Bio-inspired green combustion synthesis of CaTiO3 nanoparticles via Aloe vera extract for synergetic photocatalytic degradation of Malachite green and electrochemical sensing of glyphosate Authors: Syed Khasim, Taymour A. Hamdalla, Nawal Alghamdi, Suhair A. Bani-Atta, Mansour Alatawi, Chellasamy Panneerselvam Published: 2026 ABSTRACT A green combustion route was developed using Aloe vera extract for the synthesis of highly crystalline Calcium Titanate (CaTiO3) (CTO) nanoparticles (~ 30 nm). The optimized CaTiO3 NPs exhibits a direct optical band gap of 3.12 eV and abundant surface oxygen vacancies, enhancing charge separation and light absorption. As a photocatalyst, the material achieved a remarkable degradation efficiency of 90.44% for Malachite green (MG) dye under UV irradiation and 57.88% under sunlight within 120 min, following pseudo-first-order kinetics. Scavenger studies confirmed that photogenerated holes (h+) and hydroxyl radicals (·OH) play dominant roles in the degradation process. Furthermore, the Aloe vera–derived CaTiO3 demonstrated superior electrochemical activity toward Glyphosate detection, showing rapid amperometric response, low charge-transfer resistance, and excellent linearity (R2 > 0.96) across 1–6 µM concentration with LOD 0.38 µM and sensitivity ~ 0.25 µA µM–1. These results demonstrate the potential of Aloe vera–assisted CaTiO3 as a sustainable multifunctional nanomaterial that integrates environmental remediation and agrochemical sensing, offering a scalable and eco-friendly platform for next-generation photocatalysts and electrochemical sensors.Supplementary InformationThe online version contains supplementary material available at 10.1186/s11671-026-04641-3. Introduction Water pollution caused by industrial dyes and agricultural chemicals offers a serious threat to environmental and human health. Among these pollutants, synthetic dyes such as malachite green (MG) and herbicides like glyphosate are of particular concern due to their toxicity, persistence, and widespread use [1, 2]. The development of multifunctional materials capable of simultaneously addressing dye degradation and chemical sensing is therefore of significant interest. In the combustion synthesis of metal oxide nanoparticles, the choice of fuel plays a critical role in determining the structural, morphological, and functional properties of the final product [3, 4]. Traditional fuels such as urea, glycine, and citric acid have been widely used due to their ability to act as reducing agents and generate high combustion temperatures. However, these fuels often release toxic gases and involve non-renewable components. The sustainability of the Aloe vera-assisted combustion synthesis was evaluated by comparing basic metrics such as energy input, gas evolution, toxicity, and waste generation with conventional fuels including urea, glycine, and citric acid [5, 6]. Conventional fuels are typically nitrogen-rich and undergo highly exothermic combustion, releasing toxic gases such as NOx and NH3, which increase environmental and health risks. In contrast, Aloe vera extract, being a renewable biomass-derived fuel, promotes a relatively mild and controlled combustion process with reduced energy input and predominantly releases benign gases such as CO2 and water vapor. Furthermore, the use of Aloe vera eliminates the need for additional complexing agents or solvents, thereby reducing chemical consumption and lowering the effective E-factor. These features collectively demonstrate that Aloe vera–assisted synthesis offers clear sustainability advantages over conventional combustion fuels, supporting its suitability for green and environmentally benign nanoparticle synthesis. These biomolecules not only serve as effective combustion agents but also aid in controlling particle growth, enhancing crystallinity, and introducing beneficial surface defects such as oxygen vacancies [7]. Compared to synthetic fuels, Aloe vera promotes a more uniform combustion reaction, resulting in better particle dispersion and functional properties, while also aligning with green chemistry principles. Thus, the use of Aloe vera gel not only reduces environmental impact but also enhances the quality and applicability of nanoparticles for photocatalytic and sensing applications. Nanomaterials play a crucial role in treatment of waste water due to their unique physical, chemical, and electronic properties that differ significantly from their bulk counterparts [8, 9]. These characteristics make them highly effective in processes like water splitting, pollutant degradation, and energy conversion. Preparation of these nanomaterials by the green combustion method is an eco-friendly approach for synthesizing nanoparticles like calcium titanate (CaTiO3), it uses naturally derived fuels as Aloe vera gel and minimizes harmful chemical effects. Calcium Titanate (CaTiO3) nanoparticles belong to the category of advanced material with a wide range of applications due to their unique physical and chemical properties. Its size range of 1–100 nm having perovskite- structure, with pale yellow color in powdered form. Calcium Titanate (CaTiO3) nanoparticles are highly stable under normal conditions [10–12]. Tunable bandgap from (~ 3.0–3.5 eV), making it suitable for enabling and optimizing photocatalyst for desired light absorption and improving efficiency. There are many conventional analytical techniques used to treat the polluted water such as sedimentation, filtration, chlorination, ion exchange method and reverse osmosis among them photocatalytic degradation offers advantages such as strong oxidation power, no secondary pollution, benign reaction conditions and low cost. This approach shows great promise in the field of dye degradation [13–15]. Water and soil pollution is not only caused by the industrial dyes it also from the agricultural pesticides like glyphosate [16, 17]. The glyphosate is used as herbicide weed remover in crops. The detection of these toxic chemicals is very crucial due to the fact that it is easily soluble in water. Several techniques such as High-performance liquid chromatography (HPLC), Gas chromatography (GC), Mass spectrometry (MS), Colorimetric methods and Raman spectroscopy have been used for the sensing and quantification of glyphosate [18–20]. These spectroscopic techniques are expensive and require high-precision instruments that rely on complicated procedures with trained personal, time consuming and challenges due to cross-reactivity of certain interfering compounds. Among these reported methods, development of electrochemical sensors has received wide-ranging interest due to their noninvasive and nondestructive sensing ability, less quantity of sample requirement, and highly portable detection analysis [21]. In spite of many advantages of electrochemical sensors over other methods, however, there are challenges to overcome some issues such as low limit of detection, selectivity, repeatability, stability, and low cost. In this work, CaTiO3 nanoparticles were prepared by green solution combustion method using Aloe vera as a fuel and were characterized by XRD, FTIR, DRS and SEM. The dual application of CaTiO3 nanoparticles were explored. The photocatalytic activity by illuminating UV radiation and sun light to investigate the photodegradation of water-soluble Malachite green under normal temperature& pressure. In addition, we report the electrochemical sensing application of the glyphosate. There are few reports exploring the Photocatalytical degradation of organic dyes using CaTiO3 nanoparticles in the past. But, the Aloe vera assisted synthesis of CaTiO3 nanoparticles as a dual platform towards photocatalytic degradation of MB dye and electrochemical sensing of Glyphosate were never reported in the past. The Photocatalytic and Glyphosate sensing performance of CaTiO3 NPs synthesized in the present study using Aloe vera as a bio fuel is compared with similar and other materials, and its novelty as a multifunctional material is highlighted in comparative tables (Table S2–S5) of supplementary information. This work for the first time reports the integration of multifunctional features of CaTiO3 nanoparticles synthesized via Aloe vera extract as a fuel, that could open new technological avenues for environmental remediations. Experimental Chemicals used in preparation of CTO NPs CaTiO3 nanoparticles (CTO NPs) were synthesized through solution combustion method using Aloe vera as a fuel. The chemicals used in this process included N-butyl titanate, nitric acid (HNO3), and calcium nitrate [Ca(NO3)2], procured from NICE Chemicals (P) Ltd. Synthesis of CTO NPs using Aloe vera as a fuel The titanium nitrate was first prepared using, hydrolyzing N-butyl titanate by adding minimum quantity of water in a petri dish, leading to the formation of titanyl hydroxide. Further addition of HNO3 resulted in the formation of titanyl nitrate. The previous steps were followed to prepare titanyl nitrate, and is mixed with stoichiometric amounts of Ca(NO3)2 and added 20 ml of an Aloe vera extract solution with deionized water and the mixture was thoroughly mixed using a magnetic stirrer for 30 min at room temperature. The resulting stock mixture was then subjected to combustion in a muffle furnace at 500 ± 10 °C. Finally, the obtained product was calcined at 700 °C for 2 h and characterized using specific spectral techniques for structural confirmation. The steps involved in the synthesis of CTO NPs are illustrated in the flow diagram (Fig. 1). Fig. 1Flowchart representing the synthesis process for CTO NPs Flowchart representing the synthesis process for CTO NPs Materials characterization Crystal structure and phase formation were investigated using Shimadzu Powder X-Ray diffractometer (PXRD) in 2θ range 20–70 with Cu Kα radiation. The surface morphology of synthesized nanoparticles was analyzed through scanning electron microscope (SEM) (JOEL JSM 840 A) at an accelerating voltage of 20 kV using a tungsten filament. The chemical features and bond formation were studied through FT-IR in the range 4000–400 cm− 1 using Spectrum-1000 (Perkin Elmer) spectrophotometer. The UV–Visible absorption spectra of the nanoparticles was recorded using UV–Visible Spectrophotometer (Shimadzu UV 2600 UV–Visible). In-depth analysis of morphological features was investigated through Transmission Electron Microscopy (TEM) (Hitachi H-8100) (at an accelerating voltage of 200 kV, LaB6 filament). The Electrochemical performances were carried out by CHI608E potentiostat using 1 M KOH at various scan rates. Photocatalytic measurements of organic dyes by CTO NPs Under UV-light irradiation Photocatalytic activity of CTO nanoparticles was examined by the degradation of Malachite green (MG) dye illuminated under UV light of mercury vapor lamp (UV light with 125 W). Firstly, the prepared 20 ppm of MG dye solution, using this 20 ppm standard MG dye solution in a glass container and add 0.02 gm of CTO nanoparticle as catalyst to prepare dye solution. Then, the prepared dye solution was placed under UV light irradiation with a magnetic stirrer for homogenously to activate the degradation process. For every regular interval of 15 min constitutively 5 ml of dye solution is reverted up to the 120 min. The reverted dye solution is subjected to centrifugation for 15 mints, followed by the examination using UV visible absorbance spectrometry [22, 23]. Under sun light irradiation The procedure of dye degradation under sun light irradiation is as follows. The experiment is started in May month at the time of 12 pm because near the equator, the sun’s rays are more direct, resulting in higher intensity. Firstly, the 20 ppm of standard MG dye solution is taken in glass container and added 0.02 gm Aloe vera made CTO nanoparticle as catalyst to the dye solution and is placed in magnetic stirrer for homogenously activating the degradation process. For every regular interval of 15 min constitutively 5 ml of dye solution is reverted up to the 120 min. Preparation of electrode for electrochemical studies For cyclic voltammetry (CV) studies, the working electrodes were fabricated by mixing 0.025 g of CTO NPs with 0.475 g of graphite powder. To ensure proper binding of the materials, 3 drops of silicon oil were added to the mixture. The components were then thoroughly hand-mixed using a mortar and pestle for approximately 20 min, resulting in a homogeneous and well-blended electrode paste suitable for electrochemical testing [24]. Results and discussion XRD investigation Fig. 2a: X-ray diffractogram of CTO NPs synthesized via combustion method b: W-H plot a: X-ray diffractogram of CTO NPs synthesized via combustion method b: W-H plot The X-ray diffraction (XRD) patterns of CTO NPs synthesized using Aloe vera as a fuel is shown in Fig. 2. The distinct diffraction peaks observed at 2θ = 12.76°, 32.91°, 49.74°, 58.34°, and 70.5° correspond to the (100)/(002), (112), (220), (204), and (224) crystal planes, respectively. These patterns align with the orthorhombic structure, which is consistent with standards JCPDS No. 88-0790, confirming the formation of CTO. The sharp and intense diffraction peaks indicate that the synthesized nanoparticles exhibit high crystallinity [25]. Further refinement in the diffraction peaks could be possible using Rietveld refinement technique, which is beyond the scope of this study and could be explored in articles explicitly focusing on in-depth analysis of structural features of this nano system. The average crystal size of the green-synthesized CTO nanoparticles was determined using Debye-Scherrer’s equation, where D represents the crystal size, and λ is the X-ray wavelength (0.154 nm) [26, 27]. The estimated average crystal size of the CTO nanoparticles was 30 nm confirming the nanocrystalline nature of the synthesized CTO. The estimated crystalline size shows in Table S1.1\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:D=\frac{0.9\lambda\:}{\beta\:cos\theta\:}$$\end{document} where λ is wavelength of X-rays, β represents Full width at half maximum (FWHM) of XRD peaks. Figure 2b represents the Williamson–Hall plot of βcosθ versus 4sinθ, used to analyze the contributions of crystallite size and lattice strain to peak broadening. The Williamson–Hall analysis was performed by plotting βcosθ as a function of 4sinθ to separate the contributions of crystallite size and lattice strain to peak broadening. The linear fit yielded a slope of 0.00321, corresponding to a lattice strain of \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:\:8.03\times\:{10}^{-4}$$\end{document}, indicating mild lattice distortion in the synthesized CTO nanoparticles. The small intercept value suggests that strain-induced broadening dominates over size-induced broadening. The moderate Pearson’s correlation coefficient (r = 0.72) and adjusted R2 value (0.36) indicate a reasonable linear fit, which is commonly observed in nanocrystalline materials. FT-IR analysis Fig. 3FT-IR spectra CTO NPs FT-IR spectra CTO NPs The Fourier transform infrared spectroscopy (FTIR) revels the functional groups present in Aloe vera assisted synthesis of CTO NPs and is represented in Fig. 3. The broad band curves show a characteristic peak in the region around 3669 cm−1 which is attributed to O–H stretching vibrations, which indicates the presence of hydroxyl groups. Peak at 1790 cm−1 correspond to C=O stretching vibrations, which could arise from post-calcination surface carbonation (surface absorbed atmospheric species), arising from the interaction of Ca-containing perovskite surfaces with ambient CO₂ during cooling and storage. The Peak at 1491 cm−1 is corresponding to C–H bending vibrations due to the interaction of carbon-based precursors during synthesis. When plant extracts (e.g. Aloe vera) are employed as a combustion fuel for the synthesis of CTO NPs, the trace C–O–Ti surface linkages that persists on the surface may result in the broadening of peaks at 1086 cm−1 due to overlapping of Ti–O stretching modes. In Peaks at 877 cm−1 is due to Ti–O Vibrations is attributed to Ti–O stretching vibrations of the CTO structure. This confirms the formation of the perovskite phase. The Aloe-vera fuel-based CTO contains additional organic signatures from plant-derived compounds and its hydroxyl content. The synthesized sample yield hydroxyl-rich surfaces [28–29]. Optical analysis Fig. 4The energy band gap of CTO NPs The energy band gap of CTO NPs The inset of Fig. 4 shows the diffuse reflection spectra of the synthesized (CTO) nanoparticles in the spectral range of 200–800 nm, prepared using Aloe vera extract as a fuel. Since the measurements were carried out in diffuse reflectance mode, the reflectance data were converted into an absorption coefficient using the Kubelka–Munk function, as given in Eq. (2). The optical band gap was estimated using the Tauc relation, as expressed in Eq. (3), The value of ‘n’ decides whether direct allowed transition (n = ½) or indirectly allowed transition (n = 2) for CTO nanoparticles. The Tauc relation for the energy band gap and the linear absorption coefficient (α) of a material, is given by Eq. 4. Accordingly, a plot of \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\left(F\left(R\right)h\vartheta\:\right)}^{2}$$\end{document} versus photon energy \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$(h\vartheta\:$$\end{document}) was constructed, and the linear region near the absorption edge was extrapolated to the energy axis. The obtained optical band gap value is shown in Fig. 4 and was found to be approximately 3.12 eV for the synthesized CTO nanoparticles. The slight narrowing of the band gap in Aloe vera derived CTO nanoparticles can be attributed to oxygen vacancies and surface defects introduced by the organic components present in the Aloe vera gel. These intrinsic defects enhance charge separation, thereby improving photocatalytic activity under UV-light irradiation. Furthermore, the presence of abundant surface-active sites contributes to enhanced catalytic performance, while the favorable structural and electronic properties of CTO nanoparticles also enable their application as efficient glyphosate sensors. The band gap values obtained for CTO NPs using various synthesis methods are summarized in Table S2, indicating the potential of CTO nanoparticles for a wide range of optoelectronic and photocatalytic applications [30] (Table 1).2\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\frac{K}{S}=\frac{{(1-R)}^{2}}{2R}$$\end{document} R is the diffused reflectance of nanoparticle and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:\frac{\mathrm{K}}{\mathrm{S}}$$\end{document} is function derived from reflectance, representing the ratio of absorption (K) to scattering (S) coefficients.3\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:{\left(F\left(R\right)h\upsilon\:\right)}^{n}=A\left(h\upsilon\:-{E}_{g}\right)$$\end{document}4\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:\alpha\:=\frac{{c}_{1}{\left(h\upsilon\:-{E}_{g}\right)}^{\frac{1}{2}}}{h\upsilon\:}$$\end{document} Table 1Summary of CTO NPs preparation methods and energy bang gap valuesMethod of preparationEnergy band gap in (eV)ReferencesHydrothermal method3.57 [10]Surfactant-aided Sol–gel method3.42–3.46 [31]Sol–gel method3.34 [32]Combustion method3.59 [33]Chemical route2.90–3.41 [32]Modified combustion method3.65 [34] Table 1Summary of CTO NPs preparation methods and energy bang gap valuesMethod of preparationEnergy band gap in (eV)ReferencesHydrothermal method3.57 [10]Surfactant-aided Sol–gel method3.42–3.46 [31]Sol–gel method3.34 [32]Combustion method3.59 [33]Chemical route2.90–3.41 [32]Modified combustion method3.65 [34] Summary of CTO NPs preparation methods and energy bang gap values Morphological analysis using SEM Fig. 5a SEM images and b EDX analysis of CTO nanoparticles a SEM images and b EDX analysis of CTO nanoparticles The Fig. 5a shows SEM images of CTO nanoparticle synthesized by using Aloe vera as fuel. The surface morphology shows denser and porous structures with particles significantly smaller and uniform. The Aloe vera gel used as fuel in combustion synthesis, contribute to promote gas evolution, leaving behind porous structures, this porous structure enhances the surface area, and the prepared CTO nanoparticle is beneficial for catalytic applications. The elemental composition of the prepared CTO nanoparticles is shown in Fig. 5b, which confirms the presence of pure compound. The inset of Fig. 5b gives atomic percentage and weight% of elements Ca, Ti and O that reveals purity of the elemental composition of CTO NPs [35, 36]. TEM analysis Fig. 6a and b are TEM images at different magnifications for CTO NPs, c HR-TEM d SAED pattern a and b are TEM images at different magnifications for CTO NPs, c HR-TEM d SAED pattern Figure 6a and b shows the TEM images of CTO NPs of medium magnification of 50 nm and low magnification of 200 nm. The TEM shows nanocrystalline domains aggregated into clusters of CTO NPs. The texture is porous, consistent with combustion synthesis and light contrast variation suggests non-uniform particle size formed from rapid nucleation and gas evolution during combustion. Figure 6c shows the High-Resolution TEM of 10 nm magnification. Figure 6d shows the observed fringe patterns, which represent the lattice planes of CTO NPs. These fringes can be measured to determine interplanar spacing (d-spacing), which can be matched to known planes of CTO NPs (e.g., (101), (112), etc.). Figure 6d SAED Pattern of 5 nm−1 confirms crystallinity at the nanoscale. The concentric bright rings correspond to different crystallographic planes of CTO NPs, indicating a polycrystalline structure. The spacing between rings can be indexed to known diffraction peaks of orthorhombic CTO NPs. A sharp and well-defined SAED pattern confirms high crystallinity of the sample [37, 38]. BET analysis Fig. 7Adsorption-desorption measurements showing BJH plot of CTO NPs Adsorption-desorption measurements showing BJH plot of CTO NPs The optimal porosity and high surface area (low particle size) are the two crucial things for the synthesized CTO NPs nanocomposite to be efficient catalyst. From Brunauer–Emmett–Teller (BET) study, N2 adsorption-desorption measurement carried out at 77 K (Fig. 7), the synthesized CTO NPs was found to exhibit type IV isotherm with a sharp increase of the adsorbed volume starting from P/P0 = 0.97. This confirms the presence of well-developed mesoporous nanostructured nature of CTO NPs. The shifting of the hysteresis loop to the higher as the relative pressure (p/po) approaching to 1 indicates the presence of the micro porous particles with size greater than 20 nm. Photocatalytic degradation studies Mechanism of photocatalytic degradation Fig. 8Photo-degradation mechanism Photo-degradation mechanism Synthesized CTO NPs have shown effective photocatalytic degradation of Malachite Green (MG) dye under both UV and sunlight exposure. As illustrated in the proposed mechanism in Fig. 8, oxygen (O2) and water (H2O) molecules readily adsorb onto the surface both outer and inner of the photocatalyst when irradiated [39]. Upon exposure to light with sufficient energy, electrons \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$ (e^{ - } ) $$\end{document} in the valence band are excited to the conduction band, leaving behind positively charged holes \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$ (h^{ + } ) $$\end{document} in the valence band. During the degradation process, MG dye molecules absorb the light energy and transition to an excited state, causing the breakdown of their chemical bonds. The CTO photocatalyst, under UV and solar irradiation, also release \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$ ~Ca^{{2 + }} $$\end{document} ions into the solution as part of the photocatalytic reaction. Meanwhile, the photo-excited electrons are captured by adsorbed oxygen molecules, forming superoxide radicals \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$ (O_{2} \cdot ^{ - } ) $$\end{document}, while the holes react with water molecules to produce hydroxyl radicals (·OH). These highly reactive species attack the MG dye molecules, leading to their breakdown into harmless end-products such as water (H2O), carbon dioxide (CO2), and mineral acids like nitrate \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$ (NO^{ - } _{3} ) $$\end{document}, nitrite\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$ (NO^{ - } _{2} ) $$\end{document}, and sulfate \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\ (SO^{{2 - }} _{4} ) $$\end{document}. Fig. 9a and b Absorbance spectra of Malachite green dye under UV and sunlight irradiation by using CTO NPs; c percentage degradation of Malachite green dye d kinematics study of Malachite green dye degradation a and b Absorbance spectra of Malachite green dye under UV and sunlight irradiation by using CTO NPs; c percentage degradation of Malachite green dye d kinematics study of Malachite green dye degradation The absorbance spectra of malachite green dye solution under irradiation of UV and sun light are shown in Fig. 9a and b respectively. The effectiveness of MG dye degradation under UV and sunlight was evaluated by measuring the initial concentration (C) and final concentration (C0) of the dye [40]. The percentage degradation was calculated using the formula:5\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$ \% ~Degradation = \frac{{c - c_{o} }}{{c_{0} }}{\mathrm{~}} { \times }100 $$\end{document} The photocatalytic activity of MG dye is influenced by parameters such as the catalyst load and dye concentration. Figure 9c illustrates the percentage degradation of MG dye using CTO nanoparticles as a catalyst under UV and sunlight irradiation the percentage degradation was 90.44% under UV light and 57.88% under sunlight. The photolysis condition under UV and sun light is 48.56% and 35.24%. The dye concentration used throughout the experiment was maintained at 20 mg/L. A pseudo-first order kinetics model was used to study the degradation kinetics of both MG dyes based on Equation [41]. 6\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:\mathrm{l}\mathrm{n}\frac{{c}_{o}}{c}=\mathrm{k}\mathrm{t}$$\end{document} where C0 is the initial concentration of the MG aqueous solution after achieving adsorption equilibrium with the photocatalyst, C is the concentration of MG aqueous solution after a given irradiation time in the system, and k is the apparent rate constant. Figure 9d shows a plot of C/C0 versus the time for the Aloe vera assisted CTO NPs as a photocatalyst irradiated under UV and sunlight. The plot of ln(C/C0) versus the reaction time is linear and the rate constant (k) equals the corresponding slope of the fitted line. The concentration of the substance decreases over time, in UV light irradiation consistently shows a steeper decline compared to sunlight irradiation, indicating a faster rate of degradation under UV light. The decrease in log C/C0 reflects a reduction in the substance’s concentration, with negative values howing progressive degradation. UV light is more effective than sunlight in catalyzing the degradation of the substance, due to its higher energy and ability to activate the photocatalyst more efficiently. Fig. 10Half-life of Malachite green dye under irradiation of UV light and sun light (a and b) by utilizing Aloe vera assisted CTO NPs Half-life of Malachite green dye under irradiation of UV light and sun light (a and b) by utilizing Aloe vera assisted CTO NPs The half-life is a crucial parameter for evaluating the efficiency practical applicability of photocatalytic processes. A shorter half-life indicates faster degradation of the target compound, which in turn reduces energy consumption by minimizing the required irradiation time. Figure 10a and b illustrates the half-life of Malachite Green dye under UV and sunlight irradiation, using Aloe vera-based CTO nanoparticles as the catalyst. The recorded half-life was 42.45 min under UV light and 66.29 min under sunlight, The degradation of Malachite Green followed pseudo-first-order kinetics under both UV and sunlight irradiation. A higher rate constant and shorter half-life were obtained under UV light compared to sunlight irradiation indicating faster degradation under UV illumination is given Table S3. indicating a comparatively better performance under UV light in the catalyst (Table 2). Table 2Compression of photocatalytic degradation kinetics of different dyes and method of synthesis of nanoparticlesMethod of synthesisLight sourcedyeDegradation (%)Rate constant, k (min−1)Half-life t1/2 (min)ReferencesGreen combustion methodUV lightMalachite green90.440.01928442.45Present workGreen combustion methodSunlightMalachite green57.880.00717366.29Present workThermal methodSun lightMethyl orange99.030.116– [42]Solid state methodUVMethylene blue96.60.00078– [43]Green synthesisSunlightMethylene blue73–76–– [44] Table 2Compression of photocatalytic degradation kinetics of different dyes and method of synthesis of nanoparticlesMethod of synthesisLight sourcedyeDegradation (%)Rate constant, k (min−1)Half-life t1/2 (min)ReferencesGreen combustion methodUV lightMalachite green90.440.01928442.45Present workGreen combustion methodSunlightMalachite green57.880.00717366.29Present workThermal methodSun lightMethyl orange99.030.116– [42]Solid state methodUVMethylene blue96.60.00078– [43]Green synthesisSunlightMethylene blue73–76–– [44] Compression of photocatalytic degradation kinetics of different dyes and method of synthesis of nanoparticles Fig. 11Different concentration of Malachite green dye degradation under irradiation of UV light and sun light (a and b) using CTO nanoparticles Different concentration of Malachite green dye degradation under irradiation of UV light and sun light (a and b) using CTO nanoparticles As shown in Fig. 11a and b the decolorization activity of Malachite Green (MG) dye was investigated by varying the dye concentration from 10 to 30 ppm, while maintaining a constant catalyst concentration of 20 mg. The rate of photodegradation increased over the course of 120 min under both UV light and sunlight irradiation. At 10 ppm, the lower dye concentration limits the number of molecules reaching the catalyst surface, resulting in a reduced reaction rate. In contrast, at 20 ppm, the dye concentration allows sufficient light penetration through the solution, ensuring efficient activation of the catalyst and maximizing the generation of reactive species. However, at higher concentrations (30 ppm), light penetration is delayed due to increased opacity, and self-quenching of the dye molecules becomes more pronounced, reducing the overall degradation efficiency. The very high percentage of decay observed at 20 ppm in both UV light and sunlight irradiation is attributed to an optimal balance between dye concentration, catalyst efficiency, light penetration, and reaction kinetics [45]. These findings emphasize the significance of optimizing dye concentration to achieve maximum photocatalytic performance. Fig. 12Stability studies of dye degradation under irradiation of UV light and sun light (a and b) by utilizing in CTO nanoparticle Stability studies of dye degradation under irradiation of UV light and sun light (a and b) by utilizing in CTO nanoparticle The synthesized sample was evaluated for reusability and photostability in degrading dye. Recyclability testing was conducted on Aloe vera made CTO sample using 20 ppm of MG dye over five cycles under both UV and sunlight exposure. The results, as depicted in Fig. 12a and b, demonstrated that the photocatalyst remained photostable, maintaining a consistent decolorization percentage over the first three cycles. However, a slight decline in decolorization efficiency was observed during the fourth and fifth cycles. This indicates that while the photocatalyst exhibits high photostability and reusability, prolonged use led to a minor reduction in performance, potentially due to catalyst degradation. Scavenger test Fig. 13Scavenger effect under irradiation of UV light in the presence of CTO nanoparticles Scavenger effect under irradiation of UV light in the presence of CTO nanoparticles Figure 13 depicts the scavenging tests performed to confirm the role of highly energetic free radicals in the photo decolorization of MG dye using CTO nanoparticles under UV light. Three distinct scavengers silver nitrate (AgNO3), ethanol, and ethylenediamine tetra acetic acid (EDTA) were used to analyze their impact on dye degradation. For the CTO nanoparticles synthesized with Aloe vera as a fuel, the photo decolorization efficiency of MG dye was 81.49%, 56.28%, and 41.59% in the presence of AgNO3, ethanol, and EDTA, respectively. In comparison, the degradation efficiency without any scavenger was 90.44%. These results indicate that EDTA (a hole scavenger) significantly reduces dye degradation, confirming that photogenerated h+ (holes) play a major role in the decomposition of MG dye. Additionally, AgNO3, in which scavenges e– (electrons), and ethanol, in which scavenges ·OH radicals, also affected the degradation efficiency but to a lesser extent. CTO nanoparticles exhibit superior photocatalytic performance due to their higher degradation efficiency and better hole-driven oxidation activity. This suggests that using Aloe vera as a fuel enhances the photocatalyst’s ability to generate and sustain reactive species, making it more effective in dye degradation under UV light. The present study is limited to a fixed catalyst dosage and neutral pH conditions. The influence of catalyst loading and solution pH on photocatalytic performance was not explored and remains a scope for future work. Electrochemical analysis Fig. 14a CV plot of Aloe vera assisted CTO NPs at different scan rates in 1 M KOH solution b relationship between the square root of the scan rate and the cathodic peak current (ip) c Nyquist plot d equivalent circuit a CV plot of Aloe vera assisted CTO NPs at different scan rates in 1 M KOH solution b relationship between the square root of the scan rate and the cathodic peak current (ip) c Nyquist plot d equivalent circuit The electrochemical characteristics of the Aloe vera derived CTO NPs electrode was investigated using cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) in a three-electrode system with 1 M KOH as the electrolyte. The CV measurements were performed at scan rates ranging from 0.01 to 0.05 V/s, as depicted in Fig. 14a. The CV response exhibited a well-defined voltammogram within the potential range of 0–1.2 V, indicating the redox activity of the CTO nanoparticles. The close potential difference between the cathodic and anodic peaks (~ 0.128 V) indicates a moderately fast electron transfer process, common in well-behaved redox systems. The recorded current response suggests efficient electron transfer, characteristic of an electrochemically active material [46]. The redox behavior of the electrode was assessed by analyzing the anodic (Epa) and cathodic (Epc) peak potentials. The minimal shift observed in these peaks with increasing scan rate confirms the diffusion-controlled nature of the redox process, where charge transport is primarily governed by ion diffusion at the electrode-electrolyte interface. The Randles-Sevcik equation was employed to evaluate the peak current (ip) and the peak potential separation (Ea, c), yielding a lower value of 0.139 V, which signifies improved reversibility of the redox process in the Aloe vera-derived CTO NPs. The plot of Fig. 14b establish a link between peak current and square root of potential scan rate with a regression coefficient value of 7.662 × 10− 4. The slope value of the obtained plot of peak current (Ip) vs. log scan rate (v) is close to one show which indicates the presence of diffusion-controlled processes [47]. Electrochemical impedance spectroscopy (EIS) is a technique for determining the interfacial properties of electrode surfaces. It provides vital insights into electrode material properties by measuring impedance fluctuations at the electrode-supporting electrolyte interface. EIS measurements were carried out in this work spanning a frequency range of 1 Hz to 1 MHz in open circuit conditions. The obtained data, presented in Fig. 14c and d as Nyquist plot and equivalent circuit, reveal that the CTO NPs have a reduced semicircular shape. This observation points to increased charge transfer efficiency. Incorporating CTO NPs into the supporting electrolyte reduced resistance, enhancing charge transfer performance. In the high-frequency regime of the Nyquist plot, the semicircle represents charge transport through the electrode-electrolyte interface, while the straight line represents electrode capacitance in the low-frequency zone. The diameter of the semicircle arc on the real axis can be determined from the amount of the Rct. For a reversible process, the Randles-Sevcik-Sevcikon utilizes the peak current7\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:\mathrm{i}\mathrm{p}=2.69\:\times\:{10}^{5}\:\times\:{\mathrm{n}}^{\frac{3}{2}}\:\times\:\mathrm{A}\:\times\:{\mathrm{D}}^{\frac{1}{2}}\times\:{\mathrm{C}}_{0}\times\:{\mathrm{v}}^{\frac{1}{2}}$$\end{document} The notations n, A, D, v, and Co are used to represent reaction parameters. These figures represent the quantity of electrons moved throughout the reaction [48]. Electrode size and scanning rate of the Aloe vera-derived CTO NPs.8\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:{\mathrm{c}}_{0}=\frac{\frac{{\uprho\:}}{\mathrm{M}}}{\mathrm{M}}$$\end{document} Fig. 15a Sensitivity measure of glyphosate, b comparison of glyphosate sensor and cv study, c cathodic peak current v/s glyphosate concentration a Sensitivity measure of glyphosate, b comparison of glyphosate sensor and cv study, c cathodic peak current v/s glyphosate concentration Figure 15a illustrates the sensor’s sensitivity to glyphosate in the concentration ranging from 1 to 6 µM. Figure 15b compares the cyclic voltammograms of the bare electrolyte and the electrolyte with glyphosate in the presence of a sensor. The bare electrolyte shows a cathodic peak at 0.337 V and an anodic peak at 0.4648 V, indicating standard redox behavior. In contrast, the glyphosate sensor exhibits a cathodic peak at 0.2476 V and two anodic peaks at 0.546 V and 0.7609 V. These shifts and the emergence of new peaks confirm the electroactive nature of glyphosate and its interaction with the electrode surface. The distinct redox responses highlight the sensor’s ability to detect glyphosate both qualitatively (via peak shifts) and quantitatively (via current response), supporting its potential for effective glyphosate monitoring. A calibration study was performed using glyphosate sensor CV, where the cathodic peak current (measured on the y-axis) was plotted against varying glyphosate concentrations (on the x-axis) shown in Fig. 15c. The experiment revealed two distinct cathodic peaks at 0.905 V and 0.250 V, indicating the presence of multiple electrochemical reduction processes related to glyphosate or its intermediates. Calibration curve at both reduction potentials, the cathodic peak current increased almost linearly with glyphosate concentration, confirming that the electrochemical response is directly related to the analyte concentrations. Statistical evaluation of adjusted R2 values of 0.967 (for 0.905 V) and 0.9654 (for 0.250 V) show excellent linearity, indicating that CV can be reliably used for quantifying glyphosate. The Residual Sum of Squares (RSS) was \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$ A = 1.558 \times 10^{{ - 7}} $$\end{document}and 4.3967 × 10⁻⁶, respectively both extremely low, further confirming the accuracy and precision of the calibration models. These results demonstrate that cyclic voltammetry can serve as a highly sensitive and reproducible method for detecting and quantifying glyphosate. The two cathodic peaks provide multiple detection windows, and the strong linear correlation with the concentration supports its potential for analytical applications [49]. Fig. 16a LSV glyphosate sensor, b peak current v/s glyphosate concentration a LSV glyphosate sensor, b peak current v/s glyphosate concentration Linear Sweep Voltammetry (LSV) of glyphosate sensor shown in Fig. 16a, the appearance of two anodic peaks at 0.546 V and 0.7609 V indicates that two distinct oxidation processes that are occurring during the voltage sweep. Each anodic peak represents a separate oxidation reaction, reflecting its complex electrochemical behavior. These peaks serve as valuable indicators for analyte identification and quantification, contributing to the sensor’s analytical capabilities [50]. The anodic peak current responses of the glyphosate sensor shown in Fig. 16b, obtained through linear sweep voltammetry, show a clear and consistent inverse linear relationship with glyphosate concentration across two distinct oxidation peaks. The first anodic peak (at ~ 0.546 V) and the second (at ~ 0.7609 V) exhibit high correlation coefficients (Pearson’s r = − 0.98796 and − 0.98678, respectively) and strong model fit (Adjusted R2 = 0.97009 and 0.96716), confirming the reliability and reproducibility of the sensor’s electrochemical response. The negative slopes observed in both calibration curves suggest that increasing glyphosate concentration leads to a measurable decrease in anodic peak current, due to interaction with the active sites of the sensor. The low residual sum of squares further supports the precision of the data. Overall, these results demonstrate that the sensor provides a sensitive, accurate, and stable electrochemical platform for glyphosate detection through its anodic peak current response. Fig. 17a Amperometric curve for determination of glyphosate, b glyphosate concentration v/s current (A) a Amperometric curve for determination of glyphosate, b glyphosate concentration v/s current (A) Figure 17a illustrates the amperometric current v/s (i–t) response of the prepared CTO NPs based carbon paste electrode for glyphosate detection over a potential range of 0–1.2 V. The electrode demonstrates a clear and immediate current response upon the initial addition of 1 µM glyphosate. With each successive addition of 1 µM glyphosate at 50-second intervals, the current increases sharply and stabilizes within just 3 s, indicating a rapid and sensitive electrochemical response. The steady-state current reaches approximately 0.00155 A, confirming the sensor’s high responsiveness to glyphosate oxidation. Figure 17b further supports these findings, showing a linear relationship between glyphosate concentration and current. As the glyphosate concentration increases, the current increases proportionally, with a strong correlation (R2 = 0.98). This linear trend establishes a direct quantitative link between analyte concentration and amperometric signal, validating the sensor’s effectiveness for accurate glyphosate measurement. Together, the rapid i–t response and the linear calibration curve confirm that the CTO NPs-modified electrode offers a fast, stable, and sensitive platform for glyphosate detection using amperometry [51]. Based on the linear detection range (1–6 µM), low detection limit (0.38 µM), slope values the sensitivity of the glyphosate sensor can be approximately calculated to be ~ 0.25 µA µM−1, indicating high analytical sensitivity. Sensing mechanism: The interaction of glyphosate with the CaTiO3 electrode surface occurs through strong surface complexation between the phosphonate groups of glyphosate and Ca2+/Ti4+ active sites, assisted by hydrogen bonding and oxygen vacancy-mediated electron transfer, resulting in enhanced electrochemical oxidation and sensing performance. Fig. 18a Selectivity of sensor b reproducibility of sensor c long term stability of the sensor a Selectivity of sensor b reproducibility of sensor c long term stability of the sensor Selectivity and reproducibility: When analyzing the performance of sensing devices, selectivity and reproducibility are essential considerations. In this study, we have confirmed the ability of the CTO nanoparticle electrode to selectively detect glyphosate in the presence of other interfering molecules with similar oxidation potentials and chemical properties, such as Vinegar, Botanical oil, Glufosinate, and Pelargonic acid. To assess selectivity, traditional amperometry was employed. At 0.8 V, the electrode exhibited a strong current response in the presence of 5 µM glyphosate. However, when potential interfering compounds Vinegar, Botanical oil, Glufosinate, and Pelargonic acid were introduced at a concentration of 0.1 µM, no significant changes in the response were observed as shown in Fig. 18a. A pronounced current increase was only recorded when the glyphosate concentration was raised to 5 µM, confirming that the CTO electrode is highly selective for glyphosate detection. To evaluate reproducibility, five independently prepared electrodes were tested using 5 µM glyphosate shown in Fig. 18b. The responses obtained showed a relative standard deviation (RSD) of just 1.3%, indicating that the electrodes fabricated in the same way demonstrated highly consistent performance. Further, the long-term stability of the sensor was tested in 5 µM concentration of Glyphosate and reported in Fig. 18c. The results clearly demonstrates that the CTO NPs modified electrode shows constant current signal over a period time indicating the sensor stability. Photoluminescence studies Fig. 19a Excitation spectra b emission spectra of CTO NPs (emission at 600 nm). c energy level diagram and d plotting log (I/x) versus log x CTO NPs a Excitation spectra b emission spectra of CTO NPs (emission at 600 nm). c energy level diagram and d plotting log (I/x) versus log x CTO NPs The excitation spectra (ranging from 330 to 500 nm) of CTO NPs, monitored at an emission wavelength of 600 nm and presented in Fig. 19a. The spectra consist of twelve excitation peaks and are assigned to the respective f–f transitions from 6H5/2 (ground state) to excited states such as 4P3/2 (331 nm), 4G5/2 (342 nm), 4D7/2,4H9/2 (331 nm), 4D3/2,4D5/2,4P5/2 (373 nm), 4F7/2,6P3/2 (401 nm), 4M19/2 (436 nm), 4G9/2 (446 nm), and 4I13/2 (470 nm). The transition from 6F7/2 to 6P3/2 depicts the prominent intensity at 404 nm. Hence, this wavelength is used for exciting the dopant ions to record the emission spectra of the present set of NP’s. It also matches well with the near UV LED wavelength, suggesting that this level (6F7/2→ 6P3/2) of the CTO NPs (phosphors will be effectively populated by near NUV LED excitation [52, 53] and hence can be a potential candidate for WLED applications [54]. Figure 19b depicts the recorded emission spectra of CTO NPs excited at 404 nm. The spectra contain four characteristic optical transition emission peaks such as 4G5/2 → 6H5/2 (565 nm) forbidden magnetic-dipole (MD) transition (ΔJ = 0 i.e., J ≠ 0 ↔ 0 values), 4G5/2 → 6H7/2 (600 nm) partial MD and partial electric-dipole (ED) allowed transition one with selection rule ΔJ = ± 1, 4G5/2 → 6H9/2 (649 nm) pure ED transition with ΔJ = ± 2 having moderate intensity and 4G5/2 → 6H11/2 (692 nm) forbidden transition with ΔJ = ± 3 having very weak intensity can be observed in the emission peaks that the intensity at 600 nm is the highest in comparison to other transitions, resulting emission at reddish-orange region. In our present work, the process of energy transfer beyond Ti3+ is between neighboring Ti ions which may become dominant since there is a transfer of energy from an excited Ti active ion to an non-excited titanium ion through encounters before it gets radiated through cross-relaxation (CR) process, such as: (4G5/2, 6H5/2 →6F5/2,6F11/2), (4G5/2, 6H5/2 → 6F7/2, 6F9/2), (4G5/2, 6H5/2 → 6F9/2, 6F7/2), and (4G5/2, 6H5/2 → 6F11/2, 6F5/2) as shown Fig. 19c [54]. The ‘Q’ value was calculated by plotting log (I/x) vs. log x (Fig. 19d) and the value is found to be 7.358 which is equal to ~ 7 indicates that dipole–dipole interaction is responsible for concentration quenching in CTO NPs. Fig. 20a CIE and b CCT diagram of CTO NPs a CIE and b CCT diagram of CTO NPs The Commission International de l’Éclairage (CIE) 1931 standard color coordinates were employed to estimate the emission color of CTO nanoparticles (NPs) from their photoluminescence spectra. In the CIE color space, the chromaticity coordinates (x, y) are used to specify color quality and to evaluate phosphor performance, and they represent the most prominent colorimetric parameters. Figure 20a illustrates the CIE 1931 chromaticity diagram of CTO NPs excited at 404 nm. The calculated CIE color coordinates are summarized and plotted in Fig. 20(a) to determine the dominant emission color of the CTO nanoparticles. The obtained (x, y) coordinates are located in the blue to blue-green region of the chromaticity diagram, indicating that the visible emission predominantly originates from defect-related states, such as oxygen vacancies and Ti3+ centers, within the CaTiO3 lattice. This behavior is consistent with the broad photoluminescence emission band observed in the visible region. Furthermore, the average correlated color temperature (CCT) was determined to be approximately 6500 K, placing the emission in the cool-white to blue region of the spectrum (Fig. 20b). Correlated color temperature (CCT) can be determined by Planckian locus, which is just a small portion of the (x, y) chromaticity diagram and several operating points occur beyond the Planckian locus. If a light source coordinate doesn’t fall on the Planckian locus, the CCT has been used to define a light source color temperature. CCT was obtained by transforming the light source coordinates (x, y) into (U’, V’) using the following Eqs. (1) and (2), and by setting the temperature of the closest point of the Planckian locus to the light source on the (U’, V’) uniform chromaticity diagram Fig. 20b [52].9\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:{U}^{{\prime\:}}=\frac{4x}{-2x+12y+3}$$\end{document}10\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:{V}^{{\prime\:}}=\frac{9y}{-2x+12y+3}$$\end{document} The relatively high CCT value further highlights the potential suitability of CTO nanoparticles for applications in blue-emitting phosphors, display technologies, and optoelectronic devices. Conclusions CTO nanoparticles were synthesized via solution combustion method using Aloe vera gel as a green and sustainable fuel exhibits remarkable structural, optical, photocatalytic, and electrochemical properties. The PXRD pattern confirms the formation of well-defined crystalline phases with a band gap of 3.12 eV, indicating good light absorption characteristics suitable for photocatalytic applications. The use of Aloe vera contributes to a higher density of oxygen vacancies and surface defects in the CTO structure, which significantly enhances its photocatalytic performance. This is evidenced by the decolorization efficiency of Malachite Green (MG), achieving efficiencies of 90.44% under UV irradiation and 57.88% under sunlight for a duration of 120 min. Scavenger tests reveal that photogenerated holes (h+) play a dominant role in the degradation mechanism, highlighting the effective charge separation and reactive species generation capabilities of the material. Electrochemical studies of CTO NPs such as Cyclic voltammetry (CV) indicate improved redox reversibility, while electrochemical impedance spectroscopy (EIS) analysis reveals a lower charge transfer resistance (Rct) key indicator of superior interfacial charge transport. Moreover, the prepared CTO NPs demonstrate good sensitivity in glyphosate detection having linearity (R2 > 0.96) across 1–6 µM concentration with LOD 0.38 µM and sensitivity ~ 0.25 µA µM−1. as confirmed by linear electrochemical responses and rapid current-time profiles in amperometric and voltametric studies. Overall, the incorporation of Aloe vera gel as a bio-fuel not only supports eco-friendly synthesis but also enhances the functional performance of CTO NPs across photocatalytic, electrochemical, and sensing applications, making them promising candidates for environmental remediation and agrochemical monitoring. Supplementary Information Below is the link to the electronic supplementary material. Supplementary Material 1. Supplementary Material 1.