Development of a sustainable and disposable modified Bi-CdFe2O4 electrode for electrochemical sensing of lead (II) and Acetaminophen drug molecule Authors: B S Surendra, M Mahadeva Swamy, Bincy Rose Vergis, M Bhaskar, C D Shilpa, Syed Khasim, K Y Chan, H C Ananda Murthy Published: 2024 ABSTRACT AbstractThe study of research proposes a systematic pattern for optimization and fabrication of a sustainable-cost effective electrochemical sensor made by Bi-CdFe2O4 (BCDF) nanoparticle and graphite powder. The structural examinations of synthesized BCDF materials were analyzed by specific spectral techniques viz.; P-XRD, SEM-EDX, TEM, XPS, FT-IR and DRS techniques. The modified sensor electrode offer a significant electrochemical properties that can improve the material selectivity and sensitivity actions measured by Cyclic Voltammetric (CV) and Electrochemical Impedance Spectral (EIS) plots. We demonstrated a developed highly-purity BCDF-graphite paste electrode for sensing actions on Paracetamol and Lead (Pb2+) ions under 0.1 M KCl. The excellent sensing activity towards Lead ions and Paracetamol confirmed by its redox potential peaks at scan rate of 1–5 V/s with maximum sensitivity of -0.61 V and 0.69 V respectively. The excellent photo-dye-degradation action of BCDF (98.2%) than those of host CDF (81.6%) on Rose Bengal (RB) dye was demonstrated. Its kinetic study reveals that this process follows first order kinetics and rate constants of the host (18.1 × 10−3 min−1) and BCDF (39.2 × 10−3 min−1) were measured. Thus, the synthesized BCDF electrode provides a new perception for developing specific nano-sensor towards detection of toxic metals.Keywords: Bi-CDFe2O4 nanoparticles, Green assisted fuel, Electrochemical sensor study, Heavy metal detection, Photocatalytic studiesSubject terms: Chemistry, Nanoscience and technology Introduction Nanotechnology is a part of science encompasses a fabrication and application of materials towards designing and development of various devices by manipulating atoms or molecules at nanoscale range1,2. Various derivatives of organo-phosphorus chemical substances are widely used in industrial manufacture and reaches into the food derivatives and water bodies poses danger to human health. In this regards, the rapid detection of such toxic pollutants becomes increasingly essential for homeland security and health protection3–6. Nanotechnology has emerged as a multi-disciplinary action and is gaining a significant applications in different fields such as optics, sensors, industries, medical-biomedical diagnostics, gas sensing, and energy engineering activities7–10. Among the various kinds of applications, the electrochemical sensor detection of heavy metals and toxic pollutants is considered as the most beneficial for health and environmental issues. Various kinds of toxic metals (Cd, Hg, Cr, etc.) and heavy metals (Arsenic, Thallium, Mercury, Lead etc.) are released into the water-bodies from various sectors, threatening the living organisms10–14. Among these heavy metals, Pb is most the hazardous metal for eco-system because of its properties having higher ionic mobility than those of other organic varieties. According to WHO, the maximum allowable level of Hg2+ ions is 1 µg·L−1 and its exceeded concentrations can affect the environment15–17. Among various heavy metals, the Pb metal is a major public-health concern due to its ubiquitous and impacts on human-beings18. To over come these issues, we focused on detection of heavy metal (Pb2+) using synthesized ferrite nanoparticle as a electrode sensor by electrochemical analytical technique. Nowadays, the electrochemical examination has shown great interest and promising approaches due to simple, high selectivity with sensitivity towards qualitative and quantitative measurements of heavy metals. Various reviews reveals that the modified electrode–electrolyte interface with enhanced selectivity and sensitivity of electrochemical sensor is largely drafting an attention of the scholars for sensing actions of insectisides, pesticides, etc., using glassy carbon electrode19. Based on the unique physico-chemical characteristics (surface area, low energy band gap, etc.), the developed nanoparticles are successfully applied for electrode modification to enhances their electrochemical sensors actions. In this regard, we proposed a modified electrochemical sensors by prepared Bi doped cadmium ferrite nanoparticle to enhances the detection of Hg2+ ions and paracetamol molecules in analyte. Additionally, the nanomaterials can also play a vital role by providing excellent solutions to technological and environmental challenges in the areas of waste water treatment. Currently, large quantities of organic dyes consisting of various toxic chemicals are generated from the textile industries and discharged directly into surrounding water-bodies, causing all aquatic and living organisms. Several researcher and scientists have worked challenging to new nano-catalysts or inorganic materials that may detoxify organic and harmful pollutants in wastewater20,21. Hence, it is necessary to degrade the toxic chemicals using suitable photocatalyst for the reduction of environmental issues.many transition metal-based photocatalysts are non-toxic, and abundantly dispersed in the earth’s crust commonly utilized in photocatalytic mineralization for various organic dyes. Thus, the Bi-CdFe2O4 nanomaterial offers a new possibility towards the step-down of environmental pollution by advanced photocatalytic oxidation activity. The studied research discloses a fabricated Bi-CdFe2O4 nanomaterial has shown excellent activity towards photo-dye-degradation action on RB dye. The outstanding electrochemical studies of BCDF were recorded, which reveals the materials having higher Csp and lesser resistance confirmed by CV and EIS studies. The developed BCDF-graphite electrode has been successfully applied for sensor activity on Paracetamol and Lead (Pb2+) ions in 0.1 M KCl. The excellent sensing actions were measured by its redox potential peaks with scan rate of 1–5 V/s, LOD values and maximum sensitivity. Thus, the synthesized BCDF electrode provides an new perception for developing specific nano-sensor towards detection of toxic metals and photocatalytic applications. Materials and methods Materials The used chemical reagents for experimental synthesis of BCDF nanoparticle are cadmium nitrate (Cd(NO3)2), bismuth nitrate (Bi(NO3)3) and ferric nitrate (Fe(NO3)3) purchased from SD fine-chem Ltd. and were utilized as they received without further purification. Fabrication of BCDF nanoparticle The fabrication of a sustainable-cost effective BCDF nanoparticles under bio-medicinal Tulasi leaf assisted combustion method. The stoichiometric ratios of Bi(NO3)3, Cd(NO3)2 and Fe(NO3)3 are used as initial-precursors for the nano-synthesis. The mixture of optimized green powder (1 g) fuel and starting reagents are situated in a high temperature resistant silica-crucible, which is allowed to attain homogeneity by continuous stirring under a magnetic-stirrer at 600 rpm in presence of 5 ml of double distilled-water. The prepared homogeneous mixture was placed into the muffle furnace combustion assembly maintained at 450 ± 10 °C. The brownish black powder was collected after the combustion process and it was subjected to characterize by various spectral techniques. The step-wise synthesis representation of BCDF nanoparticle was shown in Fig. 1. The schematic representation of synthesized BCDF nanomaterials. Preparation of modified BCDF-graphite electrode The sustainable-cost effective electrochemical examinations of modified BCDF-graphite electrode was analyzed by CV technique. This modification of electrode was achieved by using specific quantity of 0.075 g of BCDF nanoparticle, 0.375 g of graphite powder and 2–3 drops of polytetra-fluoroethylene binder. The above mixture was blended by grinding thoroughly using mortar and pestle for about 30 min. The achieved mixture was placed into the template electrode having copper wire and packed tightly. This modified BCDF-graphite electrode was kept for 1 to 2 h for attaining the electrode stability. This modified electrode offer a significant electrochemical properties that can improve the material selectivity and sensitivity actions. Results and discussions P-XRD investigation Figure 2 shows the Powder X-ray Diffraction (PXRD) patterns of synthesized host and BCDF nanomaterials. The presence of sharp and strong reflection peaks in PXRD patterns reveals the crystalline nature of achieved nanoparticles. The P-XRD spectrum of Bi doped CdFe2O4 nanoparticle shows characteristic diffraction plans at a 2θ angle of 30.06°, 34.19°, 35.35°, 41.17°, 51.07°, 55.02°, 60.24° and 64.33° corresponding to (220), (311), (222), (400), (422), (511), (533) and (622) peaks respectively. This diffraction plans can be indexed as a spinel phase matrix structure and observed planes were good agreement with JCPDS Card No 79-115522,23. The ascertained diffraction plans of prepared bismuth doped cadmium ferrite nanoparticles provides information about its crystal structure and phase composition. However, the doping of bismuth shows a shifting in the positions of P-XRD peaks than those of host-CDF nanoparticle. As a result, the change in lattice parameters are recorded due to the incorporation of bismuth atoms into host-lattice. The spinel ferrite typically made with face-centered cubic oxygen ions and Cd2+ and Fe3+ ions are in tetrahedral and octahedral sites of host-lattice. A small shift of peaks towards a lower angle with increasing the dopant Bi3+ ions in host crystal-lattice is represented in Fig. 3. The doping of bismuth ions may lead to a changes in intensity of P-XRD peaks and causes the variations in degree of crystallinity of the material21–24. PXRD patterns of synthesized host and BCDF nanoparticles from green assisted combustion method. Enlarged portions of XRD pattern of synthesized host and BCDF nanoparticles from green assisted combustion method. Thus, the crystallite sizes of host and BCDF nanoparticles were calculated by the consideration of sharp and high intensity peaks of (311) diffraction planes using Scherrer’s expression [Eq. (1)] and its average crystallite sizes were reported to be 49 –28 nm respectively26–28. where, β is full width half maxima of the peak, D is crystal size, λ is X-ray wavelength. The shifting of diffraction peaks for -BCDF NPs slightly towards a lower 2θ angles at 30.06°, 34.19°, 55.02°, and 64.33° for (220), (311), (422), and (440) diffraction planes are sensed by P-XRD patterns (Fig. 3). The gradual increment of Bi3+ ion concentrations into host-crystal lattice showed an increased intensity of planes and can alter its unit-cell parameters. This modification in unit cell-volume is enlarges the 1-D channel of embedding and shifting of Fermi levels within the host crystal structure. The modification in oxidation states of Bi3+ ion upon incorporation into the host-crystal lattice alters its effective ionic radii i.e., Bi3+ (0.080 nm) to Bi2+ (0.84 Å) and replaced with Cd 2+(0.59 Å). This cognitive process provides valuable insights towards incorporation of bismuth in to the host-CDF matrix and supported to its little reduction in crystallite sizes with enhancing desired applications like conductivity29. SEM-EDX investigations The morphological and elemental examinations of synthesized host and BCDF nanoparticles were characterized by SEM-EDX studies (Fig. 4). The SEM pictures of synthesized BCDF nanoparticle (Fig. 3a) disclosed that particles have a spherical shape and are spongy in nature. Whereas, the host nanoparticles having well agglomerations and irregular particle sizes due to the atoms of nanoparticles are homogeneously distributed on its surface (Fig. 4a&b) disclosed that dispersed on the surface. These SEM micrographs of synthesized nanoparticles shows a characteristics voids and pores due to consequence of combustion method. This SEM spectral studies reveals that the change in morphology due to the presence of Bi ion contents in host nanomaterial. Figure 4(c&d) shows the chemical compositions measurements of synthesized host and BCDF nanomaterials respectively by EDX technique. This spectral data reveals that the absence of Bi ion contents in host nanomaterial and well agreement with the existence of elements such as Bi, Cd, Fe and O in synthesized BCDF nanoparticles. The weight% and atomic percent of elements present in synthesized host and BCDF nanomaterials were recorded as shown in inset Fig. 4c&d. (a&b) SEM images and (c&d) EDX analysis of synthesized host and BCDF nanomaterials. X-ray photoelectron spectroscopy (XPS) analysis XPS analysis is a quantitative surface sensitive technique that measure the electronic structures and chemical states of BCDF nanomaterial. The wide XPS spectrum of synthesized sample distinctly shows its existed elemental composition such as Bi, Cd, O, Fe & C (Fig. 5f) and were well agreed with the EDAX investigation (Fig. 4d). The high-resolution spectral plots of Bi 4f, Cd 3d, O 1s, Fe 2p and C 1s were shown in Fig. 5(a–e) respectively. The XPS peaks ascertained at 156.3 and 163.4 eV were corresponds to the oxidation state of Bi 4f 7/230 (Fig. 5a). The observed two characteristic binding energy peaks at 405.8 and 416.9 eV confirms the bivalent oxidation state of Cd (3d 5/2)31 and its spectrum as shown in Fig. 5b. The difference between binding energy of splitting peaks of Bi and Cd ions was found to be 7.1 eV and 10.8 eV respectively, reveals the nature of oxidation state of Bi3+ and Cd2+ ions. The strong intensity peaks at 535.4 eV is attributed to the presence of oxygen (O 1s) spectrum as displayed in Fig. 5c. The presence of two characteristics peaks at 710.5 and 726.6 eV corresponds to 2p3/2 and 2p1/2 orbits respectively, which shows the nature of oxidation state of Fe3+ (Fig. 5d). Figure 5e shows the C 1s spectrum of prepared sample and its peak observed at 286.6 eV representing the C-C or C-O bonds due to impact of green fuel used synthesis part. Thus, the recorded results support the purity of sample with its elemental measurements and were in concordance with EDX and XRD results. XPS spectral analysis of synthesized BCDF nanoparticle (a) Bi 4f plot; (b) Cd 3d 5/2; (c) O 1s plot; (d) Fe 2p plot; (e) C 1s plot and (f) Wide spectrum of BCDF sample. TEM analysis Further, the structure and morphological investigations of synthesized BCDF nanoparticle were examined by TEM technique (Fig. 6). The TEM images displays a group of particles having tetrahedral and octahedral structures and were observed in low-resolution images at different magnifications as shown in Fig. 6(a&b). The HR-TEM (High-resolution transition electron microscopy) shows the lattice-spacing of BCDF nanoparticle and its interplanar distance was found to be 0.288 nm using adjacent lattice planes (311) of BCDF crystalline material (Fig. 6c). In addition, the SAED (selective area electron diffraction) pattern confirms the poly-crystalline nature of synthesized BCDF nanoparticle (Fig. 6d). (a&b) TEM images; (c) HRTEM images and (d) SAED of pattern of BCDF nanoparticle. FT-IR analysis The nature of bonding and functional groups elucidation of synthesized host and BCDF nanoparticles were investigated by FT-IR spectral studies at 4000 –400 cm−1 (Fig. 7). The broader peak appeared for host and BCDF nanoparticles at 3438 cm−1 attributed to the stretching vibrations of terminal hydroxyl (OH−) groups of adsorbed water molecules at defect sites and its asymmetric stretching modes was observed band at 2899 cm−132–34. The banding characteristics of prepared nanomaterials are measured mainly at finger print region. The sharp bands located between 400 and 1500 cm−1attributed to vibration linkages of metal-oxygen (M-O) bonds in the prepared nanoparticles. The sharp bands located at 419, 563, 861 and 1379 cm−1are ascribed to typical bending modes of Fe-O, Cd-O, Bi-O and Bi-O-Cd linkages respectively35,36. FT-IR examination for synthesized host and BCDF nanoparticles. Diffused Reflectance Spectroscopy (DRS) analysis The optical characteristic of prepared host and BCDF nanomaterials were analyzed through DRS studies at 800 –200 nm (Fig. 8a and b). The energy band gap (Eg) of synthesized host and BCDF nanomaterials were calculated by Kubelka-Munk relation (Eq. 2) with correlation between the diffuse reflectance of BCDF sample (R), the absorption coefficient (K) and the scattering coefficient (S)37; (a & b) Diffused reflection spectral plots and (c &d ) Wood &Tauc’s plots of host and BCDF nanomaterials. Tauc equation used for Eg value and linear absorption coefficient (α) of achieved ferrite nanomaterials by green combustion route, as stated using Eqs. 3 & 4; The energy band gap of prepared host and BCDF nanoparticles were observed by plotting [F(R)hν]2 v/s hν data. The extrapolation of linear fitted areas to [F(R)hν]2=0 shows the Eg value of prepared host and BCDF nanoparticles of 3.3 and 3.0 eV respectively as depicted in Fig. 8c and d. Based on these Eg values, it is necessary to calculate the edge potentials of conduction (ECB) and valance band (EVB) for synthesized host and BCDF nanoparticles using the expressed formula (Eqs. 5 & 6). where, X is electronegativity of prepared host and Bi doped nanocatalysts and E0 is the energy v/s SHE (4.5 eV). The ECB & EVB edge potentials of BCDF nanoparticle were measured to be −4.424 & −1.424 eV respectively. Whereas, ECB and EVB potentials of host nanoparticle were found to be −4.574 & −1.272 eV respectively. This recorded data reveals the photo-response action under light-irradiation with e−-h+ pairs over synthesized host and BCDF nanoparticles and corresponding to its higher photocatalytic measurements. The electronegativity measurements of synthesized host and BCDF nanoparticles were found to be 1.124 & 1.576 respectively, calculated based on its ECB & EVBedge potentials using the following relation-938,39. Surface area analysis of synthesized host and BCDF nanomaterials The physical property measurements of prepared nanoparticles were examined by its specific surface area using BET (Brunauer–Emmett–Teller) technique. BET analysis provides the relevant activities of dissolution and adsorption characteristics of ions or molecules on materials. This technique screening the gas adsorption on external solid surface area and pore area to regulate its total specific surface area. Thus, the pore-volume and specific-surface area of host and BCDF nanomaterials were analyzed from N2 adsorption-desorption isotherms by BET method (Fig. 9a-d). Generally, the synthesized materials from solution combustion method show a higher surface area with smaller particle sizes due to its exothermic characteristics. Hence, the specific-surface area (SBET [m2g−1]) and pore-volume (Dv [cm3g−1]) recorded from Barrett-Joyner-Halenda (BJH) plot for host and BCDF nanomaterials were recorded and mentioned in the Table 1. The BET surface area of BCDF (115.7 m2g−1) is greater than those of host CDF (36.56 m2g−1 ) nanomaterial attributed its excellent photocatalytic applications. (a&c) The N2 adsorption-desorption isotherms and (b&d) Pore volume distribution plot of synthesized BCDF and host CDF nanomaterials. Table 1BET investigation parameters of host and BCDF nanomaterials.SamplesSurface area, SBET [m2g−1]Total pore volume [cm3g−1] 0.7 mol%-BCDF NPs 115.70.246 Host CDF NPs 36.563.142 BET investigation parameters of host and BCDF nanomaterials. Photocatalytic examination Photocatalytic activity has gained great attention due to their potential applications in industrial waste water treatment via oxidation and hydrolysis using heterogeneous photocatalyst under light energy. The synthesized Bi-CdFe2O4 nanoparticle acts as a semiconductor and extensively designed as an excellent heterogeneous photocatalyst due to its lower rate of electron-hole pair recombination and increases the photo-induced chemical reactions for waste water treatment with higher efficiency. The photocatalytic dye-decolouration of RB molecule was used to measure the photocatalytic efficiency of the host and BCDF nanomaterials under UV-Visible light irradiation. The spectral absorbance of light irradiated dye solutions with presence of host and BCDF nanomaterials were measured by using UV-Visible spectroscopy at 540 nm as shown in Fig. 10(a&b) respectively. (a) Spectral absorbance of host CDF; (b) Spectral absorbance of BCDF nanoparticle on RB dye; (c) Percentage decomposition of RB dye; and (d) Stability test. The observed results were recorded by maintaining its specific conditions during the experimental activities performed with 60 ppm of RB dye stock solution and 20 mg of synthesized photocatalysts under light irradiation at 90 min. Therefore, the doped BCDF sample showed an excellent photo-dye-degradation action (98.2%) than those of host CDF (81.6%) on Rose Bengal (RB) dye as shown in Fig. 10(c). In addition, the photocatalytic activities for dye solution were carried out under dark and absence of photocatalysts (photolysis) to measure the stability of RB dye on light energy and its degradation efficiency were found to be 8.2 and 13.3% respectively (Fig. 10c). Further, the recycle stability action of used photocatalyst on RB dye decolouration were measured under similar conditions over 5 cycles as displayed in Fig. 10d. These recorded data reveals that the recycled photocatalyst have no noticeable alteration up-to 5 cycles and confirms its good photo-stability actions on dye degradation. In addition, the measurement of half-time (t1/2) for photo-degradation action of synthesized photocatalysts were examined by plotting (C/C0) v/s time under light energy as depicted in Fig. 11(a&b). The t1/2 of synthesized host and BCDF photocatalysts were found to be 26.5 and 16.2 min respectively. The achieved results reveals the faster dye-degradation action of BCDF photocatalyst than those of host nanomaterial. The efficiency of photocatalytic dye-degradation activity for synthesized samples were outlined by total organic carbon (TOC) investigation. Based on the mineralization index of TOC analysis, the synthesized BCDF photocatalyst showed maximum removal of TOC content under light energy at 90 min as depicted in Fig. 11c. Thus, the synthesized BCDF photocatalyst played excellent role in TOC reduction and reveals its industrial applications to prevent secondary pollution. The kinetics theory for synthesized host and BCDF photocatalysts on dye degradation was discussed as depicted in Fig. 11d. The kinetics characteristics were calculated by ln(C/C0) = − kt. Here, k is the rate constant; C & C0 are the dye concentration and its initial concentration, respectively. The measured rate constants of synthesized host and BCDF photocatalysts on RB dye were recorded and it was shown in Table 2. (a&b) Half time for dye degradation investigation; (c) TOC plot and (d) Kinetics studies of synthesized nanomaterials. Table 2The kinetic rate constants parameters of synthesized host and BCDF photocatalysts.Sl. NoPhotocatalystsPercentage DegradationK x 10−3 (min−1)Slope1Host CDF NPs81. 618.10.0078532BCDF (0.7 M ) NPs98.239.240.016657 The kinetic rate constants parameters of synthesized host and BCDF photocatalysts. The potential chemical redox reactions involved in photo-dye-decomposition under UV-Visible-light irradiation. The prepared BCF photocatalyst should have high negative potential (CB) value than those of redox potential of LUMO in BCF-photocatalyst-acceptor part. Similarly, the higher positive potential (VB) value than those of reduction potential of HOMO in BCF-photocatalyst-donor part. Thus, it regulate that the higher energy band gap of photocatalyst has lower photo-dye degradation activity this physico-chemical process represented as inverted region effect40. The BCF-photocatalyst displays an efficient photocatalytic action on RB dye due to its composition consisting chromophore groups and azo linkages (-N = N-), which exhibit a prominent wavelength-peak at 561 nm due to their n → π* transition. The BCF nanocatalyst absorbs energy from light radiation and produces several e−/h+ as expressed in Eqs. (8 & 9). These resulted charges are directly responsible for the creation of several free active radicals such as OH•, and O2•− groups by gaining holes and electrons (Eqs. 10 & 11). Hence, these radicals are identified as major contributors to the degradation process in the textile dyes (Fig. 12)41–44. The mechanism of photocatalytic activity of BCDF nanomaterial on RB dye degradation. Electrochemical examination The interfacial electro-catalytic and electron transfer characteristics of modified graphite-based nano-electrodes were ascertained by Cyclic voltammetry (CV) and Electrochemical impedance spectroscopy (EIS) techniques45,46. Figures 13a and 14a displays the CV plots of host CDF and BCDF nanoparticles respectively carried out at 0.01–0.05 V/s scan rates at 0.1 M KCl (pH = 5.6) under a 3-electrode system. During oxidation and reduction analyzed by CV studies, the changes in pH of the electrolyte takes places and it is controlled by using common neutralizing agent NaOH/KOH base. For every measurements, stir the electrolyte thoroughly and check the pH repeatedly until the attaining of desired pH. This examination is a evident of variations in cathodic and anodic peak currents observed at potential window ranges from + 0.6 to -0.8 V attributed to its reversibility of redox reaction. In this regard, the enhanced regression data (R2) of BCDF nanoparticle was recorded to be 0.96785 in contrast to R2 (0.8336) data of host nanoparticle as shown in Figs. 13b and 14b respectively, reveals the greater reversible and diffusion-controlled of electrodes45. The steady-current outcomes for host-CDF and BCDF nanoparticles were recorded as represented in the Tables 3 and 4respectively. Thus, Randles-Sevecik equation (Eq. 12) is used to calculate the peak current from redox potential differences of synthesized samples. The low potential difference of BCDF nanoparticle was observed (0.34 V) than host nanoparticle (0.65 V), corresponding to its high reversibility of reaction47–51. (a) CV plot; (b) Square root of scan rate and (c) EIS-Nyquist curve of host-CDF nanoparticle at different scan rate in 0.1 M KCl. (a) CV plot; (b) Square root of scan rate and (c) EIS-Nyquist curve of BCDF nanoparticle at different scan rate in 0.1 M KCl. Table 3Reversibility of redox reaction and diffusion coefficient of host-CDF nanoparticle.Scan rates (mV/s)E oxd. x10-4E red. x10-4Reversibility (ER) x10-3Diffusion co-efficient (Dx10-6)101.182−4.325.53.245201.332−4.996.32301.513−5.737.243401.665−6.027.685501.995−8.0210.01 Reversibility of redox reaction and diffusion coefficient of host-CDF nanoparticle. Table 4Reversibility of redox reaction and diffusion coefficient of BCDF nanoparticle.Scan rates (mV/s)E oxd. x10-4E red. x10-5Reversibility (ER) x10-3Diffusion co-efficient (Dx10-7)100.716−1.552.2664.562200.935−2.653.585301.18−4.515.69402.17−5.497.66503.03−6.019.04 Reversibility of redox reaction and diffusion coefficient of BCDF nanoparticle. Figures 13c and 14c shows the EIS-Nyquist curves of host-CDF and BCDF nanoparticles respectively measured at 10–4350 Hz. In this plots, the diameter of semicircle arc for host-CDF and BCDF nanoparticles were found to be 277 and 74 Ω respectively, corresponding to its nature of capacitance and charge transfer resistance. Thus, the lower semicircle arc of BCDF nanoparticles reveals its higher charge transfer resistance and capacitance than those of host-CDF. However, straight line apt towards the Y-axis reveals the fast-diffusion of chemical substances in prepared electrodes. Hence, these rapid conductivity and diffusion of ions plays a vital role in making modified electrodes as excellent sensor actions52–55. Electrochemical sensor studies of BDCF nanoparticle Figure 15a shows the electrochemical CV plot of BDCF nanoparticle for lead (Pb2+) sensing was carried out with concentration of 1 mmol/L to 5 mmol/L at 0.03 V/s in 0.1 M KCl. The sensing performance of BDCF nanoparticle for Pb2+ was observed by its increased current (+ 5.65 × 10−4 A/cm2 at 5 mM) in between the potential window of −0.8 to + 0.8 V. The good sensing action of BDCF nanoparticle on Pb2+ was confirmed by the appearance of high current densities in oxidation potential peak at −0.61 V and reduction potential peaks at + 0.27, + 0.02 & −0.625 V as shown in Fig. 15c. Hence, the achieved results of prepared BCDF sample shows a sensitivity and R2 values are found to be + 5.65 × 10−4 A/cm2 (mmol/L) and 0.9412 respectively (Fig. 15b). The sensing action can be explained based on the reduction reaction of Pb2+ to Pb as shown in (Fig. 15d). The LOD (limit of detection) and LOQ (limit of quantification) of Lead ions were measured as mentioned in the Table 5. The reported results reveal an excellent sensing activity of modified electrode towards Lead ions at low concentrations. Thus, LOD and LOQ of the electrode was found to be 1.307 mM & 3.458 mM respectively at maximum sensitivity of −0.61 V and 2.694 mM & 8.981 mM at maximum sensitivity of 0.02 V. The LOD and LOQ are measured from the calibration line by using the following formula; LOD = 3s/m and LOQ = 10s/m. Where s; indicating the standard deviation of the intercept and m represent the slope of calibration plot4. (a) The electrochemical CV plot of BDCF nanoparticle for lead (Pb2+) sensing, (b) Square root of scan rate, (c) CV plot of with (4mM) and without sensor; and (d) Sensing mechanism of Pb2+ ions. Table 5The LOD and LOQ determinations for Pb and PA ions.SampleStandard deviation x10-5Slope x10-5LOD (mM)LOQ (mM)BCDF NPs-PA (Red)3.11869.016451.037453.458BCDF NPs-PA (Oxid)1.764380.9050.58691.9656BCDF NPs-Pb (Red)3.932098.5211.30764.358BCDF NPs-Pb (Oxid)8.097086.582.6948.694 The LOD and LOQ determinations for Pb and PA ions. (a) The reduction plot of BDCF nanoparticle for Pb sensing between +0.14 & −0.09 V, (b) Plot of increasing addition of Pb v/s current, (c) Oxidation plot for PA sensing between −0.4 & −0.75 V, and (d) Plot of increasing addition of Pb v/s current. The reduction peak plot for Pb sensing between + 0.14 & -0.09 V and R2 values from increasing addition of Pb v/s current of prepared BDCF nanoparticles were examined for its sensing actions analysis as shown in Fig. 17(a & b). Likewise, for oxidation peak plot of Pb sensing between − 0.4 & −0.75 V with R2 values were measured Fig. 17(c & d). Thus, the recorded current densities reports reveals an good sensing action of BCDF nanoparticle on Pb2+. (a) The electrochemical CV plot of BDCF nanoparticle for lead (PA) sensing, (b) Square root of scan rate, (c) CV plot of with (4mM) and without sensor; and (d) Sensing mechanism of PAions. Similarly, the electrochemical CV plot of BDCF nanoparticle for PA sensing was carried out with concentration of 1 mmol/L to 5 mmol/L at 0.03 V/s in 0.1 M KCl (Fig. 18a). The sensing performance of PA was observed by its decreased current (+ 1.61.65 × 10−4 to 4.38 × 10−4 A/cm2 at 5 mM) in between the potential window of −0.8 to + 0.8 V. The good sensing action of BDCF nanoparticle on PA was confirmed by the appearance of high current densities in reduction potential peak at + 0.69, + 0.27, and 0.27 V and oxidation potential peaks at -0.63 V as shown in Fig. 18c. Hence, the achieved results of prepared BCDF sample shows a sensitivity and R2 values are found to be + 5.65 × 10−4 A/cm2 (mmol/L) and 0.9412 respectively (Fig. 18b). The sensing action can be explained based on the redox reactions of PA to PA ions and vice versa as shown in Fig. 18(d). The LOD and LOQ of PA were measured as mentioned in the Table 5. The reported results reveal an excellent sensing activity of modified electrode towards Lead ions at low concentrations. Thus, LOD of the electrode was found to be PARed.1.57 mM & PAOxd.-6.44 mM with highest sensitivity at 0.69 V. (a) The oxidation plot of BDCF nanoparticle for PA sensing between − 0.35 & −0.55 V, (b) Plot of increasing addition of PA v/s current, (c) Reduction plot for PA sensing between − 0.80 & +0.60 V, and (d) Plot of increasing addition of PA v/s current. Conclusions A modified nano-based electrode study offered a useful process for devising sustainable-cost effective electrochemical sensor by BCDF nanoparticle. The selectivity and sensitivity action of prepared material was examined on heavy metal -Pb(II) and Acetaminophen drug molecule under 0.1 M KCl. The increasing concentration (1 mmol/L to 5 mmol/L at 0.03 V/s) of positively charged Pb(II) and paracetamol in addition to modified nano-electrode shows good adsorption and excellent redox reaction in conductive analyte, resulted as higher CV signals. Thus, the excellent sensing activity was recorded towards Lead ions confirmed by its redox potential peaks with scan rate of 1–5 mM, LOD of PbRed.1.53 mM, PbOxd.-4.1 mM, and maximum sensitivity of -0.61 V. Similarly, Paracetamol sensing actions were recorded by LOD of PARed.1.57 mM PAOxd.-6.44 mM with highest sensitivity at 0.69 V. The Eg value of prepared host and BCDF nanoparticles were found to be 3.3 and 3.0 eV respectively. The decreased energy band gap of BCDF nanoparticle showed enhanced photo-dye-degradation action (98.2%) than those of host CDF (81.6%) for RB degradation under light irradiation at 90 min. The t1/2 of synthesized host and BCDF photocatalysts were found to be 26.5 and 16.2 min respectively reveals the faster dye-degradation action of BCDF photocatalyst. Finally, the synthesized BCDF electrode provides an new perception for developing specific nano-sensor for detection of heavy metal/toxic molecules. Author contributions B.S.S. Supervised, Designed, Investigated, analyzed data and wrote the manuscript. H.N.S and M.M.S did Formal analysis. B.R.V. and C.D.S. did Visualization and Methodology. M.B, K.Y.C, H.C.A.M. involved in Final editing and Review and conducted formal analysis. Funding No funding received. Data availability The data available on request from the corresponding author (surendramysore2010@gmail.com). Declarations Competing interests The authors declare no competing interests. Ethical approval Not Applicable. Footnotes Publisher’s note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations. Contributor Information B S Surendra, Email: surendramysore2010@gmail.com. K. Y. Chan, Email: kychan@mmu.edu.my References Associated Data Data Availability Statement The data available on request from the corresponding author (surendramysore2010@gmail.com).