Experimental investigation of novel 18 multiturn multiplane pulsating heat pipe for methanol Authors: N. Narendra Babu, G. S. V. L. Narasimham, P. Srikrishna Published: 2026 ABSTRACT A Pulsating Heat Pipe (PHP) is a wickless meandering capillary tube bent back and forth parallel to itself. In the present work, the possibility of employing a multiturn PHP as a pin-finned heat sink attached to a base plate is considered. Hence all the regions, other than those belonging to evaporators, function as condenser zones. Experimental investigations are carried on PHPs with multiturn, single plane and multiplane configurations. The condenser (or fin portions) of the PHPs is cooled by forced air flow and radiation to the surroundings. Experimental parametric runs are conducted by varying the fill ratio, orientations, and heat loads. Working fluid namely methanol is tested. PHP with 18 turns are tested for fill ratios of 30%, 50% and 70% and five orientations (+ 90°, + 45°, 0°, − 45° and − 90° measured with respect to horizontal). Heat loads are increased in steps of 50 W from 50 to 400 W for testing the PHPs. For different PHP physical geometries, the flow regimes change with respect to heat loads. The optimum angle for best thermal resistance is found to lie between 60 and 70°. Orientation independent operation observed in all the multiplane models and generally, the bottom heating mode (+ 90°) produce the highest heat transfer. During the startup, for lower heat loads, a temperature overshoot is observed before the establishment of pulsations. At higher heat loads, pulsations are set up without appreciable temperature overshoot, following a smooth startup. The results have shown enhancement in fin thermal conductivity compared to solid copper. The average thermal resistances \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${R}_{th}\left(^\circ{\rm C} /W\right)$$\end{document} for 18 multiplane is 0.3408 compare to dry fin thermal resistance \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${R}_{dry}$$\end{document} \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left(0.45^\circ{\rm C} /W\right)$$\end{document} shows its improvement in performance. Introduction The Pulsating Heat Pipe (PHP) is a passive device which means a device capable of working without the aid of any additional mechanical or electrical power input and hence has a long life span. The working of a conventional heat pipe depends upon the capillary action of a wick, however, the tubing used for PHPs is usually of such small diameter that insertion of a wick becomes impractical. A PHP is a promising two-phase heat transfer device to control heat fluxes1. It is also a complex heat transfer device with strong thermo-hydraulics influencing its performance2. A PHP operates through non-equilibrium two-phase oscillations driven by vapor pressure fluctuations. The success of the device mainly depends on the continuous maintenance or sustenance of these non-equilibrium conditions within the system. Studies have been carried out exclusively towards understanding the flow regimes3. PHPs are classified into single and multiturn, closed-loop and open-loop. A single loop PHP can be thought of as a building block for multiturn, single plane or multiplane PHPs. The term “capillary” means that the diameter of the tube is small enough for surface tension effect to become prominent4. A PHP contains evaporator, adiabatic and condenser zones. A pulsating heat pipe (PHP) is a wickless meandering capillary tube bent back and forth parallel to itself into many turns (single or multi-turn), These capillary tubes are evacuated initially and partially filled5. When a capillary tube is partially filled, the working fluid will break into liquid slugs and vapour plugs, provided the Bond number criterion is satisfied. Variation in the size of the channels produces variation in the pressure inside the container tubes6. The channel containing the two-phase working fluid with heated portion is referred to as the evaporator and the heat rejection portion is called the condenser7. The externally insulated region between the evaporator and condenser is called the adiabatic region8. The tube is filled with a working fluid such that only the fluid and its vapour phase exist. Pulsating type physical behaviour is possible for a particular range of diameters. The diameter should satisfy the relation Bo ≤ 2, where Bo is the Bond number. The diameter satisfying the Bond number criterion is termed the critical diameter. Bond numbers less than 2 promote the formation of vapour bubbles and liquid slugs9. A series of alternate bubbles and slugs can more easily produce pulsations upon the application of heat to the evaporator. With diameters larger than critical, it is not possible to produce oscillatory motion of the bubbles and slugs, and this leads to decreased effectiveness of the PHP performance. The critical diameter changes slightly with temperature since the properties of the working fluid depend upon the temperature10. Under microgravity conditions or where gravity has no component along the axis of the PHP tube, the required diameter is governed by the Weber number criterion. This is obtained by equating the surface energy of the slug \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$2\sigma /d$$\end{document} with the kinetic energy of the liquid slug \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$(1/2){\varrho }_{l}{V}^{2}$$\end{document} resulting in the relation\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\mathrm{We}\equiv \left({\varrho }_{l}{V}^{2}d\right)/\sigma \le 4 \mathrm{or} \equiv d\le \left(4\sigma \right)/\left({\varrho }_{l}{V}^{2}\right).$$\end{document} Sharp corners and edges in the channel are to be minimized as much as possible, as this affects normal slug flow in the PHP and tends to change the flow to stratified or annular flow regime. In stratified flow, the fluid flow will not be pulsatile. Also, the gravity driven thermosyphon effect domination leads to fall in heat transfer capability. Hence generally circular cross-sections are preferred for PHP applications11. Pulsating heat pipes can be classified with respect to various parameters like form factor, spatial orientation of the channels and type of end connection. Mainly there are two types of PHPs; the looped PHP, which has two open ends connected to one another, and the unlooped PHP12, which has two unconnected ends. The number of turns will affect thermal performance by varying the perturbations in each turn. This disturbance in pressure drives the oscillating flow of PHP. As per the literature, a PHP with smaller number of turns will not operate in the top heat modes or horizontal position. Compared to an open loop PHP, a closed loop PHP configuration is likely to get more oscillations because of the possibility of alternate circulations of the working fluid. It may be recalled that the inclination of the PHP varies from Bottom Heat Mode (BHM) to Top Heat Mode (THM). As per the literature, pulsations generally occur from BHM to horizontal position. Therefore, the inclination should be chosen such that it is in the range + 90°to 0°. For fixed temperatures of the evaporator and condenser, their heat transfer capacities depend upon their heat transfer areas13. At low heat flux inputs to evaporator, the fluid may not attain oscillations. On the other hand, for too high a heat flux input to the evaporator, there is the likelihood of dry-out. The PHP involves several geometrical parameters like condenser length \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${(L}_{co})$$\end{document} and evaporator length \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$({L}_{ev})$$\end{document}, number of turns \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${(N}_{t})$$\end{document}, tube diameter (outer/ inner), orientation (gravity angle) and characteristics of the tube material (thickness, density, thermal conductivity, surface roughness and specific heat). In this work a copper tube with an inner diameter of 2 mm is selected with working fluid methanol. In this case 2 mm diameter is slightly more than the critical value but not too far from satisfying the Bond number restriction. Working of a pulsating heat pipe (PHP) Heat is supplied to the device in the evaporator portion. Liquid in the form of liquid slugs or liquid film on the internal surface of the evaporator portion evaporates forming a vapour plug or bubble. Due to the increase in specific volume, the vapour plug expands and reaches the condenser portion, pushing the train of slugs and plugs ahead. In the condenser, the vapour volume reduces, and the pressure falls as the vapour transforms into liquid14. The pressure force now acts in the opposite direction, sending the slug-plug train back into the evaporator, wherein the liquid in the slugs or in the liquid film adhering to the wall evaporates creating a higher pressure. In this manner heat is transported from evaporator to condenser in an oscillatory or pulsating phenomenon. Hence the device is called an oscillating or pulsating heat pipe15. For fluid parcels moving between the evaporator and the condenser, if the PHP as a whole is taken as a constant total volume system, state that the overall change in the quality (or dryness fraction) is very small. Fluid selection and working properties for PHP The following are the important factors to be considered while selecting the operating fluid in PHP. Larger surface tension enables formation of slugs and plugs even in larger diameter tubes employed for PHPs. In wick-type heat pipes, large surface tension, wettability and low viscosity lead to good pumping action of fluid. Higher latent heat of vapourization results in high liquid conductance and high axial heat transfer. Meting point and critical point should not cross over the operating temperature of the fluid. When the operating range is within these limits, it is possible to obtain high heat transport with a small temperature difference in a PHP. Compatibility and corrosion resistance of the materials and chemical stability, toxicity and flammability of the working fluids are also important factors16. This device supports the possibility to use environmentally safe working fluids. Pressure drop, contact angle and liquid film thickness are important factors governing the working and improvement of the device. When the capillary tubes are initially evacuated and then partially filled with the working fluid, a train of liquid slugs and vapour plugs is formed inside the PHP3. Differential pressure created in a PHP due to differential heating and cooling between the evaporator and condenser acts as the driving force for producing momentum changes and oscillations in the two-phase fluid. This two-phase oscillatory flow causes efficient heat transmission from evaporator to condenser with very low temperature difference. The ratio of the volume of the fluid inside the PHP to the total volume is called the fill ratio17. It is widely accepted that the best working occurs in the range of 30% to 70% of the fill ratio. If the fill ratio is less than 20%, due to less liquid, dry-out occurs more readily at the evaporator and if the fill ratio is greater than 80%, the resulting lower degree of freedom may prevent pulsations. Reviews report that PHPs do not operate for higher charging ratios. A PHP is an efficient heat transportation device and is used in a variety of applications in thermal systems. An effective thermal conductance of over \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$1.5\times {10}^{4}$$\end{document} W/m.K is achievable with PHPs. Asymmetry in heating and deployment of valves can promote unidirectional circulation. Use of nano fluids can also increase heat transfer coefficient. Ultrasonic excitation will increase the pulsation amplitude and heat transfer coefficient. The mode of working depends on the location (orientation) of evaporator and condenser. Bottom Heat Mode (BHM) refers to evaporator below the condenser and the Top Heat Mode (THM) refers to condenser below the evaporator. If the PHP ends are closed at the extreme end points, then it is termed as an Open Loop PHP (OLPHP)18. If both ends are closed the PHP is termed as closed loop PHP (CLPHP). A CLPHP can also be used with check valves. The closed loop PHPs are found to be more efficient than the open loop PHPs. For heat abstraction at the condenser, both water cooling and air cooling methodologies can be adopted. Experimental work Constructional details for three-plane, 18-turn PHP Parametric studies are carried out with various working fluids, fill ratios and orientations. In particular, multi-plane PHP of 18 turns is constructed. The PHP is instrumented to obtain both pressure and temperature data at different locations of the system. In addition, the fin tip and root temperatures are monitored in multi-plane configuration. A study of the start-up characteristics of the PHP is also carried out. The reason behind varying the orientation with multi-plane, PHP is not only to examine the response to change in gravity but also to see if gravity-independent performance can be obtained. Copper tube of outer diameter 3 mm and inner diameter 2 mm is bent back and forth to form 18 turns in three parallel planes (i.e. multiplane, multiturn PHP), the bend radius being 7.5 mm. Two 3-way stop cocks, and a pressure transducer are fitted to the models. One stop clock is for evacuating the system and the other is for charging the working fluid. The vacuumizing and charging port combination features ball valves for their operation. The U-bends of the evaporator are brazed to a bottom copper plate. Cleaning of the PHP during fabrication stage is important to promote wetting of the walls with working fluid and capillary action19. After removing the solid particles from the inner tube, it is cleaned with a chlorinated solvent (trichloro-ethane) and an alkaline solution (sodium hydroxide) for removal of oily substances. Finally, the tube is rinsed with water or methanol for a small amount of time after the valves and ports are fixed. Different constructed views of multi-plane eighteen (18) multi-turn PHP is as shown in Figs. 1, 2, 3, and 4. The thermo-couple for temperature and pressure transducer (sensor) for pressure measurement locations are shown in Fig. 2. Summary of the geometric details is listed below in Table 1. Multiturn (18) means eighteen (18) turns in the evaporator of the PHP system.Fig. 1Different orientations of three-plane, 18-turn PHP.Fig. 2Thermo-couple locations of three-plane, 18-turn PHP.Fig. 3Actual views of three-plane, 18-turn PHP.Fig. 4Isometric view of three-plane, 18-turn PHP.Table 1Summary of the geometric details of multiplane (3), multiturn (18) PHP.ParameterNotationValueTotal vertical tubing length (mm)\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${L}_{v}$$\end{document}3936.4Horizontal tubing length (mm)\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${L}_{h}$$\end{document}115Bend radius (mm)\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$R$$\end{document}7.5Curved length of the bend (mm)\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\pi R$$\end{document}23.56Straight length in bend (mm)\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$l$$\end{document}5Net length in bend (mm)\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${l}_{b}=l+\pi R$$\end{document}28.56Number of bends in evaporator\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${n}_{e}$$\end{document}18Number of bends in condenser\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${n}_{c}$$\end{document}17Length of the tubing in bend (mm)\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${{L}_{b}=l}_{b}\times \left({n}_{e}+{n}_{c}\right)$$\end{document}999.67Total tubing length (mm)\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${L=(L}_{b}+{L}_{v}+{L}_{h} )$$\end{document}5051.07Internal diameter of the tubing\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${D}_{i}$$\end{document}2Cross-sectional area of the tubing (mm2)\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${A}_{c}=\pi {D}_{i}^{2}/4$$\end{document}3.14Total internal volume (mm3)\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${V}_{t}={A}_{c}\times L$$\end{document}15,868.4Total internal volume (ml)\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${V}_{t}$$\end{document}15.87Internal volume of pressure transducer (ml)\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${V}_{trans}$$\end{document}0.2Internal volume of the valve (ml)\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${V}_{val}$$\end{document}0.3Length of the adaptor hole (mm)\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$b$$\end{document}8.5Length of the valve/transducer inside adaptor (mm)\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$a$$\end{document}6Diameter of the adaptor (inner side) (mm)\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${d}_{i}$$\end{document}8.5Volume trapped inside the adaptor (mm3)\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${V}_{adap}=\pi \times {d}_{i}^{2}\times \left(b-a\right)$$\end{document}567.45Volume trapped inside 2 adaptors (ml)\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${V}_{trap}=2\times {V}_{adap}$$\end{document}1.13\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${{\boldsymbol{V}}}_{{\boldsymbol{m}}{\boldsymbol{i}}{\boldsymbol{s}}}={{\boldsymbol{V}}}_{{\boldsymbol{t}}{\boldsymbol{r}}{\boldsymbol{a}}{\boldsymbol{n}}{\boldsymbol{s}}}+{{\boldsymbol{V}}}_{{\boldsymbol{v}}{\boldsymbol{a}}{\boldsymbol{l}}}+{{\boldsymbol{V}}}_{{\boldsymbol{t}}{\boldsymbol{r}}{\boldsymbol{a}}{\boldsymbol{p}}}$$\end{document}Volume to be charged of 30% (ml)\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${V=0.3V}_{t}+{V}_{mis}$$\end{document}6.4Volume to be charged of 50% (ml)\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${V=0.5V}_{t}+{V}_{mis}$$\end{document}9.6Volume to be charged of 70% (ml)\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${V=0.7V}_{t}+{V}_{mis}$$\end{document}12.7 Different orientations of three-plane, 18-turn PHP. Thermo-couple locations of three-plane, 18-turn PHP. Actual views of three-plane, 18-turn PHP. Isometric view of three-plane, 18-turn PHP. Table 1Summary of the geometric details of multiplane (3), multiturn (18) PHP.ParameterNotationValueTotal vertical tubing length (mm)\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${L}_{v}$$\end{document}3936.4Horizontal tubing length (mm)\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${L}_{h}$$\end{document}115Bend radius (mm)\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$R$$\end{document}7.5Curved length of the bend (mm)\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\pi R$$\end{document}23.56Straight length in bend (mm)\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$l$$\end{document}5Net length in bend (mm)\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${l}_{b}=l+\pi R$$\end{document}28.56Number of bends in evaporator\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${n}_{e}$$\end{document}18Number of bends in condenser\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${n}_{c}$$\end{document}17Length of the tubing in bend (mm)\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${{L}_{b}=l}_{b}\times \left({n}_{e}+{n}_{c}\right)$$\end{document}999.67Total tubing length (mm)\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${L=(L}_{b}+{L}_{v}+{L}_{h} )$$\end{document}5051.07Internal diameter of the tubing\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${D}_{i}$$\end{document}2Cross-sectional area of the tubing (mm2)\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${A}_{c}=\pi {D}_{i}^{2}/4$$\end{document}3.14Total internal volume (mm3)\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${V}_{t}={A}_{c}\times L$$\end{document}15,868.4Total internal volume (ml)\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${V}_{t}$$\end{document}15.87Internal volume of pressure transducer (ml)\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${V}_{trans}$$\end{document}0.2Internal volume of the valve (ml)\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${V}_{val}$$\end{document}0.3Length of the adaptor hole (mm)\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$b$$\end{document}8.5Length of the valve/transducer inside adaptor (mm)\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$a$$\end{document}6Diameter of the adaptor (inner side) (mm)\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${d}_{i}$$\end{document}8.5Volume trapped inside the adaptor (mm3)\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${V}_{adap}=\pi \times {d}_{i}^{2}\times \left(b-a\right)$$\end{document}567.45Volume trapped inside 2 adaptors (ml)\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${V}_{trap}=2\times {V}_{adap}$$\end{document}1.13\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${{\boldsymbol{V}}}_{{\boldsymbol{m}}{\boldsymbol{i}}{\boldsymbol{s}}}={{\boldsymbol{V}}}_{{\boldsymbol{t}}{\boldsymbol{r}}{\boldsymbol{a}}{\boldsymbol{n}}{\boldsymbol{s}}}+{{\boldsymbol{V}}}_{{\boldsymbol{v}}{\boldsymbol{a}}{\boldsymbol{l}}}+{{\boldsymbol{V}}}_{{\boldsymbol{t}}{\boldsymbol{r}}{\boldsymbol{a}}{\boldsymbol{p}}}$$\end{document}Volume to be charged of 30% (ml)\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${V=0.3V}_{t}+{V}_{mis}$$\end{document}6.4Volume to be charged of 50% (ml)\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${V=0.5V}_{t}+{V}_{mis}$$\end{document}9.6Volume to be charged of 70% (ml)\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${V=0.7V}_{t}+{V}_{mis}$$\end{document}12.7 Summary of the geometric details of multiplane (3), multiturn (18) PHP. Heating (evaporator) and cooling (condenser) arrangements Ohmite make (TA1K0PH8R00KE) thin film resistance heater of 8Ω resistance and power rating of 1000 W (maximum) is attached to the base plate of the multiplane PHP. An axial fan of depth 38 mm and rating 130 cfm at 650 Pa is used to create a forced flow of air over the PHP tubes. The fan is fixed into a square duct of area 80 mm × 80 mm and depth 38 mm and discharges air into the enclosure containing the PHP. It may be noted that barring the evaporator portion, which is heated electrically, the rest of the PHP is exposed to air flow and functions as the condenser (there being no adiabatic sections). A helium leak detector (Pfeiffer ASM 182 TD +) is used to find the leak rate in the PHP. The leak rate is of the order 10–6 Torr-L/s. The evaporator is heated by the base plate, which in turn is electrically heated. The thin film resistance heater attached to the base plate is connected to a DC (60 V and 40 A maximum) power supply of APLAB make. The heater power is varied in steps of 50 W beginning from 50 up to 400 W. The voltage is measured at the heater leads with a multimeter of accuracy ± 0.1 V. Due to the electrical heating, the boundary condition at the outer surface of the evaporator can be assumed to be constant heat flux. A combined convective and radiative boundary condition applies to condenser (i.e., the rest of the PHP) because the heat dissipation from the condenser takes place partly to the forced air flow and partly to the surrounding surfaces by radiation. Lower heat inputs, though resulting lower heat flux capability of the PHP, are found to provide a stable pulsating thermal behaviour20. Higher heat inputs are found to produce weaker oscillations. Still higher heat inputs (exceeding 400 W) can cause the dry-out of the fluid inside the evaporator zone. Orientation (Tilt angle) of PHP The orientation of the PHP can be changed from Bottom Heat Mode (BHM) to Top Heat Mode (THM) as shown in Fig. To change the orientation, a rotary disc mechanism is attached to the heat sink. Using the circular scale marked on the rotary disk for the rotation, the PHP can be clamped at any desired angle. The PHP model charged with the required working fluid to the required fill ratio are tested in five different orientations, from the Bottom Heat Mode (BHM) (i.e., vertical position with the evaporator zone situated below the condenser) to the Top Heat Mode (THM, that is the reverse of BHM) by changing the angle in steps of 45°. The orientations are designated as: BHM (+ 90°), + 45°, Horizontal (0°), -45° and THM (-90°). To check the working range for each position, the heat input level is varied from minimum to maximum heat load21. It is of course desirable to have a reliable and efficient heat transfer device unaffected by orientation. At every inclination with respect to gravity, the required data (e.g., the average value of the base plate and tube temperature, at each heat input level) is obtained by covering the range from BHM to THM at all five orientations. The step width for orientation change is 45° for this multiplane PHP. Operating parameters Vacuum of 0.01 Pa was created inside the PHP using a turbo-molecular pump. For this purpose, the PHP is connected to the turbo-molecular pump via the first stop cock, while the second one is closed. The first stop cock is then closed, and the PHP is charged by connecting the second check valve to the loading copper tube. The charging is accomplished by a graduated syringe into which liquid working medium is filled with another syringe with a hypodermic needle22. The port is then opened, and the required amount of liquid is admitted into the PHP tube depending on the fill ratio. The liquid to be taken into the syringe equals the sum of the charge and the dead volumes in the stop cocks and the pressure transducer. Usually, better heat transfer performance requires fill ratios greater than 30%. In the present set of experiments, the fill ratio is chosen to be 30%, 50% and 70%. This multiplane (3), multiturn (18) PHP model is tested with following parametric variable conditions. Fluid: Methanol (Properties are listed in Table2), Fill Ratio: 30%, 50% and 70% in steps of 20%, Operating heat loads (heat fluxes): 50 W, 100 W, 150 W, 200 W, 250 W, 300 W, 350 W and 400 W, Orientations: vertical + 90° (Bottom Heated Mode: BHM), + 45°, horizontal (0°), − 45° and − 90° (Top Heated Mode: THM). Total five tilt angles tested and 1° inclination angle resolution provided in the setup.Table 2The properties at a temperature of 70 °C for the selected fluids23.Fluid (At 70 °C)Molar Mass, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\widetilde{M}$$\end{document} (kg/kmol)Liquid Density, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\rho }_{l}$$\end{document} (kg/m3)\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${(dp/dT)}_{sat}$$\end{document}(kPa/oC)Liquid dynamic viscosity, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\mu }_{l}$$\end{document} (Pa. s)Liquid specific heat, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${c}_{Pl}$$\end{document} (kJ/kg.K)Latent heat of vaporization, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${h}_{fg}$$\end{document} (kJ/kg)Methanol32.04744.394.7523.1126 \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\times {10}^{-4}$$\end{document}2.86821089.1 Table 2The properties at a temperature of 70 °C for the selected fluids23.Fluid (At 70 °C)Molar Mass, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\widetilde{M}$$\end{document} (kg/kmol)Liquid Density, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\rho }_{l}$$\end{document} (kg/m3)\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${(dp/dT)}_{sat}$$\end{document}(kPa/oC)Liquid dynamic viscosity, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\mu }_{l}$$\end{document} (Pa. s)Liquid specific heat, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${c}_{Pl}$$\end{document} (kJ/kg.K)Latent heat of vaporization, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${h}_{fg}$$\end{document} (kJ/kg)Methanol32.04744.394.7523.1126 \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\times {10}^{-4}$$\end{document}2.86821089.1 The properties at a temperature of 70 °C for the selected fluids23. The pressure and temperature data are collected for various orientations and heat fluxes, for different fill ratios and operating fluid is methanol. Temperatures are measured at various points, especially in the condenser and evaporator. Thermal resistance is calculated from the temperature data for all parameters and configurations. An equivalent thermal conductivity is determined based on the fin tip and root temperatures. This parameter indicates the improvement in the heat transfer performance of the PHP compared to that of a dry PHP. Type-J (Iron-constantan) thermocouples (accuracy: ± 1 °C as stated by the manufacturer) are embedded in the respective recesses made in the hardware at various locations, in all four models of PHP. The total number of thermocouples for this model is 19, with one reserved for the ambient temperature measurement. After switching on the condenser fan, the interfaced data logger is turned on. The power supply is switched on and the current is adjusted to achieve the desired heat dissipation. The temperature data is recorded for every 1 s for each channel. The startup and the steady state data are recorded. After each test, the heater is turned off for at least 30 min. The PHP is allowed to reach the ambient temperature before the next parameter set is tested. Temperatures are measured in the evaporator and condenser at the locations shown in Figs. A multiplexer (34980A) of 40 channels is used for temperatures logging and 1 Hz sampling rate is applied for each channel. Using pressure transducer (Honeywell make—PX2AG2XX 002BAAAX), the pressure data is measured and recorded once in every 0.05 s (i.e., pressure sampling frequency = 20 Hz). For 18 turn model, sample tests with methanol at 50% fill ratio and all the heat loads are repeated on three successive days to check the repeatability. The ambient temperature recorded during the course of experimentation for the tested conditions is the range of 26 °C to 28 °C. Initially the condenser fan was switched on, after some time interval the power is supplied to the evaporator to prevent any excessive temperature rise. After this, the interfaced data logger switched to ON position. The electrical power supply is turned to ON position and the desired heat dissipation is maintained by regulating the current supply. The system is started with the lowest heat input of 50 W in this case of model. It is observed that about 5 min time is sufficient for the system to reach a quasi-steady state after the application of heat. Since the system remains at the ambient temperature prior to the application of the 50 W heat input, a time of 15 min is allowed for the system to reach steady state. Later the heat input is increased in steps of 50 W and for each heat input, a time of 10 min is allowed for the PHP to reach steady state. However, the temperature and pressure data are continuously recorded using the DAQ (Data Acquisition System). For changing the fill ratio or working fluid, the PHP is first completely evacuated by drawing the vacuum and is then charged with the required fluid with the required amount to get the desired fill ratio. Performance parameters of PHP The performance of a PHP depends upon several parameters. These are geometrical parameters like tube (or channel) internal diameter, size (i.e., length for a given diameter) of the condenser and the evaporator, and operational parameters like volumetric filling ratio, viscosity of working fluid and thermophysical properties of the working fluid, input heat flux, and orientation of the PHP with respect to gravity24. The oscillatory phenomena might also depend upon inherent disturbances (such as fan flow induced vibration, non-uniformities in temperature of the evaporators, etc.). Increasing the temperature of the heating wall sections significantly increases the total average heat transfer25. Bond number and gravity forces also play an important role in PHP behaviour. Thermal resistance of the heat sink The thermal resistance Rth with respect to the heat load is calculated. Here Rth is calculated as given by the following equation by taking ambient temperature and base temperature for particular heat load.1\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${{\boldsymbol{R}}}_{{\boldsymbol{t}}{\boldsymbol{h}}}=\boldsymbol{ }\frac{{{\boldsymbol{T}}}_{{\boldsymbol{b}}}-{{\boldsymbol{T}}}_{{\boldsymbol{a}}{\boldsymbol{m}}{\boldsymbol{b}}}}{\dot{{\boldsymbol{Q}}}}$$\end{document}for the dry case of without working fluid, the solid conduction resulted in a Rth_dry which was nearly constant across heat loads. This is the highest compared to the PHP \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${R}_{th}$$\end{document}. Equivalent thermal conductivity of the fin Due to the complex geometry of the PHP, particularly the multiplane multiturn geometry, calculation of the convective heat transfer coefficient using the existing correlations is a difficult matter because heat transfer correlations are available for simpler and regular geometries. Hence the convective heat transfer coefficient is determined in the following manner. The input data required to calculate the dry fin heat transfer coefficient are heat load, ambient temperature, base temperature, fin tip temperature, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{cu}(\mathrm{copper})={k}_{f}= 398\text{ W}/\mathrm{m}.\mathrm{K}$$\end{document}, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${D}_{i}$$\end{document}=2 mm and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${D}_{O}$$\end{document} = 3 mm.2\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\dot{{\boldsymbol{Q}}}}_{{\boldsymbol{f}}{\boldsymbol{i}}{\boldsymbol{n}}}={\boldsymbol{M}}\frac{\left(\left.\left({{\boldsymbol{T}}}_{{\boldsymbol{b}}{\boldsymbol{a}}{\boldsymbol{s}}{\boldsymbol{e}}}-{{\boldsymbol{T}}}_{{\boldsymbol{a}}{\boldsymbol{m}}{\boldsymbol{b}}}\right){\boldsymbol{c}}{\boldsymbol{o}}{\boldsymbol{s}}{\boldsymbol{h}}{\boldsymbol{m}}{{\boldsymbol{L}}}_{{\boldsymbol{f}}}-({{\boldsymbol{T}}}_{{\boldsymbol{f}}}-{{\boldsymbol{T}}}_{{\boldsymbol{a}}{\boldsymbol{m}}{\boldsymbol{b}}}\right)\right)}{{\boldsymbol{s}}{\boldsymbol{i}}{\boldsymbol{n}}{\boldsymbol{h}}{\boldsymbol{m}}{{\boldsymbol{L}}}_{{\boldsymbol{f}}}}$$\end{document}where3\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\boldsymbol{m}}=\sqrt{\frac{{{\boldsymbol{h}}}_{{\boldsymbol{f}}}{{\boldsymbol{p}}}_{{\boldsymbol{f}}}}{{{\boldsymbol{k}}}_{{\boldsymbol{f}}}{{\boldsymbol{A}}}_{{\boldsymbol{C}}{\boldsymbol{S}}}}{\boldsymbol{M}}=\sqrt{{{\boldsymbol{h}}}_{{\boldsymbol{f}}}{{\boldsymbol{p}}}_{{\boldsymbol{f}}}{{\boldsymbol{k}}}_{{\boldsymbol{f}}}{{\boldsymbol{A}}}_{{\boldsymbol{c}}{\boldsymbol{s}}}}}$$\end{document} Solving Eq. (2) iteratively for known \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{cu}$$\end{document}, the dry fin heat transfer coefficient is found. The same heat transfer coefficient exists for the tubes of the PHP. Now by using this heat transfer coefficient along with the measured temperatures of the PHP, the equivalent thermal conductivity \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{eq}$$\end{document} is found using Eqs. (2) and (3). The \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{eq}$$\end{document} so calculated should be greater than \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${k}_{cu}$$\end{document} for the device to qualify as a heat pipe. Estimation of heat loss The heat flux applied to the evaporator internal surface is:4\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\dot{{\boldsymbol{q}}}}_{{\boldsymbol{e}}}=({\dot{{\boldsymbol{Q}}}}_{{\boldsymbol{s}}{\boldsymbol{u}}{\boldsymbol{p}}{\boldsymbol{l}}{\boldsymbol{i}}{\boldsymbol{e}}{\boldsymbol{d}}}-{\dot{{\boldsymbol{Q}}}}_{{\boldsymbol{l}}{\boldsymbol{o}}{\boldsymbol{s}}{\boldsymbol{s}}})/{{\boldsymbol{A}}}_{{\boldsymbol{s}}}$$\end{document}where \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${A}_{s}=\pi .{D}_{i}.{L}_{s}$$\end{document}, and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\dot{Q}}_{suplied}$$\end{document} is the electrical power supply to the heater of the base plate and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\dot{Q}}_{loss}$$\end{document} is the heat loss from the surfaces of the base plate by convection and radiation. The heat loss in general is not substantial and is a small fraction of the input power even for the lowest heat load of 50 W. The heater comes with a resin filled epoxy casing whose surface forms the bottom surface of the base plate. Three of the side surfaces are in contact with thick acrylic sheets. Hence the heat loss takes place only through the upper surface and one side surface of dimensions \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$(L\times t)$$\end{document}. A sample calculation for the heat loss from the base plate for \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${T}_{e}=50$$\end{document} °C and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${T}_{amb}=27$$\end{document} °C (i.e., \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${T}_{m}=({T}_{e}+{T}_{amb})/2=38.5$$\end{document}°C) is shown below: The heat loss area (dimensions listed in Table 1) of the block is:5\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\mathbf{A}}_{{\boldsymbol{l}}}={\boldsymbol{L}}{\boldsymbol{t}}+({\boldsymbol{L}}{\boldsymbol{B}}-{\boldsymbol{n}}{\boldsymbol{\pi}}{{\boldsymbol{D}}}^{2}/4)$$\end{document}6\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\text{Prandtl number }\mathbf{P}\mathbf{r}={\boldsymbol{\nu}}/\boldsymbol{\alpha }\text{and Reynolds number}, \mathrm{Re}\boldsymbol{ }={\boldsymbol{V}}{\boldsymbol{D}}/{\boldsymbol{\nu}}$$\end{document} The block surface temperature is \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${T}_{e}$$\end{document}, the ambient temperature of air is \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${T}_{amb}$$\end{document}, the mean temperature \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${T}_{m}$$\end{document} is \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$({T}_{e}+{T}_{amb})/2,$$\end{document} and the characteristic length is B. For this case \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$B=110$$\end{document} mm and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$t=$$\end{document}8 mm. At 38.5 °C, kinematic viscosity of air, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\nu_{{{\mathrm{air}}}} = 1.678 \times 10^{ - 5} {\mathrm{m}}^{{2}} /{\mathrm{s}}$$\end{document}, thermal diffusivity of air, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\alpha_{{{\mathrm{air}}}} = 2.374 \times 10^{ - 5} {\mathrm{m}}^{{2}} /{\mathrm{s}},$$\end{document} and thermal conductivity of air, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$k_{{{\mathrm{air}}}} = { }0.0271{\text{ W}}/{\mathrm{m}} \cdot^\circ {\mathrm{C}}$$\end{document}. The Reynolds number Re = 19,289 for a velocity of 3.5 m/s (laminar regime because Recr = 5 × 105). The combined heat transfer coefficient26 is \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${h}_{o}={h}_{fc}+{h}_{r}$$\end{document}. The forced convective Nusselt number is:7\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\mathbf{N}\mathbf{u}=\boldsymbol{ }\left[0.664\cdot {\mathbf{R}\mathbf{e}}^{(1/2)}{\mathbf{P}\mathbf{r}}^{(1/3)}\right]\boldsymbol{ }=89.046$$\end{document} Convective heat transfer coefficient27,8\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\boldsymbol{h}}_{{{\mathbf{fc}}}} = \left( {{\mathbf{Nu}} \times {\boldsymbol{k}}_{{{\mathbf{air}}}} } \right)/{\boldsymbol{B}} = 23.322 {\mathbf{W}}/{\mathbf{m}}^{2} \cdot^\circ {\mathbf{C}}$$\end{document} The radiative heat transfer coefficient,9\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\boldsymbol{h}}_{{\boldsymbol{r}}} = \left[ {{\boldsymbol{\varepsilon}} \cdot {\boldsymbol{\sigma}} \cdot \left( {{\boldsymbol{T}}_{{\boldsymbol{e}}}^{4} - {\boldsymbol{T}}_{\infty }^{4} } \right)} \right]/\left[ {{\boldsymbol{T}}_{{\boldsymbol{e}}} - {\boldsymbol{T}}_{\infty } } \right] = 0.25435 {\mathbf{W}}/{\mathbf{m}}^{2} \cdot^\circ {\mathbf{C}}$$\end{document} The emissivity (for lightly oxidized copper) is taken as 0.037. The average temperature of the surrounding surfaces is taken to be the same as the ambient air temperature \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${T}_{\infty }$$\end{document}. The quantity \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\sigma$$\end{document} is the Stefan-Boltzmann constant = 5.67037 \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\times {10}^{-8}$$\end{document} W/m2.K4. Heat loss28,10\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\dot{{\boldsymbol{Q}}}}_{{\boldsymbol{l}}{\boldsymbol{o}}{\boldsymbol{s}}{\boldsymbol{s}}}={{\boldsymbol{A}}}_{{\boldsymbol{l}}}\cdot {{\boldsymbol{h}}}_{{\boldsymbol{O}}}\cdot ({{\boldsymbol{T}}}_{{\boldsymbol{e}}}-{{\boldsymbol{T}}}_{{\boldsymbol{a}}{\boldsymbol{m}}{\boldsymbol{b}}})= 6.53\text{ W},\text{ for }50\text{ W input}$$\end{document} In this manner the heat loss is computed for all the heat loads and the heat loss is correlated as a function of the electrical heat input. The heat loss correlation is:11\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\dot{Q}}_{loss}=2\times {10}^{-6} {\dot{Q}}_{s}^{2}+0.267 {\dot{Q}}_{s}-7.2072,$$\end{document}where both the quantities are in W. Results and discussion The upper and lower sets of curves correspond to evaporator and condenser, ambient temperature also indicated. It can be seen that for all parametric variable conditions, the evaporator base plate undergoes insignificant oscillations. Dry test three-plane, 18-turn PHP The multiplane PHP is first tested in dry configuration, i.e., without working fluid. The heat is supplied to the setup in steps 50 W in the range 50 W to 200 W and the test is stopped for base plate temperatures exceeding 110 °C. Conduction heat transfer takes place through the cross-sectional area of the tube alone and the setup behaves like a normal pin fin heat sink with forced convection and radiation. Therefore, in the dry test fluid-induced oscillations cannot be present. The steady state temperatures of the base plate are 43.8 °C for 50 W, 62.9 °C for 100 W, 78.2 °C for 150 W and 95.3 °C for 200 W, as shown in Fig. 5 As mentioned, the locations at which temperatures are monitored with thermocouples are shown in Fig. 2. In Fig. 5 the topmost curve is for the base plate. The middle set of curves is for the evaporator part, the locations being very nearer to the base plate on one side or both the sides of the U-bend. The lowermost set of curves is for locations on one side or both the sides of the upper U-bends. The lowest curve in the lowermost set of curves is for the ambient temperature. An appreciable rise in temperature is observed for each heat load. For 150 W and 200 W, a slight rise in the condenser temperature is observed. The device attains a constant thermal resistance (Rth,dry) when the steady state is reached.Fig. 5Dry test three-plane, 18-turn PHP. Dry test three-plane, 18-turn PHP. Fill ratio (30%) for methanol fluid, three-plane, 18-turn PHP Results for 30% fill ratio for all heat loads and orientations are as shown in Fig. 6 for methanol. Oscillatory behaviour begins for + 90° (BHM) at 100 W, + 45° at 100 W, horizontal (0°) at 100 W, − 45° at 150W − 90° at 200 W. When the heat load is changed, after the initial transients during which there is a temperature rise, a pseudo steady state is established until dry-out of the working fluid particularly at higher heat loads. The device really functions as a PHP due to the vigorous oscillations from BHM to − 90° orientations. All orientations shows strong oscillations.Fig. 6Temperature distribution in multi-plane three-plane, 18-turn PHP for different orientation and 30% fill ratio of methanol. Temperature distribution in multi-plane three-plane, 18-turn PHP for different orientation and 30% fill ratio of methanol. Thermal horns are also observed at the beginning of the oscillations in the base plate, for BHM to − 90° orientations. The negative angle orientation − 45° and − 90° took more time for start-up until that heat is transported largely by wall conduction and from the evaporator it dissipated to the flowing air. Fill ratio (50%) for methanol fluid, three-plane, 18-turn PHP Results for 50% fill ratio for all heat loads and orientations are as shown in Fig. 7 The salient points are as follows. Onset of oscillatory behaviour: + 90° (BHM) at 100 W, + 45° at 50 W, horizontal (0°) at 100 W, − 45° at 100 W, − 90° at 150 W. Vigorous oscillations: From BHM to -90° orientations. Functioning like a fin: − 90° orientation.Fig. 7Temperature distribution in three-plane, 18-turn PHP for different orientation and 50% fill ratio of methanol. Temperature distribution in three-plane, 18-turn PHP for different orientation and 50% fill ratio of methanol. Fill ratio (70%) for methanol fluid, three-plane, 18-turn PHP Results for 70% fill ratio for all heat loads and orientations are as shown in Fig. 8 The salient points are as follows. Onset of oscillatory behaviour: + 90° (BHM) at 150 W, + 45° at 100 W, horizontal (0°) at 150 W, − 45° at 150 W, − 90° at 200 W. Vigorous oscillations: From BHM to − 90° orientations (− 45° and − 90° (THM) vigorous and very high peak oscillations compared to any other condition and geometry). Functioning like a fin: − 45° and − 90° (THM) orientation.Fig. 8Temperature distribution in three-plane, 18-turn PHP for different orientation and 70% fill ratio of methanol. Temperature distribution in three-plane, 18-turn PHP for different orientation and 70% fill ratio of methanol. Comparison of results for three-plane, 18-turn PHP For various conditions of multiplane (3) multiturn (18) PHPs, the equivalent thermal resistance curves are plotted (as shown in Fig. 9). + 45O (50%) for methanol thermal resistance is lowest.Fig. 9Combined thermal resistance for methanol fluid, fill ratio and orientation for three-plane, 18-turn PHP. Combined thermal resistance for methanol fluid, fill ratio and orientation for three-plane, 18-turn PHP. For various conditions of multiplane (3) multiturn (18) PHPs, flow field observations for different fluids are listed in Table 3 In 50 W for methanol the movement of the fluid inside the PHP is absent.Table 3Three-plane, 18-turn PHP for methanol fluid.50 W100 W150 W200 W250 W300 W350 W400 WBHM30%–SOOCCCC50%–SOOCCCC70%––SOOCCDHorizontal30%–SOOCCCC50%–SOOCCCC70%–SOOCCCCTHM30%–––SOCCC50%––SOOCCC70%–––SOOCCS: Partial Start up, O: Oscillation, C: Circulation, D: Dry-out, remaining (–) positions the movement of the fluid inside the PHP is absent. Table 3Three-plane, 18-turn PHP for methanol fluid.50 W100 W150 W200 W250 W300 W350 W400 WBHM30%–SOOCCCC50%–SOOCCCC70%––SOOCCDHorizontal30%–SOOCCCC50%–SOOCCCC70%–SOOCCCCTHM30%–––SOCCC50%––SOOCCC70%–––SOOCCS: Partial Start up, O: Oscillation, C: Circulation, D: Dry-out, remaining (–) positions the movement of the fluid inside the PHP is absent. Three-plane, 18-turn PHP for methanol fluid. S: Partial Start up, O: Oscillation, C: Circulation, D: Dry-out, remaining (–) positions the movement of the fluid inside the PHP is absent. Conclusions Experimental investigations are carried out on PHP with multi-plane geometrical configurations. For this model the tube inner diameter is 2 mm. The condenser (or fin portion) of the PHP is cooled by forced air flow and radiation to the surrounding surfaces. Parametric runs are conducted by varying fill ratio, orientations, and heat loads. The working fluids namely methanol is employed. PHP with 18 turns are tested for fill ratios of 30%, 50% and 70% and five orientations, namely + 90°, + 45°, 0° (horizontal), − 45° and − 90° with respect to the horizontal. Heat loads are increased in steps of 50 W from 50 to 400 W for testing the PHP. The major conclusions from the work are as follows:As per Bond criteria, the tube diameter is fixed at 2 mm for methanol. The performance of the multi-plane PHP model is good in both positive and negative angle orientations.Start-up characteristics vary for different heat loads. Sudden start-up at lower heat loads and gradual and smooth start-up for higher heat loads is observed. This variation could be due to differences in void fraction distribution.The succession of events in the evaporator temperature in most of the runs is: (i) a gradual rise, (ii) a temperature overshoot (or horn), (iii) onset of oscillatory behaviour, and (iv) a kind of pseudo steady state. In some of the runs dry-out of the fluid is observed at the end of the heating period. Start-up temperature is lower in BHM, and it increases towards THM. The equivalent thermal conductivity also changes from BHM to THM.Good heat transfer performance is observed between 50° and 70° orientations. The PHP fluid motion is associated with vigorous oscillations in BHM and the oscillations decrease as THM is reached.The average thermal resistances \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${R}_{th}\left(^\circ{\rm C} /W\right)$$\end{document} for 18 multiplane is 0.3408 compare to dry fin thermal resistance \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${R}_{dry}$$\end{document} \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left(0.45^\circ{\rm C} /W\right)$$\end{document}. As per Bond criteria, the tube diameter is fixed at 2 mm for methanol. The performance of the multi-plane PHP model is good in both positive and negative angle orientations. As per Bond criteria, the tube diameter is fixed at 2 mm for methanol. The performance of the multi-plane PHP model is good in both positive and negative angle orientations. Start-up characteristics vary for different heat loads. Sudden start-up at lower heat loads and gradual and smooth start-up for higher heat loads is observed. This variation could be due to differences in void fraction distribution. Start-up characteristics vary for different heat loads. Sudden start-up at lower heat loads and gradual and smooth start-up for higher heat loads is observed. This variation could be due to differences in void fraction distribution. The succession of events in the evaporator temperature in most of the runs is: (i) a gradual rise, (ii) a temperature overshoot (or horn), (iii) onset of oscillatory behaviour, and (iv) a kind of pseudo steady state. In some of the runs dry-out of the fluid is observed at the end of the heating period. Start-up temperature is lower in BHM, and it increases towards THM. The equivalent thermal conductivity also changes from BHM to THM. The succession of events in the evaporator temperature in most of the runs is: (i) a gradual rise, (ii) a temperature overshoot (or horn), (iii) onset of oscillatory behaviour, and (iv) a kind of pseudo steady state. In some of the runs dry-out of the fluid is observed at the end of the heating period. Start-up temperature is lower in BHM, and it increases towards THM. The equivalent thermal conductivity also changes from BHM to THM. Good heat transfer performance is observed between 50° and 70° orientations. The PHP fluid motion is associated with vigorous oscillations in BHM and the oscillations decrease as THM is reached. Good heat transfer performance is observed between 50° and 70° orientations. The PHP fluid motion is associated with vigorous oscillations in BHM and the oscillations decrease as THM is reached. The average thermal resistances \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${R}_{th}\left(^\circ{\rm C} /W\right)$$\end{document} for 18 multiplane is 0.3408 compare to dry fin thermal resistance \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${R}_{dry}$$\end{document} \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left(0.45^\circ{\rm C} /W\right)$$\end{document}. The average thermal resistances \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${R}_{th}\left(^\circ{\rm C} /W\right)$$\end{document} for 18 multiplane is 0.3408 compare to dry fin thermal resistance \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${R}_{dry}$$\end{document} \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\left(0.45^\circ{\rm C} /W\right)$$\end{document}.