Advanced prediction of combustion phasing in methane homogeneous engines via in-cylinder ion current profiling and a novel ionic kinetics framework Authors: Elaheh Neshat, Amin Motevali Imami, Damon Honnery Published: 2025 ABSTRACT AbstractThis study presents a reduced ionic chemical kinetics mechanism for predicting combustion phasing in methane-fueled homogeneous charge compression ignition (HCCI) engines. Starting from the detailed GRI-Mech 3.0 mechanism, a reduced scheme with 22 species and 48 reactions was developed. Ionic reactions were then added, forming a comprehensive mechanism with 27 species and 54 reactions. The mechanism was integrated into a multi-zone combustion model and validated against experimental data from a CFR engine under four operating conditions. Results show that the mechanism accurately predicts the start of combustion (SOC), with a maximum error below 0.09%. In-cylinder pressure and temperature profiles closely match experimental data. The model also captures the behavior of key radicals and ions, including H₃O⁺, OH⁻, and O₂⁻. Exhaust emissions such as CO and CO₂ are predicted with relative errors under 12%, while UHC predictions show moderate discrepancies. Notably, electrons are fully consumed during combustion, while some ions remain in the exhaust. The proposed mechanism offers a reliable and computationally efficient tool for combustion diagnostics and control, with potential applications in low-temperature and fuel-flexible engine technologies.Keywords: Ion current, Chemical kinetics mechanism, HCCI combustion, MethaneSubject terms: Engineering, Chemical engineering Introduction Natural gas is one of the most important types of fossil energy source is widely used as fuel in combustion and reforming processes1,2. The most important component of natural gas is methane, due to having only one carbon in its chemical structure, it leads to the production of less carbon pollutant during combustion processes3,4. Due to its high calorific value, easy transportability, and numerous available sources, today this fuel is used as the main fuel in many combustion processes5,6. Combustion is a chemical process based on various reactions. During these reactions, many different species are produced and significant energy is released. For combustion modeling, existing reactions and species involved in them should be identified and accurate chemical kinetic mechanisms should be developed7,8. Several chemical kinetic mechanisms have been developed to model the methane combustion process9. GRI mechanism is the most important chemical kinetic mechanism developed for the simulation of methane and natural gas combustion10. In many studies, this mechanism has been used as the main mechanism, and its accuracy in predicting numerous combustion phenomena has been proven11–13. The latest version of this mechanism, GRI Mech.3, contains 53 species and 325 reactions. In this mechanism, NOx related reactions are also considered. Hughes et al. proposed a chemical kinetic mechanism consisting of 351 reactions and 37 species. The mechanism was named as Leeds mechanism and experimentally tested for various operational conditions and its accuracy was compared with previous mechanisms including GRI, Chevalier, and Konnov mechanisms14. These two mechanisms (GRI mech. And Leeds), unlike other mechanisms, have been developed only for modeling natural gas combustion. Other mechanisms are generally designed to simulate the combustion of hydrocarbons15–20. Several reduced mechanisms have been developed using GRI mech. to model methane combustion. Frenklach and Kazakov used the GRI-2.11 mechanism as a reference to introduce a reduced skeletal mechanism with 84 reactions and 19 species for methane combustion (DRM-19)21. Fotovat and Rahimpour reduced the GRI 3.0 mechanism by the direct relation graph with error propagation followed by the full species sensitivity analysis. This approach reduced the number of species from 53 to 2322. With the advancement of combustion technologies and fuel blending strategies, numerous chemical kinetic mechanisms have been developed simulating the combustion behavior of natural gas-based fuel blends, enabling better prediction of ignition characteristics, pollutant formation, and overall engine performance. In the technical literature, there are various mechanisms for the blended fuel of methane and n-heptane11, the blended fuel of hydrogen and methane23, the blended fuel of natural gas and C1 to C7 alkanes24, the blended fuel of methane and diesel25, the blended fuel of methane and syngas26, CO2 and methane27, etc. Although at the beginning of the development of chemical kinetics mechanisms, it seemed that the combustion chamber is a pool of radicals and species, but with the conducting more studies, it became clear that ions and electrons are also formed during hydrocarbons combustion. Therefore, new researches aimed at simulate the formation of ions during hydrocarbons combustion and their role in combustion characteristics28–30. The first ionic chemical kinetics mechanism to simulate ion current during methane combustion was presented by Pederson and Brown. The proposed mechanism had 5 positive ions, but no negative ions were considered in it31. Prager et al. modeled the ion chemistry methane – air flames. 11 ions and 69 ionic reactions were considered. In this mechanism, the method of ions formation from radicals is not known, and no connection between ions and stable species or radicals has been reported. In addition, the presented mechanism has not provided acceptable accuracy in comparison with the experimental data32. Chen et al. studied on ion chemistry during methane rich combustion according to the results H3O+ was the most important ion in slightly rich flames and C3H3+ was the most significant in very rich flames33. Knyazkov et al. studied on cations formation in near-stoichiometric burner-stabilized methane/oxygen/argon flames at atmospheric pressure. They revised the previously published mechanisms for cations formation and presented new paths. The results showed that the accuracy of the mechanism is improved using new cation base reactions34. A reduced mechanism for the prediction of methane/air flames impinged by external electric fields was presented by Renzo and Cuenot. This mechanism was composed of 26 species and 134 reactions. Thus, the mechanism guaranteed a significant reduction of the computational cost without penalties in the accuracy of electrified methane/air flames calculations35. López-Cámara et al. presented a reduced chemical kinetic model for methane-air combustion which included minor excited species and charged species. The mechanism included 45 species and 216 reaction and was validated for a two-dimensional flame geometry by comparison with detailed chemistry simulation results for species location and peak values, and experimental chemiluminescence location36. Cherepanov et al. improved ion chemistry in flames considering C3H3+ reaction pathways. They validated the mechanism against mass spectrometric measurements in non-sooting premixed flames of small aliphatic hydrocarbons. They also experimentally detected many CxHy+ cations not included in their mechanism and discussed the possible reaction pathways leading to CxHy+ production37. According to previous studies, the onset of ignition has been shown to coincide with the initiation of the ion current within combustion chambers. The main objective of this study is to develop a reduced ionic chemical kinetics mechanism capable of predicting the ignition timing during homogeneous methane combustion. To achieve this, the HCCI combustion chamber is modeled as a homogeneous reactor. Using the GRI-Mech mechanism as a baseline, the scheme is first reduced, and then supplemented with relevant ionic reactions and charged species to construct the final mechanism. Methodology In the present study at first the previously published multi zone model is coupled to the semi-detailed chemical kinetics mechanism and is validated against experimental data. Then the validated cases are used to specify the important reactions at the start of combustion (SOC), at the time that 50% of cumulative heat is released (CA50) and at the end of combustion (EOC) process (when the 90% of cumulative heat is released). The new reduced chemical kinetics mechanism is created using the specified important reactions and the species participating in them. At the next step the reduced chemical kinetics is coupled to multi zone model and is validated against experimental data. Finally the ions and related reactions are added to the chemical kinetics mechanism and the applicability of ionic chemical kinetics mechanism in prediction of SOC of the methane fueled HCCI engine is examined. Multi zone model Figure 1 illustrates the zone configuration in the developed multi-zone model, which consists of four distinct types of zones: crevice zone, boundary layer zone, outer zones, and core zone. The zone configuration of multi zone model. The crevice zone maintains a constant volume, equivalent to 3% of the clearance volume. This zone does not engage in heat transfer with other zones or the walls, resulting in a stable temperature that matches the wall temperature. Mass transfer occurs bidirectionally between the boundary layer zone and the crevice zone. The crevice zone refers to the narrow regions between piston rings and the cylinder wall. During the compression stroke, a portion of the in-cylinder gas escapes into this zone due to elevated pressure. Upon expansion, these trapped gases are released back into the combustion chamber. Because of the lower temperature in the crevice zone and limited flame penetration, hydrocarbons present in this region may not undergo complete combustion. As a result, they can either oxidize partially to form CO or remain unburned, contributing to unburned hydrocarbon (UHC) emissions. Therefore, incorporating the crevice zone into the multi-zone model and assigning a realistic volume to it plays a significant role in accurately predicting exhaust emissions. This inclusion helps capture the local conditions that affect post-combustion pollutant formation and strengthens the model’s environmental relevance. The boundary layer zone is the closest zone to the wall, forming a hollow cylindrical structure that remains in contact with the cylinder wall, cylinder head, and piston head. Its thickness varies proportionally with the cylinder height near the cylinder head and piston head, while maintaining a similar proportion relative to the bore near the cylinder wall. Consequently, its thickness fluctuates over time in the axial direction but remains constant in the radial direction. This zone interfaces with all other zones, facilitating both mass and heat transfer in multiple directions. Additionally, convective heat transfer occurs between this zone and all walls of the combustion chamber. The multi-zone model integrates a chemical kinetic mechanism to simulate combustion chemistry. The governing equations, including the first law of thermodynamics and chemical kinetics, are solved in a coupled manner for each zone. Equations (1) to (8) define these fundamental equations. where P, U, Q, W, and V represent the pressure, internal energy, heat transfer, work, and volume of the combustion chamber, respectively. The term denotes the production rate of the kth species in the ith zone. After solving the above equations, the pressure of the combustion chamber is calculated by using Eq. (9). As the equation shows for calculating the total pressure, the temperature and volume of all zones are used. where mi and Mwi are zonal mass and molecular weight of the zonal mixture. Further details of the model and equations used in mass transfer and heat transfer sub models are available in previously published studies38. In addition to simulation of closed cycle of the engine, the gas exchange process of HCCI engine is simulated using a single-zone thermodynamic model in which, in addition to solving energy and chemical kinetic equations, the equations of mass flow rates are solved at each time step. Inlet and outlet mass flow rates are calculated using the following Eqs. 39: where u and d indices refer to the upstream and downstream of the gas flow, CD is the discharge coefficients of the valves and AR is the effective area of the valve. Ionic chemical kinetics mechanism A detailed mechanism consisting of 53 species and 325 reactions has been implemented to develop the reduced mechanism10. One of the key approaches to reducing mechanisms is the identification and elimination of unessential reactions. Several methods have been proposed in the literature for this purpose, including: Comparing progress rates and Selecting reactions with lower relative progress rates compared to the basic reaction40, Sorting by progress rate: Prioritizing reactions based on their progress rates and selecting those with the lowest values41 Applying threshold criteria: Defining a user-specified threshold and selecting reactions with progress rates below this limit42 Among these methods, sorting reactions based on their progress rate has proven to be the most effective and reliable43. Using this approach, species involved in unessential reactions are removed from the mechanism. Various studies have employed this strategy for mechanism reduction44–46. In this study, a reduced ionic mechanism has been developed to predict HCCI engine performance. The process began by selecting different cases, followed by identifying essential reactions based on their progress rates at three critical combustion stages: the start of combustion, CA50, and end of combustion. To ensure an accurate reduced ionic mechanism, an optimal number of essential reactions must be selected carefully, avoiding the elimination of significant combustion pathways. Several reduced mechanisms have been explored, incorporating different numbers of essential reactions—ranging from 20 to 50 reactions (specifically, 20, 30, 35, 40, 45, and 50). The accuracy of each mechanism has been assessed using experimental data. Ultimately, the mechanism with the lowest number of reactions that still yields accurate results is presented as the optimal chemical kinetics mechanism. By choosing important reactions, the species that participated in these reactions were also selected and finally a mechanism with 48 reactions and 22 species was formed. The net progress rate of each reaction is calculated using the following equation: where kfi and kri are the forward and backward reaction rates of the ith reaction. The forward rates of the reactions are calculated by using Arrhenius coefficients according to the following equation: Thus, the equilibrium constant for a one-step reaction is equal to the forward rate constant divided by the reverse rate constant according to Eq. (13): where Kcj can be calculated using the following equations: where Kp and Kc are the equilibrium constant and G is the Gibbs function. In the next step, ionic reactions are added to the mechanism. The first ionic reaction is R49 in Table 2. Green and Sagden stated that this reaction is the first reaction in the ion formation chain47. Table 2The reactions of the ionic chemical kinetics mechanism.Reaction numberReactionsA (mole-cm-sec-K)b (-)E (cal/mole)R1O + CH3 = H + CH2O5.06E + 1300R2O + CH4 = OH + CH31.02E + 091.54327.7R3O2 + CH2O = HO2 + HCO1.00E + 14020,128.7R4H + 2O2 = HO2 + O22.08E + 19-1.20R5H + O2 + H2O = HO2 + H2O1.13E + 19-0.80R6H + O2 + N2 = HO2 + N22.60E + 19-1.20R7H + O2 = O + OH2.65E + 16-0.78575.3R8H + CH4 = CH3 + H26.60E + 081.65454.9R9H + CH2O(+ M) = CH3O(+ M)5.40E + 110.51308.4R10H + CH2O = HCO + H25.74E + 071.91379.8R11OH + H2 = H + H2O2.16E + 081.51726R122OH(+ M) = H2O2(+ M)7.40E + 13-0.40R132OH = O + H2O3.57E + 042.4-1061.8R14OH + HO2 = O2 + H2O1.45E + 130-251.6R15OH + H2O2 = HO2 + H2O2.00E + 120214.9R16OH + H2O2 = HO2 + H2O1.70E + 18014,799.6R17OH + CH4 = CH3 + H2O1.00E + 081.61570R18OH + CO = H + CO24.76E + 071.235.2R19OH + CH2O = HCO + H2O3.43E + 091.2-224.9R20OH + CH3OH = CH3O + H2O6.30E + 062754.8R212HO2 = O2 + H2O21.30E + 110-820.2R222HO2 = O2 + H2O24.20E + 1406038.6R23HO2 + CH3 = O2 + CH41.00E + 1200R24HO2 + CH3 = OH + CH3O3.78E + 1300R25HO2 + CO = OH + CO21.50E + 14011,875.9R26HO2 + CH2O = HCO + H2O25.60E + 0626038.6R27CH3 + O2 = O + CH3O3.56E + 13015,338R28CH3 + O2 = OH + CH2O2.31E + 12010,222.9R29CH3 + H2O2 = HO2 + CH42.45E + 042.52606.7R302CH3(+ M) = C2H6(+ M)6.77E + 16-1.2329.1R31CH3 + CH2O = HCO + CH43.32E + 032.82948.8R32CH3 + CH3OH = CH3O + CH41.00E + 071.55002R33HCO + H2O = H + CO + H2O1.50E + 18-18554.7R34HCO + M = H + CO + M1.87E + 17-18554.7R35HCO + O2 = HO2 + CO1.34E + 130201.3R36CH3O + O2 = HO2 + CH2O4.28E-137.6-1776.3R37O + CH3 = H + H2 + CO3.37E + 1300R38OH + HO2 = O2 + H2O5.00E + 1508720.7R39OH + CH3 = H2 + CH2O8.00E + 090.5-883.1R40CH2OH + O2 = HO2 + CH2O1.80E + 130453R41CH + H2 = H + CH21.08E + 140840R42O + CH2OH = OH + CH2O1.00E + 1300R43H + CH2OH = H2 + CH2O2.00E + 1300R44O + CH = H + CO5.70E + 1300R45O + CH2 = H + HCO8.00E + 1300R46O + CO(+ M) = CO2(+ M)1.80E + 1002385R47O + HCO = OH + CO3.00E + 1300R48O + HCO = H + CO23.00E + 1300R49CH + O = E- + HCO+2.50E + 1107092.9R50HCO+ + H2O = H3O+ + CO1.00E + 16-0.10R51H3O+ + E- = H2O + H2.29E + 18-0.50R52E- + O2 + N2 = O2- + N21.32E + 17-1-83R53H3O+ + E- = OH + H + H7.95E + 21-1.40R54OH + E- = OH-1.00E + 17-10 The reactions of the ionic chemical kinetics mechanism. The second ionic reaction is R5048. The next reaction is R51, where H3O+ ion turns into water. Aithal used this reaction to simulate the ionic current in the HCCI engines49. The next ionic reaction is the formation of the O2- according to R5248. The H3O+ can also convert into OH ion during the below reaction (R53)50: Finally, the following reaction (R54) is added to the mechanism49. The species of final ionic chemical kinetics mechanism is presented in Table 1. As it is shown in the table, the final version of ionic chemical kinetics mechanism contains 27 species. The reactions of mechanism are indicated in Table 2. The developed mechanism is accurate for methane HCCI combustion, the lean and low temperature combustion, and is not validated for other operational conditions. Table 1The species of the ionic chemical kinetics mechanism.SpeciesCH4 CO HO2 H2O H2 N2 O2 CO2 C2H6 AR CH3 H2O2 HCO CH2O CH3O CH3OH H OH O CH CH2 CH2OH HCO+ E- H3O+ O2- OH- The species of the ionic chemical kinetics mechanism. Results Four different engine operating conditions are selected and used to validate the accuracy of the multi zone model and reduced ionic chemical kinetics mechanism. The numerical in-cylinder pressure and engine exhaust emissions are compared with the experimental data. Experimental data was obtained from University of Alberta engine research facility. All experiments were performed using a Waukesha CFR (Cooperative Fuel Research) single cylinder research engine coupled to a DC motoring dynamometer. The engine was maintained at two constant speeds of 700 and 800 rpm and ran with an open throttle. The intake system included a 2.4 kW heater with a PID temperature controller to preheat intake air when required. Two types of fuel injectors, one for the n-heptane and the other for natural gas (NG), were located upstream of the intake valve to facilitate proper mixing. Air and fuel flow are crucial measurements for a precise determination of air/fuel ratio. A TSI model 4235–01-01 air mass flow meter was installed upstream of the engine before the pulsation damping barrel. Omega FMA21 series flow meters were used to measure the gaseous fuel mass flow rate. Two Max Machinery positive displacement flow meters, model 213–311, were used in the liquid fuel supply line. The control module of an AFS Sparrow-II engine was utilized to regulate the injection rate of each fuel separately or as a blend. External uncooled exhaust gas recirculation (EGR) line was connected to the intake after the heater and before the fuel injectors and was controlled by a manual butterfly valve. Intake gas was analyzed for the EGR fraction determination. A Vetronix PXA-1100 portable gas analyzer, which is capable of measuring different gases, was used in the intake system and EGR connection to the intake plenum to determine the carbon dioxide (CO2) concentration in the intake mixture. EGR was calculated using volume concentration measurement of CO2 upstream and downstream of the engine. EGR was calculated as: The lubricating oil was maintained at a constant temperature using a heater. A BEI rotary incremental encoder with a resolution of 0.1 crank angle degree (CAD) was used to monitor engine rotational speed and coordinate the pressure trace with respect to crank position. Cylinder pressure was measured with a Kistler 6043A, water-cooled pressure transducer in combination with a Kistler 507 charge amplifier. The pressure transducer was mounted in the cylinder wall close to the cylinder head. Experimental data were acquired using a personal computer running custom Labview software and using three high sampling rate NI PCI-MIO-16E1 data acquisition cards51,52. Table 3 shows the properties of the selected cases. As shown in the table, the equivalence ratio and the amount of EGR is different for every case. Table 3CFR engine operating conditions for four operating cases.Case numberRcAFR (Mass base)EGR (Mass base %)rpmPIVC (bar)TIVC (K)Volumetric Efficiency121.552.63218001.50466.3168.2221.538.1108001.51441.1182.5321.531.03338001.49478.2546.8421.551.8808001.527440.5593.3 CFR engine operating conditions for four operating cases. Figure 2 shows the experimental and numerical pressure curves for all of cases. Numerical data were obtained using the ionic and GRI mechanisms. The results obtained using GRI mechanism show that the multi zone model can properly predict the pressure inside the combustion chamber and subsequently the start of combustion and end of combustion. The results related to the ionic mechanism show that the ionic mechanism can predict in-cylinder pressure accurately too. The results of ionic mechanism is similar to the results of the GRI mechanism for some cases. Experimental and numerical in-cylinder pressure. Table 4 shows the experimental and numerical values of emissions exiting from the engine. According to the table, mechanism can accurately predict the amount of pollutant produced in the engine as well as engine performance. CO and CO₂ predictions from the model show good agreement with expected values, confirming the robustness of the oxidation pathways. In contrast, UHC predictions exhibit some discrepancies, which may be due to contributions from non-combustion sources such as lubricating oil. Additionally, the simplification of the chemical kinetic mechanism—especially the exclusion of less significant hydrocarbon species—can reduce the model’s accuracy in estimating total UHC levels. These factors are acknowledged and will be considered in future refinements. Table 4experimental and numerical engine exhaust emissions.EmissionCase 1Case 2Case 3Case 4Exp. CO2 (% by Vol.)5.517.686.153.16GRI CO2 (% by Vol.)5.527.456.363.14Ionic CO2 (% by Vol.)5.337.286.113.11Exp. CO (% by Vol.)0.0660.0560.0770.059GRI CO (% by Vol.)0.0660.0550.0780.059Ionic CO (% by Vol.)0.0630.0510.0680.059Exp. UHC (ppm)4806420258913476GRI UHC (ppm)4501410151123222Ionic UHC (ppm)4403411148163312 experimental and numerical engine exhaust emissions. Figure 3 shows the relative error of the ionic mechanism in engine emissions prediction. According to the figure, it is clear that the mechanism has underestimation for all emissions. The biggest error in CO2 prediction is 5.2%, in CO is prediction 11.68, and in UHC prediction is 18.24%. relative error of mechanism in engine emission prediction. Figure 4 plots the temperature for the case 1 using both of ionic and GRI mechanisms for the core zone and boundary layer zone. As shown in the figure, using the ionic mechanism, the temperature of the zones is lower than the values obtained using the GRI mechanism. This phenomenon is due to the presence of more reactions and releasing energy by them. In addition, the presence of ions causes the ignition to start earlier and prevents it to be delayed in the boundary layer and results in higher zonal temperature. Temperature curve for different zones using various mechanisms. Figure 5 shows the heat release rate and cumulative heat release for the second case, using various mechanisms. This figure clearly shows that the chemical reactions and subsequently heat release, while using ionic mechanism, starts faster. Another noticeable point is the oscillatory characteristics of the HRR. This is due to the nature of the multi zone models, which causes to the different start of combustion times in different zones. Heat release rate and cumulative heat release traces for case 1. In addition to in-cylinder pressure and temperature, the mass fractions of key species generated through the ionic mechanism should be compared with those predicted by the GRI-Mech mechanism. The hydrogen abstraction from the methane molecule represents the initial chemical reaction in the combustion process53. During this reaction, a hydrogen atom is removed from the fuel molecule, resulting in the formation of a hydrocarbon radical. Figure 6 illustrates the progress rates of the most significant hydrogen abstraction reactions within the ionic mechanism. As shown in Fig. 6, Reaction R2 (listed in Table 2) exhibits the highest contribution to methane hydrogen abstraction. the progress rates of methane H abstraction reactions in ionic 366 mechanism. Other important radical is HO2. During the combustion process, the HO₂ radical is initially formed via decomposition of the fuel according to reactions R3 to R6. It is subsequently consumed through reactions such as R14, R15, R16, R21, R22, R23, R29, and R38, leading to the formation of OH, H₂O₂, and H₂O. Figure 7 shows the progress rates of R3 to R6. According to the figure at first R3 (the following reaction) starts to work, but its progress rate is less than others. Progress rates of HO2 formation reactions. R6 (the following reaction) has the highest progress rates comparison to others. Hydrogen peroxide (H₂O₂) is another significant radical in the combustion process. Similar to hydroperoxyl (HO₂), it forms during initial reactions such as hydrogen abstraction and eventually converts to water. Additionally, H₂O₂ can be produced in termination reactions involving HO₂ and hydroxyl (OH) radicals. If the chamber temperature is sufficiently high, the radicals generated through these pathways readily transform into water. However, under low-temperature conditions, H₂O₂ may persist and remain as part of the exhaust mixture. The OH radical, likewise, is formed through hydrogen abstraction from the fuel molecule or via reactions between atomic hydrogen (H) and oxygen (O). It too ultimately transforms into water by the end of combustion. Inside the combustion chamber, OH, HO₂, and H₂O₂ radicals share similar formation and consumption pathways. All three emerge from initial and chain propagation reactions and eventually convert into water through termination steps. These radicals can interconvert during various intermediate reaction. Figure 8 visualizes the interactions among these radicals. As shown, Reaction R7 initiates earlier than the others, while Reaction R13 exhibits the highest progress rate, leading to the conversion of OH radicals into water. In contrast, Reactions R16, R21, and R22 demonstrate considerably lower rates compared to the other reactions. Progress rates of OH, HO2, and H2O2 related reactions. Figure 9 depicts the mass variation of H, OH, H2O, and H2O2 radicals within the combustion chamber for case 1. The figure indicates that the production and consumption patterns of the radicals are consistent across both mechanisms. The ionic mechanism accurately predicts the mass of crucial radicals. Although the absolute mass of H radicals is significantly lower than that of HO₂, H₂O₂, and OH, Fig. 9 shows that the GRI mechanism produces a slightly higher peak mass of H radicals than the ionic mechanism. This difference stems from the increased number of H-abstraction reactions in the GRI mechanism. However, due to the relatively low overall mass of H radicals, this variation does not have a considerable effect on the combustion process. Mass of important radicals inside the combustion chamber using both of mechanisms. In addition to H-based radicals, there are some other important radicals in the chamber. The most important C-based radical is CO. Figure 10 shows the variation of this radical in combustion chamber. This radical is usually formed by the dehydrogenization of the formyl radical (CHO) and turns into CO2 when the temperature of the chamber increases. Mass changes of CO for the case 1 using both of the mechanisms. O, CH and CHO are the radicals that play critical roles in production of ions and ion current in combustion chamber. Zettervall et al. showed that GRI mechanism can predict CH radicals during methane combustion accurately54. Figure 11 shows the in-cylinder CH, CHO and O calculated by GRI and ionic mechanisms. According to the figure ionic mechanism has a good accuracy comparison with GRI mechanism. Mass changes of CH, CHO, O for the case 1 using both of the mechanisms. In addition to the mentioned radicals, there are three other species that careful attention should be taken to their variation path. Fuel is the main source of the energy and its consumption during combustion process is important. CO2 and H2O are the main products of the combustion. Accurate prediction of the mass of this three species results in accurate prediction of engine output power. Figure 12 illustrates the mass variations of this species inside the combustion chamber. Mass variation of CO2, CH4 and H2O, calculated using both of the mechanisms. In addition to the chemical species, the mass variation of ions should be studied as well. Figure 13 show the mass changes of the positive ions; HCO+ and H3O+. As shown in the figure, the concentration of HCO+ is negligible in comparison to H3O+. Same result is reported by Aithal. In the mentioned study, the concentration of H3O+ reported is higher than the amount reported in this study. The reason for this can be the higher amount of hydrogen and oxygen atoms in the combustion chamber during the combustion of propane in comparison to the combustion of methane. Mass changes of HCO + for the second case. Figure 14 shows the mass variation of negative ions inside the combustion chamber. Figure 15 indicates mass of electron inside the combustion chamber. According to the mentioned figures, it is clear that the concentration of the OH- and O2- is almost the same but is lower than the concentration of the electrons. Electrons are formed and then consumed during the combustion. Rao and Damon reported similar results for methane and Aithal for propane48,49. Mass variation of the negative ions for case 1. Mass variation of electron for case 1. Comparison of the figures for the positive and negative ions show that H3O+ and OH- remain inside the chamber at the end of combustion process. While the electrons are almost completely consumed at the end of combustion process, the presented results by Sorokin et al. indicates that some of the positive and negative ions remain inside the chamber until exhaust valve opens55. Table 5 shows the time of SOC based on experimental data and the time that electron starts to form and ion current initiates. The data show that the developed ionic mechanism can be applied for estimation of the SOC in methane fueled HCCI combustion. The maximum error in prediction of the SOC using ion current is less than 0.09%. Figure 16 indicates the relative errors of the mechanism in prediction of the SOC according to the ion current. The results show that this modeling approach enhances the predictive capability for ignition timing and combustion phasing, thereby contributing to the design and control of advanced low-temperature combustion systems. By incorporating ionic reaction pathways into the kinetic scheme, the model facilitates improved diagnosis of combustion events through simulation of ion current signals. Such integration enables the potential deployment of ion current–based control strategies, linking chemical kinetics to practical feedback systems for real-time engine management. In contrast to conventional single-zone or global models, the spatial resolution of the proposed framework captures in-cylinder reactivity variations, providing valuable insights into combustion stability, heat release uniformity, and emission formation. These capabilities are critical for broadening the operational limits of HCCI engines and mitigating issues such as knock and misfire. Comparative analyses between the GRI-Mech mechanism and the ionic mechanism further demonstrate the trade-off between computational load and diagnostic precision, offering guidance for mechanism selection in engine-specific optimization. Moreover, the simulation results support early-stage design decisions without reliance on extensive experimental campaigns, particularly for unconventional fuel candidates. The proposed model is adaptable to alternative fuel compositions, making it a flexible tool for future research on fuel-agnostic HCCI operation. This aligns with global objectives toward decarbonization and supports the development of clean combustion technologies. Table 5SOC and start of electron formation times.TimeCase 1Case 2Case 3Case 4θ (experimental SOC)357.1354.9355.1354.2θ (start of ion current)356.8354.8355.1354.0 SOC and start of electron formation times. relative error in prediction of SOC. Conclusion A novel reduced ionic chemical kinetics mechanism for simulation of the combustion of the methane fuel in HCCI engines is presented in the current study. Prediction of the time of the start of combustion is the main purpose of the study. The mechanism contains 27 species and 54 reactions. The main results are: The ionic mechanism can predict in-cylinder pressure accurately. The ionic mechanism can predict in-cylinder pressure accurately. The mechanism has an appropriate accuracy in predicting the species inside the combustion chamber. The mechanism has an appropriate accuracy in predicting the species inside the combustion chamber. The mechanism has good accuracy in prediction of the time of SOC. The mechanism has good accuracy in prediction of the time of SOC. The mechanism can predict engine exhaust CO and CO2 accurately. The mechanism can predict engine exhaust CO and CO2 accurately. According to the results electron is consumed completely inside the combustion chamber, but other ions remain. According to the results electron is consumed completely inside the combustion chamber, but other ions remain. Acknowledgements The authors would like to thank the INSF for the support of this study. Abbreviations Area (m2) Effective flow area (m2) Specific heat constant at constant volume (J/kgK) Discharge coefficient Enthalpy (J/kg) Convection heat transfer coefficient (J/m2. s. K) Thermal conductivity (J/m. s. K) Equilibrium constant Rate of forward reaction Rate of forward reaction Mass (kg) Molecular weight Number of species Pressure (Pa) Heat (J) Progress rate of reactions Universal ideal gas constant (J/mol.K) Temperature(K) Time (s) Internal energy (J) Specific internal energy (J/kg) Volume (m3) Stoichiometric constant of each species in each reaction Work (J) Mass fraction Greek letters Ratio of specific heats Crank angle position (Degree) Density (kg/m3) Molar rate of production (mole/m3s) Subscripts Boundary layer Conductive heat transfer Convective heat transfer Downstream I th zone J th species K th reaction Reference condition, IVC Transferred Upstream Author contributions Authors Contributions EN: Study conception and design, Data analysis and interpretation, Drafting of the article, Critical revision of the article AMI: Data collection, Drafting of the article DH: Data collection, Drafting of the article. Data availability Data is available in the manuscript file. Declarations Competing interests The authors declare no competing interests. Footnotes Publisher’s note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations. References Associated Data Data Availability Statement Data is available in the manuscript file.