Protocol for mapping RNA G-quadruplex for chromatin-bound RNA using d-rG4-seq Authors: Yong Woo Lee, Vered Levy, Jeannie T Lee Published: 2024 ABSTRACT SummaryHere, we present a protocol for using d-rG4-seq, a technique for mapping RNA G-quadruplex (rG4) for chromatin-bound RNA. We describe steps for identifying in vivo rG4 structures based on differential sensitivity of rG4 to dimethyl sulfate (DMS) modification, folding in the presence of monovalent cations, K+ versus Li+, and reverse transcriptase (RT) readthrough when folded. We then detail procedures for isolating RNA from the chromatin-bound fractions to enrich for epigenetic regulators and comparing in vitro versus in vivo profiles.For complete details on the use and execution of this protocol, please refer to Lee et al.1Subject areas: Genomics, Molecular Biology, Gene Expression Before you begin This protocol describes a method for identifying RNA G-quadruplex (rG4) structures inside cells, as originally described for our analysis of Xist RNA.1 The method incorporates previously established protocols to identify RNA duplexes2 and RNA G-quadruplexes.3,4,5,6 We purify chromatin-associated RNAs from ES cells to enrich for epigenetic regulators (Figure 1A). For in vitro analysis, we do not include a DMS treatment step (-DMS, Figure 1A). We fragment the RNA, ligate adaptors, and denature the RNA to eliminate secondary structures. We then renature the RNA in the presence of either monovalent cation K+ (which enables rG4 to form stably) or Li+ (which does not stabilize rG4). We next reverse-transcribe the RNA using Superscript III RT, perform size-selection, and clone the products for sequencing. In principle, rG4s that reform in vitro following denaturation would occur only in K+, but not Li+. Because RT cannot process past a folded rG4, we can infer the formation of rG4 structures by observing a chain-termination event (“RT-Stop”) following sequencing.3 For in vivo analysis, we modify the pipeline by first treating cells with DMS in vivo to capture native RNA conformation (+DMS, Figure 1A). We then denature and renature the RNA in the presence of K+ versus Li+ prior to RT-primer extension analysis — performed as for in vitro analysis. The d-rG4-seq pipeline (A) d-rG4-seq procedure summary. In vitro analysis does not utilize the DMS treatment step (-DMS). The in vivo analysis begins with DMS treatment to capture in-cell RNA conformations (+DMS). All other steps are the same for in vitro and in vivo analyses. Chromatin-bound fraction is isolated to enrich the non-coding RNAs involved in the epigenetic regulations. RNAs are further selected with PolyA+ selection and heat fragmented. Size selection is performed to obtain RNA methylation-dependent RT-stop products. Adaptor-ligated RNA is initially size-selected by gel elution, targeting lengths between 85 and 105 nucleotides. During reverse transcription, RT-stops occur in the rG4 folding regions and DMS-modified adenine and cytosine nucleotides. RT-stop products are isolated by size selection of cDNA fragments shorter than full-length products (75–105 nt). Additional RT-stop product enrichment is performed by excising the PCR products in the 78–105 nt length range. (B) RNA and cDNA fragments in the indicated length are selected in 8% denaturing and native gels. SYBR gold staining is used to visualize the nucleic acids. DMS-treated (DMS+) and non-treated (DMS-) RNA samples are reverse transcribed with K+ and Li+ containing buffers. DMS can methylate 3 of 4 nucleosides in RNA: Adenosine (A) at the N1 position, cytosine (C) at the N3 position, and guanine at the N7 position. When RNA is in rG4 conformation, N7-G is protected from DMS because of its involvement in G:G hydrogen bonding within the tetrad, whereas N1-A and N3-C are not protected because they are not involved in Hoogsteen base-pairing. Thus, following a round of denaturation and renaturation, if the G-rich region did not fold into rG4 after denaturation, we infer that the N7-G was DMS-methylated in cells and therefore did not adopt an rG4 conformation in vivo. If a G-rich region could fold into rG4 following denaturation, the N7-G must have been protected from DMS in vivo and we could therefore infer the occurrence of an rG4 in vivo. In this case, the rG4 would refold following denaturation in the presence of K+ and create RT-stops. Therefore, the presence of DMS-resistant K+-dependent RT-stops peaks within a G-tract indicates a folded rG4 in cells. In this way, in vitro and in vivo rG4 profiles can be surveyed through differential RNA sensitivities to DMS within G-tracts and differential renaturation under K+ versus Li+ conditions. To increase detection sensitivity of this procedure, we enrich RT-stop products using a size-based isolation approach2,3 (Figure 1B). The enriched RT-stop cDNA libraries are then deeply sequenced using the Illumina platform. We use rG4Seeker and StructureFold software to analyze RNA structure from in vivo DMS modification profiles. This protocol focuses on the d-rG4-seq method and provides guidance on the initial in silico analysis. CRITICAL: DMS is a highly toxic compound that is volatile to the air. To minimize exposure, DMS treatments are done in a chemical fume hood. Consult with the institute safety manager before starting. Adaptor and primer-extension oligos preparation Timing: 2–3 h 1.Adaptor 5′ Adenylation.a.Phosphorylate the adaptor 5′ end.i.Incubate 3 μL of 100 μM adaptor stock, 5 μL of T4 DNA ligase buffer, 1 μL of T4 polynucleotide kinase, and 41 μL of deionized water for 1 h at 37°C.ii.Purify the adaptor using an Oligo Clean & Concentrator.b.Adenylate the phosphorylated adaptor,i.Using the 5′ DNA oligo adenylation kit, combine 5 μL of 10 × 5′ adenylation buffer, 5 μL of 1 mM ATP, 5 μL of Mth RNA ligase, and the phosphorylated adaptor in a 50 μL reaction.ii.Incubate for 1 h at 65°C.iii.Recover the adaptor using an oligo clean-up kit. Adaptor 5′ Adenylation.a.Phosphorylate the adaptor 5′ end.i.Incubate 3 μL of 100 μM adaptor stock, 5 μL of T4 DNA ligase buffer, 1 μL of T4 polynucleotide kinase, and 41 μL of deionized water for 1 h at 37°C.ii.Purify the adaptor using an Oligo Clean & Concentrator.b.Adenylate the phosphorylated adaptor,i.Using the 5′ DNA oligo adenylation kit, combine 5 μL of 10 × 5′ adenylation buffer, 5 μL of 1 mM ATP, 5 μL of Mth RNA ligase, and the phosphorylated adaptor in a 50 μL reaction.ii.Incubate for 1 h at 65°C.iii.Recover the adaptor using an oligo clean-up kit. a.Phosphorylate the adaptor 5′ end.i.Incubate 3 μL of 100 μM adaptor stock, 5 μL of T4 DNA ligase buffer, 1 μL of T4 polynucleotide kinase, and 41 μL of deionized water for 1 h at 37°C.ii.Purify the adaptor using an Oligo Clean & Concentrator. Phosphorylate the adaptor 5′ end.i.Incubate 3 μL of 100 μM adaptor stock, 5 μL of T4 DNA ligase buffer, 1 μL of T4 polynucleotide kinase, and 41 μL of deionized water for 1 h at 37°C.ii.Purify the adaptor using an Oligo Clean & Concentrator. i.Incubate 3 μL of 100 μM adaptor stock, 5 μL of T4 DNA ligase buffer, 1 μL of T4 polynucleotide kinase, and 41 μL of deionized water for 1 h at 37°C. Incubate 3 μL of 100 μM adaptor stock, 5 μL of T4 DNA ligase buffer, 1 μL of T4 polynucleotide kinase, and 41 μL of deionized water for 1 h at 37°C. ii.Purify the adaptor using an Oligo Clean & Concentrator. Purify the adaptor using an Oligo Clean & Concentrator. b.Adenylate the phosphorylated adaptor,i.Using the 5′ DNA oligo adenylation kit, combine 5 μL of 10 × 5′ adenylation buffer, 5 μL of 1 mM ATP, 5 μL of Mth RNA ligase, and the phosphorylated adaptor in a 50 μL reaction.ii.Incubate for 1 h at 65°C.iii.Recover the adaptor using an oligo clean-up kit. Adenylate the phosphorylated adaptor,i.Using the 5′ DNA oligo adenylation kit, combine 5 μL of 10 × 5′ adenylation buffer, 5 μL of 1 mM ATP, 5 μL of Mth RNA ligase, and the phosphorylated adaptor in a 50 μL reaction.ii.Incubate for 1 h at 65°C.iii.Recover the adaptor using an oligo clean-up kit. i.Using the 5′ DNA oligo adenylation kit, combine 5 μL of 10 × 5′ adenylation buffer, 5 μL of 1 mM ATP, 5 μL of Mth RNA ligase, and the phosphorylated adaptor in a 50 μL reaction. Using the 5′ DNA oligo adenylation kit, combine 5 μL of 10 × 5′ adenylation buffer, 5 μL of 1 mM ATP, 5 μL of Mth RNA ligase, and the phosphorylated adaptor in a 50 μL reaction. ii.Incubate for 1 h at 65°C. Incubate for 1 h at 65°C. iii.Recover the adaptor using an oligo clean-up kit. Recover the adaptor using an oligo clean-up kit. Note: Commercially available 5′ adenylated adaptors can replace this step. 2.Primer-extension oligo 5′ phosphorylation,a.Denaturing-PAGE purification of the 56 nt primer extension oligo.i.Resuspend 300 pmol of iSp18 PE Reverse oligo in 10 μl of 1x UREA gel loading buffer.ii.Denature the oligo for 3 min at 80°C.iii.Run the mixture in an 8% acrylamide-urea denaturing gel.iv.Recover the oligos from the excised band using the ZR small-RNA PAGE Recovery Kit.Note: This step reduces the background noise originating from incomplete oligo byproducts.b.Primer-extension oligo phosphorylation:i.Mix 3 μL of 100 μM PAGE-purified iSp18 PE Reverse oligo, 5 μL of T4 DNA ligase buffer, 1 μL of T4 polynucleotide kinase, and 41 μL of deionized water.ii.Incubate the reaction mixture for 1 h at 37°C.iii.Purify the oligo using the ZR small-RNA PAGE Recovery Kit. Primer-extension oligo 5′ phosphorylation,a.Denaturing-PAGE purification of the 56 nt primer extension oligo.i.Resuspend 300 pmol of iSp18 PE Reverse oligo in 10 μl of 1x UREA gel loading buffer.ii.Denature the oligo for 3 min at 80°C.iii.Run the mixture in an 8% acrylamide-urea denaturing gel.iv.Recover the oligos from the excised band using the ZR small-RNA PAGE Recovery Kit.Note: This step reduces the background noise originating from incomplete oligo byproducts.b.Primer-extension oligo phosphorylation:i.Mix 3 μL of 100 μM PAGE-purified iSp18 PE Reverse oligo, 5 μL of T4 DNA ligase buffer, 1 μL of T4 polynucleotide kinase, and 41 μL of deionized water.ii.Incubate the reaction mixture for 1 h at 37°C.iii.Purify the oligo using the ZR small-RNA PAGE Recovery Kit. a.Denaturing-PAGE purification of the 56 nt primer extension oligo.i.Resuspend 300 pmol of iSp18 PE Reverse oligo in 10 μl of 1x UREA gel loading buffer.ii.Denature the oligo for 3 min at 80°C.iii.Run the mixture in an 8% acrylamide-urea denaturing gel.iv.Recover the oligos from the excised band using the ZR small-RNA PAGE Recovery Kit.Note: This step reduces the background noise originating from incomplete oligo byproducts. Denaturing-PAGE purification of the 56 nt primer extension oligo.i.Resuspend 300 pmol of iSp18 PE Reverse oligo in 10 μl of 1x UREA gel loading buffer.ii.Denature the oligo for 3 min at 80°C.iii.Run the mixture in an 8% acrylamide-urea denaturing gel.iv.Recover the oligos from the excised band using the ZR small-RNA PAGE Recovery Kit.Note: This step reduces the background noise originating from incomplete oligo byproducts. i.Resuspend 300 pmol of iSp18 PE Reverse oligo in 10 μl of 1x UREA gel loading buffer. Resuspend 300 pmol of iSp18 PE Reverse oligo in 10 μl of 1x UREA gel loading buffer. ii.Denature the oligo for 3 min at 80°C. Denature the oligo for 3 min at 80°C. iii.Run the mixture in an 8% acrylamide-urea denaturing gel. Run the mixture in an 8% acrylamide-urea denaturing gel. iv.Recover the oligos from the excised band using the ZR small-RNA PAGE Recovery Kit.Note: This step reduces the background noise originating from incomplete oligo byproducts. Recover the oligos from the excised band using the ZR small-RNA PAGE Recovery Kit.Note: This step reduces the background noise originating from incomplete oligo byproducts. Note: This step reduces the background noise originating from incomplete oligo byproducts. b.Primer-extension oligo phosphorylation:i.Mix 3 μL of 100 μM PAGE-purified iSp18 PE Reverse oligo, 5 μL of T4 DNA ligase buffer, 1 μL of T4 polynucleotide kinase, and 41 μL of deionized water.ii.Incubate the reaction mixture for 1 h at 37°C.iii.Purify the oligo using the ZR small-RNA PAGE Recovery Kit. Primer-extension oligo phosphorylation:i.Mix 3 μL of 100 μM PAGE-purified iSp18 PE Reverse oligo, 5 μL of T4 DNA ligase buffer, 1 μL of T4 polynucleotide kinase, and 41 μL of deionized water.ii.Incubate the reaction mixture for 1 h at 37°C.iii.Purify the oligo using the ZR small-RNA PAGE Recovery Kit. i.Mix 3 μL of 100 μM PAGE-purified iSp18 PE Reverse oligo, 5 μL of T4 DNA ligase buffer, 1 μL of T4 polynucleotide kinase, and 41 μL of deionized water. Mix 3 μL of 100 μM PAGE-purified iSp18 PE Reverse oligo, 5 μL of T4 DNA ligase buffer, 1 μL of T4 polynucleotide kinase, and 41 μL of deionized water. ii.Incubate the reaction mixture for 1 h at 37°C. Incubate the reaction mixture for 1 h at 37°C. iii.Purify the oligo using the ZR small-RNA PAGE Recovery Kit. Purify the oligo using the ZR small-RNA PAGE Recovery Kit. Key resources table REAGENT or RESOURCESOURCEIDENTIFIERChemicals, peptides, and recombinant proteinsT4 polynucleotide kinaseNew England BiolabsCat# M0201T4 DNA ligase reaction bufferNew England BiolabsCat#B0202STRIzol reagentThermo ScientificCat# 15596018SYBR Gold nucleic acid gel stainInvitrogenCat#S11494T4 RNA ligase 2, truncated KQNew England BiolabsCat# M0373SUPERase·In RNase inhibitorInvitrogenCat#AM2694SuperScript III reverse transcriptaseInvitrogenCat#18080085CircLigase ssDNA ligaseEpicentreCat# CL4111KTURBO DNaseInvitrogenCat#AM2238Ribonucleoside vanadyl complexNew England BiolabsCat# S1402S3X Flag peptideSigmaCat# F4799Dimethyl sulfateSigmaCat# 320293Critical commercial assays5′ DNA Adenylation KitNew England BiolabsCat#E2610SOligotex Direct mRNA kitQIAGENCat# 70022Oligo Clean & ConcentratorZymoCat#D4060ZR small-RNA PAGE Recovery KitZymoCat#R1070NEBNext Poly(A) mRNA Magnetic Isolation ModuleNew England BiolabsCat#E7490SAgencourt AMPure XP BeadsBeckman CoulterCat#A63881NEBNext Multiplex Oligos for Illumina (Index Primers Set 1)New England BiolabsCat#E7335SNEBNext Multiplex Oligos for Illumina (Index Primers Set 2)New England BiolabsCat#E7500SSoftware and algorithmsSAMtools v1.4.1Li et al.7http://samtools.sourceforge.net/STAR aligner (v2.7.3)Dobin et al.8https://github.com/alexdobin/STARCutadapt v1.8.1Marcel9https://cutadapt.readthedocs.io/en/stable/#Bowtie2Langmead and Salzberg10http://bowtie-bio.sourceforge.net/bowtie2/index.shtmlBowtie v1.1.1Langmead et al.11http://bowtie-bio.sourceforge.net/index.shtmlPython/Biopython v1.70Cock et al.12https://biopython.org/Prinseq-lite v0.20.4Schmieder and Edwards13https://sourceforge.net/projects/prinseq/files/Cufflinks v2.2.1Trapnell et al.14http://cole-trapnell-lab.github.io/cufflinks/ExcelMicrosoftwww.office.comStructurefold2Tack et al.15https://github.com/StructureFold2/StructureFold2rG4-seekerChow et al.16https://github.com/TF-Chan-Lab/rG4-seekerOligonucleotides3 DNA adapterAGA TCG GAA GAG CAC ACG TCT GAA C/3ddC/N/AiSp18 PE reverseNNN NNN AGA TCG GAA GAG CGT CGT GTA GGG AAA GA/iSp18/G TTC AGA CGT GTG CTC TTC CGN/ART-stop amp forwardGTT CAG ACG TGT GCT CTT CCG ATC TN/ART-stop amp reverseTCT TTC CCT ACA CGA CGC TCT TCC GN/A Materials and equipment Ribonucleoside Vanadyl Complex (RVC) stock solutionReagentFinal concentrationAmountTris pH 7.5 (200 mM)200 mM0.5 mL Ribonucleoside Vanadyl Complex (RVC) stock solution Note: Incubate the sealed vial for 10 min at 65°C. Make 0.5 mL Aliquots and store at −20°C until use. Once thawed, avoid refreezing the aliquot. NIB-1 bufferReagentFinal concentrationAmountTris pH 7.5 (1 M)15 mM0.75 mLNaCl (5 M)15 mM0.15 mLMgCl2 (1 M)5 mM0.25 mLCaCl2 (1 M)1 mM0.05 mLKCl (2 M)60 mM1.5 mLSucrose (1 M)250 mM12.5 mLNonidet-P-40 (100%)0.30%0.15 mL2-Mercaptoethanol (100%)0.10%0.05 mLddH2ON/A34.6 mLTotalN/A50 mLStore at 4°C for up to 1 month. NIB-1 buffer Store at 4°C for up to 1 month. NIB-2 bufferReagentFinal concentrationAmountTris pH 7.5 (1 M)15 mM0.75 mLNaCl (5 M)15 mM0.15 mLMgCl2 (1 M)5 mM0.25 mLCaCl2 (1 M)1 mM0.05 mLKCl (2 M)60 mM1.5 mLSucrose (1 M)250 mM12.5 mLddH2ON/A34.8 mLTotalN/A50 mLStore at 4°C for up to 1 month. NIB-2 buffer Store at 4°C for up to 1 month. NUN1 bufferReagentFinal concentrationAmountTris pH 8.0 (2 M)20 mM0.5 mLNaCl (5 M)75 mM0.75 mLEDTA (0.5 M)0.5 mM0.05 mLGlycerol (100%)50%25 mLddH2ON/A23.7 mLTotalN/A50 mLStore at −20°C for up to 12 months. NUN1 buffer Store at −20°C for up to 12 months. NUN2 bufferReagentFinal concentrationAmountHEPES pH 7.6 (1 M)20 mM1 mLMgCl2 (1 M)75 mM3.75 mLEDTA (0.5 M)0.2 mM0.02 mLNaCl (5 M)300 mM3 mLUrea (10 M)1 M5 mLNonidet-P-40 (100%)1%0.5 mLddH2ON/A36.73 mLTotalN/A50 mLStore at 4°C for up to 12 months. NUN2 buffer Store at 4°C for up to 12 months. 10x RNA fragmentation bufferReagentFinal concentrationAmountTris pH 8.0 (2 M)1 M1 mLMgCl2 (1 M)20 mM0.04 mLddH2ON/A0.96 mLTotalN/A2 mLStore at −20°C. 10x RNA fragmentation buffer Store at −20°C. 8% Acrylamide/Urea Denaturing gel mixReagentFinal concentrationAmountAcrylamide solution (29:1) 40%8%10 mLTBE (10x)1x5 mLUrea8 M24 gddH2ON/Ato 50 mLTotalN/A50 mLStore at 4°C for up to 3 months. 8% Acrylamide/Urea Denaturing gel mix Store at 4°C for up to 3 months. 8% Acrylamide/TBE Native gel mixReagentFinal concentrationAmountAcrylamide solution (29:1) 40%8%10 mLTBE (10x)1x5 mLddH2ON/A35 mLTotalN/A50 mLStore at 4°C for up to 3 months. 8% Acrylamide/TBE Native gel mix Store at 4°C for up to 3 months. 2x Urea gel loading bufferReagentFinal concentrationAmountUREA8 M4.8 gTBE (10x)1x1 mLBromophenol blue (1%)0.01%0.1 mLXylene Cyanol FF (1%)0.03%0.3 mLddH2ON/Ato 10 mLTotalN/A10 mLStore at −20°C. 2x Urea gel loading buffer Store at −20°C. 5x K + RT bufferReagentFinal concentrationAmountTris pH 7.5 (1 M)100 mM0.5 mLKCl (2 M)750 mM1.875 mLMgCl2 (1 M)15 mM0.075 mLddH2ON/A2.55 mLTotalN/A5 mLStore at −20°C. 5x K + RT buffer Store at −20°C. 5x Li+ RT bufferReagentFinal concentrationAmountTris pH 7.5 (1 M)100 mM0.5 mLLiCl (2 M)750 mM1.875 mLMgCl2 (1 M)15 mM0.075 mLddH2ON/A2.55 mLTotalN/A5 mLStore at −20°C. 5x Li+ RT buffer Store at −20°C. Step-by-step method details DMS treatment to cultured cells Timing: 2–3 h DMS treatment converts RNA structural features to the forms of RNA base methylations. The covalently attached RNA methylation patterns persist during RNA purification and fragmentation under denaturing conditions (Figure 1A). 1.Grow 8 × 107 mouse embryonic stem cells (mES) per experimental condition. Grow 8 × 107 mouse embryonic stem cells (mES) per experimental condition. CRITICAL: The last media replacement must be at least 6 h before the DMS treatment to prevent the stress response that may impact RNA structures. Samples should be processed immediately by swift cell harvesting, flash freeze, and using pre-chilled buffers. Note: Pre-chill the PBS/25% 2-Mercaptoethanol solution. Place the needle, syringe, ethanol, and 2-Mercaptoethanol in the chemical hood. 2.Harvest the cells.a.Wash cells once with 8 mL PBS buffer.b.Apply 6 mL of 0.05% trypsin per 15 cm plate.c.Incubate dishes in a 37°C incubator for 5 min and neutralize trypsin with 5 mL of cell culture media.d.Transfer cells from each plate to 15 mL Falcon tubes and collect the cells by centrifugation at 300 g for 3 min.e.Aspirate the supernatant.f.Use 5 mL cell culture media to resuspend pellets in 2 tubes for DMS treatment.g.Snap freeze the cell pellets in the other 2 tubes for the non-DMS treated controls.h.Quickly transfer samples for DMS treatment to the chemical hood. Harvest the cells.a.Wash cells once with 8 mL PBS buffer.b.Apply 6 mL of 0.05% trypsin per 15 cm plate.c.Incubate dishes in a 37°C incubator for 5 min and neutralize trypsin with 5 mL of cell culture media.d.Transfer cells from each plate to 15 mL Falcon tubes and collect the cells by centrifugation at 300 g for 3 min.e.Aspirate the supernatant.f.Use 5 mL cell culture media to resuspend pellets in 2 tubes for DMS treatment.g.Snap freeze the cell pellets in the other 2 tubes for the non-DMS treated controls.h.Quickly transfer samples for DMS treatment to the chemical hood. a.Wash cells once with 8 mL PBS buffer. Wash cells once with 8 mL PBS buffer. b.Apply 6 mL of 0.05% trypsin per 15 cm plate. Apply 6 mL of 0.05% trypsin per 15 cm plate. c.Incubate dishes in a 37°C incubator for 5 min and neutralize trypsin with 5 mL of cell culture media. Incubate dishes in a 37°C incubator for 5 min and neutralize trypsin with 5 mL of cell culture media. d.Transfer cells from each plate to 15 mL Falcon tubes and collect the cells by centrifugation at 300 g for 3 min. Transfer cells from each plate to 15 mL Falcon tubes and collect the cells by centrifugation at 300 g for 3 min. e.Aspirate the supernatant. Aspirate the supernatant. f.Use 5 mL cell culture media to resuspend pellets in 2 tubes for DMS treatment. Use 5 mL cell culture media to resuspend pellets in 2 tubes for DMS treatment. g.Snap freeze the cell pellets in the other 2 tubes for the non-DMS treated controls. Snap freeze the cell pellets in the other 2 tubes for the non-DMS treated controls. h.Quickly transfer samples for DMS treatment to the chemical hood. Quickly transfer samples for DMS treatment to the chemical hood. 3.DMS treatment.Note: DMS solution bottle is sealed with a safety cap. Use a needle and syringe to handle the solution.a.Apply 400 μL of 50% DMS in ethanol to each of the 2 tubes.b.Tightly close the Falcon tube caps.c.Hold the tubes with a gloved hand for 7 min, gently inverting the tubes to homogenize the solution. Place the tubes in ice.d.Add 1.3 mL 2-Mercaptoethanol to neutralize the DMS. Gently invert the tubes a few times.e.Spin down cells at 400 g for 3 min at 4°C.f.Discard the supernatant and resuspend the pellet with 5 mL of ice-cold PBS/25% 2-Mercaptoethanol solution.g.Collect cells by centrifugation at 400 g for 3 min at 4°C.h.Repeat the wash in step e-f once.i.Snap-freeze the cells on dry ice, and store at −80°C.Pause point: Cell pellets can be stored at −80°C until RNA extraction.Note: DMS liquid waste could emit toxic fumes. Carefully dispose of the waste into the designated hazardous chemical collection bottles. DMS treatment.Note: DMS solution bottle is sealed with a safety cap. Use a needle and syringe to handle the solution.a.Apply 400 μL of 50% DMS in ethanol to each of the 2 tubes.b.Tightly close the Falcon tube caps.c.Hold the tubes with a gloved hand for 7 min, gently inverting the tubes to homogenize the solution. Place the tubes in ice.d.Add 1.3 mL 2-Mercaptoethanol to neutralize the DMS. Gently invert the tubes a few times.e.Spin down cells at 400 g for 3 min at 4°C.f.Discard the supernatant and resuspend the pellet with 5 mL of ice-cold PBS/25% 2-Mercaptoethanol solution.g.Collect cells by centrifugation at 400 g for 3 min at 4°C.h.Repeat the wash in step e-f once.i.Snap-freeze the cells on dry ice, and store at −80°C.Pause point: Cell pellets can be stored at −80°C until RNA extraction.Note: DMS liquid waste could emit toxic fumes. Carefully dispose of the waste into the designated hazardous chemical collection bottles. Note: DMS solution bottle is sealed with a safety cap. Use a needle and syringe to handle the solution. a.Apply 400 μL of 50% DMS in ethanol to each of the 2 tubes. Apply 400 μL of 50% DMS in ethanol to each of the 2 tubes. b.Tightly close the Falcon tube caps. Tightly close the Falcon tube caps. c.Hold the tubes with a gloved hand for 7 min, gently inverting the tubes to homogenize the solution. Place the tubes in ice. Hold the tubes with a gloved hand for 7 min, gently inverting the tubes to homogenize the solution. Place the tubes in ice. d.Add 1.3 mL 2-Mercaptoethanol to neutralize the DMS. Gently invert the tubes a few times. Add 1.3 mL 2-Mercaptoethanol to neutralize the DMS. Gently invert the tubes a few times. e.Spin down cells at 400 g for 3 min at 4°C. Spin down cells at 400 g for 3 min at 4°C. f.Discard the supernatant and resuspend the pellet with 5 mL of ice-cold PBS/25% 2-Mercaptoethanol solution. Discard the supernatant and resuspend the pellet with 5 mL of ice-cold PBS/25% 2-Mercaptoethanol solution. g.Collect cells by centrifugation at 400 g for 3 min at 4°C. Collect cells by centrifugation at 400 g for 3 min at 4°C. h.Repeat the wash in step e-f once. Repeat the wash in step e-f once. i.Snap-freeze the cells on dry ice, and store at −80°C.Pause point: Cell pellets can be stored at −80°C until RNA extraction.Note: DMS liquid waste could emit toxic fumes. Carefully dispose of the waste into the designated hazardous chemical collection bottles. Snap-freeze the cells on dry ice, and store at −80°C.Pause point: Cell pellets can be stored at −80°C until RNA extraction.Note: DMS liquid waste could emit toxic fumes. Carefully dispose of the waste into the designated hazardous chemical collection bottles. Pause point: Cell pellets can be stored at −80°C until RNA extraction. Note: DMS liquid waste could emit toxic fumes. Carefully dispose of the waste into the designated hazardous chemical collection bottles. Isolation of chromatin-bound fraction Timing: 6–8 h To Focus on RNAs involved in epigenetic regulations, we isolate RNA from the chromatin-bound cell fraction (Figure 1A). However, RNAs in other subcellular fractions could be studied with the following RNA structure analysis. 4.Nuclei isolation.a.Prechill the Nuclei isolation buffers (NIB), NIB-1 and NIB-2, on ice.b.Thaw the ribonucleoside vanadyl complex (RBC) stock solution using 37°C heat block.c.Add RBC stock to the NIB-1 buffer at a 1:20 ratio, as a 10 mM final concentration.d.Add 8 mL of ice-cold NIB-1-RBC buffer to a cell pellet in a Falcon tube and pipet thoroughly to resuspend the cells. Keep the tip of the tube on dry ice while pipetting.CRITICAL: Cell pellets should be kept frozen until they are in contact with the NIB-1 buffer via pipetting. The RNA samples are susceptible to degradation if the cells thaw before resuspension.e.Incubate samples for 5 min on ice.f.Spin down the nucleus at 600 g for 5 min at 4°C.g.Discard the supernatant and resuspend the pellet in 8 mL of cold NIB-2 buffer.h.Collect the isolated nucleus by centrifugation at 600 g for 5 min at 4°C.Note: The supernatant at this step contains the cytoplasmic fraction. Save it to analyze the cytoplasmic RNA structures. Nuclei isolation.a.Prechill the Nuclei isolation buffers (NIB), NIB-1 and NIB-2, on ice.b.Thaw the ribonucleoside vanadyl complex (RBC) stock solution using 37°C heat block.c.Add RBC stock to the NIB-1 buffer at a 1:20 ratio, as a 10 mM final concentration.d.Add 8 mL of ice-cold NIB-1-RBC buffer to a cell pellet in a Falcon tube and pipet thoroughly to resuspend the cells. Keep the tip of the tube on dry ice while pipetting.CRITICAL: Cell pellets should be kept frozen until they are in contact with the NIB-1 buffer via pipetting. The RNA samples are susceptible to degradation if the cells thaw before resuspension.e.Incubate samples for 5 min on ice.f.Spin down the nucleus at 600 g for 5 min at 4°C.g.Discard the supernatant and resuspend the pellet in 8 mL of cold NIB-2 buffer.h.Collect the isolated nucleus by centrifugation at 600 g for 5 min at 4°C.Note: The supernatant at this step contains the cytoplasmic fraction. Save it to analyze the cytoplasmic RNA structures. a.Prechill the Nuclei isolation buffers (NIB), NIB-1 and NIB-2, on ice. Prechill the Nuclei isolation buffers (NIB), NIB-1 and NIB-2, on ice. b.Thaw the ribonucleoside vanadyl complex (RBC) stock solution using 37°C heat block. Thaw the ribonucleoside vanadyl complex (RBC) stock solution using 37°C heat block. c.Add RBC stock to the NIB-1 buffer at a 1:20 ratio, as a 10 mM final concentration. Add RBC stock to the NIB-1 buffer at a 1:20 ratio, as a 10 mM final concentration. d.Add 8 mL of ice-cold NIB-1-RBC buffer to a cell pellet in a Falcon tube and pipet thoroughly to resuspend the cells. Keep the tip of the tube on dry ice while pipetting.CRITICAL: Cell pellets should be kept frozen until they are in contact with the NIB-1 buffer via pipetting. The RNA samples are susceptible to degradation if the cells thaw before resuspension. Add 8 mL of ice-cold NIB-1-RBC buffer to a cell pellet in a Falcon tube and pipet thoroughly to resuspend the cells. Keep the tip of the tube on dry ice while pipetting.CRITICAL: Cell pellets should be kept frozen until they are in contact with the NIB-1 buffer via pipetting. The RNA samples are susceptible to degradation if the cells thaw before resuspension. CRITICAL: Cell pellets should be kept frozen until they are in contact with the NIB-1 buffer via pipetting. The RNA samples are susceptible to degradation if the cells thaw before resuspension. e.Incubate samples for 5 min on ice. Incubate samples for 5 min on ice. f.Spin down the nucleus at 600 g for 5 min at 4°C. Spin down the nucleus at 600 g for 5 min at 4°C. g.Discard the supernatant and resuspend the pellet in 8 mL of cold NIB-2 buffer. Discard the supernatant and resuspend the pellet in 8 mL of cold NIB-2 buffer. h.Collect the isolated nucleus by centrifugation at 600 g for 5 min at 4°C.Note: The supernatant at this step contains the cytoplasmic fraction. Save it to analyze the cytoplasmic RNA structures. Collect the isolated nucleus by centrifugation at 600 g for 5 min at 4°C.Note: The supernatant at this step contains the cytoplasmic fraction. Save it to analyze the cytoplasmic RNA structures. Note: The supernatant at this step contains the cytoplasmic fraction. Save it to analyze the cytoplasmic RNA structures. 5.Extraction of chromatin-bound RNAs.a.Resuspend each nucleus pellet with 250 μL of NaCl, Urea, and Nonidet P-40 (NUN) 1 buffer.17b.Aliquot 200 μL of the nucleus mixture into 2 mL Eppendorf tubes.c.Add 2 mL of NUN2 buffer to each tube.d.Incubate the sample for 15 min on ice. Vortex every 5 min.e.Spin samples at 10000 g for 15 min at 4°C to precipitate the chromatin-bound fraction.f.Remove the supernatant.Note: The supernatant at this step contains the soluble nuclear fraction. Save it to analyze soluble nuclear RNAs.Pause point: Store the pellets at −80°C for up to 4 weeks.g.Add 200 μL of Trizol to each chromatin pellet.h.Freeze for 10 min on dry ice and then thaw at 18 °C–23°C. Repeat this step 3 times.i.Grind the frozen pellet with a microtube pestle until the pellet entirely dissolves in the Trizol reagent.CRITICAL: Ensure the insoluble chromatin pellet is thoroughly resuspended in the Trizol reagent. Insufficient dissolution can result in diminished RNA yield.j.Add 800 μL of Trizol to the mixture, pipet well to mix the solution.k.Incubate for 5 min at 18 °C–23°C. Insoluble chromatin pellets should be well resuspended at this point.l.Add 300 μL of chloroform. Handshake the solution vigorously.Note: Vortexing the samples may damage the integrity of long RNA species.m.Separate the organic and aqueous phases by centrifuging at 10000 × g for 15 min at 4°C.n.Transfer the upper phase to a new 1.5 mL Eppendorf tube.o.Add 500 μL of isopropyl alcohol for RNA precipitation. Mix the solution well with a few inverting.p.Incubate the solution for a minimum of 30 min at −20°C.q.Collect the pellet by centrifugation at 10000 g for 20 min at 4°C.r.Remove the supernatant.s.Wash RNA pellets once with 1 mL of 70% ethanol, repeat the centrifuge.t.Carefully remove the supernatant and air dry the RNA pellet for 5 min.u.Add 50 μl of RNase-free deionized water to dissolve the pellet.CRITICAL: Do not over-dry the RNA pellet. Resuspend the RNA when the pellet starts to become transparent.Note: Check the RNA integrity by gel electrophoresis or microfluidics-based platforms like TapeStation (Figure 1B, first panel).Note: Measure RNA quantity and quality using a UV-spectrophotometer at 260 nm. The RNA yield typically ranges from 250 to 500 μg per isolation with A260/A280 ratio greater than 1.8.Note: 2 × 107 mES cells from a single 15 cm plate typically yield 250–500 μg of chromatin-bound RNA.Note: Test the chromatin-bound RNA enrichment with RT-qPCR assay (Figure 2).v.Select the Poly A + RNA species using NEBNext Poly(A) mRNA Magnetic Isolation Module or Oligotex Direct mRNA kit according to the manufacturer’s instructions.w.Elute the RNA with 20 μl of RNase-free deionized water.Note: To maximize the yield, use step 5p flowthrough for an additional poly A+ capture. In our hands, 250 μg of purified RNA typically yields 3–5 μg of poly A + RNA.Pause point: Store the RNA at −20°C for up to 4 weeks. Extraction of chromatin-bound RNAs.a.Resuspend each nucleus pellet with 250 μL of NaCl, Urea, and Nonidet P-40 (NUN) 1 buffer.17b.Aliquot 200 μL of the nucleus mixture into 2 mL Eppendorf tubes.c.Add 2 mL of NUN2 buffer to each tube.d.Incubate the sample for 15 min on ice. Vortex every 5 min.e.Spin samples at 10000 g for 15 min at 4°C to precipitate the chromatin-bound fraction.f.Remove the supernatant.Note: The supernatant at this step contains the soluble nuclear fraction. Save it to analyze soluble nuclear RNAs.Pause point: Store the pellets at −80°C for up to 4 weeks.g.Add 200 μL of Trizol to each chromatin pellet.h.Freeze for 10 min on dry ice and then thaw at 18 °C–23°C. Repeat this step 3 times.i.Grind the frozen pellet with a microtube pestle until the pellet entirely dissolves in the Trizol reagent.CRITICAL: Ensure the insoluble chromatin pellet is thoroughly resuspended in the Trizol reagent. Insufficient dissolution can result in diminished RNA yield.j.Add 800 μL of Trizol to the mixture, pipet well to mix the solution.k.Incubate for 5 min at 18 °C–23°C. Insoluble chromatin pellets should be well resuspended at this point.l.Add 300 μL of chloroform. Handshake the solution vigorously.Note: Vortexing the samples may damage the integrity of long RNA species.m.Separate the organic and aqueous phases by centrifuging at 10000 × g for 15 min at 4°C.n.Transfer the upper phase to a new 1.5 mL Eppendorf tube.o.Add 500 μL of isopropyl alcohol for RNA precipitation. Mix the solution well with a few inverting.p.Incubate the solution for a minimum of 30 min at −20°C.q.Collect the pellet by centrifugation at 10000 g for 20 min at 4°C.r.Remove the supernatant.s.Wash RNA pellets once with 1 mL of 70% ethanol, repeat the centrifuge.t.Carefully remove the supernatant and air dry the RNA pellet for 5 min.u.Add 50 μl of RNase-free deionized water to dissolve the pellet.CRITICAL: Do not over-dry the RNA pellet. Resuspend the RNA when the pellet starts to become transparent.Note: Check the RNA integrity by gel electrophoresis or microfluidics-based platforms like TapeStation (Figure 1B, first panel).Note: Measure RNA quantity and quality using a UV-spectrophotometer at 260 nm. The RNA yield typically ranges from 250 to 500 μg per isolation with A260/A280 ratio greater than 1.8.Note: 2 × 107 mES cells from a single 15 cm plate typically yield 250–500 μg of chromatin-bound RNA.Note: Test the chromatin-bound RNA enrichment with RT-qPCR assay (Figure 2).v.Select the Poly A + RNA species using NEBNext Poly(A) mRNA Magnetic Isolation Module or Oligotex Direct mRNA kit according to the manufacturer’s instructions.w.Elute the RNA with 20 μl of RNase-free deionized water.Note: To maximize the yield, use step 5p flowthrough for an additional poly A+ capture. In our hands, 250 μg of purified RNA typically yields 3–5 μg of poly A + RNA.Pause point: Store the RNA at −20°C for up to 4 weeks. a.Resuspend each nucleus pellet with 250 μL of NaCl, Urea, and Nonidet P-40 (NUN) 1 buffer.17 Resuspend each nucleus pellet with 250 μL of NaCl, Urea, and Nonidet P-40 (NUN) 1 buffer.17 b.Aliquot 200 μL of the nucleus mixture into 2 mL Eppendorf tubes. Aliquot 200 μL of the nucleus mixture into 2 mL Eppendorf tubes. c.Add 2 mL of NUN2 buffer to each tube. Add 2 mL of NUN2 buffer to each tube. d.Incubate the sample for 15 min on ice. Vortex every 5 min. Incubate the sample for 15 min on ice. Vortex every 5 min. e.Spin samples at 10000 g for 15 min at 4°C to precipitate the chromatin-bound fraction. Spin samples at 10000 g for 15 min at 4°C to precipitate the chromatin-bound fraction. f.Remove the supernatant.Note: The supernatant at this step contains the soluble nuclear fraction. Save it to analyze soluble nuclear RNAs.Pause point: Store the pellets at −80°C for up to 4 weeks. Remove the supernatant.Note: The supernatant at this step contains the soluble nuclear fraction. Save it to analyze soluble nuclear RNAs.Pause point: Store the pellets at −80°C for up to 4 weeks. Note: The supernatant at this step contains the soluble nuclear fraction. Save it to analyze soluble nuclear RNAs. Pause point: Store the pellets at −80°C for up to 4 weeks. g.Add 200 μL of Trizol to each chromatin pellet. Add 200 μL of Trizol to each chromatin pellet. h.Freeze for 10 min on dry ice and then thaw at 18 °C–23°C. Repeat this step 3 times. Freeze for 10 min on dry ice and then thaw at 18 °C–23°C. Repeat this step 3 times. i.Grind the frozen pellet with a microtube pestle until the pellet entirely dissolves in the Trizol reagent.CRITICAL: Ensure the insoluble chromatin pellet is thoroughly resuspended in the Trizol reagent. Insufficient dissolution can result in diminished RNA yield. Grind the frozen pellet with a microtube pestle until the pellet entirely dissolves in the Trizol reagent.CRITICAL: Ensure the insoluble chromatin pellet is thoroughly resuspended in the Trizol reagent. Insufficient dissolution can result in diminished RNA yield. CRITICAL: Ensure the insoluble chromatin pellet is thoroughly resuspended in the Trizol reagent. Insufficient dissolution can result in diminished RNA yield. j.Add 800 μL of Trizol to the mixture, pipet well to mix the solution. Add 800 μL of Trizol to the mixture, pipet well to mix the solution. k.Incubate for 5 min at 18 °C–23°C. Insoluble chromatin pellets should be well resuspended at this point. Incubate for 5 min at 18 °C–23°C. Insoluble chromatin pellets should be well resuspended at this point. l.Add 300 μL of chloroform. Handshake the solution vigorously.Note: Vortexing the samples may damage the integrity of long RNA species. Add 300 μL of chloroform. Handshake the solution vigorously.Note: Vortexing the samples may damage the integrity of long RNA species. Note: Vortexing the samples may damage the integrity of long RNA species. m.Separate the organic and aqueous phases by centrifuging at 10000 × g for 15 min at 4°C. Separate the organic and aqueous phases by centrifuging at 10000 × g for 15 min at 4°C. n.Transfer the upper phase to a new 1.5 mL Eppendorf tube. Transfer the upper phase to a new 1.5 mL Eppendorf tube. o.Add 500 μL of isopropyl alcohol for RNA precipitation. Mix the solution well with a few inverting. Add 500 μL of isopropyl alcohol for RNA precipitation. Mix the solution well with a few inverting. p.Incubate the solution for a minimum of 30 min at −20°C. Incubate the solution for a minimum of 30 min at −20°C. q.Collect the pellet by centrifugation at 10000 g for 20 min at 4°C. Collect the pellet by centrifugation at 10000 g for 20 min at 4°C. r.Remove the supernatant. Remove the supernatant. s.Wash RNA pellets once with 1 mL of 70% ethanol, repeat the centrifuge. Wash RNA pellets once with 1 mL of 70% ethanol, repeat the centrifuge. t.Carefully remove the supernatant and air dry the RNA pellet for 5 min. Carefully remove the supernatant and air dry the RNA pellet for 5 min. u.Add 50 μl of RNase-free deionized water to dissolve the pellet.CRITICAL: Do not over-dry the RNA pellet. Resuspend the RNA when the pellet starts to become transparent.Note: Check the RNA integrity by gel electrophoresis or microfluidics-based platforms like TapeStation (Figure 1B, first panel).Note: Measure RNA quantity and quality using a UV-spectrophotometer at 260 nm. The RNA yield typically ranges from 250 to 500 μg per isolation with A260/A280 ratio greater than 1.8.Note: 2 × 107 mES cells from a single 15 cm plate typically yield 250–500 μg of chromatin-bound RNA.Note: Test the chromatin-bound RNA enrichment with RT-qPCR assay (Figure 2). Add 50 μl of RNase-free deionized water to dissolve the pellet.CRITICAL: Do not over-dry the RNA pellet. Resuspend the RNA when the pellet starts to become transparent.Note: Check the RNA integrity by gel electrophoresis or microfluidics-based platforms like TapeStation (Figure 1B, first panel).Note: Measure RNA quantity and quality using a UV-spectrophotometer at 260 nm. The RNA yield typically ranges from 250 to 500 μg per isolation with A260/A280 ratio greater than 1.8.Note: 2 × 107 mES cells from a single 15 cm plate typically yield 250–500 μg of chromatin-bound RNA.Note: Test the chromatin-bound RNA enrichment with RT-qPCR assay (Figure 2). CRITICAL: Do not over-dry the RNA pellet. Resuspend the RNA when the pellet starts to become transparent. Note: Check the RNA integrity by gel electrophoresis or microfluidics-based platforms like TapeStation (Figure 1B, first panel). Note: Measure RNA quantity and quality using a UV-spectrophotometer at 260 nm. The RNA yield typically ranges from 250 to 500 μg per isolation with A260/A280 ratio greater than 1.8. Note: 2 × 107 mES cells from a single 15 cm plate typically yield 250–500 μg of chromatin-bound RNA. Note: Test the chromatin-bound RNA enrichment with RT-qPCR assay (Figure 2). v.Select the Poly A + RNA species using NEBNext Poly(A) mRNA Magnetic Isolation Module or Oligotex Direct mRNA kit according to the manufacturer’s instructions. Select the Poly A + RNA species using NEBNext Poly(A) mRNA Magnetic Isolation Module or Oligotex Direct mRNA kit according to the manufacturer’s instructions. w.Elute the RNA with 20 μl of RNase-free deionized water.Note: To maximize the yield, use step 5p flowthrough for an additional poly A+ capture. In our hands, 250 μg of purified RNA typically yields 3–5 μg of poly A + RNA.Pause point: Store the RNA at −20°C for up to 4 weeks. Elute the RNA with 20 μl of RNase-free deionized water.Note: To maximize the yield, use step 5p flowthrough for an additional poly A+ capture. In our hands, 250 μg of purified RNA typically yields 3–5 μg of poly A + RNA.Pause point: Store the RNA at −20°C for up to 4 weeks. Note: To maximize the yield, use step 5p flowthrough for an additional poly A+ capture. In our hands, 250 μg of purified RNA typically yields 3–5 μg of poly A + RNA. Pause point: Store the RNA at −20°C for up to 4 weeks. Subcellular fractionation selectively enriches chromatin-bound long non-coding RNAs Relative amounts of Actb intron, Xist, TERRA, Malat1, and Actb RNAs are analyzed in the indicated subcellular fractions. Error bars on the graph indicate the standard deviation of triplicates. Reverse transcription (RT)-Stop library preparation Timing: 4 days G-quadruplex structure formation is K+ dependent and causes reverse transcriptase to stall (RT-stop) at the 3′ end of the rG4 motifs. Therefore, frequent RT-stop sites in the presence of K+ can be interpreted as signatures of rG4 structure formation. In control reactions, Li+ is used to balance the ion concentration instead of K+. To create a comprehensive map of global RNA structure patterns, RNA samples are prepared from DMS-treated and untreated cells and then subjected to reverse transcription in K+ and Li+ buffers. This combination of sample conditions enables the study of both rG4 and RNA duplex structures. 6.Chemical RNA fragmentation.a.Dilute 3–5 μg of isolated poly A+ chromatin-bound RNA in 50 μL of 1x RNA fragmentation buffer.b.Incubate the tube for 7 min in a 95°C heat block.c.Run 1 μL of the mixture in 8% acrylamide-urea denaturing gel.d.Visualize the RNA fragmentation level with 1:10000 SYBR gold staining.Note: In case of insufficient fragmentation, extend the heat treatment time as needed.e.Precipitate the fragmented RNA.i.Add 5 μL of 3M Sodium acetate (pH 5.5), 25 μg glycogen, and 150 μL of 100% ethanol.ii.Centrifuge the tube at 10000 × g for 20 min at 4°C.iii.Wash the RNA pellet with 70% ethanol once and briefly dry the pellet.iv.Resuspend the RNA pellet in 4 μL of RNase-free water.f.RNA size fractionation.i.Mix the fragmented RNA solution with 4 μL of 2x Urea loading buffer.ii.Denature the RNA for 3 min at 80°C.iii.Run the entire sample volume in a preheated 8% acrylamide-urea denaturing gel along with the RNA size markers.iv.Stain the gel with 1:10000 SYBR gold in 1x TBE for 15 min.v.Excise the band referring to 60–80 nt in length (Figure 1B).CRITICAL: Do not over-run the gel to minimize the excised gel size. Excess gel size diminishes the yield of RNA purification.Note: This initial size fractionation allows for the isolation of RT-stop product over fully synthesized cDNA by using size-based gel elution procedures in the following steps.Note: RNAs shorter than 60–80 nt cannot be analyzed with this protocol.vi.Stain the gel with 1:10000 SYBR gold in 1x TBE for 15 min.vii.Excise the band referring to 60–80 nt in length (Figure 1B).viii.Recover the RNA using the ZR small-RNA PAGE Recovery Kit.Note: Crush the gel bands in RNA recovery buffer and incubate the samples at 18 °C–23°C for 12 h to improve RNA diffusion into the buffer.ix.Elute the RNA with 7 μL of RNase-free deionized water.Pause point: Store the RNA at −20°C up to 4 weeks. Chemical RNA fragmentation.a.Dilute 3–5 μg of isolated poly A+ chromatin-bound RNA in 50 μL of 1x RNA fragmentation buffer.b.Incubate the tube for 7 min in a 95°C heat block.c.Run 1 μL of the mixture in 8% acrylamide-urea denaturing gel.d.Visualize the RNA fragmentation level with 1:10000 SYBR gold staining.Note: In case of insufficient fragmentation, extend the heat treatment time as needed.e.Precipitate the fragmented RNA.i.Add 5 μL of 3M Sodium acetate (pH 5.5), 25 μg glycogen, and 150 μL of 100% ethanol.ii.Centrifuge the tube at 10000 × g for 20 min at 4°C.iii.Wash the RNA pellet with 70% ethanol once and briefly dry the pellet.iv.Resuspend the RNA pellet in 4 μL of RNase-free water.f.RNA size fractionation.i.Mix the fragmented RNA solution with 4 μL of 2x Urea loading buffer.ii.Denature the RNA for 3 min at 80°C.iii.Run the entire sample volume in a preheated 8% acrylamide-urea denaturing gel along with the RNA size markers.iv.Stain the gel with 1:10000 SYBR gold in 1x TBE for 15 min.v.Excise the band referring to 60–80 nt in length (Figure 1B).CRITICAL: Do not over-run the gel to minimize the excised gel size. Excess gel size diminishes the yield of RNA purification.Note: This initial size fractionation allows for the isolation of RT-stop product over fully synthesized cDNA by using size-based gel elution procedures in the following steps.Note: RNAs shorter than 60–80 nt cannot be analyzed with this protocol.vi.Stain the gel with 1:10000 SYBR gold in 1x TBE for 15 min.vii.Excise the band referring to 60–80 nt in length (Figure 1B).viii.Recover the RNA using the ZR small-RNA PAGE Recovery Kit.Note: Crush the gel bands in RNA recovery buffer and incubate the samples at 18 °C–23°C for 12 h to improve RNA diffusion into the buffer.ix.Elute the RNA with 7 μL of RNase-free deionized water.Pause point: Store the RNA at −20°C up to 4 weeks. a.Dilute 3–5 μg of isolated poly A+ chromatin-bound RNA in 50 μL of 1x RNA fragmentation buffer. Dilute 3–5 μg of isolated poly A+ chromatin-bound RNA in 50 μL of 1x RNA fragmentation buffer. b.Incubate the tube for 7 min in a 95°C heat block. Incubate the tube for 7 min in a 95°C heat block. c.Run 1 μL of the mixture in 8% acrylamide-urea denaturing gel. Run 1 μL of the mixture in 8% acrylamide-urea denaturing gel. d.Visualize the RNA fragmentation level with 1:10000 SYBR gold staining.Note: In case of insufficient fragmentation, extend the heat treatment time as needed. Visualize the RNA fragmentation level with 1:10000 SYBR gold staining.Note: In case of insufficient fragmentation, extend the heat treatment time as needed. Note: In case of insufficient fragmentation, extend the heat treatment time as needed. e.Precipitate the fragmented RNA.i.Add 5 μL of 3M Sodium acetate (pH 5.5), 25 μg glycogen, and 150 μL of 100% ethanol.ii.Centrifuge the tube at 10000 × g for 20 min at 4°C.iii.Wash the RNA pellet with 70% ethanol once and briefly dry the pellet.iv.Resuspend the RNA pellet in 4 μL of RNase-free water. Precipitate the fragmented RNA.i.Add 5 μL of 3M Sodium acetate (pH 5.5), 25 μg glycogen, and 150 μL of 100% ethanol.ii.Centrifuge the tube at 10000 × g for 20 min at 4°C.iii.Wash the RNA pellet with 70% ethanol once and briefly dry the pellet.iv.Resuspend the RNA pellet in 4 μL of RNase-free water. i.Add 5 μL of 3M Sodium acetate (pH 5.5), 25 μg glycogen, and 150 μL of 100% ethanol. Add 5 μL of 3M Sodium acetate (pH 5.5), 25 μg glycogen, and 150 μL of 100% ethanol. ii.Centrifuge the tube at 10000 × g for 20 min at 4°C. Centrifuge the tube at 10000 × g for 20 min at 4°C. iii.Wash the RNA pellet with 70% ethanol once and briefly dry the pellet. Wash the RNA pellet with 70% ethanol once and briefly dry the pellet. iv.Resuspend the RNA pellet in 4 μL of RNase-free water. Resuspend the RNA pellet in 4 μL of RNase-free water. f.RNA size fractionation.i.Mix the fragmented RNA solution with 4 μL of 2x Urea loading buffer.ii.Denature the RNA for 3 min at 80°C.iii.Run the entire sample volume in a preheated 8% acrylamide-urea denaturing gel along with the RNA size markers.iv.Stain the gel with 1:10000 SYBR gold in 1x TBE for 15 min.v.Excise the band referring to 60–80 nt in length (Figure 1B).CRITICAL: Do not over-run the gel to minimize the excised gel size. Excess gel size diminishes the yield of RNA purification.Note: This initial size fractionation allows for the isolation of RT-stop product over fully synthesized cDNA by using size-based gel elution procedures in the following steps.Note: RNAs shorter than 60–80 nt cannot be analyzed with this protocol.vi.Stain the gel with 1:10000 SYBR gold in 1x TBE for 15 min.vii.Excise the band referring to 60–80 nt in length (Figure 1B).viii.Recover the RNA using the ZR small-RNA PAGE Recovery Kit.Note: Crush the gel bands in RNA recovery buffer and incubate the samples at 18 °C–23°C for 12 h to improve RNA diffusion into the buffer.ix.Elute the RNA with 7 μL of RNase-free deionized water.Pause point: Store the RNA at −20°C up to 4 weeks. RNA size fractionation.i.Mix the fragmented RNA solution with 4 μL of 2x Urea loading buffer.ii.Denature the RNA for 3 min at 80°C.iii.Run the entire sample volume in a preheated 8% acrylamide-urea denaturing gel along with the RNA size markers.iv.Stain the gel with 1:10000 SYBR gold in 1x TBE for 15 min.v.Excise the band referring to 60–80 nt in length (Figure 1B).CRITICAL: Do not over-run the gel to minimize the excised gel size. Excess gel size diminishes the yield of RNA purification.Note: This initial size fractionation allows for the isolation of RT-stop product over fully synthesized cDNA by using size-based gel elution procedures in the following steps.Note: RNAs shorter than 60–80 nt cannot be analyzed with this protocol.vi.Stain the gel with 1:10000 SYBR gold in 1x TBE for 15 min.vii.Excise the band referring to 60–80 nt in length (Figure 1B).viii.Recover the RNA using the ZR small-RNA PAGE Recovery Kit.Note: Crush the gel bands in RNA recovery buffer and incubate the samples at 18 °C–23°C for 12 h to improve RNA diffusion into the buffer.ix.Elute the RNA with 7 μL of RNase-free deionized water.Pause point: Store the RNA at −20°C up to 4 weeks. i.Mix the fragmented RNA solution with 4 μL of 2x Urea loading buffer. Mix the fragmented RNA solution with 4 μL of 2x Urea loading buffer. ii.Denature the RNA for 3 min at 80°C. Denature the RNA for 3 min at 80°C. iii.Run the entire sample volume in a preheated 8% acrylamide-urea denaturing gel along with the RNA size markers. Run the entire sample volume in a preheated 8% acrylamide-urea denaturing gel along with the RNA size markers. iv.Stain the gel with 1:10000 SYBR gold in 1x TBE for 15 min. Stain the gel with 1:10000 SYBR gold in 1x TBE for 15 min. v.Excise the band referring to 60–80 nt in length (Figure 1B).CRITICAL: Do not over-run the gel to minimize the excised gel size. Excess gel size diminishes the yield of RNA purification.Note: This initial size fractionation allows for the isolation of RT-stop product over fully synthesized cDNA by using size-based gel elution procedures in the following steps.Note: RNAs shorter than 60–80 nt cannot be analyzed with this protocol. Excise the band referring to 60–80 nt in length (Figure 1B).CRITICAL: Do not over-run the gel to minimize the excised gel size. Excess gel size diminishes the yield of RNA purification.Note: This initial size fractionation allows for the isolation of RT-stop product over fully synthesized cDNA by using size-based gel elution procedures in the following steps.Note: RNAs shorter than 60–80 nt cannot be analyzed with this protocol. CRITICAL: Do not over-run the gel to minimize the excised gel size. Excess gel size diminishes the yield of RNA purification. Note: This initial size fractionation allows for the isolation of RT-stop product over fully synthesized cDNA by using size-based gel elution procedures in the following steps. Note: RNAs shorter than 60–80 nt cannot be analyzed with this protocol. vi.Stain the gel with 1:10000 SYBR gold in 1x TBE for 15 min. Stain the gel with 1:10000 SYBR gold in 1x TBE for 15 min. vii.Excise the band referring to 60–80 nt in length (Figure 1B). Excise the band referring to 60–80 nt in length (Figure 1B). viii.Recover the RNA using the ZR small-RNA PAGE Recovery Kit.Note: Crush the gel bands in RNA recovery buffer and incubate the samples at 18 °C–23°C for 12 h to improve RNA diffusion into the buffer. Recover the RNA using the ZR small-RNA PAGE Recovery Kit.Note: Crush the gel bands in RNA recovery buffer and incubate the samples at 18 °C–23°C for 12 h to improve RNA diffusion into the buffer. Note: Crush the gel bands in RNA recovery buffer and incubate the samples at 18 °C–23°C for 12 h to improve RNA diffusion into the buffer. ix.Elute the RNA with 7 μL of RNase-free deionized water.Pause point: Store the RNA at −20°C up to 4 weeks. Elute the RNA with 7 μL of RNase-free deionized water.Pause point: Store the RNA at −20°C up to 4 weeks. Pause point: Store the RNA at −20°C up to 4 weeks. 7.RNA 3′ Dephosphorylation.a.In a RNase-free PCR tube, combine 1 μL of 10x T4 RNA ligase buffer, 1.5 μL of T4 polynucleotide kinase, 0.5 μL of RNase inhibitor with the 7 μL RNA solution.b.Incubate 5 h at 37°C. RNA 3′ Dephosphorylation.a.In a RNase-free PCR tube, combine 1 μL of 10x T4 RNA ligase buffer, 1.5 μL of T4 polynucleotide kinase, 0.5 μL of RNase inhibitor with the 7 μL RNA solution.b.Incubate 5 h at 37°C. a.In a RNase-free PCR tube, combine 1 μL of 10x T4 RNA ligase buffer, 1.5 μL of T4 polynucleotide kinase, 0.5 μL of RNase inhibitor with the 7 μL RNA solution. In a RNase-free PCR tube, combine 1 μL of 10x T4 RNA ligase buffer, 1.5 μL of T4 polynucleotide kinase, 0.5 μL of RNase inhibitor with the 7 μL RNA solution. b.Incubate 5 h at 37°C. Incubate 5 h at 37°C. 8.Adaptor Ligation.a.Add 1 μL of 10x T4 RNA ligase buffer, 6 μL of 50% PEG8000, 2 μL of 20 μM 5′ adenylated 3 DNA adapter, and 1 μL of T4 RNA ligase2-truncated K227Q to the RNA 3′ dephosphorylation reaction mix.b.Incubate for 18 h at 16°C.c.Precipitate the adaptor-ligated RNA.i.Add 2 μL of 3M Sodium acetate (pH 5.5), 25 μg glycogen, and 60 μL of 100% ethanol to the ligation mixture.ii.Centrifuge at 10000 × g for 20 min at 4°C.iii.Wash the RNA pellet with 70% ethanol once, briefly dry the pellet, and resuspend in 4 μL of RNase-free water.d.RNA size fractionation.i.Run samples in 8% acrylamide-urea denaturing gel.ii.Stain the gel with 1:10000 SYBR gold in 1x TBE for 15 min.iii.Excise the RNA band 85–105 nt in length (Figure 1B).iv.Recover the adaptor-ligated RNA with the ZR small-RNA PAGE Recovery Kit. Elute the RNA with 6 μL of RNase-free deionized water. Adaptor Ligation.a.Add 1 μL of 10x T4 RNA ligase buffer, 6 μL of 50% PEG8000, 2 μL of 20 μM 5′ adenylated 3 DNA adapter, and 1 μL of T4 RNA ligase2-truncated K227Q to the RNA 3′ dephosphorylation reaction mix.b.Incubate for 18 h at 16°C.c.Precipitate the adaptor-ligated RNA.i.Add 2 μL of 3M Sodium acetate (pH 5.5), 25 μg glycogen, and 60 μL of 100% ethanol to the ligation mixture.ii.Centrifuge at 10000 × g for 20 min at 4°C.iii.Wash the RNA pellet with 70% ethanol once, briefly dry the pellet, and resuspend in 4 μL of RNase-free water.d.RNA size fractionation.i.Run samples in 8% acrylamide-urea denaturing gel.ii.Stain the gel with 1:10000 SYBR gold in 1x TBE for 15 min.iii.Excise the RNA band 85–105 nt in length (Figure 1B).iv.Recover the adaptor-ligated RNA with the ZR small-RNA PAGE Recovery Kit. Elute the RNA with 6 μL of RNase-free deionized water. a.Add 1 μL of 10x T4 RNA ligase buffer, 6 μL of 50% PEG8000, 2 μL of 20 μM 5′ adenylated 3 DNA adapter, and 1 μL of T4 RNA ligase2-truncated K227Q to the RNA 3′ dephosphorylation reaction mix. Add 1 μL of 10x T4 RNA ligase buffer, 6 μL of 50% PEG8000, 2 μL of 20 μM 5′ adenylated 3 DNA adapter, and 1 μL of T4 RNA ligase2-truncated K227Q to the RNA 3′ dephosphorylation reaction mix. b.Incubate for 18 h at 16°C. Incubate for 18 h at 16°C. c.Precipitate the adaptor-ligated RNA.i.Add 2 μL of 3M Sodium acetate (pH 5.5), 25 μg glycogen, and 60 μL of 100% ethanol to the ligation mixture.ii.Centrifuge at 10000 × g for 20 min at 4°C.iii.Wash the RNA pellet with 70% ethanol once, briefly dry the pellet, and resuspend in 4 μL of RNase-free water. Precipitate the adaptor-ligated RNA.i.Add 2 μL of 3M Sodium acetate (pH 5.5), 25 μg glycogen, and 60 μL of 100% ethanol to the ligation mixture.ii.Centrifuge at 10000 × g for 20 min at 4°C.iii.Wash the RNA pellet with 70% ethanol once, briefly dry the pellet, and resuspend in 4 μL of RNase-free water. i.Add 2 μL of 3M Sodium acetate (pH 5.5), 25 μg glycogen, and 60 μL of 100% ethanol to the ligation mixture. Add 2 μL of 3M Sodium acetate (pH 5.5), 25 μg glycogen, and 60 μL of 100% ethanol to the ligation mixture. ii.Centrifuge at 10000 × g for 20 min at 4°C. Centrifuge at 10000 × g for 20 min at 4°C. iii.Wash the RNA pellet with 70% ethanol once, briefly dry the pellet, and resuspend in 4 μL of RNase-free water. Wash the RNA pellet with 70% ethanol once, briefly dry the pellet, and resuspend in 4 μL of RNase-free water. d.RNA size fractionation.i.Run samples in 8% acrylamide-urea denaturing gel.ii.Stain the gel with 1:10000 SYBR gold in 1x TBE for 15 min.iii.Excise the RNA band 85–105 nt in length (Figure 1B).iv.Recover the adaptor-ligated RNA with the ZR small-RNA PAGE Recovery Kit. Elute the RNA with 6 μL of RNase-free deionized water. RNA size fractionation.i.Run samples in 8% acrylamide-urea denaturing gel.ii.Stain the gel with 1:10000 SYBR gold in 1x TBE for 15 min.iii.Excise the RNA band 85–105 nt in length (Figure 1B).iv.Recover the adaptor-ligated RNA with the ZR small-RNA PAGE Recovery Kit. Elute the RNA with 6 μL of RNase-free deionized water. i.Run samples in 8% acrylamide-urea denaturing gel. Run samples in 8% acrylamide-urea denaturing gel. ii.Stain the gel with 1:10000 SYBR gold in 1x TBE for 15 min. Stain the gel with 1:10000 SYBR gold in 1x TBE for 15 min. iii.Excise the RNA band 85–105 nt in length (Figure 1B). Excise the RNA band 85–105 nt in length (Figure 1B). iv.Recover the adaptor-ligated RNA with the ZR small-RNA PAGE Recovery Kit. Elute the RNA with 6 μL of RNase-free deionized water. Recover the adaptor-ligated RNA with the ZR small-RNA PAGE Recovery Kit. Elute the RNA with 6 μL of RNase-free deionized water. Pause point: Store the RNA at −20°C up to 4 weeks. 9.Reverse Transcription of the Adaptor-Ligated RNA.a.Set up the RT reactions by combining 6 μL of Adaptor-ligated RNA, 4 μL of 5x RT buffer (K+ or Li+), 2 μL of 5′ phosphorylated iSp18 PE Reverse oligo, 1 μL of 10 mM dNTP, 0.2 μL of RNase inhibitor, and 7 μL of RNase-free deionized water.Note: In this step, each test consists of four RT reactions: DMS positive and DMS negative samples, combined with K+ or Li+ RT buffers.b.Program the PCR machine with the following conditions: 80°C for 2 min, 42°C for 5 min, and 42°C for 10 min.c.Preheat the PCR block to 80°C and hold while preparing RT reaction mixtures.d.Hold the process after the second 42°C for 5 min step and add 1 μL of 0.1 M DTT and 100 units of Superscript III.e.Once the reaction is complete, quickly chill the PCR tubes on ice.f.Add 2 μL of 1 M NaOH in each tube and apply heating at 95°C for 10 min.g.After heating, place the tube on ice and neutralize the solution by adding 2 μL of 1 M HCl.Note: This step removes the remaining RNA templates.h.Precipitate the RT product.i.Add 2 μL of 3M Sodium acetate (pH 5.5), 25 μg glycogen, and 60 μL of 100% ethanol.ii.Centrifuge the tube at 10000 × g for 20 min at 4°C.iii.Wash the nucleic acid pellet with 70% ethanol once, briefly dry the pellet, and resuspend in 4 μL of deionized water.i.Run the entire volume of the samples on 8% acrylamide-urea denaturing gel.j.Stain the gel with 1:10000 SYBR gold in 1x TBE for 15 min.k.Excise the band 75–105 nt in length. RT-stop products appear as smearing under the band of fully extended RT products (Figure 1B).l.Purify the cDNA with the ZR small-RNA PAGE Recovery Kit.Pause point: Store the samples at −20°C up to 4 weeks. Reverse Transcription of the Adaptor-Ligated RNA.a.Set up the RT reactions by combining 6 μL of Adaptor-ligated RNA, 4 μL of 5x RT buffer (K+ or Li+), 2 μL of 5′ phosphorylated iSp18 PE Reverse oligo, 1 μL of 10 mM dNTP, 0.2 μL of RNase inhibitor, and 7 μL of RNase-free deionized water.Note: In this step, each test consists of four RT reactions: DMS positive and DMS negative samples, combined with K+ or Li+ RT buffers.b.Program the PCR machine with the following conditions: 80°C for 2 min, 42°C for 5 min, and 42°C for 10 min.c.Preheat the PCR block to 80°C and hold while preparing RT reaction mixtures.d.Hold the process after the second 42°C for 5 min step and add 1 μL of 0.1 M DTT and 100 units of Superscript III.e.Once the reaction is complete, quickly chill the PCR tubes on ice.f.Add 2 μL of 1 M NaOH in each tube and apply heating at 95°C for 10 min.g.After heating, place the tube on ice and neutralize the solution by adding 2 μL of 1 M HCl.Note: This step removes the remaining RNA templates.h.Precipitate the RT product.i.Add 2 μL of 3M Sodium acetate (pH 5.5), 25 μg glycogen, and 60 μL of 100% ethanol.ii.Centrifuge the tube at 10000 × g for 20 min at 4°C.iii.Wash the nucleic acid pellet with 70% ethanol once, briefly dry the pellet, and resuspend in 4 μL of deionized water.i.Run the entire volume of the samples on 8% acrylamide-urea denaturing gel.j.Stain the gel with 1:10000 SYBR gold in 1x TBE for 15 min.k.Excise the band 75–105 nt in length. RT-stop products appear as smearing under the band of fully extended RT products (Figure 1B).l.Purify the cDNA with the ZR small-RNA PAGE Recovery Kit.Pause point: Store the samples at −20°C up to 4 weeks. a.Set up the RT reactions by combining 6 μL of Adaptor-ligated RNA, 4 μL of 5x RT buffer (K+ or Li+), 2 μL of 5′ phosphorylated iSp18 PE Reverse oligo, 1 μL of 10 mM dNTP, 0.2 μL of RNase inhibitor, and 7 μL of RNase-free deionized water.Note: In this step, each test consists of four RT reactions: DMS positive and DMS negative samples, combined with K+ or Li+ RT buffers. Set up the RT reactions by combining 6 μL of Adaptor-ligated RNA, 4 μL of 5x RT buffer (K+ or Li+), 2 μL of 5′ phosphorylated iSp18 PE Reverse oligo, 1 μL of 10 mM dNTP, 0.2 μL of RNase inhibitor, and 7 μL of RNase-free deionized water.Note: In this step, each test consists of four RT reactions: DMS positive and DMS negative samples, combined with K+ or Li+ RT buffers. Note: In this step, each test consists of four RT reactions: DMS positive and DMS negative samples, combined with K+ or Li+ RT buffers. b.Program the PCR machine with the following conditions: 80°C for 2 min, 42°C for 5 min, and 42°C for 10 min. Program the PCR machine with the following conditions: 80°C for 2 min, 42°C for 5 min, and 42°C for 10 min. c.Preheat the PCR block to 80°C and hold while preparing RT reaction mixtures. Preheat the PCR block to 80°C and hold while preparing RT reaction mixtures. d.Hold the process after the second 42°C for 5 min step and add 1 μL of 0.1 M DTT and 100 units of Superscript III. Hold the process after the second 42°C for 5 min step and add 1 μL of 0.1 M DTT and 100 units of Superscript III. e.Once the reaction is complete, quickly chill the PCR tubes on ice. Once the reaction is complete, quickly chill the PCR tubes on ice. f.Add 2 μL of 1 M NaOH in each tube and apply heating at 95°C for 10 min. Add 2 μL of 1 M NaOH in each tube and apply heating at 95°C for 10 min. g.After heating, place the tube on ice and neutralize the solution by adding 2 μL of 1 M HCl.Note: This step removes the remaining RNA templates. After heating, place the tube on ice and neutralize the solution by adding 2 μL of 1 M HCl.Note: This step removes the remaining RNA templates. Note: This step removes the remaining RNA templates. h.Precipitate the RT product.i.Add 2 μL of 3M Sodium acetate (pH 5.5), 25 μg glycogen, and 60 μL of 100% ethanol.ii.Centrifuge the tube at 10000 × g for 20 min at 4°C.iii.Wash the nucleic acid pellet with 70% ethanol once, briefly dry the pellet, and resuspend in 4 μL of deionized water. Precipitate the RT product.i.Add 2 μL of 3M Sodium acetate (pH 5.5), 25 μg glycogen, and 60 μL of 100% ethanol.ii.Centrifuge the tube at 10000 × g for 20 min at 4°C.iii.Wash the nucleic acid pellet with 70% ethanol once, briefly dry the pellet, and resuspend in 4 μL of deionized water. i.Add 2 μL of 3M Sodium acetate (pH 5.5), 25 μg glycogen, and 60 μL of 100% ethanol. Add 2 μL of 3M Sodium acetate (pH 5.5), 25 μg glycogen, and 60 μL of 100% ethanol. ii.Centrifuge the tube at 10000 × g for 20 min at 4°C. Centrifuge the tube at 10000 × g for 20 min at 4°C. iii.Wash the nucleic acid pellet with 70% ethanol once, briefly dry the pellet, and resuspend in 4 μL of deionized water. Wash the nucleic acid pellet with 70% ethanol once, briefly dry the pellet, and resuspend in 4 μL of deionized water. i.Run the entire volume of the samples on 8% acrylamide-urea denaturing gel. Run the entire volume of the samples on 8% acrylamide-urea denaturing gel. j.Stain the gel with 1:10000 SYBR gold in 1x TBE for 15 min. Stain the gel with 1:10000 SYBR gold in 1x TBE for 15 min. k.Excise the band 75–105 nt in length. RT-stop products appear as smearing under the band of fully extended RT products (Figure 1B). Excise the band 75–105 nt in length. RT-stop products appear as smearing under the band of fully extended RT products (Figure 1B). l.Purify the cDNA with the ZR small-RNA PAGE Recovery Kit.Pause point: Store the samples at −20°C up to 4 weeks. Purify the cDNA with the ZR small-RNA PAGE Recovery Kit.Pause point: Store the samples at −20°C up to 4 weeks. Pause point: Store the samples at −20°C up to 4 weeks. 10.Illumina Sequencing Library Preparation.a.Circularize the RT-stop product with ssDNA CircLigase following the manufacturer’s instructions.Note: The amount of RT-stop product could be quantified with qPCR using the RT-stop amplification primer set.b.Recover the DNA by ethanol precipitation (Step 6c) and resuspend in 20 μL of deionized water.c.RT-stop library amplification.i.Prepare the PCR reaction mixture with 10 μl of 2x PCR master mix, 8 μl of circulated RT-product, and 2 μl of 10 μM RT-stop amp primers.ii.Amplify the library; start with the initial denaturation 95°C for 2 min, then cycle 9 to 12 cycles of 98°C for 10 s, 60°C for 45 s, and 72°C for 5 min.iii.Recover the PCR product by ethanol precipitation (Step 6c).d.Perform second size-selection in native TBE polyacrylamide gel.i.Run the PCR product in 8% acrylamide/TBE with a 10 bp DNA size marker and cut off the band in the 78–105 bp length (Figure 1B).ii.Purify the PCR products with the ZR small-RNA PAGE Recovery Kit.Pause point: Samples can be stored at −20°C up to a few weeks.e.Introduce the Illumina sequencing library elements with NEBNext multiplex oligos. Apply 4–5 cycles of PCR reactions following the manufacturer’s instructions.f.Run 8% acrylamide/TBE native DNA gel to quantify the amplified libraries.i.Load 2 μL of PCR mixture to the gel.ii.Visualize the DNA with 1:10000 15 min SYBR gold staining.iii.Determine the concentration by measuring the intensity of the DNA bands in 146–173 bp range.iv.Consolidate equal amounts of 4 libraries in a single tube and perform ethanol precipitation.g.Run the libraries in 8% native acrylamide/TBE gel.h.Stain the gel with 0.5 μg/mL Ethidium Bromide staining for 15 min.i.Excise the band in the 146–173 bp length.j.Purify the PCR products with the ZR small-RNA PAGE Recovery Kit.Pause point: Samples can be stored at −20°C up to a few weeks. Illumina Sequencing Library Preparation.a.Circularize the RT-stop product with ssDNA CircLigase following the manufacturer’s instructions.Note: The amount of RT-stop product could be quantified with qPCR using the RT-stop amplification primer set.b.Recover the DNA by ethanol precipitation (Step 6c) and resuspend in 20 μL of deionized water.c.RT-stop library amplification.i.Prepare the PCR reaction mixture with 10 μl of 2x PCR master mix, 8 μl of circulated RT-product, and 2 μl of 10 μM RT-stop amp primers.ii.Amplify the library; start with the initial denaturation 95°C for 2 min, then cycle 9 to 12 cycles of 98°C for 10 s, 60°C for 45 s, and 72°C for 5 min.iii.Recover the PCR product by ethanol precipitation (Step 6c).d.Perform second size-selection in native TBE polyacrylamide gel.i.Run the PCR product in 8% acrylamide/TBE with a 10 bp DNA size marker and cut off the band in the 78–105 bp length (Figure 1B).ii.Purify the PCR products with the ZR small-RNA PAGE Recovery Kit.Pause point: Samples can be stored at −20°C up to a few weeks.e.Introduce the Illumina sequencing library elements with NEBNext multiplex oligos. Apply 4–5 cycles of PCR reactions following the manufacturer’s instructions.f.Run 8% acrylamide/TBE native DNA gel to quantify the amplified libraries.i.Load 2 μL of PCR mixture to the gel.ii.Visualize the DNA with 1:10000 15 min SYBR gold staining.iii.Determine the concentration by measuring the intensity of the DNA bands in 146–173 bp range.iv.Consolidate equal amounts of 4 libraries in a single tube and perform ethanol precipitation.g.Run the libraries in 8% native acrylamide/TBE gel.h.Stain the gel with 0.5 μg/mL Ethidium Bromide staining for 15 min.i.Excise the band in the 146–173 bp length.j.Purify the PCR products with the ZR small-RNA PAGE Recovery Kit.Pause point: Samples can be stored at −20°C up to a few weeks. a.Circularize the RT-stop product with ssDNA CircLigase following the manufacturer’s instructions.Note: The amount of RT-stop product could be quantified with qPCR using the RT-stop amplification primer set. Circularize the RT-stop product with ssDNA CircLigase following the manufacturer’s instructions.Note: The amount of RT-stop product could be quantified with qPCR using the RT-stop amplification primer set. Note: The amount of RT-stop product could be quantified with qPCR using the RT-stop amplification primer set. b.Recover the DNA by ethanol precipitation (Step 6c) and resuspend in 20 μL of deionized water. Recover the DNA by ethanol precipitation (Step 6c) and resuspend in 20 μL of deionized water. c.RT-stop library amplification.i.Prepare the PCR reaction mixture with 10 μl of 2x PCR master mix, 8 μl of circulated RT-product, and 2 μl of 10 μM RT-stop amp primers.ii.Amplify the library; start with the initial denaturation 95°C for 2 min, then cycle 9 to 12 cycles of 98°C for 10 s, 60°C for 45 s, and 72°C for 5 min.iii.Recover the PCR product by ethanol precipitation (Step 6c). RT-stop library amplification.i.Prepare the PCR reaction mixture with 10 μl of 2x PCR master mix, 8 μl of circulated RT-product, and 2 μl of 10 μM RT-stop amp primers.ii.Amplify the library; start with the initial denaturation 95°C for 2 min, then cycle 9 to 12 cycles of 98°C for 10 s, 60°C for 45 s, and 72°C for 5 min.iii.Recover the PCR product by ethanol precipitation (Step 6c). i.Prepare the PCR reaction mixture with 10 μl of 2x PCR master mix, 8 μl of circulated RT-product, and 2 μl of 10 μM RT-stop amp primers. Prepare the PCR reaction mixture with 10 μl of 2x PCR master mix, 8 μl of circulated RT-product, and 2 μl of 10 μM RT-stop amp primers. ii.Amplify the library; start with the initial denaturation 95°C for 2 min, then cycle 9 to 12 cycles of 98°C for 10 s, 60°C for 45 s, and 72°C for 5 min. Amplify the library; start with the initial denaturation 95°C for 2 min, then cycle 9 to 12 cycles of 98°C for 10 s, 60°C for 45 s, and 72°C for 5 min. iii.Recover the PCR product by ethanol precipitation (Step 6c). Recover the PCR product by ethanol precipitation (Step 6c). d.Perform second size-selection in native TBE polyacrylamide gel.i.Run the PCR product in 8% acrylamide/TBE with a 10 bp DNA size marker and cut off the band in the 78–105 bp length (Figure 1B).ii.Purify the PCR products with the ZR small-RNA PAGE Recovery Kit.Pause point: Samples can be stored at −20°C up to a few weeks. Perform second size-selection in native TBE polyacrylamide gel.i.Run the PCR product in 8% acrylamide/TBE with a 10 bp DNA size marker and cut off the band in the 78–105 bp length (Figure 1B).ii.Purify the PCR products with the ZR small-RNA PAGE Recovery Kit.Pause point: Samples can be stored at −20°C up to a few weeks. i.Run the PCR product in 8% acrylamide/TBE with a 10 bp DNA size marker and cut off the band in the 78–105 bp length (Figure 1B). Run the PCR product in 8% acrylamide/TBE with a 10 bp DNA size marker and cut off the band in the 78–105 bp length (Figure 1B). ii.Purify the PCR products with the ZR small-RNA PAGE Recovery Kit.Pause point: Samples can be stored at −20°C up to a few weeks. Purify the PCR products with the ZR small-RNA PAGE Recovery Kit.Pause point: Samples can be stored at −20°C up to a few weeks. Pause point: Samples can be stored at −20°C up to a few weeks. e.Introduce the Illumina sequencing library elements with NEBNext multiplex oligos. Apply 4–5 cycles of PCR reactions following the manufacturer’s instructions. Introduce the Illumina sequencing library elements with NEBNext multiplex oligos. Apply 4–5 cycles of PCR reactions following the manufacturer’s instructions. f.Run 8% acrylamide/TBE native DNA gel to quantify the amplified libraries.i.Load 2 μL of PCR mixture to the gel.ii.Visualize the DNA with 1:10000 15 min SYBR gold staining.iii.Determine the concentration by measuring the intensity of the DNA bands in 146–173 bp range.iv.Consolidate equal amounts of 4 libraries in a single tube and perform ethanol precipitation. Run 8% acrylamide/TBE native DNA gel to quantify the amplified libraries.i.Load 2 μL of PCR mixture to the gel.ii.Visualize the DNA with 1:10000 15 min SYBR gold staining.iii.Determine the concentration by measuring the intensity of the DNA bands in 146–173 bp range.iv.Consolidate equal amounts of 4 libraries in a single tube and perform ethanol precipitation. i.Load 2 μL of PCR mixture to the gel. Load 2 μL of PCR mixture to the gel. ii.Visualize the DNA with 1:10000 15 min SYBR gold staining. Visualize the DNA with 1:10000 15 min SYBR gold staining. iii.Determine the concentration by measuring the intensity of the DNA bands in 146–173 bp range. Determine the concentration by measuring the intensity of the DNA bands in 146–173 bp range. iv.Consolidate equal amounts of 4 libraries in a single tube and perform ethanol precipitation. Consolidate equal amounts of 4 libraries in a single tube and perform ethanol precipitation. g.Run the libraries in 8% native acrylamide/TBE gel. Run the libraries in 8% native acrylamide/TBE gel. h.Stain the gel with 0.5 μg/mL Ethidium Bromide staining for 15 min. Stain the gel with 0.5 μg/mL Ethidium Bromide staining for 15 min. i.Excise the band in the 146–173 bp length. Excise the band in the 146–173 bp length. j.Purify the PCR products with the ZR small-RNA PAGE Recovery Kit.Pause point: Samples can be stored at −20°C up to a few weeks. Purify the PCR products with the ZR small-RNA PAGE Recovery Kit.Pause point: Samples can be stored at −20°C up to a few weeks. Pause point: Samples can be stored at −20°C up to a few weeks. 11.Deep sequence the resulting library with HiSeq2000/Novaseq/NovaseqX platforms. 110 Gb output generally provides sufficient reads for in-depth transcriptomic analysis. Deep sequence the resulting library with HiSeq2000/Novaseq/NovaseqX platforms. 110 Gb output generally provides sufficient reads for in-depth transcriptomic analysis. Note: Single-end reads higher than 50 bp are sufficient for the analysis. For paired-end sequencing, use the read1 of FASTQ file. RT-stop reads preprocessing Timing: 12 h This step filters out the sequencing reads based on the length of the read and the PCR duplicates using unique molecular barcodes in the randomized region of iSp18 PE Reverse primer.3 12.Trim 3′ Adaptor Sequence. Trim 3′ Adaptor Sequence. > cutadapt -a AGATCGGAAGAGC 13.Remove PCR duplicate. Remove PCR duplicate. > prinseq-lite -derep 1 14.Trim off 6 nucleotide molecular barcode. Trim off 6 nucleotide molecular barcode. > cutadapt -g ˆNNNNNN 15.Limit the resulting sequencing reads 18–45 nt in length. Limit the resulting sequencing reads 18–45 nt in length. > prinseq-lite -max_len 45 -min_len 18 16.Align processed read. Use STAR aligner for rG4Seeker application. Align processed read. Use STAR aligner for rG4Seeker application. > STAR --outFilterMismatchNmax 1 --outSAMattributes NH HI AS nM MD Optional: For RNA duplex structure analysis use bowtie, StructureFold (> bowtie -v 1), and follow the StructureFold manual for downstream application of RNA duplex structures. Here, we continue to address in vivo rG4 structure analysis. Calculating DMS sensitivity of rG4 regions Timing: 12 h rG4Seeker provides a variety of helpful analytic tools for studying rG4.16 This program can predict potential rG4 motifs from the annotated regions of the reference genome and identify empirically detected rG4 sites from K+ dependent RT-stop patterns. We use the program’s output to identify K+ dependent in vitro rG4 regions and to investigate in vivo rG4 folding by quantifying the DMS-resistant RT-stops on these rG4 regions. 17.To obtain K+ dependent rG4 site list, follow the rG4Seeker manual. Provide the reference genome FASTA, gene annotation and aligned bam files of non-DMS treated K+ and Li+ RT-stop libraries. Upon successful execution, the program generates csv file that indicates the genome coordination of significant in vitro rG4 regions. To obtain K+ dependent rG4 site list, follow the rG4Seeker manual. Provide the reference genome FASTA, gene annotation and aligned bam files of non-DMS treated K+ and Li+ RT-stop libraries. Upon successful execution, the program generates csv file that indicates the genome coordination of significant in vitro rG4 regions. rG4_column[0]rG4_column[1]rG4_column[2]rG4_column[3]rG4_column[4]…chrstartendclassstrand…chr147840024784003bulges-…chr11665685116656853two-quartet-…chr13481691134816913longloop-… 18.Perform another rG4Seeker computation using the aligned bam files of DMS-treated K+ and Li+ samples to determine the DMS sensitivity of K+ dependent RT-stop frequency. Perform another rG4Seeker computation using the aligned bam files of DMS-treated K+ and Li+ samples to determine the DMS sensitivity of K+ dependent RT-stop frequency. 19.Download files with “covrss.forward.gz” and “covrss.reverse.gz” extensions. These files contain the numbers of the total reads and RT-stop counts on the genome coordination. Download files with “covrss.forward.gz” and “covrss.reverse.gz” extensions. These files contain the numbers of the total reads and RT-stop counts on the genome coordination. Covrss_ column [0]Covrss_ column [1]Covrss_ column [2]Covrss_ column [3]Covrss_ column[4]Covrss_ column5]chromosomestartendreadsStopsstrandchr14687873468787460-chr14687874468787583-chr14687875468787690-chr146878764687877131- 20.Retrieve RT-stop counting numbers from DMS-treated samples in the rG4-dependent RT-stop regions.a.Remove the nucleotide positions accumulating less than 6 reads from the list.> if int(covrss_ column [3])>= 6 :b.Retrieve the number of reads and stops in the K + -dependent RT-stop sites at rG4 regions. Consolidate reads and stops of each nucleotide position if rG4 RT-stop site comprises multiple nucleotide positions.> if covrss_column[0]== rG4_column[0] and rG4_column[1] <= covrss_column[1] < rG4_column[2] and covrss_column[5] == rG4_column[4]: results_reads[5] = int(results_reads[5]) + int(covrss_column[3]) results_stops[6] = int(results_stops[6]) + int(covrss_column[4]) Retrieve RT-stop counting numbers from DMS-treated samples in the rG4-dependent RT-stop regions.a.Remove the nucleotide positions accumulating less than 6 reads from the list.> if int(covrss_ column [3])>= 6 :b.Retrieve the number of reads and stops in the K + -dependent RT-stop sites at rG4 regions. Consolidate reads and stops of each nucleotide position if rG4 RT-stop site comprises multiple nucleotide positions.> if covrss_column[0]== rG4_column[0] and rG4_column[1] <= covrss_column[1] < rG4_column[2] and covrss_column[5] == rG4_column[4]: results_reads[5] = int(results_reads[5]) + int(covrss_column[3]) results_stops[6] = int(results_stops[6]) + int(covrss_column[4]) a.Remove the nucleotide positions accumulating less than 6 reads from the list.> if int(covrss_ column [3])>= 6 : Remove the nucleotide positions accumulating less than 6 reads from the list.> if int(covrss_ column [3])>= 6 : > if int(covrss_ column [3])>= 6 : b.Retrieve the number of reads and stops in the K + -dependent RT-stop sites at rG4 regions. Consolidate reads and stops of each nucleotide position if rG4 RT-stop site comprises multiple nucleotide positions.> if covrss_column[0]== rG4_column[0] and rG4_column[1] <= covrss_column[1] < rG4_column[2] and covrss_column[5] == rG4_column[4]: results_reads[5] = int(results_reads[5]) + int(covrss_column[3]) results_stops[6] = int(results_stops[6]) + int(covrss_column[4]) Retrieve the number of reads and stops in the K + -dependent RT-stop sites at rG4 regions. Consolidate reads and stops of each nucleotide position if rG4 RT-stop site comprises multiple nucleotide positions.> if covrss_column[0]== rG4_column[0] and rG4_column[1] <= covrss_column[1] < rG4_column[2] and covrss_column[5] == rG4_column[4]: results_reads[5] = int(results_reads[5]) + int(covrss_column[3]) results_stops[6] = int(results_stops[6]) + int(covrss_column[4]) > if covrss_column[0]== rG4_column[0] and rG4_column[1] <= covrss_column[1] < rG4_column[2] and covrss_column[5] == rG4_column[4]: results_reads[5] = int(results_reads[5]) + int(covrss_column[3]) results_stops[6] = int(results_stops[6]) + int(covrss_column[4]) 21.Perform binominal tests to assess the significance of K+ dependent RT-stops in DMS-treated samples. We used BINOM.DIST function of Microsoft Excel, applying a pseudo count of +1 where 0 RT-stops were counted in Li+ samples. Perform binominal tests to assess the significance of K+ dependent RT-stops in DMS-treated samples. We used BINOM.DIST function of Microsoft Excel, applying a pseudo count of +1 where 0 RT-stops were counted in Li+ samples. =BINOM.DIST("K+stops","K+reads",IF("Li+stops"=0,"Li+stops"+1/"Li+reads","Li+stops"/"Li+reads"),FALSE) Expected outcomes A noise-to-signal estimate can be obtained by examining the base composition of the nucleotide triplet upstream of strong RT-stops (Figure 3A). RT-stops in K+ samples tend to occur just upstream of consecutive Guanines. Notably, this G-enrichment is observed under K+ folding but is not under Li+ folding (Figure 3A) — an indication that the procedure likely succeeded. In our previous analysis, we observed 69% Gs in the K+ sample and 33% Gs in the Li+ control. We also note that, relative to non-treated samples, base compositions at the RT-stop in DMS-treated samples occur predominantly at As and Cs, consistent with the sensitivity of As and Cs to DMS modification (Figure 3B). — a further indication of procedural success. Nucleotide composition in K+ and DMS-dependent RT-stop regions (A) Relative nucleotide composition 3 bases upstream of strong RT-stop sites in the presence of K+. Comparison to Li+ treatment is shown. Transcript regions with an RT-stop frequency greater than 0.5 are counted. (B) Relative representation of each base at RT-stop positions in +DMS versus -DMS samples. Numbers of nucleotides in RT-stop libraries are calculated by using rtsc_specificity.py script in StructureFold. Examples of d-rG4-seq outcomes are illustrated in Figure 4. K+-dependent strong RT-stop sites are readily observable at the 3′ ends of rG4 motifs (Figure 4A). These in vitro rG4s are widespread across the transcriptome, including many long non-coding RNAs like Xist, Malat1, and Neat1.6 By providing properly generated K+ and Li+ RT-stop libraries, rG4Seeker identifies thousands of in vitro rG4 sites from non-DMS (in vitro) treated samples. Only a small percentage (1%–3%) of these in vitro rG4 sites show specific occurrences of DMS-resistant in vivo rG4 folding sites. For example, K+ dependent RT-stops are significantly protected from DMS modification at one of the rG4 sites in Ddx17 RNA (Figure 4B, upper panel). However, most K+ dependent RT-stop sites are eliminated following DMS treatment. In the case of unfolded rG4 motifs in Pdrg1, three K+ dependent RT-stop sites are completely lost following DMS treatment (Figure 4B, lower panel). In sum, our d-rG4-seq protocol identifies stably folded in vivo rG4 sites with single-nucleotide resolution. A significant increase in sensitivity achieved through subcellular fractionation allows us to detect low-abundance transcripts, including many long non-coding RNAs. This accurate determination of in vivo RNA structures would be crucial for understanding the complex roles of non-coding RNAs associated with epigenetic processes and disease states. K+ dependent RT-stop profiles (A) Raw RT-stop counts of non-DMS treated samples are plotted across Xist. RNA sequences immediately upstream of the strong RT-stop site are shown. Three K+ dependent RT-stop sites show G-rich motifs upstream (upper panel), while the RT-stop site occurring in both K+ and Li+ samples lack the G skewing (bottom panel). (B) In vitro (DMS-) and in vivo (DMS+) RT-stop frequency profile for the 3′ UTR of Ddx17 and Pdrg1 RNA. RT-stop frequencies are plotted across indicated genes, with potential rG4 sequences shown above, with in vitro RT-stop sites in bolded G. Significant in vivo RT-stops are marked by arrows. Quantification and statistical analysis qPCR analysis was conducted using the CFX96 Touch Real-Time PCR Detection System (Bio-Rad). Native and denaturing acrylamide gel images were visualized with the Amersham Imager 600 (GE Healthcare). RT-stop frequency from the sequencing data was quantified and analyzed using rG4Seeker and StructureFold. Statistical tests of in vitro rG4 sites were performed using a noise-adjusted binomial model of rG4Seeker and the DMS sensitivity of rG4 sites was tested with the BINOM.DIST function of Microsoft Excel. For more in-depth analysis of base-pair RNA structure assays with DMS modification patterns, please refer to the StructureFold manual.15 Limitations d-rG4-seq is a population-based epitranscriptomic assay and may underestimate the number of folded rG4s. Our study showed that >5% of the 5000–6000 in vitro rG4’s are detected in vivo, but we believe that additional rG4’s may fold too transiently to be detected in a bulk RNA-seq analysis. It is possible that many, if not all, of the thousands of rG4 motifs may fold in vivo in select conditions. Bulk RNA-seq data do not capture the dynamic nature of RNA folding and unfolding in living cells. To address these challenges, single-molecule approaches such as smStructure-seq18 may provide a more comprehensive and accurate picture at the structure isoform level. We also note that our rG4-calling method depends on strong RT-Stops in the presence of K+ but not Li+. However, it is known that some robust rG4’s (such as those in TERRA RNA) can fold in the presence of Li+. Thus, the method likely under-calls the total number of rG4’s both in vitro and in vivo. We also draw the reader’s attention to previously published affinity-based rG4 studies using rG4 ligands that demonstrate rG4 formation across a wide range of transcripts.19,20,21,22,23,24 These studies tend to have more limited resolution with peak sizes typically spanning a few hundred nucleotides and may over-call rG4s due to ligand stabilization. Nevertheless, comparing results of d-rG4-seq with those from rG4-ligand affinity-based methods may provide a comprehensive view of all potential rG4-forming sites in vivo. Troubleshooting Problem 1 RNA degradation occurs during the chromatin RNA purification step (Step 5. Extraction of chromatin-bound RNAs). Potential solution If RNA degrades during chromatin RNA purification, it leads to a biased 3′ distribution of sequencing reads. This bias would result in weaker resolving power for the upstream regions of transcripts. Check the RNA integrity by gel electrophoresis or microfluidics-based platforms like TapeStation. RNA degradation may also occur due to improper handling of cultured cells. We commonly observed RNA degradation when frozen cell pellets were thawed before being resuspended in NIB buffer. To prevent this, ensure the remaining part of the pellet remains in contact with dry ice while resuspending the upper part of the pellet. Problem 2 Inefficient adaptor ligation to the fragmented RNA (Step 8. Adaptor Ligation). Potential solution RNA should be highly pure. Use a PAGE gel purification kit with silica columns instead of manual RNA preparation. The high viscosity of PEF8000 can make handling difficult, the reaction solution should be well-mixed by repeated pipetting. Insufficient adenylation of adaptor oligo could cause the ligation issue. 5′ adenylation of adaptor oligo could be monitored with 15% Urea acrylamide gel electrophoresis by +1 nucleotide size shift of the band. Problem 3 Loss of ribonucleic acid content after the denaturing gel purification (Step 10. reverse transcription (RT)-stop library preparation). Potential solution A progressive reduction of nucleic acid material during repeated gel elution can be a major challenge of this process. To mitigate this, always keep the excised gel fragment as small as possible. This can be achieved by limiting the gel electrophoresis run to the minimal time necessary for size separation. Also, make sure the excised gel piece is well fragmented during the gel purification step. Problem 4 Too many PCR duplicates are removed after deduplication (Steps 12–16, RT-stop reads preprocessing). Potential solution This problem is generally associated with the inefficiency of RT-stop library preparation. Low amount of RT-product leads to limited complexity of the PCR templates. A general rule of thumb is to keep the total number of PCR cycles necessary for amplifying the sequencing library in a proper range. The total number of PCR cycles using 630–631 primers and the final Illumina oligos should not exceed 15. Otherwise, a substantial portion of the sequencing reads may derive from PCR duplication. Resource availability Lead contact Any inquiries and requests for the protocol should be sent to the lead contact, Jeannie T. Lee, lee@molbio.mgh.harvard.edu. Technical contact Yong Woo Lee, ylee@molbio.mgh.harvard.edu. Materials availability This protocol did not generate new materials. Data and code availability This protocol did not generate data sets or codes. Data sets for RT-stop profiles can be found in the Xist rG4 study, GSE219083. Acknowledgments We thank all members of the lab for stimulating discussions. This work was funded by a grant from the National Institutes of Health, R01-HD097665, to J.T.L. Author contributions Y.W.L. and J.T.L. conceived the idea of the d-rG4-seq protocol. Y.W.L. designed the d-rG4-seq method. Y.W.L., V.L., and J.T.L. prepared the manuscript and figures. Declaration of interests J.T.L. is a cofounder of Translate Bio and Fulcrum, an advisor to Skyhawk Therapeutics, and a Non-Executive Director of the GSK. References Associated Data Data Availability Statement This protocol did not generate data sets or codes. Data sets for RT-stop profiles can be found in the Xist rG4 study, GSE219083.