Protocol for manufacturing photosynthetic cyanobacterial cell-based living building materials Authors: Yongjun Son, Jihyeon Min, Jiyoon Park, Chongku Yi, Woojun Park Published: 2024 ABSTRACT SummaryCement-free and photosynthetic cyanobacterial cell-based living building materials (LBMs) can be manufactured using microbially induced calcium carbonate precipitation (MICP) technology. Here, we present a protocol for cultivating Leptolyngbya boryana GGD and manufacturing LBMs using a sand-gelatin solution. We describe steps for fabricating acrylic molds and mixing abiotic substances with cyanobacterial cells for constructing LBMs. We then detail the procedures for analyzing the compressive strengths of our LBMs with or without the cyanobacterial cells using a universal testing machine (UTM).For complete details on the use and execution of this protocol, please refer to Son et al.1Subject areas: Cell culture, Microbiology, Biotechnology and bioengineering, Material sciences Before you begin Cement-free and regenerative living building materials (LBMs) can be engineered by incorporating calcium carbonate precipitation (CCP)-capable cyanobacteria into an inert sand-gelatin scaffold.2,3 During photosynthetic growth, these cyanobacterial cells precipitate CaCO₃ in the presence of calcium ions. This biogenic CaCO₃ fills the voids within the porous sand-gelatin matrix, thereby enhancing the mechanical properties of the quasi-brittle LBMs. To apply this technology, we isolated the photosynthetic and axenic filamentous cyanobacterium Leptolyngbya boryana GGD, as previously described.1 Our isolated GGD strain precipitates CaCO₃ in BG11 medium supplemented with CaCl2, as confirmed by field emission scanning electron microscopy (FE-SEM), energy-dispersive X-ray (EDX), and X-ray diffractometry (XRD) analyses.4,5 We optimized the culture conditions for the GGD strain using genomic analyses and phenotypic assays, including growth, nitrogen availability, and biofilm formation, to maximize its CCP capability.6,7 This protocol outlines the preparation of L. boryana GGD cultures and sand-gelatin mixtures for LBM fabrication. Additionally, we detail the procedure for measuring the compressive strengths of LBMs in accordance with the American Society for Testing and Materials (ASTM) C346 standard method. Preparation of the reagents Timing: 1 h This step describes the preparation of BG11 media for the cultivation of cyanobacterial cells. Note: Prepare stocks for the following reagent. 1.Four stocks for BG11 medium.a.Dissolve stock 1 [ethylene-diamine-tetraacetic acid (EDTA, 0.35 mM), ferric ammonium (2.3 mM), citric acid monohydrate (2.9 mM), and calcium chloride dihydrate (24.5 mM)] with distilled water (DW) into an amber conical tube (50 mL).b.Dissolve stock 2 [Magnesium sulfate heptahydrate (30.45 mM)] with DW into an amber conical tube (50 mL).c.Dissolve stock 3 [Potassium phosphate monobasic (30 mM)] with DW into an amber conical tube (50 mL).d.Prepare stock 4 [trace metal mix A5 with Co solution (1 mL/L)].e.Filtrate stocks 1–3 using a 0.22 μm pore size filter before use to ensure long-term storage and prevent potential contamination by external bacteria in DW. Four stocks for BG11 medium.a.Dissolve stock 1 [ethylene-diamine-tetraacetic acid (EDTA, 0.35 mM), ferric ammonium (2.3 mM), citric acid monohydrate (2.9 mM), and calcium chloride dihydrate (24.5 mM)] with distilled water (DW) into an amber conical tube (50 mL).b.Dissolve stock 2 [Magnesium sulfate heptahydrate (30.45 mM)] with DW into an amber conical tube (50 mL).c.Dissolve stock 3 [Potassium phosphate monobasic (30 mM)] with DW into an amber conical tube (50 mL).d.Prepare stock 4 [trace metal mix A5 with Co solution (1 mL/L)].e.Filtrate stocks 1–3 using a 0.22 μm pore size filter before use to ensure long-term storage and prevent potential contamination by external bacteria in DW. a.Dissolve stock 1 [ethylene-diamine-tetraacetic acid (EDTA, 0.35 mM), ferric ammonium (2.3 mM), citric acid monohydrate (2.9 mM), and calcium chloride dihydrate (24.5 mM)] with distilled water (DW) into an amber conical tube (50 mL). Dissolve stock 1 [ethylene-diamine-tetraacetic acid (EDTA, 0.35 mM), ferric ammonium (2.3 mM), citric acid monohydrate (2.9 mM), and calcium chloride dihydrate (24.5 mM)] with distilled water (DW) into an amber conical tube (50 mL). b.Dissolve stock 2 [Magnesium sulfate heptahydrate (30.45 mM)] with DW into an amber conical tube (50 mL). Dissolve stock 2 [Magnesium sulfate heptahydrate (30.45 mM)] with DW into an amber conical tube (50 mL). c.Dissolve stock 3 [Potassium phosphate monobasic (30 mM)] with DW into an amber conical tube (50 mL). Dissolve stock 3 [Potassium phosphate monobasic (30 mM)] with DW into an amber conical tube (50 mL). d.Prepare stock 4 [trace metal mix A5 with Co solution (1 mL/L)]. Prepare stock 4 [trace metal mix A5 with Co solution (1 mL/L)]. e.Filtrate stocks 1–3 using a 0.22 μm pore size filter before use to ensure long-term storage and prevent potential contamination by external bacteria in DW. Filtrate stocks 1–3 using a 0.22 μm pore size filter before use to ensure long-term storage and prevent potential contamination by external bacteria in DW. CRITICAL: All stock solutions must be stored at 4°C and protected from light to prevent their oxidation. Note: Store the stock at 4°C for up to 1 year. 2.Preparation of BG11 liquid medium (1 L).a.Transfer into DW (950 mL) the prepared four stocks (each 1 mL) in Erlenmeyer flasks (2 L) and mix with a magnetic stirrer.b.Thoroughly dissolve both NaNO3 (17.7 mM) and Na2CO3 (200 μM) in the Erlenmeyer flasks with stock solutions.c.Adjust pH 7.5 to the BG11 medium using HCl (1 M) solution.CRITICAL: When adjusting the pH, it is crucial to ensure it does not drop below pH 7.5.d.Seal the neck of the flasks with foil and sterilize it using an autoclave (at 121°C, 20 min).e.Place the sterile BG11 medium at room temperature before use. Preparation of BG11 liquid medium (1 L).a.Transfer into DW (950 mL) the prepared four stocks (each 1 mL) in Erlenmeyer flasks (2 L) and mix with a magnetic stirrer.b.Thoroughly dissolve both NaNO3 (17.7 mM) and Na2CO3 (200 μM) in the Erlenmeyer flasks with stock solutions.c.Adjust pH 7.5 to the BG11 medium using HCl (1 M) solution.CRITICAL: When adjusting the pH, it is crucial to ensure it does not drop below pH 7.5.d.Seal the neck of the flasks with foil and sterilize it using an autoclave (at 121°C, 20 min).e.Place the sterile BG11 medium at room temperature before use. a.Transfer into DW (950 mL) the prepared four stocks (each 1 mL) in Erlenmeyer flasks (2 L) and mix with a magnetic stirrer. Transfer into DW (950 mL) the prepared four stocks (each 1 mL) in Erlenmeyer flasks (2 L) and mix with a magnetic stirrer. b.Thoroughly dissolve both NaNO3 (17.7 mM) and Na2CO3 (200 μM) in the Erlenmeyer flasks with stock solutions. Thoroughly dissolve both NaNO3 (17.7 mM) and Na2CO3 (200 μM) in the Erlenmeyer flasks with stock solutions. c.Adjust pH 7.5 to the BG11 medium using HCl (1 M) solution.CRITICAL: When adjusting the pH, it is crucial to ensure it does not drop below pH 7.5. Adjust pH 7.5 to the BG11 medium using HCl (1 M) solution.CRITICAL: When adjusting the pH, it is crucial to ensure it does not drop below pH 7.5. CRITICAL: When adjusting the pH, it is crucial to ensure it does not drop below pH 7.5. d.Seal the neck of the flasks with foil and sterilize it using an autoclave (at 121°C, 20 min). Seal the neck of the flasks with foil and sterilize it using an autoclave (at 121°C, 20 min). e.Place the sterile BG11 medium at room temperature before use. Place the sterile BG11 medium at room temperature before use. Preparation of the abiotic materials for LBMs Timing: 2 days This step describes the preparation of abiotic materials for LBMs manufacturing. 3.Preparation of the sterile sand for manufacturing LBMs.a.Put standard ISO sand (1,350 g) into the beaker (1 L).b.Wash the sand three times using DW to remove its salt and other minerals.c.Thoroughly dry the wet sand in a dry oven at 110°C for 16 h.d.Sterilize the dried sand in the beaker (1 L) to remove its external bacteria using an autoclave (at 121°C, 20 min).Optional: The use of autoclaved sand can minimize the growth of external bacteria within the LBMs during the curing period.e.Place the sterile sand in the dry oven (at 110°C) before use. Preparation of the sterile sand for manufacturing LBMs.a.Put standard ISO sand (1,350 g) into the beaker (1 L).b.Wash the sand three times using DW to remove its salt and other minerals.c.Thoroughly dry the wet sand in a dry oven at 110°C for 16 h.d.Sterilize the dried sand in the beaker (1 L) to remove its external bacteria using an autoclave (at 121°C, 20 min).Optional: The use of autoclaved sand can minimize the growth of external bacteria within the LBMs during the curing period.e.Place the sterile sand in the dry oven (at 110°C) before use. a.Put standard ISO sand (1,350 g) into the beaker (1 L). Put standard ISO sand (1,350 g) into the beaker (1 L). b.Wash the sand three times using DW to remove its salt and other minerals. Wash the sand three times using DW to remove its salt and other minerals. c.Thoroughly dry the wet sand in a dry oven at 110°C for 16 h. Thoroughly dry the wet sand in a dry oven at 110°C for 16 h. d.Sterilize the dried sand in the beaker (1 L) to remove its external bacteria using an autoclave (at 121°C, 20 min).Optional: The use of autoclaved sand can minimize the growth of external bacteria within the LBMs during the curing period. Sterilize the dried sand in the beaker (1 L) to remove its external bacteria using an autoclave (at 121°C, 20 min).Optional: The use of autoclaved sand can minimize the growth of external bacteria within the LBMs during the curing period. Optional: The use of autoclaved sand can minimize the growth of external bacteria within the LBMs during the curing period. e.Place the sterile sand in the dry oven (at 110°C) before use. Place the sterile sand in the dry oven (at 110°C) before use. 4.Preparation of transparent acrylic mold.a.Fabricate the piece of transparent acrylic with a thickness of 0.5 mm for the assembly mold used in manufacturing LBMs (Figure 1).b.Attach polytetrafluoroethylene (PTFE) sheet tape (thickness, 70 μm) to the inside of the acrylic mold, where the abiotic mixtures will be placed, to facilitate easy detachment of curing LBMs. Preparation of transparent acrylic mold.a.Fabricate the piece of transparent acrylic with a thickness of 0.5 mm for the assembly mold used in manufacturing LBMs (Figure 1).b.Attach polytetrafluoroethylene (PTFE) sheet tape (thickness, 70 μm) to the inside of the acrylic mold, where the abiotic mixtures will be placed, to facilitate easy detachment of curing LBMs. a.Fabricate the piece of transparent acrylic with a thickness of 0.5 mm for the assembly mold used in manufacturing LBMs (Figure 1). Fabricate the piece of transparent acrylic with a thickness of 0.5 mm for the assembly mold used in manufacturing LBMs (Figure 1). b.Attach polytetrafluoroethylene (PTFE) sheet tape (thickness, 70 μm) to the inside of the acrylic mold, where the abiotic mixtures will be placed, to facilitate easy detachment of curing LBMs. Attach polytetrafluoroethylene (PTFE) sheet tape (thickness, 70 μm) to the inside of the acrylic mold, where the abiotic mixtures will be placed, to facilitate easy detachment of curing LBMs. Assembly and dimensions of acrylic cubic and cuboid molds Each mold consists of individual bottom and wall panels designed to interlock. (A) Disassembled components of the molds. The top row shows the cubic mold parts, and the bottom row displays the cuboid mold parts. (B and C) Assembly process and dimensions of the acrylic cubic and cuboid mold, respectively. Key resources table REAGENT or RESOURCESOURCEIDENTIFIERBacterial and virus strainsLeptolyngbya boryana GGDN/AKACC 23245Chemicals, peptides, and recombinant proteinsEDTA (Na2MG)BioshopEDT001.500Ferric ammonium [ammonium iron(lll) citrate]SigmaF5879Citric acid monohydrateSigmaC1909Calcium chloride dihydrate (CaCl2·H2O)SigmaC8106Sodium carbonate (Na2CO3)Sigma222321Sodium nitrate (NaNO3)SigmaS5506Magnesium sulfate heptahydrate (MgSO4·7H2O)Sigma230391Potassium phosphate monobasic (K2HPO4·3H2O)SigmaP0662Potassium nitrate (KNO3)Sigma221295Trace metal mix A5 with CoSigma92949AgarSigmaA6686Sodium chloride (NaCl)SigmaS9888Potassium chloride (KCl)SigmaP3911Sodium phosphate dibasic (Na2HPO4)SigmaS9763Potassium phosphate monobasic (KH2PO4)Sigma529568Sodium hydroxide (NaOH)Sigma221465Hydrogen chloride (HCl)Sigma258148Methanol (MeOH)Sigma179337OtherCulture flask (75 cm2)SPL Life Sciences70175Culture flask (175 cm2)SPL Life Sciences71175Conical tube (50 mL)SPL Life Sciences50050Amber conical tube (50 mL)SPL Life Sciences54150Standard sand CEN EN 196-1NORMERSANDISO 679:2009Standard aluminum foilKirklandRK611CA Syringe filters 0.22 μm, sterileFiltraTECHSF25CA22SMagnetic barN/AN/APlastering toolN/AN/ANitrile glovesAnsell93-733-SSpatulaN/AN/APolytetrafluoroethylene sheet tape (70 μm)TommyhecoT01-140-101Lightning rod (30 g)N/AN/AUniversal testing machineInstronINSTRON 3366Acrylic moldsN/AN/A Materials and equipment Stock 1 for BG11 mediumReagentFinal concentrationAmountEthylene-diamine-tetraacetic acid (EDTA)0.35 mMN/AFerric ammonium2.3 mMN/ACitric acid monohydrate2.9 mMN/ACalcium chloride dihydrate24.5 mMN/A Stock 1 for BG11 medium Stock 2 for BG11 mediumReagentFinal concentrationAmountMagnesium sulfate heptahydrate30.45 mMN/A Stock 2 for BG11 medium Stock 3 for BG11 mediumReagentFinal concentrationAmountPotassium phosphate monobasic30 mMN/A Stock 3 for BG11 medium Note: Prepare and use the stocks 1–3 on the day of the experiment, storing them at 4°C until use. The maximum storage time is 1 year. Step-by-step method details Part 1: Procedure for the cultivation of photosynthetic cyanobacterial cells Timing: 10 days (for steps 1 a–r) Timing: 7 days (for steps 1 s–u) This step describes the cultivation process of photosynthetic cyanobacterial cells. 1.Cultivation of photosynthetic cyanobacterial cells for inoculating LBMs.a.Scrape a single colony of Leptolyngbya boryana GGD cells from the BG11 agar plate using a sterile needle (Figures 2A and 2B).b.Inoculate the GGD strain cells adhered to the needle into fresh BG11 medium (50 mL) in a sterile culture flask (75 cm2).c.Incubate cyanobacterial cells at 28°C under a light intensity of 25 μmol m−2 s−1 with a 12-h:12-h light: dark photoperiod for 10 days.d.Detach proliferative cyanobacterial cells from the bottom of the culture flask by using a scraper.CRITICAL: This step is very important to avoid contamination by external bacteria.e.Centrifuge the collected cell cultures into the sterile conical tube (50 mL) for 10 min, 7,000 g at 28°C.f.Completely remove the cell-free supernatants, leaving only the cells.g.Wash the harvested cells three times with sterile BG11 (15 mL) (Figure 2C).CRITICAL: The washing step with sterile BG11 broth is necessary to remove metabolic byproducts generated during the growth of cyanobacterial cells. The accumulated byproducts can potentially affect the compressive strength of LBMs. An amount of 15 mL of BG11 broth is sufficient to thoroughly resuspend and wash the harvested cyanobacterial cells.h.Transfer the washed cells (1 mL) to the three Eppendorf tubes (1.5 mL), respectively.i.Centrifuge (20,000 g at 4°C, 2 min) the three Eppendorf tubes and remove cell-free supernatants (900 μL) by the pipette.j.Add methanol (900 μL) into the Eppendorf tube with the remaining cells (100 μL).k.Place them at 4°C for 30 min under dark conditions.l.Centrifuge (at 100 g and 4°C for 1 min) the Eppendorf tubes.m.Carefully transfer the cell-free supernatants into the new Eppendorf tube (1.5 mL) excepting cell debris.n.Centrifuge (at 600 g and 4°C for 10 min) the new Eppendorf tubes containing chlorophyll-a.o.Transfer supernatants (200 μL) into the 96 well plates.p.Measure chlorophyll-a solutions at OD666 and OD653 using a microplate reader (TECAN, Switzerland).q.Chlorophyll-a (μg/mL) = (15.65 × OD666 − 7.34 × OD653).1r.Inoculate cells (200 μL) with chlorophyll-a concentration (20 μg/mL) fresh BG11 (300 mL) in ten sterile culture flasks (175 cm2).s.Incubate the cyanobacterial cells in the culture flasks at 28°C under a light intensity of 25 μmol m−2 s−1 with a 12-h:12-h light: dark photoperiod for 7 days.t.Measure chlorophyll-a concentration as previously described (steps 1 h-q).u.Adjust the cell density based on chlorophyll-a concentrations to 20 μg/mL in a 50 mL conical tube (50 g). Cultivation of photosynthetic cyanobacterial cells for inoculating LBMs.a.Scrape a single colony of Leptolyngbya boryana GGD cells from the BG11 agar plate using a sterile needle (Figures 2A and 2B).b.Inoculate the GGD strain cells adhered to the needle into fresh BG11 medium (50 mL) in a sterile culture flask (75 cm2).c.Incubate cyanobacterial cells at 28°C under a light intensity of 25 μmol m−2 s−1 with a 12-h:12-h light: dark photoperiod for 10 days.d.Detach proliferative cyanobacterial cells from the bottom of the culture flask by using a scraper.CRITICAL: This step is very important to avoid contamination by external bacteria.e.Centrifuge the collected cell cultures into the sterile conical tube (50 mL) for 10 min, 7,000 g at 28°C.f.Completely remove the cell-free supernatants, leaving only the cells.g.Wash the harvested cells three times with sterile BG11 (15 mL) (Figure 2C).CRITICAL: The washing step with sterile BG11 broth is necessary to remove metabolic byproducts generated during the growth of cyanobacterial cells. The accumulated byproducts can potentially affect the compressive strength of LBMs. An amount of 15 mL of BG11 broth is sufficient to thoroughly resuspend and wash the harvested cyanobacterial cells.h.Transfer the washed cells (1 mL) to the three Eppendorf tubes (1.5 mL), respectively.i.Centrifuge (20,000 g at 4°C, 2 min) the three Eppendorf tubes and remove cell-free supernatants (900 μL) by the pipette.j.Add methanol (900 μL) into the Eppendorf tube with the remaining cells (100 μL).k.Place them at 4°C for 30 min under dark conditions.l.Centrifuge (at 100 g and 4°C for 1 min) the Eppendorf tubes.m.Carefully transfer the cell-free supernatants into the new Eppendorf tube (1.5 mL) excepting cell debris.n.Centrifuge (at 600 g and 4°C for 10 min) the new Eppendorf tubes containing chlorophyll-a.o.Transfer supernatants (200 μL) into the 96 well plates.p.Measure chlorophyll-a solutions at OD666 and OD653 using a microplate reader (TECAN, Switzerland).q.Chlorophyll-a (μg/mL) = (15.65 × OD666 − 7.34 × OD653).1r.Inoculate cells (200 μL) with chlorophyll-a concentration (20 μg/mL) fresh BG11 (300 mL) in ten sterile culture flasks (175 cm2).s.Incubate the cyanobacterial cells in the culture flasks at 28°C under a light intensity of 25 μmol m−2 s−1 with a 12-h:12-h light: dark photoperiod for 7 days.t.Measure chlorophyll-a concentration as previously described (steps 1 h-q).u.Adjust the cell density based on chlorophyll-a concentrations to 20 μg/mL in a 50 mL conical tube (50 g). a.Scrape a single colony of Leptolyngbya boryana GGD cells from the BG11 agar plate using a sterile needle (Figures 2A and 2B). Scrape a single colony of Leptolyngbya boryana GGD cells from the BG11 agar plate using a sterile needle (Figures 2A and 2B). b.Inoculate the GGD strain cells adhered to the needle into fresh BG11 medium (50 mL) in a sterile culture flask (75 cm2). Inoculate the GGD strain cells adhered to the needle into fresh BG11 medium (50 mL) in a sterile culture flask (75 cm2). c.Incubate cyanobacterial cells at 28°C under a light intensity of 25 μmol m−2 s−1 with a 12-h:12-h light: dark photoperiod for 10 days. Incubate cyanobacterial cells at 28°C under a light intensity of 25 μmol m−2 s−1 with a 12-h:12-h light: dark photoperiod for 10 days. d.Detach proliferative cyanobacterial cells from the bottom of the culture flask by using a scraper.CRITICAL: This step is very important to avoid contamination by external bacteria. Detach proliferative cyanobacterial cells from the bottom of the culture flask by using a scraper.CRITICAL: This step is very important to avoid contamination by external bacteria. CRITICAL: This step is very important to avoid contamination by external bacteria. e.Centrifuge the collected cell cultures into the sterile conical tube (50 mL) for 10 min, 7,000 g at 28°C. Centrifuge the collected cell cultures into the sterile conical tube (50 mL) for 10 min, 7,000 g at 28°C. f.Completely remove the cell-free supernatants, leaving only the cells. Completely remove the cell-free supernatants, leaving only the cells. g.Wash the harvested cells three times with sterile BG11 (15 mL) (Figure 2C).CRITICAL: The washing step with sterile BG11 broth is necessary to remove metabolic byproducts generated during the growth of cyanobacterial cells. The accumulated byproducts can potentially affect the compressive strength of LBMs. An amount of 15 mL of BG11 broth is sufficient to thoroughly resuspend and wash the harvested cyanobacterial cells. Wash the harvested cells three times with sterile BG11 (15 mL) (Figure 2C).CRITICAL: The washing step with sterile BG11 broth is necessary to remove metabolic byproducts generated during the growth of cyanobacterial cells. The accumulated byproducts can potentially affect the compressive strength of LBMs. An amount of 15 mL of BG11 broth is sufficient to thoroughly resuspend and wash the harvested cyanobacterial cells. CRITICAL: The washing step with sterile BG11 broth is necessary to remove metabolic byproducts generated during the growth of cyanobacterial cells. The accumulated byproducts can potentially affect the compressive strength of LBMs. An amount of 15 mL of BG11 broth is sufficient to thoroughly resuspend and wash the harvested cyanobacterial cells. h.Transfer the washed cells (1 mL) to the three Eppendorf tubes (1.5 mL), respectively. Transfer the washed cells (1 mL) to the three Eppendorf tubes (1.5 mL), respectively. i.Centrifuge (20,000 g at 4°C, 2 min) the three Eppendorf tubes and remove cell-free supernatants (900 μL) by the pipette. Centrifuge (20,000 g at 4°C, 2 min) the three Eppendorf tubes and remove cell-free supernatants (900 μL) by the pipette. j.Add methanol (900 μL) into the Eppendorf tube with the remaining cells (100 μL). Add methanol (900 μL) into the Eppendorf tube with the remaining cells (100 μL). k.Place them at 4°C for 30 min under dark conditions. Place them at 4°C for 30 min under dark conditions. l.Centrifuge (at 100 g and 4°C for 1 min) the Eppendorf tubes. Centrifuge (at 100 g and 4°C for 1 min) the Eppendorf tubes. m.Carefully transfer the cell-free supernatants into the new Eppendorf tube (1.5 mL) excepting cell debris. Carefully transfer the cell-free supernatants into the new Eppendorf tube (1.5 mL) excepting cell debris. n.Centrifuge (at 600 g and 4°C for 10 min) the new Eppendorf tubes containing chlorophyll-a. Centrifuge (at 600 g and 4°C for 10 min) the new Eppendorf tubes containing chlorophyll-a. o.Transfer supernatants (200 μL) into the 96 well plates. Transfer supernatants (200 μL) into the 96 well plates. p.Measure chlorophyll-a solutions at OD666 and OD653 using a microplate reader (TECAN, Switzerland). Measure chlorophyll-a solutions at OD666 and OD653 using a microplate reader (TECAN, Switzerland). q.Chlorophyll-a (μg/mL) = (15.65 × OD666 − 7.34 × OD653).1 Chlorophyll-a (μg/mL) = (15.65 × OD666 − 7.34 × OD653).1 r.Inoculate cells (200 μL) with chlorophyll-a concentration (20 μg/mL) fresh BG11 (300 mL) in ten sterile culture flasks (175 cm2). Inoculate cells (200 μL) with chlorophyll-a concentration (20 μg/mL) fresh BG11 (300 mL) in ten sterile culture flasks (175 cm2). s.Incubate the cyanobacterial cells in the culture flasks at 28°C under a light intensity of 25 μmol m−2 s−1 with a 12-h:12-h light: dark photoperiod for 7 days. Incubate the cyanobacterial cells in the culture flasks at 28°C under a light intensity of 25 μmol m−2 s−1 with a 12-h:12-h light: dark photoperiod for 7 days. t.Measure chlorophyll-a concentration as previously described (steps 1 h-q). Measure chlorophyll-a concentration as previously described (steps 1 h-q). u.Adjust the cell density based on chlorophyll-a concentrations to 20 μg/mL in a 50 mL conical tube (50 g). Adjust the cell density based on chlorophyll-a concentrations to 20 μg/mL in a 50 mL conical tube (50 g). Schematic diagram showing the cultivation process of L. boryana GGD (A) Observation of axenic L. boryana GGD in an agar plate using a microscope. (B) Seed culture of a single colony with the BG11 liquid medium for 10 days. (C) Main culture of washed cyanobacterial cells based on chlorophyll-a concentration. Part 2: Procedure for the manufacturing of LBMs using abiotic medium and cyanobacterial cells and their curing conditions Timing: 2 days (for steps 2–4) Timing: 14 days (for step 5) This step describes the manufacturing of LBMs containing cyanobacterial cells. 2.Preparation of gelatin-nutrient solution with cyanobacterial cells.a.Completely dissolve gelatin (25 g) with fresh BG11 liquid (200 g) in a beaker (1 L) using a heating magnetic stirrer at 40°C (Figure 3).b.Place the beaker having the mixtures at room temperature for 10 min until it cools to 30°C.c.Add cyanobacterial cell cultures (chlorophyll-a concentrations, 20 μg/mL) in the conical tube (50 g, from step 1e) into the beaker having gelatin-nutrient solutions, and then vigorously mix them using a magnetic bar (for 1 min). Preparation of gelatin-nutrient solution with cyanobacterial cells.a.Completely dissolve gelatin (25 g) with fresh BG11 liquid (200 g) in a beaker (1 L) using a heating magnetic stirrer at 40°C (Figure 3).b.Place the beaker having the mixtures at room temperature for 10 min until it cools to 30°C.c.Add cyanobacterial cell cultures (chlorophyll-a concentrations, 20 μg/mL) in the conical tube (50 g, from step 1e) into the beaker having gelatin-nutrient solutions, and then vigorously mix them using a magnetic bar (for 1 min). a.Completely dissolve gelatin (25 g) with fresh BG11 liquid (200 g) in a beaker (1 L) using a heating magnetic stirrer at 40°C (Figure 3). Completely dissolve gelatin (25 g) with fresh BG11 liquid (200 g) in a beaker (1 L) using a heating magnetic stirrer at 40°C (Figure 3). b.Place the beaker having the mixtures at room temperature for 10 min until it cools to 30°C. Place the beaker having the mixtures at room temperature for 10 min until it cools to 30°C. c.Add cyanobacterial cell cultures (chlorophyll-a concentrations, 20 μg/mL) in the conical tube (50 g, from step 1e) into the beaker having gelatin-nutrient solutions, and then vigorously mix them using a magnetic bar (for 1 min). Add cyanobacterial cell cultures (chlorophyll-a concentrations, 20 μg/mL) in the conical tube (50 g, from step 1e) into the beaker having gelatin-nutrient solutions, and then vigorously mix them using a magnetic bar (for 1 min). CRITICAL: As the GGD strain exhibits a filamentous morphology, measuring optical density (OD600) with a spectrophotometer is inaccurate for quantification of their cell counting. Therefore, cell density was standardized by extracting chlorophyll-a at a concentration of 20 μg/mL. CRITICAL: Do not mix for more than 1 min to prevent cell damage. Optional: If you construct LBMs without cyanobacterial cells (50 g), you can substitute them with fresh BG11 liquid (50 g). 3.Preparing abiotic substances and biotic medium.a.Put the sterilized standard ISO sand (1,800 g) in a heat-resistant plastic container.CRITICAL: Due to the inconsistent distribution of sand particles affecting the mechanical properties of LBMs, we use standard ISO sand with uniform particle size to achieve reliable mechanical properties of LBMs. Using standard sieves, the particle size of standard ISO sand has the following grading: 0.36–1.7 mm (14.5%); 1.70–1.18 mm (15.8%); 1.188–0.6 mm (23.3%); 0.6–0.3 mm (23.9%); 0.3–0.15 mm (13.6%); <0.15 mm (8.9%).b.Pour the gelatin-nutrient solution and cyanobacterial cells into the plastic container having sand.c.Manually mix the sand with the biotic mixtures thoroughly by hand, wearing nitrile gloves (for 5 min).d.Add CaCl2 (4.04 g) and NaHCO3 (2.31 g) into the plastic container.e.Manually mix the sand with abiotic substances completely by hand, wearing nitrile gloves (for 5 min). The sand mixture is fully saturated in this step. Preparing abiotic substances and biotic medium.a.Put the sterilized standard ISO sand (1,800 g) in a heat-resistant plastic container.CRITICAL: Due to the inconsistent distribution of sand particles affecting the mechanical properties of LBMs, we use standard ISO sand with uniform particle size to achieve reliable mechanical properties of LBMs. Using standard sieves, the particle size of standard ISO sand has the following grading: 0.36–1.7 mm (14.5%); 1.70–1.18 mm (15.8%); 1.188–0.6 mm (23.3%); 0.6–0.3 mm (23.9%); 0.3–0.15 mm (13.6%); <0.15 mm (8.9%).b.Pour the gelatin-nutrient solution and cyanobacterial cells into the plastic container having sand.c.Manually mix the sand with the biotic mixtures thoroughly by hand, wearing nitrile gloves (for 5 min).d.Add CaCl2 (4.04 g) and NaHCO3 (2.31 g) into the plastic container.e.Manually mix the sand with abiotic substances completely by hand, wearing nitrile gloves (for 5 min). The sand mixture is fully saturated in this step. a.Put the sterilized standard ISO sand (1,800 g) in a heat-resistant plastic container.CRITICAL: Due to the inconsistent distribution of sand particles affecting the mechanical properties of LBMs, we use standard ISO sand with uniform particle size to achieve reliable mechanical properties of LBMs. Using standard sieves, the particle size of standard ISO sand has the following grading: 0.36–1.7 mm (14.5%); 1.70–1.18 mm (15.8%); 1.188–0.6 mm (23.3%); 0.6–0.3 mm (23.9%); 0.3–0.15 mm (13.6%); <0.15 mm (8.9%). Put the sterilized standard ISO sand (1,800 g) in a heat-resistant plastic container.CRITICAL: Due to the inconsistent distribution of sand particles affecting the mechanical properties of LBMs, we use standard ISO sand with uniform particle size to achieve reliable mechanical properties of LBMs. Using standard sieves, the particle size of standard ISO sand has the following grading: 0.36–1.7 mm (14.5%); 1.70–1.18 mm (15.8%); 1.188–0.6 mm (23.3%); 0.6–0.3 mm (23.9%); 0.3–0.15 mm (13.6%); <0.15 mm (8.9%). CRITICAL: Due to the inconsistent distribution of sand particles affecting the mechanical properties of LBMs, we use standard ISO sand with uniform particle size to achieve reliable mechanical properties of LBMs. Using standard sieves, the particle size of standard ISO sand has the following grading: 0.36–1.7 mm (14.5%); 1.70–1.18 mm (15.8%); 1.188–0.6 mm (23.3%); 0.6–0.3 mm (23.9%); 0.3–0.15 mm (13.6%); <0.15 mm (8.9%). b.Pour the gelatin-nutrient solution and cyanobacterial cells into the plastic container having sand. Pour the gelatin-nutrient solution and cyanobacterial cells into the plastic container having sand. c.Manually mix the sand with the biotic mixtures thoroughly by hand, wearing nitrile gloves (for 5 min). Manually mix the sand with the biotic mixtures thoroughly by hand, wearing nitrile gloves (for 5 min). d.Add CaCl2 (4.04 g) and NaHCO3 (2.31 g) into the plastic container. Add CaCl2 (4.04 g) and NaHCO3 (2.31 g) into the plastic container. e.Manually mix the sand with abiotic substances completely by hand, wearing nitrile gloves (for 5 min). The sand mixture is fully saturated in this step. Manually mix the sand with abiotic substances completely by hand, wearing nitrile gloves (for 5 min). The sand mixture is fully saturated in this step. 4.Fabrication of LBMs using the acrylic molds.a.Assemble the cubic and cuboid acrylic molds (Figure 1).b.Pour the mixtures evenly into the acrylic mold and perform a 3-layer compaction (Figure 4A).c.Press down the mixture using the lightning rod (30 g) 20 times to compact it (Figure 4B).CRITICAL: The mixtures in the acrylic mold should be evenly tamped across the surface from a height of 10 cm using the lightning rod. The target density of the sand pack is in the range of 20%–30%.d.Press down the upper mixture using the lightning rod (30 g) 20 times to compress it.e.Fill the remaining third of the acrylic mold with the mixtures.f.Discard the mixtures that spill over the edges of the mold using a plastering tool.g.Flatten the mixture on the upper surface of the mold using the plastering tool.h.Cover the top of the acrylic molds using plastic wrap and place it at room temperature for 24 h. Fabrication of LBMs using the acrylic molds.a.Assemble the cubic and cuboid acrylic molds (Figure 1).b.Pour the mixtures evenly into the acrylic mold and perform a 3-layer compaction (Figure 4A).c.Press down the mixture using the lightning rod (30 g) 20 times to compact it (Figure 4B).CRITICAL: The mixtures in the acrylic mold should be evenly tamped across the surface from a height of 10 cm using the lightning rod. The target density of the sand pack is in the range of 20%–30%.d.Press down the upper mixture using the lightning rod (30 g) 20 times to compress it.e.Fill the remaining third of the acrylic mold with the mixtures.f.Discard the mixtures that spill over the edges of the mold using a plastering tool.g.Flatten the mixture on the upper surface of the mold using the plastering tool.h.Cover the top of the acrylic molds using plastic wrap and place it at room temperature for 24 h. a.Assemble the cubic and cuboid acrylic molds (Figure 1). Assemble the cubic and cuboid acrylic molds (Figure 1). b.Pour the mixtures evenly into the acrylic mold and perform a 3-layer compaction (Figure 4A). Pour the mixtures evenly into the acrylic mold and perform a 3-layer compaction (Figure 4A). c.Press down the mixture using the lightning rod (30 g) 20 times to compact it (Figure 4B).CRITICAL: The mixtures in the acrylic mold should be evenly tamped across the surface from a height of 10 cm using the lightning rod. The target density of the sand pack is in the range of 20%–30%. Press down the mixture using the lightning rod (30 g) 20 times to compact it (Figure 4B).CRITICAL: The mixtures in the acrylic mold should be evenly tamped across the surface from a height of 10 cm using the lightning rod. The target density of the sand pack is in the range of 20%–30%. CRITICAL: The mixtures in the acrylic mold should be evenly tamped across the surface from a height of 10 cm using the lightning rod. The target density of the sand pack is in the range of 20%–30%. d.Press down the upper mixture using the lightning rod (30 g) 20 times to compress it. Press down the upper mixture using the lightning rod (30 g) 20 times to compress it. e.Fill the remaining third of the acrylic mold with the mixtures. Fill the remaining third of the acrylic mold with the mixtures. f.Discard the mixtures that spill over the edges of the mold using a plastering tool. Discard the mixtures that spill over the edges of the mold using a plastering tool. g.Flatten the mixture on the upper surface of the mold using the plastering tool. Flatten the mixture on the upper surface of the mold using the plastering tool. h.Cover the top of the acrylic molds using plastic wrap and place it at room temperature for 24 h. Cover the top of the acrylic molds using plastic wrap and place it at room temperature for 24 h. 5.Curing LBMs in a curing chamber.a.Detach the acrylic molds from the side wall first.b.Remove the bottom of the mold (Figure 4C).c.Place the manufactured LBMs in a curing chamber (at 28°C with 80% relative humidity, under a 12-h light/12-h dark period for 14 days), as proliferating cyanobacterial cells can precipitate significant amounts of CaCO₃ under moist conditions. Curing LBMs in a curing chamber.a.Detach the acrylic molds from the side wall first.b.Remove the bottom of the mold (Figure 4C).c.Place the manufactured LBMs in a curing chamber (at 28°C with 80% relative humidity, under a 12-h light/12-h dark period for 14 days), as proliferating cyanobacterial cells can precipitate significant amounts of CaCO₃ under moist conditions. a.Detach the acrylic molds from the side wall first. Detach the acrylic molds from the side wall first. b.Remove the bottom of the mold (Figure 4C). Remove the bottom of the mold (Figure 4C). c.Place the manufactured LBMs in a curing chamber (at 28°C with 80% relative humidity, under a 12-h light/12-h dark period for 14 days), as proliferating cyanobacterial cells can precipitate significant amounts of CaCO₃ under moist conditions. Place the manufactured LBMs in a curing chamber (at 28°C with 80% relative humidity, under a 12-h light/12-h dark period for 14 days), as proliferating cyanobacterial cells can precipitate significant amounts of CaCO₃ under moist conditions. Optional: If you do not have a curing chamber with a humidity controller, you can place a beaker having water inside an incubator to maintain humidity (approximately 80%). CRITICAL: This step is very important to maintain relative humidity for keeping bacterial activity. A reduction in bacterial activity can decrease the amount of precipitated CaCO3, which directly influences the compressive strength of LBMs. Preparation process of mixtures with abiotic and biotic substances Manufacturing of the LBM with an acrylic mold (A) Pouring the gelatin-nutrient mixture with cyanobacterial cells into acrylic molds. (B) Wet mixtures of LBM with sand, abiotic, and biotic substances in an acrylic mold. (C) Solidified and de-molded the LBM after curing at 28°C with 80% humidity for 14 days. Part 3: Procedure for measurement of compressive strengths using curing LBMs Timing: 1 h This step describes the evaluation of compressive strengths using cured LBMs based on the ASTM C346 standard method. 6.Evaluation of cured LBMs using the universal testing machine UTM (INSTRON 4667).a.Place the cured LBMs on the center of the bottom compression plate (Figures 5A and 5B).Note: The cuboid LBMs are divided into halves using a 3-point bending grip, and LBMs are then measured compressive strengths using the UTM (Figures 5C and 5D). The flexural strengths of reference LBMs without cyanobacterial cells and LBMs containing them at 14 curing days were measured at approximately 1.2 ± 0.03 MPa and 1.5 ± 0.09 MPa, respectively.b.Down the top compression plate until it is just about to touch the top surface of the LBMs.c.Apply force to the LBMs using the top compression plate at a pressing speed of 0.02 mm/s (Figure 5B).d.Export data of compressive strengths as an Excel file (.csv). Evaluation of cured LBMs using the universal testing machine UTM (INSTRON 4667).a.Place the cured LBMs on the center of the bottom compression plate (Figures 5A and 5B).Note: The cuboid LBMs are divided into halves using a 3-point bending grip, and LBMs are then measured compressive strengths using the UTM (Figures 5C and 5D). The flexural strengths of reference LBMs without cyanobacterial cells and LBMs containing them at 14 curing days were measured at approximately 1.2 ± 0.03 MPa and 1.5 ± 0.09 MPa, respectively.b.Down the top compression plate until it is just about to touch the top surface of the LBMs.c.Apply force to the LBMs using the top compression plate at a pressing speed of 0.02 mm/s (Figure 5B).d.Export data of compressive strengths as an Excel file (.csv). a.Place the cured LBMs on the center of the bottom compression plate (Figures 5A and 5B).Note: The cuboid LBMs are divided into halves using a 3-point bending grip, and LBMs are then measured compressive strengths using the UTM (Figures 5C and 5D). The flexural strengths of reference LBMs without cyanobacterial cells and LBMs containing them at 14 curing days were measured at approximately 1.2 ± 0.03 MPa and 1.5 ± 0.09 MPa, respectively. Place the cured LBMs on the center of the bottom compression plate (Figures 5A and 5B).Note: The cuboid LBMs are divided into halves using a 3-point bending grip, and LBMs are then measured compressive strengths using the UTM (Figures 5C and 5D). The flexural strengths of reference LBMs without cyanobacterial cells and LBMs containing them at 14 curing days were measured at approximately 1.2 ± 0.03 MPa and 1.5 ± 0.09 MPa, respectively. Note: The cuboid LBMs are divided into halves using a 3-point bending grip, and LBMs are then measured compressive strengths using the UTM (Figures 5C and 5D). The flexural strengths of reference LBMs without cyanobacterial cells and LBMs containing them at 14 curing days were measured at approximately 1.2 ± 0.03 MPa and 1.5 ± 0.09 MPa, respectively. b.Down the top compression plate until it is just about to touch the top surface of the LBMs. Down the top compression plate until it is just about to touch the top surface of the LBMs. c.Apply force to the LBMs using the top compression plate at a pressing speed of 0.02 mm/s (Figure 5B). Apply force to the LBMs using the top compression plate at a pressing speed of 0.02 mm/s (Figure 5B). d.Export data of compressive strengths as an Excel file (.csv). Export data of compressive strengths as an Excel file (.csv). Evaluation of compressive strengths for cubic and cuboid LBMs (A) Compression plates of UTM (INSTRON 4667). (B) Measuring the compressive strength of cubic LBMs using UTM. (C) Division of cuboid LBM into halves using a 3-point bending grip. (D) Measuring the compressive strength of halved cuboid LBMs using UTM. Expected outcomes Compressive strengths of the cubic and cuboid LBMs without cyanobacterial cells were measured in 0.7 MPa ± 0.07 and 1.7 MPa ± 0.07, respectively (Figures 6A and 6C). Compressive strengths of the cubic and cuboid LBMs containing cyanobacterial cells were measured in 1.5 MPa ± 0.07 and 2.8 MPa ± 0.07, respectively (Figures 6B and 6D). To achieve the expected compressive stresses of LBMs harboring the cyanobacterial cells, 10% gelatin and 60 ± 2.3 mg CaCO3 are required at curing 14 days. Although cyanobacterial cell-based LBMs have lower compressive stress compared to cement-based materials, they can serve as alternatives to cementitious materials-based reusable photosynthetic exterior surface structures (e.g., exterior wall sheathing, gazebo roof panels, and patio walls). Expected outcomes of compressive strength for cubic and cuboid LBMs using UTM (A and B) Compressive strength of cubic LBMs with or without cyanobacterial cells, respectively. (C and D) Compressive strength of cuboid LBMs with or without cyanobacterial cells, respectively. Limitations For manufacturing regenerative LBMs using old materials from the parent LBMs Our protocol is suitable for manufacturing engineered LBM with compressive strengths, not for regenerative LBMs using old materials from parent LBMs.1 To utilize the old materials from the parent LBMs, we break them down into particles using a rubber mallet. However, the gelatin within the recycled sand fragments did not fully melt when heated to 40°C during the preparation of the mixture process (step 2a). This resulted in an uneven distribution of gelatin within manufacturing regenerated LBMs, leading to a decrease in their mechanical properties. Repeated experiments are important to overcome this limitation in our mixture process (step 2) using recycled materials from the parent LBMs, ensuring uniform gelatin distribution within the regenerated LBMs. Troubleshooting Problem 1 Low yield of cyanobacterial cells after 7 days. Potential solution Use inoculum with high cell density in fresh BG11 medium. Problem 2 Is it mandatory to use standard ISO sand? Potential solution Standard ISO sand has a uniform particle size distribution and consistent composition, which enhances the reproducibility and reliability of experimental results. If non-standard sand is used for manufacturing LBMs, it is crucial to collect uniform sand particles using standard sieves to ensure reliable compressive strengths of LBMs. Problem 3 The acrylic mold breaks when the mixtures for manufacturing LBMs are placed into the assembled mold. Potential solution Temporarily bind the side of the acrylic mold using tape. Problem 4 When removing acrylic mold, some parts of the LBMs break away. Potential solution Place initially curing LBMs under a low-temperature incubator for 30 min. Problem 5 When removing the acrylic mold, some parts of the LBMs adhere to it and break off. Potential solution Attach Teflon tape to the inside of the acrylic mold to prevent the LBMs from sticking and breaking off. Resource availability Lead contact Further information and requests for resources and reagents should be directed to and will be fulfilled by the lead contact, Woojun Park (wpark@korea.ac.kr). Technical contact Questions about the technical specifics of performing the protocol should be directed to the technical contact, Yongjun Son (2020010812@korea.ac.kr) and Jihyeon Min (m1nzaa@korea.ac.kr). Materials availability This study did not generate new unique reagents. Data and code availability The data supporting the current study are available from the corresponding author on request and are in part published in Son et al. 2024.1 Acknowledgments This work was supported by the National Research Foundation of Korea (NRF-2021R1A2C2009632). The graphical abstract and all figures were produced with biorender.com. Author contributions Y.S., conceptualization, methodology, writing – original draft, data curation, and investigation; J.M., conceptualization, methodology, writing – original draft, data curation, and investigation; J.P. and C.Y., methodology, data curation, conceptualization, and investigation; W.P., conceptualization, methodology, writing – original draft, writing – review and editing, supervision, and project administration. Declaration of interests The authors declare no competing interests. References Associated Data Data Availability Statement The data supporting the current study are available from the corresponding author on request and are in part published in Son et al. 2024.1