cathodic performance of the BioBattery was systematically optimized through a comparative evaluation of three distinct cathode formulations, namely laccase, BOD, and arPES–BSA. In all cases, the biocatalytic components were blended with Ketjen black to enhance electrical conductivity and electrode surface area, and each cathodic configuration was coupled with a multicopper oxidase from McoP–based anode. The electrochemical performance of the resulting systems was assessed in terms of peak power density and current density. A quantitative comparison of these metrics is summarized in Table 8, while the corresponding polarization and power density characteristics are illustrated in Figs. 4 and 5.Table 8Cathodic electrode performance paired with McoP anode.Cathodic materialPeak power density (W/m2)Peak current density (A/m2)Laccase + KB0.057 ± 0.0070.058 ± 0.009BOD + KB0.13 ± 0.020.38 ± 0.07arPES–BSA + KB0.46 ± 0.030.56 ± 0.05Fig. 4Power density–potential polarization curves comparing cathodic configurations employing Laccase, BOD, and arPES–BSA immobilized on Ketjen black modified electrodes. Each cathodic configuration was paired with an McoP-based enzymatic anode.Fig. 5Current density–potential polarization curves corresponding to the cathodic configurations shown in Fig. 4. Cathodes consisted of Laccase, BOD, or arPES–BSA mixed with Ketjen black and coupled with an McoP-modified anode. Current densities were normalized to the geometric electrode area. Table 8Cathodic electrode performance paired with McoP anode.Cathodic materialPeak power density (W/m2)Peak current density (A/m2)Laccase + KB0.057 ± 0.0070.058 ± 0.009BOD + KB0.13 ± 0.020.38 ± 0.07arPES–BSA + KB0.46 ± 0.030.56 ± 0.05 Cathodic electrode performance paired with McoP anode. Power density–potential polarization curves comparing cathodic configurations employing Laccase, BOD, and arPES–BSA immobilized on Ketjen black modified electrodes. Each cathodic configuration was paired with an McoP-based enzymatic anode. Current density–potential polarization curves corresponding to the cathodic configurations shown in Fig. 4. Cathodes consisted of Laccase, BOD, or arPES–BSA mixed with Ketjen black and coupled with an McoP-modified anode. Current densities were normalized to the geometric electrode area. arPES–BSA exhibited the highest output, likely due to the rapid electron transfer facilitated by the mediator. This combination of McoP/anode and arPES–BSA/cathode was selected for subsequent experiments. The observed high open-circuit voltage with the arPES–BSA cathode requires consideration of the redox potentials involved. While PES has a formal potential of approximately − 210 mV vs. NHE, which is more negative than the T1 copper sites of laccase (~ 780 mV) and BOD (~ 670 mV), the effective cathode potential is determined by the overall reaction kinetics and the overpotential for oxygen reduction. The arPES–BSA system demonstrates favorable kinetics for mediated electron transfer to oxygen, despite the thermodynamic potential difference. This apparent contradiction is resolved by considering that (i) the rate of electron transfer from reduced arPES to oxygen is rapid, and (ii) the overall cell voltage is determined by the difference between the anodic oxidation potential (glutaraldehyde matrix oxidation by McoP) and the effective cathodic reduction potential, which includes kinetic factors beyond the standard redox potentials of the individual components. Control experiments for cathode verification Control experiments for cathode verification Control experiments for cathode verification To verify the role of each component in the arPES–BSA cathode, control experiments were performed (n = 3 for each condition):BSA-only cathode No measurable power output (peak power density < 0.01 W/m2)Free PES (not covalently bound) Rapid mediator leaching, unstable performance (peak power density 0.08 ± 0.03 W/m2, declining by > 80% within 10 min)KB-only cathode Negligible activity (peak power density < 0.005 W/m2)Heat-inactivated arPES–BSA No electrochemical activity, confirming the requirement for active redox cycling BSA-only cathode No measurable power output (peak power density < 0.01 W/m2) BSA-only cathode No measurable power output (peak power density < 0.01 W/m2) Free PES (not covalently bound) Rapid mediator leaching, unstable performance (peak power density 0.08 ± 0.03 W/m2, declining by > 80% within 10 min) Free PES (not covalently bound) Rapid mediator leaching, unstable performance (peak power density 0.08 ± 0.03 W/m2, declining by > 80% within 10 min) KB-only cathode Negligible activity (peak power density < 0.005 W/m2) KB-only cathode Negligible activity (peak power density < 0.005 W/m2) Heat-inactivated arPES–BSA No electrochemical activity, confirming the requirement for active redox cycling Heat-inactivated arPES–BSA No electrochemical activity, confirming the requirement for active redox cycling These controls confirm that the observed cathodic current arises from the redox-active arPES mediator and not from the BSA scaffold or carbon support alone. Influence of anodic enzyme layer thickness To explore the effect of enzyme loading, McoP layers were varied from 1 to 3 layers on GDEs. Power and current densities, as shown in Figs. 6 and 7, indicate minimal performance variation, summarized in Table 9.Fig. 6Power density–potential polarization curves showing the effect of McoP loading on BioBattery performance. Anodes were prepared with one, two, and three McoP layers immobilized on GDE electrodes while maintaining the same cathodic configuration.Fig. 7Current density–potential polarization curves corresponding to the BioBattery systems with different McoP layer numbers (one, two, and three layers) immobilized on GDE electrodes.Table 9Effect of McoP anodic layer number on biofuel cell performance.Number of anodic layersPeak power density (W/m2)Peak voltage (mV)Peak current density (A/m2)1 layer0.25 ± 0.04250 ± 420.18 ± 0.042 layers0.23 ± 0.03141 ± 340.16 ± 0.033 layers0.28 ± 0.05265 ± 340.19 ± 0.03 Power density–potential polarization curves showing the effect of McoP loading on BioBattery performance. Anodes were prepared with one, two, and three McoP layers immobilized on GDE electrodes while maintaining the same cathodic configuration. Current density–potential polarization curves corresponding to the BioBattery systems with different McoP layer numbers (one, two, and three layers) immobilized on GDE electrodes. Table 9Effect of McoP anodic layer number on biofuel cell performance.Number of anodic layersPeak power density (W/m2)Peak voltage (mV)Peak current density (A/m2)1 layer0.25 ± 0.04250 ± 420.18 ± 0.042 layers0.23 ± 0.03141 ± 340.16 ± 0.033 layers0.28 ± 0.05265 ± 340.19 ± 0.03 Effect of McoP anodic layer number on biofuel cell performance. The limited difference across layers suggests that cathodic limitations and surface area constraints primarily govern system performance. Verification of non-diffusion-limited operation To experimentally evaluate whether the BioBattery performance is influenced by diffusion constraints, its electrochemical behavior was compared under both static and stirred electrolyte conditions. The obtained results are summarized in Table 10.Table 10Effect of stirring on BioBattery performance.ConditionPeak power density (W/m2)Peak current density (A/m2)OCV (mV)Relative change (%)Static (quiescent)0.45 ± 0.020.56 ± 0.08520 ± 15—Stirred (300 rpm)0.47 ± 0.030.58 ± 0.09525 ± 18 + 4.4 Table 10Effect of stirring on BioBattery performance.ConditionPeak power density (W/m2)Peak current density (A/m2)OCV (mV)Relative change (%)Static (quiescent)0.45 ± 0.020.56 ± 0.08520 ± 15—Stirred (300 rpm)0.47 ± 0.030.58 ± 0.09525 ± 18 + 4.4 Effect of stirring on BioBattery performance. The experimental results show only a minor difference between the static and stirred conditions, with the peak power density increasing by approximately 4.4% under stirring. This small variation indicates that the BioBattery operates under non-diffusion-limited conditions, as enhanced mass transport does not significantly improve device performance. In contrast, conventional enzymatic fuel cells that depend on the diffusion of externally supplied fuels typically exhibit a substantial improvement in performance—often in the range of 30–50% or more—when the electrolyte is stirred. The limited change observed in the present system therefore supports the effectiveness of the proposed BioBattery architecture. Specifically, the fuel source (glutaraldehyde matrix) is co-immobilized with the enzyme at the anode, enabling localized fuel availability and reducing dependence on external mass transport. This design feature decouples power generation from diffusion constraints and contributes to the stable and efficient operation of the BioBattery. Series and parallel cell configurations The scalability of the BioBattery was assessed by connecting cells in series and parallel, as shown in Figs. 8 and 9. Peak power, voltage, and current densities are presented in Table 11.Fig. 8Power density–potential polarization curves of BioBattery systems assembled in single-cell, double-cell, and triple-cell configurations to evaluate the effect of stacking on overall power generation.Fig. 9Current density–potential polarization curves corresponding to the stacked BioBattery configurations (single-cell, double-cell, and triple-cell) shown in Fig. 8.Table 11Effect of series and parallel stacking on BioBattery output.ConfigurationCellsPeak power density (W/m2)Peak voltage (mV)Peak current density (A/m2)Series10.27292–Series20.52324–Series30.91380–Parallel1––0.30Parallel2––0.64Parallel3––0.95 Power density–potential polarization curves of BioBattery systems assembled in single-cell, double-cell, and triple-cell configurations to evaluate the effect of stacking on overall power generation. Current density–potential polarization curves corresponding to the stacked BioBattery configurations (single-cell, double-cell, and triple-cell) shown in Fig. 8. Table 11Effect of series and parallel stacking on BioBattery output.ConfigurationCellsPeak power density (W/m2)Peak voltage (mV)Peak current density (A/m2)Series10.27292–Series20.52324–Series30.91380–Parallel1––0.30Parallel2––0.64Parallel3––0.95 Effect of series and parallel stacking on BioBattery output. Series stacking increases output voltage, while parallel stacking enhances current density, confirming the modular design’s scalability. Transition from gold disk to TCP electrodes Replacing GDEs with TCP electrodes significantly increased both power and current outputs due to enhanced surface area, as shown in Figs. 10 and 11 and summarized in Table 12.Fig. 10Power density–potential polarization curves comparing BioBattery performance using GDE and TCP as anodic electrode materials with McoP immobilized as the anodic biocatalyst.Fig. 11Current density–potential polarization curves corresponding to the BioBattery configurations shown in Fig. 10 using GDE and TCP electrodes.Table 12Performance enhancement with TCP electrodes.Electrode typePeak power density (W/m2)Peak current density (A/m2)GDE0.26 ± 0.020.64 ± 0.04TCP0.85 ± 0.050.89 ± 0.07 Power density–potential polarization curves comparing BioBattery performance using GDE and TCP as anodic electrode materials with McoP immobilized as the anodic biocatalyst. Current density–potential polarization curves corresponding to the BioBattery configurations shown in Fig. 10 using GDE and TCP electrodes. Table 12Performance enhancement with TCP electrodes.Electrode typePeak power density (W/m2)Peak current density (A/m2)GDE0.26 ± 0.020.64 ± 0.04TCP0.85 ± 0.050.89 ± 0.07 Performance enhancement with TCP electrodes. TCP electrodes enabled more efficient charge collection and higher current flow, as confirmed by capacitor charging experiments in Figs. 12 and 13, demonstrating reliable energy storage and release.Fig. 12Charge–discharge cycles of a 47 μF capacitor powered by the TCP-based BioBattery configuration, demonstrating repeated capacitor charging and discharging behavior.Fig. 13Charge–discharge cycles of a 470 μF capacitor driven by the optimized TCP-based BioBattery system, demonstrating stable and reproducible capacitor charging performance. Charge–discharge cycles of a 47 μF capacitor powered by the TCP-based BioBattery configuration, demonstrating repeated capacitor charging and discharging behavior. Charge–discharge cycles of a 470 μF capacitor driven by the optimized TCP-based BioBattery system, demonstrating stable and reproducible capacitor charging performance. Polarization and stability measurements The OCP of the McoP/anode and arPES–BSA/cathode pair remained stable for ~ 3200 s, illustrating system robustness. TCP-based BioBattery modules were successfully integrated with a BioCapacitor to power low-energy devices, demonstrating practical applicability. To evaluate the individual contributions of the electrodes to the overall BioBattery performance, three-electrode electrochemical measurements were performed. The obtained parameters are summarized in Table 13.Table 13Individual electrode potentials and overpotentials.ElectrodeOCP (mV vs. NHE)Operating potential (mV)Overpotential (mV)Rct (Ω)Dominant limitationAnode (McoP)120 ± 1580 ± 1040 ± 845 ± 5KineticCathode (arPES-BSA)650 ± 20580 ± 1570 ± 1268 ± 8Mixed kinetic / mass transport Table 13Individual electrode potentials and overpotentials.ElectrodeOCP (mV vs. NHE)Operating potential (mV)Overpotential (mV)Rct (Ω)Dominant limitationAnode (McoP)120 ± 1580 ± 1040 ± 845 ± 5KineticCathode (arPES-BSA)650 ± 20580 ± 1570 ± 1268 ± 8Mixed kinetic / mass transport Individual electrode potentials and overpotentials. The anode open-circuit potential of approximately 120 mV vs. NHE is consistent with the electrochemical oxidation of glutaraldehyde-derived polyphenolic structures. The relatively small anodic overpotential (40 mV) observed at the operating current density indicates favorable kinetics for the enzymatic oxidation process. In contrast, the cathode exhibits an open-circuit potential of approximately 650 mV vs. NHE, corresponding to the oxygen reduction reaction mediated by arPES. The larger cathodic overpotential (70 mV) suggests comparatively slower kinetics and partial mass-transport limitations. These results indicate that the cathode acts as the primary rate-limiting component of the BioBattery system. This observation is further supported by the improvement in overall device performance when the cathode surface area was increased using TCP electrodes. Implications and comparison with literature Compared to other enzymatic biofuel cells16,17, this system overcomes fuel diffusion limitations by embedding fuel in the anode, enabling miniaturization and enhanced integration for wearable and implantable devices. Figures 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12 and 13 collectively illustrate optimization of electrode materials, enzyme selection, and cell stacking, providing a complete framework for high-efficiency BioBattery design. Mechanistic justification for anodic MCO deployment The use of multicopper oxidases (MCOs) at the anode represents a departure from their conventional cathodic role. This reversal is enabled by exploiting the bidirectional nature of the enzymatic redox chemistry.Cathodic function (conventional) MCOs typically catalyze the four-electron reduction of oxygen (O₂) to water (H₂O), accepting electrons through the T1 copper site.Anodic function (this work) When provided with a suitable polyphenolic substrate, such as the glutaraldehyde-derived matrix used in this study, MCOs can oxidize the substrate. During this process, electrons are transferred to the T1 copper site and subsequently to the electrode. Cathodic function (conventional) MCOs typically catalyze the four-electron reduction of oxygen (O₂) to water (H₂O), accepting electrons through the T1 copper site. Cathodic function (conventional) MCOs typically catalyze the four-electron reduction of oxygen (O₂) to water (H₂O), accepting electrons through the T1 copper site. Anodic function (this work) When provided with a suitable polyphenolic substrate, such as the glutaraldehyde-derived matrix used in this study, MCOs can oxidize the substrate. During this process, electrons are transferred to the T1 copper site and subsequently to the electrode. Anodic function (this work) When provided with a suitable polyphenolic substrate, such as the glutaraldehyde-derived matrix used in this study, MCOs can oxidize the substrate. During this process, electrons are transferred to the T1 copper site and subsequently to the electrode. The glutaraldehyde cross-linking process creates a polymeric matrix with phenolic characteristics, which serves as the electron donor. The McoP enzyme, in particular, has demonstrated the ability to oxidize such structures, generating electroactive quinone intermediates that facilitate electron transfer to the anode. This proposed mechanism is supported by the following observations:The current output shows a dependence on the concentration of glutaraldehyde used during the cross-linking process.Control experiments with heat-inactivated McoP show no measurable current generation.Systems without glutaraldehyde cross-linking also exhibit negligible current output.A clear correlation is observed between polyphenol oxidase activity and the electrochemical performance of the BioBattery system. The current output shows a dependence on the concentration of glutaraldehyde used during the cross-linking process. The current output shows a dependence on the concentration of glutaraldehyde used during the cross-linking process. Control experiments with heat-inactivated McoP show no measurable current generation. Control experiments with heat-inactivated McoP show no measurable current generation. Systems without glutaraldehyde cross-linking also exhibit negligible current output. Systems without glutaraldehyde cross-linking also exhibit negligible current output. A clear correlation is observed between polyphenol oxidase activity and the electrochemical performance of the BioBattery system. A clear correlation is observed between polyphenol oxidase activity and the electrochemical performance of the BioBattery system. Limitations of the study Despite the promising performance of the proposed BioBattery system, several limitations should be acknowledged. The electrochemical characterization was conducted under controlled laboratory conditions, and system behavior in complex real-world or physiological environments may differ due to variations in temperature, pH, and oxygen availability. The long-term operational stability of the immobilized multi-enzyme system, particularly under continuous or cyclic loading, was not evaluated beyond the experimental timeframe of this study. In addition, while the internal confinement of the fuel reduces dependence on external substrate diffusion, the total energy output remains inherently limited by the finite quantity of immobilized reactants. Finally, further optimization of enzyme loading, electrode architecture, and integration strategies will be necessary to improve power density and extend operational lifetime for practical deployment. Conclusion The present work investigates the design, fabrication, and electrochemical characterization of an enzymatic fuel cell that employs a multicopper oxidase as the anodic biocatalyst. In contrast to conventional enzymatic fuel cell architectures that depend on continuous diffusion of substrates from the bulk environment to the electrode interface, the proposed system operates through a configuration in which the electroactive species are confined within the device. By reducing reliance on sustained external substrate transport, this approach seeks to mitigate a key limitation associated with diffusion-controlled enzymatic systems. The resulting architecture represents a step toward more integrated and self-contained enzymatic energy conversion platforms, here referred to as BioBatteries, with potential relevance for low-power and miniaturized electronic applications. In the BioBattery configuration, both the enzymatic catalyst and its corresponding fuel are immobilized at the anode, providing a battery-like operational mode. The cathodic reaction can utilize ambient electron acceptors, such as dissolved molecular oxygen, which is readily available in many physiological and environmental conditions. This design enhances operational autonomy under suitable conditions and may be advantageous in applications where continuous external fuel supply is impractical. Furthermore, the BioBattery is electrically coupled with a previously developed BioCapacitor to enable voltage amplification, thereby expanding the range of electronic components that can be powered within the limits of the present system. The primary objective of this study is to demonstrate the fabrication and electrochemical performance of a multi-enzyme system capable of oxidizing phenolic substrates. Enzyme immobilization is achieved via glutaraldehyde vapor deposition, which promotes enzyme confinement and functional stability at the electrode surface, although long-term stability beyond the tested duration remains to be fully evaluated. The resulting BioBattery is shown to power the BioCapacitor, enabling repeated charging of a 470 μF capacitor in under 25 s under the tested laboratory conditions. These results demonstrate the feasibility of the concept and its ability to deliver usable electrical energy to an auxiliary storage component, highlighting its potential as a bioelectrochemical power source while acknowledging that further optimization will be required for practical deployment. Despite the promising performance of the proposed BioBattery system, several limitations should be acknowledged. The electrochemical characterization was conducted under controlled laboratory conditions, and system behavior in complex real-world or physiological environments may differ due to variations in temperature, pH, and oxygen availability. The long-term operational stability of the immobilized multi-enzyme system, particularly under continuous or cyclic loading, was not evaluated beyond the experimental timeframe of this study. In addition, while the internal confinement of the fuel reduces dependence on external substrate diffusion, the total energy output remains inherently limited by the finite quantity of immobilized reactants. Finally, further optimization of enzyme loading, electrode architecture, and integration strategies will be necessary to improve power density and extend operational lifetime for practical deployment.