Observer-based prescribed-time lag bipartite consensus of nonlinear multi-agent systems under event-triggered mechanism Authors: Jialong Tian, Tao Li, Xiaowen Zhao, Yuanmei Wang, Haiyang Hua, Le Yan, Hongru Ren, Hongru Ren Published: 2026 ABSTRACT Considering the complexity of lag time and the convergence time, as well as the influence of the observer and the event-triggered mechanism, the prescribed-time lag bipartite consensus (PTLBC) control problem for nonlinear multi-agent systems (MASs) is researched in the paper. First of all, it designs the prescribed-time dynamic observer (PTDO) for followers to get the states of the leader within an arbitrarily prescribed time. Furthermore, to significantly decrease the communication consumption, the innovative event-triggered mechanism is studied for followers. To realize the lag bipartite consensus (LBC) of nonlinear MASs within an arbitrarily prescribed time, a PTLBC control scheme is presented via the aforementioned PTDO and event-triggered mechanism. With Lyapunov stability analysis method, sufficient conditions are obtained and detailed stability analysis is studied, which indicates that the nonlinear MASs can realize PTLBC. Furthermore, the analysis proves that the proposed event-triggered mechanism excludes Zeno behaviour. The theoretical analysis is validated by means of a simulation example. 1. Introduction Recently, the cooperative control of MASs has been extensively studied across numerous scientific fields, including urban transportation scheduling, distributed power generation, and unmanned aerial vehicles formation control, etc.[1–8]. As a primary problem in the cooperative control of MASs, consensus control has achieved many significant results [9–15]. Lag consensus, as an unusual case of consensus, has recently attracted considerable attention for its utilisation in preventing congestion [16–19]. Assuming to be a lag time, lag consensus denotes that the followers’ states at time are same as the leader’s states at time. The asymptotic stability of lag consensus has been studied for MASs [16–19]. However, the asymptotic lag consensus cannot satisfy the requirements of practical engineering applications. Finite-time lag consensus (FNTLC) control has recently gained attention for enhancing the convergence speed of the MASs [20–22]. However, FNTLC control is subject to initial states of MASs. For resolving the problem, fixed-time lag consensus (FXTLC) control has been presented [23–26]. But FXTLC control depends upon the control protocol parameters. To address the issue, prescribed-time lag consensus (PTLC) control has been proposed. The prescribed-time lag consensus control protocol makes the arbitrary assignment of convergence time possible, which is independent of both the controller parameters and the initial states of the agents. Obviously, PTLC has important academic value and practical significance. The problem of prescribed-time partial component lag consensus of MASs subject to both disturbances and switching topologies is investigated [27]. A PTLC control scheme with adaptive gains for lag consensus is introduced [28]. It should be noted that the above works, including [27,28], all assume that the communications among agents are continuous. However, continuous communication results in excessive resource consumption and may compromise the system’s stability due to the limited computational capabilities and storage capacity in applications. Obviously, this research of discontinuous communication control protocols is important. To reduce resource consumption, a control scheme for successive lag consensus of nonlinear MASs is presented based on event-triggered mechanism with both constant and time-varying lag consensus scenarios [29,30]. By a novel static event-triggered mechanism, reference [31] designs a control protocol to research the lag consensus of MASs. Reference [1] develops a dynamic memory event-triggered mechanism to research the lag consensus control of multi-unmanned aerial vehicle systems under hybrid attacks. The aforementioned studies have effectively addressed the resource constraint of agents in practical scenarios using event-triggered mechanisms, but they rarely consider the convergence time at the same time. It is more challenging to create a control scheme for reducing resource consumption while setting the prescribed convergence time at will for the lag consensus control problem. Notably, the aforementioned works about lag consensus have primarily considered cooperative relationships while neglecting competitive relationships within agents. However, competitive relationship is widely present in natural systems, social and engineering systems. In MASs, cooperation and competition often coexist. Motivated by competitive relationships and lag consensus, the problem of lag bipartite consensus is presented [32–35]. Reference [34] investigates the LBC control problem of linear MASs under saturating input, but utilizes continuous communication control protocol. Using the event-triggered mechanism, reference [35] discusses the LBC control of nonlinear MASs with external disturbances, but just considers the asymptotic convergence. Significantly, the aforementioned studies on LBC assume that the leader’s states are available. Obviously, it is unrealistic in numerous practical applications. So, to devise an observer is important for estimating the states of leader. In light of the discussions above, the paper comprehensively studies the PTLBC of nonlinear MASs via the PTDO and event-triggered mechanism. The main contributions of this paper are summarized as follows: 1)Different from the system investigated in [36], this paper studies a second-order integrator system with nonlinear components, which extends the research scope of relevant works. Different from the system investigated in [36], this paper studies a second-order integrator system with nonlinear components, which extends the research scope of relevant works. 2)Different from the method adopted in [28], this paper proposes a novel event-triggered mechanism by combining the prescribed-time time-varying function with the measurement error. Different from the method adopted in [28], this paper proposes a novel event-triggered mechanism by combining the prescribed-time time-varying function with the measurement error. 3)Considering that follower agents cannot directly access the state of the leader agent, a prescribed-time dynamic observer is designed to estimate the leader’s state information. Considering that follower agents cannot directly access the state of the leader agent, a prescribed-time dynamic observer is designed to estimate the leader’s state information. 4)To address the problem of communication congestion, a prescribed-time lag-bipartite consensus control protocol based on the event-triggered mechanism is designed by integrating prescribed-time control with the event-triggered mechanism. To address the problem of communication congestion, a prescribed-time lag-bipartite consensus control protocol based on the event-triggered mechanism is designed by integrating prescribed-time control with the event-triggered mechanism. This paper is organized into the following chapters: The problem statement and preliminaries are shown in Section 2. Section 3 proposes a novel PTDO, studies an innovative event-triggered mechanism, develops a PTLBC control protocol to realize LBC within the arbitrarily prescribed time, and discusses the Zeno behaviour in detail. The theoretical results are validated through a numerical example in Section 4. Section 5 gives the conclusions. 2. Preliminaries and problem statement 2.1. Graph theory Let ℝq be the set of the q×1 real vectors, Iq be the q order identity matrix, and ℝq×q be the set of q×q real matrices. sign(·) is the sign function. ∥·∥ is the Euclidean norm. The binary operator ⊗ represents the Kronecker product. λmin(H) and λmax(H) denote the minimum and maximum eigenvalues of the symmetric matrix H, separately. The followers’ connected topology of the nonlinear MASs is typically represented with a directed signed graph 𝒢={𝒱,ℰ,𝒜}. Let 𝒱={v1,...,vn} be the set of followers, ℰ⊆𝒱×𝒱 be the set of edges, and 𝒜=[aij]∈ℝn×n be the adjacency matrix. If ℰij∈ℰ, then aij≠0, otherwise, aij=0. aij<0 indicates the competitive relationship between the i-th follower and j-th follower, while aij>0 represents the cooperative relationship between the i-th follower and j-th follower. L=[lij]∈ℝn×n is the Laplacian matrix of 𝒢, satisfying lij=−aij for i=j, and lij=∑j=1N|aij| for i≠j. Furthermore, the interaction directed signed graph 𝒢~={𝒱~,ℰ~,𝒜~} describes the connected topology of the whole system. Let 𝒱0={v0} be the leader’s set. Define 𝒱~=𝒱∪𝒱0. The set 𝒱~ is partitioned into a pair of disjoint subsets 𝒱~1 and 𝒱~2. The matrix B=diag(b1,b2,...,bn) describes the relationship between the followers and the leader. When there is a connection from the leader to i-th follower, bi=1; otherwise, bi=0. 2.2. Some assumptions and lemmas The section lists the useful assumptions and lemmas. Assumption 1 ([26]). Let the graph 𝒢 be structurally balanced. There is a spanning tree rooted at the leader in the graph 𝒢~. Assumption 2 ([37,38]). There always exist positive real numbers cx and cv satisfying the below equation, where vectors n,m,n―,m―∈ℜq. Lemma 1 ([14]). If there is a matrix θ=diag{σ1,σ2,...,σn}, where σi∈{1,−1}, and all elements of 𝒜~=θT𝒜θ are greater than or equal to zero, where θT=θ−1=θ, then the structural balance of the directed signed graph 𝒢 holds. Lemma 2 ([19]). The below inequality is true where y, z are any given vectors with proper dimensions and l is a positive constant. Lemma 3 ([26]). If there is a positive define matrix Ξ=diag(ξi)=diag(xi/yi), then Q=+HTΞ is positive define,where the vectors yi=[y1,y2,\ldots,yn]T=H−T1n,xi=[x1,x2,\ldots,xn]T=H−11n and H=L+B. Lemma 4 ([26]). Analyze the following systems where z(t)∈ℝq is the state, f(·,·) is the time-bounded vector and f(0) indicates the system initial state. The time-varying function below is first introduced [36]. and ψ(t)=1, t≥t0+T, in which ρ>1, T>0 is a prescribed time, and t0>0 is the initial time. Ψ(t) is defined as For system, if there is a Lyapunov function V(t) which satisfies where Ψ(t) is defined in, c≥0and k>0, then the system is prescribed-time stable with the prescribed time t0+T. It can get the solution below. Lemma 5 ([38]). For system,if there exist a continuously differentiable and positive-definite function V(t), two positive constants n1> 0, n2> 0, and a scalar n3 satisfying (1/h)−n10, if the solution of and satisfies and then the PTLBC is said to be achieved for the nonlinear MASs and, where σi is defined in Lemma 1. 3. Main results 3.1. The design of PTDO Suppose Assumption 1 holds. For the followers, the PTDO below is designed to estimate the states information of the leader. where Here, the estimate of the leader state x0 and v0 are denoted as ϑxi and ϑvi, respectively. β is the observer gains, Ψι(t) is as follows where ψι(t)=(ιTιT+t0−t)ρ, t≥t0+ιT and ι(∀ι=1,2,3). Set three times T1, T2, and T3, where T1=t0+T and T2=t0+2T represent the prescribed convergence time of the position states and velocity states for the state observer, respectively; T3=t0+3T denotes the prescribed convergence time of the closed-loop nonlinear system under the proposed controller. Theorem 1. For the PTDO, estimation errors are categorised into velocity errors ϑ―vi(t)=ϑvi(t)−σiv0(t) and position errors ϑ―xi(t)=ϑxi(t)−σix0(t). If β>λmax(Ξ)/λmin(Q), c≥0, k>0 and h>1, then ϑ―xi and ϑ―vi will converge to zero within the prescribed time T1=t0+T and T2=t0+2T, respectively. Proof. The convergence analysis of prescribed time dynamic observer will be implemented by the following two steps. (1)For convenience, let ϑxi(t) be ϑxi, and ϑvi(t) be ϑvi. Considering the observer error ϑ―vi, by differentiating the first equation in, we obtain ϑ―˙v=−β(k+cΨ1(t))(H⊗Ir)ϑ―v. Selecting the following Lyapunov function For convenience, let ϑxi(t) be ϑxi, and ϑvi(t) be ϑvi. Considering the observer error ϑ―vi, by differentiating the first equation in, we obtain ϑ―˙v=−β(k+cΨ1(t))(H⊗Ir)ϑ―v. Selecting the following Lyapunov function the derivative of V1 is as follows From (14), it can be obtained that −1/2λmax(Ξ)ϑ―vTϑ―v≤−V1≤−1/2λmin(Ξ)ϑ―vTϑ―v. It concludes that −ϑ―vTϑ―v≤−2/λmax(Ξ)V1. Then, substituting these inequalities into, it obtains where −βλmin(Q)/λmax(Ξ)≤−1, i.e., β≥λmax(Ξ)/λmin(Q). Especially, the following solution can be obtained In other words, within the arbitrarily prescribed time T1, ϑ―vi converges to zero according to Lemma 4. (2)Similar to the derivation processes of Equations (14) and (15) and, it obtains that within the arbitrarily prescribed time T2, ϑ―xi will converge to zero. That is to say, the PTDO (12) is effective. Similar to the derivation processes of Equations (14) and (15) and, it obtains that within the arbitrarily prescribed time T2, ϑ―xi will converge to zero. That is to say, the PTDO (12) is effective. 3.2. Event-triggered mechanism The innovative event-triggered mechanism is devised in the section. For simplicity, let x0(t−τ) be x0τ(t), v0(t−τ) be v0τ(t), ϑxi(t−τ) be ϑxiτ(t), and ϑvi(t−τ) be ϑviτ(t). Define the lag bipartite consensus error as x―i(t)=xi(t)−σix0τ(t) and v―i(t)=vi(t)−σiv0τ(t), respectively. Let two auxiliary states be Then, let ηi(t)=k1}\lower0.5em\smash⌢$xi(t)+k2}\lower0.5em\smash⌢$vi(t), where k1>0, k2>0. Let Ψ~3(t)=Ψ˙3(t)/Ψ3(t) for t0≤t0, α>0, γi>0 are positive constants, and ψ(t) defined in (2). If hi(t)≥0, the position xi(tki) and velocity vi(tki) are update to xi(tk+1i) and vi(tk+1i), and transmitted to the MASs, where 3.3. PTLBC control protocol Via the above event-triggered mechanism and PTDO, the PTLBC control protocol is designed. For t0≤t0 and Ψ3(t) corresponds to the case when ι=3 in (3). Besides, tki represents the triggering time of the k-th event for the follower i, where t0i =0. For t∈[tki,tk+1i), xi(tki) and vi(tki) record the transmission states of follower i at tki. When t≥T2, the ϑxiτ(tki) and ϑviτ(tki) transition to x0τ\hspace{0.5em}(tki) and v0τ(tki) in the control protocol (19). Then, it obtains Taking the derivative of x⌢it, one gets Consequently, we obtain the feedback control system of (8) and (9) together with (19) and (21) as The system (22) has the concise form below, where ℱ(t)=G(t,x,v)−1n⊗g(t,x0τ,v0τ), G\hspace{0.5em}(t,\hspace{0.5em}x,\hspace{0.5em}v)\hspace{0.5em}=[gT\hspace{0.5em}(t,\hspace{0.5em}x1,\hspace{0.5em}v1),gT(t,\hspace{0.5em}x2,\hspace{0.5em}v2)\hspace{0.5em},...,\hspace{0.5em}gT(t,\hspace{0.5em}xN,\hspace{0.5em}vN)]T, x⌢=x⌢1T, x⌢2T, x⌢NTT, v⌢=v⌢1T, v⌢2T, v⌢NTT, x=[x1T,x2T,...,xNT]T, and v=[v1T,v2T,...,vNT]T. Substituting state measurement error e(t) into (23), it has Theorem 2. Assume that Assumptions 1 and 2 hold. Consider the MASs (8) and (9) with the PTLBC control protocol (19). If the following conditions can be satisfied, whereυ1= λmax(Ξ)λmax(Q),υ2=λmax(Ξ)λmin(Q), and definition Δ5=λmax(Q)γi2. Then the lag bipartite consensus errors x―i(t) and v―i(t)converge to 0 within arbitrarily prescribed time t0+3T, i.e., using the proposed control protocol (19), the PTLBC of the MASs in (8) and (9) can realized. Proof. Let δ=[x~T,v~T]T. It can choose the Lyapunov function below, where Here, Q and Ξ are explained in Lemma 3. It can get that Ξ is positive define based on Lemma 2. Using the first inequality of (25), it gets V2≥0. Then Based on Assumption 2, Lemma 3 and 1Ψ3(t)≤3Tρ, one gets From the trigger condition (18), one gets where Applying Lemma 3, it gets The V˙2 can be simplified as follows Combining (28), (29), (30) and (32), it gets Let Z=[@cc@(Δ1+Δ3)Q00(Δ2+Δ4)Q], then and Then, by Lemma 5, the system is prescribed-time stable. The following solution can be obtained That is, the lag bipartite consensus error x―i(t) and v―i(t)converges to zero within T3. Then, the PTLBC of the MASs and can be achieved. Theorem 3. Considering the MASs (8) and (9) with the PTLBC control protocol, the Zeno behaviour can be excluded. Proof. Taking the derivative of e(t), it has Let Δ=max{(k1Ψ˙(t)+k2cx),(k1Ψ(t)+k2cv)}, and then According to (34), it gets Then, according to (26), it obtains Hence Obviously And then Considering ei(tki)=0, it obtains At trigger instant tk+1i, it follows According to (18), at trigger instant tk+1i combining with (42) and (43), it follows Next, using reduction to absurdity, it will be proved that the trigger interval tk+1i−tki≠0. Assume tk+1i−tki=0, it can be deduced from that 0<γi≤0, which leads to a contradiction. Hence, the assumption does not hold, that is, the proposed event-triggered mechanism excludes Zeno behaviour. 4. Numerical results The simulation results of nonlinear MASs (8) and (9) under the PTLBC control protocol (19) are given in the section. In S1 Fig, the nonlinear MASs with one leader and six followers is presented. The solid line indicates cooperation relationships, and the dashed line indicates the competitive relationships of the followers. The followers are partitioned into two subsets 𝒱1∈{v1,v2,v3} and 𝒱2∈{v4,v5,v6}, which means that θ=diag(1,1,1,−1,−1,−1). The Laplacian matrix L is below. Obviously, B=diag(1,\hspace{0.5em}1,\hspace{0.5em}1,\hspace{0.5em}0,\hspace{0.5em}0,\hspace{0.5em}0). For the leader, the control input is expressed as u0=0.1*\hspace{0.5em}sin(t), and the nonlinear part is expressed as g(t,x0(t),v0(t))=0.2v0(t)sin(x0(t)). The nonlinear parts of the followers are expressed as g(t,xi(t),vi(t))=0.2vi(t)sin(xi(t)),i=1,2,3,4,5,6. Obviously, we can verify that Assumption 2 is satisfied with cx=0.03 and cv=0.2. Set t0=0s, T=2s and τ=1s. The conditions (25) of Theorem 2 are satisfied when we choose k1=7, k2=6.23. The initial states values are given by x0(0)=1, v0(0)=1, x(0)=[−5−47825]T and v(0)=[−3.5−0.52.51.551]T respectively. Setting the parametersα=0.65, γi=[0.250.250.250.250.250.25], ρ=1 and b=0.25 in the event-triggering function, the function is given as follows The initial values ϑxi and ϑvi of the PTDO are set to [4,0,5,−5,−1,−4] and [5,−5,3,3,4,−5], respectively. S2 Fig shows that ϑ―xi converges to 0 within the arbitrary prescribed time 2s, and ϑ―vi converges to 0 within the arbitrary prescribed time 4s, with the lag time 1s. This demonstrates that the PTDO is effective. S3 Fig A and S3 Fig B provide the detailed variation curves of the position and velocity for all agents. It indicates that LBC is realized within the prescribed time 6s, with the lag time 1s. S4 Fig presents the event intervals for follower, which confirms that Zeno behaviour does not occur. 5. Conclusion The paper has researched the PTLBC control problem of nonlinear MASs. The PTDO has been devised for followers to acquire the states of the leader, and the event-triggered mechanism has been devised to save communication consumption. Via the PTDO and the event-triggered mechanism, the PTLBC control protocol has been designed. Utilizing Lyapunov stability analysis method, it has been rigorously proven that the nonlinear MASs (8) and (9) can achieve PTLBC. Furthermore, the Zeno behaviour of the controllers has been excluded. And then, the theoretical results were verified through the simulation example. We will further explore the problem subject to cyber attacks in our future work. Supporting information The connected topology of the nonlinear MASs. (TIF) The observer errors of followers. (TIF) The states variation curves of all agents. (TIF) Triggering instant sequences of followers. (TIF) Data for Numerical results. (ZIP) 24 Mar 2026 -->-->PONE-D-26-08045-->-->Observer-based prescribed-time lag bipartite consensus of nonlinear multi-agent systems under event-triggered mechanism-->-->PLOS One Dear Dr. Li, Thank you for submitting your manuscript to PLOS ONE. After careful consideration, we feel that it has merit but does not fully meet PLOS ONE’s publication criteria as it currently stands. Therefore, we invite you to submit a revised version of the manuscript that addresses the points raised during the review process. Please submit your revised manuscript by May 08 2026 11:59PM. If you will need more time than this to complete your revisions, please reply to this message or contact the journal office at plosone@plos.org. When you're ready to submit your revision, log on to https://www.editorialmanager.com/pone/ and select the 'Submissions Needing Revision' folder to locate your manuscript file. Please include the following items when submitting your revised manuscript:--> A letter that responds to each point raised by the academic editor and reviewer(s). You should upload this letter as a separate file labeled 'Response to Reviewers'.A marked-up copy of your manuscript that highlights changes made to the original version. You should upload this as a separate file labeled 'Revised Manuscript with Track Changes'.An unmarked version of your revised paper without tracked changes. You should upload this as a separate file labeled 'Manuscript'. A letter that responds to each point raised by the academic editor and reviewer(s). You should upload this letter as a separate file labeled 'Response to Reviewers'. A letter that responds to each point raised by the academic editor and reviewer(s). You should upload this letter as a separate file labeled 'Response to Reviewers'. A marked-up copy of your manuscript that highlights changes made to the original version. You should upload this as a separate file labeled 'Revised Manuscript with Track Changes'. A marked-up copy of your manuscript that highlights changes made to the original version. You should upload this as a separate file labeled 'Revised Manuscript with Track Changes'. An unmarked version of your revised paper without tracked changes. You should upload this as a separate file labeled 'Manuscript'. An unmarked version of your revised paper without tracked changes. You should upload this as a separate file labeled 'Manuscript'. If you would like to make changes to your financial disclosure, please include your updated statement in your cover letter. Guidelines for resubmitting your figure files are available below the reviewer comments at the end of this letter. If applicable, we recommend that you deposit your laboratory protocols in protocols.io to enhance the reproducibility of your results. Protocols.io assigns your protocol its own identifier (DOI) so that it can be cited independently in the future. For instructions see: https://journals.plos.org/plosone/s/submission-guidelines#loc-laboratory-protocols. Additionally, PLOS ONE offers an option for publishing peer-reviewed Lab Protocol articles, which describe protocols hosted on protocols.io. Read more information on sharing protocols at https://plos.org/protocols?utm_medium=editorial-email&utm_source=authorletters&utm_campaign=protocols. As the corresponding author, your ORCID iD is verified in the submission system and will appear in the published article. PLOS supports the use of ORCID, and we encourage all coauthors to register for an ORCID iD and use it as well. Please encourage your coauthors to verify their ORCID iD within the submission system before final acceptance, as unverified ORCID iDs will not appear in the published article. Only the individual author can complete the verification step; PLOS staff cannot verify ORCID iDs on behalf of authors. We look forward to receiving your revised manuscript. Kind regards, Hongru Ren Academic Editor PLOS One Journal Requirements: -->1. When submitting your revision, we need you to address these additional requirements.-->--> -->-->Please ensure that your manuscript meets PLOS ONE's style requirements, including those for file naming. The PLOS ONE style templates can be found at -->-->https://journals.plos.org/plosone/s/file?id=wjVg/PLOSOne_formatting_sample_main_body.pdf and -->-->https://journals.plos.org/plosone/s/file?id=ba62/PLOSOne_formatting_sample_title_authors_affiliations.pdf-->--> -->-->2. Please note that PLOS One has specific guidelines on code sharing for submissions in which author-generated code underpins the findings in the manuscript. In these cases, we expect all author-generated code to be made available without restrictions upon publication of the work. Please review our guidelines at https://journals.plos.org/plosone/s/materials-and-software-sharing#loc-sharing-code and ensure that your code is shared in a way that follows best practice and facilitates reproducibility and reuse.-->--> -->-->3. Thank you for stating the following financial disclosure: -->-->Tao Li received the funding of the National Natural Science Foundation of China under Grant number 62473135, Xiaowen Zhao received the funding of the National Natural Science Foundation of China under Grant number 62173121, Le Yan received the Natural Science Foundation of Hubei Province of China under Grant number 2024AFB812. -->--> -->-->Please state what role the funders took in the study. If the funders had no role, please state: "The funders had no role in study design, data collection and analysis, decision to publish, or preparation of the manuscript." -->-->If this statement is not correct you must amend it as needed. -->-->Please include this amended Role of Funder statement in your cover letter; we will change the online submission form on your behalf.-->--> -->-->4. Thank you for stating the following in the Acknowledgments Section of your manuscript: -->-->This work is supported by the National Natural Science Foundation of China under Grants 62473135 and 62173121, in part by the Natural Science Foundation of Hubei Province of China under Grant 2024AFB812.-->--> -->-->We note that you have provided funding information that is not currently declared in your Funding Statement. However, funding information should not appear in the Acknowledgments section or other areas of your manuscript. We will only publish funding information present in the Funding Statement section of the online submission form. -->-->Please remove any funding-related text from the manuscript and let us know how you would like to update your Funding Statement. Currently, your Funding Statement reads as follows: -->-->Tao Li received the funding of the National Natural Science Foundation of China under Grant number 62473135, Xiaowen Zhao received the funding of the National Natural Science Foundation of China under Grant number 62173121, Le Yan received the Natural Science Foundation of Hubei Province of China under Grant number 2024AFB812. -->--> -->-->Please include your amended statements within your cover letter; we will change the online submission form on your behalf.-->--> -->-->5. We note that your Data Availability Statement is currently as follows: All relevant data are within the manuscript and its Supporting Information files.-->--> -->-->Please confirm at this time whether or not your submission contains all raw data required to replicate the results of your study. Authors must share the “minimal data set” for their submission. PLOS defines the minimal data set to consist of the data required to replicate all study findings reported in the article, as well as related metadata and methods (https://journals.plos.org/plosone/s/data-availability#loc-minimal-data-set-definition).-->--> -->-->For example, authors should submit the following data:-->--> -->-->- The values behind the means, standard deviations and other measures reported;-->-->- The values used to build graphs;-->-->- The points extracted from images for analysis.-->--> -->-->Authors do not need to submit their entire data set if only a portion of the data was used in the reported study.-->--> -->-->If your submission does not contain these data, please either upload them as Supporting Information files or deposit them to a stable, public repository and provide us with the relevant URLs, DOIs, or accession numbers. For a list of recommended repositories, please see https://journals.plos.org/plosone/s/recommended-repositories.-->--> -->-->If there are ethical or legal restrictions on sharing a de-identified data set, please explain them in detail (e.g., data contain potentially sensitive information, data are owned by a third-party organization, etc.) and who has imposed them (e.g., an ethics committee). Please also provide contact information for a data access committee, ethics committee, or other institutional body to which data requests may be sent. If data are owned by a third party, please indicate how others may request data access.-->--> -->-->6. Please upload a new copy of Figures 2, 3, and 4, as the detail is not clear. Please follow the link for more information: https://journals.plos.org/plosone/s/figures-->--> -->-->7. If the reviewer comments include a recommendation to cite specific previously published works, please review and evaluate these publications to determine whether they are relevant and should be cited. There is no requirement to cite these works unless the editor has indicated otherwise. Additional Editor Comments: In light of the reviewers’ comments, the manuscript is considered to have potential for publication, provided that appropriate and necessary revisions are made. The authors are kindly requested to carefully address these comments and further improve the manuscript accordingly. -->--> -->-->[Note: HTML markup is below. Please do not edit.] Reviewers' comments: Reviewer's Responses to Questions--> -->Comments to the Author 1. Is the manuscript technically sound, and do the data support the conclusions? The manuscript must describe a technically sound piece of scientific research with data that supports the conclusions. Experiments must have been conducted rigorously, with appropriate controls, replication, and sample sizes. The conclusions must be drawn appropriately based on the data presented.--> Reviewer #1: Yes Reviewer #2: Yes ********** -->2. Has the statistical analysis been performed appropriately and rigorously?--> Reviewer #1: Yes Reviewer #2: Yes ********** -->3. Have the authors made all data underlying the findings in their manuscript fully available? The PLOS Data policy requires authors to make all data underlying the findings described in their manuscript fully available without restriction, with rare exception (please refer to the Data Availability Statement in the manuscript PDF file). The data should be provided as part of the manuscript or its supporting information, or deposited to a public repository. For example, in addition to summary statistics, the data points behind means, medians and variance measures should be available. If there are restrictions on publicly sharing data—e.g. participant privacy or use of data from a third party—those must be specified.--> Reviewer #1: No Reviewer #2: No ********** -->4. Is the manuscript presented in an intelligible fashion and written in standard English? PLOS ONE does not copyedit accepted manuscripts, so the language in submitted articles must be clear, correct, and unambiguous. Any typographical or grammatical errors should be corrected at revision, so please note any specific errors here.--> Reviewer #1: Yes Reviewer #2: Yes ********** -->5. Review Comments to the Author Please use the space provided to explain your answers to the questions above. You may also include additional comments for the author, including concerns about dual publication, research ethics, or publication ethics. (Please upload your review as an attachment if it exceeds 20,000 characters)--> Reviewer #1: This manuscript studies the observer-based prescribed-time lag bipartite consensus problem for nonlinear multi-agent systems under an event-triggered mechanism. The topic is relevant, and the integration of prescribed-time observer design, event-triggered communication, and lag bipartite consensus is potentially interesting. However, the following comments must be considered: 1. The notation system and several basic definitions need substantial revision. 2. Theorem 2 invokes Assumptions 1, 2, and 3, but Assumption 3 is not explicitly stated in the provided preliminaries. 3. The prescribed-time design and the time parameters T, T_1, T_2, and T_3 should be clarified much more carefully. 4. The main proofs, especially for Theorems 1 and 2, rely on several matrix inequalities and positive-definiteness claims, but the derivations are presented too briefly. In particular, the manuscript needs to justify more explicitly why the chosen Lyapunov functions are positive definite under the proposed parameter conditions, and how the bounds are transformed step by step. 5. The Introduction would benefit from citing and discussing several references relevant to the research methodology, which could further enrich the background on nonlinear control and event-triggered control, such as 10.1016/j.automatica.2024.111511, 10.1016/j.automatica.2022.110792, and 10.1109/TIE.2026.3654623. Reviewer #2: This paper aims to address the prescribed-time lag bipartite consensus control problem for nonlinear multi-agent systems. Generally, this is a well written and organized article with interesting theoretical results proposed. However, some concerns have to be addressed for better qualification: The contribution should be stated by comparing with the existing results, therefore, the novelty should be further improved and highlighted. The reasonability and references of assumptions should be given. Some latest results about finite-time control should be introduced such as tuning function-based light computational adaptive fixed-time control for overhead cranes with multiple uncertainties, security-driven adaptive iterative learning formation control for multiagent systems etc., to make the review complete. Fig. 4 is unclear, please revise it. Some comparison results should be shown to explain the novelty of the proposed method. The future work should be added to the conclusion. The linguistic quality or grammar problems need improvement, such as "\beta are the observer gains" etc. The authors should pay attention to these problems. ********** -->6. PLOS authors have the option to publish the peer review history of their article (what does this mean?). If published, this will include your full peer review and any attached files. If you choose “no”, your identity will remain anonymous but your review may still be made public. Do you want your identity to be public for this peer review? For information about this choice, including consent withdrawal, please see our Privacy Policy.--> Reviewer #1: No Reviewer #2: No ********** [NOTE: If reviewer comments were submitted as an attachment file, they will be attached to this email and accessible via the submission site. Please log into your account, locate the manuscript record, and check for the action link "View Attachments". If this link does not appear, there are no attachment files.] To ensure your figures meet our technical requirements, please review our figure guidelines: https://journals.plos.org/plosone/s/figures You may also use PLOS’s free figure tool, NAAS, to help you prepare publication quality figures: https://journals.plos.org/plosone/s/figures#loc-tools-for-figure-preparation. NAAS will assess whether your figures meet our technical requirements by comparing each figure against our figure specifications. --> 23 Apr 2026 The authors wish to thank the Editor and the anonymous reviewers very much for their valuable comments and suggestions, which leads to significant improvement of the quality and presentation of the manuscript. In the attachment "Response to Reviewers.docx" , we have given the detailed explanation how the editor’s and reviewer' comments have been taken into account in the revision. Submitted filename: Response to Reviewers.docx 6 May 2026 Observer-based prescribed-time lag bipartite consensus of nonlinear multi-agent systems under event-triggered mechanism PONE-D-26-08045R1 Dear Dr. Li, We’re pleased to inform you that your manuscript has been judged scientifically suitable for publication and will be formally accepted for publication once it meets all outstanding technical requirements. Within one week, you’ll receive an e-mail detailing the required amendments. When these have been addressed, you’ll receive a formal acceptance letter and your manuscript will be scheduled for publication. An invoice will be generated when your article is formally accepted. Please note, if your institution has a publishing partnership with PLOS and your article meets the relevant criteria, all or part of your publication costs will be covered. Please make sure your user information is up-to-date by logging into Editorial Manager at Editorial Manager® and clicking the ‘Update My Information' link at the top of the page. For questions related to billing, please contact billing support. If your institution or institutions have a press office, please notify them about your upcoming paper to help maximize its impact. If they’ll be preparing press materials, please inform our press team as soon as possible -- no later than 48 hours after receiving the formal acceptance. Your manuscript will remain under strict press embargo until 2 pm Eastern Time on the date of publication. For more information, please contact onepress@plos.org. Kind regards, Hongru Ren Academic Editor PLOS One Additional Editor Comments (optional): The revised manuscript has been re-reviewed by multiple reviewers and has received favorable evaluations and unanimous approval from all of them. After carefully assessing the reviewers’ comments and the overall academic quality of the manuscript, I fully agree with the reviewers’ judgments and recommendations. Reviewers' comments: Reviewer's Responses to Questions -->Comments to the Author 1. If the authors have adequately addressed your comments raised in a previous round of review and you feel that this manuscript is now acceptable for publication, you may indicate that here to bypass the “Comments to the Author” section, enter your conflict of interest statement in the “Confidential to Editor” section, and submit your "Accept" recommendation.--> Reviewer #1: All comments have been addressed Reviewer #2: All comments have been addressed ********** -->2. Is the manuscript technically sound, and do the data support the conclusions? The manuscript must describe a technically sound piece of scientific research with data that supports the conclusions. Experiments must have been conducted rigorously, with appropriate controls, replication, and sample sizes. The conclusions must be drawn appropriately based on the data presented. --> Reviewer #1: Yes Reviewer #2: Yes ********** -->3. Has the statistical analysis been performed appropriately and rigorously? --> Reviewer #1: Yes Reviewer #2: Yes ********** -->4. Have the authors made all data underlying the findings in their manuscript fully available? The PLOS Data policy requires authors to make all data underlying the findings described in their manuscript fully available without restriction, with rare exception (please refer to the Data Availability Statement in the manuscript PDF file). The data should be provided as part of the manuscript or its supporting information, or deposited to a public repository. For example, in addition to summary statistics, the data points behind means, medians and variance measures should be available. If there are restrictions on publicly sharing data—e.g. participant privacy or use of data from a third party—those must be specified.--> Reviewer #1: Yes Reviewer #2: Yes ********** -->5. Is the manuscript presented in an intelligible fashion and written in standard English? PLOS ONE does not copyedit accepted manuscripts, so the language in submitted articles must be clear, correct, and unambiguous. Any typographical or grammatical errors should be corrected at revision, so please note any specific errors here.--> Reviewer #1: Yes Reviewer #2: Yes ********** -->6. Review Comments to the Author Please use the space provided to explain your answers to the questions above. You may also include additional comments for the author, including concerns about dual publication, research ethics, or publication ethics. (Please upload your review as an attachment if it exceeds 20,000 characters)--> Reviewer #1: The authors have addressed all my concerns. I think this paper can be accept now. Good luck to the authors. Reviewer #2: This paper has been revised well. I have no further comments. As a result, I suggest that it can be accepted. ********** -->7. PLOS authors have the option to publish the peer review history of their article (what does this mean?). If published, this will include your full peer review and any attached files. If you choose “no”, your identity will remain anonymous but your review may still be made public. Do you want your identity to be public for this peer review? For information about this choice, including consent withdrawal, please see our Privacy Policy.--> Reviewer #1: No Reviewer #2: No **********