Yb3+-Doped Titanate–Germanate Glasses for Near-IR Luminescence Applications: Synthesis, Characterization, and the Influence of TiO2 Concentration Authors: Karolina Kowalska, Joanna Pisarska, Wojciech A Pisarski, Haohong Chen Published: 2024 ABSTRACT AbstractIn the framework of luminescent rare-earth-doped glasses for near-infrared applications, TiO2-containing inorganic glasses have been recently demonstrated to be a promising alternative to commercially used high-phonon SiO2-based glasses. This study investigates the effect of TiO2 concentration on the near-infrared spectroscopic properties of Yb3+ ions in multicomponent titanate–germanate glasses. A series of glass samples in the xTiO2-(60−x)GeO2-BaO-Ga2O3-Yb2O3 system (x ranging from 0 to 50 mol%) were synthesized using the melt-quenching technique. X-ray diffraction analysis confirmed the fully amorphous nature of the fabricated titanate–germanate samples. Fundamental spectroscopic properties of Yb3+-doped titanate–germanate system consisting of absorption spectra, near-IR emission spectra, and luminescence decay curves have been determined based on measurement using optical spectroscopy. The intensity of the emission band at 1 µm due to the 2F5/2 → 2F7/2 laser transition of Yb3+ ions increases by over 2.3-fold (TiO2 as the network former) compared to a barium gallo-germanate sample without TiO2. Our previous studies indicate that Yb3+-doped titanate–germanate glass is a promising optical material and could be successfully applied to laser technology.Keywords: inorganic glasses, TiO2, lanthanide ions, near-IR luminescence, photonics applications 1. Introduction Glass is one of the most frequently analyzed and most essential materials for understanding structural, thermal, and optical properties. Recently, a lot of interest has been directed towards glasses emitting efficient radiation in the near-infrared range (NIR) [1,2,3,4,5]. In particular, various glass matrices [6,7,8,9,10] activated by rare-earth ions are still tested in order to obtain excellent materials with enhanced luminescent bands and longer lifetimes. In the case of inorganic glasses containing TiO2 (TiO2 < 25%mol), most of the systems possess crystalline phases mainly because of the different titanates, which makes them unsuitable for fiber applications [11,12]. Our TiO2-GeO2-BaO-Ga2O3 host is the first example of a fully amorphous glass with relatively high TiO2 content (up to 50 mol%). It has good thermal stability parameters, required in modern optical fiber technology, and spectacular spectroscopic and laser parameters for the main laser transition of rare-earth ions [13,14,15,16,17]. The key factor to receiving such unique near-infrared luminescence features is a change in the glass network, which leads to a change in the physicochemical properties of the germanate glasses. TiO2 plays the key role as a glass modifier (TiO2 < 30 molar%) or glass former (TiO2 > 30 molar%). It has been experimentally proven that TiO2 participates in forming the glass network with the stretching vibration of Ti-O in the TiO6 unit [18]. On the other hand, our previous measurements of near-IR emission spectra and their luminescence decays clearly indicated that the spectroscopic properties of systems with various GeO2:TiO2 molar ratios strongly depend on the ionic radius of rare-earth ions. Indeed, low (TiO2 < 30 molar%) and high (TiO2 > 30 molar%) concentrations of titanium dioxide favored the near-IR luminescence of rare-earth ions located at the beginning, Pr3+ (1.00 Å) or Nd3+ (0.98 Å), and the end, Er3+ (0.89 Å) or Tm3+ (0.88 Å), of the lanthanide series [19]. All these characteristics indicate that this glass can be used as a material for photonics applications. It is well known that the ionic radius of Ti3+ is equal to 0.67 Å. Notably, the ionic radius of Yb3+ (0.87 Å) is the smallest of the lanthanide series [20] and comparable to the ionic radius of Er3+ and Tm3+ ions. For this reason, an interesting cognitive aspect in a further part of this study will be to analyze the effect of TiO2 concentration on changes in the spectroscopic properties of Yb3+ ions in barium gallo-germanate glass. In general, ytterbium (Yb3+) has been of great interest due to its simple energy level scheme, which is composed of a single optically excited level (2F5/2). Yb3+ is an important luminescent element for various photonics applications such as infrared lasers and amplifiers with wavelengths near 1 µm [21]. In recent years, Yb3+ ions have been successfully incorporated into several glasses [22,23,24,25,26] and crystals [27,28,29,30] to obtain luminescent materials. Concerning the glasses, Koch et al. [31] in 1997 presented an efficient room-temperature Yb:glass laser pumped by a 946 nm Nd:YAG laser with near 48% slope efficiency. In Petrov et al. [32], Yb3+-doped fluoride phosphate glass was pumped by a Ti:sapphire laser based on Kerr-lens mode-locked technology. In 2024, Zhu et al. [33] demonstrated the first diode-pumped wavelength-tunable Yb3+-doped low-silica calcium aluminosilicate (LSCAS) glass lasers. Recently, interesting results were presented by the Petit group [34], which developed an alternative material for the future rare-earth metal shortage. In this case, the novel Yb3+-doped tellurite glasses were prepared using a standard melting process. These authors presented that the precipitation of crystals in low-Yb3+-concentrated glasses in the TeO2–ZnO–Bi2O3 network can be used to increase the intensity of the emission at ∼1 µm of Yb3+ ion emission to the level of highly Yb3+-concentrated glasses. The spectroscopic features of ytterbium ions strictly depend on the chemical composition of the glass. This finding was also clearly confirmed by a study conducted by Zhang et al. [35]. Based on the crystal-field and asymmetry of Yb3+ theories, the Stark splitting of Yb3+ was the highest in germanate glass and the lowest in phosphate glass. To the best of our knowledge, no systematic studies of any luminescence properties of the germanate-based glass host with different TiO2:GeO2 ratios in order to achieve enhancement of the near-IR emission band due to the 2F5/2 → 2F7/2 transition have ever been presented. The selected barium gallo-germanate glass in our study is a good candidate to build an optical device due to its good mechanical properties, high rare-earth solubility, comparatively low phonon energy, and wide emission spectra in the near-IR region. This paper presents Yb3+-doped GeO2–BaO–Ga2O3 and TiO2–GeO2–BaO–Ga2O3 glasses as the optical material in terms of their near-infrared photonic applications. The glasses were synthesized by the melt-quenching technique, followed by an experimental investigation encompassing measurements by X-ray diffraction (XRD), optical absorption, and luminescence spectroscopy. We discuss the effect of the chemical composition of glass on the near-infrared luminescence features of Yb3+ ions, proving the importance of the dual role of titanium dioxide in the glass network. At the end of this study, the role of TiO2 in the materials science field and potential applications of the fabricated Yb3+-doped titanate–germanate glass are discussed below. It was found that the spectroscopic properties of Yb3+-doped barium gallo-germanate glass depends on TiO2 concentration, which confirms the enhanced near-IR emission band at 1 µm due to the 2F5/2 → 2F7/2 laser transition. 2. Materials and Methods 2.1. Yb3+-Doped Titanate–Germanate Glasses: Synthesis A series of low-phonon titanate–germanate glasses emitting radiation in the near-infrared range were prepared using a high-temperature melt-quenching method. This experiment mainly focused on studying the effect of TiO2 content on the optical properties of the barium gallo-germanate (60GeO2-30BaO-9.5Ga2O3-0.5Yb2O3) glass system with the following chemical compositions: xTiO2-(60-x)GeO2-30BaO-9.5Ga2O3-0.5Yb2O3 (where x = 10, 20, 30, 40, 45, and 50), respectively. The concentrations of the components are given in molar %. For better clarity, the chemical compositions of the studied barium gallo-germanate samples with various GeO2:TiO2 molar ratios are shown in Table 1. Table 1Nominal chemical compositions for Yb3+-doped barium gallo-germanate glass samples with various GeO2:TiO2 molar ratios.NoNominal Chemical Composition [mol%]TiO2:GeO2 Molar Ratio160GeO2-30BaO-9.5Ga2O3-0.5Yb2O3without TiO2250GeO2-10TiO2-30BaO-9.5Ga2O3-0.5Yb2O35:1340GeO2-20TiO2-30BaO-9.5Ga2O3-0.5Yb2O32:1430GeO2-30TiO2-30BaO-9.5Ga2O3-0.5Yb2O31:1520GeO2-20TiO2-30BaO-9.5Ga2O3-0.5Yb2O31:2615GeO2-15TiO2-30BaO-9.5Ga2O3-0.5Yb2O31:3710GeO2-50TiO2-30BaO-9.5Ga2O3-0.5Yb2O31:5 Nominal chemical compositions for Yb3+-doped barium gallo-germanate glass samples with various GeO2:TiO2 molar ratios. Samples were prepared under rigorous technological conditions in a special glove-box, in a protective atmosphere of dried argon of high purity. The restrictive procedure of synthesis has also been implemented for rare-earth-doped titanate–germanate glasses [14,15,36], which confirmed the obtained extremely low IR absorption coefficients. High-purity raw materials were GeO2 (99.99%), TiO2 (99.995%, rutile), BaO (99.99%), Ga2O3 (99.99%), and Yb2O3 (99.99%) and they were all purchased from Sigma-Aldrich (St. Louis, MO, USA). The synthesis of titanate–germanate glasses can be summarized by five different steps: (1) the appropriate amounts of all components of 5 g were mixed homogeneously together in an agate mortar, (2) samples were melted in a high-temperature furnace (FCF 4/170 M, produced by Czylok, Poland) at 1250 °C for 0.45 h in corundum crucibles (Łukasiewicz Research Network, Institute of Ceramics and Building Materials, Cracow, Poland), (3) samples were quenched and annealed below the glass transition temperature Tg to eliminate internal mechanical stresses, (4) samples were polished (grinding/polishing machine Struers Labopol-2), and (5) glass samples were prepared for optical measurements. 2.2. Measurements and Characterization The structural characterization of the fabricated samples was provided by X-ray diffraction (XRD) analysis using an X’Pert Pro X-ray diffractometer supplied by PANalytical (Almelo, The Netherlands) with Cu Kα1 radiation (λ = 1.54056 Å). The Cu X-ray tube operating at 40 kW/30 mA was used. Diffraction patterns were measured in step-scan mode with a step size of 0.050 and time per step of 10 s. The absorption and emission properties of the synthesized glass samples were examined using optical spectroscopy. The absorption spectra were recorded using a Varian 5000 UV-VIS-NIR spectrophotometer (Cary 5000, Agilent Technology, Santa Clara, CA, USA). Luminescence spectra and their decays were registered using a VIS/NIR laser system. The laser equipment consisted of a Photon Technology International (PTI) Quanta-Master 40 (QM40) UV/VIS Steady State Spectrofluorometer (Photon Technology International, Birmingham, NJ, USA) coupled with a tunable pulsed optical parametric oscillator (OPO), pumped by the third harmonic of a Nd:YAG laser (Opotek Opolette 355 LD, OPOTEK, Carlsband, CA, USA), a 75 W xenon lamp as an excitation source, a double 200 mm monochromator, a multimode UVVIS PMT R928 detector (PTI Model 914), and a Hamamatsu H10330B-75 detector (Hamamatsu, Bridgewater, NJ, USA). The resolution for spectra measurements was ±0.2 nm. Decays were measured with an accuracy of ±2 µs. In order to compare the emission intensity under the same experimental conditions, measurements of glass systems were carried out at the same slit settings. Analysis of the registered data was carried out using OriginPro 9.1 software. All optical measurements were carried out at room temperature. 3. Results and Discussion Glasses can be prepared in a wide variety of sizes and forms with excellent transparency and homogeneity. In this work, a series of Yb3+-doped titanate–germanate glasses in the form of bulk samples were successfully synthesized and their optical properties were examined in detail in this section. Figure 1 shows the obtained Yb3+-doped glass samples with various GeO2:TiO2 molar ratios (a) and an energy level diagram for Yb3+ ions (b). Photographs of the Yb3+-doped samples after polishing (a) and a simplified energy level diagram of Yb3+ (b). 3.1. Yb3+-Doped Titanate–Germanate Glasses: X-Ray Diffraction Analysis As mentioned in the Section 1, the XRD measurements for glasses containing TiO2 [11,12] revealed that they are partly crystallized. Figure 2 presents X-ray diffraction patterns of the Yb3+-doped titanate–germanate glass samples in the absence and with varying concentrations (from 10 to 50 mol%) of TiO2. The observed diffraction patterns showed the amorphous character of all the samples. Importantly, the diffractograms confirmed the absence of narrow diffraction lines typical of crystalline materials. It suggests the absence of the evolution to a lower degree of the order of the local structure and a relatively broad glass-forming region for the studied compositions. X-ray diffraction patterns of glass without TiO2 and titanate–germanate glasses with various GeO2:TiO2 molar ratios. 3.2. Yb3+-Doped Titanate–Germanate Glasses: Effect of TiO2 on Near-IR Luminescence Properties The study of the absorption spectra reveals the structural and optical features of the glasses that are suitable for various applications. Figure 3a shows the absorption spectra measurements for Yb3+ ions in barium gallo-germanate glasses modified by TiO2. Absorption spectra for Yb3+ ions in titanate–germanate glasses with various GeO2:TiO2 molar ratios compared to GeO2-BaO-Ga2O3 glass (a) and UV cut-off (b). Deconvolution of the absorption spectra for sample without TiO2 (c) and sample containing predominantly TiO2 (50%mol) (d). The absorption spectra of fabricated glasses doped with trivalent ytterbium ions were measured in the UV-visible and near-infrared spectral ranges and show that the chemical composition of the glass host has a significant impact on the absorption edge and intensity. For each glass sample, the absorption spectra exhibit the typical absorption band of Yb3+ ions, which corresponds to the 4f-4f transition of Yb3+ from the ground state (2F7/2) to the excited state (2F5/2). The absorption measurements for Yb3+ ions clearly indicate that the intensity of this band gradually increases with the increase in the TiO2 content. In this study, we used the procedure presented in the work written by Yan et al. [37], which described the deconvoluted absorption spectra for the P2O5-GeO2 glass system in detail. The absorption spectra of Yb3+ in barium gallo-germanate glass and titanate–germanate glass containing 50 mol% TiO2 were deconvoluted by Lorentzian functions. The deconvolution of the Yb3+ ion absorption band showing its Stark splitting is presented in Figure 3c,d. The absorption spectra for selected glass samples are deconvoluted in peaks to resolve the overlapping bands, which originate from the Stark splitting of J manifolds of Yb3+ ions. Similar absorption spectra have been registered previously by Z. Yang et al. [38] for Yb3+ ions in lead–germanate (10Na2O–60GeO2–30PbO) systems and indicated that for glasses, due to the low symmetry at Yb3+ sites, a clearly resolved band at 976 nm is observed. Similar results were also described by M. Seshardi et al. [39], who conducted a detailed optical study of Yb3+-doped borophosphate glasses for IR laser application. Another pointed out that the important issue is the local environment around Yb3+. It should be noted that the position of the first deconvoluted peak at 904 nm (sample without TiO2) shifts to a longer wavelength (red shift) in the comparison in Figure 3d (sample with 50mol% TiO2). A similar effect was observed by Wang et al. [40] in highly Yb-doped silica glass containing various amounts of fluorine doping. Moreover, the effect of TiO2 on the optical properties of fabricated Yb3+-doped glasses is evidently confirmed by the UV cut-off wavelength. The UV cut-off wavelength, defined as the intersection between the zero baseline and the extrapolation of the absorption edge, was determined. For the sample without TiO2, the absorption edge is observed at 295 nm. The UV cut-off (Figure 3b) for titanate–germanate glass is shifted to longer wavelengths with increasing TiO2 concentration (389 nm for glass with molar ratio GeO2:TiO2 = 1:5). These changes can be explained by the modification with the ligand field around Yb3+ ions by the incorporation of TiO2, which is fully consistent with our previous spectroscopic results for rare-earth-doped titanate–germanate glasses [14,15,16,17,19] and undoped glass hosts [18] for near-infrared luminescence applications. Figure 4a presents the near-IR emission spectra (λexc = 980 nm) of Yb3+ ions in multicomponent titanate–germanate glasses. The spectra are compared with the sample without TiO2. Near-IR luminescence spectra of Yb3+ ions in fabricated glass samples (a) and emission intensity for the main 2F5/2 → 2F7/2 laser transition and emission bandwidth (b) as a function of TiO2 content. The registered near-IR emission band is related to the main 2F5/2 → 2F7/2 laser transition of Yb3+. It is clearly seen that the emission spectrum for the Yb3+-doped barium gallo-germanate glass sample consists of three emission peaks centered at 980 nm, 1030 nm, and 1070 nm. In general, spectroscopic studies indicate that the intensity of the luminescence band of Yb3+ ions is enhanced with increasing titanium dioxide concentration in the GeO2-BaO-Ga2O3 system. Notably, the strongest emission peak is located at 1030 nm, and the intensity begins to increase (2.3-fold increase) when the TiO2 concentration is beyond 30 mol% (Figure 4b). On the other hand, the intensity of the emission peak located at about 1070 nm decreases with the increase in TiO2 content, and for systems where TiO2 acts as a network-former component (TiO2 > 30 molar%), it is poorly detectable. In this section, a spectroscopic parameter, such as the full width at half maximum, was estimated for the synthesized glasses, similar to previous work on Yb3+ ions in inorganic glasses [24,35,41,42] and other lanthanides [36,43,44,45,46,47,48]. In general, the luminescence bandwidth, referring to the FWHM for the main 2F5/2 → 2F7/2 laser transition at 1030 nm of Yb3+, is nearly independent on TiO2 concentration, and its value is close to 83 nm (Figure 4b). The results of calculating the full width at half maximum for the main 2F5/2 → 2F7/2 laser transition of Yb3+ ions using the Gaussian function in OriginPro software are presented in Figure 5. A fitting procedure was also used in the study presented by the research group of Boulon et al. for Yb3+-doped lead silicate glasses [49], Yb3+-doped silica fibers [50], and also for Yb3+ ions in tellurite glass [51] or Yb3+ ions in lead phosphate glasses [52]. Determination of the FWHM parameter for selected glass samples without TiO2 (a), and with molar ratio GeO2:TiO2 = 1:1 (b) and 1:5 (c) using Gaussian function. The observed optical emission spectra of Yb3+ ions in the titanate–germanate glass is very similar to the corresponding Yb3+ optical spectra observed in lead fluoroborate glass [53], and completely different than Yb3+-doped glass-ceramics [54] or ytterbium(III) complexes [55,56]. N. Purnachand [57] and co-workers analyzed the properties of Yb3+-doped lead antimony borate glass belonging to the high-phonon glass family and registered the emission spectra of the studied samples. It was observed that the PbO–Sb2O3–B2O3 system exhibited a stronger emission band at about 978 than at 1014 nm due to the 2F5/2 → 2F7/2 transition. Similar results were also described by D. Rajeswara Rao et al. [58], who conducted a detailed optical study of Yb3+ ions in a PbO–PbF2–B2O3 glass system. Studies of glasses doped with Yb3+ ions indicated these systems could emit a near-IR luminescence band as a result, and its intensity strongly depends on the glass host, chemical composition, network-former oxide, network-modifier oxide, and/or Yb3+ ion concentration. Moreover, the enhanced and broad emission spectrum obtained for multicomponent glass with Yb3+ ions with a molar ratio of GeO2:TiO2 = 1:5 (50 mol% TiO2) shows its promise as an attractive medium operating over a wide range of NIR wavelengths (1–1.2 μm). For further investigation, luminescence decays from the 2F5/2 state of Yb3+ ions have been analyzed in detail. The decay curves for the 2F5/2 (Yb3+) state in multicomponent titanate–germanate glasses were measured under excitation at 980 nm and while monitoring the emission wavelength at 1030 nm. The luminescence decay curves for Yb3+ are presented in Figure 6. The obtained results clearly demonstrated that decays are reduced with increasing TiO2 concentration in the glass composition. Based on decay curve measurements, luminescence lifetimes for the 2F5/2 state of the Yb3+ ion level were evaluated from a nearly single exponential fit. The measured lifetimes for the 2F5/2 state of Yb3+ varying with TiO2 concentration are schematically shown in Figure 6b. Luminescence decay curves of the 2F5/2 state for the investigated glass samples doped with Yb3+ ions with various GeO2:TiO2 molar ratios (a) and luminescence lifetimes (b). The longest lifetime measured here is 1.38 ms for the Yb3+-doped barium gallo-germanate glass, which is longer than that reported for the Yb3+-doped Ga2O3-GeO2-BaO-K2O system (0.95 ms) [59]. It is observed that the 2F5/2 excited state decreases from 1.21 ms to 0.80 ms in the investigated glasses when TiO2 concentration increases from 10% to 50 mol%. This decrease was related to the concentration quenching effect. Concentration quenching has been analyzed for different optical matrices containing Yb3+ ions. This phenomenon was also described by P. Yang et al. [60], who conducted a detailed optical study of Yb:YAG crystals with a high Yb3+ doping level. Kummara et al. [61] determined the luminescence lifetime for Yb3+-doped oxyfluoride glasses, ranging from 1.52 to 0.18 ms, and showed that the quenching of luminescence lifetime could be due to multiphoton relaxation, direct coupling with OH− groups, or energy transfer among Yb3+ ions. In the present study, the Yb3+-doped glass samples were prepared under rigorous technological conditions in glove-box, in a protective atmosphere of dried argon of high purity. Additionally, in our previous work for active oxide [62] and oxyfluoride [63] titanate–germanate glasses for near- and mid-IR luminescence applications, extremely low-IR absorption coefficients were achieved. Consequently, it is assumed that the concentration quenching effect connected with the dominant mechanisms of lifetime quenching is multiphoton relaxation as well as energy transfer among the Yb3+ ions. The luminescence decay measurements of fabricated glasses for photonic applications confirmed that the analysis of the influence of the GeO2:TiO2 ratio on spectroscopic parameters of Yb3+ ions is crucial in the presented preliminary study. The luminescence lifetime for the excitation state transition is compared to several Yb3+-doped luminescent materials published previously. The results are summarized in Table 2. Table 2Comparative analysis of luminescence lifetimes in different luminescent materials (glasses, crystals, glass-ceramics) doped with Yb3+ ions emitting in the near-infrared range.Luminescent MaterialLuminescenceLifetime [ms]ReferenceGeO2-BaO-Ga2O3-0.5%Yb2O31.38this workTiO2-GeO2-BaO-Ga2O3-0.5%Yb2O3 (TiO2:GeO2 = 1:5)1.21this workTiO2-GeO2-BaO-Ga2O3-0.5%Yb2O3 (TiO2:GeO2 = 1:1)1.02this workTiO2-GeO2-BaO-Ga2O3-0.5%Yb2O3 (TiO2:GeO2 = 5:1)0.80this workGa2O3-GeO2-BaO-K2O:0.5%Yb2O30.97 [59]Li2B4O7:0.4%Yb0.48[64]MgF2-BaF2-Al(PO3)3-Ba(PO3)2:1%Yb2O30.65[65]Na(PO3)3-Al(PO3)3:1%Yb2O30.90[66]Al2O3-SiO2:0.3%Yb2O30.92[67]P2O5-K2O-MgO-Al2O3-0.5%Yb2O30.96[68] GeO2-PbO-Ga2O3-Na2O:1.5%Yb2O31.76[69]NaPO3-Na2O-NaF-1.25%Yb2O31.8[70]ZrO2-1%Yb3+:Y2O31.85[71] P2O5-ZnO-Al2O3-BaO-PbO-1.0%Yb2O31.45 [72]CaF2:1%Yb3+2.88[73]P2O5-B2O3-Li2O-ZnO:0.5%Yb2O31.73[74]Bi2O3-B2O3:2%Yb2O30.34[75] Comparative analysis of luminescence lifetimes in different luminescent materials (glasses, crystals, glass-ceramics) doped with Yb3+ ions emitting in the near-infrared range. In general, TiO2 is making a great contribution to the field of engineering materials thanks to its unique properties [76,77,78,79,80]. In 2019, X. Kang et al. [81] presented an excellent review highlighting the role of TiO2 in engineering and applications. Encouragingly, the glass system containing TiO2 is dedicated to acting as an active optical center for rare-earth ions. Importantly, titanium plays a dual role in the glass structure: as the network former or as the network modifier. TiO2, a member of 3D transition metal oxides, is considered a valuable glass constituent in some special glasses. Notably, the Judd–Ofelt analysis for Nd3+, Er3+, Pr3+, Tm3+, and Ho3+ presented in our previous works [14,15,17,19] clearly indicated that TiO2 content modifies the degree of covalency of the rare-earth ligand field and fabricated glass systems exhibited more rigidity. A similar relationship between the incorporation of TiO2 and GeO2 and the properties of telluride glasses was described by Tang et al. [82]. Although the perspectives of germanate-based glasses for photonic applications are very motivating, obtaining glasses with an amorphous nature and enhanced near-infrared luminescence properties is not trivial. Finally, the research in this paper perfectly demonstrates that the use of the TiO2 component in a Yb3+-doped barium gallo-germanate glass system, which plays a dual role in the glass structure depending on its concentration but presents unique luminescence properties in the near-infrared range, may be an attractive way of designing new optical materials for laser technology. Our preliminary results presented in this paper are in keeping with current standards and also have important implications for the future of photonic glasses. Several spectroscopic and near-infrared (NIR) laser parameters for Yb3+ based on theoretical calculations will be discussed in another paper in detail. Certainly, the influence of TiO2 concentration on the spectroscopic properties of Yb3+ ions needs further study. 4. Conclusions Novel Yb3+-doped low-phonon titanate–germanate glasses were developed to understand the impact of TiO2 addition on the optical near-infrared luminescence properties. In this study, the preliminary experimental results for Yb3+ have been discussed for samples without TiO2 and for samples where the GeO2:TiO2 molar ratio was changed from 5:1 (50 mol% GeO2; 10mol% TiO2) to 1:5 (10 mol% GeO2; 50mol% TiO2). We have encountered interesting results that point to the application of TiO2-GeO2-BaO-Ga2O3-Yb2O3 glass for near-infrared photonic applications. The samples where GeO2 was substituted by TiO2 were examined using X-ray diffraction (XRD), absorption, and luminescence spectroscopies. Based on data analysis, we have shown the following conclusions: X-ray diffraction analysis revealed that all received samples are fully amorphous. The absorption edge for Yb3+-doped titanate–germanate glass was shifted to longer wavelengths (red shift) with increasing TiO2 concentration. The absorption measurements for Yb3+ ions clearly indicated that the intensity of the absorption band corresponding to the transition originating from the 2F7/2 ground state to the 2F5/2 higher-lying state is the most intense for samples when TiO2 plays the role as glass network former. X-ray diffraction analysis revealed that all received samples are fully amorphous. The absorption edge for Yb3+-doped titanate–germanate glass was shifted to longer wavelengths (red shift) with increasing TiO2 concentration. The absorption measurements for Yb3+ ions clearly indicated that the intensity of the absorption band corresponding to the transition originating from the 2F7/2 ground state to the 2F5/2 higher-lying state is the most intense for samples when TiO2 plays the role as glass network former. Near-IR emission spectra and their decays were analyzed in detail. Adding titanium dioxide into Yb3+-doped TiO2-GeO2-BaO-Ga2O3 glass significantly influenced the 1 μm luminescent properties. For titanate–germanate glass containing 50%mol TiO2, the integrated emission intensity for the main 2F5/2 → 2F7/2 laser transition of Yb3+ was enhanced more significantly (2.3-fold increase) compared to the sample without TiO2. Luminescence decays from the 2F5/2 state of Yb3+ ions were measured. The 2F5/2 measured lifetimes depend critically on titanium dioxide concentration. Near-IR emission spectra and their decays were analyzed in detail. Adding titanium dioxide into Yb3+-doped TiO2-GeO2-BaO-Ga2O3 glass significantly influenced the 1 μm luminescent properties. For titanate–germanate glass containing 50%mol TiO2, the integrated emission intensity for the main 2F5/2 → 2F7/2 laser transition of Yb3+ was enhanced more significantly (2.3-fold increase) compared to the sample without TiO2. Luminescence decays from the 2F5/2 state of Yb3+ ions were measured. The 2F5/2 measured lifetimes depend critically on titanium dioxide concentration. From an application point of view, this titanate–germanate glass, when TiO2 plays the role of a glass network former, can be a promising starting material for solid-state lasers. The development of efficient new Yb3+-doped titanate–germanate glass will continue to be a research priority for our group in the near future. Acknowledgments The authors thank Tomasz Goryczka (Institute of Materials Engineering, University of Silesia) for the support with the XRD measurements. Author Contributions Conceptualization, K.K., J.P. and W.A.P.; methodology, K.K.; software, K.K.; validation, K.K.; formal analysis, K.K. and W.A.P.; investigation, K.K.; data curation, K.K.; writing—original draft preparation, K.K.; writing—review and editing, J.P. and W.A.P.; visualization, K.K.; supervision, W.A.P.; project administration, W.A.P.; funding acquisition, W.A.P. All authors have read and agreed to the published version of the manuscript. Institutional Review Board Statement Not applicable. Informed Consent Statement Not applicable. Data Availability Statement The original contributions presented in this study are included in the article. Further inquiries can be directed to the corresponding authors. Conflicts of Interest The authors declare no conflicts of interest. Funding Statement The research activities are co-financed by the funds granted under the Research Excellence Initiative of the University of Silesia in Katowice. Footnotes Disclaimer/Publisher’s Note: The statements, opinions and data contained in all publications are solely those of the individual author(s) and contributor(s) and not of MDPI and/or the editor(s). MDPI and/or the editor(s) disclaim responsibility for any injury to people or property resulting from any ideas, methods, instructions or products referred to in the content. References Associated Data Data Availability Statement The original contributions presented in this study are included in the article. Further inquiries can be directed to the corresponding authors.