Multifunctional scaffold based on Ti3C2Tx/PCL nanofibers composite hydrogel directs myogenic differentiation and microenvironment remodeling for volumetric muscle loss Authors: Yihui Zhang, Wenkai Zhang, Zeyuan Xie, Wei Yu, Xiangqi Zhang, Yangwen Luo, Muge Gu, Jiayu Wang, Wei-En Yuan, Yebin Qian Published: 2026 ABSTRACT Volumetric muscle loss (VML) regeneration remains clinically challenging, primarily due to compromised myogenic differentiation and an oxidative-inflammatory microenvironment that impedes regeneration. Consequently, timely resolution of inflammation and dynamic remodeling of the immune niche are imperative for functional VML recovery. Ti3C2Tx MXene, a two-dimensional nanomaterial, demonstrates significant potential in biomedical applications owing to its anti-inflammatory and immunomodulatory properties. However, oxidative degradation and hydrolysis occur upon aqueous exposure, leading to compromised bioactivity. To preserve structural integrity and mitigate oxidative degradation of Ti3C2Tx MXene, it was encapsulated in electrospun fibers to fabricate Ti3C2Tx MXene/PCL membrane (MP). This biomimetic multifunctional scaffold was fabricated via hydrogen bond-driven self-assembly, integrating alternating layers of MP membranes and hyaluronic acid-catechol/4-arm-PEG (HP) hydrogel, and is hereinafter referred to as the MPHP scaffold. In vitro analyses demonstrated enhanced cellular adhesion and myogenic differentiation (evidenced by > 3.9-fold upregulation of myogenic differentiation (MyoD) and >2.9-fold upregulation of myogenin (MyoG)), confirming potent myogenesis-promoting capabilities. In vitro and in vivo analyses consistently demonstrated the scaffold's capacity to reprogram macrophage polarization to regenerative M2 phenotypes, effectively remodeling the regenerative niche. During the remodeling phase, it accelerated myotube fusion and maturation, while concurrently promoting angiogenesis and neuromuscular junction reinnervation. These coordinated mechanisms restored structural and functional muscle integrity, with treated VML models exhibiting a 38% increase in exercise tolerance versus controls. The MPHP scaffold thus represents a multifunctional biomimetic platform for VML regeneration, demonstrating significant translational potential in tissue engineering. Moreover, this encapsulation strategy preserves Ti3C2Tx MXene bioactivity and expands its therapeutic applicability beyond conventional limitations. Introduction The musculoskeletal system is essential for movement, support and protection of the human body and accounts for approximately 40% of the total body weight [1,2]. Volumetric muscle loses (VML) refers to traumatic or surgical loss of skeletal muscle with 20% or more of the muscle belly by weight. It's a devastating injury that challenges muscle repair capacity, resulting in severe permanent muscle damage, structural changes, and impaired limb function [3]. Currently, autologous and allogeneic transplantation in clinical practice have the risk of infection, necrosis and the serious risk of immune rejection [4,5]. In addition, some gene and cell therapies are still in clinical trials, but their therapeutic methods and effects still need to be further explored [[6], [7], [8]]. At present, clinical attention has turned to tissue engineering and regenerative medicine, hoping to create multifunctional muscle scaffold capable of mimicking the natural muscles to rebuild its structure and function [9]. Skeletal muscle repair and regeneration is a complex process consisting of several consecutive and overlapping stages, involving the participation of multiple cells, growth factors and cytokines [10]. The muscle regeneration first contains a proinflammatory phase, which is associated with increased inflammatory responses and activation of muscle stem cells (MuSC), followed by a recovery phase, which is characterized by the transmission of anti-inflammatory cues that maintain myofiber formation, angiogenesis, matrix remodeling, and ultimately lead to functional recovery of the muscle [[11], [12], [13]]. Notably, macrophages constitute the largest collection of immune cells during muscle regeneration, from initial injury to late remodeling of muscle tissue. During muscle regeneration, they exert various functions on multiple cells while adjusting their phenotype and function throughout regeneration [14]. After muscle injury, macrophages rapidly accumulate and secrete nitric oxide, which promotes the degradation of muscle fibers and induces vasodilation to recruit more inflammatory cells. Pro-inflammatory M1 macrophages engraft necrotic muscle fibers and support the growth and proliferation of satellite cells and inhibit premature myogenic cell fusion [[15], [16], [17]]. Anti-inflammatory M2 macrophages promote the differentiation of myoblasts (myoblasts differentiate into myogenin expressing myocytes) and fusion into multinucleated myotubes [18,19], thereby accelerating the regeneration process. While persistent M1 macrophages, in addition to stimulating macrophage phagocytosis, also inhibit the recruitment or phenotypic differentiation of M2 macrophages [20]. In addition, Latroche et al. found that anti-inflammatory macrophages were able to stimulate the co-formation of capillaries and myotubes in 3D triple cultures in vitro [21]. Two-dimensional Ti3C2Tx MXene has attracted more and more attention in the field of biomedicine due to its unique properties such as high conductivity, layered structure, adjustable surface chemistry, and excellent mechanical properties [22,23]. The structure of Ti3C2Tx exhibits an alternate arrangement of Ti and C layers, and the surface is covered by various functional groups (-OH, -O, -F, etc.) after peeling-off from the MAX phase [24,25]. Some studies have found that the incorporation of Ti3C2Tx MXene into hydrogels confers conductivity and antioxidant properties, which can be applied in the field of tissue regeneration. Wei et al. [26] found that crosslinking MXenes into hydrogels to prepare conductive hydrogels can provide an extracellular matrix-like substrate for the growth of NSCs, which can effectively promote the proliferation and differentiation of NSCs. Zheng et al. [27] prepared hydrogels incorporating Ti3C2Tx MXene@MnO2 nanoparticles and found that they promoted muscle regeneration through electroactivity and microenvironment management. But directly adding Ti3C2Tx MXene to the hydrogel means that the nanosheets will be in constant contact with water. It has been shown that MXene degrades more easily in aqueous solution than in other states, and except to the oxidative degradation caused by oxygen and dissolved oxygen, it also undergoes direct hydrolysis, which results in impaired structure and function [[28], [29], [30]]. As a result, the service life of Ti3C2Tx MXene is reduced, thus limiting its application. It is therefore crucial to find effective strategies to avoid oxidation and preserve its structure and properties. While various drugs have been explored to mitigate fibrosis or promote myogenesis, pharmacological interventions alone cannot regenerate lost muscle mass or restore contractile function after VML injury. For instance, formoterol treatment increased peak isometric torque by 18% over untreated VML controls, and adding leucine reduced losses in muscle mass, whole-body lipid oxidation, and strength. However, formoterol's efficacy is limited: muscle mass and function remained far below healthy levels, and its benefits depended on concurrent rehabilitation. In contrast, losartan, though effective at reducing fibrosis, paradoxically impaired muscle function. Together, these findings show that single-agent pharmacotherapy cannot compensate for the physical loss of muscle tissue. An ideal VML repair strategy thus requires a combination of tissue engineering scaffolds, cell-based therapies, and/or rehabilitative training. Muscle regeneration is a long-term and complex process. Therefore, there is a need for a method that can exert the efficacy of Ti3C2Tx MXene while reducing its oxidative or hydration inactivation in the process. Despite its favorable properties, PCL has several intrinsic limitations that restrict its application in VML repair. the slow degradation kinetics of poly-ε-caprolactone (PCL)(typically 2–3 years for complete absorption) do not align with the faster timeline required for functional muscle regeneration, potentially hindering timely tissue remodeling. Besides, PCL is bioinert and lacks the bioactive cues necessary to actively promote myogenesis, angiogenesis, or immunomodulation, often requiring functionalization with bioactive molecules or nanomaterials to enhance its regenerative capacity. Therefore, we mixed Ti3C2Tx MXene nanosheets into the spinning fibers to prepare Ti3C2Tx MXene/PCL (MP). With the degradation of the scaffold, Ti3C2Tx MXene is gradually exposed to play a role in different stages of regeneration. The intrinsic biomimetics of nanofibers, including high surface area to volume ratio, porous structure and excellent mechanical properties that closely resemble the complex structure of natural ECM, are expected to coordinate cellular behaviors critical in muscle repair and regeneration [31,32]. However, the direct use of spinning membrane for VML still has problems such as poor hydrophilicity and poor tissue adhesion, which will affect its therapeutic effect. Hyaluronic acid (HA) is a major component of the skeletal muscle extracellular matrix and plays a critical role in muscle development and regeneration. HA-based hydrogels have been extensively explored for tissue engineering due to their excellent biocompatibility, tunable mechanical properties, and ability to support cell adhesion and proliferation. Recently, catechol-conjugated HA (HA-CA) hydrogels have emerged as a promising platform for muscle repair. In a 2025 study by Lee et al., an HA-CA patch incorporating muscle tissue-derived extracellular matrix (MEM) effectively stimulated satellite cell activation and supported de novo muscle regeneration with functional restoration in a rat VML model [33]. Moreover, the adhesive properties of HA-CA hydrogels, conferred by the catechol moieties, enable seamless integration with host tissue and sustained retention at the injury site, which is particularly advantageous for VML repair where mechanical stability is critical. Therefore, it would be an efficient strategy to integrate MP membrane into such a composite scaffold by layer-by-layer stacking of membrane with hydrogel, which can mimic natural skeletal muscle tissue characteristics and promote cell adhesion and growth. Herein, MP nanofiber membranes were prepared by electrospinning. Subsequently, this membrane was layered with a hydrogel comprising HA-CA crosslinked with 4-arm PEG-SH (forming HP hydrogel), resulting in a multifunctional biomimetic scaffold. By enhancing the stability of Ti3C2Tx MXene, the MPHP scaffold preserved its ability to effectively scavenge free radicals, protect cells from oxidative stress damage, and retain functionality across different stages of muscle regeneration. The scaffold is anticipated to promote volumetric muscle loss (VML) regeneration and restore muscle structure and function by modulating the regenerative immune microenvironment and guiding myogenic differentiation and myogenesis. Materials and methods Materials HA (MW:40-80 kDa), 1-(3-Dimethylaminopropyl)-3-ethylcarbodiimide hydrochloride (EDC), N-Hydroxy succinimide (NHS), were obtained from Shanghai Macklin Biochemical Co., Ltd (CHN). 4-arm PEG-SH (MW:2 kDa) was purchased from Shanghai Yuanyang Bio Tech. Inc. (CHN). Dopamine hydrochloride (DA∙HCl) was purchased from Sigma-Aldrich (St. Louis, MO, USA). PCL (Capa 6400) was obtained from Perstorp (SWE). Ti3C2Tx MXene nanosheets were obtained from Xi 'an Qiyue Biotechnology Co., LTD (CHN). Hexafluoroisopropanol (HFIP, 99.5 %) was procured from Beijing InnoChem Science & Technology Co., Ltd. 1,1-Diphenyl-2-picrylhydrazyl (DPPH) was obtained from Yuanye Bio-Technology Co. Ltd. (CHN). DCFH-DA assay kit, lipopolysaccharides (LPS) and IL-4, lactate dehydrogenase (LDH) release assay kit and CCK-8 assay kit were purchased from Shanghai Beyotime Biological Co., Ltd. (CHN). Riboflavin, methionine, nitrotetrazolium chloride, salicylic acid, FeSO4, ABTS and potassium persulfate were obtained from Shanghai Adamas Reagent Co., Ltd (CHN). H2O2 was purchased from Sinopharm Chemical Reagent Co., Ltd (CHN). FBS (FSD500) was obtained from ExCell Biotech Co., Ltd. (CHN). Penicillin-streptomycin and basic medium was purchased from Grand Island Biological Company (Gibco, USA). RAW 264.7 cells and C2C12 cells were ordered from the cell bank of Chinese Academy of Sciences (Shanghai, CHN). Isoflurane was obtained from Shenzhen ruiwode Life Technology Co., Ltd (CHN). 4% paraformaldehyde obtained from Wuhan Servicebio Technology Co., Ltd (CHN). All the antibodies were purchased from Abcam (CHN). Characterization of Ti3C2Tx MXene nanosheets The microstructure properties of Ti3C2Tx MXene nanosheets were characterized by transmission electron microscopy (TEM) (FEI Talos, F200X S/TEM, ThermoFisher Scientific Co.). X-ray photoelectron spectroscopy (XPS) (AXIS Ultra DLD, Shimadzu) was performed to measure Ti3C2Tx. Preparation and characterization of electrospinning nanofiber membrane The 15% w/w PCL solution was obtained by dissolving PCL in HFIP. Ti3C2Tx MXene nanosheets with different contents (Ti3C2Tx: PCL = 0.5%, 1% and 2%; w/w) were dissolved in deionized water and sonicated in an ice bath for 5 min. The two solutions were mixed and stirred in a magnetic stirrer for 0.5 h. The PCL and MP nanofiber membranes were produced using an electrospinning device (SS-2534, Ucalery Technology and Development, Beijing, CHN). The electrospinning experimental conditions were as follows: voltage (−4 kV, +10 kV), flow rate (0.2 mm min−1), needle (18 G), collector distance (15 cm), collector rotation speed (600 rpm) and room temperature. The ambient relative humidity inside the electrospinning device was controlled within the range of 25% to 40%. The prepared nanofiber membranes were vacuum dried in a desiccator for 24 h to remove residual HFIP. Characterization of the mechanical properties of the membrane The mechanical properties of nanofiber membranes were evaluated by using a dynamic mechanical analysis (Q850, TA, USA). The DMA analysis of the membranes was performed with reference to the specifications of ISO 6721-9:2019 (R2024) in tensile mode. Specifically, the membranes were cut into rectangles (70 mm × 15 mm, length × width), and the thickness was recorded through a micrometer. The ends of the membrane were clamped and pulled at a rate of 10 mm/min until breaking, and their stress-strain curves were recorded. Construction of PHP and MPHP scaffolds HA-CA was prepared according to the method of zhong et al. [34,35]. The chemical structure of HA-CA conjugate was confirmed using FTIR spectroscopy (Nicolet 6700, Thermo scientific, USA) and 1H NMR (400 MHz, Bruker AMX-400, USA). HP hydrogel was prepared by dissolving HA-CA in PBS (pH = 5.8) and mixing with 250 mg/mL 4-arm PEG-SH (8:1, v/v). The hydrogel was then formed by adjusting pH to 7.5 with 1 M NaOH. The microstructures of the HP hydrogel were observed by scanning electron microscopy (SEM) (VEGA/IAC, SJTU), and energy dispersive spectrometer (EDS) mapping analysis was performed to determine the distribution of Ti atoms. Water contact angles of PCL and MP membranes were measured using a video-optical contact angle meter (DSA100, KRÜSS Scientific). PCL and MP nanofiber membranes were cut into rectangles (10 mm × 5 mm, length × width). The prepared HP hydrogel was coated onto a custom-fabricated mold, followed by deposition of the nanofiber membrane. The multilayered scaffold was subsequently assembled by sequentially stacking three hydrogel layers alternated with two nanofiber membranes. Swelling behavior of HP hydrogels To investigate the structural stability of the scaffolds, 1% and 2% HP hydrogels were prepared. Initial weights (W0) of hydrogels were recorded, after which they were immersed in phosphate buffered saline (PBS, 5 mL) at 37 °C. They were removed and weighed (Wt) at predetermined time. The test was repeated three times. The equilibrium swelling ratio was calculated as the following formula:Swellingratio(%)=Wt−W0W0×100% Rheological measurements A rotational rheometer (DHR20, TA, USA) was using to determine the rheological characteristics of hydrogels. The characterization of the mechanical properties of the hydrogel was performed in accordance with the guidelines of ASTM F2900, whereas the specific testing protocol was based on ISO 6721-10 with appropriate optimizations. The hydrogels were placed between parallel plates (plate diameter: 20 mm; gap: 500 μm). Oscillatory frequency sweeps were conducted from 0.1 to 100 rad/s at a constant strain of 1% (within the linear viscoelastic region) and a temperature of 25 °C. The storage modulus (G’) were recorded under a frequency sweep mode. In vitro release of Ti3C2Tx The prepared 1% MP electrospun membrane was immersed in a vial containing 1 mL of PBS (pH 7.4) and placed in a thermostatic shaker (100 rpm, 37 °C). At predetermined time points (1, 4, 7, 14, 30 and 60 days), 200 μL of the release medium was withdrawn and an equal volume of fresh, pre-warmed release medium was replenished. The withdrawn samples were diluted with 2% nitric acid, and the amount of released Ti was quantified using inductively coupled plasma optical emission spectrometry (ICP-MS, i CAP Q, Thermo, USA). The test was repeated three times. In vitro degration of MPHP scaffold The prepared MPHP scaffold was implanted subcutaneously into rats - a simple procedure that facilitates observation, sample retrieval, and preliminary assessment of degradation. Briefly, after removing the dorsal hair and disinfecting the skin with iodophor, a small incision was made. The sterilized scaffold was inserted subcutaneously, placed flat, and the incision was closed with sutures. The wound was then disinfected again with iodophor to prevent infection. Cell viability and proliferation assays Lactate dehydrogenase (LDH) release assays and CCK-8 assays were used to detect the cytotoxicity and proliferation of C2C12 cells exposed to PHP and MPHP scaffolds, respectively. The concentration of C2C12 cell suspension was diluted to 2 × 104 ml−1, and cultured with PHP and MPHP scaffolds. After 24 h of culture with the scaffolds, the test was performed according to the instructions of LDH test kit. Absorbance was read on a microplate reader at a detection/reference wavelength of 490/630 nm (Synergy LX, BioTek, USA). CCK8 was used to evaluate the effect of the scaffolds on cell proliferation after 1, 3 and 5 days of culture. Absorbance was read on a microplate reader at a detection/reference wavelength of 450/630 nm. Extraction of primary muscle cell Primary muscle cells were extracted using the tissue mass cell culture method. Newborn BALB/c mice (0-1 days after birth) were euthanised via cervical dislocation, and limb muscles were cut into 1 mm3 size with ophthalmic scissors after removal of fat, connective tissue, and bone. The muscle patches were soaked with medium and evenly coated on the wall of the culture bottle, with the spacing between each patch being 0.2 cm - 0.5 cm. The bottle was placed bottom up, medium was added to the bottle and placed in a 37 °C cell incubator. After incubation for 2 to 4 h, the small pieces of muscle were attached to the wall, and the bottle was slowly flipped and laid flat. Primary muscle cells were cultured in DMEM/F-12 medium containing 20% FBS. After 3-5 days of incubation, the medium was replaced with fresh medium. Live/dead staining Membranes were cut with a circular cutter to fit in 24-well cell culture plates and immersed in 75% ethanol for 30 min. The sterilized membranes were placed in 24-well plates containing cell slides and secured with sterile steel rings. Subsequently, C2C12 and muscle primary cells were seeded on membranes at a concentration of 105, respectively. After 24 h of culture, the cells were stained with the live/dead staining kit (Beyotime) according to the manufacturer's instructions. The fluorescence images were taken by high resolution laser confocal microscopy (Leica STELLARIS 5, Leica, GER) and inverted fluorescence microscope (IX73, Olympus, JPN). Free radical scavenging assay •OH and O2•- scavenging assays were used to assess the ROS scavenging ability of the MPHP scaffolds. The scavenging ability of ·OH was determined by Fenton reaction. The sample was placed in the test solution of 10 mM FeSO4 and 10 mM H2O2. After incubation for 10 min, 10 mM salicylic acid-ethanol was added and incubated in the dark for 30 min [36]. The absorbance of the solution at 510 nm was recorded using a plate reader (infinite M200 Pro, TECAN) and the ·OH scavenging was calculated. For O2•- scavenging assays, assay solutions were prepared in PBS containing riboflavin (20 μM), methionine (12.5 mM), and nitrotetrazolium chloride (75 μM). Samples were mixed with 1 mL of assay solution and exposed to a constant light intensity for 10 min. The absorbance of the supernatant at 560 nm were recorded using a flatbed scanner (infinite M200 Pro, TECAN). The absorbance of the assay solution under light and without light was recorded as positive and negative controls, respectively. O2•− scavenging ratio were evaluated according to the following formula:O2·−scavengingratio(%)=Asample−AnegativeconbtrolApositivecontrol−Anegativecontrol×100% The antioxidant capacity of the MP membranes was assessed by DPPH and ABTS experiments. For DPPH scavenging experiments, the samples were homogenized and dispersed in ethanol, followed by addition of DPPH (3.0 mL, 100 μM) and incubation for 30 min in the dark. The absorbance of the supernatant at 517 nm was recorded using a flatbed scanner. The DPPH radical scavenging ability was calculated according to the following formula:DPPHscavenging(%)=Acontrol−AsampleAcontrol×100%Where Acontrol is the absorption of the blank detection solution and Asample is the absorption of the sample solution. For ABTS assays, 7 mM ABTS and 2.45 mM potassium persulfate were reacted in the dark for 12 h, then the reaction solution was centrifuged and the supernatant was diluted with PBS to prepare the assay solution. The samples were mixed with 1 mL of ABTS assay solution and react for 10 min in the dark. The absorbance of the supernatant at 734 nm was recorded using a flatbed scanner. Intracellular ROS scavenging determination The DCFH-DA assay was used to assess intracellular ROS scavenging determination. C2C12 cells were seeded into 24-well plates at a density of 1 × 105 cells/mL. The cells were then stimulated with 500 μM H2O2 for 2 h, followed by the addition of PCL or MP membranes and further incubation for 24 h. PBS treatment was used as the control group. The intracellular ROS levels were measured by DCFH-DA probe method according to the manufacturer's instructions. Fluorescence images were taken using ImageXpress Micro Confocal (Molecular Devices, USA). Quantitative Real-time PCR analysis The effect of scaffolds on myogenic differentiation of primary muscle cells was investigated by analyzing myogenic genes (MyoG and MyoD), as well as myosin heavy chain (MHC) gene expression. Briefly, primary muscle cells were seeded into 24-well plates (2 × 104 cells/well) and incubated for 24 h. Then, the medium was exchanged with differentiation medium containing PCL and MP membranes, respectively. Cells incubated with differentiation medium were used as control group. The differentiation medium was refreshed every other day. Total RNA was extracted using TRIzol reagent (R411, Vazyme) according to the instructions. RNA concentration was measured using a Nanodrop detector (Thermo Fisher, USA) and adjusted to 200 ng μL−1. RNA was reverse transcribed to cDNA by using a reverse transcription kit (Vazyme, CHN). Real-time PCR was performed using SYBR Green reagent (Vazyme, CHN) on a fluorescence quantitative PCR instrument (CFX Opus 96, Bio-Rad). Primer sequences are shown in Table S1. The expression levels of the genes were calculated by threshold cycle (2−ΔΔCt) method. The results were normalized with GAPDH. To evaluate the effect of scaffolds on macrophage (M0) phenotype, the scaffolds were cultured with RAW 264.7 cells. RAW 264.7 cells were seeded in 6-well plates at a density of 2 × 105 cells/well and cultured overnight. For the investigation of M1 and M2 phenotypic differentiation, lipopolysaccharides (LPS) and IL-4 were used for stimulation, respectively. After 2 days of culture, RNA was extracted and the expression of related genes was detected according to the above procedures. Establishment of VML model and histological examination We evaluated the effect of scaffolds on skeletal muscle regeneration using a rat model of anterior tibial (TA) VML. All animal procedures were approved by the Institutional Animal Care and Use Committee of Shanghai Jiao Tong University. Female SD rats (180 g to 200 g, n = 4) were purchased from Shanghai SLAC Laboratory Animal Co., LTD. Female Sprague-Dawley rats were chosen for this study to avoid the potential confounding effects of aggressive behavior and fighting-induced injuries commonly observed in male rats when housed in groups, which could independently affect muscle repair and inflammatory responses. Additionally, female rats have been widely used in previous VML studies, allowing direct comparison with the literature [37,38]. Rats were anesthetized using isoflurane in a gas anesthesia machine (Shenzhen ruiwode Life Technology Co., Ltd, CHN). The skin was cut to expose the tibialis anterior muscle, creating a cuboid shaped defect (10 mm × 5 mm, approximately 30% - 40% of the weight of the muscle was removed). The scaffold was transplanted to fill the defect area. The skin was closed by 6-0 nylon suture (Pudong Jinhuan Medical) and sterilized with iodophor. No treatment was performed as the control group. The same surgical procedure was performed (skin incision, fascia incision, and exposure of the tibialis anterior muscle) in sham-operated group, but no muscle tissue was excised (i.e., no VML defect created). The incision was then closed identically to the other groups. The rats were then sacrificed at 8 weeks after operation and the TA muscles on both sides were photographed and weighed. Muscles were then fixed in 4% (v/v) formaldehyde solution, embedded, and sectioned. Hematoxylin-eosin (HE) staining, Masson's trichrome staining, and immunohistochemical staining of CD31 were performed. The sections of the specimens were stained with immunofluorescence, including COL-I, MHC, laminin, CD206, α-SMA and β-III-tubulin. The digitized information was analyzed using ImageJ software. Evaluation of muscle motor function recovery 8 weeks after operation, the rats were placed on the small animal running platform (XR-PT-10B, Shanghai shxinruan Technology Co. LTD, CHN) for running test. The running postures and running time of rats in each group were recorded. To better evaluate the recovery of motor function in rats, the animals were placed on the CatWalk gait analysis system (Noldus Information Technology, Wageningen, The Netherlands) at 3, 6, and 8 weeks post-surgery. The rats were trained to walk along a corridor, and their footprints were recorded. Motor function recovery was assessed by analyzing the footprint area and average walking speed. Statistical analysis For HE and Masson images, the minimum (Min.) Feret's diameter (the shortest axis across the center of the myofiber) of centrally nucleated myofibers was measured and statistically analyzed to determine myofiber size. For Masson, iNOS, CD68, and CD206 staining, image analysis was performed using Image-J software (NIH), and the results were normalized to the positive area for statistical calculation. For CD31 and α-SMA images, the numbers of CD31+ and SMA+ vessels (only those with a discernible lumen) were counted within the regenerated area to obtain vessel density. The regenerated area was primarily defined as the region containing myofibers with centrally located nuclei. For βIII-tubulin+ images, the regenerated area was similarly used to count positive profiles to determine nerve density. All data were expressed as mean ± standard deviation (SD). All experiments were performed in triplicate (n = 3) unless otherwise stated. GraphPad Prism 8 software and Origin 8.5 software were used for statistical analysis. Image-J software (NIH) was used for image analysis. One-way ANOVA was used for comparison among multiple groups, and p < 0.05 was considered statistically significant. Results and discussion Construction and characterization of MPHP scaffolds From Fig. 1A, TEM images showed that the Ti3C2Tx MXene nanosheets are few-layer. XPS can provide element-specific information about the electronic structure of the examined components. Fig. 1B showed the survey XPS of Ti3C2Tx MXene and Ti 2p XPS of Ti3C2Tx MXene for the core levels. The presence of chlorine in Fig. 1B (a) may be caused by etching or delamination. The Ti 2p XPS spectrum in Fig. 1B (b) shows little indication of TiO2 formation. XPS spectra of the C 1s, Ti 2p, O 1s, and F 1s core levels of Ti3C2Tx are depicted in Fig. S1. The spectra of F 1s and O 1s in Fig. S1 (a) and (b) are strong and clear. Fig. S1 (d) shows a sharp C 1s at 282.35 eV and comparatively very small amount of graphite-like carbon at 284.80 eV. This indicates that the prepared Ti3C2Tx MXene is of good quality.Fig. 1Characterization of PHP and MPHP scaffolds (A) TEM images of Ti3C2Tx MXene. (B) a). XPS electron spectroscopy for Ti3C2Tx MXene, b) The Ti 2p XPS electron spectroscopy of Ti3C2Tx MXene for the core levels. (C) SEM images of nanofiber membranes. (D) EDS elemental mapping images of MP nanofiber membranes. (E) Water contact angles of PCL and MP nanofiber membrane with different contents. (F) Stress-strain curves of PCL and MP nanofiber membranes. (G) 1H NMR spectra and (H) FTIR spectrum of HA and HA-CA. (I) SEM images of HP hydrogels. (J) Swelling ratio of the HP hydrogels in PBS, n = 3. (K) Oscillatory frequency sweep tests of HP hydrogels at a fixing strain of 0.5%. (L) Cumulative release of Ti3C2Tx from the MP electrospun membrane. (M) Degradation behavior of MPHP scaffold in vivo. Characterization of PHP and MPHP scaffolds (A) TEM images of Ti3C2Tx MXene. (B) a). XPS electron spectroscopy for Ti3C2Tx MXene, b) The Ti 2p XPS electron spectroscopy of Ti3C2Tx MXene for the core levels. (C) SEM images of nanofiber membranes. (D) EDS elemental mapping images of MP nanofiber membranes. (E) Water contact angles of PCL and MP nanofiber membrane with different contents. (F) Stress-strain curves of PCL and MP nanofiber membranes. (G) 1H NMR spectra and (H) FTIR spectrum of HA and HA-CA. (I) SEM images of HP hydrogels. (J) Swelling ratio of the HP hydrogels in PBS, n = 3. (K) Oscillatory frequency sweep tests of HP hydrogels at a fixing strain of 0.5%. (L) Cumulative release of Ti3C2Tx from the MP electrospun membrane. (M) Degradation behavior of MPHP scaffold in vivo. Fig. 1C shows the SEM images of PCL and MP nanofiber membranes. The nanofibers have a smooth surface and are evenly distributed. Fig. 1D shows elemental mapping images of 1% MP nanofiber membrane. The Ti elements image shows dense bright spots, indicating that Ti3C2Tx MXene were encapsulated in PCL nanofibers. The effective encapsulation of Ti3C2Tx MXene can protect it from direct contact with oxygen and water, so that its activity is well preserved for long-term function. The elemental analysis of 0.5% MP and 2% MP membrane were shown in Fig. S2, which shows bright spots of different densities, indicating the content and distribution of Ti3C2Tx in the PCL nanofibers. The water contact angle results of PCL and MP nanofiber membranes with different contents showed that they were hydrophobic. The PCL contact angle was 138.96° ± 1.05°, the contact angles of 0.5% MP, 1% MP, and 2% MP were 138.93 ± 3.16°, 138.87 ± 2.03°, and 134.47 ± 3.63°, respectively (Fig. 1E). The addition of Ti3C2Tx did not significantly reduce the water contact angle of the membranes, which also indicated that Ti3C2Tx was successfully spun into the fiber. In addition, a small number of Ti3C2Tx with larger particle sizes were surrounded by the spun fiber bundles. This part of the Ti3C2Tx MXene works first, the Ti3C2Tx embedded in the fiber will gradually be released over time. The mechanical properties of the membranes were evaluated by tensile testing (Fig. 1F). Both PCL and MP membranes with different contents had good ductility. Among them, 0.5% MP had the highest stress strength of 8.34 MPa and tensile strain at break of 336.8%. PCL had the lowest stress of 2.08 Mpa. The stress-strain curves of 1% MP and 2% MP were similar, the stress was 4.57 MP and 4.55 MPa, and the tensile strain at break was 246.3% and 260.0%, respectively. As the content of Ti3C2Tx further increased to 5%, the stress strength of the membrane increased to 4.99 MPa, while its tensile strain at break decreased to 139.5%. It indicates that the addition of Ti3C2Tx can significantly increase the strength of the membrane, but with the further increase of the content, the mechanical strength of the membrane decreases instead. The HA-CA structure was confirmed by 1H NMR spectra (Fig. 1G) and FTIR spectrum (Fig. 1H). The peaks at δ 6.75-6.95 ppm correspond to the H in the aromatic ring, and the peaks at δ 2.9 and 3.1 ppm correspond to the catechol methylene-proton peak, all of which indicate the successful binding of dopamine to HA. Compared with the FTIR spectrum of HA, HA-CA showed a peak at 1728 cm−1, which may be the vibrational absorption peak of −COOH. The strong absorption peak of HA-CA at 1559 cm−1 was formed by N-H bending vibration of amide II band. In addition, the intensity of the asymmetric and symmetric tensile vibrations of −COONa at 1601 cm−1 and 1406 cm−1 were significantly reduced. These confirm the successful formation of a chemical coupling between HA and CA via an amide bond. The microscopic images of HP hydrogels are shown in Fig. 1I. Both 1% HP and 2% HP hydrogels were loose and porous. From the swelling curve of the hydrogel (Fig. 1J), the HP hydrogel underwent rapid swelling in the first 3 h and basically maintained swelling equilibrium after 12 h (1% HP: 18.24 ± 1.70%; 2% HP: 27.48 ± 3.39%). The mechanical properties of the hydrogel were investigated by dynamic rheological analysis (Fig. 1K). The storage modulus (G’) of 1% HP and 2% HP hydrogel was about 165 Pa and 275 Pa, respectively. With the increase of HA-CA content, the crosslinking degree of the hydrogel increased, and its mechanical strength also increased. Considering that pore size is particularly important for the transport of waste and the transport of oxygen, 1% HP was chosen was selected as the scaffold. The cumulative release of Ti3C2Tx from the electrospun membrane at day 60 was 7.4 ng (Fig. 1L), lower than expected. Given the differences in the release medium and the fact that the in vivo microenvironment promotes scaffold degradation, the actual release in vivo is expected to exceed that observed in vitro [39,40]. At day 60, the scaffold had degraded by 58.86% in vivo (Fig. 1M). Examination of the explanted scaffolds at this time point revealed that the hydrogel was almost completely degraded, whereas a small amount of the electrospun membrane remained, suggesting that the membrane can also be fully degraded at later stages [41,42]. Biocompatibility and antioxidant efficacy of the MPHP scaffolds The appearance of the scaffold is shown in Fig. S3, and its layered and microscopic structure can well mimic the structure and microenvironment of native muscle. Good biocompatibility of scaffolds is a prerequisite for their effect of muscle regeneration in vivo. As shown in Fig. 2A and B, the cell viability and cell proliferation rate of the scaffolds and the control group were similar. Similar results were obtained in live or dead staining experiments (Fig. 2C), indicating that MPHP scaffolds had good cytocompatibility. In addition, the biocompatibility was also determined by seeding primary muscle cells on the nanofiber membranes. From Fig. 2D, by staining the cells on the membranes, it was found that very few cells on the membrane died. The morphology and density of cells grown on the membranes were similar to those in the control group. The size of the cells growing on the membranes were slightly smaller than that on the slide, presumably because the membrane is a 3D loose multi-layered nanofiber structure. The cells are seeded and then adhere and stretch in the fibers, so that at a particular focal plane the cells appear smaller than their actual size. Fig. S4 shows the HE staining images of heart, liver, spleen, lung and kidney of rats in each group. It can be seen from the figure that the color and tissue morphology are normal, without obvious morphological abnormalities or tissue necrosis, indicating that the scaffold has good biocompatibility in vivo.Fig. 2Biocompatibility and antioxidant capacity evaluations of the MPHP scaffolds. (A) Cell viability of C2C12 cells after incubating 24 h with PHP and MPHP scaffolds. (B) Cell viability of C2C12 cells with PHP and MPHP scaffolds for 1, 3 and 5 days. (C) Live/Dead staining images of C2C12 cells on 24h after treatment with membranes (live cells: green, dead cells: red.) (D) Live/Dead staining images of primary muscle cells culcured on PCL and MP nanofiber membranes. Free radical scavenging capacity of MP nanofiber membrane against various types of free radicals: (E) •OH, (F) O2•−, (G) DPPH, and (H) ABTS•+. (I) Fluorescence image of C2C12 cells stained with DCFH-DA probe to detect intracellular ROS levels. (J) Quantitative analysis of intracellular ROS levels. All data are presented as mean ± SD, n = 3. ∗p < 0.05, ∗∗p < 0.01, ∗∗∗p < 0.001, ∗∗∗∗p < 0.0001. (For interpretation of the references to color in this figure legend, the reader is referred to the Web version of this article.) Biocompatibility and antioxidant capacity evaluations of the MPHP scaffolds. (A) Cell viability of C2C12 cells after incubating 24 h with PHP and MPHP scaffolds. (B) Cell viability of C2C12 cells with PHP and MPHP scaffolds for 1, 3 and 5 days. (C) Live/Dead staining images of C2C12 cells on 24h after treatment with membranes (live cells: green, dead cells: red.) (D) Live/Dead staining images of primary muscle cells culcured on PCL and MP nanofiber membranes. Free radical scavenging capacity of MP nanofiber membrane against various types of free radicals: (E) •OH, (F) O2•−, (G) DPPH, and (H) ABTS•+. (I) Fluorescence image of C2C12 cells stained with DCFH-DA probe to detect intracellular ROS levels. (J) Quantitative analysis of intracellular ROS levels. All data are presented as mean ± SD, n = 3. ∗p < 0.05, ∗∗p < 0.01, ∗∗∗p < 0.001, ∗∗∗∗p < 0.0001. (For interpretation of the references to color in this figure legend, the reader is referred to the Web version of this article.) Because of the excellent antioxidant activity of Ti3C2Tx MXene, we performed a series of free radicals scavenging and antioxidant experiments to determine the antioxidant activity of the prepared scaffolds. From Fig. 2E–H, the scavenging rate for ·OH, O2·-, DPPH and ABTS·+ of MP were significantly higher than control and PCL. In addition, DCFH probe assay was performed to determine the scavenging efficiency of the scaffolds on intracellular ROS (Fig. 2I). First, the ROS fluorescence intensity was significantly increased in C2C12 cells when exposed to H2O2 to induce oxidative stress. After incubation with the Ti3C2Tx scaffold, the fluorescence intensity was significantly reduced, much lower than that of the H2O2 stimulation group. This result was also confirmed by quantification of intracellular fluorescence intensity (Fig. 2J). Morphological observation of the defect TA muscle and assessment of the regeneration effect Fig. 3A shows the establishment of a rat VML model of TA muscle and the implantation of the scaffold. The TA muscle of the surgical side was removed at 8 weeks after the operation, photographed and weighed compared with the contralateral TA muscle. From Fig. 3B, we found that the untreated group had significant muscle atrophy, residual large defects, and overall slender muscles. However, the scaffold group obviously showed different degrees of muscle regeneration. It is speculated that the implantation of a biocompatible scaffold including HP hydrogel and PCL nanofibers could mimic the extracellular matrix environment and provide a supporting space for cells to adhere and grow [43]. In addition, the muscles in the MPHP scaffold group were fuller and the gap was smaller compared with the muscles in the normal side. From Fig. 3C, the weight ratio of the TA muscle on the operated side to the contralateral side reached 93.73 ± 3.63%, while the muscle ratio of the control group was only 84.97 ± 5.82%.Fig. 3Assessment of the in vivo muscle regeneration effect of scaffolds in TA VML model. (A) The establishment of rat TA VML model and transplantation of scaffold. (B) The photograghs of the reconstructed TA muscles compared with that of the contralateral muscles at 8 weeks. (C) The ratio of TA muscle weight between the defective leg and contralateral normal leg. (D) HE and Masson's trichrome stained images of injury site at 8 weeks after VML surgery. Scale bar: 25 μm. (E) Statistic of the percentage of centronucleated muscle fibers area to total section area. (F) Quantification of the fibrotic area in the de novo formed muscle based on Masson stained images. (G) Frequency distribution of Min. Feret's diameter. (H) Average Min. Feret's diameter of centronucleated muscle fibers. All data are presented as mean ± SD, n = 4. ∗p < 0.05, ∗∗∗p < 0.001. Assessment of the in vivo muscle regeneration effect of scaffolds in TA VML model. (A) The establishment of rat TA VML model and transplantation of scaffold. (B) The photograghs of the reconstructed TA muscles compared with that of the contralateral muscles at 8 weeks. (C) The ratio of TA muscle weight between the defective leg and contralateral normal leg. (D) HE and Masson's trichrome stained images of injury site at 8 weeks after VML surgery. Scale bar: 25 μm. (E) Statistic of the percentage of centronucleated muscle fibers area to total section area. (F) Quantification of the fibrotic area in the de novo formed muscle based on Masson stained images. (G) Frequency distribution of Min. Feret's diameter. (H) Average Min. Feret's diameter of centronucleated muscle fibers. All data are presented as mean ± SD, n = 4. ∗p < 0.05, ∗∗∗p < 0.001. HE staining and Masson trichrome staining were used to observe the histological characteristics of TA muscle cross section. Excessive fibroblast infiltration will lead to a large amount of collagen deposition, forming scars and limiting the contractile function of muscles [44,45]. As shown in Fig. 3D, the untreated group showed marked scarring and disorganized muscle fibers. Both PHP and MPHP scaffold groups showed significant muscle recovery. However, the muscle fibers in the PHP group were thinner and arranged as disorderly as those in the non-repaired group. The muscle fibers in the MPHP scaffold group were uniform in size and ordered in distribution, which were similar to the uninjured area. We also evaluated the area of regenerating myofibers with central nuclei. The percentage of nucleated muscle fibers in the total cross-sectional area of the MPHP scaffold group was 14.74 ± 4.13%, which was significantly lower than that of the control group (36.43 ± 8.15%) (Fig. 4E), indicating that the muscle fibers were more mature [46,47]. The fibrosis level of regenerated muscle tissue calculated by Masson images showed that the fibrosis level of the scaffold group was significantly lower than that of the other two groups (2.66 ± 0.49), while the fibrosis level of the PHP scaffold group and the control group was 7.31 ± 0.98% and 9.45 ± 0.86%, respectively (Fig. 4F). Moreover, the fibrosis level in the MPHP scaffold group was close to that of the sham group, with no statistically significant difference. This indicates that the MPHP scaffold significantly reduces the fibrosis that may occur in the injured area.Fig. 4Quantitative RT-PCR analysis for (A) MyoD gene, (B) MyoG gene and (C) MYH1 gene of primary muscle cells coculcured with PHP and MPHP scaffolds. (D) Immunofluorescence staining of muscle for COL-I, laminin and MHC in different groups at 8 weeks. COL I and MHC in green, laminin in red, and nuclei in blue. Scale bar: 50 μm. Data are presented as mean ± S.D, n = 4. ∗p < 0.05, ∗∗p < 0.01, ∗∗∗∗p < 0.0001. (For interpretation of the references to color in this figure legend, the reader is referred to the Web version of this article.) Quantitative RT-PCR analysis for (A) MyoD gene, (B) MyoG gene and (C) MYH1 gene of primary muscle cells coculcured with PHP and MPHP scaffolds. (D) Immunofluorescence staining of muscle for COL-I, laminin and MHC in different groups at 8 weeks. COL I and MHC in green, laminin in red, and nuclei in blue. Scale bar: 50 μm. Data are presented as mean ± S.D, n = 4. ∗p < 0.05, ∗∗p < 0.01, ∗∗∗∗p < 0.0001. (For interpretation of the references to color in this figure legend, the reader is referred to the Web version of this article.) The distribution and orientation of muscle fibers in the MPHP group were more ordered and regular than those in the unrepaired group and the PHP scaffold, which were closer to the uninjured muscle fibers. The Min. Feret's diameter and its frequency of the nascent muscle fibers could be quantitatively determined by HE and Masson staining, which can be used to assess the morphological and structural maturation of the regenerated muscle. The Min. Feret's diameter distribution showed that muscle fibers were mainly 20-30 μm in the untreated group, 25-35 μm in PHP scaffold group, and 35-55 μm in MPHP group (Fig. 4G). The average myofiber diameter in the MPHP group was 44.40 ± 15.50 μm, which, although still smaller than that in the sham group (55.29 ± 12.00 μm), was significantly larger than those in the other two groups (Fig. 4H). The average myofiber diameters in the untreated group and the PHP scaffold group were 31.09 ± 11.29 μm and 33.41 ± 11.17 μm, respectively. These results indicate that the MPHP scaffold promotes faster and more mature myofiber regeneration. Promote myogenic differentiation and alignment and maturation of muscle fibers MyoD and MyoG belong to the myogenic regulatory factors (MRFs) family. MRFs act at multiple points in the muscle lineage, from coordinating myoblast proliferation, to various stages of skeletal muscle development, such as myoblast fusion and myotube maturation [[48], [49], [50], [51]]. The major component of myosin is myosin heavy chain (MyHC), the expression of which determines the contractile properties of muscle fibers, is an important protein associated with myogenic differentiation and myogenesis [52]. MYH1 is one of the isoforms encoding myosin (contractile). The primary muscle cells were cultured with different Ti3C2Tx content scaffolds in differentiation medium for 4 days, and the changes in the expression of MyoD, MyoG and MYH1 genes were detected (Fig. 4A–C). We found that the expression of above-mentioned muscle regeneration-related genes in the scaffold containing Ti3C2Tx was higher than that in the scaffold without Ti3C2Tx. In particular, the expression levels of MyoD, MyoG and MYH1 genes in 1% MPHP scaffold group were significantly higher than those in control group (>3.9-fold upregulation of MyoD and >2.9-fold upregulation of MyoG). The statistical results showed that the MPHP scaffolds could significantly promote myogenic differentiation. Type Ⅰ collagen (COL-I) constitutes the outer matrix and provides mechanical support and structural stability to muscle fibers. After muscle fiber injury, COL-I is involved in the generation of new myofibrils and tissue repair by interacting with other cells and proteins [53]. Laminin is widely distributed throughout the body, mainly in the basement membrane (BM), and plays an important role in tissue structure and maintenance, cell signaling, adhesion, and migration. The major role of laminin in muscle is to connect muscle fibers and satellite cells with other BM components such as collagen, glycoproteins, proteoglycan and glycosaminoglycan, which plays an important role in muscle regeneration and repair [54]. More evidence of muscle fiber formation was observed 8 weeks after injury by immunofluorescence staining COL-I, laminin and MHC in de novo formed muscle tissue. From Fig. 4D, we found that the COL-I deposition in the PHP and MPHP groups was more pronounced than that in the control group, and the deposition in the MPHP group was more ordered and complete. While the control and PHP groups showed less laminin, the MPHP scaffold group was more intact. The muscle morphology in MPHP group was also more similar to that of the sham group. Regulate macrophage polarization to a proregenerative phenotype The inflammatory phase is the first phase of the repair process after muscle injury and is accompanied by the upregulation of inflammatory M1 macrophages [55]. Therefore, the mRNA levels of M1 macrophage markers, pro-inflammatory cytokines TNF-α, IL-6 and IL-1β, and M2 macrophage anti-inflammatory markers CD206 and Arg-1 were detected by quantitative RT-PCR detection to determine the regulatory effect of the scaffolds on macrophages in vitro. As shown in Fig. 5A–C, the mRNA levels of TNF-α, IL-6 and IL-1β were increased upon LPS stimulation. After adjusting the mRNA level of the LPS group to 1, we found that the mRNA expression of TNF-α, IL-6, and IL-1β was significantly decreased in the MPHP scaffold groups with different contents. After IL-4 induced M2 macrophage polarization, we found that the mRNA levels of anti-inflammatory factors CD206 and Arg-1 were significantly increased in the MPHP scaffold group compared with the control group, especially in the 1% MPHP and 2% MPHP scaffold groups (Fig. 5D and E).Fig. 5Quantitative RT-PCR analysis for (A)TNF-α gene, (B)IL-6 gene, (C) IL-1β gene, (D) CD206 gene and (E) Arg1 gene of RAW264.7 cells cocultured with PHP and MPHP scaffolds. (F) Immunofluorescence staining of macrophage of muscle in different groups at 3、7 and 14 day. CD68+ in yellow, iNOS+ in green, CD206+ in red and nuclei in blue. Scale bar: 50 μm. Data are presented as mean ± S. D, n = 4. ∗p < 0.05, ∗∗p < 0.01. (For interpretation of the references to color in this figure legend, the reader is referred to the Web version of this article.) Quantitative RT-PCR analysis for (A)TNF-α gene, (B)IL-6 gene, (C) IL-1β gene, (D) CD206 gene and (E) Arg1 gene of RAW264.7 cells cocultured with PHP and MPHP scaffolds. (F) Immunofluorescence staining of macrophage of muscle in different groups at 3、7 and 14 day. CD68+ in yellow, iNOS+ in green, CD206+ in red and nuclei in blue. Scale bar: 50 μm. Data are presented as mean ± S. D, n = 4. ∗p < 0.05, ∗∗p < 0.01. (For interpretation of the references to color in this figure legend, the reader is referred to the Web version of this article.) As shown in Fig. 5F, macrophage phenotype distribution changed markedly on days 3, 7, and 14 post-surgery. M2 expression gradually increased over time in the control and PHP groups, whereas the MPHP group showed the highest M2 expression on days 3 and 7, indicating a shortened inflammatory phase and earlier transition to proliferation and repair. This is attributed to the antioxidant activity of Ti3C2Tx MXene, which reduce tissue reactive oxygen species (ROS) levels and promote M2 polarization. These results indicate that the MPHP scaffold can effectively reduce the levels of pro-inflammatory macrophages in the wound site, protect cells from excessive damage caused by inflammation and oxidative stress, promote the transformation of macrophages to M2 phenotype, and reshape the microenvironment of muscle regeneration and accelerate muscle regeneration. Promote angiogenesis, nerve innervation and recovery of exercise endurance Revascularization is essential for the structural and functional recovery of muscle regeneration because of the highly metabolic nature of skeletal muscle [56,57]. CD31 is an important marker of vascular endothelial differentiation, indicating that the vascular network of remodeling muscle is gradually established. α-smooth muscle actin (α-SMA) is normally expressed in vascular smooth muscle. Mature blood vessels are composed of endothelial cells and smooth muscle cells that stabilize vascular structure and tension. The density of CD31+ vessels and the number of α-SMA + vessels were both significantly higher in the MPHP scaffold group than in the control and PHP scaffold group (Fig. 6A–D), indicates that MPHP scaffold promotes angiogenesis and help reconstruct the vascular network. The higher density of neovascularis in the MPHP group is beneficial for gas exchange, diffusion of water and nutrients, and removal of waste products in the nascent muscle, which also explains the larger muscle fiber diameter in the MPHP group. In addition, innervation is essential for the long-term functional recovery of injured muscles [58]. The effect of MPHP scaffolds on the regeneration of muscle innervation was assessed by staining the β III-tubulin (neuronal marker). Quantitative results showed that the density of mature nerves in the regenerated area was significantly larger than that in the control group, suggesting enhanced innervation. In conclusion, we found that MPHP scaffolds could effectively reconstitute the vascular network and enhance reinnervation in the regenerated muscle, which resulted in better restoration of exercise endurance and functional activity.Fig. 6Revascularization and reinnervation after muscle regeneration and assessment of muscle functional recovery. (A) Immunohistochemical and immunofluorescence staining of muscle for CD-31, α-SMA and βIII-tubulin in different groups at 8 weeks. Statistical analysis of the density of CD31+ (B) (The red arrows denote vessels), α-SMA+ (C) (The yellow arrows denote vessels) vessels and βIII-tubulin + nerves (D) (The yellow arrows denote nerves) in the de novo formed muscle. (E) 8 weeks after surgery, the rats were placed on a conveyor belt for running, and their running posture and time were recorded. (F) Running time of rats in each group at 8 weeks. Print area (G) and run speed average (H) of rats in different groups were respectively taken at the week 3, week 6 and week 8. Data are presented as mean ± S.D, n = 4. ∗p < 0.05, ∗∗p < 0.01, ∗∗∗p < 0.001. (For interpretation of the references to color in this figure legend, the reader is referred to the Web version of this article.) Revascularization and reinnervation after muscle regeneration and assessment of muscle functional recovery. (A) Immunohistochemical and immunofluorescence staining of muscle for CD-31, α-SMA and βIII-tubulin in different groups at 8 weeks. Statistical analysis of the density of CD31+ (B) (The red arrows denote vessels), α-SMA+ (C) (The yellow arrows denote vessels) vessels and βIII-tubulin + nerves (D) (The yellow arrows denote nerves) in the de novo formed muscle. (E) 8 weeks after surgery, the rats were placed on a conveyor belt for running, and their running posture and time were recorded. (F) Running time of rats in each group at 8 weeks. Print area (G) and run speed average (H) of rats in different groups were respectively taken at the week 3, week 6 and week 8. Data are presented as mean ± S.D, n = 4. ∗p < 0.05, ∗∗p < 0.01, ∗∗∗p < 0.001. (For interpretation of the references to color in this figure legend, the reader is referred to the Web version of this article.) Finally, the running posture and running time of rats were recorded to determine whether MPHP scaffolds could promote the function recovery of limb muscle after VML of TA muscle (Fig. 6E). From the supporting video 1-3, it can be observed that the rats in the control and PHP group ran with unbalance, marked lameness and small stride length. In contrast, the body of rats in MPHP scaffolds group was more balanced and the speed was more uniform when they exercised. In terms of running time, the rats in MPHP scaffold group had significantly longer exercise time (18.6 ± 9.7 min) compared with the control (10.9 ± 5.2 min) and PHP scaffold groups(13.5 ± 5.7 min), indicating better exercise endurance (Fig. 6F). The print area ratio (LH/RH) and average run speed measured at 3, 6, and 8 weeks post-surgery also reflected, to some extent, the recovery of motor function in rats (Fig. 6G and H). In the control group, the print area ratio remained below 1 at each time point, indicating a decline in muscle function following VML, with no substantial recovery observed even at week 8. In contrast, the MPHP group exhibited a larger footprint area ratio compared to both the control and PHP groups, and this ratio was closer to that of the sham group. Regarding the average run speed, rats in the MPHP group showed an increasing trend over time, and their speeds were higher than those in the control and PHP groups. However, no statistically significant differences were observed among the four groups. The results showed that the MPHP scaffold significantly improved the motor coordination and exercise endurance of the injured hind limb in rats, indicating that the strength and function of the injured muscle were well recovered. Conclusion Ti3C2Tx MXene has great potential in the field of biomedicine due to its unique surface chemistry, excellent mechanical properties and antioxidant properties, as well as other properties. However, it is susceptible to oxidation and moisture, which greatly reduces its activity. Therefore, we designed a multifunctional MPHP nanofiber-hydrogel scaffold to mimic the native muscle structure and microenvironment by layer-by-layer stacking for VML. In vitro studies found that the scaffold protected the activity of Ti3C2Tx, which enabled it to exert antioxidant effect in vivo, effectively scavenging excessive ROS and protecting muscle from oxidative stress. Cell experiments confirmed that the scaffold could induce myoblast adhesion and growth, and significantly promote myogenic differentiation by up-regulating the relative expression of MHC, MyoD and MyoG gene during myogenesis. Both in vivo and in vitro experiments showed that the scaffold could induce the transformation of macrophages into M2 type, thereby reshaping the microenvironment of muscle regeneration and promoting the regeneration process. We found that the scaffold could promote muscle fiber regeneration and maturation, reduce fibrosis and the risk of scar formation, and effectively promote skeletal muscle regeneration in the rat model of VML in vivo. Moreover, by enhancing the reconstruction of vascular network and restoring re-innervation, the overall structure and function of muscle are restored, and the exercise endurance of the regenerated muscle is enhanced. One limitation of this study is that only female rats were used. Given known sex differences in immune function and skeletal muscle regeneration, the results may not fully translate to male subjects. Future studies should include both sexes to assess the generalizability of the scaffold's therapeutic effects. To contextualize the performance of the MPHP scaffold, its functional and histological outcomes were compared with representative biomaterial-based strategies for VML repair reported in the literature. The mushroom-derived decellularized scaffold (md-CdM) supported the formation of mature, centronucleated myofibers, significantly reduced fibrosis, improved organized microvasculature, and enhanced locomotor performance and muscle strength [59]. The microporous annealed particle (MAP) hydrogel with cell-scale porosity supported the formation of innervated myofibers and neuromuscular junctions (NMJs), indicating functional neuromuscular recovery, demonstrating potential for functional restoration after VML injury [60]. In this comparison, we note that the MPHP scaffold, without cell seeding or minced muscle supplementation, reached 93.73 ± 3.63% muscle mass restoration, a myofiber diameter of 44.40 ± 15.50 μm (comparable to the sham group's 55.29 ± 12.00 μm), and a remarkably low fibrosis area of 2.66% ± 0.49%. While acknowledging the inherent limitations of cross-study comparisons due to differences in animal models, defect locations, injury volumes, and evaluation time points, the MPHP scaffold exhibits competitive regenerative performance, particularly in fibrosis suppression and myofiber maturation. Therefore, this scaffold is expected to be used as an ideal scaffold model for skeletal muscle defect regeneration in the field of tissue regeneration, and provides a way to protect the activity of Ti3C2Tx MXene and broaden its application possibilities. Availability of data and materials The datasets used and/or analyzed during the current study are available from the corresponding author on reasonable request. Ethics approval and consent to participate All animal experiments were carried out in accordance with the National Research Council's Guide for the Care and Use of Laboratory Animals and were directed by the Institutional Animal Care and Use Committee of Shanghai Jiao Tong University (License No. A2023195-002). Consent for publication All authors have agreed to publish this article. CRediT authorship contribution statement Yihui Zhang: Data curation, Formal analysis, Investigation, Methodology, Validation, Writing – original draft. Wenkai Zhang: Data curation, Formal analysis, Resources, Software. Zeyuan Xie: Data curation, Validation, Visualization. Wei Yu: Resources, Software, Validation. Xiangqi Zhang: Resources, Software, Validation. Yangwen Luo: Software, Validation, Visualization. Muge Gu: Validation, Visualization. Jiayu Wang: Validation, Visualization. Wei-En Yuan: Conceptualization, Funding acquisition, Methodology, Project administration, Resources, Supervision, Writing – review & editing. Yebin Qian: Funding acquisition, Project administration, Resources, Supervision. Declaration of competing interest The authors declare no conflicts of interest.