A novel univariate legendre polynomial method for probabilistic failure load prediction in composite open-hole laminate Authors: Mingxuan Li, Ben Yuan, Fugui Li, Yuan Fang, Xiaolei Zhu Published: 2025 ABSTRACT A novel univariate Legendre polynomial method is proposed for probabilistic failure load prediction in composite open-hole laminate based on the dimension-reduction method and Legendre polynomial. The effectiveness of the method was verified by comparison with experimental results. The mean prediction error was less than 3%, and the coefficient of variation of the prediction error was less than 15%, indicating that the new method can effectively predict the probabilistic failure load of composite open-hole laminate. In addition, ULAM was compared with RSM and Kriging model to verify its superiority. Given the same number of sample points, ULAM achieved higher prediction accuracy than the other two models. Finally, the effect of the polynomial order on the prediction accuracy of ULAM was investigated. If the order is too low, underfitting will occur. While increasing the order can improve the prediction accuracy, an excessively high order leads to overfitting, which in turn degrades the model’s performance. Introduction The fiber-reinforced composite is widely used in aerospace, transportation and other fields owing to the advantages of light weight, high specific strength, high specific stiffness, fatigue resistance and designability1–3. In the actual application process, the composite structure is often necessary to open holes for the requirement of structural function and connection between components. However, due to the uncertainty of the manufacturing processes and material parameters, the mechanical properties of composite open-hole laminate are dispersed moderately, which endangers the safety and reliability of the composite structure4,5. However, the traditional safety factor method cannot quantify the probability of failure risk and is also difficult to fully tap the potential of material performance. Probability analysis methods can directly quantify the failure probability of structures under uncertainty, thereby providing a theoretical basis for reliability optimization design and achieving a balance between safety and economy6. Therefore, the probabilistic analysis method should be used to predict the strength of the composite open-hole plate to guarantee its safety in actual application process7,8. Monte Carlo Simulation (MCS) is a well-established and frequently used technique for probabilistic analysis. Wan et al.9 predicted the damage progression and strength probability distribution of composite laminates based on MCS. Lubritz et al.10 utilized MCS to investigate the influence of microscopic mechanical property parameters on the tensile properties of composite laminated plates. The calculation results show that this method is applicable to calculating the average and standard deviation of most linear material parameters of the studied carbon fiber-reinforced polymer (CFRP). Tang et al.11 conducted a detailed probability analysis based on multi-scale uncertainty propagation to quantify the failure probability of the design criterion relative to the static damage initiation and the prestressed vibration resonance margin. The failure probability of the damage initiation of the composite laminate was predicted using MCS. Mukherjee et al.12 studied the effect of material parameter uncertainty on the design of laminated composite using MCS. However, MCS suffers from high computational cost. To improve efficiency, scholars have adopted moment methods to solve uncertainty problems. Lin et al.13 studied the probabilistic failure of laminate composite plates based on the first-order second moment method. However, even a small error in the probability density function will lead to poor accuracy. Surrogate models were introduced for probabilistic analysis of composites to improve the calculation accuracy14. Zhou and Haeri et al.15,16 carried out the reliability and sensitivity of composite structures using the adaptive Kriging surrogate model. Soares et al.17,18 adopted response surface method to study the failure probability of composite plates under low-velocity impact account for the uncertainties of material properties and initial impact velocity. Carrere et al.19 studied the effect of the uncertainty parameter on the composite structure using response surface method. When the surrogate models are used to deal with hig \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\boldsymbol{F}}={\boldsymbol{G}}\left( {\boldsymbol{x}} \right)={\boldsymbol{G}}\left( {{x_1},{x_2}, \cdots ,{x_n}} \right)$$\end{document} h-dimensional nonlinear problems, a large number of sample points are required to obtain higher prediction accuracy. Li and Qiu et al.20,21 used a novel uncertainty analysis method based on the polynomial to assess the reliability of composite materials, which lacked experimental validation. In conclusion, the calculation accuracy of the existing probability analysis methods when dealing with high-dimensional nonlinear problems is closely related to the number of sample points. Although the prediction accuracy can meet the engineering requirements, the calculation cost is huge. Therefore, it is highly necessary to establish a prediction model that requires only a small number of sample points without reducing accuracy. In this paper, a probabilistic failure load prediction method for composite open-hole laminate was proposed combining the dimension reduction method (DRM) and Legendre polynomial (LP). Considering the uncertainty of material parameters, a univariate Legendre approximation model (ULAM) is established. To verify the correctness of the model, static tensile experiments were carried out on composite open-hole laminates, and the ultimate loads were obtained. The predicted results were compared with the experimental results to verify the effectiveness of the method. In addition, a comparative analysis was conducted with the existing prediction models, which proved that the proposed prediction model has certain superiority. Probabilistic model of composite open-hole The composite open-hole laminate is manufactured with carbon-fiber-reinforced composite material. The overall size of the composite open-hole laminate is 200 mm×36 mm×3.6 mm. A perforation with a diameter of 6 mm is located at the center of the plate, as shown in Fig. 1. The fiber layer order is [45/0/−45/90]2s. Fig. 1The configuration of composite open-hole laminate. The configuration of composite open-hole laminate. Due to the complexity of the preparation process, the mechanical properties of the composite open-hole laminates have a certain dispersion. If the factors affecting the ultimate load are taken as random variables, and the ultimate load is taken as the response value, the structural response function can be expressed as:1\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\boldsymbol{F}}={\boldsymbol{G}}\left( {\boldsymbol{x}} \right)={\boldsymbol{G}}\left( {{x_1},{x_2}, \cdots ,{x_n}} \right)$$\end{document} where F is the ultimate load of\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${G_0}={\boldsymbol{G}}(\boldsymbol{\mu}){\boldsymbol{x}}=\left( {{x_1},{x_2}, \cdots ,{x_n}} \right)$$\end{document} open-hole laminate under t\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\boldsymbol{\mu}{\mathrm{=}}\left( {{\mu _1},{\mu _2}, \cdots ,{\mu _n}} \right)$$\end{document}ensile, xi is the random variable. In this paper, the fiber parameters are taken as random variables, with the statistical characteristics shown in Table 1. All random variables are first assumed to follow normal distributions with setting the coefficients of variation equal to 0.0522. Table 1Statistical characteristics of random variables.ParameterMeanStandard deviationDistributionElastic modulus(GPa) E 11 1256.25NormalE22 = E338.1930.40965NormalPoisson’s ratioν12 = ν130.3-- ν 23 0.4--Shear modulus(GPa)G12 = G133.3070.16535NormalG233.1510.15755NormalTensile strength(MPa) X T 160080NormalYT=ZT251.25NormalComprehensive strength (MPa) X C 592--YC=ZC98--Shear strength(MPa)S12 = S13532.65Normal S 23 381.9Normal Table 1Statistical characteristics of random variables.ParameterMeanStandard deviationDistributionElastic modulus(GPa) E 11 1256.25NormalE22 = E338.1930.40965NormalPoisson’s ratioν12 = ν130.3-- ν 23 0.4--Shear modulus(GPa)G12 = G133.3070.16535NormalG233.1510.15755NormalTensile strength(MPa) X T 160080NormalYT=ZT251.25NormalComprehensive strength (MPa) X C 592--YC=ZC98--Shear strength(MPa)S12 = S13532.65Normal S 23 381.9Normal Statistical characteristics of random variables. Elastic modulus (GPa) Shear modulus (GPa) Tensile strength (MPa) Shear strength (MPa) Dimension reduction method The structural response function G(x) consists of n-dimensional random variable, as a continuously differentiable real-valued function, which can be expressed as a sum of lower-order functions in an increasing hierarchy23–25.2\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{gathered} {\boldsymbol{F}}{\mathrm{=}}{\boldsymbol{G}}\left( {\boldsymbol{x}} \right)={G_0}+\sum\limits_{{i=1}}^{n} {{{\boldsymbol{G}}_i}({x_i})} +\sum\limits_{{1 \leqslant i \leqslant j \leqslant n}} {{{\boldsymbol{G}}_{ij}}} ({x_i},{x_j})+ \cdots + \\ \sum\limits_{{1 \leqslant {i_1}< \cdots <{i_k} \leqslant n}} {{{\boldsymbol{G}}_{{i_1}{i_2} \cdots {i_k}}}} ({x_{{i_1}}},{x_{{i_2}}}, \cdots ,{x_{{i_k}}})+ \cdots +{{\boldsymbol{G}}_{12 \cdots n}}({x_1},{x_2}, \cdots ,{x_n}) \\ \end{gathered}$$\end{document} where G0 is the zeroth-order effect, which is a constant, and the first-order component function Gi(xi)gives the independent contribution to F by the i-th random variable acting alone, the second order component function Gij (xi, xj) gives the pair correlated contribution to F by the random variables xi and xj, etc. The last term G12…n (x1, x2,…, xn) contains any residual n-th order correlated contribution of all random variables. Based on the theoretical method of center point dimensionality reduction26, each sub-function of Eq. (2) is expanded at a specified point, and each sub-item expression after expansion is:3\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${G_0}={\boldsymbol{G}}(\boldsymbol{\mu})$$\end{document}4\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${{\boldsymbol{G}}_i}({x_i})={\boldsymbol{G}}\left( {{\mu _1}, \cdots ,{\mu _{i - 1}},{x_i},{\mu _{i+1}}, \cdots ,{\mu _n}} \right) - {G_0}$$\end{document}5\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{gathered} {{\boldsymbol{G}}_{ij}}({x_i},{x_j})={\boldsymbol{G}}\left( {{\mu _1}, \cdots ,{\mu _{i - 1}},{x_i},{\mu _{i+1}}, \cdots ,{\mu _{j - 1}},{x_j},{\mu _{j+1}}, \cdots ,{\mu _n}} \right) - \hfill \\ {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {{\boldsymbol{G}}_i}({x_i}) - {{\boldsymbol{G}}_j}({x_j}) - {G_0} \hfill \\ \end{gathered}$$\end{document}6\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{gathered} {{\boldsymbol{G}}_{ijk}}({x_i},{x_j},{x_k})={\boldsymbol{G}}\left( {{\mu _1},{\mu _2}, \cdots ,{x_i},{x_j},{x_k}, \cdots ,{\mu _n}} \right) - {{\boldsymbol{G}}_{ij}}({x_i},{x_j}) - \hfill \\ {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {{\boldsymbol{G}}_{ik}}({x_i},{x_k}) - {{\boldsymbol{G}}_{jk}}({x_j},{x_k}) - \hfill \\ {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {\kern 1pt} {{\boldsymbol{G}}_i}({x_i}) - {{\boldsymbol{G}}_j}({x_j}) - {{\boldsymbol{G}}_k}({x_k}) - {G_0} \hfill \\ \end{gathered}$$\end{document}7\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\begin{gathered} {{\boldsymbol{G}}_{12 \cdots n}}({x_1},{x_2}, \cdots ,{x_n})={\boldsymbol{G}}\left( {\boldsymbol{x}} \right) - {G_0} - \sum\limits_{{1 \leqslant i \leqslant n}} {{{\boldsymbol{G}}_i}({x_i}) - \sum\limits_{{1 \leqslant i