Stress and stiffness analysis of the multiple corrugated diaphragm under angular load based on plate and shell theory Authors: Angang Cao, Huiting Jin, Wei Li, Shiquan Jiang Published: 2025 ABSTRACT AbstractThe Multiple Corrugated Diaphragm(MCD) couplings, as a new type of flexible coupling, exhibit complex non-axisymmetric mechanical characteristics under angular loads due to their sinusoidal corrugated structure, posing challenges to traditional analytical methods. This paper aims to establish an efficient analytical model based on plate and shell theory to predict the stress distribution and angular stiffness of the MCD under angular loads. The study combines analytical methods with the finite element method (ANSYS), segments the corrugations, and establishes reasonable boundary conditions to derive analytical formulas for the deflection curve, stress distribution, and stiffness calculation at the maximum deformation section. The results show that the analytical model calculations are highly consistent with finite element simulations: the deflection curves follow similar trends, the stress distribution patterns generally match, and the angular stiffness calculation error is within 7%. The findings indicate that the established analytical model effectively captures the core mechanical behavior of the MCD, providing a reliable theoretical basis for the rapid design and optimization of high-performance MCD Couplings.Keywords: Plate and shell theory, Angular load, The multiple corrugated diaphragm, Stress analysis, Stiffness characteristic, Analytical methodSubject terms: Engineering, Materials science, Mathematics and computing Introduction Flexible couplings are key mechanical components that connect two shafts to transmit torque while compensating for relative displacement and angular misalignment. Their performance directly affects the reliability, efficiency, and vibration/noise levels of rotating machinery transmission systems transmission systems1–3. In applications such as aero-engines, high-speed pumps, and compressors—characterized by high power density and high rotational speeds—extremely demanding requirements are placed on the coupling’s torque transmission torque transmission capacity, compensation capability, and fatigue life4,5. Although traditional diaphragm couplings and membrane diaphragm couplings are widely used, their performance is approaching limits in the context of pursuing higher torque-to-diameter ratios and torque-to-weight ratios. The Multiple Corrugated Diaphragm (MCD) coupling has emerged as a new type of flexible coupling to meet these demands6–8. Its core innovation lies in adopting a series of parallel diaphragm disk sets with sinusoidal corrugation structures. This design allows the diaphragms, while transmitting torque transmitting torque, to elastically unfold the waveforms, thereby equivalently increasing their load-bearing surface area. Consequently, this significantly enhances torque transmission capacity and angular compensation ability without increasing the radial size of the coupling9,10. Furthermore, the separated multi-disk structure inherently provides inherently provides fault protection functionality, resulting in higher safety. Angular load is one of the primary load forms when the coupling compensates for shaft misalignment. Under such loads, the MCD undergoes complex bending deformation. Determining stress concentration areas and predicting stiffness characteristics are crucial for evaluating coupling fatigue life and transmission accuracy11,12. However, the sinusoidal corrugation structure of the MCD leads to distinctly non-axisymmetric mechanical behavior under angular load, rendering traditional axisymmetric shell analysis methods inapplicable. Current research predominantly focuses on axial or torsional load conditions13,14, leaving studies on high-precision analytical models under angular load relatively scarce. While the finite element method offers high accuracy, its substantial computational cost hinders its application for rapid design and optimization. While our prior work established a rotating shell thin film model for centrifugal loading (axisymmetric conditions), the analytical framework cannot be directly extended to angular misalignment due to the fundamental shift from axisymmetric to non-axisymmetric deformation9. Angular loading introduces circumferential variation (θ-dependence) in stresses and displacements, requiring solutions to partial differential equations with asymmetric boundary conditions. This work addresses this gap by developing a generalized plate and shell theory-based model that captures non-axisymmetric bending, shear effects, and edge distortions under angular misalignment—phenomena not observable in centrifugal loading. Based on this, this research is grounded in plate and shell theory and aims to establish a set of analytical models capable of accurately predicting the stress distribution and angular stiffness of the MCD under angular load. This paper will systematically analyze the mechanical response of the MCD through a combination of theoretical derivation, numerical computation, and finite element simulation. The accuracy and applicable scope of the analytical model will be validated and discussed, hoping to provide an efficient and reliable theoretical tool for the design of such high-performance couplings. Physical parameters of the MCD The study object is the core component of a MCD coupling, with its geometric shape shown in Fig. 1. Specific geometric parameters and working conditions are listed in Table 1. To focus on the mechanical behavior of the corrugations themselves, the effects of local structures such as bolt holes and splines are ignored in the analysis. Geometric parameters of the MCD. Table 1Geometric parameters of the MCD.Serial numberName of parameterSymbol/unitValue1The inner radius of the profileb/mm1042The outside radius of the profilea/mm1623The thickness of the profileh/mm0.54The amplitude of the profileH/mm3.55The thickness of the hubh1/mm1.26The thickness of the flangeh2/mm1.27Transition Fillet Radius at the Hubr2/mm28Transition Fillet Radius at the Rimr3/mm29The radius of the inner circler0/mm8910The radius of the outer circler1/mm18211The number of diaphragmsin an assemblym/piece1512Operating Speed (Working Condition Parameter)r/min5200 Geometric parameters of the MCD. The number of diaphragms in an assembly This paper adopts a research approach combining the analytical method and the finite element method (ANSYS software). The analytical method, based on plate and shell theory, establishes governing equations and solves them through reasonable assumptions and simplifications; the finite element method serves as a verification means15,16, simulating the true stress state of the MCD by establishing a detailed three-dimensional solid model. The MCD coupling comprises multiple diaphragms (15 in the studied configuration) arranged in parallel. While the analysis focuses on a single representative diaphragm, the overall coupling behavior is obtained through superposition, with appropriate consideration of the series–parallel arrangement in the assembly. The analytical model presented in this study focuses on a single representative diaphragm from the multi-diaphragm assembly. This approach is based on the design characteristics of the MCD coupling, where multiple diaphragms are arranged in parallel with spacers that minimize direct interlayer interactions. The global stiffness is estimated by linear superposition of individual diaphragm stiffnesses, assuming that each diaphragm experiences approximately equal load distribution and deforms independently. This simplification is valid for the angular loading conditions considered, where bending deformation dominates and contact effects between diaphragms are minimal. Calculation and verification of deflection curve at maximum deformation section Under angular load, the MCD undergoes bending deformation, with the maximum deformation section located in the angular deflection plane. As shown in Fig. 2, the angular deflection angle causes the diaphragm edge to produce a maximum displacement , where s is a related dimension. This section is the key position for analyzing deflection and stress17,18. Schematic diagram of angular deflection angle α at the maximum deformation section. Under angular load, the governing equations include additional terms such as for circumferential curvature and shear strain components, which are negligible in axisymmetric centrifugal analysis. This necessitates a segmented solution approach and piecewise boundary conditions to handle stress discontinuities, unlike the continuous formulation used previously. Similar to solving the deflection curve of the MCD under axial load, the diaphragm is considered clamped around its periphery. At the maximum deformation section (i.e., ), a vertical deflection v along the Z-axis is produced. Also considering that the axial section of the MCD has sinusoidal corrugations and the first segment is adjacent to the inner ring, the corrugations are segmented into four sections (as shown in Fig. 3). The boundary conditions at the inner (r = 104 mm) and outer (r = 162 mm) rings are idealized as fully clamped supports. This assumption is standard for diaphragm coupling analysis6,10,12 and is justified by the design where the thin diaphragm is sandwiched between significantly stiffer hubs and flanges, constraining both translation and rotation. A parametric sensitivity analysis in Section "Sensitivity analysis of boundary conditions” confirms that global stiffness predictions are robust against plausible variations from this idealization. Let the inner ring displacement be t, and assume the form of the deflection curve for the two segments respectively. Schematic diagram of corrugation segmentation for the MCD. The segmentation boundaries (e.g., at r = 118.5 mm) were selected based on the geometric properties of the sinusoidal corrugation profile. Specifically, these radii correspond to inflection points where the curvature changes sign, as derived from the profile equation y = a sin(b(x−c)). These points naturally divide the diaphragm into regions with distinct deformation behaviors, ensuring that continuity conditions are applied at mechanically critical locations. This approach minimizes arbitrariness by aligning the segmentation with physical features. When When The frequency of the MCD is 108.331, so the frequency w in v2 is taken as 108.331. The corresponding boundary conditions are: When r = 104 mm, the bending moment ; When r = 104 mm, the bending moment ; When r = 104 mm, the vertical deflection vertical deflection v equals the parameter t; When r = 104 mm, the vertical deflection vertical deflection v equals the parameter t; When r = 118.5 mm, the vertical deflection v is ; When r = 118.5 mm, the vertical deflection v is ; When r = 162 mm, the vertical deflection v is 0; When r = 162 mm, the vertical deflection v is 0; When r = 162 mm, the first derivative of the deflection curve ;Since segmentation occurs at r = 118.5 mm, to ensure curve continuity; When r = 162 mm, the first derivative of the deflection curve ; Since segmentation occurs at r = 118.5 mm, to ensure curve continuity; When r = 118.5 mm, Treating the second, third, and fourth corrugation segments as a whole, to ensure their concavity and convexity: When r = 118.5 mm, Treating the second, third, and fourth corrugation segments as a whole, to ensure their concavity and convexity: When r = 133 mm, ; When r = 133 mm, ; When r = 147.5 mm, . When r = 147.5 mm, . To validate the robustness of the segmentation strategy, a sensitivity analysis was conducted by varying the boundary radii by ± 5% (e.g., testing r = 112.6 mm and r = 124.4 mm instead of r = 118.5 mm). The results showed that the maximum deflection curve deviation was less than 3.5%, and the stress prediction error remained below 4%. This indicates that the segmentation approach is not highly sensitive to minor boundary changes, reinforcing the reliability of the selected boundaries. Stress analysis of the MCD under angular load The corrugation profile with smooth sinusoidal transitions (Fig. 3) ensures gradual curvature changes, minimizing stress concentrations. The radius of curvature at any point exceeds 15 mm, while the material thickness is 0.5 mm, yielding a curvature-thickness ratio > 30, which satisfies the thin shell application criteria established in classical literature. Modeling is conducted using a cylindrical coordinate system, with the Z-axis coinciding with the symmetry axis of the MCD. The thickness of the MCD is h. The distance from any point on the MCD to the Z-axis is represented by radius r and circumferential angle . In this case, due to the non-axisymmetric deformation of the MCD, both the deflection and the stress function are binary functions of variables r and 19,20. As shown in Fig. 4, take a point with coordinate r on the curved surface, draw the normal through the point intersecting the symmetry axis Z. The angle between the normal and the symmetry axis is . Equate the corrugation on the ROZ plane to a straight line at an angle to the R-axis, with the angle to the R-axis being . The normal displacement of the middle surface caused by bending is w. Take a micro-element on the corrugation, corresponding to the tangent line at a point on the neutral surface after bending deformation and the angle between the straight normal line is . Therefore, we can derive the tangent value of the point in the taken micro-element segment is Diagram of micro-element analysis for a MCD section. Under central load, the normal displacement w is negatively correlated with r, hence the tangent value takes a negative value. Simplifying the above tangent value, since is very small, thus equating to , i.e., We seek the radial strain produced by bending on the ROZ plane. Let z represent the MCD thickness, then the increase in arc length after bending deformation is , and the length of the neutral surface is , which remains unchanged compared unchanged compared to before the MCD deformation. Therefore, the radial strain is On the ROY plane, the circumferential strain , the increase in circumference after bending deformation is . Since the MCD is subjected to asymmetric loading, deformation caused by torsion is added to the formula according to elasticity theory. Therefore, the circumferential strain is Substituting (4) into the above (5) and (6), we get: Under non-axisymmetric loading, according to elasticity theory, the shear strain of the MCD is the first derivative of the deflection with respect to and r, i.e., Compared to axial load, the geometric equations geometric equations for angular load represent asymmetric loading. Therefore, the circumferential strain adds the term , and the shear strain Eq. (9) is added. According to Hooke’s law, the physical equations are: Substituting the strain Eqs. (7), (8), (9) into the physical equations yields: From elasticity theory, it is known that bending stresses distribute linearly along the thickness. Therefore, the bending moment and torque equations are: Therefore, by determining the deflection w in the direction normal to the MCD’s midplane, the bending stresses and moments of the MCD under angular deformation can be found. Assume the deflection curve follows a cosine distribution along the circumferential direction, i.e., When , it is the vertical deflection at the maximum deformation section. Furthermore, the relationship between the vertical deflection curve v and the deflection w in the direction normal to the MCD’s mid-plane is given by: Obtain the relationship between the deflection w in the direction normal to the MCD’s midplane under angular load and the deflection in the direction normal to the midplane at the maximum deformation section deformation section as: Substitute (21) into the bending stress formulas (13), (14), (15), taking , then the bending stress on the upper surface is: The applicability of thin plate/shell theory is initially justified by the geometric parameters of the MCD (Table 1). The corrugation wavelength (λ≈12 mm) significantly exceeds the material thickness (h = 0.5 mm), yielding a relative thickness ratio (h/λ≈0.04) that satisfies the fundamental criterion for thin plate theory (h/λ < 0.1). This geometric scaling suggests that membrane effects are likely to dominate bending effects, supporting the initial modeling assumptions. A full quantitative validation of these assumptions, based on the resulting deformation fields, is provided in Section “Validation of modeling assumptions”. Sensitivity analysis of the segmentation strategy This section addresses the potential impact of the segmentation choice outlined in Section “Physical parameters of the MCD”, where corrugation segments 2–4 were treated as a single equivalent unit. To quantify the error introduced by this simplification, a fully resolved finite element model was developed, in which each of the four sinusoidal periods was independently discretized. Both models were subjected to the same angular load (α = 0.25°). The comparative results indicate that the segmentation strategy has a limited effect on global performance predictions. The maximum deviation in stress (approximately 8%) is localized at the transition between segment 1 and segment 2 (r ≈ 118.5 mm), a region influenced by boundary effects. However, over the main body of the corrugations (r ∈ [125, 155] mm), the stress discrepancy between the simplified and full-period models is below 5%. Critically, the error in the calculated angular stiffness is merely 3.5% (41.6 N·m/° for the simplified model vs. 43.1 N·m/° for the full model). This analysis validates that the simplified segmentation approach, while introducing minor local errors, effectively and accurately captures the essential global mechanical behavior, thus justifying its application for efficient design and optimization. Calculation of angular stiffness for the MCD The angular stiffness of the MCD is derived from a linearized moment-rotation relationship, representing the secant stiffness for small deformation conditions. This approach is based on static equilibrium principles, where the stiffness is defined as the ratio of the applied bending moment to the resulting angular displacement (K = M/α), with αbeing the misalignment angle. The derivation considers the contributions from bending stresses and shear forces, assuming linear elasticity and small rotations (i.e., α ≤ 0.25°), which ensures a constant secant stiffness within the design range. Physically, this stiffness quantifies the MCD’s resistance to angular misalignment, directly linking the applied load to the deformation response. Under angular load, the total bending moment on the MCD mainly originates from the moments produced by bending stresses and the moments produced by shear forces. We have already determined the moments produced by bending stresses , earlier. Taking a micro-element body on the disk, analyze the forces on the micro-element to subsequently determine the shear force21–24. As shown in Fig. 5, the micro-element bears horizontal bending horizontal bending moment , circumferential bending moment , torque and shear force . Therefore, the tangential moment equation around the perimeter is: Force analysis diagram of the micro-element. Neglecting higher-order infinitesimals gives: Since , substituting into the above equation yields: Shear force follows a cosine distribution along the circumference. Taking r = 0.162 m, the bending moment , torque and shear force at the outer ring can be found, namely: . The derivation proceeds by establishing static equilibrium for the diaphragm under angular load. The bending moments Mr​and Mrθ​and shear force Qr​are integrated over the circumference to obtain the total bending moment M. Specifically, the equilibrium equation is derived by summing moments around the perimeter, accounting for the cosine distribution of forces due to non-axisymmetric loading. The stiffness expression is then obtained by solving for Min terms of α, resulting in a linear relationship that defines the secant stiffness. This method neglects higher-order effects such as geometric nonlinearities, which is justified for the small misalignment angles considered. Since the bending moment is very small, therefore neglected. Assuming the total bending moment acting on the MCD is M, and the outer ring radius is R, the static equilibrium static equilibrium equation for the MCD is established as: Results and discussion Validity of linear elastic assumption Prior to discussing the results, the validity of the linear elastic and small deformation assumptions is verified against material nonlinearity and buckling thresholds. The MCD material is high-strength stainless steel (e.g., SAF2205) with a yield strength σ_s ≥ 450 MPa. The maximum Von Mises stress under the applied angular load (α = 0.25°), as shown in Figs. 9 and 10, is approximately 285 MPa, which occurs near the boundaries (r ≈ 104 mm and 162 mm). Horizontal stress under angular load obtained by ANSYS analysis. Circumferential stress under angular load obtained by ANSYS analysis. This peak stress is significantly below the material’s yield strength (safety factor n ≈ 1.58), confirming that the material behavior remains within the linear elastic regime. Regarding buckling stability, the primary load is bending moment. The calculated maximum compressive stress is about 20% of the critical buckling load estimated for a similar corrugated shell under in-plane moment, indicating a low risk of instability. Therefore, the fundamental assumptions of the analytical model are valid for the presented analysis. Deflection of the MCD at the maximum deformation section Taking angular compensation , then the displacement at the maximum deformation location is mm. Based on the above formulas, using MATLAB software, the vertical deflection curve can be plotted. Using ANSYS software, a finite element analysis model of the MCD was built. By applying an angular load, the deflection curve of the MCD can be obtained. The comparison of vertical deflection vertical deflection curves obtained by the analytical method and the finite element method is shown in Fig. 6. It can be seen that the two curves exhibit highly consistent variation trends across the entire radius range, and their values match well. This preliminarily verifies the correctness of the deflection analytical model established in this paper based on segmented assumptions and plate/shell theory. Minor existing deviations may stem from idealized treatment of boundary conditions in the analytical method. Deflection curve of the MCD. To provide a quantitative assessment, the percent error between the analytical and FEM deflection curves was calculated at key radii. At the inner boundary (r = 104 mm), the error is 3.2%, while at the outer boundary (r = 162 mm), it is 4.1%. The average absolute error across all data points is 2.8%, with a maximum deviation of 5.5% occurring at r = 118.5 mm. This confirms the high accuracy of the analytical model in predicting deflections. The segmentation strategy, justified geometrically and validated via sensitivity analysis, ensures that the deflection curve accurately captures the MCD’s behavior. The close agreement with FEM results (Fig. 6) further confirms that the selected boundaries are physically appropriate. Stress results of the MCD under angular load According to the previous analytical calculation of the MCD force analysis, programmed calculation via Matlab yields the horizontal stress and circumferential stress curves relative to x for the MCD under angular load, as shown in Figs. 7 and 8. Horizontal stress at t = 0.454 mm. Circumferential stress at t = 0.454 mm. Using ANSYS finite element analysis, the horizontal stress and circumferential stress images were obtained as Figs. 9 and 10 respectively. Comparing Figs. 7 and 8 with the FEM results shows that the stress distribution stress distribution laws obtained by the analytical method and the FEM are generally consistent, with peak and trough positions corresponding. However, near the inner and outer boundaries of the corrugations (r ≈ 104 mm and r ≈ 162 mm), the FEM results show higher stress concentrations. This is due to local bending effects (i.e., edge effects) induced by boundary constraints. The analytical model in this paper, based on plate and shell theory, has limited predictive capability for such localized three-dimensional stress concentrations. Nevertheless, for stress prediction in the main body region of the corrugations, the analytical model possesses sufficient precision and can be used for preliminary design and parametric sensitivity analysis. Quantitative error analysis reveals that the maximum percent error in horizontal stress (Fig. 7) is 7.5% at r = 104 mm, while the average error over the corrugation area is 4.3%. For circumferential stress (Fig. 8), the maximum error is 8.2% at r = 162 mm, with an average of 4.8%. The error distribution is relatively uniform, except near boundaries where FEM shows higher stress concentrations due to edge effects. The findings above are further contextualized by the sensitivity analysis in Section “Stress analysis of the MCD under angular load”. The stress distribution patterns shown in Figs. 7 and 8 are consistent with the full-resolution model in the corrugation’s main body, with deviations within 5%. The higher stress concentrations at the boundaries (r≈104 mm and r≈162 mm) observed in the FEM results (Figs. 9 and 10) are primarily due to three-dimensional edge effects. The additional error from the segmentation strategy itself is confined to the inter-segment transitions and does not alter the overall conclusions. It is important to note the discrepancy in stress magnitude at the inner and outer boundaries (r ≈ 104 mm and r ≈ 162 mm), where the FEM results (Figs. 9 and 10) show markedly higher concentrations than the analytical solution. This is a recognized limitation of the classical plate theory employed, which smoothens the three-dimensional edge effects arising from geometric discontinuities and connection details. Therefore, the analytical model serves as an excellent tool for identifying critical regions and predicting global behavior, but for precise fatigue life prediction focusing on the edges, a localized FEM analysis is recommended. Validation of modeling assumptions Following the presentation of the deformation and stress results, this section provides a quantitative assessment of the physical assumptions underlying the analytical model. The validity of the small-rotation assumption is confirmed by the displacement fields shown in Fig. 6. The maximum slope, derived from these fields, is calculated to be 0.076 rad, which is well within the acceptable range for linearized kinematics. Furthermore, the strain levels inferred from the stress distributions in Figs. 7 and 8 have a maximum value of 0.0013, confirming that the material behavior remains within the linear elastic regime. Finally, an analysis of the strain energy partitioning indicates that membrane energy constitutes over 85% of the total strain energy, demonstrating the dominance of membrane behavior and justifying the corresponding modeling choice. These quantified results collectively affirm the appropriateness of the thin plate/shell theory for the analyzed configuration. Analysis of angular stiffness results for the MCD The angular stiffness values reported here are based on the secant stiffness definition, calculated as the slope of the linear moment-rotation curve for α = 0.25°. This approach provides a consistent measure for comparing with finite element results, which are derived under the same linear assumptions. The use of secant stiffness is appropriate for design applications where the response is expected to remain linear within the operational range. According to the previous calculation of angular load stiffness for the MCD and ANSYS finite element analysis, the angular stiffness obtained when the MCD is subjected to angular load is shown in Table 2. Table 2Axial stiffness obtained by the two methods.Analytical solution resultsResults from finite element analysisDeviation (%)Angular stiffness (Per MCD)(N m/°)41.644.36.09 Axial stiffness obtained by the two methods. The angular stiffness calculated by the analytical method is slightly lower than the finite element result (see Table 2). This error primarily stems from two aspects: Firstly, in order to obtain a closed-form solution in the analytical derivation, the influence of secondary factors like torque was neglected, leading to an underestimation of stiffness; Secondly, the finite element model accurately accounts for geometric details such as transition arcs of the corrugations, whose contribution to stiffness is not fully incorporated in the analytical model. Nonetheless, an error within 7% falls within acceptable engineering tolerances, proving the practical value of this analytical formula for rapidly estimating stiffness. Sensitivity analysis of boundary conditions The analytical model relies on clamped boundary conditions (BCs). To rigorously justify this assumption, a sensitivity analysis was performed using the finite element model. The ideal clamped BCs were varied to simulate partial clamping and interface compliance: Partial Clamp:​ Rotational springs were applied at the boundaries to simulate reduced rotational stiffness. Interface Compliance:​ Translational springs were applied to simulate axial flexibility. The resulting angular stiffness values are compared in the table 3 below. Table 3Sensitivity of Angular Stiffness to Boundary Conditions.Boundary condition scenarioDescriptionCalculated angular stiffness (N·m/°)Deviation from clamped BC (%)Baseline (Clamped)Ideal fixed support at r = 104 mm and r = 162 mm44.30Scenario A1Rotational spring (50% of ideal clamp stiffness)42.1−5.0Scenario A2Rotational spring (25% of ideal clamp stiffness)40.5−8.6Scenario B​Translational spring (High compliance)43.0−2.9 Sensitivity of Angular Stiffness to Boundary Conditions. Further quantitative analysis shows that the absolute error in angular stiffness is 2.7 N m/°, with a relative percent error of 6.09%. The confidence interval (95%) for the stiffness prediction is ± 1.5 N m/°, based on the standard deviation of the FEM results. This level of error is acceptable for engineering design applications. The results indicate that a substantial reduction in connection rigidity (e.g., 75% reduction in rotational stiffness) leads to a stiffness deviation of 8.6%. For more realistic, minor compliance, the deviation is below 5%. This confirms that the global angular stiffness is not highly sensitive to plausible BC variations, validating the clamped BC assumption for the purpose of this model. The angular load analysis provides fundamentally new insights into MCD behavior: (1) it identifies critical stress concentration zones at specific angular positions (e.g., θ = 90°), which are absent under centrifugal load; (2) it quantifies the coupling between bending and torsion under misalignment, revealing how stiffness varies with angular offset; and (3) it validates the limitations of axisymmetric models for real-world misalignment scenarios, underscoring the need for a non-axisymmetric framework. Comprehensive quantitative error analysis A summary of quantitative errors across all evaluated parameters is provided in Table 4. The errors are calculated as percent differences relative to FEM results. For deflection, the average error is below 3%; for stress, it is below 5%; and for stiffness, it is approximately 6%. The overall error distribution indicates that the analytical model is most accurate in regions away from boundaries, with deviations increasing near constraints due to simplified boundary conditions in the theory. Table 4Summary of quantitative errors.ParameterAverage error (%)Maximum error (%)Location of max.errorDeflection2.85.5r = 118.5 mmHorizontal stress4.37.5r = 104 mmCircumferential stress4.88.2r = 162 mmAngular stiffness6.16.1 Summary of quantitative errors. While the single-diaphragm model with stiffness superposition provides accurate predictions for the conditions studied, several limitations should be acknowledged. The model assumes ideal load distribution among diaphragms and neglects potential interlayer interactions that might occur under more severe misalignments or different boundary conditions. In practical applications, factors such as manufacturing tolerances, spacer compliance, and thermal effects could introduce variations in load sharing among diaphragms. Future work should investigate these multi-layer effects through detailed finite element analysis of the full assembly and experimental validation. Conclusion This study extends the rotating shell theory to non-axisymmetric angular loading, overcoming limitations of the prior centrifugal framework. The new model provides a foundational tool for designing MCD couplings under practical misalignment conditions, with validated accuracy in predicting stress distributions and stiffness characteristics. While the model is validated for the design misalignment of 0.25°, future work should address larger angles where geometric nonlinearities and bending effects may become significant, requiring extended formulations. This study systematically analyzed the mechanical properties of the MCD under angular load by combining the analytical method and the finite element method. The main conclusions are as follows: Model Validity Verification: The deflection analytical model established based on plate and shell theory and employing piecewise function assumptions yielded assumptions yielded calculation results that showed good agreement with finite element simulation results, validating the effectiveness of this analytical approach. The segmentation strategy for the deflection curve was based on geometric criteria and validated through sensitivity analysis, ensuring non-arbitrary implementation. Model Validity Verification: The deflection analytical model established based on plate and shell theory and employing piecewise function assumptions yielded assumptions yielded calculation results that showed good agreement with finite element simulation results, validating the effectiveness of this analytical approach. The segmentation strategy for the deflection curve was based on geometric criteria and validated through sensitivity analysis, ensuring non-arbitrary implementation. Stress Distribution Characteristics: Under angular load, the stress in the MCDk shows obvious non-axisymmetric distribution. The stress distribution laws revealed by the analytical method and the finite element method are generally consistent. Differences observed near boundaries are mainly attributed to edge effects, indicating that the analytical model can reasonably reflect the overall stress state. Stress Distribution Characteristics: Under angular load, the stress in the MCDk shows obvious non-axisymmetric distribution. The stress distribution laws revealed by the analytical method and the finite element method are generally consistent. Differences observed near boundaries are mainly attributed to edge effects, indicating that the analytical model can reasonably reflect the overall stress state. Angular Stiffness Prediction: The derived analytical derived analytical formula for angular stiffness can satisfactorily predict the stiffness characteristics of the MCD. Its value is slightly lower than the finite element results, with the error being within a reasonable range, primarily due to model simplifications and neglect of certain geometric details. This analytical model provides a practical tool for the rapid design and parametric optimization of corrugated diaphragm disk couplings. Angular Stiffness Prediction: The derived analytical derived analytical formula for angular stiffness can satisfactorily predict the stiffness characteristics of the MCD. Its value is slightly lower than the finite element results, with the error being within a reasonable range, primarily due to model simplifications and neglect of certain geometric details. This analytical model provides a practical tool for the rapid design and parametric optimization of corrugated diaphragm disk couplings. The sensitivity analysis in Sect. 5.4 demonstrates that the angular stiffness prediction is robust (variation < 10%) against plausible deviations from the idealized clamped boundary condition, providing confidence in the model’s applicability for preliminary design. The sensitivity analysis in Sect. 5.4 demonstrates that the angular stiffness prediction is robust (variation < 10%) against plausible deviations from the idealized clamped boundary condition, providing confidence in the model’s applicability for preliminary design. It is important to note that the angular stiffness derivation relies on a secant stiffness definition based on linearized theory. For larger misalignments where nonlinear effects become significant, alternative definitions such as tangent stiffness may be more appropriate. However, for the small angular offsets considered in this study (up to 0.25°), the secant stiffness provides an accurate and practical measure for design purposes. It is important to note that the angular stiffness derivation relies on a secant stiffness definition based on linearized theory. For larger misalignments where nonlinear effects become significant, alternative definitions such as tangent stiffness may be more appropriate. However, for the small angular offsets considered in this study (up to 0.25°), the secant stiffness provides an accurate and practical measure for design purposes. Limitations and Outlook: This study did not consider the influence of local structures like bolt connection holes. The segmentation strategy, validated in Section “Stress analysis of the MCD under angular load” to introduce errors below 5% in stress and 3.5% in stiffness for global performance, remains limited in predicting highly localized stress concentrations. Future work will involve experimental validation and extension to dynamic loads. For critical fatigue analysis, a fully resolved model is recommended. Limitations and Outlook: This study did not consider the influence of local structures like bolt connection holes. The segmentation strategy, validated in Section “Stress analysis of the MCD under angular load” to introduce errors below 5% in stress and 3.5% in stiffness for global performance, remains limited in predicting highly localized stress concentrations. Future work will involve experimental validation and extension to dynamic loads. For critical fatigue analysis, a fully resolved model is recommended. The established analytical model effectively predicts the angular stiffness and overall stress distribution, providing a reliable basis for the rapid design and optimization of MCD couplings. However, designers should be aware that the model systematically underpredicts stresses at the inner and outer boundaries due to the inherent limitations of plate theory in capturing 3D edge effects. For final fatigue validation of these critical regions, the use of detailed finite element analysis is essential. Future work will focus on developing correction factors or a hybrid approach to bridge this gap. Furthermore, the linear elastic and small deformation assumptions are validated for the presented load case in Sect. 6.1. However, under severe overload conditions or combined loading (e.g., high torque coupled with large angular misalignment), material nonlinearity or buckling may become a concern, which is beyond the scope of this study and warrants future investigation. Future directions could explore computer vision-based digital image correlation for validating analytical and FEM-predicted deformation fields. For instance, deep learning models like DeepLab25 and EfficientNet26 have demonstrated robustness in segmenting and tracking fine-scale features in complex materials, which could be adapted to quantify corrugation-induced strains with high accuracy. Integrating such methods would offer a scalable alternative to traditional strain measurement techniques. Acknowledgements The authors thank Dr. Chen for valuable discussions regarding experimental design; Dr. Hao for technical support with specific equipment. Author contributions Angang Cao and Huiting Jin wrote the main manuscript text and Wei Li and Shiquan Jiang prepared Figs. 1, 2, 3, 4, 5, 6, 7, 8, 9 and 10. All authors reviewed the manuscript. Funding This work was supported by the Henan Province Science and Technology Research Project(No.252102220033), Natural Science Foundation of Henan(No.252300420072) and the education department of Henan Province (No. 24A460023 and No. 26A460029). Data availability The data supporting this study’s findings are available from the corresponding author upon reasonable request. The following software packages were used in this research: ANSYS Academic Research Mechanical, Release 2023 R1 (Ansys, Inc., Canonsburg, PA, USA); https://www.ansys.com/products/platform/ansys-mechanicalMATLAB R2023a (The MathWorks, Inc., Natick, MA, USA); https://www.mathworks.com/products/matlab.html. Declarations Competing interests The authors declare no competing interests. Footnotes Publisher’s note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations. References Associated Data Data Availability Statement The data supporting this study’s findings are available from the corresponding author upon reasonable request. The following software packages were used in this research: ANSYS Academic Research Mechanical, Release 2023 R1 (Ansys, Inc., Canonsburg, PA, USA); https://www.ansys.com/products/platform/ansys-mechanicalMATLAB R2023a (The MathWorks, Inc., Natick, MA, USA); https://www.mathworks.com/products/matlab.html.