Kinematic Analysis of Plasticization and Transportation System of Tri-Screw Dynamic Extruder Authors: Bin Xue, Jun Li, Qu Yang, Guiting Wu, Danxiang Wei, Yijie Ding, Zhenbin Du, Mingshi Huang, Hiroshi Yoshihara Published: 2024 ABSTRACT AbstractWith the growing demand for high-performance polymer composites, conventional single- and twin-screw extruders often fall short of meeting industrial requirements for effective mixing and compounding. This research investigates the kinematic behavior of the plasticization and transport mechanisms in tri-screw extruders when subjected to a vibrational force field. The study specifically examines how applying vibrational force technology can improve the efficiency of polymer mixing. Vibration force field means that in a three-screw mechanism, an axial vibration is applied to the middle screw to produce a vibration force field. Through the development of mathematical and physical models, this study analyzed the motion dynamics of the screw and the influence of a vibrational force field on polymer transport and mixing efficiency. The findings indicate that, in comparison to traditional twin-screw extruders, tri-screw systems can achieve higher shear and elongational rates, leading to enhanced polymer mixing uniformity. Furthermore, applying an axial vibrational force field significantly influenced the shear and elongational strain rates of the material, thereby optimizing its rheological behavior and processing quality. This research not only establishes a theoretical foundation for the design and optimization of tri-screw extruders but also opens new pathways for the efficient processing of high-viscosity composite materials.Keywords: tri-screw extruder, vibration force field, kinematics, shear rate, elongational rate 1. Introduction New materials promote the progress of human society. Since the 20th century, polymer materials have become essential in modern society due to their unique structures, ease of processing, and cost effectiveness [1]. Advances in science, technology, and economic development have expanded their applications across diverse fields, including defense, electronics, healthcare, transportation, and environmental protection [2,3,4,5,6,7,8]. This growing importance has driven increased national focus on both the theoretical and applied research of polymer materials. Extrusion remains the most common processing method for polymers, extensively used in industries such as plastics, rubber, food production, and pharmaceuticals [9,10]. In this process, extruders continuously move the plastic melt from the feed zone to the discharge zone using the rotational motion of screws. The kinematic behavior of screw extruders plays a pivotal role in ensuring the stability of the extrusion process and the quality of the final products. Thus, studying the kinematic principles of screw extruders is vital for enhancing both process stability and product quality. Traditional single-screw extruders are the most widely used extrusion equipment. Studies by Guerrero [11] and Mikulionok [12,13] have examined models of single-screw extruders, focusing on the effects of screw geometry and friction coefficients within the feed zone. Carrot [14] explored the solid conveying and mixing performance of twin-screw extruders. While twin-screw extruders offer enhanced mixing capabilities compared to single-screw systems, they still face challenges like low fill rates and decreased production efficiency, particularly when processing materials such as glass fibers, plant fibers, and biomass [14,15,16,17,18]. In a single-screw extruder, material transport relies on friction between the material, the screw, and the barrel. However, if the material’s viscosity changes or the screw speed fluctuates, conveying can become unstable. For example, low-viscosity materials may experience slippage, leading to inconsistent output. In a twin-screw extruder, the intermeshing of two screws creates a forced conveying effect, which ensures more stable forward movement of the material. This design offers greater adaptability to materials with varying viscosities. Even at high speeds, twin-screw extruders maintain stable conveyance, minimizing issues related to changes in material properties. In recent years, the rising demand for high-performance polymer composites has outpaced the mixing capabilities of conventional single-screw and twin-screw extruders, driving the need for the development of more advanced extrusion equipment. Zhu, Yang [19,20] found through simulation that three screws have better working efficiency and mixing effect than single screws and twin screws. A three-screw extruder introduces an additional screw to the traditional twin-screw design, creating a more complex and diverse flow field. This unique flow structure subjects materials to multidirectional shearing, stretching, and mixing during extrusion. For instance, when producing high-performance blends, the three-screw extruder facilitates finer dispersion and mixing of different polymer phases, resulting in a more uniform microstructure and enhanced material properties—capabilities that are challenging for single- and twin-screw extruders to achieve. Some scholars have also carried out a lot of research in theory [21,22,23,24]. Zhu [25] and Wang [26] studied the flow and mixing mechanism of three-screw extruder by using computational fluid dynamics and Carreau–Bird fluid model. The results showed that the three-screw extruder had better mixing efficiency than the traditional twin-screw extruder. Academician Qu Jinping introduced the vibration force field into single-screw extruders, pioneering a new approach to polymer blending and modification, with notable success. Through visual enhancements to the screw extrusion system, the study explored the impact of the vibration force field on the melting and plasticizing processes during material conveyance. A new extrusion and melting mechanism was developed to explain the effects of this technology [27,28]. Feng [29] and colleagues studied the impact of vibration force fields on the mixing capacity of polymer extruders, developing an analytical model of pulsating total shear strain and analyzing the dynamic laminar mixing process. Their findings showed that the application of vibration increased the total shear strain in the melt within the spiral channel. Specifically, higher vibration frequencies and amplitudes led to greater shear stress experienced by the melt during transport. For example, increasing the vibration frequency from 3 Hz to 7 Hz and the amplitude from 1 mm to 3 mm resulted in a 50% increase in total shear strain. The results demonstrated that introducing a vibration force field enhanced both shear strain and extrusion stability [30,31,32,33]. Under the guidance of advisor Professor He Hezi, in the present research, the vibratory field was applied to a triple-screw extruder, leading to the design and development of a balanced triple-screw dynamic extruder, as depicted in Figure 1. The extruder’s symmetrical screw structure effectively counteracts the axial resistance generated during material plasticization and feeding, reducing the axial dynamic load on the end bearings of the screws. This design also facilitates the generation of large-amplitude axial vibrations in the central main screw. Cai [34] studied the effect of introducing vibration on the mixing of three-screw extruder PP/mEPDM, and the results showed that when the fixed amplitude was 0.5 mm (or the frequency was 15 Hz), the impact strength of the sample increased first and then decreased with the increase of the vibration frequency (or amplitude) when the mEPDM content was 10%, 15%, and 20%. When the frequency was equal to 15 Hz and the amplitude equal to 0.5 mm, the impact strength reached its maximum value. For the sample with mEPDM content of 25%, the impact strength increased approximately linearly with the increase of the vibration frequency and amplitude within the experimental parameters. When the frequency was equal to 20 Hz and the amplitude equal to 0.6 mm, the impact strength reached its maximum value of 54.4 kJ/m2, which was about 9% higher than that without introducing vibration and 18 times that of the pure PP steady-state impact strength. Zhao [35] studied the mixing effect of a vibratory field on EPDM/PP blends, and the results showed that EPDM/PP blends prepared by a three-screw device with a vibratory field (axial vibration frequency of 20 Hz, amplitude of 0.20 mm) had better performance indicators than those prepared by a conventional three-screw device without a vibratory field. Compared with the samples prepared by a twin-screw extruder, the samples prepared by the vibrating three-screw device showed an increase of 22.7% in tensile strength, an increase of 20% in elongation at break, and an increase of 54.2% in tear strength. Three-screw dynamic extruder. In order to study the mixing effects of the vibratory field introduced to this new triple-screw extruder, this paper conducts a dynamic theoretical analysis of the plasticization transport system of the triple-screw dynamic extruder. 2. Screw Physical Model To develop the physical model of the extruder screw, the basic structure of the screw was first analyzed. The extrusion system of the dynamic three-screw extruder features three screws, each with an identical double-headed thread. The cross-sectional profile of each screw, as viewed perpendicular to the screw axis, is illustrated in Figure 2. The whole outline consists of eight arcs: AB, BC, CD, DE, EF, FG, GH, and HA, where the centers of the four arcs AB, CD, EF, and GH are O points. The radii of AB and EF are rb, and the radii of CD and GH are rs. The centers of DE, FG, HA, and BC are at points O1, O2, O3, and O4, respectively, and the radius of each arc is equal to the center distance between adjacent screws. Cross-sectional profile of screw. The plasticizing and transportation system of the balanced three-screw dynamic extruder consists primarily of a barrel and three screws arranged within the barrel’s inner cavity. The spiral threads of all three screws are aligned in the same direction, with the screws initially installed in a lined configuration. The left and right screws are installed with identical phases, offset by 90 degrees relative to the phase of the central screw. The cross-sectional physical model of the plasticizing and transportation system for each screw is shown in Figure 3. The key geometric dimensions of the components within the conveying system are as follows: 1The diameter of the inner hole of the barrel is D and the radius is R; The diameter of the inner hole of the barrel is D and the radius is R; 2The diameter of the cross-section circle of the three screws is d, and the radius is r; The diameter of the cross-section circle of the three screws is d, and the radius is r; 3The center distance of the screw is CL; The center distance of the screw is CL; 4The clearance between the inner wall of the barrel and the screw is a fixed value, δ. The clearance between the inner wall of the barrel and the screw is a fixed value, δ. Establishment of coordinate system of three-screw plasticizing conveying system and marking of main geometric dimensions. Based on the operating principle of the three-screw plasticizing and transportation system, a physical model was developed, with the geometric motion relationship of the system expressed through quantitative formulas. As shown in Figure 3, both rectangular and cylindrical coordinate systems are defined. The rectangular coordinate system (X, Y, Z) is centered at O2, the center of the inner hole of the middle screw. Additionally, three cylindrical coordinate systems, namely (rm1, θ, Z), (rm2, θ, Z), and (rm3, θ, Z), were established with the centers of the inner holes of the three screws, i.e., O1, O2, and O3, serving as their respective origins. The three screws rotate at the same speed, denoted as n, with identical angular velocities. In Figure 3, point O1 represents the center of the inner hole of the left barrel, serving as the origin for the cylindrical coordinate system (rm1, θ, Z). Point O2 is the center of the inner hole of the right barrel and serves as the origin for both the cylindrical coordinate system (rm2, θ, Z) and the rectangular coordinate system (X, Y, Z). 3. Screw Mathematical Model 3.1. Geometric Relationship of Screw The three-screw plasticizing and conveying system consists of three screws arranged in-line, with the middle screw acting as the symmetry axis. The arrangement of the screws on either side is identical, so the geometric relationship can be determined by analyzing the positions of the two outer screws. Consider the left two screws for analysis. First, fix screw A in place. In space, screw B will trace an arc around screw A, with the center-to-center distance, CL, as the radius. By connecting points O1F and O1G and extending this line to the arc, the two limit positions of screw B can be identified, as shown in Figure 4. Geometric relationship of screw size. The points on the four arcs OF BC, DE, FG, and GA are shown in Figure 4. α is the included angle between the two extreme positions OF and OE, introducing angle φ in ΔGO1O, OO1=OG=rs, and O1G=CL (the length of CL is the center distance between two adjacent screws, that is, the length between O1 and O2), from the cosine theorem: For the groove depth of any point M, the length of MN in the Figure 5 is the depth of spiral groove, according to Booy [36,37]. The calculation formula of groove depth is given: Position relationship of M point. The distance from any point on the screw to the rotation center can be obtained from the obtained h(θ): rs=d2. Substituting Equation (2) into Equation (3), we can obtain the following: By extending Equation (4) through Newton’s binomial theorem, we can obtain the calculation equation of rm1: The rm1 is the distance from the center point of the screw to the outer contour of the screw, as shown in Figure 4. Since the diameter of the screw is smaller than the center distance (d