Optimization and physicochemical & antioxidant properties of leek (Allium porrum L.) dried by foam-mat drying Authors: Yasemin Yikilkan, Hojjat Pashazadeh, Sarhan Mohammed, Ilkay Koca Published: 2025 ABSTRACT The foam drying method has evolved as a novel food drying technique. In the present study, the foam-mat drying technique is used to produce powder from leek (Allium porrum L.). The proportions of foaming agents were systematically optimized using the response surface methodology (RSM) and central composite design model. The optimized formulation was identified as 1.50% carboxymethyl cellulose, 14.37% maltodextrin, and 8.93% egg white. The optimal composition was adjusted for achieving high foam stability, high volume, and low density. This improved formula was then freeze-dried and dried using hot air at 50 °C and 70 °C, and its physical and chemical properties, antioxidant abilities, and overall quality were analyzed afterward. Based on the data obtained, the Midilli model was identified as the most suitable drying model. The TPC values for the samples dried at 50 °C, 70 °C, and freeze-dried were 1340.31, 1368.87, and 1349.83 mg/kg, while the TFC values were 208.78, 225.61, and 225.61 mg/kg. The antioxidant activities measured using the ABTS, DPPH, and FRAP tests were 8.58, 16.18, and 13.83 mmol/g for ABTS; 3.43, 4.56, and 1.91 mmol/g for DPPH; and 1.04, 1.32, and 1.27 mmol/g for FRAP, respectively. Considering the types of volatile compounds and the qualities of the powder, the samples dried at 50 °C using the convective method showed the best outcomes. Introduction Allium species, a member of the Allieaceae family, are among the oldest cultivated vegetables and include onion, garlic, and leek1,2. It was used for medicinal purposes, as food, or as ornamental plants for more than 4000 years3. Most of these plants constituents have been shown to have rich nutritional and aromatic properties4. Leek (Allium porrum L.) is a common vegetable species belonging to the Allium genus. Its prevalence has surged as a result of the accumulation of knowledge5. Leeks exhibit a broad geographical distribution from Mediterranean countries, Mediterranean islands, Asia, Europe, North America, and North Africa to Southern England6. Renowned for their nutritional content and biological activities, they are among the most widely consumed vegetables globally. In addition to their nutritional value, they also take their place among herbal medicines7. Their abundance of bioactive compounds, including organic acids, phenolic compounds, carbohydrates, amino acids, and organosulfur compounds (OSB), are linked to their therapeutic qualities. Allium vegetables are rich in organosulfur compounds. They are believed to provide advantageous effects on health. Allium vegetables are highlighted for their use in pharmaceuticals and nutraceuticals. It demonstrates a wide range of therapeutic applications for its antihypertensive, antithrombotic, hypocholesterolemic, antimicrobial, antiviral, antidiabetic, anticarcinogenic, and antimutagenic properties8. Leeks’ composition and quality have been the subject of a great deal of research up to this point. Owing to its aromatic properties, it has been incorporated into pasta9, bread10, edible11, meat12 and cookies13 as a flavor enhancer or preservative. To guarantee the sustainable use of leeks, various contemporary drying techniques, including infrared14, microwave15, convective methods16, and freeze-drying17, were employed. To the best of our knowledge, there is no published research on foam mat drying leeks. Foam mat drying is a method that differs from conventional techniques employed to dehydrate liquid and semi-liquid food products. The materials are combined with diverse foaming agents and stabilizers, followed by drying post-foam production. It is important to highlight that various methods are available for drying the generated foam. As of now, numerous materials, including banana18, papaya19, guava20, apple juice21, honey22, coconut milk23, and fruit juice24, have been dehydrated using the foam mat drying technique. Through the use of leeks (Allium porrum L.), the purpose of this research is to develop a foam mat drying method. The experiment comprises two phases. Initially, the ratios of foaming agents and stabilizers were optimized through response surface methodology to ascertain the suitable proportions for drying conditions. In the subsequent phase, the chosen ratios are utilized to generate high-quality powder. Various analyses were conducted to determine total phenolic content (TPC), total flavonoid content (TFC), antioxidant activity, and FTIR spectra. Volatile compounds using GC-MS, color, dry matter, water activity, powder properties, and drying kinetics were also investigated. Material and method Physicochemical analysis of fresh Leek pulp A collection of leeks (Allium porrum L.) was acquired from Samsun, Turkey. Initially, the leek was cleaned and washed. Subsequently, the leaf portion was separated, and the white portions were crushed using a household blender (Arzum, Turkey) to obtain pulp. Various parameters were measured for the samples, including color, pH, total dry matter, total soluble solids (TSS, °Bx), water activity, total phenolic and flavonoid content, and antioxidant capacity25. Preparation of leek pulp for foam drying The pH of the resultant pulp was modified to 4.0 utilizing a citric acid solution. After being held at 60 °C for 5 min, it was quickly cooled. These specific time and temperature conditions help preserve the aroma and contribute to a more homogeneous pulp texture. Central composite design and surface response approach optimized wet foams with 50% leek pulp and varying proportions of egg white, maltodextrin, and carboxymethyl cellulose based on foam qualities. Foaming agents were whipped with a hand mixer for 3 min under optimum foaming conditions (8.93% egg white, 14.37% maltodextrin, and 1.50% CMC), and then leek pulp was added and whipped for another 3 min. The obtained foam pulp mixture was spread on trays at a thickness of 0.5 cm and dried by both freeze-drying and convective drying methods. Drying of foam pulp mixture Samples were freeze-dried for 48 h in a Labconco Freezone 12 Plus lyophilizer at −80 °C and 13 Pa.s. For the drying system, a laboratory-scale cabinet dryer was employed (EKSIS, Turkey). The drying process was carried out at 50 °C and 70 °C with an air speed of 0.5 m/s. The dried samples were then ground into powder using a Sinbo SCM 2934 grinder. Physicochemical analysis of the dried powders The color characteristics, pH, and dry matter of the dried powders were assessed. As for the color analysis, the L* (lightness/darkness), a* (redness/greenness), and b* (yellowness/blueness) values were measured using a colorimeter. Foam expansion, density, and stability To assess foam expansion, a 50 g foam sample was placed in suitable graduated cylinders, and its volume was recorded. The foam’s percentage expansion was computed as follows:\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:\mathrm{F}\mathrm{o}\mathrm{a}\mathrm{m}\:\mathrm{E}\mathrm{x}\mathrm{p}\mathrm{a}\mathrm{n}\mathrm{s}\mathrm{i}\mathrm{o}\mathrm{n}\:\left({\%}\right)=\frac{{V}_{after\:expansion}-{V}_{inittial\:volume}}{{V}_{inittial\:volume}}\:\times\:100$$\end{document} The prepared foam was promptly transferred into a suitable graduated cylinder without compromising its structure, and the density was subsequently measured. The foam density was calculated using the following equation 2:\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:\mathrm{F}\mathrm{o}\mathrm{a}\mathrm{m}\:\mathrm{D}\mathrm{e}\mathrm{n}\mathrm{s}\mathrm{i}\mathrm{t}\mathrm{y}\left(\frac{\mathrm{g}}{{cm}^{3}}\right)=\frac{{Mass\:of\:foam}_{g}}{{Volume\:of\:foam\:}_{{cm}^{3}}}$$\end{document} To assess foam stability, the prepared foam was allowed to rest for three hours, and the stability was determined using the subsequent equation 226:\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:\mathrm{F}\mathrm{o}\mathrm{a}\mathrm{m}\:\mathrm{s}\mathrm{t}\mathrm{a}\mathrm{b}\mathrm{i}\mathrm{l}\mathrm{i}\mathrm{t}\mathrm{y}\left(\mathrm{\%}\right)=\frac{{V}_{final\:volume\:\left(mL\right)}}{{V\:}_{\:initial\:volume\:\left(mL\right)}}\times\:100$$\end{document} Determination of total flavonoids 1 mL of the sample was combined with 0.3 mL of 5% w/v NaNO₂. After 5 min, 0.5 milliliters of 2% w/v AlCl₃ were added. The mixture was, then, neutralized with 0.5 mL of a 1 mol/L NaOH solution after 6 min. The mixture was maintained at room temperature for 10 min, after which absorbance was assessed at 510 nm27. Assessment of total phenolic content (TPC) The TPC analysis was conducted utilizing the Folin-Ciocalteu method28. In this procedure, 150 µL of the diluted sample was mixed with 750 µL of 10% Folin-Ciocalteu reagent, and after a 5-min interval, 600 µL of 7.5% sodium carbonate (Na₂CO₃) was incorporated. The absorbance of the mixture was measured at 760 nm via a UV spectrophotometer (Thermo Spectronic) after being incubated in the dark for 2 h. The total phenolic content (TPC) was reported as mg gallic acid equivalent (mg GAE/g) per gram. Determination of volatile components The volatile compounds were identified using a gas chromatography mass spectrometer (GC-MS). In a 20 mL vial, 1 g of powdered samples was weighed and combined with 1.5 mL of pure water for sample preparation. The syringe was immersed in the vial and kept in a water bath at 55–60 °C for 60 min. After 60 min, it was transferred to the GC-MS apparatus (Shimadzu Corporation, Kyoto, Japan). The MS library was used to determine the volatile components. Determination of individual phenolic compounds The powder sample extracts were transferred to vials after passing through a 0.45 μm syringe filter. An LC-MS/MS system from Thermo Scientific identified each phenolic compound. The instrument parameters included a binary gradient of solvent A (water with 0.1% formic acid) and solvent B (methanol). The solvent flow rate was maintained at 0.7 mL/min, and the column oven temperature was set to 30 °C. The column used was an ODS HYPERSIL with dimensions 4.6 × 250 mm and a particle size of 5 μm. The injection volume was 20 µL, and the total analysis time was 34 min. The MS/MS instrument was operated with a capillary temperature of 300 °C and a vaporizer temperature of 350 °C. The sheath gas pressure and auxiliary gas pressure were set to 30 and 13 psi, respectively. For positive mode operation, the spray voltage was 4000 V, while in negative mode, it was 2500 V. A discharge current of 4 µA was employed. Antioxidant activity The DPPH (1,1-diphenyl-2-picrylhydrazyl) radical scavenging activity was performed using a modified method28. 1 mL of DPPH solution (0.06 mM in 80% methanol) was mixed with 50 µL of the sample, and the mixture was shaken. It was then left to stand in the dark for 1 h until the reaction was completed. The absorbance was measured at 517 nm using a spectrophotometer (Thermo Spectronic). The DPPH radical scavenging activity for each extract was calculated using a calibration curve, with Trolox as the standard. The results were expressed as mmol Trolox equivalent (TE) per gram dry weight (dw). In FRAP analysis, a 50 µL sample was mixed with 950 mM FRAP solution containing 100 mM acetate buffer, 10 mM FeCl₃, and 10 mM 2,4,6-tripyridyl-s-triazine (TPTZ). The mixture was shaken for approximately 5 min, and the optical density was measured at 593 nm against a blank. FRAP values were expressed as mmol Trolox equivalents (TE) per gram dry weight (g⁻¹ DW). The FRAP values of the extracts were calculated by constructing a calibration curve using FeSO₄ as a standard. The results were expressed as mmol FeSO4 equivalents (mmol ISE g-1 dw)29. In the ABTS assay, a 2.45 mM aqueous solution of potassium persulfate was mixed with a 7 mM ABTS solution to generate ABTS. The ABTS was incubated in darkness for 12 h. Subsequently, 10 µl of samples were combined with 1 mL of working solution in a vessel and vortexed for 1 min. The optical density was measured at 734 nm with a UV-vis spectrophotometer. Furthermore, the blank consisted of phosphate-buffered saline at a concentration of 5 mM. The results were expressed as mg TE/g, based on the Trolox standard curve30. Characterization of the dried powders The microstructure of the dried powders was determined using a scanning electron microscope (SEM, JEOL JSM-7001 F). A small amount of powder samples were placed on a double-sided stainless-steel stub and coated for 2 min at 10 nm with the help of an argon and plasma flow sputter coater. The obtained images were recorded at acceleration voltages of 10 kV and 15 kV31. An FTIR spectrometer was used to analyze the powder samples and get the spectra from 4000 to 800 cm⁻¹ (Perkin Elmer, Spectrum Two, USA, PEService 35). Response surface methodology experimental design The foam drying of leek pulp was determined using the Response Surface Methodology (RSM) for the suitable foaming agent, egg white (albumin), foam stabilizer carboxymethyl cellulose (CMC), and maltodextrin ratios. The central composite design (CCD), in which foam density (FD), foam volume (FE), and foam stability (FS) were taken as dependent variables, was carried out using Design-Expert 10.0 software (Stat-Ease Inc., USA). 20 experiments were performed at the central point with 6 replications. Three independent variables were evaluated at 5 coded levels, including − 1.68, − 1, 0, + 1, and + 1.68 (Table 1). The maltodextrin and egg white concentration varied from 1.59% at the lowest level (− 1.68) to 18.41% at the highest level (+ 1.68). The central point being 10.0%. CMC was tested at lower levels, ranging from 0.159% (− 1.68) to 1.84% (+ 1.68), with intermediate levels at 0.5%, 1.0%, and 1.5%. The experimental data that was fitted to the polynomial model is represented in the following equation: Table 1Experimental design used to determine the proportions of foaming agents.Independent variablesLevels−1.68−10+ 1+ 1.68Egg white, %1.595.010.015.018.41Maltodextrin, %1.595.010.015.018.41Carboxymethyl cellulose, %0.1590.51.01.51.84 \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:Y={\beta\:}_{0}+{\sum\:}_{n=1}^{3}{\beta\:}_{i}{X}_{i}+\sum\:_{i=-}^{3}{\beta\:}_{ii}{X}_{ii}+\:\sum\:_{i=1}^{2}\sum\:_{j=i+1}^{3}{\beta\:}_{ij}{X}_{i}{X}_{j}$$\end{document} Table 1Experimental design used to determine the proportions of foaming agents.Independent variablesLevels−1.68−10+ 1+ 1.68Egg white, %1.595.010.015.018.41Maltodextrin, %1.595.010.015.018.41Carboxymethyl cellulose, %0.1590.51.01.51.84 Experimental design used to determine the proportions of foaming agents. Y is the predicted response; Xi, Xj are coded independent factors, βi, βii and βij interactive, quadratic, and linear coefficients, respectively, and β is the model intercept. Drying kinetics The foamed pulp was dried in hot air (convective) at 50 and 70 °C with an air speed of 0.5 m/s. During drying, changes in the moisture content obtained during drying were recorded, and 13 different drying models were used in the mathematical modeling of moisture content (Table 2). Table 2Models used in drying Leek pulp.ModelModel nameModel equation (MR)References1Aghabashlo modelexp(-k.x/(1+g.x)) 32 2Appr. of Diffusiona.exp(-k.x) +(1-a).exp(-k.b.t) 33 3Henderson ve Pabisa·exp(-k·t) 34 4Logarithmica.exp(-kx) +b 35 5Logisticb/(1+a.exp (k.x)) 36 6Midillia.exp(-k.(xn)) + (b.x) 37 7Verma‘a.exp(-k.x^n)+(1-a).exp(-g.x^f)’ 38 8Newtonexp(-k.x) 39 9Pageexp(-k.xn) 40 10Two-terma.exp(-k.x) +b.exp(-g.x) 41 11Two-term exponentiala.exp(-k.x) +(1-a).exp(-k.a.x) 41 12Modified page‘exp(-k.x^n) +b’ 42 13Wang ve Singh1+(a.x) +b.x2 43 Table 2Models used in drying Leek pulp.ModelModel nameModel equation (MR)References1Aghabashlo modelexp(-k.x/(1+g.x)) 32 2Appr. of Diffusiona.exp(-k.x) +(1-a).exp(-k.b.t) 33 3Henderson ve Pabisa·exp(-k·t) 34 4Logarithmica.exp(-kx) +b 35 5Logisticb/(1+a.exp (k.x)) 36 6Midillia.exp(-k.(xn)) + (b.x) 37 7Verma‘a.exp(-k.x^n)+(1-a).exp(-g.x^f)’ 38 8Newtonexp(-k.x) 39 9Pageexp(-k.xn) 40 10Two-terma.exp(-k.x) +b.exp(-g.x) 41 11Two-term exponentiala.exp(-k.x) +(1-a).exp(-k.a.x) 41 12Modified page‘exp(-k.x^n) +b’ 42 13Wang ve Singh1+(a.x) +b.x2 43 Models used in drying Leek pulp. Statistical analysis The Design-Expert software 10.0 (Stat-Ease Inc., USA) was used to design the optimization process and to generate the models and 3D graphics. The ANOVA of response surface methodology was applied for the statistical significance. The coefficient of determination (R2), adjusted coefficient of determination (adj. R2), coefficient of variation (CV), and Fisher’s test value (F-value) were used for the validation of the models. The analyses were conducted in triplicate, and the results were presented as mean ± standard deviation (SD). The statistical significance level was accepted as p < 0.05. The optimum conditions were determined based on the desirability function. Other analyses were carried out in three replicates, the one-way ANOVA followed by a Duncan’s multiple range test (SPSS, version 22) was implemented to determine the effect of various drying conditions on the quality parameters of the obtained leek powder. Results Physicochemical analysis of fresh leek pulp Table 3 displays the results of the analyses conducted on fresh leek pulp. The analysis of leek color values revealed an L* value of 67.25 ± 1.37, an -a* value of 7.61 ± 0.42, and a + b* value of 31.23 ± 1.08. The phenolic content in fresh leek pulp was 526.41 ± 43.62 mg/kg, while the total flavonoid content was 96.53 ± 16.95 mg/kg. The antioxidant activity values were quantified as follows: DPPH 9.86 ± 3.93 mmol/g, FRAP 0.63 ± 0.01 mmol/g, and ABTS 91.35 ± 6.02 mmol/g. In test samples, the pH, dry matter, total soluble solids, and water activity (aw) were 6.51 ± 0.01, 12.64 ± 0.13%, 10.25 ± 0.35%, and 0.9961 ± 0.0001, respectively. Table 3Properties of leek pulp.ParametersValuesColor L*67.25 ± 1.37a*−7.61 ± 0.42b*31.23 ± 1.08pH6.51 ± 0.01DM (Dry matter), %12.64 ± 0.13TSS (Total soluble solids), %10.25 ± 0.35Water activity (aw)0.9961 ± 0.0001TPC, mg/kg526.41 ± 43.62TF, mg/kg96.53 ± 16.95DPPH, mmol/g9.86 ± 3.93FRAP, mmol/g0.63 ± 0.01ABTS, mmol/g91.35 ± 6.02 Table 3Properties of leek pulp.ParametersValuesColor L*67.25 ± 1.37a*−7.61 ± 0.42b*31.23 ± 1.08pH6.51 ± 0.01DM (Dry matter), %12.64 ± 0.13TSS (Total soluble solids), %10.25 ± 0.35Water activity (aw)0.9961 ± 0.0001TPC, mg/kg526.41 ± 43.62TF, mg/kg96.53 ± 16.95DPPH, mmol/g9.86 ± 3.93FRAP, mmol/g0.63 ± 0.01ABTS, mmol/g91.35 ± 6.02 Properties of leek pulp. Optimizing foam production The design plan and responses, totaling twenty trial points, are presented in Table 4. The lowest foam density was found with 10% egg white, 1.59104% maltodextrin, and 1% CMC (No. 2), whereas the highest value was obtained with 15% egg white, 15% maltodextrin, and 0.5% CMC (No. 15). Three different conditions were determined for the lowest foam expansion, including (1) 18.409% egg white, 10% maltodextrin, and 1% CMC; (2) 15% egg white, 15% maltodextrin, and 0.5% CMC; and (3) 1.59104% egg white, 10% maltodextrin, and 1% CMC; Nos. 10, 15, and 20. The condition of 10% egg white, 10% maltodextrin, and 1.8409% CMC (No. 7) provided the highest foam density. Furthermore, the lowest foam stability was determined at 10% egg white, 10% maltodextrin, and 0.159% CMC (No. 8). The combination of 10% egg white, 18.409% maltodextrin, and 1% CMC (No. 14) yielded the highest foam stability. Through these results, high stability and expansion and low foam density conditions were selected. All of the responses fit the model, according to our analysis of the collected data. The model has high significance (p < 0.0181) in terms of responses. Table 4Effect of foaming agents and stabilizers on foam properties.NoA: Egg white, %Independent variablesC: CMC, %FD, g/cm3Dependent variables*FS, %B: Maltodextrin, %FE, %15.005.000.500.4178.5066.00210.001.591.000.2978.5083.0035.0015.000.500.4153.5067.90410.0010.001.000.3278.5068.00515.005.000.500.4563.5064.00610.0010.001.000.3768.5072.00710.0010.001.840.4098.5098.00810.0010.000.160.5253.5049.00910.0010.001.000.3973.5065.001018.4110.001.000.5048.5059.001110.0010.001.000.4258.5067.301210.0010.001.000.3968.5077.001315.0015.001.500.4663.5099.001410.0018.411.000.4173.50100.001515.0015.000.500.5948.5057.001615.005.001.500.3468.5073.00175.005.001.500.3473.5076.001810.0010.001.000.4168.5069.00195.0015.001.500.4473.5099.00201.5910.001.000.4148.5071.00*Foam density (FD) Foam expansion (FE) Foam stability (FS). Table 4Effect of foaming agents and stabilizers on foam properties.NoA: Egg white, %Independent variablesC: CMC, %FD, g/cm3Dependent variables*FS, %B: Maltodextrin, %FE, %15.005.000.500.4178.5066.00210.001.591.000.2978.5083.0035.0015.000.500.4153.5067.90410.0010.001.000.3278.5068.00515.005.000.500.4563.5064.00610.0010.001.000.3768.5072.00710.0010.001.840.4098.5098.00810.0010.000.160.5253.5049.00910.0010.001.000.3973.5065.001018.4110.001.000.5048.5059.001110.0010.001.000.4258.5067.301210.0010.001.000.3968.5077.001315.0015.001.500.4663.5099.001410.0018.411.000.4173.50100.001515.0015.000.500.5948.5057.001615.005.001.500.3468.5073.00175.005.001.500.3473.5076.001810.0010.001.000.4168.5069.00195.0015.001.500.4473.5099.00201.5910.001.000.4148.5071.00*Foam density (FD) Foam expansion (FE) Foam stability (FS). Effect of foaming agents and stabilizers on foam properties. *Foam density (FD) Foam expansion (FE) Foam stability (FS). Table 5 demonstrates that the ratios of egg white, maltodextrin, and CMC significantly influenced foam density and stability (p < 0.05). The ratios of egg white and CMC influenced foam density, while the ratios of maltodextrin and CMC affected foam stability. Egg white exhibited a quadratic influence on density, expansion, and stability; the CMC ratio impacted density, while maltodextrin affected stability (p < 0.01). The values for R2, corrected R2, and estimated R2 were determined as follows: (1) foam density, 0.9071, 0.8234, and 0.6862; (2) foam expansion, 0.7895, 0.6000, and − 0.1687; and (3) for foam stability, 0.9617, 0.9273, and 0.8364, respectively. Table 5ANOVA results of foam density, expansion, and stability.SourceDensity, g/cm3Expansion, %Stability, %SSF valuep valueSSF valuep valueSSF valuep valueModel0.083710.850.00042411.784.170.01813978.8227.93< 0.0001A-Egg White, %0.011213.080.004789.701.390.265095.336.020.0340B-Maltodextrin, %0.023126.960.0004208.873.250.1017384.7824.310.0006C- CMC, %0.017019.830.0012897.0013.950.00392229.87140.88< 0.0001AB0.00323.730.08223.120.04860.83004.350.27490.6115AC0.00505.830.03643.120.04860.830012.250.77400.3996BC0.00080.93320.3568153.122.380.1539365.8523.110.0007A²0.010211.900.0062841.5013.080.004761.053.860.0779B²0.00161.860.202662.430.97050.3478770.3048.67< 0.0001C²0.011613.530.004362.430.97050.347812.930.81660.3874Residual0.0086643.22158.28Lack of Fit0.00220.35360.8607422.381.910.246968.470.76240.6134Pure Error0.0063220.8389.81Cor Total0.09233055.004137.10R²0.90710.78950.9617Adjusted R²0.82340.60000.9273Predicted R²0.6862−0.16870.8364Adeq Precision13.69168.012618.4852% C.V.7.0811.975.38 Table 5ANOVA results of foam density, expansion, and stability.SourceDensity, g/cm3Expansion, %Stability, %SSF valuep valueSSF valuep valueSSF valuep valueModel0.083710.850.00042411.784.170.01813978.8227.93< 0.0001A-Egg White, %0.011213.080.004789.701.390.265095.336.020.0340B-Maltodextrin, %0.023126.960.0004208.873.250.1017384.7824.310.0006C- CMC, %0.017019.830.0012897.0013.950.00392229.87140.88< 0.0001AB0.00323.730.08223.120.04860.83004.350.27490.6115AC0.00505.830.03643.120.04860.830012.250.77400.3996BC0.00080.93320.3568153.122.380.1539365.8523.110.0007A²0.010211.900.0062841.5013.080.004761.053.860.0779B²0.00161.860.202662.430.97050.3478770.3048.67< 0.0001C²0.011613.530.004362.430.97050.347812.930.81660.3874Residual0.0086643.22158.28Lack of Fit0.00220.35360.8607422.381.910.246968.470.76240.6134Pure Error0.0063220.8389.81Cor Total0.09233055.004137.10R²0.90710.78950.9617Adjusted R²0.82340.60000.9273Predicted R²0.6862−0.16870.8364Adeq Precision13.69168.012618.4852% C.V.7.0811.975.38 ANOVA results of foam density, expansion, and stability. Table 6 displays regression equations based on statistics for the second-order polynomial using actual variables, while Table 6 shows the optimal parameter values according to the desirability function. The desirability function yielded 48 distinct points that provided optimal conditions. The highest and optimum desirability values from the program were used for analysis. The composition consisted of 8.93% egg white, 14.37% maltodextrin, and 1.50% carboxymethyl cellulose. Foam density was estimated at 0.41 g/cm³, expansion at 81.51%, and stability at 100% under these conditions. Upon validation of the estimated points, foam density was established at 0.41 ± 0.03 g/cm³, foam expansion at 145.95 ± 11.09%, and foam stability at 95.32 ± 0.95%. Table 6Formulas obtained from experimental data for volume, density, and stability.ParametersFormulasDensity= 0.3831 + 0.0287 A + 0.0411B-0.0353 C + 0.0200AB-0.0250AC + 0.0100BC + 0.0266 A²−0.0105B²+0.0284 C²Expansion= 74.69841 + 5.10059 A-4.44718B-20.44144 C + 0.025000AB + 0.250000AC + 1.75000BC-0.305657 A²+0.083251B²+8.32512 C²Stability= 69.78–2.64 A + 5.31B + 12.78 C-0.7375AB + 1.24AC + 6.76BC-2.06 A²+7.31B²+0.9471 C²A; Egg White %. B; Maltodextrin %. C; Carboxymethyl Cellulose %. Table 6Formulas obtained from experimental data for volume, density, and stability.ParametersFormulasDensity= 0.3831 + 0.0287 A + 0.0411B-0.0353 C + 0.0200AB-0.0250AC + 0.0100BC + 0.0266 A²−0.0105B²+0.0284 C²Expansion= 74.69841 + 5.10059 A-4.44718B-20.44144 C + 0.025000AB + 0.250000AC + 1.75000BC-0.305657 A²+0.083251B²+8.32512 C²Stability= 69.78–2.64 A + 5.31B + 12.78 C-0.7375AB + 1.24AC + 6.76BC-2.06 A²+7.31B²+0.9471 C²A; Egg White %. B; Maltodextrin %. C; Carboxymethyl Cellulose %. Formulas obtained from experimental data for volume, density, and stability. A; Egg White %. B; Maltodextrin %. C; Carboxymethyl Cellulose %. Drying kinetics The drying parameters of leek powder, dehydrated at 50 °C and 70 °C via the foam drying technique, were ascertained through the equations derived from the models in Table 2. Figure 1 shows the moisture ratio (MR)–time curves at 50 °C and 70 °C, whereas Table 7 presents the outcomes of these models. The moisture ratio (MR) decreased faster at 70 °C than at 50 °C, as shown in Fig. 1. A high R² value signifies the model that most accurately represents the experimental data. The Midilli model, which yielded the highest R² values, was deemed the most appropriate drying model for this study. The R² values were calculated as 0.998793 for 50 °C and 0.999493 for 70 °C.Fig. 1(a) Response surface plots and contour curves showing the effect of carboxymethyl cellulose and egg white on density; (b) Response surface plots and contour curves demonstrating the effect of carboxymethyl cellulose and maltodextrin on stability. (a) Response surface plots and contour curves showing the effect of carboxymethyl cellulose and egg white on density; (b) Response surface plots and contour curves demonstrating the effect of carboxymethyl cellulose and maltodextrin on stability. Table 7Statistical parameters of powders dried at 50 °C and 70 °C.Model nameDrying temperature (°C)Statistical parametersR2RMSEX2Newton500.9973790.0132010.000174700.9476740.0668720.004472Page500.9980000.0118010.000139700.9869470.0347640.001209‘Modified page’500.9980000.0118010.000139700.9990880.0095990.000009‘Henderson ve Pabis’500.9976290.0128500.000165700.9947170.0221170.000489‘Logarithmic’500.9976670.0130590.000171700.9947200.0230940.000533‘Two-term’500.9981810.0118320.000140700.9838920.0423040.001790‘Two-term exponential’500.9973260.0136450.000186700.9919390.0273190.000746‘Wang ve Singh’500.9994740.0060480.000003700.9717830.0511120.002612‘Approx. of Diffusion’500.9975550.0137180.000188700.9946810.0243100.000591‘Verma’500.9977460.0128370.000165700.9476730.0726990.005285‘Logistic’500.9979600.0122110.000149700.9378480.0792300.006277‘Midilli’500.9987930.0096370.000009700.9994930.0075030.000005‘Aghabashlo model’500.9977610.0124850.000156700.9711360.0516950.002672 Table 7Statistical parameters of powders dried at 50 °C and 70 °C.Model nameDrying temperature (°C)Statistical parametersR2RMSEX2Newton500.9973790.0132010.000174700.9476740.0668720.004472Page500.9980000.0118010.000139700.9869470.0347640.001209‘Modified page’500.9980000.0118010.000139700.9990880.0095990.000009‘Henderson ve Pabis’500.9976290.0128500.000165700.9947170.0221170.000489‘Logarithmic’500.9976670.0130590.000171700.9947200.0230940.000533‘Two-term’500.9981810.0118320.000140700.9838920.0423040.001790‘Two-term exponential’500.9973260.0136450.000186700.9919390.0273190.000746‘Wang ve Singh’500.9994740.0060480.000003700.9717830.0511120.002612‘Approx. of Diffusion’500.9975550.0137180.000188700.9946810.0243100.000591‘Verma’500.9977460.0128370.000165700.9476730.0726990.005285‘Logistic’500.9979600.0122110.000149700.9378480.0792300.006277‘Midilli’500.9987930.0096370.000009700.9994930.0075030.000005‘Aghabashlo model’500.9977610.0124850.000156700.9711360.0516950.002672 Statistical parameters of powders dried at 50 °C and 70 °C. Physical analyses of powder samples Table 8 presents the color, dry matter, and pH values of the powder samples. The color parameters, dry matter content, and pH of the desiccated powders fluctuated based on the drying technique employed. The lyophilized sample exhibited the highest brightness, with a lightness (L*) value of 89.64, surpassing the samples dried at 50 °C (86.94) and 70 °C (85.51). Redness (a*) escalated with drying temperature, rising from 0.38 in the lyophilized powder to 2.31 and 2.81 at 50 °C and 70 °C, respectively. A comparable trend was noted for yellowness (b*), increasing from 8.79 (lyophilized) to 12.08 (50 °C) and attaining 15.69 at 70 °C. The lyophilized sample exhibited the highest dry matter content at 94.46%, whereas hot air drying at 50 °C and 70 °C yielded slightly lower values of 91.96% and 92.48%, respectively. The pH values exhibited slight variation, with the lyophilized sample measuring 5.01 and the hot air-dried samples ranging from 4.92 to 4.96. Table 8Color characteristics, pH, and dry matter of the dried powder.L*a*b*Dry matter, %pHLyophilize89.64 ± 0.81a0.38 ± 0.23c8.79 ± 0.85c94.46 ± 0.095.01 ± 0.0350 °C86.94 ± 0.34b2.31 ± 0.06a12.08 ± 0.10b91.96 ± 0.064.92 ± 0.0470 °C85.51 ± 0.01b2.81 ± 0.02a15.69 ± 0.11a92.48 ± 1.984.96 ± 0.03*There is no statistically significant difference between the means marked with the same letter in the same column (p > 0.05). Table 8Color characteristics, pH, and dry matter of the dried powder.L*a*b*Dry matter, %pHLyophilize89.64 ± 0.81a0.38 ± 0.23c8.79 ± 0.85c94.46 ± 0.095.01 ± 0.0350 °C86.94 ± 0.34b2.31 ± 0.06a12.08 ± 0.10b91.96 ± 0.064.92 ± 0.0470 °C85.51 ± 0.01b2.81 ± 0.02a15.69 ± 0.11a92.48 ± 1.984.96 ± 0.03*There is no statistically significant difference between the means marked with the same letter in the same column (p > 0.05). Color characteristics, pH, and dry matter of the dried powder. *There is no statistically significant difference between the means marked with the same letter in the same column (p > 0.05). Table 9 delineates the bulk and tapped densities, solubility, Carr index, and Hausner ratio (HR) solubility values for powders produced via lyophilization, 50 °C drying, and 70 °C drying. The results showed that lyophilized powder had the lowest bulk and tapped density (0.49 ± 0.02 and 0.68 ± 0.01), while 70 °C dried powder had the highest values (0.60 ± 0.03 and 0.79 ± 0.01). In terms of solubility, the lyophilized powder exhibited a value of 90.36 ± 6.07, while the powder dried at 50 °C demonstrated a value of 78.65 ± 5.58. Additionally, the powder dried at 70 °C showed a solubility of 85.76 ± 9.81. Table 9Bulk and tapped densities, solubility, Carr index, and Hausner ratio results of the powders.Bulk densityTapped densitySolubilityCarr indexHRLyophilize0.49 ± 0.02b0.68 ± 0.01b90.36 ± 6.0728.85 ± 3.09a1.41 ± 0.0650 °C0.56 ± 0.01ab0.69 ± 0.01b78.65 ± 5.5818.93 ± 0.72b1.23 ± 0.0170 °C0.60 ± 0.03a0.79 ± 0.01a85.76 ± 9.8123.80 ± 2.51ab1.31 ± 0.04There is no statistically significant difference between the means marked with the same letter in the same column (p > 0.05). Table 9Bulk and tapped densities, solubility, Carr index, and Hausner ratio results of the powders.Bulk densityTapped densitySolubilityCarr indexHRLyophilize0.49 ± 0.02b0.68 ± 0.01b90.36 ± 6.0728.85 ± 3.09a1.41 ± 0.0650 °C0.56 ± 0.01ab0.69 ± 0.01b78.65 ± 5.5818.93 ± 0.72b1.23 ± 0.0170 °C0.60 ± 0.03a0.79 ± 0.01a85.76 ± 9.8123.80 ± 2.51ab1.31 ± 0.04There is no statistically significant difference between the means marked with the same letter in the same column (p > 0.05). Bulk and tapped densities, solubility, Carr index, and Hausner ratio results of the powders. There is no statistically significant difference between the means marked with the same letter in the same column (p > 0.05). Determination of individual phenolic compounds The analysis via LC-MS/MS identified four individual phenolic compounds in fresh leeks. Sinapic acid and cinnamic acid, commonly found in fresh vegetables, were the most abundant compounds. In addition, the powders’ specific phenolic profiles were examined using LC-MS/MS, and the results are presented in Table 10. In the foam-dried leek powder samples, the most common phenolic compound at 50 °C was sinapic acid (96.10 µg/100 g), and at 70 °C it was cinnamic acid (58.50 µg/100 g), while in the freeze-dried powder samples, sinapic acid was also the most common compound (50.40 µg/100 g). Table 10Distribution of phenolic compounds in powders (µg/100 g).Phenolic compoundsLyophilized50 °C70 °CPulpGallic acid29.6045.10-0.72Gentisic acid-6.40--Vanillin--9.900.12Syringaldehyde -1.60--Taxifolin5.10---Coumaric acid-5.3030.10-Sinapic acid50.4096.10-11.91Cinnamic acid--58.503.17Naringenin--0.30-Chlorogenic acid40.00-28.30- Table 10Distribution of phenolic compounds in powders (µg/100 g).Phenolic compoundsLyophilized50 °C70 °CPulpGallic acid29.6045.10-0.72Gentisic acid-6.40--Vanillin--9.900.12Syringaldehyde -1.60--Taxifolin5.10---Coumaric acid-5.3030.10-Sinapic acid50.4096.10-11.91Cinnamic acid--58.503.17Naringenin--0.30-Chlorogenic acid40.00-28.30- Distribution of phenolic compounds in powders (µg/100 g). Antioxidant properties of powders The antioxidant activity of leek powders that were subjected to three drying methods is illustrated in Table 11. The results indicate that the TPC and TF values remained relatively consistent across treatments, with no statistically significant differences (p > 0.05). Notable variation was detected in antioxidant assays: ABTS activity peaked at 70 °C (16.18 ± 0.30 mM/g) and reached its nadir at 50 °C (8.58 ± 1.80 mM/g). The DPPH radical scavenging activity increased with temperature, rising from 1.91 ± 0.53 mM/g in lyophilized samples to 4.56 ± 1.07 mM/g at 70 °C. In FRAP, values varied from 1.04 to 1.32 mM/g, exhibiting a modest increase at 70 °C. Table 11Antioxidant activity, total phenolic content, and flavonoid amount results.TPC, mg/kgTF, mg/kgABTS, mmol/gDPPH, mmol/gFRAP, mmol/gLyophilized1349.83 ± 222.13ab225.61 ± 4.76a13.83 ± 1.81ab1.91 ± 0.53c1.27 ± 0.26ab50 °C1340.31 ± 195.20b208.78 ± 66.67b8.58 ± 1.80b3.43 ± 1.60b1.04 ± 0.14b70 °C1368.87 ± 114.43a225.61 ± 4.76a16.18 ± 0.30a4.56 ± 1.07a1.32 ± 0.00a*There is no statistically significant difference between the means marked with the same letter in the same column (p > 0.05). Table 11Antioxidant activity, total phenolic content, and flavonoid amount results.TPC, mg/kgTF, mg/kgABTS, mmol/gDPPH, mmol/gFRAP, mmol/gLyophilized1349.83 ± 222.13ab225.61 ± 4.76a13.83 ± 1.81ab1.91 ± 0.53c1.27 ± 0.26ab50 °C1340.31 ± 195.20b208.78 ± 66.67b8.58 ± 1.80b3.43 ± 1.60b1.04 ± 0.14b70 °C1368.87 ± 114.43a225.61 ± 4.76a16.18 ± 0.30a4.56 ± 1.07a1.32 ± 0.00a*There is no statistically significant difference between the means marked with the same letter in the same column (p > 0.05). Antioxidant activity, total phenolic content, and flavonoid amount results. *There is no statistically significant difference between the means marked with the same letter in the same column (p > 0.05). Characterization of the dried powders Powders that were dried at a temperature of 70 degrees Celsius exhibited a more uniform morphological structure, as demonstrated in Fig. 2, which clearly demonstrates that the porosity decreased as the temperature increased. Moreover, as seen in Fig. 2, the pores in the morphological structure are voids created by air bubbles during foaming and preserved throughout the drying process.Fig. 2MR₀ – time curve. MR₀ – time curve. In Fig. 3, the spectra have three main regions: 3600–2900 cm⁻¹, 1700–1100 cm⁻¹, and 1150–800 cm⁻¹. The region 1 area is typically linked to hydroxyl (OH) stretching vibrations and is affected by the strength of hydrogen bonding. Additionally, various peaks in the 1300–1700 cm⁻¹ range of region 2 indicate the presence of amide I and II bending vibrations. The wide peak seen between 3600 and 3000 cm⁻¹ is linked to the stretching movements of –OH hydroxyl groups found in water molecules, phenolic compounds, carbohydrates, and organic acids.Fig. 3A scanning electron microscope image of dried samples: (a) 50 °C, (b) 70 °C, (c) Control (only lyophilized foam), and (d) Fresh Leek. A scanning electron microscope image of dried samples: (a) 50 °C, (b) 70 °C, (c) Control (only lyophilized foam), and (d) Fresh Leek. Discussion Physicochemical analysis of fresh Leek pulp The pH of the fresh leeks was 6.51. A significant pH drop was observed in 50 °C dried powder, whereas pH changes in lyophilized powder were the lowest among the three drying methods. A high proportion of white components in utilized samples, resulting in a marked change in an L* value in the color analysis compared to other leek studies documented in the literature. The changes in the color values were observed between three drying methods. An increase in drying temperature resulted in a slight decrease in lightness (L*) and an increased a* value. Biernacka et al.44 conducted a study on the white and the green parts of leek using freeze-drying; the color parameters (L*, a*, b*) were reported as 85.04, −3.09, 21.44, and 73.58, −8.96, and 29.05, respectively. As expected, fresh leeks showed a higher capacity of antioxidant activity than the dehydrated samples. Conversely, in foam mat drying samples, TPC and TF were found to be significantly high. The total phenolic content was 526.41 mg kg− 1 in the fresh leeks and 1353 mg kg⁻¹ in the dried samples. According to Čeryová (2024), the total polyphenol content in the white parts ranged from 446.30 to 1580.55 mg GAE/kg, whereas in green parts it was 748.09 to 2172.78 mg GAE/kg DM3245. As in Table 3, the highest antioxidant activity was found for fresh leeks. Consistent with the findings of this results, temperature significantly influenced heat-sensitive compounds, which resulted in significant losses in physicochemical properties and alterations in color46,33. Optimizing foam production Overall, R² and corrected R² expressions range between 0 and 1. The fact that these expressions are close to 1 and to each other means that the model is suitable. The data observed in the dependent variables demonstrated suitability for the model. The coefficient of variation (%C.V.) shows how much the model’s estimate varies and compares the model’s consistency to the average value. The fact that the coefficient of variation is 10% or lower provides information about the reliability of the data. In the study, it was observed that the coefficient of variation of the foam density and stability was 7.08 and 5.38, respectively, while the foam volume was above this limit at 11.97. Figure 4 presents the graph that illustrates the impact of independent variables on foam density and foam stability. As seen in Fig. 4a, the interaction of egg white and CMC ratios had a significant effect on density. As egg white increased, the density first decreased and then increased. The density rose as the CMC ratio dropped. As seen in Fig. 4b, as the maltodextrin and CMC ratio increased, foam stability increased.Fig. 4FTIR spectra of 50 °C, 70 °C, control (only lyophilized foam), and fresh leek samples. FTIR spectra of 50 °C, 70 °C, control (only lyophilized foam), and fresh leek samples. The optimization study revealed that, aside from expansion, the program’s predicted values closely aligned with the experimentally obtained values. Consequently, the response surface methodology is a reliable and reproducible tool for determining the agent ratio in the foam drying process. A wide range of foods have been the subject of optimization research thus far. In a study about drying peaches with foam, researchers used Response Surface Methodology (RSM) to find the best conditions, and the results showed that the amount of foaming agents greatly influenced the drying process47. The foam drying study on shrimp and papaya recorded foam densities ranging from 0.47 to 0.61 and 52 to 65 g/cm³, respectively48,49. In the yogurt study, methyl cellulose and egg white were employed in varying proportions. The sample that contained 4% egg white exhibited the highest foam expansion, which was 70.0%50. Drying kinetics The drying kinetics were modeled using thirteen thin-layer drying models, and the results demonstrated a strong temperature-dependent behavior. As shown in Table 7, the Midilli model provided the best fit for both temperatures with exceptionally high coefficients of determination (R² = 0.9988 at 50 °C and 0.9995 at 70 °C), indicating that moisture removal during foam-mat drying follows a combined diffusion-controlled and empirical exponential pattern. The increase in the drying rate constant (k) at 70 °C reflects the accelerated internal moisture diffusion and external mass transfer driven by higher thermal energy. Foam drying at appropriate foaming agent levels and temperature results in enhanced drying performance. The logarithmic and Midilli models effectively characterize the drying behavior, as evidenced by high R² values that signify strong predictive accuracy of moisture loss over time. Kadam and Balasubramanian (2011) identified 10% egg albumin as the optimal foaming agent for foam-dried tomato pulp at 60 °C, 65 °C, and 70 °C, and drying kinetics yielded the best R² value (0.985) for the logarithmic model51. In foam-dried mango pulp, a cabinet-type dryer at 60 °C was identified as the optimal temperature52. The Midilli model, exhibiting an R² value of 0.9945, most accurately characterized the drying process for assessing the adaptability of whey to foam drying. The moisture ratio was accurately predicted as a function of time and temperature, evidenced by a high coefficient of determination. Furthermore, it was concluded that the samples dried at 60 °C produced superior results relative to the other temperatures53. Physical analyses of powder samples As seen in Table 8, there was an increase in the b(+) (yellowness) value as temperature rose. The rise is attributed to the intensified Maillard reaction resulting from elevated temperatures and prolonged drying durations54. In the study by Biernacka et al., the color measurements (L*, a*, b*) for the white parts of freeze-dried leek samples were 85.04, −3.09, and 21.44, while the white parts of samples dried with hot air had measurements of 84.62, −1.24, and 17.35. Oxygen during hot air drying was found to oxidize the unsaturated pigments. Accordingly, it was determined that vacuum-drying or freeze-drying are better options for preserving pigment and color stability55. Studies indicate that maltodextrin positively influences color, whereas egg white powder can expedite the browning reaction. The foam’s structure may induce alterations in the resultant powder, presumably attributable to pigment segregation56. A study investigating the physicochemical properties of leeks dried using various techniques revealed that samples boiled in salt water and subsequently dried in a microwave, along with those dried in a tray dryer, yielded the highest pH value of 5.8457. For a powdered food to fulfill its nutritional purposes, its ingredients must be highly soluble58. Scientists who used foam drying to make acai powder found that emulsifier-containing samples were less dense and more soluble. The research highlighted that sustaining the emulsifier concentration beneath 0.7 could avert aggregation59. Powdered food flowability and stickiness are measured by the Carr index (CI) and Hausner ratio (HR). The Carr index demonstrated that the flowability value varied between 18% and 28%, with no notable difference detected across the temperatures. Nonetheless, the research conducted by Hajiaghaei and Sharifi categorized the samples dried at 50 °C as good according to the Carr index results, whereas it deemed those dried at 70 °C and through lyophilization as relatively good26. Determination of volatile compounds Volatile compounds in the samples were identified using GC-MS, as presented in Table 12. A total of 55, 50, and 70 volatile compounds were identified in the 50 °C, 70 °C, and freeze-dried powders, respectively. In the control group samples, 68 volatile compounds were identified, while 31 were identified in the fresh leek. It is important to note that the 70 °C dried samples contained 2,4-dimethylfuran, 2-furancarboxaldehyde (CAS), and furfural, which were not present at 50 °C. Furan compounds are generated through Maillard reactions and caramelization, both of which are affected by the presence of saccharides60. The evidence indicates that the powders dried at 50 °C are preferable. Table 12Volatile compound results (expressed as %) for powders dried at 50 °C, 70 °C, lyophilized powders, Leek pulp, and control (foam lyophilized without Leek).Volatile compoundsLyophilized50℃70℃ControlLeek pulpAldehydeAcetaldehyde (CAS) Ethanal0.2650.0350.045-0.1ALPHA. HEXYLCINNAMIC ALDEHYDE----0.0552- Heptenal, (Z)- (CAS) CIS-HEPT-2-ENAL0.2450.1850.52-0.2252- Hexenal, (E)- (CAS) (E)−2-Hexenal0.0850.03---2- Hexenal (CAS) 2-Hexen-1-al----0.032- Nonenal, (E)- (CAS) trans-2-Nonenal0.060.060.040.045-2- Pentenal, 2-methyl- (CAS) 2-Methyl-2-pentenal0.2250.075-0.040.23(+)−2-Aminoheptane----0.04Butanal, 3-methyl- (CAS) 3-Methylbutanal-0.01---Decanal (CAS) n-Decanal0.140.030.1150.480.05Heptanal (CAS) n-Heptanal-0.060.02--Hexanal (CAS) n-Hexanal0.10.090.060.0650.08Nonanal (CAS) n-Nonanal0.4850.5850.3650.9350.115Propanal (CAS) Propionaldehyde0.430.040.035-0.172- Heptenal, (Z)---0.040.03-2-Nonenal, (E)- (CAS) trans-2-Nonenal----0.092-Butenal, 2-methyl- (CAS) 2-FORMYL-2-BUTENE0.05---0.142-Nonenal, (E)----0.03-2-Butenal (CAS) Crotonaldehyde-----Butanal, 3-methyl- (CAS) 3-Methylbutanal--0.1--Benzeneacetaldehyde (CAS) Hyacinthin-----Lauric aldehyde---0.07-Undecanal---0.035- Acids Acetic acid (CAS) Ethylic acid-0.03---Carbamic acid, monoammonium salt (CAS) ammonium carbamate-0.091,2-Benzenedicarboxylic acid, diethyl ester (CAS) Ethyl phthalate0.0950.010.0650.110.052-Propynoic acid0.1450.3150.180.11-Decanoic acid (CAS) Capric acid-0.09---Pelargonic acid-0.16---1,1’-bibicyclo(2.2.2)octyl-4-carboxylic acid0.065--0.13-(Z)−3-Phenyl-2-propenoic acid, methyl ester-0.050.09-Acetic acid, fluoro-, ethyl ester (CAS) ethyl fluoroacetate0.21----3,4,6-trimethyl-4-hydroxyhept-5-enoic acid lactone0.175----2-Butenedioic acid (E)-, dibutyl ester (CAS) Fumaric Acid Di-N-Butyl Ester0.08-3-Pentenoic acid, 4-methyl- (CAS) Pyroterebic acid--0.02- Alcohol Methanethiol (CAS) Mercaptomethane-0.040.30.02-Myristic alcohol----0.051-Propanethiol0.0850.080.040.0950.022-Hexen-1-ol, (E)-----0.042-PROPEN-1-THIOL0.210.240.10.02-Capryl alcohol-0.0850.04--2-Octen-1-ol, (Z)- (CAS) cis-OCT-2-ENOL-0.010.19-0.1151-Nonanol (CAS) n-Nonyl alcohol0.080.060.070.03-Ethanol, 2-(dodecyloxy)- (CAS) DODECOXYETHANOL0.06--0.18Vinyl amyl carbinol0.31--1-Octanol (CAS) Octilin0.07-0.050.235-1-Pentanol (CAS) Amylol----0.021-Pentadecanol (CAS) Pentadecanol-0.13--1-Pentanol0.07----1-Butanol, 3-methyl- (impure) (CAS) 3-Methyl-1-butanol--0.055-Ethanol, 2-(dodecyloxy)-0.215--0.025-1-Tetradecanol (CAS) Alfol 140.07---0.071-Hexanol (CAS) n-Hexanol0.085----Cyclopentanol, 2-methyl- (CAS) 2-Methylcyclopentanol--0.03-Dihydromyrcenol---0.03-2-ETHYL HEXANOL---0.07Hexanol < n->---0.02Linalool---0.02Cyclohexanol, 5-methyl-2-(1-methylethyl)- (CAS) 3-p-Menthanol0.025Pelargol---0.051-Dodecanol (CAS) n-Dodecanol---0.2551-Tridecanol (CAS) n-Tridecanol---0.04 Esters 2-Butenedioic acid (Z)-, dibutyl ester (CAS) Dibutyl maleate0.8550.1550.141.491,2-Benzenedicarboxylic acid, bis(2-methylpropyl) ester (CAS) Isobutyl phthalate1.661.142-Propenoic acid, 3-phenyl-, methyl ester (CAS) Cinnamic acid methyl ester(Z)−3-Phenyl-2-Propenoıc Acıd, methyl ester0.050.09Acetic acid, fluoro-, ethyl ester (CAS) Ethyl fluoroacetate0.212-Butenedioic acid (E)-, dibutyl ester (CAS) Fumarıc Acıd Dı-N-Butyl Ester0.08Hexanedioic acid, dibutyl ester (CAS) Dibutyl adipate0.11----Methoxyacetic acid, dodecyl ester0.16---- Lactones 5,9-Undecadien-2-one, 6,10-dimethyl-, (E)- (CAS) (E)-Geranylacetone0.110.060.060.1150.13,4,6-Trimethyl-4-Hydroxyhept-5-Enoic Acid Lactone 0.175 Lactone0.175 Ketones 6-Methyl-5-hepten-2-one0.040.0350.030.162- Cyclopenten-1-one, 3-methyl- (CAS) 3-Methyl-2-cyclopentenone1-Octen-3-one (CAS) Vinyl amyl ketone0.082-Propanone (CAS) Acetone0.04----Cyclopentadecanone, 2-hydroxy----0.06Oxacycloheptadec-8-en-2-one---0.023 H-1,2-Dithiole-3-thione, 4-methyl- (CAS)---2-Nonanone (CAS) Methyl heptyl ketone---0.03 Alkanes Octadecane (CAS) n-Octadecane0.070.430.060.05Tetradecane (CAS) n-Tetradecane0.04Pentan-1,3-Dıoldıısobutyrate, 2,2,4-Trımethyl-0.15Propane, 1,1’-thiobis- (CAS) 4-Thiaheptane0.145Hexane < 2,3-dimercaptan->0.37Hexadecane0.07Cyclopropane, 1,1-Dibromo-2-Chloro-2-Fluoro- (CAS) 1,1-Dıbromo-2-Chloro-2-Fluorocyclopropane0.23Propane, 2,2-bis(methylthio)- (CAS) 2,2-Bıs(Methylmercapto)Propane0.14Dodecane (CAS) n-Dodecane0.0251,4,7,10,13,16-Hexaoxanonadecane, 18-propyl-0.51 Furans 2,4-Dimethylfuran0.032-Furancarboxaldehyde (CAS) Furfural0.060.09Furfural0.05 Sulfur Compounds Dimethyl sulfide0.030.02Thiirane, methyl- (CAS) Propylene sulfide0.390.170.10.185Disulfide, dimethyl0.030.0650.0250.03Methyl-trans-propenyl-disulfide0.4050.3350.3550.0850.47Disulfide < dipropyl->1.660.790.090.4856.375Trisulfide < dimethyl->0.230.420.770.080.545Disulfide, methyl 2-propenyl (CAS) Methyl allyl disulfide0.055Disulfide, 2-propenyl propyl (CAS) Allyl propyl disulfide0.210.11-0.060.67Allyl methyl trisulfide0.1450.210.285-0.425Trisulfide, dipropyl4.962.9651.68-8.545Trans-Propenyl Propyl Disulfide1.3150.890.6350.3953.295Diallyl disulphide-0.07-0.255Tetrasulfide, di-2-propenyl0.18---- Other Compounds TRANS-.BETA.-IONON-5,6-EPOXIDE-0.14--Thietane, 1-oxide0.3150.1550.105-0.063,4-Dimethylthiophene0.1250.160.07-Benzene, 1,4-dichloro- (CAS) p-Dichlorobenzene1.10.885-0.73Tetrasulfide, di-2-propenyl-0.19---Dithioallylpropionate-0.03---.Alpha-Triphenyl Acetate-0.05---3-Nonen-5-yne, 4-ethyl- (CAS)-0.13---3-Nonen-5-yne, 4-ethyl-, (Z)--0.07---Silane, trimethyl(1-methyldodecyloxy)-0.1550.0550.0650.08Thiophene, 2,4-dimethyl- (CAS) 2,4-Dimethylthiophene---0.04Diethyl Phthalate0.08-0.092-PROPEN-1-THIOL0.210.240.10.02Dimethyl 2,4-Dıketoglutarate13.5211.6058.195.26515.7921-KRONE-7-4.46---3-Nonen-5-yne, 4-ethyl- (CAS)-0.13---Thiophene, 2,4-dimethyl- (CAS) 2,4-Dimethylthiophene-0.26--1-P-MENTHEN-8-YL ACETATE---0.04-Undec-8-enal < cis->0.03--Phenol (CAS) Izal---0.155-Dec-2(E)-enal-----Limonene---0.03-Nonane, 1-chloro- (CAS) 1-Chlorononane---0.02-Nonane, 5-(2-methylpropyl)----0.02-Caproate < butyl->---0.035-Linalool---0.02-Oxirane, dodecyl----0.04-2-Nonenal, (E)----0.03-Eicosane (CAS) n-Eicosane---0.08-Isopropyl Myristate---0.08-Dihydrojasmonate < methyl->---0.05-4,8,12-Tetradecatrıenal, 5,9,13-Trımethyl----0.05-1,3,4,6,7,8-Hexahydro-4,6,6,7,8,8-Hexamethylcyclopenta(G)−2-Benzopyran0.05-Phenol, 2,4-bis(1,1-dimethylethyl) - (CAS) 2,4-Di-tert-butylphenol-0.04-Methane, tetranitro- (CAS) Tetranitromethane---0.12Isobutyl isothiocyanate---1.89 Table 12Volatile compound results (expressed as %) for powders dried at 50 °C, 70 °C, lyophilized powders, Leek pulp, and control (foam lyophilized without Leek).Volatile compoundsLyophilized50℃70℃ControlLeek pulpAldehydeAcetaldehyde (CAS) Ethanal0.2650.0350.045-0.1ALPHA. HEXYLCINNAMIC ALDEHYDE----0.0552- Heptenal, (Z)- (CAS) CIS-HEPT-2-ENAL0.2450.1850.52-0.2252- Hexenal, (E)- (CAS) (E)−2-Hexenal0.0850.03---2- Hexenal (CAS) 2-Hexen-1-al----0.032- Nonenal, (E)- (CAS) trans-2-Nonenal0.060.060.040.045-2- Pentenal, 2-methyl- (CAS) 2-Methyl-2-pentenal0.2250.075-0.040.23(+)−2-Aminoheptane----0.04Butanal, 3-methyl- (CAS) 3-Methylbutanal-0.01---Decanal (CAS) n-Decanal0.140.030.1150.480.05Heptanal (CAS) n-Heptanal-0.060.02--Hexanal (CAS) n-Hexanal0.10.090.060.0650.08Nonanal (CAS) n-Nonanal0.4850.5850.3650.9350.115Propanal (CAS) Propionaldehyde0.430.040.035-0.172- Heptenal, (Z)---0.040.03-2-Nonenal, (E)- (CAS) trans-2-Nonenal----0.092-Butenal, 2-methyl- (CAS) 2-FORMYL-2-BUTENE0.05---0.142-Nonenal, (E)----0.03-2-Butenal (CAS) Crotonaldehyde-----Butanal, 3-methyl- (CAS) 3-Methylbutanal--0.1--Benzeneacetaldehyde (CAS) Hyacinthin-----Lauric aldehyde---0.07-Undecanal---0.035- Acids Acetic acid (CAS) Ethylic acid-0.03---Carbamic acid, monoammonium salt (CAS) ammonium carbamate-0.091,2-Benzenedicarboxylic acid, diethyl ester (CAS) Ethyl phthalate0.0950.010.0650.110.052-Propynoic acid0.1450.3150.180.11-Decanoic acid (CAS) Capric acid-0.09---Pelargonic acid-0.16---1,1’-bibicyclo(2.2.2)octyl-4-carboxylic acid0.065--0.13-(Z)−3-Phenyl-2-propenoic acid, methyl ester-0.050.09-Acetic acid, fluoro-, ethyl ester (CAS) ethyl fluoroacetate0.21----3,4,6-trimethyl-4-hydroxyhept-5-enoic acid lactone0.175----2-Butenedioic acid (E)-, dibutyl ester (CAS) Fumaric Acid Di-N-Butyl Ester0.08-3-Pentenoic acid, 4-methyl- (CAS) Pyroterebic acid--0.02- Alcohol Methanethiol (CAS) Mercaptomethane-0.040.30.02-Myristic alcohol----0.051-Propanethiol0.0850.080.040.0950.022-Hexen-1-ol, (E)-----0.042-PROPEN-1-THIOL0.210.240.10.02-Capryl alcohol-0.0850.04--2-Octen-1-ol, (Z)- (CAS) cis-OCT-2-ENOL-0.010.19-0.1151-Nonanol (CAS) n-Nonyl alcohol0.080.060.070.03-Ethanol, 2-(dodecyloxy)- (CAS) DODECOXYETHANOL0.06--0.18Vinyl amyl carbinol0.31--1-Octanol (CAS) Octilin0.07-0.050.235-1-Pentanol (CAS) Amylol----0.021-Pentadecanol (CAS) Pentadecanol-0.13--1-Pentanol0.07----1-Butanol, 3-methyl- (impure) (CAS) 3-Methyl-1-butanol--0.055-Ethanol, 2-(dodecyloxy)-0.215--0.025-1-Tetradecanol (CAS) Alfol 140.07---0.071-Hexanol (CAS) n-Hexanol0.085----Cyclopentanol, 2-methyl- (CAS) 2-Methylcyclopentanol--0.03-Dihydromyrcenol---0.03-2-ETHYL HEXANOL---0.07Hexanol < n->---0.02Linalool---0.02Cyclohexanol, 5-methyl-2-(1-methylethyl)- (CAS) 3-p-Menthanol0.025Pelargol---0.051-Dodecanol (CAS) n-Dodecanol---0.2551-Tridecanol (CAS) n-Tridecanol---0.04 Esters 2-Butenedioic acid (Z)-, dibutyl ester (CAS) Dibutyl maleate0.8550.1550.141.491,2-Benzenedicarboxylic acid, bis(2-methylpropyl) ester (CAS) Isobutyl phthalate1.661.142-Propenoic acid, 3-phenyl-, methyl ester (CAS) Cinnamic acid methyl ester(Z)−3-Phenyl-2-Propenoıc Acıd, methyl ester0.050.09Acetic acid, fluoro-, ethyl ester (CAS) Ethyl fluoroacetate0.212-Butenedioic acid (E)-, dibutyl ester (CAS) Fumarıc Acıd Dı-N-Butyl Ester0.08Hexanedioic acid, dibutyl ester (CAS) Dibutyl adipate0.11----Methoxyacetic acid, dodecyl ester0.16---- Lactones 5,9-Undecadien-2-one, 6,10-dimethyl-, (E)- (CAS) (E)-Geranylacetone0.110.060.060.1150.13,4,6-Trimethyl-4-Hydroxyhept-5-Enoic Acid Lactone 0.175 Lactone0.175 Ketones 6-Methyl-5-hepten-2-one0.040.0350.030.162- Cyclopenten-1-one, 3-methyl- (CAS) 3-Methyl-2-cyclopentenone1-Octen-3-one (CAS) Vinyl amyl ketone0.082-Propanone (CAS) Acetone0.04----Cyclopentadecanone, 2-hydroxy----0.06Oxacycloheptadec-8-en-2-one---0.023 H-1,2-Dithiole-3-thione, 4-methyl- (CAS)---2-Nonanone (CAS) Methyl heptyl ketone---0.03 Alkanes Octadecane (CAS) n-Octadecane0.070.430.060.05Tetradecane (CAS) n-Tetradecane0.04Pentan-1,3-Dıoldıısobutyrate, 2,2,4-Trımethyl-0.15Propane, 1,1’-thiobis- (CAS) 4-Thiaheptane0.145Hexane < 2,3-dimercaptan->0.37Hexadecane0.07Cyclopropane, 1,1-Dibromo-2-Chloro-2-Fluoro- (CAS) 1,1-Dıbromo-2-Chloro-2-Fluorocyclopropane0.23Propane, 2,2-bis(methylthio)- (CAS) 2,2-Bıs(Methylmercapto)Propane0.14Dodecane (CAS) n-Dodecane0.0251,4,7,10,13,16-Hexaoxanonadecane, 18-propyl-0.51 Furans 2,4-Dimethylfuran0.032-Furancarboxaldehyde (CAS) Furfural0.060.09Furfural0.05 Sulfur Compounds Dimethyl sulfide0.030.02Thiirane, methyl- (CAS) Propylene sulfide0.390.170.10.185Disulfide, dimethyl0.030.0650.0250.03Methyl-trans-propenyl-disulfide0.4050.3350.3550.0850.47Disulfide < dipropyl->1.660.790.090.4856.375Trisulfide < dimethyl->0.230.420.770.080.545Disulfide, methyl 2-propenyl (CAS) Methyl allyl disulfide0.055Disulfide, 2-propenyl propyl (CAS) Allyl propyl disulfide0.210.11-0.060.67Allyl methyl trisulfide0.1450.210.285-0.425Trisulfide, dipropyl4.962.9651.68-8.545Trans-Propenyl Propyl Disulfide1.3150.890.6350.3953.295Diallyl disulphide-0.07-0.255Tetrasulfide, di-2-propenyl0.18---- Other Compounds TRANS-.BETA.-IONON-5,6-EPOXIDE-0.14--Thietane, 1-oxide0.3150.1550.105-0.063,4-Dimethylthiophene0.1250.160.07-Benzene, 1,4-dichloro- (CAS) p-Dichlorobenzene1.10.885-0.73Tetrasulfide, di-2-propenyl-0.19---Dithioallylpropionate-0.03---.Alpha-Triphenyl Acetate-0.05---3-Nonen-5-yne, 4-ethyl- (CAS)-0.13---3-Nonen-5-yne, 4-ethyl-, (Z)--0.07---Silane, trimethyl(1-methyldodecyloxy)-0.1550.0550.0650.08Thiophene, 2,4-dimethyl- (CAS) 2,4-Dimethylthiophene---0.04Diethyl Phthalate0.08-0.092-PROPEN-1-THIOL0.210.240.10.02Dimethyl 2,4-Dıketoglutarate13.5211.6058.195.26515.7921-KRONE-7-4.46---3-Nonen-5-yne, 4-ethyl- (CAS)-0.13---Thiophene, 2,4-dimethyl- (CAS) 2,4-Dimethylthiophene-0.26--1-P-MENTHEN-8-YL ACETATE---0.04-Undec-8-enal < cis->0.03--Phenol (CAS) Izal---0.155-Dec-2(E)-enal-----Limonene---0.03-Nonane, 1-chloro- (CAS) 1-Chlorononane---0.02-Nonane, 5-(2-methylpropyl)----0.02-Caproate < butyl->---0.035-Linalool---0.02-Oxirane, dodecyl----0.04-2-Nonenal, (E)----0.03-Eicosane (CAS) n-Eicosane---0.08-Isopropyl Myristate---0.08-Dihydrojasmonate < methyl->---0.05-4,8,12-Tetradecatrıenal, 5,9,13-Trımethyl----0.05-1,3,4,6,7,8-Hexahydro-4,6,6,7,8,8-Hexamethylcyclopenta(G)−2-Benzopyran0.05-Phenol, 2,4-bis(1,1-dimethylethyl) - (CAS) 2,4-Di-tert-butylphenol-0.04-Methane, tetranitro- (CAS) Tetranitromethane---0.12Isobutyl isothiocyanate---1.89 Volatile compound results (expressed as %) for powders dried at 50 °C, 70 °C, lyophilized powders, Leek pulp, and control (foam lyophilized without Leek). The powders dried at 50 °C displayed the highest variety of compounds among the samples. Notably, as the temperature increased, the convective dried samples showed a rise in alcohol content and a fall in acid number. Dipropyl trisulfide was found in both the convective and freeze-dried powders, which was anticipated since it is the main sulfur compound in leek pulp. However, in the control group, dipropyl disulfide was detected. Both compounds were present in elevated concentrations in leek pulp; however, their levels diminished with rising drying temperatures, resulting in an increase in trans-propenyl propyl disulfide. Consequently, they were comparatively preserved in the freeze-dried powders. In alignment with our study, the untreated leek sample revealed the presence of 7 aldehyde compounds, 2 sulfur compounds, 1 alcohol, and 1 ketone, as identified through headspace-solid phase microextraction-gas chromatography-mass spectrometry (HS-SPME-GC-MS)61. In general, saturated straight-chain aldehydes, like hexanal and heptanal, have unpleasant, spicy odors, whereas unsaturated aldehydes tend to smell fresh and grassy62. The alcohol and aldehyde levels in convectively dried leek samples were more varied than in fresh leek, possibly due to the breakdown or oxidation of other compounds at high temperatures. Moreover, the breakdown of plant cells could result in the emission of volatile compounds, or certain compounds could be produced through isomerization, degradation, or reorganization processes62. Aldehydes like heptanal, hexanal, butanal, decanal, propanal, nonanal, and their related compounds were often found in the samples in different amounts. When comparing the volatile components of the powders to fresh leek, significant differences were observed. These include acids, alcohols, and esters, which were not detected in fresh leeks but were likely formed in the powders due to the effects of temperature and foaming agents. Determination of individual phenolic compounds Individual phenolic compounds in the samples were presented in Table 10. In one study on apple pomace, drying at 50 °C, 60 °C, 70 °C and 80 °C showed significant reductions in total phenolic and flavonoid contents and antioxidant capacity compared to fresh material — in particular, drying un-blanched pomace at temperatures above 60 °C caused marked reductions in individual compounds such as epicatechin and p-coumaric acid63. A separate study found that drying pears at 60 °C and 70 °C resulted in approximately a 40% decrease in both total phenolic compounds and antioxidant activity for each temperature64. A study examining the thermal stability of specific phenolic compounds indicated that exposure to 60 °C and 80 °C for 4 h led to a decrease of 15% in gallic acid and 25% in vanillic acid. Furthermore, at 100 °C, gallic acid, vanillic acid, and catechin exhibited reductions of 30%, 37%, and 32%, respectively65. In contrast to these results, a separate investigation of foam-dried mango demonstrated that the concentration of gallic acid and chlorogenic acid increased as the drying temperature was increased66. Based on these findings, it seems that the agents utilized in foam drying could enhance the preservation of phenolic compounds. A separate study analyzed the antioxidant and phenolic compound profile of leek by drying the white and green sections through various methods. The green portion of the leek was determined to possess a higher phenolic content than the white part. Besides that, p-coumaric acid in convectively dried samples was higher than in freeze-dried leeks and vacuum-dried samples44. It is important to note that vanillin and cinnamic acid were not found in the lyophilized and 50 °C-dried powders. This absence may be attributed to the binding of these compounds to cell-wall matrices, which requires higher thermal energy for their release. At 70 °C, the increased temperature likely aided in the breakdown of conjugated phenolic structures, leading to the detection of free cinnamic acid at a concentration of 58.50 µg/100 g. Similar temperature-dependent liberation of bound phenolics has been reported in convective drying studies44. Antioxidant properties of powders Significant differences in DPPH radical activity were observed between lyophilized and temperature-dried samples. Increased drying temperatures expedite non-enzymatic browning reactions, and certain reaction products may demonstrate antioxidant properties67. The Maillard reaction is a complex process occurring when proteins and carbohydrates interact, resulting in substances recognized for their antioxidant properties31. Conversely, samples dried at 50 °C demonstrated the lowest antioxidant activity by the FRAP method. After drying leeks in microwaves and tray dryers, researchers found that their total phenolic content decreased57. Characterization of the dried powders A study on shrimp powder production via foam drying revealed that elevated temperatures improved porosity and pore size distribution48. An irregular morphological structure consists of voids created by air bubbles during foaming, as shown in Fig. 2, which was also revealed in the foam drying process of peach fruit47. In foam drying processes, high concentrations of maltodextrin facilitate the development of smooth, spherical particle morphologies. This phenomenon is ascribed to maltodextrin’s capacity to form a soft and porous surface structure68. Reports indicate that single bonds with hydrogen are influenced within the range of 4000 to 2000 cm⁻¹, while triple bonds are affected between 2300 and 2200 cm⁻¹. Double bonds show influence in the range of 1950 to 1550 cm⁻¹, and single bonds are impacted from 1300 to 800 cm⁻¹69. Furthermore, several peaks within the 1300–1700 cm⁻¹ range correlate with the presence of protein31. The presence of protein in egg white, utilized as a foaming agent in the foam drying method, is thereby confirmed. The extensive peak identified in the 3600–3000 cm⁻¹ range is linked to the stretching vibrations of –OH hydroxyl groups and also signifies the N–H stretching vibrations of unbound amino acids70. Conclusions The feasibility of the foam drying technique for leek vegetables was examined in this study. Carboxymethyl cellulose, maltodextrin, and egg white were chosen as foam agents and stabilizers, with respective usage rates of 1.50%, 14.37%, and 8.39%. The foam had stability of 95.32 ± 0.95%, expansion of 145.95 ± 11.09%, and density of 40.86 ± 3.19 g/cm³. The properties of the foam facilitated the creation of superior-quality powder. The Midilli model was selected as the most appropriate drying model for this study after the drying kinetics parameters were examined. The results for antioxidant activity and total phenolic compounds indicated TPC values of 1340.31, 1368.87, and 1349.83 mg/kg; TF values of 208.78, 225.61, and 225.61 mg/kg; ABTS values of 8.58, 16.18, and 13.83 mmol/g; DPPH values of 3.43, 4.56, and 1.91 mmol/g; and FRAP values of 1.04, 1.32, and 1.27 mmol/g for the samples dried at 50 °C and 70 °C and those that were freeze-dried, respectively. The optimal drying temperature for the preservation of volatile and phenolic compounds was determined to be 50 °C.