Oxypolymerization in the Manufacture of Bricks Based on Gold Mine Tailings and Cooking Oil as a Binder Authors: Alonso Rodrigo Zúñiga-Suárez, Liliana Alexandra Zúñiga-Torres, Francisco Hernández-Olivares, Berenice Cecibel Zúñiga-Torres, Guido Giuliano Gualpa-Guzmán, Jhon Patricio Rodriguez-Tapia Published: 2026 ABSTRACT This study presents the development of an eco-friendly brick for mining, a sustainable composite material manufactured from gold mine tailings and used cooking oil (UCO) through a thermal oxypolymerization process. Unlike conventional stabilization methods, which often require additional materials beyond tailings or have a high carbon footprint in their production, this approach uses oxypolymerization to transform these two waste products into novel building materials. The use of various percentages of UCO at different heating temperatures was evaluated to identify the optimal mixture, determining that a 9% UCO content and a 9 h cycle are key conditions for inducing fatty acid crosslinking. This logical relationship between heat treatment and dosage allows the organic binder to consolidate the mineral matrix, giving the material a compressive strength of 19.12 MPa and a flexural strength of 8.24 MPa, exceeding the thresholds of the NTE INEN 297 standard. The low water absorption (2.86%) is attributed to the densification of the matrix and the hydrophobic nature of the polymerized oil, indicators of its structural durability. This work is the first to use Ecuadorian tailings as the sole mineral aggregate, validating a high-efficiency, low-impact product for sustainable construction under the principles of the circular economy. 1. Introduction The construction industry is currently one of the largest consumers of natural resources globally, basing its model on the intensive use of non-renewable materials, which has precipitated a progressive depletion of the environment [1]. Faced with the growing scarcity of critical resources such as sand and gravel, industry stakeholders have begun to recognize the seriousness of the situation and the urgency of transitioning to more responsible models [2]. In this context, there is a growing interest in promoting sustainable development by integrating raw materials from industrial waste, applying them to the creation of new construction compounds to reduce pressure on natural ecosystems [3]. In particular, the recycling of massive waste, such as mining tailings, is presented as an indispensable strategy to alleviate the social and environmental problems arising from its accumulation [4]. The magnitude of this challenge becomes clear when analyzing the mining industry, which, as a pillar of economic growth representing 6.9% of global GDP [5,6], generates unprecedented volumes of waste. It is estimated that, since the mid-20th century, 190,000 tons of gold have been extracted [7], resulting in an annual tailings production ranging from 5 to 14 billion tons [8,9]. According to projections by Hudson et al. [10], the total volume of tailings and waste rock could reach 2 billion tons by 2050. These tailings cause numerous environmental and social impacts [11], with serious storage and management risks [12], soil degradation, reduction in groundwater, and air, water, and soil pollution [13,14,15]; they are stored as sludge in reservoirs [16,17], with increasing technical and sustainable management challenges [18,19]. Their disposal in landfills degrades the soil and contaminates the water [20,21] with high maintenance costs [22,23]; they constitute mixtures of waste with remnant metals and residual chemicals [24,25], whose collapse can be catastrophic [26], and their accumulation of cyanide, mercury, and arsenic represents a large environmental liability [27,28]. This problem is especially relevant in Ecuador, where the Portovelo mining canton is the oldest and most important gold-mining area in the country, with a historical production exceeding 4.5 million ounces of gold [29,30]; Portovelo houses the largest mining complex in Ecuador and South America, recognized as the first mining center and cultural heritage [31], and represents the fifth national export sector [32]. Although the country has a high potential for mineral resources due to its geographical relief, these have not been managed with a comprehensive sustainability vision [33]. A critical example is the El Tablón community tailings dam in Portovelo, which by 2019 already held more than 1.6 million m3 of tailings, with an annual generation of around 400,000 tons [34,35,36,37]. Unfortunately, the management of these wastes in the country remains deficient due to a lack of clear regulations, insufficient controls, and a lack of technical studies that would allow for their socialization and industrial utilization [38,39,40,41,42,43,44]. It is therefore imperative to promote practices that transform these liabilities into viable technical solutions [45]. Alongside mining waste, there is another domestic and commercial waste with a high polluting potential: used cooking oil (UCO). This by-product, resulting from cooking processes that alter its chemical and physical structure [46,47,48], represents a direct threat to the environment if it is not managed correctly [49,50,51,52], since a single liter of oil can render up to 1000 L of water unusable [52]. According to international data, Asia satisfies more than 54% of the world’s demand for vegetable oil; Indonesia is the world’s largest producer, followed by China, Malaysia, the United States, and Brazil [53]; likewise, these countries generate millions of tons of waste from this material, of which only a very small fraction is reused and properly treated [54]. It is estimated that up to 40% of consumed vegetable oil ends up as untreated waste [55,56], and in Ecuador, the situation is alarming, with 54% of citizens disposing of it in regular trash and 24% pouring it directly into the sewer system [57]. With only 4% recycling nationwide, the lack of effective policies for the management of used cooking oil, especially in cities like Loja, exacerbates the obstruction of sanitation systems and soil contamination [58]. Faced with these two environmental challenges, the circular economy emerges as an essential framework for managing industrial waste and by-products [59], prioritizing their recovery, reuse, and recycling [60,61,62], especially in mining, where volumes are massive [63,64,65], with the aim of keeping materials in the economy for as long as possible [66,67,68]. Reusing tailings as a raw material in construction has shown potential, although it poses logistical, regulatory, and infrastructure challenges [69], driving innovative solutions that reduce environmental impact and improve resource utilization [6,70]. In this regard, tailings rich in silica and alumina with pozzolanic properties improve mechanical strength and durability in bricks, concretes, ceramics, and paints [71,72,73]; as for used cooking oil (UCO), it has demonstrated high technical viability as a binder in the construction industry, based on the chemical process of oxypolymerization. This mechanism is activated by heating vegetable oil to a range of 160 to 200 °C, which triggers complex oxidation, polymerization, esterification, and polyesterification reactions [74,75]. These reactions transform the liquid state of the oil into a stable, solid binder that reacts in the layers coating the mineral aggregate particles, effectively binding them together according to the mass and temperature applied [76]. This transformation is the basic principle of so-called vegeblocks or materials bound with vegetable oil. Several previous studies have validated the effectiveness of this technology through specific applications. For example, Adebayo et al. manufactured wastevege blocks using sand and used cooking oil as a novel, renewable, and biodegradable binder in the production of building blocks [74]; Johnson et al. [76] obtained high compressive strengths by combining oils with petroleum sludge; Sosa et al. [77] produced lightweight ceramics with UCO that exceeded conventional strengths, confirming their viability in circular economy models, while Attia et al. [78] developed vegeblocks with recycled aggregates to reduce dependence on imported raw materials. Starón et al. [79,80,81] manufactured blocks using polymerization and esterification. Similarly, Forth et al. [82] produced masonry products such as blocks and bricks, and Nadeem et al. [83] produced sustainable roof tiles using waste oil as a substitute for clay and cement. Beyond the documented environmental benefits, the development of these materials can be enriched by observing the results achieved in other areas of mining engineering. For example, advanced studies in porous media have accurately modeled anisotropic non-Darcy seepage in natural fractures [84], while the stability of working faces has been analyzed using fold mutation theory [85]. Their analytical rigor serves as a benchmark for further understanding the microstructure and failure modes of new waste-based materials. Based on this background, and considering that in Ecuador, local raw materials present excellent properties for the design of ecological materials [86], the present research simultaneously addresses these two environmental challenges through the development of the eco mining brick, a sustainable construction material made exclusively with gold mine tailings and used cooking oil, under a thermal process of oxy-polymerization. Unlike previous research that uses used cooking oil with conventional aggregates or tailings with cementitious binders, this work uses gold tailings from the canton of Portovelo as the only mineral component, without the addition of cement or virgin materials. The study is developed in the following phases: (i) preparation and physical-chemical and mineralogical characterization of mine tailings and UCO as raw materials; (ii) determination of the optimal tailings/UCO mixture and oxy-polymerization temperature through experimental design; (iii) manufacture of eco mining brick prototypes and evaluation of their physical and mechanical properties (compressive strength and flexural strength) under Ecuadorian regulations. The innovation of this study lies in three differentiating aspects: the use of Ecuadorian gold tailings, a material not previously explored as an aggregate in oxy-polymerization processes; the evaluation of the synergistic effect of dosage and temperature on the material’s properties; and the validation of the product under regulatory standards applicable to construction. 2. Materials and Methods 2.1. Raw Materials 2.1.1. Gold Mine Tailings The tailings used as raw material were collected from a mining area in the southwest of Ecuador, in El Oro province, in Portovelo canton. The climate in Portovelo is subtropical to humid tropical, with average temperatures between 18 and 24 °C. Furthermore, due to its mountainous topography, it is characterized by high annual rainfall. The average altitude of the study area also varies considerably, from 600 to 3000 m above sea level. It is part of a mountainous region and is located within the western Andes mountain range (Figure 1). Gold mine tailings (MT) typically have a granular, earthy appearance and a predominantly light gray color. The material contains medium-sized fragments due to accumulation and agglomeration, as shown in Figure 2. 2.1.2. Used Cooking Oil Used cooking oil (UCO) was collected from a restaurant located in the southern Andean region of Ecuador, in the province Loja, in city of Loja,. From a chemical point of view, UCO is a complex mixture of fatty acids and mono-, di-, and triglycerides [75]. In terms of its physicochemical properties, UCO shows a notable degradation compared to virgin oil (Figure 3a); the frying process and prolonged storage cause a darkening towards brown tones (Figure 3b), in addition to an increase in viscosity and alterations in its molecular composition due to thermal saturation. 2.2. Research Methodology The methodology of this research is developed in three main phases, as illustrated in Figure 4. The first phase corresponds to the preparation and characterization of the raw materials; for this, the tailings from the Portovelo mine were oven-dried at 100 °C ± 5 °C to remove residual moisture and then sieved through a No. 40 mesh to homogenize the particle size, while the used cooking oil was filtered to remove impurities. Next, the physicochemical and mineralogical characterization of the materials was carried out: in the case of the oil, the moisture content [87], density [88], kinematic viscosity (BDV-9S, Biobase Biodustry Co., Ltd., Jinan, China) [89], and gas chromatography (Trace 1300, Thermo Fisher Scientific, Waltham, MA, USA) [90] were evaluated. Simultaneously, the tailings were analyzed using granulometry tests [91], specific gravity [92], and Atterberg limits [93], complementing the study with X-ray Fluorescence (XRF, Bruker S1, Bruker Corporation, Billerica, MA, USA) and X-ray Diffraction (XRD, Bruker D8, Bruker Corporation, MA, USA) techniques. Subsequently, the second phase focused on the design and determination of the optimal mixture. The experimental process began with the determination of the reference weight based on the volume of 5 cm edge cubes, which allowed for the precise establishment of the proportions of tailings and used cooking oil (UCO). For each combination, three specimens were prepared using oil concentrations of 7%, 9%, and 11%, parameters defined from previous research [74,79,80,83]. The mixture was produced by heating the UCO to stepped temperatures of 120 °C, 150 °C, 180 °C, 210 °C, 250 °C, and 280 °C, gradually incorporating the tailings until homogeneity was achieved, visually validated by the color change in the material from light to dark gray. Once this state was reached, the material was molded into three layers of equal thickness, applying a pressure of 680 kgf per layer using a hydraulic press to minimize voids and ensure the compactness of the structure. Following molding, a cooking protocol was executed using a temperature-controlled muffle furnace to ensure material stability. This thermal cycle began at room temperature, increasing at a rate of 1 °C/min until reaching 100 °C, where it was maintained for 8 h. Subsequently, the temperature was raised again at the same rate to 180 °C, a value that was held constant for all combinations for 6 h to facilitate thermal consolidation of the specimens. The process concluded with a gradual return to ambient temperature, specifically designed to avoid thermal shock that could compromise the structural integrity of the cubes before their removal. The results of this phase, evaluated under the standards of ASTM C109 [94], allowed the identification of a preliminary optimum mixture composed of 9% UCO at 180 °C. In order to enhance the strength achieved, combinations of 7%, 9%, and 11% UCO were redesigned, subjecting them to heating temperatures of 180 °C, 210 °C, 250 °C, and 280 °C, and extending the cooking time to 9 h at a cooking temperature of 180 °C (Table 1). In the third phase, the final prototypes of the material called eco-mining brick, measuring 125 mm wide, 250 mm long, and 75 mm thick, were manufactured and evaluated. The technical validity of this development was determined following the guidelines of the standard NTE INEN 294 [95], and its compressive strength was evaluated according to the Ecuadorian technical standard NTE INEN 297 [96]. This standard establishes that ceramic bricks must achieve a minimum compressive strength of 6 MPa, a parameter that ensures the viability of the material in the context of local construction. Flexural strength was also evaluated by fabricating beams with dimensions of 40 mm wide, 100 mm long, and 40 mm thick. These specimens were subjected to tests following the guidelines of standard NTE INEN 295 [97] and their results were validated using the Ecuadorian technical standard NTE INEN 297 [96]. This standard establishes a minimum flexural strength parameter of 4 MPa. Additionally, the physical absorption test was carried out applying what is established in the standard NTE INEN 296 [98] and validating that its result is within the ranges established by the standard NTE INEN 297 [96]. 3. Results and Discussion 3.1. Characterization of Used Cooking Oil (UCO) The characterization of used cooking oil (UCO) was carried out to evaluate the effect of its composition on its binding capacity performance (Table 2). The measured density of the UCO was 0.906 g/cm3, a value within the typical range reported for used vegetable oils, whose density ranges from 0.910 to 0.930 g/cm3 at temperatures between 15 °C and 25 °C [99]. Used cooking oils tend to be marginally lighter than fresh oils due to oxidation, polymerization, and triglyceride chain rupture processes that occur during repeated heating. This behavior is consistent with that reported by Kharshiduzzaman et al. [100], who obtained densities of approximately 0.889 g/cm3 in used cooking oil after multiple frying cycles, indicating that progressive thermal degradation slightly reduces the oil’s density. Similarly, Staron et al. [80] reported that used rapeseed oil, employed as a binder in construction blocks, had a density of 0.907 g/cm3, a value that closely corresponds to that obtained in the present study, suggesting that the analyzed UCO possesses suitable physicochemical properties to function as a binding agent in solid construction matrices. From the perspective of its use in construction materials, the density of UCO is significantly lower than that of water (1.0 g/cm3), which implies its ability to penetrate the pores of the mining tailings without generating considerable increases in mass in the final brick, thus favoring the strength-to-weight ratio of the material. Regarding moisture content, the recorded value was 0.14%, which can be considered low and favorable for the proposed construction application. High moisture content in the oil can cause hydrolysis and increase free fatty acids, making moisture removal essential to prevent oxidation and deterioration of the oil. This result is comparable to that reported by Darmawan et al. [101], who found that oils purified with activated carbon had water contents of 0.087 ± 0.171%, a value slightly lower than that obtained in this study, indicating that the analyzed UCO retains a moderate but controlled residual moisture. From the perspective of brick manufacturing, a low moisture content in the UCO is desirable because it minimizes the possibility of saponification or hydrolysis reactions with the components of the mining tailings, preserving the chemical integrity of the binder during the curing and consolidation process of the material. The dynamic viscosity of 20.5 cP and the kinematic viscosity of 22.63 cSt characterize UCO as a fluid of moderate viscosity at room temperature. The relationship between these two values is governed by the fluid’s density, since kinematic viscosity is the ratio of dynamic viscosity to density, a quantity in which no external force intervenes, which explains the mathematical consistency of the values obtained. Compared to the literature, unprocessed UCO exhibits significantly higher viscosities; S. Puhan et al. [102] reported that the viscosity of unprocessed used cooking oil, measured at 21 °C, can reach values of up to 72 mm2/s. The viscosity of 22.63 cSt recorded in this study suggests that the oil was subjected to repeated frying conditions with probable prior filtration, which reduced its content of particles and high molecular weight polymers. In this regard, Mójica et al. [103] reported that the viscosity of used vegetable oils reached an average of 61.5 cP, considerably higher than the value of fresh vegetable oil (32.6 cP), highlighting the effect of thermal deterioration on the oil’s rheology. The value of 20.5 cP obtained in the present study indicates an oil with moderate degradation, which is advantageous for its homogeneous mixing with the mining tailings during the brick-making process, since a moderate viscosity facilitates the uniform distribution of the UCO among the tailings particles, promoting better interparticle adhesion and, therefore, greater cohesion of the compacted material. Finally, viscosity was measured at 12 RPM using a rotational viscometer, a condition corresponding to a low shear rate, suitable for medium-viscosity fluids. Dynamic viscosity measures the resistance to flow within a liquid, and the rotational method is the standard for evaluating fluids with complex behavior [104]. Choosing this speed ensures that the measurement was performed under laminar flow conditions, reducing errors associated with turbulence or frictional heating. Overall, the characterization parameters of used cooking oil (UCO) demonstrate that it is a residue with stable and controlled properties, suitable for its valorization as a binder in construction materials. The use of used cooking oil as a binder in the construction industry represents a viable alternative from a circular economy perspective, as it allows for a reduction in the generation of waste that is difficult to biodegrade [100]. The density values, low moisture content, and moderate viscosity make UCO an ideal candidate to provide cohesion and potential water repellency to bricks made with mining tailings. On the other hand, the chromatographic characterization of used cooking oil (UCO) reveals a lipid profile dominated by four main compounds that concentrate more than 90% of the total composition, which is shown in Table 3. Oleic acid constitutes the major fraction at 40.56%, followed by trans-linolenic acid at 27.47%, palmitic acid at 21.28%, and stearic acid at 4.52%. A typical used vegetable oil contains approximately 40–45% oleic acid along with palmitic acid and other fatty acids such as palmitoleic acid (1.75%), a profile that is related to the values obtained in this study [105]. The high presence of trans fatty acids, linolelaidic acid (27.47%), and elaidic acid (1.70%), totaling approximately 29%, is the most significant finding from the perspective of residue characterization. Gas chromatography analysis has demonstrated that repeated heating of oils leads to a decrease in polyunsaturated fatty acids and the generation of linolelaidic acid, direct evidence of cumulative thermal degradation [106]. This data is critical for the research because it confirms that the used cooking oil (CCO) is an intensively used and irreversibly altered oil, ruling out its reuse in food and technically justifying its valorization as an industrial input in brick manufacturing. The total saturated fraction of palmitic acid (21.28%) with stearic acid (4.52%) and myristic acid (0.23%) reaches approximately 26%, which is relevant to the behavior of the UCO within the brick-tailings matrix. Long-chain saturated fatty acids, such as palmitic and stearic acids, have high melting points and low chemical reactivity, properties that favor their role as water-repellent agents and surface modifiers in construction materials, potentially contributing to reducing the water absorption of bricks made with mining tailings [107]. 3.2. Characterization of Mine Tailings (MT) The particle size analysis of the gold mine tailings used in this research reveals a predominantly sandy distribution, with 74.07% sand, 19.09% silt, and 6.84% clay. This composition is consistent with the typical nature of metallic tailings, which, according to the study, most frequently exhibit a sandy-silty texture, being predominantly silty sands composed of quartz and clay minerals [108]. The particle size distribution curve according to ASTM D 6913 [109], ASTM D 1140 [110], and ASTM D 422 [91] (Figure 5) shows a material with a relatively uniform gradation in the fine sand-silt range, which is characteristic of metallurgical beneficiation processes that subject the ore to intensive grinding. This behavior is documented by the Federal Highway Administration, which reports that mill tailings are generally very fine-grained materials, with a particle size distribution that varies from sand to silt-clay depending on the degree of processing required to recover the ore [111]. According to the Unified Soil Classification System (USCS), the tailings are classified as SM (silty sand), and according to the AASHTO system, as A-2-4. This classification is consistent with the results obtained by previous research that determined, using standard ASTM procedures, that gold mine tailings can be classified as silty sand (SM), being fine-grained, non-plastic materials composed of fine sands and silts [108,109,112]. Additionally, Hu et al. [113] confirmed that coarse copper and iron tailings are also classified as silty sand (SM) according to the USCS, based on their Atterberg limits and particle size distribution. The A-2-4 classification in the AASHTO system indicates a granular material with a low fine content, suggesting favorable physical characteristics for applications in construction materials. The Atterberg limits of the tailings indicated undetermined values for both the liquid and plastic limits, confirming the non-plastic nature of the material, attributable to the predominance of coarse particles over fine fractions. Tailings samples from gold mines have been reported as non-plastic materials, a behavior directly related to their mineralogical composition dominated by non-clay minerals, especially quartz [114]. The absence of plasticity is advantageous for using this tailing as a component in bricks, as it minimizes the risk of volumetric expansion or contraction in response to changes in humidity, which could compromise the structural integrity of the final product. The fineness modulus obtained was 1.131, a value lower than the standard range of 2 to 3 recommended for conventional sands, reflecting the predominantly fine nature of the tailings. The incorporation of gold mine tailings reduces the fineness modulus of the mixture, demonstrating the higher proportion of fine particles compared to conventional sands [115]. The relative density (RD) of the tailings is 2.651 g/cm3, a value entirely consistent with those reported in the literature for precious metal tailings. The relative density of milling tailings varies between 2.60 g/cm3 and 3.35 g/cm3 [116], with most being below 3.0 g/cm3, except for the iron ore tailings from the Federal Highway Administration [117]. This value is practically identical to that of quartz (2.65 g/cm3), suggesting a predominantly siliceous mineralogical composition, a common characteristic in gold tailings processed by flotation or cyanidation. The absorption percentage of 1.59% reflects low surface porosity of the particles, a favorable condition for brickmaking, since higher tailings contents can increase water absorption in the final product, negatively affecting its strength [115]. The summary of the characterization results obtained from the laboratory is shown in Table 4. 3.3. Chemical-Mineralogical Characterization MT X-ray fluorescence (XRF) analysis of the gold mine tailings shown in Table 5 reveals that SiO2 (63.2%) and Al2O3 (13.1%) are the dominant oxides in the chemical composition, a pattern consistent with that reported in the literature for this type of waste. Gold mine tailings are composed mainly of SiO2 and Al2O3, which is why they can be used as aluminosilicate precursors in the production of construction materials [118]. In particular, XRF characterization studies carried out on tailings from artisanal gold mines reported that SiO2 is the most abundant component, with values ranging from 52.2 to 77.3% by weight, accompanied by Al2O3, CaO, Fe2O3, and traces of K2O, MnO, and ZnO [119], a composition that is closely similar to the values obtained in the present study. The sum of the oxides SiO2 + Al2O3 + Fe2O3 in the tailings analyzed reaches approximately 81.8%, a value that exceeds the minimum threshold required for a material to be considered pozzolanic. According to international standards, material with a minimum Al2O3 + Fe2O3 + SiO2 content greater than 70% by mass is suitable as a potential pozzolanic material, with SiO2 being the essential element for both pozzolanic properties and hydraulic reactivity [62]. The low content of CaO (1.88%) identified in the tailings is also a typical characteristic of gold tailings. The geochemical characterization of tailings from four gold mines in Egypt confirmed that the three dominant oxides are SiO2, Fe2O3, and Al2O3, with CaO and K2O contents varying according to the local geology of the deposit [120]. Elements such as S (1.28%), Zn (0.31%), and Mn (0.23%) require consideration from an environmental perspective. Gold mine tailings have a granitic composition enriched in potentially toxic elements such as Cu, Cd, Zn, Pb, As, and Cr, whose presence must be carefully evaluated when proposing their use as an alternative raw material in construction materials [121]. However, incorporating the tailings into the solid matrix of bricks, in combination with used cooking oil, could contribute to the immobilization of these trace elements, reducing their environmental mobility and simultaneously contributing to the valorization of two waste products under a circular economy approach [122]. The mineralogical analysis of the mine tailings using X-ray diffraction (XRD) is shown in Figure 6, which revealed the presence of four main crystalline phases: quartz (Q), muscovite (Mu), chamosite (Ch), and pyrite (P). Quartz was the dominant phase, with a high-intensity peak around 2θ = 26–27°, followed by secondary peaks distributed throughout the diffractogram. This mineralogical profile is consistent with that reported in the literature for tailings of metallurgical origin. The primary mineralogy of fresh tailings in porphyry-type deposits is commonly controlled by hydrothermal alteration processes and generally consists of quartz, pyrite, and muscovite (sericite) as the predominant phases. Similarly, tailings from gold mining in Brazil have been reported to consist mainly of quartz, iron oxides, and phyllosilicates such as muscovite and chlorite, with well-preserved sulfides in the form of iron sulfides [123]. The presence of chamosite in the tailings material is mineralogically significant. Chamosite is the ferrous member of the chlorite group, a hydrated aluminum-iron silicate that forms in low- to moderate-grade metamorphic environments and occurs primarily in iron ore deposits as genetic indicators of hydrothermal alteration. Pyrite, identified by low-intensity peaks, is a sulfide phase whose presence in tailings is of particular environmental and technological importance [124]. In the context of brickmaking with tailings, the low concentration of pyrite observed in the diffractogram, reflected in the low intensity of its peaks, is favorable, since its oxidation in construction materials can compromise structural durability [125]. 3.4. Determination of Optimal Mixture 3.4.1. Compressive Strength UCO Effect vs. Temperature The experimental design for selecting the optimal mix in construction materials incorporating used cooking oil (UCO) requires rigorous statistical methods. Analysis of variance (ANOVA) is the standard statistical tool for evaluating differences between multiple experimental groups, allowing us to determine whether the controlled factors—percentage of UCO, preparation temperature, and cooking time—have statistically significant effects on compressive strength. The optimal mix was determined by meeting the compressive strength requirements established in the standard NTE INEN 296 [98], as measured on cubic specimens. For each mix, three cubes were manufactured (50 mm × 50 mm), and their compressive strength was determined. Table 6 presents the organized results of the first experimental combinations. Eighteen combinations were evaluated, resulting from the factorial arrangement of three UCO levels and six cooking temperatures, with a constant cooking time of 6 h. To improve the results obtained, new combinations were developed with a cooking time of 9 h, starting at a temperature of 180 °C. These specimens were tested using a compression strength test (Table 7). Figure 7 shows the compressive strength behavior as a function of cooking temperature (6 and 9 h) for the three UCO concentrations. The peak strength at 180 °C is clearly visible, with the maximum value recorded at 9% UCO after 9 h of cooking; this combination was selected as optimal. The reference line indicates the compressive strength limit established by the standard NTE INEN 297 [96]. Figure 8 shows the ANOVA analysis of the box plots for each temperature level evaluated at 9 h of firing; this analysis reveals that temperature exerts a statistically significant influence on compressive strength (F = 8.84; p < 0.01). This finding contrasts with the results obtained at shorter times or with other factors, such as UCO content, positioning temperature as the main design parameter for optimizing the material’s strength capacity in prolonged curing or firing processes. 3.4.2. Characterization Microstructural Microstructural analysis using scanning electron microscopy (SEM) of the optimal mixture indicated a heterogeneous granular matrix composed predominantly of angular to subangular particles, with varying sizes resulting from the prior crushing process of the original material. This morphology is consistent with that reported by other researchers in mining tailings intended for the manufacture of construction materials, such as Pan et al. [126]. This angularity of the particles constitutes a structural advantage, as it promotes mechanical interlocking between grains and contributes to the matrix of the tailings-derived brick. Figure 9 shows that the dominant phase identified in the EDS spectra corresponds to quartz (SiO2), the major mineral in the tailings, whose angular morphology is consistent with its high hardness. Zhong et al. [127] demonstrated that in high-strength ceramic slabs made from tailings, quartz promotes the formation of liquid phases during sintering, filling micropores and improving matrix density [128]. In the same way, Figure 10 shows the presence of the mineral chamosite, a phyllosilicate mineral from the iron-rich chlorite group, formed by the association of the elements O–Si–Al–Fe–Mg. The identification of this phyllosilicate suggests that the tailings preserve minerals of hydrothermal or metamorphic alteration. The oxidation of ferrous iron (Fe2+) to ferric iron (Fe3+) during heating processes can generate significant mineralogical changes that affect the material’s chemical stability. The presence of chamosite in the optimal mix imposes temperature conditions that must account for the potential oxidative transformation of iron, improving the mechanical properties and density (pore sealing) of the prototype [129]. Muscovite, identified by dominant peaks of O, Si, and Al, accompanied by K, characteristic of potassium micas, is shown in Figure 11. This mineral occurs as fine, lamellar aggregates within the matrix. The coexistence of quartz and muscovite as major phases has been widely reported in ceramic systems derived from metamorphic and industrial rocks [130]. In the tailings brick, muscovite acts as an agent that regulates the plasticity of the fresh mix, and once fired, participates in the formation of secondary phases that contribute to matrix cohesion [129]. Figure 12 shows the texture of the optimum mixture (OM), which exhibits a relatively compact matrix distribution with intergranular pores of varying sizes. This observation is consistent with findings from studies incorporating waste cooking oil into construction materials: the oil generates organic deposits detectable by SEM, and at high concentrations, these deposits increase the macropore content in the paste, directly impacting the material’s mechanical strength and capillary absorption [131]. Similarly, the carbonaceous accumulations observed in the micrograph represent the organic residue of the used cooking oil. Research on composite materials using waste cooking oil as a binder indicates that the production technology for these materials is relatively simple, and that the oil generates a polymerization process upon heating, resulting in the bonding of aggregate particles and constituting a viable cohesive mechanism for construction materials [81]. 3.5. Eco Mining Brick Prototype The developed prototype, called the eco mining brick, represents an innovation in materials science by integrating two critical environmental liabilities: gold mine tailings and used cooking oil (UCO). Through an optimal mixture with 9% UCO, subjected to a molding pressure of 680 kgf and a heat treatment of 180 °C for 9 h, a material was obtained whose internal structure benefits from the polymerization of the oil as a hydrophobic binder [132] (Figure 13). The mechanical performance of the eco mining brick was validated according to the parameters of the Ecuadorian standard [NTE INEN 297 [96]. The compressive strength test, performed according to the NTE INEN 294 standard [95], indicates that the brick achieved a compressive strength of 19.12 MPa. This result exceeds the 6 MPa limit required for structural bricks by 282%. When comparing these findings with previous research, it is observed that authors such as Wei et al. [4] achieved a compressive strength of 22.37 MPa using tailings and clay; Umar et al. [133] obtained a compressive strength of 10.23 MPa using tailings and cement in a 1:1 ratio; and Mendonça et al. [134] reported strengths of 13.3 ± 2.55 MPa incorporating Portland cement. The distinctive advantage of the present research lies in achieving high-range mechanical properties by completely eliminating the use of conventional binders or natural clays, relying exclusively on the heat setting of residual oil in mining tailings. In this way, the incorporation of (UCO) modifies the microstructure of the tailings through the interaction of its components; the saturated fatty acids (palmitic, stearic, and myristic) act as water-repellent agents. Their linear structure allows for dense packing, reducing surface energy and capillary water absorption. Meanwhile, the unsaturated fraction (oleic, linolelaidic, palmitoleic, and elaidic) provides cohesion through auto-oxidation processes catalyzed by the tailings oxides, creating an organic network that improves mechanical resilience and micropore sealing. At a chemical level, the affinity of the carboxyl groups (-COOH) present in these seven acids for the mineral surfaces of the tailings facilitates the formation of a stable interface through chemisorption. This mechanism optimizes the structural strength of the brick. Additionally, the flexural strength analysis performed according to NTE INEN 295 [97] and the water absorption analysis performed according to [NTE INEN 296 [98] confirm the material’s suitability for civil construction (Table 8). The prototype registered a flexural strength of 8.24 MPa, doubling the standard requirement of 4 MPa, suggesting superior internal cohesion compared to handmade bricks. However, it is in the absorption property where the eco mining brick demonstrates its technical superiority, with a value of 2.86%, below the maximum permitted limit of 16%. This low porosity, attributed to the matrix densified by the polymerization of the UCO, is significantly lower than the 8–12% values reported by Pandey et al. [135] for fly ash bricks. This hydrophobic behavior not only guarantees greater durability against water erosion but also certifies that the material is fully suitable for application in structural and non-structural masonry. From an economic perspective, the unit production cost is estimated at USD 0.40, a highly competitive figure compared to traditional masonry units (USD 0.35) or bricks made using geopolymerization (USD 0.70), thus guaranteeing its technical and financial viability for sustainable construction projects in communities near mining areas. 4. Conclusions The technical feasibility of transforming two critical environmental liabilities, gold mining tailings and used cooking oil (UCO), into a new sustainable building material called eco-mining brick was demonstrated. This approach eliminates the need for conventional binders such as cement or lime, promoting a circular economy model in the construction sector. Through experimental design and analysis of variance (ANOVA), it was determined that the optimal mixture consists of 9% used cooking oil with a molding pressure of 680 kgf. The oxypolymerization process reached its maximum mechanical performance after a cooking time of 9 h at 180 °C, identifying temperature as the most influential design factor in the final strength. The final prototypes significantly exceeded the requirements of the Ecuadorian technical standard NTE INEN 297 [96]. A compressive strength of 19.12 MPa was achieved (compared to the minimum of 6 MPa required), and a flexural strength of 8.24 MPa (exceeding the minimum of 4 MPa), validating their suitability for structural and masonry applications. Scanning electron microscopy (SEM) analysis confirmed that the oil acts as an effective binder through the formation of organic deposits and polymerization processes that bind together the angular quartz and phyllosilicate particles of the tailings. The presence of saturated fatty acids in the UCO potentially contributes to the chemical stability and reduced water absorption of the brick. This work represents the first evaluation of gold tailings from the Portovelo area (Ecuador) as a single aggregate in oxypolymerization processes. The research not only offers a technical solution for the management of massive mining waste but also provides a material with low environmental impact and superior mechanical properties compared to traditional materials. 5. Future Lines of Research The analysis should be extended to temperate or polar climate regions, where freeze–thaw cycles act as a critical degradation factor. Evaluating the material’s resistance to the volumetric expansion of water and the resulting thermal fatigue would validate its technical viability and competitiveness in international markets with extreme climatic conditions.