Native GaN/GaOx Heterostructure Platform for Wafer-Scale Integration of High-Performance Complementary Transistors Authors: Jinhua Liang, Chi Liu, Yuning Wei, Shun Feng, Yun Sun, Yutaka Ohno, Hui-Ming Cheng, Dong-Ming Sun Published: 2025 ABSTRACT The drive for complementary transistors with ultra-steep subthreshold swing (SS) and minimal power consumption has intensified interest in integrating low-dimensional semiconductors with wide-bandgap materials, as silicon scaling approaches its physical limits in the post-Moore era. A central bottleneck, however, lies in dielectric/semiconductor interface engineering: existing strategies based on van der Waals transfer or nonnative dielectric deposition compromise interface quality, wafer-scale uniformity, and process compatibility, preventing practical large-scale integration. Here, we demonstrate a previously unexplored in situ oxidation strategy that directly forms a high-κ gallium oxide (GaOx) dielectric on heavily doped n-type gallium nitride (GaN) substrates, enabling high-performance, energy-efficient complementary inverters based on n-type molybdenum disulfide (MoS2) and p-type carbon nanotube transistors. Leveraging the excellent dielectric properties of the GaN/GaOx heterostructure, MoS2 field-effect transistors achieve an interface trap density of 1.18 × 1011 cm−2 eV−1, an SS at the thermionic limit of 60 mV dec−1, an on/off ratio above 108 at 0.87 V, and a voltage gain of 134.5 at 2 V for inverters. These results establish GaN/GaOx as a native, scalable, and complementary metal-oxide-semiconductor-compatible integration platform, offering a transformative route toward wafer-scale, low-power electronics in the post-Moore era. Introduction In the post-Moore era, as the scaling of traditional silicon-based transistors approaches its fundamental physical limits, severe short-channel effects lead to sharply increased off-state current and power dissipation, which severely constrain the further enhancement of integrated circuit performance [1–5]. The development of novel complementary transistors with an ultra-steep subthreshold swing (approaching the theoretical limit of 60 mV dec−1) and ultralow static power consumption has consequently emerged as a critical challenge. The wide-bandgap semiconductor gallium nitride (GaN), known for its high breakdown field strength, high electron mobility, and excellent thermal stability, provides a highly promising platform for heterogeneous integration with emerging low-dimensional materials such as molybdenum disulfide (MoS2) and carbon nanotubes (CNTs), whose atomic-scale thickness enables superior gate controllability and suppressed off-state leakage current. This material system presents a compelling route to simultaneously achieve superior gate controllability, high carrier mobility, and intrinsically low power consumption, opening new possibilities for next-generation integrated electronics [6–10]. However, a major bottleneck in this integration scheme lies in the poor control over the interface quality between low-dimensional materials and dielectric layers [11–13]. Conventional atomic layer deposition (ALD) of high-κ dielectrics (Al2O3 and HfO2) often suffers from nonuniform nucleation on 2-dimensional (2D) material surfaces due to the lack of surface dangling bonds, leading to inferior interface quality that degrades subthreshold characteristics and operational stability at scaled equivalent oxide thickness (EOT) [14,15]. To address this interfacial challenge, several integration strategies have been explored, including transferred van der Waals dielectrics (such as HfOx and h-BN) [16–18], molecular buffer interlayers (such as Sb2O3 and 3,4,9,10-perylene-tetracarboxylic dianhydride [PTCDA]) [19–21], and epitaxially grown crystalline dielectrics (such as CaF2) [22] via molecular beam epitaxy. While these approaches have yielded quantifiable improvements in interface quality, their practical application is often constrained by inherent technical limitations, such as difficulties in achieving thickness uniformity in van der Waals dielectrics and the incompatibility of high-temperature epitaxial growth processes with standard CMOS technology, which hinders the wafer-scale uniformity and process compatibility required for reliable large-scale integration in post-Moore electronics. Here, we propose an innovative strategy of in situ growth: through controlled thermal oxidation of heavily doped n-type GaN substrates, a high-quality, high-κ gallium oxide (GaOx) dielectric layer is directly generated on the GaN surface. This method leverages the innate properties of GaN to construct a high-performance GaN/GaOx heterostructure platform with excellent dielectric properties. MoS2 field-effect transistors (FETs) fabricated on this GaOx dielectric show an interface state density as low as 1.18 × 1011 cm−2 eV−1 and a small subthreshold swing of 60 mV dec−1. The GaN/GaOx heterostructure platform is also compatible with high-performance p-type CNT FETs. Fabricated complementary inverters integrating n-type MoS2 and p-type CNT transistors achieve a maximum voltage gain of 134.5 at a supply voltage of 2 V, which demonstrates the potential of this technology for future low-power integrated circuits. Results Device design and characterization Figure 1A shows the schematic diagram of an MoS2 transistor with a back-gate stack of MoS2/GaOx/GaN, where the GaOx dielectric is prepared by thermal oxidation of the GaN substrate. A 30-nm-thick Al2O3 is used as the isolation layer. The Ti/Al/Ti/Au stack serves as the gate electrode and enables an ohmic contact with the GaN substrate (Fig. S1), while graphene is used as source and drain electrodes [23]. Detailed fabrication processes are shown in Figs. S2 and S3. The cross-sectional transmission electron microscopy (TEM) image of the gate stack clearly reveals a uniform 3.2-nm-thick GaOx dielectric with atomically flat surfaces (Fig. 1B), while the elemental mapping (Fig. 1C) and the Raman spectra (Fig. S4) collectively confirm the gate stack composition. This high-quality GaN/GaOx heterostructure platform enables exceptional MoS2 transistor performance, including a large on/off ratio over 108, a small gate leakage current below 100 fA, and a near-ideal subthreshold swing (SS) of 60 mV dec−1 in double-sweep transfer characteristic curves (Fig. 1D). Design and fabrication of device. (A) Schematic diagram of the MoS2 transistor. (B) Cross-sectional TEM image of the MoS2/GaOx/GaN heterostructure showing a high-quality interface between MoS2 and GaOx (left scale bar: 100 nm, right scale bar: 2 nm). (C) TEM image with corresponding elemental mappings of Ga, N, O, Mo, and S, respectively (scale bar: 5 nm). (D) Double-sweep transfer characteristic curves of the MoS2 transistor with a constant Vds of 1 V, featuring a channel length of 20 μm and a width of 5 μm. High-κ GaOx dielectric layer The GaOx dielectric layer is fabricated through thermal oxidation of GaN in an oxygen-rich environment. During this process, oxygen atoms progressively replace nitrogen atoms in the surface layers, forming GaOx with tiny-grained oxide while releasing NOx gas (Fig. 2A and B) [24–26]. Importantly, this thermal oxidation process enables wafer-scale production of GaOx dielectrics (Fig. 2C). X-ray photoelectron spectroscopy (XPS) is used to analyze the chemical composition of the GaOx film. The experimental Ga 2P3/2 core-level spectrum is well-fitted by both Ga-N and Ga-O bonding configurations (Fig. 2D), confirming the formation of Ga-O components in the dielectric while residual Ga-N signatures remain detectable due to the ultrathin nature of the dielectric [27,28]. Consistent conclusions are obtained from the Ga 3d core-level spectrum (Fig. S5). Complementary measurements of secondary ion mass spectrometry (SIMS) further verify that the dielectric layer consists of pure Ga-O bonding, with negligible Ga-N content (Fig. S6). Atomic force microscopy (AFM) characterization demonstrates that the GaOx dielectric exhibits exceptional uniformity and flatness at the micrometer scale, showing no discernible surface protrusions or holes (Fig. 2E). The high-quality interface enables the GaOx dielectric to achieve complete insulation below 2 V (Fig. 2F and Fig. S7). Preparation and property of GaOx dielectric. (A) Schematic diagram of GaOx formation mechanism via thermal oxidation of the GaN (0001) substrate. (B) Cross-sectional TEM image of the in situ grown GaOx dielectric on GaN substrate (scale bar: 2 nm). (C) Optical image of a 2-inch wafer with uniform GaOx film (scale bar: 1 cm). (D) High-resolution XPS spectra of Ga 2P3/2 core level for the GaOx dielectric (prepared at 300 °C for 60 min), fitted by Ga-N (low-intensity) and Ga-O (high-intensity) bonding states. (E) AFM image of the GaOx dielectric (scale bar: 1 μm) and corresponding height profile. (F) Current leakage and breakdown characteristics of the GaOx film. (G) Current–voltage (I–V) characteristics of the GaOx layer. Inset: Schematic diagram of the setup for the peak force tunneling AFM (PF-TUNA) measurement. (H) Schottky emission model fitting of I–V data for dielectric constant extraction. The dielectric constant of the GaOx dielectric is characterized by an AFM-based PeakForce TUNA technology, which has been widely used to measure the dielectric properties of ultrathin materials [29,30]. A schematic diagram of the measurement is illustrated in Fig. 2G. Current–voltage (I–V) characteristics are measured by applying a sweeping bias voltage to the sample. The curve demonstrates that the GaOx film is completely insulated below 7.7 V, and the breakdown point where the current rises above the machine noise level is about 9.3 V. Using the Schottky emission model to fit and analyze the results, we calculate a dielectric constant of 11.2 for the GaOx layer, corresponding to an EOT of 1.1 nm (Fig. 2H). In addition, repetitive measurements across multiple locations on the same sample and different samples are conducted, and similar results confirm the excellent uniformity of the GaOx dielectric (Fig. S8). We also conduct Au/GaOx/GaN MOSCAP measurements with double sweep at different frequencies and scan rates, and the observation of negligible hysteresis under all test conditions confirms the exceptional stability and reliability of the GaOx dielectric layer (Fig. S9). The effects of oxidation temperature (200 to 500 °C) and time were examined to clarify their role in the dielectric formation mechanism [31,32]. XPS analysis shows progressive shifts of the Ga 2P3/2 and Ga 3d peaks toward higher binding energies by 0.14 and 0.16 eV (Fig. S10) with concurrent bandgap reduction from 4.9 to 4.8 eV (Fig. S11), confirming temperature-dependent oxidation. The insulation performance of the GaOx dielectric is highly dependent on the thermal activation process. Insufficient treatment (low temperature/short time) results in incomplete oxidation, whereas excessive conditions (high temperature/prolonged time) generate numerous grain boundaries. These grain boundaries serve as leakage pathways for carriers, and both extremes ultimately degrade the insulation properties, as evidenced in Figs. S12 and S13. High-performance MoS2 transistor Owing to the high-quality interface and small EOT of the GaOx dielectric, the MoS2 transistors fabricated on a GaN/GaOx heterostructure platform exhibit excellent electrical characteristics, including high on/off current ratios at different drain voltages, especially a high on/off current ratio over 108 under an operating voltage of 0.87 V when Vds = 0.5 V (Fig. 3A and B). Similar excellent performance is also demonstrated in other devices (Fig. S14). Excellent performance of MoS2 FET fabricated on a GaN/GaOx heterostructure platform. (A) Output characteristic curves of MoS2 transistor with Vgs increasing from −0.5 to 1 V at a step size of 0.5 V. (B) Transfer characteristic curves of MoS2 transistor at different drain voltages, featuring a channel length of 7 μm and a width of 5 μm. (C) Double-sweep transfer characteristic curves of the MoS2 transistor at various sweep rates with a constant Vds of 0.5 V. (D) Subthreshold swing (SS) and interface state density (Dit) of our device in comparison with transistors fabricated by various approaches [18,21,22,34–39]. (E) Operating voltage and on/off ratio of our device in comparison with MoS2 transistors fabricated by various approaches [16,19–21,37,40–43]. Additionally, negligible hysteresis (~7 mV) is observed in the reverse gate voltage scan, which is slightly influenced by the sweeping speed (Fig. 3C), signifying the high-quality MoS2/GaOx interface with a low interface state density (Dit). The Dit can be evaluated using the equation [17,33]:Dit=CGqqSSkBTIn10−1(1)where CG is the capacitance per unit area of the gate, SS is the subthreshold swing, q is the elementary charge of the electron, kB is the Boltzmann constant, and T is the temperature in kelvin. A Dit as low as 1.18 × 1011 cm−2 eV−1 is evaluated. Furthermore, both the multiple switching cycle tests and the bias stress stability tests confirm the superior interface quality of the GaOx dielectric layer, as evidenced by a negligible threshold voltage shift (ΔVth < 10 mV) in the MoS2 transistors (Figs. S15 and S16). To benchmark the performance of our device, the key parameters such as Dit, SS, and on/off ratio are compared with the state-of-the-art MoS2 transistors employing various dielectric integration strategies (Fig. 3D and E). These strategies encompass several established methods, including direct ALD of Al2O3 or ZrO2, molecular-layer-assisted ALD with Sb2O3 or PTCDA, material oxidation, and the transfer of van der Waals dielectrics like BN or SrTiO3. In contrast, the GaN/GaOx heterostructure platform adopted in this work exhibits an ultralow Dit (1.18 × 1011 cm−2 eV−1), enabling superior device characteristics: a near-ideal subthreshold swing of 60 mV dec−1 and a high on/off ratio of 108 at ultralow operating voltages. These results underscore the exceptional interface quality of the MoS2/GaOx heterostructure, highlighting its marked potential for future low-power 2D device applications. MoS2 and CNT transistor arrays To investigate the potential applications of the GaN/GaOx heterostructure platform, we have fabricated the FET arrays based on large-area monolayer CVD MoS2 and wafer-scale GaN/GaOx heterostructure platform (Fig. 4A), following similar fabrication procedures with the transistors of exfoliated MoS2 (further details are provided in Fig. S2). The CVD MoS2 FETs exhibit excellent consistency in transfer characteristic curves at different channel lengths (Fig. S17) under a Vds of −0.5 V (Fig. 4B and C). MoS2 and CNT transistor arrays. (A) Optical image of CVD MoS2 transistor arrays fabricated on a GaN/GaOx heterostructure platform (scale bar: 0.5 cm). Inset: Schematic diagram of the CVD MoS2 transistor. (B and C) Transfer characteristic curves of 30 MoS2 transistors with the same channel length (B), and their statistics of SS and on/off ratio (C). (D and E) Transfer characteristic curves of 30 CNT transistors with the same channel length (D), and their statistics of SS and on/off ratio (E). (F) Statistical distribution of Vth for 30 CVD MoS2 FETs and 30 CNT FETs. While the MoS2 transistor arrays exhibit excellent n-type characteristics (on/off ratio over 107, subthreshold swing ~ 60 mV dec−1), it is equally imperative to realize high-performance p-type devices for the development of complementary logic architectures. One-dimensional (1D) CNTs, with their inherent hole-transport superiority and compatibility with low-temperature processing, serve as an ideal counterpart to match with n-type MoS2 (Fig. S18). Additionally, CNT films are compatible with uniform and scalable fabrication processes, enabling the deposition of high-quality, highly homogeneous thin films over large areas. This capability provides a reliable material foundation for the mass production of high-performance electronic devices (Fig. S19). Utilizing this GaN/GaOx heterostructure platform, we successfully fabricated CNT transistor arrays and conducted comprehensive electrical characterization of 30 devices with identical channel lengths (L = 30 μm) at Vds = −1 V (Fig. 4D and E). The CNT transistors show improved gate control (Fig. S20) with GaOx dielectric. Statistical analysis of threshold voltages (Vth) for both MoS2 and CNT transistors exhibits narrow Gaussian distributions (Fig. 4F), confirming the excellent uniformity and reproducible fabrication of the GaN/GaOx heterostructure platform with different semiconductor materials. Complementary inverter As the fundamental building block of CMOS circuits, the voltage transfer characteristics (voltage gain) of inverters are intrinsically governed by the electrostatic control capability of the dielectric layer. In this work, we successfully employed high-κ GaOx as the gate dielectric to achieve co-integration of n-type MoS2 and p-type CNT transistors on a GaN/GaOx heterostructure platform. This strategy demonstrates excellent electrical matching performance and enables the fabrication of complementary inverters (Fig. 5A and B). The voltage transfer characteristic (Vout−Vin) and voltage gain (dVout/dVin) are measured by sweeping the input voltage (Vin) from −2 to 2 V under different supply voltages (Vdd), as depicted in Fig. 5C and D, respectively. Utilizing the superior gate control of GaOx dielectric, the inverter exhibits sharp switching near Vin = 0 V across all Vdd values with Vout infinitely close to Vdd or 0 V. Notably, a maximum voltage gain of 134.5 is achieved at Vdd = 2 V. The rapid switching response provides compelling evidence for superior gate control enabled by our GaN/GaOx heterostructure platform. Complementary inverter fabricated with n-type MoS2 FET and p-type CNT FET. (A) Schematic diagram and optical image of the inverter fabricated on a GaN/GaOx heterostructure platform (scale bar: 10 μm). (B) Transfer characteristic curves of MoS2 and CNT transistors. (C) The voltage transfer characteristics of the inverter at various supply voltages. (D) Corresponding voltage gains. Furthermore, dynamic switching cycle tests were conducted on the fabricated inverters. The results indicated that the output voltage amplitude and waveform maintained excellent consistency over consecutive cycles, demonstrating remarkable operational stability (Fig. S21). Further benchmarking against other state-of-the-art complementary inverters reported in the literature revealed that our devices exhibit competitive performance metrics, providing strong evidence for the practical reliability of the proposed platform in integrated circuits (Fig. S22). Discussion In conclusion, we have developed an excellent wafer-scale high-κ GaOx dielectric through the thermal oxidation of GaN and leveraged it for the integration of 2D and 1D materials. MoS2 FETs fabricated on a GaN/GaOx heterostructure exhibit excellent performance, including an ultralow Dit of 1.18 × 1011 cm−2 eV−1 and a high on/off current ratio of 108 under a small operating voltage of 0.87 V. The heterostructure platform simultaneously supports the fabrication of both CVD-grown monolayer MoS₂ and CNT FET arrays, demonstrating excellent reproducibility across multiple transistors. Complementary inverters integrating n-type MoS2 and p-type CNT transistors achieve a record-high voltage gain of 134.5 at Vdd = 2 V. Our work presents a versatile and CMOS-compatible heterostructure integration platform that can unlock the potential of 2D/1D materials for advanced high-performance complementary electronics. Materials and Methods Fabrication of a GaN/GaOx heterostructure The heavily doped n-type GaN substrate (0001) (resistivity: <0.05 Ω cm) was cleaned sequentially in acetone and isopropanol for 5 min each to remove surface contaminants, followed by diluted HF cleaning for 30 s. The GaOx dielectric was prepared by thermal oxidation in an oxygen atmosphere at 300 °C for 60 min. Fabrication of MoS2 FETs on a GaN/GaOx heterostructure platform After ultrasonic cleaning and acid cleaning, a photoresist layer (LOR3A) was spin-coated at 2,000 revolutions per minute (rpm) for 60 s on the GaN substrate and baked at 190 °C for 5 min. Then, another photoresist layer (S-1813) was spin-coated at 4,000 rpm for 60 s on the substrate and baked at 120 °C for 2 min. An undercut structure was fabricated by photolithography and developing processes. The ohmic contact between the metal electrodes and the GaN substrate was formed using a Ti/Al/Ti/Au (20/30/20/30 nm) stack deposited by electron-beam evaporation and lift-off, with subsequent annealing at 700 °C for 30 s in N2. Then, the Al2O3 layer (30 nm thick) was deposited on the substrate via ALD at 150 °C, using trimethylaluminum (TMA) and water as precursors. Metal contacts (Ti/Au: 5/50 nm) of drain and source electrodes were deposited on the Al2O3 layer. Then, Al2O3 layer was patterned by photolithography and etched with H3PO4 at 70 °C for 3 min, leaving windows on the GaN substrate for GaOx dielectric formation. A few-layer MoS2 flake was mechanically exfoliated from a bulk crystal and transferred onto a polydimethylsiloxane stamp. It was then released onto the target GaOx dielectric using an electronic van der Waals transfer station. With the same method, we transferred 2 graphene flakes onto the substrate to connect MoS2 and the Ti/Au and completed the fabrication of the FET. Fabrication of CVD MoS2 and CNT FET arrays on a GaN/GaOx heterostructure platform The fabrication of CVD MoS2 and CNT FET arrays followed initial steps similar to the exfoliated MoS2 transistors. After establishing ohmic contacts to the GaN substrate, an Al2O3 layer (30 nm thick) was deposited and patterned via photolithography and H3PO4 etching, followed by GaOx dielectric formation in the exposed regions. For MoS2 FETs, a centimeter-scale continuous monolayer CVD MoS2 film was first transferred onto the prepatterned substrate. Then, the excess MoS2 film was removed by oxygen plasma treatment with an oxygen flow rate of 180 standard cubic centimeters per minute (sccm) for 2 min. Metal contacts (Ti/Au: 5/50 nm) of drain and source electrodes were deposited on the MoS2 film using photolithography and electron beam evaporation. For CNT FETs, the drain and source electrodes (Ti/Au: 5/50 nm) were first deposited on Al2O3. A semiconducting CNT film was then deposited from a toluene solution at 60 °C over 2 h, followed by sequential cleaning in toluene and isopropyl alcohol at 80 °C for 10 min each. Finally, CNT channels were patterned and etched using oxygen plasma treatment at 200 W with an oxygen flow rate of 180 sccm for 2 min. Fabrication of complementary inverter The complementary inverter is implemented with an n-type and a p-type transistor configured in a complementary architecture. First, the p-type CNT FET was fabricated following the standard processes described above. Subsequently, a MoS2 flake was transferred onto the GaOx dielectric adjacent to the CNT device, followed by deposition of source/drain electrodes (Ti/Au: 5/50 nm) to complete the n-type MoS2 FET. Finally, the p-CNT and n-MoS2 FETs were electrically interconnected to form a complementary inverter. Characterization The fabricated devices were characterized using an optical microscope (Nikon ECLIPSE LV100ND), TEM (FEI Talos F200X), XPS (Thermo VG Scientific ESCA LAB250), AFM (Bruker Dimension Icon AFM), micro-Raman analyzer (Jobin Yvon HR800 with 532-nm laser excitation), SIMS (ION TOF-SIMS 5), and x-ray diffraction. The electrical performance of the transistors was measured using a semiconductor analyzer (Agilent B1500A equipped with a B1500A-A20 capacitance measurement unit) and probe station (Cascade Microtech, 150-PK-PROMOTION).