Experimental study on the dust control performance of rotating fog curtain under the perturbation of long-pressure and short-pumping ventilation Authors: Jingxu Chen, Yongkai Zhi Published: 2024 ABSTRACT The dust source point in the coal-breaking operation prolonged activities generate substantial dust, diminished the air quality at the tunneling face. This study focuses on the pneumatic vortex fog curtain dust control system in the underground coal mine tunneling face. It explores the dust-trapping performance of this system under the disturbance of a long-pressure and short-suction auxiliary ventilation system. The results indicate that the respiratory dust captured by the fog curtain wall on the driver’s working side can be reduced from an average concentration of 135.5 mg/m3 to 2.5 mg/m3, and on the 15 m downwind side of the coal-cutting machine, it decreases from 70.2 mg/m3 to 2.5 mg/m3. Under the disturbance of the long-pressure and short-suction ventilation system, as the wind speed increases, the rotating fog curtain gap expands, reducing the sealing performance. Without compromising the fog curtain conditions, this combined system achieves efficient dust suppression, significantly improving the working environment at the tunneling face. Introduction When modern mining roadheaders perform high-efficiency coal cutting operations, the large amount of dust generated by the cutter teeth cutting and crushing coal accounts for more than 80% of the entire working face, causing severe dust pollution at the working face1–3. After dust is generated at the dust source point, it is entrained by the airflow and transported along the direction of the wind flow due to the smooth airflow within the site. Additionally, the dusty airflow is slowly discharged along the return air side of the roadway, spreading throughout the entire roadway4–6. The use of traditional ventilation dust removal and atomized dust removal methods individually both have certain drawbacks, and their effectiveness in capturing suspended respirable dust is not significant7–9. Therefore, based on the dust generation characteristics of the coal mining system at the tunneling face, the use of a pneumatic spiral spray dedusting system to form a rotating fog curtain in conjunction with an auxiliary ventilation system can control the dust concentration at the tunneling face. This method effectively intercepts dust pollution at the coal cutting dust source point, forming an effective occupational hazard prevention and control method. There has been extensive research on the use of traditional air curtains and spray dust suppression to control particulate matter concentration. Li et al. developed air curtain dust collection technology, and their research results indicated that this method can effectively control unorganized dust during the real-time operation of material dropping10. Cai et al. developed an air curtain dust prevention technology for fully mechanized mining working faces, forming a triangular air curtain between the coal cutter and the walkway. After applying this technology for dust suppression at the fully mechanized working face, it effectively prevented dust from entering the operator’s work area11. Mo et al. proposed on-board dust removal technology for coal cutters and verified the performance of the on-board air curtain dust remover through practical field tests12. Yang et al. proposed a modular diversion airflow system and dust control technology for roadheaders, studying and analyzing the influence of different side outlet airflow diversions, tilt angles, and radial-axial air volume ratios, and obtained the influence rules of air and dust coupling diffusion13. Jahanzaib et al. conducted monitoring research on air curtains from the perspective of slipstream motion, maximizing the reduction of particulate matter concentration14. Additionally, many studies have considered the impact of forced ventilation conditions within roadways on the performance of air curtain dust control15,16. Another important spray dust suppression technology has been developed by Jing et al., who based on the air-water spray principle and vortex airflow laws, developed a new type of ultra-fine spiral atomizing nozzle. They determined the optimal spiral effect parameters and verified through field experiments that this device improved dust suppression effectiveness17,18. Peng et al. developed a new type of shearer sprayer specifically for the drum cutting process, demonstrating that this device better achieved dust control rates19. Han et al. studied the impact of forced ventilation on the diffusion patterns of droplets sprayed by external sprayers on roadheaders. They proved that using a Venturi Duct with Coanda Effect (VDCE) effectively alleviated airflow interference on droplet distribution, and VDCE improved the suppression efficiency of respirable dust20. Fang et al. researched respirable coal dust based on the atomization of gas-liquid two-phase flow nozzles, obtaining insights into the effect of humidity and demonstrating good dust suppression performance21.Xie et al. put forward the “plugging” method of fully mechanized mining face to study the effect of negative pressure dust removal after the formation of ventilation resistance in roadway. Yang Xianhang et al. put forward a modular dust suppression method by diverting ventilation and dust control, and studied the law of air-dust coupling diffusion movement under different conditions. Many other studies have also combined the atomization performance in the existing forced ventilation environment of roadways22,23,and a CFD-DEM coupling simulation method based on k-ε two-path turbulence model and Hertz-Mindlin model. These studies provide valuable references for the early research of rotating fog curtains, with most researchers considering the impact of forced ventilation disturbances on dust control equipment. Therefore, in this study, we further investigate the dust control capability of this device under forced ventilation conditions. This study primarily focuses on the dust control performance of the pneumatic spiral spray dedusting system under long-pressure and short-pumping ventilation disturbances. Therefore, a numerical simulation is employed to analyze the breakup of droplets under fluid flow conditions and the trajectory of droplet movement under long-pressure and short-pumping ventilation conditions. This analysis aims to determine the system’s resistance to disturbances. Additionally, we validate and refine the numerical simulation results by combining the simulated fluid dynamics with the constructed experimental platform, simulating the comprehensive dust control system for the tunneling face under long-pressure and short-pumping ventilation disturbances. This process confirms the effectiveness of the pneumatic spiral spray dedusting system’s dust control performance under long-pressure and short-pumping ventilation disturbances. Pneumatic spiral spray dedusting device working principle In order to address the issue of dust pollution in the tunneling face, a pneumatic spiral spray dedusting technology is proposed. As illustrated in Fig. 1, the device mainly comprises an air inlet pipe, water pipe, annular air duct, annular water pipe, high-pressure air jet injector, and nozzles. The technology installs the air inlet pipe, the water pipe is connected with the replacement water pipe, and the high-pressure air flow ejector is uniformly arranged along the inner ring of the annular air duct to improve the droplets and air flow speed at the nozzle, and the longitudinal ring wind field is formed through the annular air duct. The external water spray is impacted by the rotating jet flow, forcibly altering the motion direction of water droplets in the spray field. The droplets moving forward gain tangential kinetic energy, forming a dense, rotating, and directed mist wall towards the working face. A conceptual 3D representation of the pneumatic spiral spray dedusting device is illustrated in Fig. 2, where R represents the atomization radius of the equipment. Fig. 1Schematic diagram of device structure installation. 1- air inlet pipe, 2- water pipe, 3- annular air duct, 4- annular water pipe, 5- high-pressure air jet injector, 6- nozzles. Schematic diagram of device structure installation. 1- air inlet pipe, 2- water pipe, 3- annular air duct, 4- annular water pipe, 5- high-pressure air jet injector, 6- nozzles. Fig. 2A conceptual 3D representation of the pneumatic spiral spray dedusting device. A conceptual 3D representation of the pneumatic spiral spray dedusting device. Compared to traditional spray dust suppression methods, the formed dense mesh-like mist curtain wall can better seal the tunnel’s cross-section, effectively isolating dust’s diffusion and movement. Based on the preliminary experimental results analysis, first, the dust-laden airflow in the tunnel is forced to collide with the mist curtain wall; second, dust particles collide with mist droplets, condense, and rapidly settle. However, most tunnels have long-pressure and short-pumping forced ventilation systems in production processes. Therefore, we believe this system may have a certain impact on implementing this technology. Numerical simulation for analog simulation Physical modeling Figure 3 displays the physical model of the tunneling face. A coordinated system was established, including the tunnel structure, EBZ160A tunneling machine, pneumatic spiral spray dedusting system, long-pressure and short-pumping ventilation system, and conveyor belt system. Fig. 3Illustrates the physical model of the comprehensive pneumatic spiral spray dedusting system. Illustrates the physical model of the comprehensive pneumatic spiral spray dedusting system. Mathematical modeling The system operated under standard room temperature and atmospheric pressure conditions without energy conversion. Within the computational domain, air was the medium, and the fluid was treated as an incompressible gas. Computational Fluid Dynamics (CFD) software was employed for analysis and calculations. Particle phase linear double equations k-ε turbulence model The k-ε turbulence model can effectively describe the interaction of particle phase and gas phase, and shows good applicability in gas-solid two-phase flow with high particle concentration. Moreover, it is universal to turbulence simulation in most engineering, and can be applied to a variety of complex environments from fluid to particles, and can better simulate the diffusion and migration behavior of particles in high turbulent region. Especially in high turbulence intensity environments such as mine airflow disturbance and dust control, it shows high accuracy. Therefore, k-ε turbulence model is chosen for mathematical model construction. A certain physical quantity of the particle phase was decomposed into three parts to obtain the continuous equation, momentum equation, and dual-scale turbulence model equations for the particle phase24–26, as follows: Turbulent kinetic energy equation (k equation):1\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\frac{{\partial \left( {\rho k} \right)}}{{\partial t}}+\frac{{\partial \left( {\rho k{u_i}} \right)}}{{\partial {x_i}}}=\frac{\partial }{{\partial {x_i}}}\left[ {\left( {\mu +\frac{{{\mu _i}}}{{{\sigma _k}}}} \right)\frac{{\partial \left( k \right)}}{{\partial {x_j}}}} \right]+{G_k} - \rho \varepsilon$$\end{document} Turbulent dissipation rate equation (ε):2\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\frac{{\partial \left( {\rho \varepsilon } \right)}}{{\partial t}}+\frac{{\partial \left( {\rho \varepsilon {u_i}} \right)}}{{\partial {x_i}}}=\frac{\partial }{{\partial {x_i}}}\left[ {\left( {\mu +\frac{{{\mu _i}}}{{{\sigma _\varepsilon }}}} \right)\frac{{\partial \left( \varepsilon \right)}}{{\partial {x_j}}}} \right]+\rho {C_1}E\varepsilon - \rho {C_2}\frac{{{\varepsilon ^2}}}{{k+\sqrt {v\varepsilon } }}$$\end{document} Where: C1 = max [0.43, η/(η + 5)], η = Ek/ε; C2 is a constant; \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$E={\sqrt {2{E_{ij}}E} _{ij}}$$\end{document}; Gk turbulence kinetic energy generation, Gk = µgE2; σk, σε are the coefficients of turbulence Prandtl coefficients in the flow field for the k and ε equations, and the empirical values of C2 are taken to be 1.9 for the calculations, with σk = 1.0, σε = 1.2. Turbulent viscosity, µt, can be expressed as a function of k and ε:3\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\mu _t}=\rho {C_\mu }\frac{{{k^2}}}{\varepsilon }$$\end{document} Where Cµ is a function related to the mean rate of change of stress and the turbulent flow fields k and ε, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$C_{\mu } = 1/\left( {A_{0} + A_{s} U^{*} k/\varepsilon } \right)$$\end{document}, where A0 = 4.0; \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${A_S}=\sqrt {6\cos \varphi }$$\end{document}; \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\varphi = \frac{1}{3}\arccos \left( {\sqrt {6W} } \right)$$\end{document}; \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$W=\frac{{{E_{ij}}{E_{jk}}{E_{kj}}}}{{{{\left( {{E_{ij}}{E_{ij}}} \right)}^{0.5}}}}$$\end{document}; \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${E_{ij}}=0.5\left( {\frac{{\partial {u_i}}}{{\partial {x_i}}}+\frac{{\partial {u_j}}}{{\partial {x_j}}}} \right)$$\end{document}; \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${U^*}=\sqrt {{E_{ij}}{E_{ij}}+{{\tilde {\Omega }}_{ij}}{{\tilde {\Omega }}_{ij}}}$$\end{document}; \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\Omega _{ij}}={\tilde {\Omega }_{ij}} - {\varepsilon _{ij\kappa }}{\omega _k}$$\end{document}; \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\tilde {\Omega }_{ij}}={\Omega _{ij}} - 2{\varepsilon _{ij\kappa }}{\omega _\kappa }$$\end{document}, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\tilde {\Omega }_{ij}}$$\end{document} is the time-averaged rotation rate tensor with angular velocity \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\omega _\kappa }$$\end{document}; \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\tilde {\Omega }_{ij}}$$\end{document} is the similar value of \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\Omega _{ij}}$$\end{document}; W is power(W); U* is internal energy (J). Interphase drag force model A significant amount of analysis has been conducted on the interphase drag force model between gas and solid phases in COMSOL. During the calculations, this work adopted the commonly used drag force model, the Schiller-Naumann model. Mainly due to its high applicability in a wide range of applications in gas-solid two-phase fluids, the drag force function of Schiller-Naumann model can provide more accurate results in the calculation of drag forces at gas-solid interface, so it is widely used in fluid calculation, and has a good balance effect on model stability and computational efficiency.The drag force experienced by the particles is given by27,28:4\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${F_d}=\frac{1}{{{\tau _p}}}{m_p}\left( {{U_g} - {U_p}} \right)$$\end{document}5\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\tau _p}=\frac{{4{\rho _p}{d_p}^{2}}}{{3\mu {C_D}{{\operatorname{Re} }_r}}}$$\end{document} where Cd is the drag force function experienced by the particles:6\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${C_d}=\frac{{24}}{{{{\operatorname{Re} }_r}}}(1+0.15\operatorname{Re} _{r}^{{0.687}})$$\end{document} and Rep is the particle Reynolds function:7\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${\operatorname{Re} _p}=\frac{{\rho \left| {{U_g} - {U_p}} \right|{d_p}}}{\mu }$$\end{document} Results and discussion To investigate the impact of air pressure systems on the migration and diffusion of rotating fog curtains in a driving face, we simulate and analyze the formation effectiveness of these dust control curtains under pressured ventilation conditions based on the configuration of the aforementioned dust control system. Initially, a physical model with a full-scale model was established using CFD numerical simulation techniques. To optimize computational efficiency, simplifications were made to the models representing the driving lane, driving machine and air duct. The physical model of the driving face is illustrated in Fig. 4 below. The mesh quality map is illustrated in Fig. 5 below. The wind speed map obtained by grid division is illustrated in Fig. 6 below. Fig. 4Mesh generation for the working face of long-pressure and short-pumping ventilation. Mesh generation for the working face of long-pressure and short-pumping ventilation. Fig. 5Mesh quality map. Mesh quality map. Fig. 6Different meshing the wind speed. Different meshing the wind speed. In the COMSOL simulation software, the simplified models of tunnels, tunnel machines, and air pipes are discretized into grids for numerical simulation analysis, This is achieved by constructing a network simulation diagram that represents the physical model of the tunnel. Grid independence is validated through a comparison of calculation results across varying mesh densities; if results remain stable with mesh refinement, the simulation can be deemed grid-independent. By analyzing wind velocity and dust movement in the driving section of the lane using three different grid division schemes coarse, very coarse, and fine it was found that there were no significant structural differences among these divisions. Thus, it can be concluded that the grid division satisfies numerical simulation requirements, Notably, when examining values beyond 2.6 m on the X-axis, some discrepancies in wind speed emerge between the three grid divisions. The overall trend indicates uniform changes in wind speed during simulations; therefore, refined lines were selected for further numerical analysis. A total of 1966,518 mesh units were used in the simulation. Compared with coarse mesh division and very coarse mesh division, refined mesh division has smoother result curve, and the simulation results are more close to the actual situation. The component mass distribution illustrated in the quality diagram falls within a range of 0.5 to 1, thereby confirming its reliability. Furthermore, both experimental validation and correctness assessments reinforce confidence in the adequacy of grid division. Simulation results of the airflow field under the disturbance conditions of long-pressure and short-pumping ventilation Using the k-ε turbulence model, calculations were performed on the rotating jet velocity field. The velocity distribution and integrity of the rotating wind curtain were obtained by analyzing the meteorological flow field and jet movement paths under different long-pressure and short-pumping ventilation conditions. This strategy aimed to analyze the formation effectiveness of the wind curtain using the long-pressure and short-pumping integrated dust control system. Note that the pressure airflow duct exit was set as the axial inlet, while the suction airflow duct served as the outlet. A pressure-to-suction ratio of 1.5 was also chosen, with a tunneling face cross-sectional area S of 15.75 m2. The pressure airflow rates of Q press were set to 150, 300, 400, and 500 m3/min, while the suction airflow rates of Q pump were set to 100, 200, 285, and 333 m3/min. The distance from the pressure airflow exit to the tunneling face LE was set to 15 m, and the distance from the suction airflow exit LF to 5 m. Following the principles of dynamic similarity theory, similar pressure airflow rates Qpress were derived as 150, 300, 400, and 500 m3/min, while similar suction airflow rates Q pump were derived as 100, 200, 285, and 333 m3/min. The distance from the pressure airflow exit to the tunneling face L press was set at 15 m, and from the suction airflow exit L pump at 5 m. The corresponding results are illustrated in Fig. 7. Fig. 7Velocity profile cutout. Velocity profile cutout. Fig. 8Velocity planing surface. Velocity planing surface. The wind speed profile results in Fig. 8 indicate that the pressure gradient, along-path resistance, and the viscosity of the air itself influence the high-speed pressurized jet flow field formed by the rotating wind curtain. Along the exit x-axis direction, the wind speed of the rotating wind curtain rapidly decreases. By x = 2 m, the wind speed is already quite low. However, with the increase in pressurized air velocity and extraction air velocity, the intensity of the influence on the previously rotating wind curtain motion gradually increases, ultimately leading to the fragmentation of the generated rotating wind curtain and the appearance of gaps. Utilizing CFD numerical analysis software, simulations were conducted for jet wind speed v = 30 m/s, working angle of 75°, and spray pressure of 4 MPa under different auxiliary ventilation conditions to investigate the impact on the trajectory of droplet motion. The changing pattern of droplet motion trajectories over time is depicted in Fig. 9. Fig. 9Particle trajectory. Particle trajectory. From the above four simulation result graphs, we conclude that upon activating the external pressurized air duct of the shearer, air flows out from the pressurized air outlet. When the Pneumatic Spiral Spray Dedusting Device operates steadily, with increased pressurized air and extraction wind speeds, the impact intensity on the rotating wind curtain field gradually increases. During the process of expanding jet impact intensity, the pressurized air jet impacts the rotating droplets, causing them to deviate from their rotation trajectory, moving towards the negative x-axis direction. As the airflow increased, the diffusion of droplets drawn into the extraction air duct intensified. When the pressurized air volume Qpress was 3 m3/min and the extraction air volume Qpump was 285 m3/min, some droplets deviated from the rotation trajectory, and the spiral mist curtain gradually became unstable. Significant disruption occurred to the mist curtain formed by rotating droplets at the extraction duct, as depicted in Fig. 9b. The Pneumatic Spiral Spray Dedusting Device entered the extraction air duct, originally forming a closed presentation against the tunnel wall, revealing a gap. The gap in the mist curtain intensified with the increase in the Qpress and Qpump. As depicted in Fig. 9c and d, the Pneumatic Spiral Spray Dedusting Device has been completely disrupted, leading to a gradual failure of the Pneumatic Spiral Spray Dedusting System. Atomization disturbance experimental analysis The atomization disturbance similarity experiment employed the same approach as the physical and scale model similarity experiment, aiming to investigate the influence of different ventilation conditions on forming the Pneumatic Spiral Spray Dedusting System under various operating conditions. This study aimed to determine the system’s resistance to disturbance under both push-type ventilation dust removal and long-pressure and short-pumping ventilation conditions. Using the same main parameters of the Pneumatic Spiral Spray Dedusting System as in “Simulation results of the airflow field under the disturbance conditions of longpressureand short-pumping ventilation” section, the ventilation conditions included push-type, long-pressure, and short-pumping ventilation. The experimental procedure involved activating the Pneumatic Spiral Spray Dedusting System first and initiating the ventilation system to the operating conditions. The corresponding experimental results are reported in Table 1. Table 1Resistance to disturbance results.NumberVentilation conditionsSimilar position/mSimilar airflow/(m3 min−1)Fog curtain integrityL pressL pumpQ pressQ pump1Long-pressure and Short-pumping155150100complete2Long-pressure and Short-pumping155300200relatively complete3Long-pressure and Short-pumping155400285dispersed4Long-pressure and Short-pumping155500333dispersed Table 1Resistance to disturbance results.NumberVentilation conditionsSimilar position/mSimilar airflow/(m3 min−1)Fog curtain integrityL pressL pumpQ pressQ pump1Long-pressure and Short-pumping155150100complete2Long-pressure and Short-pumping155300200relatively complete3Long-pressure and Short-pumping155400285dispersed4Long-pressure and Short-pumping155500333dispersed Resistance to disturbance results. As shown in Table 1, by selecting similar measurement point locations, it can be observed that as the pressure air volume and exhaust air volume gradually increase, the fog curtain begins to diverge at a pressure air volume of 150–300 m3/min and an exhaust air volume of 1–2 m3/min. When the pressure air volume exceeds 400 m3/min and the exhaust air volume exceeds 280 m3/min, the fog curtain exhibits a divergent state. Comprehensive dust control experiment under ventilation disturbance Overall system arrangement Based on the described experimental equipment structure of the integrated dust control system layout, Fig. 10 depicts the three-dimensional schematic diagram of the designed pneumatic spiral spray dedusting integrated dust control experimental system, and the semi-enclosed similar experimental platform of the pneumatic vortex mist integrated dust control system was selected with a similarity ratio of 10:1 for experiments. In this system, a centrifugal fan generated a stable rotating wind curtain, with a vector frequency converter adjusting the gas output flow and controlling the outlet wind speed, ensuring the stability of the formed mist curtain under different jet speeds. The JDT-12 A high-pressure atomizer provided pressurized water for the pneumatic spiral spray dedusting device. The water source was from the laboratory water tank storing tap water. Besides, the nozzles were mounted on the straight-through nozzle holder and connected to the three-way, straight-through nozzle holder and the output end of the high-pressure atomizer through PE pipes. The pressure regulator on the high-pressure atomizer was used to adjust the output pressure and flow of the water pump. The equipment is illustrated in Figs. 11 and 12. Fig. 103D schematic diagram of the comprehensive dust control experimental system. 3D schematic diagram of the comprehensive dust control experimental system. Fig. 11Illustrates the experimental platform of the dust control system. Illustrates the experimental platform of the dust control system. Fig. 12Pneumatic spiral spray dedusting system. (a) Three-stage high-pressure cold fog nozzle (b) High-pressure atomizer (c) Annular air duct (d) Axial flow fan (e) Vector frequency converter. Pneumatic spiral spray dedusting system. (a) Three-stage high-pressure cold fog nozzle (b) High-pressure atomizer (c) Annular air duct (d) Axial flow fan (e) Vector frequency converter. Dust reduction experiment design During the experiment, the atmospheric conditions in the laboratory were set at Pamb = 0.1 MPa and Tamb = 298 K. Besides, a homemade dust generator was placed on the walls of a semi-enclosed experimental chamber as the dust source. Finely crushed dust from raw coal was used, and particles larger than 250 μm were removed using a 60-mesh sieve. The dust emission rate was set at 30 g/min. Stable dusting operations were simulated, and with the pneumatic spiral spray dedusting system turned off, dust concentrations at designated points 1 and 2 were measured using the CCZ-1000 direct-reading dust meter without any dust control measures (dry operation). When the pneumatic spiral spray dedusting system (Pneumatic spiral spray dedusting) was activated, the experiment space became humid, and small droplets carried by the pressurized airflow filled the entire tunnel. The high humidity in the confined space significantly affected the dust concentration meter’s dust control accuracy. For comprehensive dust control (wet operation), the AKFC-92 A dust sampler was used to sample dust in the air. The dust mass concentration in the air was determined using the formula by analyzing the increase in unit mass of the filter membrane before and after dust sampling, along with the sampling flow rate of the equipment. Based on the comprehensive simulation of atomization disturbance, dust reduction experiments were conducted under conditions that could form a relatively complete mist curtain. The experimental conditions included: Operating the dust generation device alone (using the CCZ-1000 laser dust concentration sampler). Activating the Pneumatic Spiral Spray Dedusting system, turning on the long-pressure and short-pumping ventilation equipment, and using a dust sampler to measure the dust concentration distribution at the measurement points (atomization pressure of 4 MPa, atomization working angle of 75°, jet velocity of 30 m/s; pressure airflow rates of 1.5, 3 m3/min, and suction airflow rates of 1, 2 m3/min). Operating the dust generation device alone (using the CCZ-1000 laser dust concentration sampler). Operating the dust generation device alone (using the CCZ-1000 laser dust concentration sampler). Activating the Pneumatic Spiral Spray Dedusting system, turning on the long-pressure and short-pumping ventilation equipment, and using a dust sampler to measure the dust concentration distribution at the measurement points (atomization pressure of 4 MPa, atomization working angle of 75°, jet velocity of 30 m/s; pressure airflow rates of 1.5, 3 m3/min, and suction airflow rates of 1, 2 m3/min). Activating the Pneumatic Spiral Spray Dedusting system, turning on the long-pressure and short-pumping ventilation equipment, and using a dust sampler to measure the dust concentration distribution at the measurement points (atomization pressure of 4 MPa, atomization working angle of 75°, jet velocity of 30 m/s; pressure airflow rates of 1.5, 3 m3/min, and suction airflow rates of 1, 2 m3/min). Fig. 13Experimental point location. Experimental point location. The formula for determining the mass concentration of dust in the air is:\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\:C=\frac{\left({m}_{2}-{m}_{1}\right)}{Qt}$$\end{document} Where: C is the mass concentration of dust, mg/m3; Is the mass of the sampled filter membrane, mg; Is the mass of the filter membrane before sampling, mg; Q is the sampled flow rate, L/min; t is the sampling time, min. Following the requirements of the national occupational safety and health industry standard “Technical Specification for Comprehensive Dust Control in Coal Mines (AQ1020-2006)” regarding dust detection, two dust measurement points were arranged at the operator’s position of the roadheader and 0.5 m behind the roadheader body (1.5 m above the breathing zone of the personnel working on the floor). These points were designated for the measurement of dust concentrations. Quantitative testing evaluated the dust reduction effectiveness of the Pneumatic Spiral Spray Dedusting technology integrated with the comprehensive ventilation system within a sealed experimental roadway. Measurement Point 1 was situated at a height of 0.75 m from the operator and 0.15 m above the breathing zone. Measurement Point 2 was positioned 1.5 m on the return air side of the machine unit and 0.15 m above the breathing zone. The arrangement of measurement points is depicted in Fig. 13. Experimental results and discussion on atomized dust reduction Five data sets were obtained for the total and respirable dust concentrations under two dust suppression operating conditions: without any dust control measures and with the Pneumatic Spiral Spray Dedusting system integrated with long-pressure and short-pumping ventilation. The distribution of dust concentrations under different operating conditions is reported in Tables 2 and 3. Table 2Total dust sampling concentrations.ConditionsMeasurement point locationSampling Time/minFlow Rate/L·min− 1Filter weight/mgDust mass/mgNet weight/mgTotal dust concentration/mg m−3Operating condition11–––––433.9Operating condition12–––––306.8Operating condition 2(1)122085.485.80.410Operating condition 2(1)222091.391.50.25Operating condition 2(2)122086.987.40.512.5Operating condition 2(2)222088.589.40.922.5 Table 2Total dust sampling concentrations.ConditionsMeasurement point locationSampling Time/minFlow Rate/L·min− 1Filter weight/mgDust mass/mgNet weight/mgTotal dust concentration/mg m−3Operating condition11–––––433.9Operating condition12–––––306.8Operating condition 2(1)122085.485.80.410Operating condition 2(1)222091.391.50.25Operating condition 2(2)122086.987.40.512.5Operating condition 2(2)222088.589.40.922.5 Total dust sampling concentrations. Table 3Respirable dust sampling concentration.ConditionsMeasurement point locationSampling Time/minFlow rate/L min−1Filter weight/mgDust mass/mgNet weight/mgTotal dust concentration/mg m−3Operating condition11––––/–135.5Operating condition12–––––70.2Operating condition 2(1)122088.488.80.410Operating condition 2(1)222089.289.30.12.5Operating condition 2(2)12208888.20.25Operating condition 2(2)222090.190.20.12.5 Table 3Respirable dust sampling concentration.ConditionsMeasurement point locationSampling Time/minFlow rate/L min−1Filter weight/mgDust mass/mgNet weight/mgTotal dust concentration/mg m−3Operating condition11––––/–135.5Operating condition12–––––70.2Operating condition 2(1)122088.488.80.410Operating condition 2(1)222089.289.30.12.5Operating condition 2(2)12208888.20.25Operating condition 2(2)222090.190.20.12.5 Respirable dust sampling concentration. Tables 2 and 3 show the concentration distribution of total dust and respirable dust under multiple working conditions for atomization dust suppression. In working condition 1, no dust suppression equipment is activated, allowing for natural sedimentation, which serves as the experimental reference for this study. In working condition 2(1), only the pneumatic vortex fog curtain dust control system is activated, and the dust concentration at the measurement points is recorded. In working condition 2(2), both the long-pressure short-pumping system and the pneumatic vortex fog curtain dust control system are activated, and the dust concentration at the measurement points is recorded. Based on the data from the semi-enclosed atomization dust suppression experimental platform under different working conditions of the pneumatic vortex fog curtain dust control system, and using the data from the tables and corresponding formulas, the dust suppression efficiency for total dust and respirable dust at measurement point 1 under working condition 2 is calculated as follows:8\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\eta _{{DCI}} = \frac{{433.9 - 12.5}}{{433.9}} \times 100\% = 97.1\%$$\end{document}9\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\eta _{{RDCI}} = \frac{{135.5 - 7.5}}{{130.2}} \times 100\% = 94.5\%$$\end{document} Similarly, based on formulas (8) and (9), under the conditions of Pneumatic Spiral Spray Dedusting integrated with long-pressure and short-pumping ventilation, the dust reduction efficiency at Measurement Point 1 in the advancing roadway was 97.6% and 97.1% for total dust, and 92.6% and 96.3% for respirable dust. At Measurement Point 2, the total dust reduction efficiency was 98.4% and 92.7%, while the respirable dust reduction efficiency was 96.4% and 96.4%. The comparative efficiency of the dust reduction system at Measurement Points 1 and 2 for the roadheader under long-pressure and short-pumping ventilation integrated with Pneumatic Spiral Spray Dedusting is illustrated in Fig. 14. In the previous experiments29, it was observed that once the mist curtain is disrupted, the dust reduction efficiency drops to around 85%. Therefore, this experiment focuses on studying the dust reduction efficiency under the condition of a disrupted mist curtain. Fig. 14Comprehensive dust reduction efficiency comparison under long-pressure and short-pumping ventilation. Comprehensive dust reduction efficiency comparison under long-pressure and short-pumping ventilation. Through the comparison of comprehensive dust suppression efficiency under long-pressure short-pumping ventilation in Fig. 14, it can be seen that as the air volume increases, the dust concentration at measurement point 1 (driver’s position) decreases, and the dust suppression efficiency steadily rises, reaching a maximum of 97.7%. However, at measurement point 2, the dust suppression efficiency first increases and then decreases. This is because the increase in pressure air volume intensifies the impact on the pneumatic vortex fog curtain, and the negative pressure generated by the exhaust air causes some droplets to deviate from their original rotational trajectory, creating gaps in the enclosure of the roadway, resulting in an increase in dust concentration at measurement point 2 and a decrease in dust suppression efficiency. Due to the combined effect of the pressure air inlet and the exhaust air outlet, the destruction of the pneumatic vortex fog curtain is more severe. The experiment only considered the atomization dust suppression efficiency, so only two ventilation conditions were selected: Q pressure at 1.5 and 3 m3/min, and Q exhaust at 1 and 2 m3/min. Consequently, the total dust suppression efficiency at measurement point 1 was 97.6% and 97.1%, and the respirable dust suppression efficiency was 92.6% and 96.3%, respectively. At measurement point 2, the total dust suppression efficiency was 97.6% and 97.1%, and the respirable dust suppression efficiency was 96.4% and 96.4%. At measurement point 2, due to the disruption of the fog curtain by the ventilation conditions, dust escape occurred, causing an increase in dust concentration in the rear. Conclusions Both similar systems and numerical simulations confirm that under the disturbance of long-pressure and short-pumping ventilation conditions, when Q press is 400 m3/min and Q pump is 285 m3/min, the Velocity Planing Surface diagram indicates that the air curtain begins to experience ventilation-induced disruptions, resulting in openings. Simultaneously, gaps in the mist curtain also appear on the return airflow side. This proves that the pneumatic mist curtain can maintain its integrity at specific airflow rates, exhibiting a certain level of disturbance resistance. Combined with the pressure air duct for the tunneling face, it achieves comprehensive control, enveloping the dust source on the tunneling face.In specific conditions of long-pressure and short-pumping ventilation disturbance during the tunneling face pneumatic spiral spray dedusting experiment, it proves the disturbance resistance of the mist curtain wall formed by the aforementioned pneumatic spiral spray dedusting system. The average respirable dust concentration drops from 135.5 mg/m3 to 2.5 mg/m3 at the driver’s working location. Similarly, at 15 m on the downwind side of the coal-cutting machine, the average concentration of total dust decreases from 70.2 mg/m3 to 2.5 mg/m3. This indicates that the pneumatic spiral spray dedusting system maintains high dust suppression performance even under disturbance.Furthermore, the system continues to provide effective dust reduction performance under the existing disturbance of long-pressure and short-pumping ventilation, significantly improving the working environment of the tunneling face. By employing the pneumatic spiral spray dedusting system described above, the water consumption of this dust control system is equivalent to that of traditional spray systems. However, the formed mist curtain wall efficiently captures dust. Under undisturbed ventilation conditions, the dust reduction efficiency for both total and respirable dust exceeds 92%, achieving the highly efficient dust suppression goal with the pneumatic spiral spray dedusting system. Integrating the rotating mist curtain control system with the long-pressure and short-pumping system has distinct advantages in controlling dust pollution in underground mines. This ensures the health of tunneling workers and contributes to reducing energy consumption in daily production for enterprises.The dust control method provided in this study can not only improve the dust removal efficiency, but also reduce the water and energy consumption of the dust removal equipment, which meets the requirements of green mine and clean production, and is conducive to the sustainable development of coal mining. Numerical simulation and similar experiments have proved that the technology can significantly reduce the dust concentration in mines, tunnels and other workplaces, improve air quality, reduce the risk of workers inhaling harmful dust, and thus reduce the incidence of occupational diseases, which is of great significance for workers’ health protection. Both similar systems and numerical simulations confirm that under the disturbance of long-pressure and short-pumping ventilation conditions, when Q press is 400 m3/min and Q pump is 285 m3/min, the Velocity Planing Surface diagram indicates that the air curtain begins to experience ventilation-induced disruptions, resulting in openings. Simultaneously, gaps in the mist curtain also appear on the return airflow side. This proves that the pneumatic mist curtain can maintain its integrity at specific airflow rates, exhibiting a certain level of disturbance resistance. Combined with the pressure air duct for the tunneling face, it achieves comprehensive control, enveloping the dust source on the tunneling face. Both similar systems and numerical simulations confirm that under the disturbance of long-pressure and short-pumping ventilation conditions, when Q press is 400 m3/min and Q pump is 285 m3/min, the Velocity Planing Surface diagram indicates that the air curtain begins to experience ventilation-induced disruptions, resulting in openings. Simultaneously, gaps in the mist curtain also appear on the return airflow side. This proves that the pneumatic mist curtain can maintain its integrity at specific airflow rates, exhibiting a certain level of disturbance resistance. Combined with the pressure air duct for the tunneling face, it achieves comprehensive control, enveloping the dust source on the tunneling face. In specific conditions of long-pressure and short-pumping ventilation disturbance during the tunneling face pneumatic spiral spray dedusting experiment, it proves the disturbance resistance of the mist curtain wall formed by the aforementioned pneumatic spiral spray dedusting system. The average respirable dust concentration drops from 135.5 mg/m3 to 2.5 mg/m3 at the driver’s working location. Similarly, at 15 m on the downwind side of the coal-cutting machine, the average concentration of total dust decreases from 70.2 mg/m3 to 2.5 mg/m3. This indicates that the pneumatic spiral spray dedusting system maintains high dust suppression performance even under disturbance. In specific conditions of long-pressure and short-pumping ventilation disturbance during the tunneling face pneumatic spiral spray dedusting experiment, it proves the disturbance resistance of the mist curtain wall formed by the aforementioned pneumatic spiral spray dedusting system. The average respirable dust concentration drops from 135.5 mg/m3 to 2.5 mg/m3 at the driver’s working location. Similarly, at 15 m on the downwind side of the coal-cutting machine, the average concentration of total dust decreases from 70.2 mg/m3 to 2.5 mg/m3. This indicates that the pneumatic spiral spray dedusting system maintains high dust suppression performance even under disturbance. Furthermore, the system continues to provide effective dust reduction performance under the existing disturbance of long-pressure and short-pumping ventilation, significantly improving the working environment of the tunneling face. By employing the pneumatic spiral spray dedusting system described above, the water consumption of this dust control system is equivalent to that of traditional spray systems. However, the formed mist curtain wall efficiently captures dust. Under undisturbed ventilation conditions, the dust reduction efficiency for both total and respirable dust exceeds 92%, achieving the highly efficient dust suppression goal with the pneumatic spiral spray dedusting system. Integrating the rotating mist curtain control system with the long-pressure and short-pumping system has distinct advantages in controlling dust pollution in underground mines. This ensures the health of tunneling workers and contributes to reducing energy consumption in daily production for enterprises. Furthermore, the system continues to provide effective dust reduction performance under the existing disturbance of long-pressure and short-pumping ventilation, significantly improving the working environment of the tunneling face. By employing the pneumatic spiral spray dedusting system described above, the water consumption of this dust control system is equivalent to that of traditional spray systems. However, the formed mist curtain wall efficiently captures dust. Under undisturbed ventilation conditions, the dust reduction efficiency for both total and respirable dust exceeds 92%, achieving the highly efficient dust suppression goal with the pneumatic spiral spray dedusting system. Integrating the rotating mist curtain control system with the long-pressure and short-pumping system has distinct advantages in controlling dust pollution in underground mines. This ensures the health of tunneling workers and contributes to reducing energy consumption in daily production for enterprises. The dust control method provided in this study can not only improve the dust removal efficiency, but also reduce the water and energy consumption of the dust removal equipment, which meets the requirements of green mine and clean production, and is conducive to the sustainable development of coal mining. Numerical simulation and similar experiments have proved that the technology can significantly reduce the dust concentration in mines, tunnels and other workplaces, improve air quality, reduce the risk of workers inhaling harmful dust, and thus reduce the incidence of occupational diseases, which is of great significance for workers’ health protection. The dust control method provided in this study can not only improve the dust removal efficiency, but also reduce the water and energy consumption of the dust removal equipment, which meets the requirements of green mine and clean production, and is conducive to the sustainable development of coal mining. Numerical simulation and similar experiments have proved that the technology can significantly reduce the dust concentration in mines, tunnels and other workplaces, improve air quality, reduce the risk of workers inhaling harmful dust, and thus reduce the incidence of occupational diseases, which is of great significance for workers’ health protection.