Laser-Assisted Diamond Cutting for Low-Damage Fabrication of High-Q CaF2 Whispering-Gallery Mode Resonators Authors: Rongbiao Yang, Tao Jia, Jiamin Rong, Huanfei Wen, Zhidong Xu, Zihan Song, Enbo Xing, Jun Tang, Jun Liu Published: 2026 ABSTRACT Calcium fluoride (CaF2) crystals are an ideal material for fabricating high-quality whispering-gallery-mode (WGM) optical resonators. However, their hard and brittle nature make it difficult to achieve low-damage, ultra-smooth surfaces through conventional cutting, which limits the optical performance of the resonators. To address this, laser-assisted diamond cutting technology is proposed in this study for low-damage and high-quality fabrication. Molecular dynamics simulations reveal the atomic-scale mechanism by which laser thermal effects reduce cutting forces and promote dislocation motion. Nano-scratch experiments further show that the critical depth of ductile–brittle transition (DBT) increases from 388 nm to 1070 nm, 2.76 times that of conventional cutting. Based on these results, ultra-precision turning of a high-quality hemispherical resonator with a Q factor of up to 1.3 × 108 was achieved. This study provides an effective solution for low-damage and high-performance resonator fabrication from hard and brittle optical crystals. 1. Introduction Calcium fluoride (CaF2) crystals [1,2], with their broad transparent wavelength range, stable refractive index, and excellent thermo-optical properties, have become a key material for high-end optical systems such as deep-ultraviolet lithography and high-power lasers. Particularly promising are CaF2 whispering-gallery mode (WGM) resonators [3,4,5] with ultra-high Q, which have shown great potential in integrated photonics, quantum information processing, and ultra-sensitive sensing [6]. These resonators operate via total internal reflection, confining optical fields within microscale volumes over extended periods, thereby significantly enhancing light–matter interaction [7,8]. Theoretically, millimeter-scale CaF2 WGM resonators can achieve measurement precision equivalent to kilometers of optical fiber, positioning them as an ideal platform for next-generation all-solid-state quantum sensors. Previous studies have demonstrated that ultra-high Q factors (>109) can be achieved through ultra-precision polishing techniques [9,10]. However, these approaches are typically time-consuming and lack fabrication efficiency. Single-point diamond turning combined with subsequent polishing can provide a balance between form accuracy and optical performance, but it often introduces surface and subsurface damage. Such processing-induced defects not only increase scattering loss and limit the Q factor, but also distort the intracavity field distribution and degrade mode dispersion [11,12]. Moreover, they hinder stable low-noise coupling and integration. Therefore, developing a novel manufacturing technology that offers high precision, high efficiency, and low damage has become essential to overcome the performance bottlenecks of ultra-high-Q CaF2 WGM resonators. Recent advances in laser-assisted machining have demonstrated significant potential for processing hard and brittle materials, such as silicon [13], germanium [14], sapphire [15], and silicon carbide [16]. The underlying mechanism is primarily attributed to laser-induced thermal softening, which reduces cutting forces, suppresses brittle fracture, and extends the ductile machining regime [17]. For CaF2 crystals, several studies have investigated their deformation and material removal behavior; for example, Lee et al. [18] examined the influence of crack morphology on ductile-mode cutting performance, while Guo et al. [19] investigated the magnetoplastic scratching mechanism and the anisotropic ductile–brittle transition behavior of CaF2 single crystals during micro-cutting. Although substantial progress has been achieved in laser-assisted machining of various brittle materials, its application to fluoride crystals remains limited, particularly in the fabrication of WGM resonators, where ultra-smooth surfaces and minimal subsurface damage are critically required. In this paper, we established the theoretical and experimental foundation for low-damage, high-precision machining of CaF2 crystal WGM resonators. By integrating a laser heat source with precision mechanical cutting, the localized mechanical properties of the material were modulated via thermal effects, enabling material removal dominated by the plastic regime and thereby fundamentally suppressing surface damage. A laser-assisted diamond cutting system was constructed and employed to fabricate a WGM optical resonator with a quality factor of 1.3 × 108. Therefore, this technology is expected to provide a practical and feasible solution to the manufacturing challenges of fluoride WGM optical microcavities and further promote their applications in integrated photonics and high-sensitivity sensing. 2. Molecular Dynamics Simulation In the MD simulation [20,21,22] of laser-assisted nano-cutting [23], the computational model consists of a diamond tool and a CaF2 crystal workpiece, as illustrated in Figure 1. For the single-point diamond turning (SPDT) machining [24,25,26] of brittle materials, employing an appropriate negative rake angle [27] helps reduce cutting force fluctuations, thereby facilitating higher machining surface quality within the plastic deformation regime. Accordingly, this model sets the geometric parameters of the diamond tool as follows: rake angle of −20°, clearance angle of 10°, and edge radius of 1 nm [28]. The tool consists of 28,117 carbon atoms and is treated as a rigid body in the simulation to eliminate interference from tool wear on the results [17,29,30]. Due to the time constraints imposed by available computational resources, reduced model dimensions and higher-than-realistic cutting velocities are typically employed, which are common characteristics of the MD approach. To mitigate potential scale effects, all geometric parameters of both the workpiece and the diamond tool were scaled proportionally using a consistent scaling factor. The workpiece is a cubic crystal system CaF2 crystal, whose unit cell structure is shown in Figure 1. The simulated model of the workpiece comprises a total of 177,408 atoms, with dimensions of 22.064 nm (length) × 11.032 nm (thickness) × 11.032 nm (width). Along the thickness direction, the workpiece is partitioned into three zones [31]: the boundary layer, the thermostatic layer, and the Newtonian layer. The thicknesses of both the boundary and thermostatic layers are set to 5 Å. The interactions between ions in the CaF2 crystal are described using the Buckingham potential combined with long-range Coulomb interactions. The potential function is expressed as follows [19]: (1)EB=Ae−r/ρ−Cr6,r