Research on the possibility of using olive pit biomass in recycling metals from slag Authors: Albert Smalcerz, Jerzy Łabaj, Szymon Ptak, Robert Findorak, Tomasz Matuła, Marzena Półka, Tomasz Wojtal, Leszek Blacha Published: 2025 ABSTRACT AbstractAccording to the EU Sustainable Development Goals, it is necessary to search for new technologies that promote sustainable development and optimize the use of resources, raw materials and energy. This article presents the results of research on the use of biomass in metal recycling processes. Unlike fossil fuels, including the coke used in metallurgy, biomass is characterized by a closed carbon cycle. The research results prove that the use of biomass (e.g., olive pits) agents as reductants in the pyrometallurgical process of copper and lead recovery is effective and can be implemented in industrial practice. The significant reduction in copper content in waste slag allows this material to be classified as safe industrial waste, in accordance with standard legal requirements for waste management. This also has an impact on the carbon footprint of the pyrometallurgical process for processing secondary metal-bearing raw materials. As the research results show, the use of biomass led to a 98% reduction in copper and over 60% reduction in lead from the tested slag.Keywords: Biomass, Pyrometallurgy, Slag reduction, ThermogravimetrySubject terms: Bioenergy; Process chemistry; Reactive precursors; Design, synthesis and processing Introduction The circular economy model introduced in recent years, which aims to minimize the use of fossil raw materials and the amount of waste produced while limiting pollutant emissions, is based on the creation of technological systems in which waste from some processes is used as raw material in other processes. This alternative to the linear economy has a negative impact on the environment and is based on increasing the processing of natural resources and thus increasing the amount of waste produced in production1,2. The circular economy has forced broad actions aimed at improving the efficiency of the use of energy resources and the industrial use of renewable raw materials, including various types of biomass from agrofood production. This group of waste includes, among others, olive pit biomass. Annually, more than 3 million tons of olives are harvested worldwide, and their main producers include Spain, Italy, Greece and Turkey. Thus, more than 300 thousand tons of olive pits are produced3. According to the literature, processing one ton of olives yields 27% oil and 73% pomace. Pomace contains 60% water and over 11% pits. Some pomace is involved in the secondary oil recovery process, whereas pits and extracted pomace are used in various technological processes3,4. Figure 1 presents a schematic of the mass balance of the olive oil production process3. Mass balance of the olive oil production process (reproduced on the basis of3). The olive fruit can be divided into three parts in terms of structure (Fig. 2). The outer part, which is the skin of the fruit (epicarp), constitutes up to 3% of the fruit mass. The main part of the fruit is the pulp (mesocarp), which constitutes 70 to 80% of the fruit mass. The third part is the fruit pit (endocarp), which accounts for up to 20% of the total fruit mass5. Cross-section of an olive fruit: 1–endocarp (pit/stone); 2–epicarp (skin); 3–mesocarp (pulp, flesh); 4–kernel/seed. Olive pits consist mainly of hemicellulose (26.0 wt%), cellulose (20.9 wt%) and lignin (35.6 wt%). They are characterized by a relatively high heating value (heat of combustion), which makes them a valuable component of solid biofuels. The low ash content also significantly expands the possibilities for their use as fuel6. Currently, a technology that allows the use of olive pits for the production of bioethanol has also been developed7–9. When the possibility of using olive pits as solid fuel is analyzed, it should be emphasized that this waste unfortunately contains certain amounts of oil substances, which negatively affect their combustion as biofuel. This mainly concerns pits extracted in the oil production process. The content of oil substances causes, among other factors, increased emissions of carbon dioxide and nitrogen oxides compared with those of other solid biofuels10. An important direction for the use of olive pits is the production of activated carbon. It is mainly used to remove dyes, odors or various types of impurities from aqueous solutions11–18. The presented characteristics of olive pits, considering their basic physicochemical properties, indicate the possibility of their use for the production of solid fuel or as a component for the production of biofuels. Thus, this type of biomass can be an alternative raw material to the solid carbon fuels used in many industries. This work presents and discusses the possibility of using olive pits in the metallurgical industry as alternative reducing agents in the pyrometallurgical processing of metal recovered from metallurgical slag. Currently, this type of process uses mainly solid carbon materials, i.e., coke and coke breeze19. The solution proposed by the authors makes it possible to reduce the carbon footprint by using biomass and thus creates economically advantageous conditions for processing and limiting the deposition of environmentally harmful postindustrial solid waste. Notably, there are studies in the literature that present the research results on the use of other types of agrofood biomass in high-temperature metallurgical processes. This includes waste cooking oil, nut shells, and sunflower husks20–30. In the article, the authors proposed a number of basic research (discussed in more detail in section “Research plan” Research plan) aimed at characterizing olive pit biomass for use as a reducing agent in the pyrometallurgical process. The literature contains a number of data on the use of various types of biomass in metallurgical processes, but there are no research results on olive pits. Therefore, the research discussed in the article for energy materials, determining the behavior of biomass at high temperatures by conducting thermogravimetric tests and conducting basic tests of reductive slag melting are aimed at determining the degree of removal of metals i.e., Cu and Pb, and will demonstrate their usefulness. Materials In studies of metallurgical slag reduction, biomass in the form of olive pits was used. The results of the ultimate analysis of the biomass used are presented in Table 1. The contents of basic components were determined using an ELTRA CHS HELIOS analyzer. The sample combustion temperature was 1400 °C. The results presented in Table 1 represent the average value of five measurements of the tested material. The contents of carbon, nitrogen, sulfur, and oxygen in cherry pits were analyzed using energy-dispersive X-ray spectrometry (EDS). For this purpose, the pits were ground, seasoned in an open container, and pressed into a pellet. The analysis was performed using a Thermo Noran EDS spectrometer (System Seven) using a primary electron beam with an energy of 15 keV and an intensity of 1.16 nA. The analysis was performed using an Astimex Standards Ltd. MINM25-53 + FC system, and the quantitative analysis results were corrected using the PROZA method (which involves fitting exponential curves describing the ionization distribution as a function of distance from the material surface to the experimental results; this method yields much better results in the case of light elements and in the case of materials containing elements with large differences in atomic numbers). The hydrogen concentration value was taken from the literature31. The results of the chemical composition of the slag are presented in Table 2. Table 1Results of the ultimate analysis of olive pit biomass.SampleUltimate analysis, wt%CSNHO2Olive pits biomass44.820.010.456.8947.10 Results of the ultimate analysis of olive pit biomass. Table 2Chemical composition of the slag used in the reduction process.ComponentCuPbFeSiO2CaOContent, wt%10.302.2511.1134.5014.12 Chemical composition of the slag used in the reduction process. The measurement uncertainty associated with the EDS method is primarily related to particle size. In fine-grained materials, the method error increases exponentially with decreasing grain size. In this case, the error was estimated as follows: Pb ± 2%; Cu ± 2%; Fe ± 2%; O ± 5%. Given the differences in the chemical affinity of copper/lead for oxygen and iron for oxygen, the present research focused on the first two elements. Before the reduction tests, the slag was subjected to phase analysis, which was carried out using a Philips X-ray diffractometer X’Pert powder 3 system. The analysis was aimed at identifying the phases containing metal components, i.e., copper, lead and iron. A tube with a copper anode (λCuKα = 1.54178 Å) supplied with a current of 30 mA at a voltage of 40 kV and a graphite monochromator was used. recording-ray diffraction patterns were obtained with a step size of 0.026° and a 2θ value ranging from 10 to 90°. The tests were carried out on powder samples. The phase composition was identified using the ICDD PDF-2 and COD databases. The strongest diffraction reflections coincided with each other, while differences in the occurrence of some low-intensity reflections were observed. This difference translated into differences in the phase composition of the tested samples. In the tested sample, the oxide phases containing Cu, Pb and Fe were identified as follows30: Fe1.966O2.963–tetragonal maghemite, Fe1.966O2.963–tetragonal maghemite, Cu2O–cuprite with a regular crystal structure, Cu2O–cuprite with a regular crystal structure, Al2PbSi2O8 with a monoclinic structure, Al2PbSi2O8 with a monoclinic structure, PbO–lead(II) oxide with an orthorhombic structure (massicot). PbO–lead(II) oxide with an orthorhombic structure (massicot). The biomass sample was dried at a negative pressure of approx. 50 Pa and a temperature of 105 °C. Methods Research plan The pyrometallurgical process is complex, and many factors affect its efficiency. Here, attention should be given to the proper method of determining the stability of the substrates used, including mass loss, the amount of volatile components and their nature. High-temperature tests at temperatures significantly exceeding 1000 °C require, on the basis of similarity with the processes carried out in practice, the development of a test procedure followed by data acquisition. To determine the possibility of using olive pits as reducing agents in the process of recovering metal from slag, the following test program was adopted: Synthetic slag with a composition similar to that of the material derived from the copper production process in a flash furnace was prepared. Synthetic slag with a composition similar to that of the material derived from the copper production process in a flash furnace was prepared. The heat of combustion of the olive pits was determined. The heat of combustion of the olive pits was determined. The reactivity index was estimated. The reactivity index was estimated. Thermogravimetric analysis was performed on a sample of olive pits in an inert and oxidizing atmosphere. Thermogravimetric analysis was performed on a sample of olive pits in an inert and oxidizing atmosphere. The reduction process in slag melting with the addition of a reducing agent in the form of olive pit biomass was studied. The reduction process in slag melting with the addition of a reducing agent in the form of olive pit biomass was studied. Determination of the heat of combustion The heat of combustion of the olive pits was determined in accordance with the EN ISO 1716 standard. The test consisted of complete combustion of the test sample in a calorimetric bomb under an oxygen atmosphere immersed in water. The temperature of the water jacket was recorded. After the biomass sample (m = 1 ± 0.0005 g) was placed in the calorimetric bomb, oxygen was injected into the container to create an atmosphere enabling complete combustion of the sample. Since the container was placed in a double water jacket, it was possible to accurately determine the heat of combustion, considering the heat from the condensation of water vapor generated during the combustion process. The sample was ignited by a suitable electrical system enabling the flow of electric current through the ignition wire. All the data were recorded by a computerized measurement system. The heat of combustion of the material was calculated after corrections for additional thermal effects were determined. Three consecutive tests were performed, and the results were averaged. A diagram of the bomb calorimeter is shown in Fig. 3. Caloric bomb for heat of combustion measurements according to EN ISO 1716. 1–ignition leads; 2–oxygen inlet; 3–temperature sensor; 4–stirrer; 5–calorimetric bomb; 6–outer (thermally insulated) water jacket; 7–crucible with the test specimen. Exact differential method was used to estimate measurement uncertainty. For single measurement, uncertainty was estimated to be 1.5%, propagating to for average value. Determination of the reactivity of the tested biomass Fuel reactivity is the ability of a material to react with a selected oxidizing agent under precisely defined conditions. In practice, the reactivity of solid fuels is most often assessed in terms of carbon dioxide (carboxyreactivity), oxygen (oxyreactivity) and water vapor (hydroxyreactivity). The choice of the oxidizing agent depends primarily on the direction of fuel consumption. When a reducing agent is used to reduce metal oxide compounds, its carboxyreactivity must be determined. The degree of sample conversion () is calculated on the basis of the weight loss curve from the moment of interaction with . In this case, the reactivity is determined by the maximum rate () of mass loss in the monitored interval. The evaluation factor is also the time it takes to reach this maximum speed as well as the time it takes to reach 50% conversion () during the reaction with . The relevant dependencies (1) and (2) are presented below. where is the fixed weight of biomass loss and is the initial biomass weight, mg; is the maximum rate of fixed biomass loss, mg/min. The transition rate of copper was estimated from the Eq. (3)30: where and are initial and final mass (Table 6) of the slag, respectively, g; and – are initial (Table 2) and final (Table 6) metal content, wt%. Table 6Results of reductive slag melting using olive pit biomass as a reducer.NoInitial slag mass, gReducer typeReducer mass, gTime, hMetal mass, gCalculated slag mass, gMetal content in slag, % wtSCu, %CuPbFe180.00 ± 0.02Olives pits18.28 ± 0.02110.59 ± 0.0263.45 ± 0.070.84 ± 0.011.07 ± 0.0113.5 ± 0.0793.532210.84 ± 0.0262.88 ± 0.070.76 ± 0.010.98 ± 0.0113.2 ± 0.0794.203310.54 ± 0.0261.91 ± 0.070.60 ± 0.010.95 ± 0.0113.4 ± 0.0795.494413.09 ± 0.0261.15 ± 0.070.43 ± 0.010.90 ± 0.0112.9 ± 0.0796.815513.78 ± 0.0262.30 ± 0.070.21 ± 0.010.89 ± 0.0112.8 ± 0.0798.41 Results of reductive slag melting using olive pit biomass as a reducer. 80.00 ± 0.02 18.28 ± 0.02 10.59 ± 0.02 63.45 ± 0.07 0.84 ± 0.01 1.07 ± 0.01 13.5 ± 0.07 10.84 ± 0.02 62.88 ± 0.07 0.76 ± 0.01 0.98 ± 0.01 13.2 ± 0.07 10.54 ± 0.02 61.91 ± 0.07 0.60 ± 0.01 0.95 ± 0.01 13.4 ± 0.07 13.09 ± 0.02 61.15 ± 0.07 0.43 ± 0.01 0.90 ± 0.01 12.9 ± 0.07 13.78 ± 0.02 62.30 ± 0.07 0.21 ± 0.01 0.89 ± 0.01 12.8 ± 0.07 Thermogravimetric analysis (TGA) of the samples was performed with a thermal analyzer (Derivatograph-C, MOM Budapest) to study their thermal stability and reactivity with CO2. The sample was placed in an Al2O3 crucible, and in the first step, the heating mode was linear, with the sample being heated to 1160 °C at a heating rate of 15 K/min and subsequently heated to 1200 °C at a reduced heating rate of 0.5 K/min. The linear heating in the first step (pyrolysis) was performed in a N2 atmosphere, and the quasi-isothermal second step (for reactivity) was performed under CO2 conditions. The flow rates of the injected gases were held constant at 0.05 L/min. Thermogravimetric analysis During the TGA of the biomass, a TGA Q500 device manufactured by TA Instruments was used. This method allows studies to be conducted in both an oxidizing atmosphere and an inert atmosphere. In these studies, high-purity nitrogen was used as the inert atmosphere. The device allowed for studies with different sample heating rates from 0.01 to 100 K/min, with an estimated temperature measurement uncertainty of 1 K and a measurement resolution of 0.1 K. The sample mass was measured with a resolution of 0.1 µg and a measurement inaccuracy of 0.01% plus baseline drift not greater than 50 µg (for initial sample mass measurement). Calculated maximum weight uncertainty was equal to 3%. The sample mass ranged from 20 to 22 mg, and the sample heating rate was 100 K/min. Slag reduction studies To conduct this research under conditions similar to those used in industrial practice, reductive slag melting was carried out in a Czylok resistance pit furnace, model PT 40/1300. The process was carried out at 1300 °C in alundum crucibles, the biomass sample was introduced into the furnace at ambient temperature. Heating rate was equal to 10 K/min. The variable parameter in the research was time, which ranged from 1 to 5 h. The maximum duration of the test was close to the actual time of the operations conducted under industrial conditions. The estimated mass of elemental carbon, on the basis of stoichiometric calculations, necessary to ensure the complete reduction of the metal oxides in the slag sample, i.e., copper and lead, was equal to 2.949 g. Examples of reactions (4, 5, 6, 7) are shown below. The slag mass was 80 g, which was determined by the dimensions of the crucible used. The mass of the carbon demand was calculated based on Table 2. It is possible to determine the mass of main components (8): As the molar mass of , , , is equal to 79.55 g/mol, 63.55 g/mol, 16 g/mol, 12 g/mol accordingly, mass of might be calculated (8–10). 63.55 g/mol of and 16 g/mol of will produce 79.55 of . So 8.24 g of will result in 10.31 g of . Based on reaction (6), 79.55 g/mol of result in 28 g/mol of . As a result, 10.31 g of will react with 3.63 g of , and finally 1.56 g of is needed. By analogy, calculations for lead were conducted. Mass of in sample was equal to (9): (9) It is expected, that 207.2 g of and 16 g of results in 223.2 g of . Therefore, 1.8 g of will result in 1.94 g of . Molar mass of is equal to 207.2 g/mol, so finally, based on reaction (7), 223.2 g/mol of and 28 g/mol of is needed. For 1.94 g of , 0.243 g of will require 0.104 g of C. So in summary, for reaction (6), calculated mass of carbon was equal to 1.56 g. For reaction (7), calculated carbon demand was equal to 0.104 g. Therefore, total demand for carbon . Additionally, in the tested process, a biomass weight of 18 g was included, which was necessary for the Boudouard reaction to generate a reduction atmosphere in the working chamber of the device. It should be emphasized that this article does not analyze the process of iron reduction to the metallic phase, which, according to the data presented, took place. After the experiment was completed, the mass of the melted metal and the mass of the secondary slag were determined for each sample. After being cooled in the furnace, both the metal and the slag were subjected to chemical analysis to determine the contents of the main metallic components, i.e., copper, lead and iron. The chemical composition of the slag was analyzed using a Rigaku Primus II X-ray fluorescence spectrometer. The measurement procedure was based on the EN 15,309:2007 standard. The metal alloy was analyzed using the WDXRF technique. The elemental composition was analyzed using the SQX standard-free analysis program. The obtained results allowed for the efficiency of the tested reduction process to be determined. A diagram of the station with the PT-40/1300 furnace used in the tests is shown in Fig. 4. PT-40/1300 furnace: 1–controller; 2–ceramic covers; 3–thermocouple; 4–heating elements; 5–ceramic crucible. Slag mass after the process (Table 6) was calculated with the formula (10): where is the mass of the crucible with the charge (after the process), kg; is the mass of the empty crucible, kg; is the metal mass, kg. Results Heat of combustion Table 3 presents the determined values of the heat of combustion of the olive pits and other selected types of biomass (for comparison). The standard deviation values for a particular test series were also given. All biomasses were tested using the same methodology and the same device used in the case of the olive pits. Table 3Results of the heat of combustion values for the selected types of biomass.Biomass typeNotesWalnut shell18,040 ± 27018,130 ± 1901163218,260 ± 27018,100 ± 270Peanut shell18,270 ± 27018,010 ± 1905593017,360 ± 26018,390 ± 280Olive pits16,860 ± 25016,780 ± 180202Own elaboration16,930 ± 25016,550 ± 250Cherry pits19,540 ± 29020,000 ± 210398Own elaboration20,210 ± 30020,240 ± 300Pinus sylvestris cones18,360 ± 28018,010 ± 190318Own elaboration17,930 ± 27017,730 ± 270 Results of the heat of combustion values for the selected types of biomass. The results for olive pits meet the acceptance criteria described in ISO 1716:2018, as all obtained results are within 5% of the average value. The analysis of the data presented in Table 3 reveals that the heat of combustion of olive pits is approximately 16,800 kJ/kg and is lower than the heat of combustion of other listed types of biomass. If olive pits were used in metallurgical technologies as fuel, then the production of the same amount of energy would require a larger mass supply than would other types of biomass. On the other hand, this parameter is even less favorable than that of metallurgical coke, which is the basic fuel used in pyrometallurgical processes. According to our study, the average heat of combustion of coke is 27 MJ/kg; thus, to produce a comparable amount of energy, more than 60% more olive pits than coke would be needed. Olive pit biomass reactivity From the perspective of the use of olive pits as a reducing agent in pyrometallurgy carried out in electric furnaces, from a technological point of view, its reactivity should be considered at least as important a parameter as is the heat of combustion. A summary of the results of the reactivity measured for olive pit biomass is presented in Table 4. For comparison, the table also includes data concerning the reactivity measured for typical carbon-bearing materials used in pyrometallurgical metal production processes, i.e., coke (C), flotation concentrate (FC) and brown coal (BC). Table 4Results of the reactivity of olive pit biomass and the chosen carbon-bearing materials.IDSample nameOPBOlive pits0.243992.50 ± 0.023.62 ± 0.0271.487.70CCoke0.015607.50 ± 0.0268.02 ± 0.021.1349.11FCFlotation concentrate0.058778.50 ± 0.0214.92 ± 0.0231.6016.25BCBrown coal0.1123111.00 ± 0.0212.97 ± 0.0251.1510.40–maximum rate of reactivity; –reaction time; –time to reach 50% conversion in a atmosphere; –mass loss during the linear heating phase; –mass loss during quasi-isothermal heating Results of the reactivity of olive pit biomass and the chosen carbon-bearing materials. –maximum rate of reactivity; –reaction time; –time to reach 50% conversion in a atmosphere; –mass loss during the linear heating phase; –mass loss during quasi-isothermal heating Figure 5 shows the DTA curve obtained during the heating a sample of olive pit biomass (OPB) in an atmosphere of inert gas and , and Fig. 6 shows the observed change in the conversion coefficient. TGA of olive pits in a combined atmosphere (N2 used for linear heating at a rate of 20 °C/min and CO2 used for quasi-isothermal heating). Conversion of OPB to other carbon materials (BC–brown coal; FC–flotation concentrate; C–coke). An analysis of the obtained results (Table 4) revealed that olive pit biomass is characterized by relatively high reactivity. The conversion coefficient in this case was 71%. The time to reach the maximum reactivity for the olive pits was 2.5 min, whereas the time to reach 50% conversion in the atmosphere was 3.62 min. In comparison, the values of these indicators for the selected carbonaceous materials ranged from 7.5 to 11 min, and the tx50 values ranged from 13 to 68 min. Thermogravimetric analysis The results of the thermogravimetric analysis are presented in Figs. 7 and 8 in the form of a TGA curve. The test results indicate that the analyzed biomass samples were characterized by a transient moisture content of approximately 13–15% by mass. This is visible in the graphs presenting the test results in both the inert atmosphere (Fig. 7) and the oxidizing atmosphere (Fig. 8). The evaporation of transient moisture in the temperature range up to approximately 140 °C corresponds to the first peak of the DTG curve, i.e., the derivative of the sample mass changes over time. In both cases, the temperature of approximately 250 °C was determined to mark the beginning of thermal decomposition (pyrolysis), which corresponds to the point where the tangents to the TG curve intersect: 1) the tangent to the plateau after evaporation of transient moisture and 2) the section of the curve after the inflection point, resulting from the first phase of thermal decomposition (pyrolysis). In an inert atmosphere, two stages of pyrolysis are visible at temperatures of 260 °C and 350 °C. This is manifested by peaks of the DTG curve with values of 4.8–6%/min and most likely results from the thermal decomposition (pyrolysis) of hemicellulose and cellulose and, in the case of temperatures of approx. 350 °C, from the degradation of lignin33. The mass loss is similar in both cases, which is also evidenced by the temperature at which 50% mass is lost, i.e., 340–350 °C. In the case of testing in an inert atmosphere above approximately 400 °C, the phase of slow mass loss of the sample begins, which probably results from the process of sample coking. Moreover, the DTG curve obtained in an oxidizing atmosphere reveals an additional peak with a value of approximately 19.5%/min. This occurs at a temperature of approximately 460 °C, which corresponds to the self-ignition temperature of olive pit dust and may indicate the moment that flame combustion occurs in the sample. Results of TGA of OPB samples in an inert atmosphere. Results of TGA of OPB samples in an oxidizing atmosphere. A summary of the TGA results is presented in Table 5. Table 5TGA results of olive pit biomass samples in an inert and oxidizing atmosphere.ParameterInert atmosphereOxidizing atmosphereBeginning of thermal decomposition/ pyrolysis, °C253 ± 1254 ± 150% mass loss temperature, °C347 ± 1324 ± 11st phase of thermal decomposition/pyrolysis, °C265 ± 1271 ± 12nd phase of thermal decomposition/pyrolysis, °C348 ± 1342 ± 13rd phase of thermal decomposition/pyrolysis, °C–458 ± 1Residue, wt%10.33 ± 0.010.49 ± 0.01 TGA results of olive pit biomass samples in an inert and oxidizing atmosphere. Slag reduction The copper slag reduction results obtained with olive pit biomass as a reducing agent (Table 6) and their graphical interpretation (Fig. 9) demonstrate the possibility of using the tested biomass as a potential reducing agent to recover copper (as well as other metals) in the slag decopperization process. With increasing processing time (from 1 to 5 h), the copper mass content in the waste slag decreased from 0.84% Cu to 0.21% Cu. This increase was accompanied by an increase in the degree of slag decopperization in the range from 92 to 98% (Fig. 10). Moreover, this phenomenon was accompanied by a decrease in the content of copper in the obtained alloy. This effect was related to an increase in the extent of the reduction of the iron contained in the slag. The iron content in the metallic phase increased from 15.5% to almost 24% with increasing test duration. However, there was no significant effect of processing time on the lead content in waste slag, and its concentration ranged from approximately 0.9 to 1.1% Pb by weight. Changes in the copper and lead contents in postprocess (secondary) slag as a function of time. Change in the postprocess (secondary) slag decopperization coefficient with time. The analysis of the research results revealed that the use of olive pit biomass in the slag reduction process resulted in a copper content ≤ 0.5 wt% (in the secondary slag) after four hours of processing. In accordance with the applicable law, this slag can be considered safe for landfills or other purposes (e.g., construction)34. The obtained results indicate that the products and substrates do not fully balance, as the oxygen is released during the reduction process. The second possible cause is the evaporation of some components contained in the initial slag sample. Summary When analyzing the feasibility of using olive pits in metallurgical processes as an alternative reducing agent to the carbon-bearing materials commonly used in this process, a certain limitation of this process must be noted. This concerns the variable supply of this type of biomass on the market throughout the year, i.e., the so-called seasonal availability. The seasonal availability of certain types of biomass, including olive pits, is an important aspect that should be considered when designing technologies that enable their use. The accumulation of such biomass outside the period of its vegetation and harvest is difficult in this case, which can clearly create problems in the raw material supply chain. This research, which aimed to determine the possibility of using olive pits as an alternative reducing agent in the process of metal recovery from oxide slags, led to the following conclusions: Olive pits are a material characterized by high carboxyreactivity, which confirms the purpose of using them as reducing agents in the discussed technological process. Nevertheless, the application of this technology on an industrial scale requires prior large-scale research. Olive pits are a material characterized by high carboxyreactivity, which confirms the purpose of using them as reducing agents in the discussed technological process. Nevertheless, the application of this technology on an industrial scale requires prior large-scale research. The thermal decomposition and pyrolysis of olive pit biomass is typical for biomaterials consisting of lignin, cellulose and hemicellulose. The thermal decomposition and pyrolysis of olive pit biomass is typical for biomaterials consisting of lignin, cellulose and hemicellulose. During the experiments conducted, the efficiency of copper removal from the tested slag reached 98%, and the contents of copper and lead in the secondary slag after the reduction process decreased from 10.3 wt% Cu to 0.21 wt% Cu and from 2.25 wt% Pb to 0.89 wt% Pb, respectively. During the experiments conducted, the efficiency of copper removal from the tested slag reached 98%, and the contents of copper and lead in the secondary slag after the reduction process decreased from 10.3 wt% Cu to 0.21 wt% Cu and from 2.25 wt% Pb to 0.89 wt% Pb, respectively. The industrial use of olive pits in the proposed technology requires verification on a semitechnical scale to determine, among other things, the size and type of the generated process gases and their impact on the working elements of the device system. The industrial use of olive pits in the proposed technology requires verification on a semitechnical scale to determine, among other things, the size and type of the generated process gases and their impact on the working elements of the device system. The seasonal availability of biomass in the form of olive pits indicates the need to consider this factor when designing technologies that minimize or eliminate problems in the supply chain of this input material. The seasonal availability of biomass in the form of olive pits indicates the need to consider this factor when designing technologies that minimize or eliminate problems in the supply chain of this input material. The use of olive pits for the reduction of metallurgical slag, unlike conventional fossil fuels, has a measurable impact on achieving sustainable development goals. This applies to situations in which the biomass used ensures a closed cycle of carbon dioxide in the atmosphere. The use of olive pits for the reduction of metallurgical slag, unlike conventional fossil fuels, has a measurable impact on achieving sustainable development goals. This applies to situations in which the biomass used ensures a closed cycle of carbon dioxide in the atmosphere. Author contributions AS, SP and LB designed the experiments. JŁ, SP, RF and TM described the methods. JŁ, RF, MP, TW performed the experiments. JŁ, SP, AS and LB contributed to the interpretation of the results. LB, JŁ, SP and AS wrote the first manuscript. All authors reviewed the manuscript and significantly contributed to improve the manuscript. Funding This work was supported by the Silesian University of Technology research fund (grant numbers: 11/040/BK_25/0040 and 11/010/BK_25/0057) and by the Research Fund of Fire University. Data availability The datasets generated during and/or analyzed during the current study are available from the corresponding author upon reasonable request. Declarations Competing interests The authors declare no competing interests. Footnotes Publisher’s note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations. References Associated Data Data Availability Statement The datasets generated during and/or analyzed during the current study are available from the corresponding author upon reasonable request.