Chemical structural variations of asphaltene during solvent swelling characterized by 13C nuclear magnetic resonance and X-ray diffraction Authors: Shuyong Shi, Tian Liang, Xiaohui Lin, Yunpeng Wang, Yanrong Zou, Ping’an Peng Published: 2025 ABSTRACT AbstractThe asphaltene plays an important role in hydrocarbon retention and expulsion processes. In this study, the 13C nuclear magnetic resonance and X-ray diffraction were employed to investigate adsorption capacity and chemical structural variations of the asphaltene during the solvent swelling. The saturates and aromatics mainly accumulate between the aliphatic carbon chains in asphaltenes with both long and short aliphatic chains. However, it is difficult for the aromatics to accumulate between aromatic carbon chains in short aliphatic chain asphaltene. The aliphaticity of kerogen, solid bitumen and asphaltene primarily controls their adsorption capacity of saturates, whereas their adsorption capacity of aromatics is influenced by the complex interplay of aliphaticity, aromaticity, and thermal maturity. With increasing of thermal maturity, the structures of three organic macromolecules evolve to be more stable structures, resulting in a smaller and more consistent saturation swelling ratio for aromatics. Furthermore, two new methods are established to calculate the masses of saturates and aromatics adsorbed by asphaltene and kerogen. Asphaltene is the main product of kerogen cracking in the low-to-moderate maturity stage and has a strong adsorption capacity on liquid hydrocarbons. Its adsorption capacity needs to be incorporated into future studies on the hydrocarbon expulsion from shale.Keywords: Adsorption ability, Chemical structure, Organic macromolecule, Molecular modelSubject terms: Chemistry, Energy science and technology, Materials science Introduction The kerogen preferentially adsorbs high-molecule hydrocarbons due to their high retention capacity during hydrocarbon retention and expulsion processes, whereas low-molecule hydrocarbons can easily expel from source rocks1–3. It has been demonstrated that the degradation of kerogen results in the generation of significant quantities of asphaltenes, especially in the low-to-moderate maturity stage with thermal maturity (Ro%) lower than 1.0%4. However, the role of asphaltene in hydrocarbon retention and expulsion has not been fully recognized4–6. As one of organic macromolecules, the asphaltene exhibits relatively high-molecule weight (500–2000 g/mol), complex chemical structure, and strong polarity, which are analogous to those of kerogen7–10. The asphaltene also has the capacity to absorb certain saturates and aromatics in a manner similar to the kerogen, which is attributed to its special chemical structures. It is important to emphasize that although the swelling of kerogen and solid bitumen has been studied, the in-situ chemical structural changes of asphaltene during swelling remain unknown, which is the key issue of this study. Interactions between the asphaltene and liquid hydrocarbons are vital in the study of the hydrocarbon generation and expulsion processes of source rocks. The swelling of solid organic matter is an important phenomenon in the interactiosn between solid and liquid organic matters. It is a classical method for studying hydrocarbon adsorption capacity of solid organic matter11–13. Previous studies mainly focused on the solid organic matter changes in volume and the ability to dissolve hydrocarbons during solvent swelling14–17. Further research has yielded several studies on the chemical structure variations of organic macromolecules, including kerogen11,18–20, solid bitumen21 and coal20,22 during this process. Furthermore, the interactions between the asphaltene and liquid hydrocarbons also occur during the solvent swelling, representing a key process relevant to the hydrocarbon retention and expulsion. The asphaltene is not only the product of kerogen cracking, but also plays a critical role in the adsorption of liquid hydrocarbons during solvent swelling. However, this aspect was generally overlooked in previous swelling experiments. Consequently, chemical structural variations of asphaltene and its adsorption capacity on the liquid hydrocarbons during this process are not yet fully elucidated. Numerous analysis techniques have been developed to characterize chemical structures of organic macromolecules. These includ the solid-state 13C nuclear magnetic resonance (NMR), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), and Fourier transform ion cyclotron resonance mass spectrometry (FT-ICR-MS). Liang et al.19–21 developed the method that integrates 13C NMR and XRD analysis technologies. This method has been successful to characterize the changs in chemical structures of solid bitumen, kerogen and coal during solvent swelling. This method is also employed in the investigation of chemical structural variations of asphaltene during the swelling process in this paper. The chemical structure of asphaltene is of pivotal importance in terms of its capacity to adsorb liquid hydrocarbons, and its variations during solvent swelling need to be well studied. To address this question, The solvent swelling experiments serve as a classical methodology for investigating the interactions between the asphaltene and liquid organic matter17,23–25. In this study, three asphaltene samples were prepared to conduct solvent swelling experiments. Prior to the swelling experiments, the structural properties of three samples were also investigated using the solid-state13C NMR technology, providing basic structural information of three asphaltene samples. The n-hexadecane (C16H34) and n-heptylbenzene (C13H20) were selected as the swelling solvents to represent the swelling behaviors of saturated and aromatic hydrocarbons, respectively. Following the swelling experiments, the XRD analysis was employed to acquire the structural parameters of swollen asphaltene, such as the interlayer spacing of amorphous carbon in aliphatic carbon (dγ) and the microcrystals in the chemical structures (d002). The purposes of this study are: (1) to reveal the adsorption capacity of asphaltene on liquid hydrocarbons; (2) to investigate chemical structural variations of asphaltene during solvent swelling process; and (3) to establish methods to calculate the masses of saturates and aromatics adsorbed by asphaltene and kerogen under different thermal maturities. Samples and methods Preparation of asphaltene samples Three crude oils are normal and low mature oils, with a higher asphaltene content. The higher content of asphaltene shows that the influence of its adsorption on the saturates and aromatics are not neglectable. Sample KL was from the Kelamayi City, Tarim Basin, sample LG was from the Tarim Basin (Lunnan County, Aksu Autonomous Prefecture, Xinjiang province), and sample SC was from the Cambrian Changjianggou Formation of northwestern Sichuan Basin (Guangyuan City). The crude oils were dissolved in excess n-hexane (C6H14) and thoroughly mixed by an ultrasound machine. The mixed solutions were then subjected to centrifugation at a speed of 3,500 rpm. Subsequently, the asphaltene fractions were precipitated at the bottom of the solutions, and the supernatant solutions were removed by a dropper. This process was repeated approximately 5 times until the supernatant liquor was colorless. The asphaltene powder samples were finally obtained after dying at 60 ℃ for 12 h. Rock–Eval analysis The basic pyrolysis of three asphaltene samples was analyzed on the Rock–Eval VI instrument. The powder samples (ca. 5–10 mg) were heated to 300 ℃ to obtain S1 (free hydrocarbons). The samples were then pyrolyzed from 300 to 600 ℃ at the heating rate of 25 ℃/min to obtain S2 (pyrolysis hydrocarbons), S3 (organic carbon dioxide) and Tmax (temperature of peak S2 maximum). Subsequently, the total organic carbon (TOC) and hydrogen index (HI) can be calculated according to these parameters26. Solid-state 13C nuclear magnetic resonance analysis The solid-state 13C NMR technology was used to characterize the structural properties of three asphaltene samples. The 13C NMR experiments were performed using a Bruker AVANCE III 400 MHz NMR instrument equipped with a 4 mm dual-resonance probe, with an analysis speed of 14,000 Hz. Swelling experiments The n-hexadecane (C16H34) and n-heptylbenzene (C13H20) were selected as the swelling solvents to represent the swelling behaviors of saturated and aromatic hydrocarbons, respectively19. The swelling experiments were performed at 20 ℃ in the laboratory to reduce the volatilization of organic solvents. Two groups of swelling experiments were designed using the two organic solvents. The asphaltene samples were weighed and added to a clean 4 mL glass bottle with each point having two such bottles. The quantities of two solvents were subsequently added to the two bottles of each point, respectively, with the percentage of the solvents increasing regularly. The percentage and the weight of the two solvents, as well as the corresponding swelling ratio of each point are presented in Table 1. Table 1The swelling ratio, proportion of solvent and adsorption mass of three asphaltene samples.Swelling ratioProportion of solvent (%)KL-C16H34 (mg)LG-C16H34 (mg)SC-C16H34 (mg)KL -C13H20 (mg)LG-C13H20 (mg)SC-C13H20 (mg)SolidLiquidSolidLiquidSolidLiquidSolidLiquidSolidLiquidSolidLiquid1.1110535.8853.45.93--61.26.855.96.2160.66.731.25207017.5441152.313.164.316.160.615.25313.31.433046.820.136.615.759.925.773.431.575.632.449.921.41.5435––––43.123.2––––43.123.21.674051.534.444.829.8––82.354.967.244.842.234.525070.370.347.347.3––69.969.981.281.254.254.22.22551031265972.1––––79.797.460.66.732.560––––––65.698.4––5313.32.8665––––––81.8151.8––––3.3370––––––80.8188–––– The swelling ratio, proportion of solvent and adsorption mass of three asphaltene samples. All samples of each point were left to stand for 72 h in order to ensure that the asphaltene and solvent were fully mixed. The point was considered as the effective point when there was no free-flowing solvents in the mixed samples. It was thought that the solvent was completely adsorbed by the asphaltene20,21. In contrast, the presence of free-flowing solvents indicated that the amount of the solvents exceeded the adsorption ability of the asphaltene, and these points were considered as ineffective data points. After that, these mixed samples of each effective point were prepared for the XRD analysis. X-ray diffraction analysis The XRD experiments were conducted with an XRD-6100 instrument, which was equipped with a copper (Cu) tube target operating 40 kv voltage and 30 mA current. The scanning range and speed were 10–80°and 2.0 deg/min, respectively. The chemical structures of asphaltenes after solvent swelling can be characterized by the γ and 002 peaks in the XRD spectra. The parameters of dγ and d002 are calculated using the Bragg and Scherrer equations, which can be expressed as follows: where λ is the x-ray wavelength (0.15405 nm), θγ and θ002 are the diffraction angles of γ and 002. dγ and d002 are the interlayer spacing of amorphous carbon in aliphatic carbon and the microcrystals in the chemical structures of swollen asphaltenes, respectively. Results Basic geochemical characteristics of three asphaltene samples The pyrolysis characteristics of three asphaltene samples are shown in Fig. 1 and listed in Table 2. The HI and Tmax values of samples KL, LG and SC range from 489–703 mg/gTOC and from 434–444 ℃, which represents that they are type I organic matters. Based on the relationship between Req (equivalent vitrinite reflectance) and Tmax by Jarvie et al.27, the Req values of samples KL, LG, and SC are 0.65%, 0.83%, and 0.72%, respectively. The HI (mg/gTOC) versus Tmax ( ℃) of three asphaltene samples. Table 2The Rock–Eval data of three asphaltene samples.SampleS1S2Tmax (℃)HIOITOC (%)Req (%)Type(mg/g)(mg/gTOC)KL10.82526434703474.80.65ILG2.76236444489148.30.83ISC18.42421438536278.60.72IEquivalent vitrinite reflectance (Req) = 0.018 × Tmax—7.1627. The Rock–Eval data of three asphaltene samples. Equivalent vitrinite reflectance (Req) = 0.018 × Tmax—7.1627. The chemical structural characteristics of three asphaltene samples are obtained by the solid-state 13C NMR. The aliphatic and aromatic carbon functional groups are identified with their chemical shifts of 5–95 ppm and 95–150 ppm, respectively (Fig. 2). The aliphatic carbon functional groups are further divided into six sub-groups (Table 3): aliphatic methyl (fCH3al), aromatic methyl (fCH3ar), methylene (fCH2), methine (fCH), quaternary (fC), and O-alkyl (fO), with their chemical shifts of 10–19 ppm, 19–22 ppm, 22–35 ppm, 35–40 ppm, 40–55 ppm, and 55–95 ppm, respectively. Additionally, the protonated aromatic carbon (fHa, 95 − 118 ppm), bridgehead aromatic carbon (fBa, 118 − 135 ppm), branched aromatic carbons (fa, 135 − 145 ppm), and oxy-aromatic (fOa, 145 − 155 ppm) belong to the aromatic carbon functional groups. Despite their classification as type I organic matters, there are differences in the relative percentages of aliphatic and aromatic carbons (Table 3). Sample KL exhibits the highest percentage of aliphatic carbon (73.82%), followed by samples LG and SC with the percentages of 61.52% and 54.59%, respectively. The results of chemical structures demonstrate that samples KL and SC have high ratio of long aliphatic carbon chains (Fig. 2a, c), and sample LG has high ratio of aromatic carbons (Fig. 2b). The solid-state 13C nuclear magnetic resonance spectra of KL (a), LG (b), and SC (c) asphaltene samples. Table 3Structural parameters of three asphaltene samples according to the solid-state 13C NMR.SampleAliphatic (%, 5–95 nm)Aromatic (%, 95–150 nm)f(al) (%)f(ar) (%)f(CH3al)f (CH3ar)f(CH2)f (CH)f (C)f (O)f (Ha)f (Ba)f(Ca)f(Oa)KL5.2917.8924.8115.856.673.327.0610.866.661.5973.8226.18LG11.0224.7314.558.611.591.027.7316.0710.933.7661.5238.48SC4.0313.3616.2411.586.822.5510.341415.765.3254.5945.41f(al) = f(CH3al) + f (CH3ar) + f(CH2) + f(CH) + f (C) + f (O); f(ar) = f (Ha) + f (Ba) + f (Ca) + f (Oa). Structural parameters of three asphaltene samples according to the solid-state 13C NMR. f(al) = f(CH3al) + f (CH3ar) + f(CH2) + f(CH) + f (C) + f (O); f(ar) = f (Ha) + f (Ba) + f (Ca) + f (Oa). Comparison of the maximum adsorption mass of three asphaltene samples The swelling ratio generally reflects the adsorption capacity of three asphaltene samples on the n-hexadecane and n-heptylbenzene swollen solvents (Table 1). The mass of each swollen solvent adsorbed by the asphaltenes gradually approaches a saturation state as the weight of two solvents increases. The adsorption mass of n-hexadecane of samples KL and LG reach saturation at a swelling ratio of 2.22 (Fig. 3 and Table 1). In contrast to the above two samples, sample SC reaches saturation at a swelling ratio of 1.54, indicating that its adsorption capacity on saturates is lower than that of the other two samples. In terms of n-heptylbenzene adsorption mass, samples KL, SC and LG reach saturation at swelling ratios of 3.33, 2.50 and 2.22, respectively. In comparison with the adsorption ability of three asphaltene samples on n-hexadecane, it is found that samples KL and SC are able to adsorb more n-heptylbenzene, indicating the two samples exhibit stronger adsorption capacity on aromatics than saturates. The saturation swelling ratios of three asphaltene samples. C16H34 and C13H20 represent n-hexadecane and n-heptylbenzene, respectively. Variations of asphaltene’s chemical structures during solvent swelling The XRD spectra of three swollen asphaltene samples in n-hexadecane and n-heptylbenzene solvents are shown in Figs. 4 and 5. A broad γ-peak (2θ = 19°) and 002 (2θ = 26°) reflect the characteristics of aliphatic carbon functional groups and the stacking of aromatic rings. According to Eqs. (1) and (2), the dγ and d002 variations of three asphaltene samples at different swelling ratios can be calculated. As illustrated in Fig. 6, the original dγ values of samples KL, LG and SC are 4.74, 4.61 and 4.60, respectively, and decrease as the swelling ratio increases (Fig. 6a–c and Table 4). Furthermore, the dγ value under the n-hexadecane is lower than that under the n-heptylbenzene at the same swelling ratio (Fig. 6). However, there is a sharp decrease of from the beginning to the swelling ratio of 1.11. The decline of d002 with the swelling ratio can be also discerned in samples KL and SC (Fig. 6d, f), whereas the d002 of sample LG does not appear to follow this evolution (Fig. 6e). Unlike the evolution of dγ (Fig. 6b), the d002 of sample LG increases sharply during the primary swelling stage and then decrease with the swelling ratio (Fig. 6e). The d002 values of this sample under n-hexadecane (3.50) and n-heptylbenzene (3.52) at the swelling ratio of 2.00 are very close the original value (3.51). The X-ray diffraction spectra of solvent-swollen asphaltene with n-heptylbenzene (C13H20) of three asphaltene samples. The X-ray diffraction spectra of solvent-swollen asphaltene with n-hexadecane (C16H34) of three asphaltene samples. (a) KL, (b) LG, and (c) SC. The dy and d002 versus swelling ratio of KL (a, d), LG (b, e) and SC (c, f) asphaltene samples in the n-hexadecane (C16H34) and n-heptylbenzene (C13H20) solvents. Table 4Changs of dγ and d002 of three asphaltene samples during n-hexadecane (C16H34) and n-heptylbenzene (C13H20) swelling processes.Swelling ratioProportion of solvent (%)KL-C16H34LG-C16H34SC-C16H34KL -C13H20LG-C13H20SC-C13H20dγd002dγd002dγd002dγd002dγd002dγd0021.00*04.743.554.613.514.63.594.743.554.613.514.63.591.11104.73.564.393.594.53.564.593.554.453.481.25204.623.554.333.54.443.524.733.534.443.584.563.511.43304.573.544.413.54.413.54.623.524.483.544.543.51.54354.413.461.67404.463.484.393.464.573.454.443.544.433.522504.473.494.413.54.533.464.343.524.483.472.22552.5604.563.582.86653.33704.523.45The dγ and d002 values at the swelling ratio of 1.00 represent the original values with no solvent swelling. Changs of dγ and d002 of three asphaltene samples during n-hexadecane (C16H34) and n-heptylbenzene (C13H20) swelling processes. The dγ and d002 values at the swelling ratio of 1.00 represent the original values with no solvent swelling. Discussion Factors influencing the maximum adsorption mass of saturates and aromatics on the asphaltene The factors influencing the maximum adsorption mass on the asphaltene mainly depend on the characteristics of swollen solvents and chemical structures of the asphaltene. The saturates mainly consist of C–C and C–H bonds with symmetrical electron cloud distributions and weak polarity. Their interactions with organic macromolecules are mainly Van der Walaas force. In comparison with the saturates, the aromatics consist of a series of benzene rings that can adsorb on organic macromolecules with π-π interaction28. Therefore, the maximum adsorption mass of aromatics exceeds that of saturates in samples KL and SC. Liang et al.21 proposed that high aliphatic carbon content of solid bitumen is responsible for the significant differences in the swelling ratios between n-hexadecane and n-heptylbenzene solvents. It is found that sample KL exhibits the largest differences in the saturation swelling ratios between the two swollen solvents (Fig. 3), which is also associated to its highest f(al) and HI in three samples (Fig. 1 and Table 3). The f(ar) is a measure of the aromatic carbon content of organic macromolecules and is commonly employed to describe the adsorption ability of aromatics. Despite the f(ar) of this sample being the highest among the three samples, the saturation swelling ratio in n-heptylbenzene solvent is the greatest. This phenomenon is attributed to its low thermal maturity, high HI, and molecular weight. In comparison with sample LG, the higher HI, lower thermal maturity, and higher f(ar) resulted in the higher maximum adsorption mass of aromatics for sample SC (Fig. 3, Tables 1, 3). With regard to the sample LG, the saturation masss of aromatics and saturates for sample LG are same (Fig. 3). This phenomenon has been also observed in a previous study20. We think that the higher thermal maturity and lower HI together with appropriate f(ar) caused the decline of the maximum adsorption mass of aromatics, approaching the adsorption mass of saturates. Molecular model of asphaltene during the solvent swelling According to the results of solid-state 13C NMR analysis, swelling experiments, and XRD analysis, molecular models of chemical structure variations in asphaltenes with long and short aliphatic chains during solvent swelling have been established (Fig. 7). Prior to the solvent swelling, the amorphous carbons in the asphaltene are densely packed. For asphaltenes with long aliphatic chains, most of the saturates and aromatics accumulate between the aliphatic carbon chains, resulting an obvious decline in dγ as the swelling ratio increases (Fig. 6a, c). Additionally, the d002 value also decreases as the swelling ratio increases, indicating some aromatics accumulate between the aromatic carbon chains (Fig. 7). Schematic diagrams of the swelling models of asphaltenes with long or short aliphatic chains. Liang et al.20 found that the dγ and d002 values decreased with the swelling ratio for the solid bitumen, kerogen, and coal, while they did not give the further explanation. We think that the solvent provides kinetic energy and forces disordered asphaltene macromolecules to a more ordered and stable stage through rearrangement, folding, and compression29,30, thereby the structural contraction leads to a decline of the dγ and d002 values. Unlike samples KL and SC, sample LG shows abnormal initial increase in its d002 value during the solvent swelling (Fig. 6e). We think its highest thermal maturity, lower HI and f(al) are the main reasons of the same maximum adsorption mass of saturates and aromatics (Fig. 3), leading to irregular variations in the d002 value in the initial swelling stage (Fig. 6e). Besides, the abnormal initial increase in d002 is found in sample LG during the solvent swelling (Fig. 6e). Its highest thermal maturity (Req = 0.83%), lower HI, and higher f(ar) lead to more ordered stacking of aromatic sheets and a denser structure. This causes a temporary increase in d002, while the overall adsorption sites are limited due to reduced aliphatic chains. The asphaltene with short aliphatic carbon chains shows different characteristic of structural changes during the solvent swelling, and the saturates and aromatics mainly accumulate between the aliphatic carbon chains (Fig. 7). By comparison, the aromatics accumulate between aromatic carbon chains in short aliphatic chain asphaltene more difficultly than in long aliphatic chain asphaltene (Fig. 7), which causes a lower adsorption mass of aromatics (Fig. 3). Our results show that the asphaltene has strong adsorption capacity on liquid hydrocarbons, and the interactions between the asphaltene and liquid hydrocarbons should be studied in the future. The differences of swelling characteristics of asphaltene, kerogen and solid bitumen The asphaltene, kerogen, and solid bitumen are common organic macromolecules in the crude oil, reservoir, and source rocks. Our study integrates the swelling data of kerogen19,20, solid bitumen24, and our asphaltene samples to reveal the evolution pattern of the saturation swelling ratio of saturates with f(al) and the saturation swelling ratio of aromatics with f(ar) (Fig. 8). The long aliphatic chains can easily escape from high-molecule organic matters as thermal maturity increases, which results in the decline of HI f(al) of organic macromolecules. The saturation swelling ratio of saturates for kerogen, solid bitumen and asphaltene decreases with the decline of the f(al) with R2 of 0.80 (Fig. 8a). According to the principle of “compatibility with similar components”, the higher f(al) value of organic macromolecules is indicative of their ability to adsorb more saturates. Consequently, a better fitting relationship shows that the saturation swelling ratio of saturates is principally determined by the f(al). The aliphaticity (%) versus saturation swelling ratio under n-hexadecane solvent (a) and the aromaticity (%)versus saturation swelling ratio under n-heptylbenzene solvent (b) for different organic matters. Notes: the blue dash line represents the possible evolution trend of asphaltene. With the increasing of thermal maturity, the aliphatic chains escape from the organic matters, causing the increase in f(al). The maximum adsorption mass of aromatics is higher than that of saturates under the same conditions (Fig. 8). Compared to the saturation swelling ratio of saturates, it is worth noting that the saturation swelling ratio of aromatics with the f(ar) shows different evolution trends (Fig. 8b). Under the similar f(ar), the saturation swelling ratio of aromatics for solid bitumen is obviously higher than that for asphaltene and kerogen. Although factors influencing adsorption ability of aromatics are more complex than that of saturates, the differences are also influenced by different chemical structures of different organic matters. The solid bitumen and asphaltene are the products of kerogen or crude oil cracking. During the early thermal maturation stage, the C–C bonds in long aliphatic chains connected with benzene can be easily cracked with the increasing of thermal maturity due to its low activation energies31,32. By comparison, the length of aliphatic chains of kerogen is higher than its cracking products. The solid bitumen and asphaltene mainly consist of lower aliphatic chains than kerogen under the similar f(ar), which cause that they can adsorb more aromatics. With further increasing of thermal maturity and f(ar), the three types of organic macromolecules evolve more stable structures. Consequently, the saturation swelling ratio of aromatics for them gradually becomes smaller at higher thermal maturity and f(ar) (Fig. 8b). Implications for the hydrocarbon expulsion process of the shale The expulsion of generated oil from the shale is governed by the retention capacity16,33. When the generated oil reaches the shale’s retention mass, it can expel from the shale2. The resource potential of shale oil primarily depends on the content of the retained oil in the shale, so the expulsion process serves as a critical link connecting hydrocarbon generation, migration, and accumulation. Previous swelling experiments mainly focused on the influences of adsorption ability of kerogen14,16,17,25,33, and neglected the influences of asphaltene. The adsorption ability of saturates for asphaltene is related to its f(al) (Fig. 8a), so the maximum mass of saturates (Msa) adsorbed by the given masses of kerogen (Mk) and asphaltene (Ma) at the same thermal maturity can be expressed by: where Msa is the maximum mass of saturates adsorbed by asphaltene and kerogen, mg/g. Sk(sa) is the maximum mass of saturates adsorbed by kerogen, mg/g. Ma and Mk are the masses of asphaltene and kerogen at the same thermal maturity, mg. f is the ratio of the masses of asphaltene and kerogen. The adsorption ability of aromatics for asphaltene is greater than that for kerogen at the same f(ar) (Fig. 8b), so the maximum mass of aromatics (Mar) adsorbed by the given masses of kerogen (Mk) and asphaltene (Ma) at the same thermal maturity can be expressed by: where Mar is the maximum mass of aromatics adsorbed by asphaltene and kerogen, mg/g. Sa(ar) and Sk(ar) are the masses of aromatics adsorbed by asphaltene and kerogen, mg/g. S is the ratio of the maximum mass of aromatics adsorbed by asphaltene and kerogen at the same thermal maturity. For example, Liang et al.34 calculated values of f(al) and f(ar) of the Lucaogou kerogen under different EasyRo%. On this basis, f is calculated by evolution lines of asphaltene and kerogen in Fig. 8b. Thereby, the determination of f under different thermal maturities can be referenced by Table 5 and Fig. 9. Table 5The aromaticity, aliphaticity and the ratio of the maximum masses of aromatics adsorbed by asphaltene and kerogen from the Lucaogou shale under different thermal maturities.EasyRo (%)f(ar)f(al)Sa/Sk(%)0.5639611.270.741591.260.7549511.230.8457431.201.08021.101.0587131.061.169281.031.279551.011.549641.011.829731.00f(ar) and f(al) represent the aromaticity and aliphaticity, Sa/Sk is the ratio of the maximum mass of aromatics adsorbed by asphaltene and kerogen. The data of f(ar) and f(al) under different thermal maturities are from34, and the corresponding Sa/Sk is calculated based on Fig. 8b. The aromaticity, aliphaticity and the ratio of the maximum masses of aromatics adsorbed by asphaltene and kerogen from the Lucaogou shale under different thermal maturities. f(ar) and f(al) represent the aromaticity and aliphaticity, Sa/Sk is the ratio of the maximum mass of aromatics adsorbed by asphaltene and kerogen. The data of f(ar) and f(al) under different thermal maturities are from34, and the corresponding Sa/Sk is calculated based on Fig. 8b. The ratio of the maximum mass of aromatics adsorbed by asphaltene and kerogen (Sa(ar)/ Sk(ar)) of the Lucaogou shale under different thermal maturities (EasyRo%). According to the results of gold tube pyrolysis experiments of the Lucaogou kerogen33,35, the ratio of masses of asphaltene versus kerogen (Ma/Mk) firstly increases and then decreases with EasyRo%, and shows obvious variation in the EasyRo% range of 0.7 − 1.3%, and the mass of asphaltene is even equal to the kerogen at EasyRo% = 0.87% (Fig. 10). The asphaltene is the main fraction of kerogen cracking during the oil generation stage, consequently, its adsorption capacity for saturates and aromatics should be considered in the future studies about hydrocarbon expulsion of the shale. The ratio of the masses of asphaltene and kerogen (Ma/Mk) of the Lucaogou shale under different thermal maturities (EasyRo%). The data are from refs 33 and 35. Conclusions In this research, we took three asphaltene samples as the research target, designed swelling experiments, and conducted the 13C nuclear magnetic resonance (NMR) and X-ray diffraction (XRD) analysis. The following conclusions can be drawn: The saturates mainly consist of C–C and C–H bonds with symmetrical electron cloud distributions and weak polarity. Their interaction with organic macromolecules is mainly Van der Walaas force. The asphaltene has abundant benzene rings that can adsorb on organic macromolecules with π-π interaction. Most of the saturates and aromatics accumulate between the aliphatic carbon chains in the asphaltenes with long and short aliphatic chains. whereas it is difficult for the aromatics to accumulate between aromatic carbon chains in short aliphatic chain asphaltenes. The saturates mainly consist of C–C and C–H bonds with symmetrical electron cloud distributions and weak polarity. Their interaction with organic macromolecules is mainly Van der Walaas force. The asphaltene has abundant benzene rings that can adsorb on organic macromolecules with π-π interaction. Most of the saturates and aromatics accumulate between the aliphatic carbon chains in the asphaltenes with long and short aliphatic chains. whereas it is difficult for the aromatics to accumulate between aromatic carbon chains in short aliphatic chain asphaltenes. The aliphaticity-f(al) of kerogen, solid bitumen and asphaltene primarily governs their adsorption capacity of saturates, while their adsorption capacity for aromatics is influenced by the complex interplay of aliphaticity, aromaticity-f(ar), and thermal maturity. Three types of organic macromolecules evolve more stable structures at higher thermal maturity, so that the saturation swelling ratio of aromatics for them gradually become smaller and tend to be the same. The aliphaticity-f(al) of kerogen, solid bitumen and asphaltene primarily governs their adsorption capacity of saturates, while their adsorption capacity for aromatics is influenced by the complex interplay of aliphaticity, aromaticity-f(ar), and thermal maturity. Three types of organic macromolecules evolve more stable structures at higher thermal maturity, so that the saturation swelling ratio of aromatics for them gradually become smaller and tend to be the same. Two new methods are established to calculated the masses of saturates and aromatics adsorbed by asphaltene and kerogen, providing a new tool for the assessment of liquid hydrocarbon retention in shale. The asphaltene is the main fraction of kerogen cracking during the early thermal maturation stage, so its capacity for liquid hydrocarbons adsorption should be also considered in the future studies of hydrocarbon expulsion from shale. Two new methods are established to calculated the masses of saturates and aromatics adsorbed by asphaltene and kerogen, providing a new tool for the assessment of liquid hydrocarbon retention in shale. The asphaltene is the main fraction of kerogen cracking during the early thermal maturation stage, so its capacity for liquid hydrocarbons adsorption should be also considered in the future studies of hydrocarbon expulsion from shale. Author contributions Shi Shuyong and Liang Tian wrote the mainuscript, Lin Xianhui and Shi Shuyong prepared the figures and tables, all authors reviewed the manuscript. Funding This work was financially supported by the National Natural Science Foundation of China (No. 42273053, 42402136), Basic and Applied Basic Research Foundation of Guangdong Province (2023A1515011646), Director’s Fund of Guangzhou Institute of Geochemistry, CAS (2022SZJ5T-06). This is contribution No.IS-3729 from GIGCAS. Data availability Data is provided within the manuscript or supplementary information files. Declarations Competing interests The authors declare no competing interests. Footnotes Publisher’s note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations. References Associated Data Data Availability Statement Data is provided within the manuscript or supplementary information files.