Experiments and physical Investigation on the adsorption of methylene on activated carbon Authors: Souhail Mohammed Bouzgarrou, Hedi Jedli, Rym Hassani, Ehab Sabi, Afzal Husain Khan, Khalifa Slimi Published: 2025 ABSTRACT AbstractIn this study, activated carbon (AC) derived from olive waste was employed as an alternative adsorbent for the removal of methylene blue (MB) from aqueous solutions. The AC was characterized using FTIR, SEM, XRD and N₂ adsorption–desorption analyses. The pseudo-second-order kinetic model and the Langmuir adsorption isotherm provided a good fit to the experimental data at 298, 303, and 313 K. A multilayer adsorption model was applied to elucidate the adsorption mechanisms between the dye molecules and the adsorbent. The number of MB active sites (n) was greater than unity at all temperatures, indicating a vertical orientation of the adsorbed molecules. The number of active sites (Dm) showed only slight variation with temperature. The decrease in MB adsorption capacities (Qm) from 235.21 to 198.62 mg·g⁻1 over the temperature range of 298–313 K was primarily influenced by the n parameter. Adsorption energy analysis revealed that MB adsorption was exothermic and occurred via a physisorption process. This study provides valuable insights into the interactions between MB molecules and AC active sites.Keywords: Adsorption, Activated carbon, Methylene blue, Physical modelingSubject terms: Chemistry, Materials science Introduction Many industries generate effluents containing dyes during their manufacturing processes1. In particular, textile industries discharge significant amounts of dyes in their wastewater, which exhibit toxic effects on the environment and living organisms2. Various chemical and physical methods have been developed for dye removal, including coagulation, adsorption, membrane separation, and chemical oxidation3. Among these treatment techniques, adsorption is recognized as one of the most effective methods4. Numerous adsorbents have been tested for color removal from aqueous effluents, with activated carbon being the most widely used due to its excellent textural properties; however, its high production and regeneration costs limit its large-scale application5. Consequently, many researchers have explored the use of low-cost materials as carbon precursors for dye and wastewater treatment, such as corn cob6, Coriandrum sativum7, waste orange peels8, almond shells9, peach stones10, and pine wood11. In this context, activated carbon derived from olive waste was used to study the removal of methylene blue (MB) dye. Adsorption isotherms for MB on the activated carbon were measured at different temperatures (298, 308, and 318 K), and the adsorbent was thoroughly characterized. The main objective of this study was to investigate the adsorption mechanism through both experimental and theoretical analyses. A physical model was successfully applied to establish a strong correlation between the adsorption properties, the adsorbent characterization, and the MB adsorption behavior. These findings provide new insights into the separation mechanism and contribute to a better understanding of the methylene blue adsorption process. Experimental section Synthesis of activated carbon Activated carbon (AC) was prepared from olive waste following a modified procedure12. The raw olives were washed with demineralized water and dried in an oven at 100 °C for 24 h. The dried material was then ground to particles of 200–400 µm. The olive particles were impregnated with 85% phosphoric acid (H₃PO₄) at a 1:1 weight ratio for 24 h. The impregnated material was heated at 100 °C to remove excess moisture, then washed with deionized water and NaHCO₃ to neutralize residual acidity. Carbonization was performed at 600 °C for 4 h, and the resulting AC was washed thoroughly with distilled water and dried at 100 °C for subsequent use. Characterization of the adsorbent Various techniques were employed to characterize the prepared activated carbon. The crystallinity of the adsorbent was analyzed by X-ray diffraction (XRD) using a Philips MPD1880-PW1710 diffractometer. The functional groups were identified by Fourier transform infrared (FTIR) spectroscopy (Bruker Vertex 70-RAM II). The surface morphology of the activated carbon was examined using a scanning electron microscope (SEM, FEI Q250 Thermo Fisher). The textural properties were determined by nitrogen adsorption–desorption analysis using the Brunauer–Emmett–Teller (BET) method with a Micromeritics 3Flex analyzer. Study of adsorption Adsorption kinetics The adsorption experiments were conducted as follows: 50 mL of the model solution, containing 100 mg L⁻1 of methylene blue (MB), was placed in a glass vessel, and the pH was adjusted using dilute HNO₃. The pH values studied ranged from 2 to 10. A predetermined amount of adsorbent (0.01–0.9 g) was then added to the solution, followed by sonication at room temperature for 5 to 180 min. The absorbance of the solutions was measured using a UV spectrophotometer at λmax = 664 nm, corresponding to the maximum wavelength of MB. The equilibrium adsorption capacity is calculated using the following Eq. (1)12: where , , V and are the initial methylene blue concentration (mg L‐1), the final methylene blue concentration (mg L‐1), the solution volume (l) and the mass of AC (g), respectively. Kinetic models To examine the rate of the adsorption process, the pseudo-first order kinetic models and the pseudo-second order kinetic model are given by the following Eq. 4 and 5, respectively12: where (mg.g-1) was the adsorption capacity in equilibrium. (mg.g-1) are adsorption capacity in any time (t, min). (min-1) and (g mg‐1 min-1) was the equivalent adsorption velocity constants for pseudo‐first‐order and pseudo‐second‐order respectively. Isotherm modeling Classical models The classical isotherm model used to fit the adsorption isotherm was the Langmuir (Eq. 4 ) and Freundlich models (Eq. 4)12 : , and represent respecevely the concentration at equilibrium in (mg L-1), Langmuir and Freundlich constant. To further elucidate the mechanisms governing MB adsorption on Cs, advanced statistical physics models were employed. These models were used to complement and validate the results of classical adsorption models, providing a deeper understanding of the adsorbent-adsorbate interaction dynamics13. A multilayer physical model was employed to characterize the adsorption systems (Eq. 6). This model assumes that the adsorption of MB onto AC occurs as a multilayer process, involving the formation of a limited number of adsorbate layers. In characterizing the adsorption interactions, the model provides two distinct adsorption energies: one corresponding to dye–adsorbent surface interactions and another related to dye–dye interactions. The first adsorption energy is associated with the formation of the initial adsorbate layer, while the second arises from the formation of additional, yet limited, adsorbate layers. According to this model, the total number of dye molecule layers formed is expressed as 14. The expression of this model is defined as a function of the receptor site density (), the number of MB molecules attached per site (), and two half-saturation concentrations, and , which correspond to the formation of the first and second adsorbate layers, respectively. It is expressed by the following equation14: Both half-saturation concentrations are model parameters directly related to the adsorption energies. The corresponding expressions of the adsorption energies are given by14: where Cs (mg L-1) was the water solubility of MB dye. Results and discussion Characterization of the AC The FTIR spectra of the activated carbon are shown in Fig. 1. The band at 3420 cm⁻1 was attributed to –OH vibrations. The bands at 2924 cm⁻1 and 3000 cm⁻1 correspond to –CH₂ and aliphatic –CH groups, respectively. Additionally, the bands at 1600 cm⁻1 and 1500 cm⁻1 were assigned to C = C functional groups. The bands at 1140 cm⁻1 and 2325 cm⁻1 were attributed to C–O and C–C bonds, respectively. FTIR spectra of the AC5,26. The crystal structure of the activated carbon was analyzed by XRD (Fig. 2). The diffraction pattern shows two peaks at 2θ = 25° and 42°, corresponding to the (002) and (100) planes, indicative of disordered carbon5. The broadness of these peaks suggests that the material possesses an amorphous structure15. XRD of the AC5,26,28. The surface morphology was examined using SEM, as shown in Fig. 3. The images reveal a highly porous material with abundant surface pores. This porous structure enhances adsorption by providing sufficient accessible sites for the target adsorbate molecules. SEM of the AC5,26,27. The textural properties of the activated carbon were investigated using N₂ adsorption–desorption isotherms, and the results are summarized in Table 1. According to the IUPAC classification, the isotherm (Fig. 4) corresponds to a type I microporous isotherm5. Nitrogen adsorption occurs at low pressures due to the presence of empty sites, and the uptake gradually increases until reaching a plateau at higher pressures, reflecting the occupation of adsorption sites by nitrogen molecules. Table 1Textural parameters of activated carbon5,26.SBET (m2/g)1565Vmic(cm3/g)0.649Vmes(cm3/g)0.027Vtotal (cm3/g)0.676 Textural parameters of activated carbon5,26. N2 isotherm on the AC5,26,28. MB adsorption studies on the AC The pH of a solution critically influences phenol adsorption by affecting the surface charge and interaction between the adsorbent and adsorbate. Under acidic conditions, adsorption is enhanced due to strong electrostatic attraction, whereas at neutral pH, adsorption capacity decreases because of the dominance of positive surface charges12. Figure 5 presents the removal efficiency of MB on activated carbon at different pH values (2–10). The results indicate that the highest removal efficiency (95%) occurs at pH 2 and decreases significantly to 25% as the pH increases. pH of the MB. The effect of adsorbent mass on MB adsorption was investigated, and the results are shown in Fig. 6. The removal efficiency increased as the adsorbent mass was raised from 0.01 g to 0.1 g, which can be attributed to the greater specific surface area and availability of adsorption sites5. The maximum adsorption efficiency and equilibrium were achieved at an adsorbent mass of 0.2 g, which was therefore used as the optimal mass in subsequent experiments. adsorbent mass on the MB adsorption on the AC. The relationship between MB adsorption and contact time is illustrated in Fig. 7. The adsorption efficiency increased with contact time and reached equilibrium after 20 min. During the initial stage, adsorption occurs rapidly due to the abundance of available pores on the activated carbon surface, which facilitates faster mass transfer of MB from the solution to the adsorbent16. relationship between MB adsorption and the contact time. Adsorption kinetics studies The kinetic study of MB adsorption on activated carbon, along with the parameters obtained from the pseudo-first- and pseudo-second-order models based on Eqs. (2) and (3), is presented in Fig. 8 and Table 2. The pseudo-second-order model provides the best fit, with a correlation coefficient (R2) of 0.997. Representative plots of the pseudo-second-order model are shown in Fig. 9. These results indicate that the adsorption of MB on activated carbon is predominantly governed by pseudo-second-order kinetics, suggesting that chemisorption is the main mechanism. Adsorption kinetic of MB on the AC. Table 2Adsorption isotherms parameters.MBPseudo 1st orderqeexp23.21k1 (min-1)0.074qe (mg.g-1)0.03R20.432Pseudo 2nd orderk2 (g mg-1 min-1)0.091Qe (mg g-1)24.32R20.998h (mg g-1 min-1)57.32t1/2 (min)0.42 Adsorption isotherms parameters. Pseudo-second order plots for MB. Additionally, the half-adsorption time (t₁/₂) represents the time required to remove 50% of the target compound at equilibrium. A low half-adsorption time reflects a high affinity between the adsorbent and the dye, as evidenced by the rapid removal of most of the dye during the initial adsorption period. Adsorption isotherms The Freundlich and Langmuir isotherm models, based on Eqs. (4) and (5), were applied to analyze the equilibrium data for methylene blue (MB) adsorption (Fig. 10). The Langmuir model assumes monolayer adsorption on a homogeneous surface, while the Freundlich model describes multilayer adsorption on a heterogeneous surface12. The experimental data were evaluated using the R2 values obtained from the linearized plots of each isotherm model. As shown in Table 3, the Langmuir model provides the best fit, with R2 = 0.993, indicating that MB adsorption on the activated carbon occurs predominantly as monolayer coverage on a uniform surface. MB adsorption fitted with Langmuir and Freundlich models. Table 3Kinetics parameters for pseudo 1st order and pseudo2nd order.IsothermsParametersMBLangmuirqmax (mg g-1)34.3KL (L mg-1)1.01RL0.01R20.998FreundlichKF30.65n6.58R20.642 Kinetics parameters for pseudo 1st order and pseudo2nd order. Physical statistical interpretations The experimental data and the physical statistical prediction are shown in Fig. 11. The best-fitting advanced statistical physics model for MB adsorption on AC was found to be a multilayer model (Eq. 6). The parameters of this model, presented in Table 4, provide valuable insights into the adsorption mechanism of MB. Adsorption isotherms of MB on AC adsorbent. Table 4Adjustment parameter values corresponding to the fit model.Temperature (K)n(mg/g)(mg/g)(kJ/mol)(kJ/mol)2981.7856.32235.2118.9015.613031.5460.74209.6215.4111.443131.3269.17198.6211.8510.42 Adjustment parameter values corresponding to the fit model. n parameterThis parameter provides information on the orientation of MB molecules on the AC surface. According to the multilayer model17,18, three situations can occur depending on the value of : when , MB molecules interact with at least two adsorption sites, resulting in a parallel tilt of the molecules during adsorption; when , the molecules interact with a single adsorption site, indicating a non-parallel orientation; and when , both parallel and non-parallel orientations occur simultaneously in varying proportions.The calculated values for MB were greater than 1, indicating that MB molecules predominantly interact with single adsorption sites in a non-parallel orientation. Figure 12 shows the effect of temperature on ; overall, an increase in temperature reduces after a slight initial rise at lower temperatures. This decrease in suggests a shift in MB orientation toward a parallel or mixed inclination on the AC surface19.It was observed that the parameter had values of 1.78, 1.54, and 1.32 at 298, 303, and 313 K, respectively-all greater than unity. This indicates that a vertical molecular orientation and a multi-ionic adsorption mechanism were involved in the interactions between MB ions and the active sites of AC19. These results suggest that multiple MB ions interacted with a single active site on the adsorbent surface (i.e., a multi-interaction mechanism), leading to a predominantly vertical alignment of the adsorbed dye molecules. n parameter This parameter provides information on the orientation of MB molecules on the AC surface. According to the multilayer model17,18, three situations can occur depending on the value of : when , MB molecules interact with at least two adsorption sites, resulting in a parallel tilt of the molecules during adsorption; when , the molecules interact with a single adsorption site, indicating a non-parallel orientation; and when , both parallel and non-parallel orientations occur simultaneously in varying proportions. The calculated values for MB were greater than 1, indicating that MB molecules predominantly interact with single adsorption sites in a non-parallel orientation. Figure 12 shows the effect of temperature on ; overall, an increase in temperature reduces after a slight initial rise at lower temperatures. This decrease in suggests a shift in MB orientation toward a parallel or mixed inclination on the AC surface19. It was observed that the parameter had values of 1.78, 1.54, and 1.32 at 298, 303, and 313 K, respectively-all greater than unity. This indicates that a vertical molecular orientation and a multi-ionic adsorption mechanism were involved in the interactions between MB ions and the active sites of AC19. These results suggest that multiple MB ions interacted with a single active site on the adsorbent surface (i.e., a multi-interaction mechanism), leading to a predominantly vertical alignment of the adsorbed dye molecules. parameterThis parameter estimates the number of adsorption sites occupied at saturation. Figure 13 illustrates the temperature effect on Dₘ, which shows an inverse relation ship with . As decreases with increasing temperature, the adsorption density (Dₘ) rises, indicating that a lower corresponds to more occupied adsorption sites19. parameter This parameter estimates the number of adsorption sites occupied at saturation. Figure 13 illustrates the temperature effect on Dₘ, which shows an inverse relation ship with . As decreases with increasing temperature, the adsorption density (Dₘ) rises, indicating that a lower corresponds to more occupied adsorption sites19. parameterThe maximum adsorption capacity depends on the values of and Dₘ. Figure 14 shows the temperature effect on . The decrease of the Qsat values with temperature confirmed the exothermic interaction between MB and AC19. The Qₛₐₜ values followed the same trend observed for the parameter n, indicating that the adsorption mechanism of this dye is primarily controlled by n parameter. parameter The maximum adsorption capacity depends on the values of and Dₘ. Figure 14 shows the temperature effect on . The decrease of the Qsat values with temperature confirmed the exothermic interaction between MB and AC19. The Qₛₐₜ values followed the same trend observed for the parameter n, indicating that the adsorption mechanism of this dye is primarily controlled by n parameter. Energetic aspectThe calculation of adsorption energies provides valuable insight into the adsorption mechanisms of MB on AC. Using the half-saturation concentrations and the expressions in Eqs. (7) and (8), the adsorption energies of MB were calculated at different temperatures. The results, summarized in Table 4, show that the negative values of ΔE confirm the exothermic nature of MB adsorption on AC. Moreover, the ΔE values for MB were less than 40 kJ·mol⁻1, suggesting a physical adsorption process. As expected, the ΔE₁ values were higher than ΔE₂ because ΔE₁ corresponds to interactions between MB and the AC active sites, whereas ΔE₂ reflects MB–MB interactions18,19 (Table 5). Energetic aspect The calculation of adsorption energies provides valuable insight into the adsorption mechanisms of MB on AC. Using the half-saturation concentrations and the expressions in Eqs. (7) and (8), the adsorption energies of MB were calculated at different temperatures. The results, summarized in Table 4, show that the negative values of ΔE confirm the exothermic nature of MB adsorption on AC. Moreover, the ΔE values for MB were less than 40 kJ·mol⁻1, suggesting a physical adsorption process. As expected, the ΔE₁ values were higher than ΔE₂ because ΔE₁ corresponds to interactions between MB and the AC active sites, whereas ΔE₂ reflects MB–MB interactions18,19 (Table 5). Effect of temperature on the n parameter for the MB. Effect of temperature on the Dm parameter for the MB. Effect of temperature on the maximum adsorption capacity. Table 5Adsorption of various dyes by AC ad sorbents.AdsorbentsAdsorption capacity (mg. g-1)ReferencesAC from rice husk waste27.8 20 AC from black cumin seeds16.8 21 AC from peanut shell wastes15.4 22 AC from Parthenium hysterophorus11.3 23 AC from grape wood4.8 24 AC from Coriandrum sativum94.9 7 AC from Calicotome villosa wood169.8 25 This Work34.3 Adsorption of various dyes by AC ad sorbents. Comparison with results reported in the literature Table 4 presents a comparison between the maximum adsorption capacity (qm = 34.4 mg g⁻1) of AC prepared from olive waste and those of other adsorbents reported in the literature. The MB adsorption capacity of AC is higher/lower than that reported for activated carbons prepared from various raw materials. For instance, the highest adsorption capacity reported in the literature was 169.8 mg g−1 for activated carbon derived from Calicotome villosa wood25, whereas the lowest value, 4.8 mg g−1, was obtained for activated carbon produced from grape wood24. This wide variation can be attributed primarily to differences in the raw materials used, as well as to variations in pyrolysis conditions and activation methods. Therefore, the adsorption capacity obtained from activated carbon produced using olive waste appears promising, suggesting the need for further studies to optimize its production conditions. Conclusion The performance of the activated carbon (AC) adsorbent for MB dye removal was systematically evaluated. The AC was characterized using FTIR, SEM, XRD, and BET techniques. Key factors affecting MB adsorption included pH, adsorbent mass, and contact time. Kinetic studies and adsorption isotherms were analyzed using the pseudo-second-order model and the Langmuir isotherm, respectively. The adsorption mechanism was further investigated using a physical multilayer model, with steric parameters , Dₘ, and Qₘ evaluated and discussed. Differences in adsorption capacity were found to be primarily influenced by variations in the parameter. Adsorption energy analysis revealed that MB adsorption was exothermic and occurred via a physisorption process. Acknowledgements The authors gratefully acknowledge the funding of the Deanship of Graduate Studies and Scientific Research, Jazan University, Saudi Arabia, through project number: (JU-202502103-DGSSR- ORA-2025). Author contributions Souhail Mohammed bouzgarrou: Conceptualization, data curation, investigation Jedli Hedi, Rym methodology :Validation, visualization. Ehab Sabi: Acquisition Khalifa Slimi: Writing–review & editing. Data availability The datasets used and/or analysed during the current study available from the corresponding author on reasonable request. Competing interests The authors declare no competing interests. Footnotes Publisher’s note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations. Contributor Information Souhail Mohammed Bouzgarrou, Email: sbouzgarrou@jazanu.edu.sa, Email: s_bouzgarrou2002@yahoo.fr. Hedi Jedli, Email: jedli.hedi@gmail.com. References Associated Data Data Availability Statement The datasets used and/or analysed during the current study available from the corresponding author on reasonable request.