The hydrogen puzzle in rock-enhanced biochar: Pyrogenic coating, mineral redox and pore accessibility Johannes Meyer zu Drewer, Tobias Bromm, Thomas D Bucheli, Pellegrino Conte, José María de la Rosa, Harald Fitzek, Amin Ghafarpour, Bruno Glaser ABSTRACT Rock-enhanced (RE-)biochars, produced by co-pyrolysis of silicate rock powder with biomass, were proposed to combine pyrogenic carbon capture and storage (PyCCS) with enhanced rock weathering (ERW) as complementary carbon dioxide removal approaches. Catalytic effects of rock-derived AAEM on pyrolysis and carbon speciation were anticipated. Here we produced six RE-biochars (10–90% rock content) by co-pyrolysis of basanite rock powder with wood at contrasting highest treatment temperatures of 450 °C and 750 °C. To provide an in-depth physico-chemical characterization of the RE-biochars, focusing on the biochar-mineral interface region, analytical methods including random reflectance, fast field cycling proton nuclear magnetic resonance relaxometry and electron energy loss spectroscopy were employed. While most treatments had limited effect on the biochar carbon yield (yc) and aromaticity of the pyrogenic carbon, RE-biochar produced at 750 °C and containing 90% rock showed an increased hydrogen to carbon molar ratio (H:Corg), which we partly explained by i) contribution of geogenic hydrogen, ii) physical adsorption of hydrogen to minerals and iii) pyrogenic coating of rock particles with secondary char containing aliphatic- and carboxylic moieties. Still, we cannot fully identify the reasons for increased hydrogen content with constant aromaticity. A decreased reflectance (Ro) and thermal stability (BC1000C) for RE-biochars with 90% rock content, despite similar aromaticity as quantified by hydropyrolysis, highlight the limitations of analytical methods developed for carbonaceous materials in the assessment of high ash biochars. Co-pyrolysis can reduce metal oxides, such as hematite (Fe-III) to magnetite, producing (potentially) reactive metals species and can accumulate geogenic potassium (K) at micron scale at rock particle surfaces. This study provides evidence that co-pyrolysis of biomass and basanite does not increase yc but alters the mineral speciation and elemental distribution at the surface of rock particles. These findings may be further exploited in the design of functionalized RE-biochars and in ERW research. 1. Introduction The co-pyrolysis of biomass with exogeneous minerals was suggested to design functional biochars [ 1 , 2 ]. The presence of mineral matter in biomass pyrolysis impacts the relative yields of gaseous, liquid, and solid pyrolysis products as well as their carbon speciation. Those effects were shown for minerals inherently present in biomass [ 3 ] and for additives like salts, or wood ash [ 4 – 6 ]. The deliberate addition of mineral matter to the feedstock before pyrolysis is referred to as co-pyrolysis. Potassium salts can, e.g., improve phosphorus availability in sewage sludge char by the formation of soluble potassium hydrogen phosphate during pyrolysis [ 7 ]. Silica, iron salts and other metals were applied to improve the capacity of biochar to sorb organic micropollutants [ 8 ]. Underlying mechanisms may include alterations to biochar carbon speciation and porosity, but also the formation of specific mineral surfaces during pyrolysis, e.g., the reductive formation of magnetite, a mixed valence iron mineral from the Fe(III) mineral siderite [ 9 ] or the formation of Fe(0) from Fe(III)-hydroxide [ 10 ]. Mineral additives can also increase the biochar carbon yield (y c ), i.e., the fraction of biomass carbon converted to solid state pyrogenic carbon (PyC) during (co-)pyrolysis [ 11 – 13 ]. This was demonstrated for biomass co-pyrolyzed with wood-ash [ 6 ] or potassium acetate [ 5 ]. Improved mass conversion is mediated by catalytic effects [ 12 ], the formation of organo-metallic bonds [ 14 ], or the (partial) encapsulation of biomass [ 8 , 15 ]. Alkali and alkaline earth metals (AAEM) contained in mineral additives appear to be most relevant for the catalytic reduction of activation energy for biomass decomposition and the promotion of C–C cross-linkage formation, which together increases secondary char formation [ 6 , 16 ]. Silicate rock powder, as employed for enhanced rock weathering (ERW) [ 17 – 19 ] and for soil remineralization [ 20 – 22 ], was suggested as an abundant mineral additive to produce rock-enhanced (RE-)biochar [ 23 – 25 ]. Meyer zu Drewer et al. [ 24 ] showed that rock powder particles received a pyrogenic coating during co-pyrolysis, i.e., secondary char condensates on their surfaces, which could enhance y c by increasing secondary char formation. However, y c and aromaticity remained unaltered despite rock powder addition. Alkali and alkaline earth metals, when embedded in a (crystalline) silicate rock matrix, seem to remain, opposite to the above, largely unexposed and non-reactive at highest treatment temperatures (HTT) of 650 °C. Since rock powder has a significantly higher thermal conductivity than biomass, it has been suggested that this leads to a higher pyrolysis intensity (i.e., higher heating rate and thus in longer exposure to the HTT) within biomass-rock powder pellets compared to pure biomass [ 22 ]. In the present study, we investigate how co-pyrolysis is altering the physico-chemical properties of RE-biochar, compared to pure biochar. We expand previous characterisations of RE-biochars [ 24 , 25 ] with a novel set of samples and a focus on microsites at the biochar-mineral interface, where a distinct PyC and mineral speciation may form during pyrolysis. Therefore, we produced six RE-biochars by co-pyrolysis of softwood with basanite rock powder at 450 °C and 750 °C. The RE-biochars contained 10 wt% (9:1), 50 wt% (1:1), or 90 wt% (1:9) basanite rock powder alongside two pure softwood biochars (BC450, BC750). Using random reflectance (Ro), hydropyrolysis (HyPy), benzene polycarboxylic acids (BPCA) molecular marker method, fast field cycling relaxometry proton nuclear magnetic resonance spectroscopy (FFC 1 H-NMR) and scanning transmission electron microscopy coupled to electron energy loss spectroscopy (STEM-EELS) and other analytical methods, we characterized the PyC speciation and discussed potential mechanisms affecting the latter. Both weathering and alkalinity production as well as the effect on plant growth of the (RE-)biochars characterized here, were investigated in Meyer zu Drewer et al. 2026 [ 26 ]. 2. Results and discussion 2.1. Increased H:C org ratio despite similar aromaticity: Where does the hydrogen come from? Biochars were produced from pelleted, low-ash wood shavings (biomass composition S1 Table ) at 450 °C and 750 °C in a continuously operated auger reactor [ 27 ]. These showed well-expected properties, mass yield (y m ), and y c as shown in Table 1 [ 28 – 30 ]. Based on the y m of the pure biochars, we mixed basanite rock powder (elemental and mineral composition, S2 Table ) to the wood shavings prior to pelleting and pyrolysis to achieve the desired rock powder content in the RE-biochar. 10.1371/journal.pone.0355781.t001 Table 1 Basic physico-chemical properties of biochar and rock-enhanced biochar (BC) produced at 450 °C (450) or 750 °C (750), containing 0 (-), 10% (9:1), 50% (1:1) or 90% (1:9) basanite rock powder. Data on main- and trace element content are presented in S7 Table and basic properties of basanite in S2 Table ). BC450 BC450–9:1 BC450–1:1 BC450–1:9 BC750 BC750–9:1 BC750–1:1 BC750–1:9 Mass yield (y m in%) 1 25.6 ± 0.5 28.0 ± 0.3 40.5 ± 1.2 72.7 18.9 ± 0.7 24.7 ± 0.1 33.4 ± 0.2 66.4 Carbon yield (y c in %) 1 42.9 ± 0.9 43.7 ± 0.4 40.3 ± 1.2 46.6 35.2 ± 1.2 41.3 ± 0.2 35.5 ± 0.2 38.3 Rock content (%) 0 5.7 50.2 89.1 0 8.3 49.9 89.1 Biogenic content (%) 100 94.3 49.8 10.9 100 91.7 50.1 10.9 Total ash (%) 1.9 7.5 51.2 89.3 3.0 11.0 51.3 89.4 Biogenic ash (%) 1.9 1.8 1.0 0.2 3.0 2.7 1.4 0.3 Carbon (C, %) 85.0 76.7 41.5 9.3 94.3 83.6 46.2 9.7 Organic C (C org ,%) 84.8 76.7 41.5 9.3 93.9 83.2 45.8 9.6 C org_daf (% of C org ) 86.4 87.1 86.1 86.1 96.5 95.0 96.0 98.0 C vol.HAWK (mg g -1 C org ) 2 10.9 11.7 10.7 12.9 0.3 0.4 0.7 3.3 BC HyPy (% of C org ) 3 56.4 58.4 49.5 42.7 97.3 95.6 97.4 97.2 TIC (%) 4 0.2 < 0.1 < 0.1 < 0.1 0.4 0.4 0.4 0.1 Hydrogen (H, %) 3 2.9 1.7 0.4 1.3 0.8 0.5 0.7 Nitrogen (%) 0.29 0.06 < 0.05 < 0.05 0.33 0.41 0.15 < 0.05 Sulfur (%) < 0.03 < 0.03 < 0.03 < 0.03 < 0.03 < 0.03 < 0.03 < 0.03 Oxygen (%) 9.8 8.4 5 1.2 1.3 2.8 0.9 2.9 Å) in 2:1-layer silicates are relevant for H 2 adsorption [ 43 – 45 , 48 ]. Catalytic metals can further enable hydrogen spillover to surfaces that otherwise do not bind H under identical conditions [ 49 ]. Lastly, H (respectively H 2 O) can also be structurally incorporated in nominally anhydrous minerals and isomorphically substitute geogenic metal ions such as Mg 2+ . This was demonstrated for olivine under extremely high pressure and temperature regimes. At 1 atm, this process is much more limited and likely restricted to surface sites. Natural, nominally anhydrous olivine contains < 0.05 mol H kg -1 [ 50 , 51 ]. Sundvall & Skogby (2011) [ 52 ] investigated the protonation of pyroxene under varying conditions. Under 1 atm up to 700 °C they found that most pyroxenes lost H while hydration was only observed for pyroxenes rich in iron (Fe). They explained this observation by a surface redox reaction. Olivine and pyroxene are both present in the basanite employed here, which also contains 7.8% Fe ( S2 Table ). We used X-ray diffraction (XRD) to detect possible changes in the mineralogy of basanite thermally treated in the absence of biomass and basanite co-pyrolyzed to form RE-biochars (9:1). The heating of pure rock powder had no effect on the speciation of silicate minerals (R450 and R750 in S2 Table ). The content of all silicate minerals in the 450 °C RE-biochars was in good agreement with expected, calculated concentrations. In RE-biochars produced at 750 °C, the content of all silicate minerals fell below the expected values, while the amorphous fraction increased ( Table 2 ); for example, the detected content of the potassium (K)-bearing mineral leucite was 50% below the expected value. We assume that X-ray diffraction was not affected by the presence of PyC as illustrated by the successful detection of calcite in pure BC750, despite a total inorganic carbon (TIC) content of < 1%. In summary, the assessment of bulk mineralogy confirmed changes induced by co-pyrolysis that were absent in thermal treatment without biomass, but did not directly prove H uptake. Further research should employ X-ray photoelectron spectroscopy (XPS) to investigate changes in binding energy in surface minerals only. 10.1371/journal.pone.0355781.t002 Table 2 Concentration of mineral species in pristine basanite rock powder (R), pure biochar (BC450, BC750) and selected rock-enhanced (RE-) biochars produced at 450 °C containing 10% rock (RE-BC450-9:1) and produced at 750 °C containing 10% rock (RE-BC750-9:1) based on X-ray diffraction (XRD) measurements. The data is presented in mass-%. Mineral Group Mineral Formula R BC450 BC450–9:1 BC750 BC750–9:1 expected* measured expected* measured Quartz SiO ₂ 0.5 <0.1 0 0.1 <0.1 0 3 and platykurtic <3) and Skewness (Gaussian distribution = 0, right skewed >0 and left skewed <0). 3. Conclusions Co-pyrolysis of biomass with silicate rock powder was proposed as an avenue to synergistically combine PyCCS- and ERW-based carbon dioxide removal in one composite material. Geogenic metals (incl. AAEM) can catalyze biomass pyrolysis and potentially engage in the formation of organo-metallic bonds (e.g., Fe-C). However, the impact of AAEM in our study is limited, as the y c and PyC speciation (aromaticity as indicated by HyPy and BPCA-marker assessment) of RE-biochars was not altered compared to pure biochar. This suggests that up to a HTT of at least 750 °C, AAEM embedded in crystalline structures of basanite rock remain largely inactive as pyrolysis catalysts. The identification of organo-metallic bonds would require dedicated spectroscopic evidence, which was beyond the scope of this study and thus was neither confirmed nor refuted. Rock-enhancement does not impact the environmental persistence of RE-biochars – as indicated by BC HyPy content and BPCA markers. It was demonstrated that H:C org molar ratio of RE-biochar must be interpreted with caution. The inorganic phase can both contribute geogenic H and is able to sorb biogenic H. This is distorting the bulk H:C org ratio of the RE-biochar, which can no longer be interpreted independent of the inorganic phase. Also, other analytical approaches like random reflectance and thermal analysis may be compromised by matrix-effects where rock powder was added at high rates. Matrix-effects require urgent consideration during experimental design and data interpretation, not just for RE-biochar, but also for other high ash biochars. When no comparable low-ash biochar is available as a reference, as it is the case, e.g., for sewage sludge, hydrofluoric acid treatment should be tested to remove mineral components prior to elemental analysis. Mineral surfaces exposed to syngas experience several alterations during co-pyrolysis. These include the reduction of iron-oxides, the locally discrete accumulation of K, and the pyrogenic coating with conductive secondary char. These observations provide first evidence that silicate rock particles can be modified by co-pyrolysis with biomass. These alterations may be exploited in a context of ERW (faster weathering, cf. [ 26 ]), agriculture (increased availability of nutrients, e.g., K-phosphates) and functionalized biochars (improved sorbents) – however all three fields require further research, which also needs to expand on how rock additions impact the agronomic performance of biochar. 4. Materials and methods 4.1. Biomass preparation and pyrolysis Spruce wood shavings ( Picea abies L.) were sourced from Allspan German Horse GmbH, Karlsruhe, Germany (50.7% C, 0.5% ash; S1 Table). Basanite rock powder (“Eifelgold”; particle size range 0–250 µm) was obtained from Provinzial-Basalt- u. Lavawerke, Sinzig, Germany and characterized by X-ray diffraction, X-ray fluorescence, laser granulometry and extraction in ultra-pure water as described elsewhere [ 24 ]. The basanite’s SSA was measured as described in section 4.2. Both, pure biomass and homogenized mixtures of biomass with fine rock powder were pelleted at 6 mm without additional binders using a WK230 pellet press (Evertec, Dieburg, Germany). Afterwards, the pellets were dried (12 h at 60 °C), and fine material (< 6 mm) was removed by sieving. The required feedstock mixing ratios to obtain RE-biochars with nominal 10%, 50% or 90% rock content, were calculated based on mass-yield (y m ) measured during production of pure biochar at 450 °C (BC450; y m = 25.9%) and at 750 °C (BC750; y m = 18.9%). The mass of the basanite was constant during pyrolysis, which was also verified by thermo-gravimetric analysis (TGA) of pure basanite. As some rock powder might got lost during pelleting and sieving, the actual biogenic (f bio ) and rock mass fraction (f rock ) of the feedstock was re-calculated following equation 1 and 2 ( Table 3 ). 10.1371/journal.pone.0355781.t003 Table 3 Composition of feedstock to produce rock-enhanced biochar (BC) at 450 °C (450) or 750 °C (750), containing 10% (9:1), 50% (1:1) or 90% (1:9) basanite rock powder after pyrolysis. # Sample ID Biogenic fraction (%) Rockfraction (%) C org (%) Biogenic ash(%) Total ash(%) 1 BC450 100 0 50.6 0.4 0.4 2 BC450–9:1 97.9 2.1 49.5 0.4 2.5 3 BC450–1:1 75.9 24.1 39.2 0.3 24.4 4 BC450–1:9 28.8 71.2 15.0 0.1 71.3 5 BC750 100 0 50.6 0.4 0.4 6 BC750–9:1 98.6 1.40 50.4 0.4 1.8 7 BC750–1:1 84.0 16.0 42.0 0.3 16.3 8 BC750–1:9 39.7 60.3 18.1 0.1 60.4 f r o c k ( % ) = A s h ( % ) − C o r g ( % ) * r (1) f b i o ( % ) = 1 0 0 − f r o c k ( % ) (2) With ash (%) being the ash content and C org (%) the organic carbon content of the feedstock mix. The factor r describes the ratio of C org to ash in the pure biomass (s1). The same procedure was applied to calculate f bio and f rock for RE-biochars, assuming no mass loss of rock powder during pyrolysis and no impact of rock powder on biochar dry and ash free (daf) yield. Feedstock transport-rates (t f in g min -1 ) through the non-heated pyrolysis reactor were determined for each treatment by measuring material output in 10 min intervals ( n = 6). In the same manner, biochar transport-rates (t b in g min -1 ) through the heated pyrolysis reactor were determined in 30 min intervals ( n = 3). Pyrolysis was performed at 450 °C and 750 °C, respectively, with a residence time of 15 min using a PYREKA research pyrolysis unit equipped with a continuously operating auger reactor (PYREG GmbH, Dörth, Germany) under Nitrogen flow of 2 L min -1 [ 24 , 27 ]. The PYREKA operated in one continuous process per treatment. The ratio of feedstock to biochar output during the first hour (equivalent to four reactor residence times) and after the feeder ran empty, was excluded from transport rate calculations and therefore from calculation of y m and y c . The biochar mass yield was calculated as follows: y m ( % ) = t b t f * 1 0 0 (3) With y m being the pyrolysis mass yield as % of dry weight feedstock converted to dry weight biochar, t f the mean transport-rate of the feedstock (g min -1 ) and t b the mean (RE-)biochar transport-rate (g min -1 ). Exceptions were BC450–1:9 and BC750–1:9, here, due to the limited material volume, no transport-rate was determined but the total mass before and after pyrolysis measured. Further, the coefficient of variation (%CV) in t b was calculated as a proxy for the variability of the continuous production process and resulting y c . The y c was calculated as follows: y c ( % ) = y m * C o r g ( B C ) C o r g ( f ) (4) With y m being the mass yield of pyrolysis process (%), C org(f) the C org content of the feedstock and C org(BC) the C org content of the produced (RE-)biochar. The (RE-)biochar production during the ramp-up/down time as described above was discarded not to be included in any analytical sample. The remaining production was pooled and thoroughly mixed. While many of the pellets were broken into smaller fragments by the moving parts in the reactor, ten intact pellets were randomly selected and set aside for microscopy. The remaining (RE-)biochar was milled in an impact mill with 2 mm sieve. Due to the brittle nature of the material, a fine powder was produced this way. The particle size distribution of comparable biochars after milling was quantified by laser granulometry (Sympatec Helos KFMagic, Sympatec GmbH, Clausthal-Zellerfeld, Germany) and is typically one order of magnitude smaller than the sieve size [ 27 ] (> 90 mass-% at < 200 µm for a 2 mm sieve). To supply larger quantities of (RE-)biochar to other follow-up experiments (not subject to this publication), a second batch of all treatments was produced. To this end, the same raw materials were used ( S3 Table ), pelleted by Nature Power Pellets (Wolferstadt, Germany) and pyrolyzed on the PYREKA under same process conditions as described above. The pellets produced by Nature Power Pellets had the same dimensions but a higher density. Biochar and RE-biochars from the first production batch were subject to all analytics described in section 4.2 while materials from the second batch were only subject to basic characterization ( S4 Table ) with additional calculation of y m , y c , f bio and f rock . 4.2 Biochar analysis All (RE-)biochars were analyzed following the analytical guidelines of the European Biochar Certificate [ 78 ] by Eurofins Umwelt-Ost GmbH (Bobritzsch-Hilbersdorf, Germany). The C org content of the daf biochar (C org_daf ) was calculated as follows C o r g d a f ( % ) = C o r g ( % ) 1 0 0 % − Ash ( % ) * 1 0 0 % (5) With C org (%) being the organic carbon content and ash (%) the total ash content of the (RE-)biochar. The hydrogen to organic carbon molar ratio (H:C org ) of the bulk sample was corrected for geogenic hydrogen using equation 6 . H B i o : C o r g = H % B u l k − ( f r o c k * H % r o c k ) M H * M C C o r g % (6) With H:C orgBio being the hydrogen of the biogenic fraction to C org molar ratio, i.e., the bulk ratio corrected for geogenic hydrogen, %H Bulk and C org content of the bulk sample, f rock the rock fraction of the sample, H% rock the hydrogen content of the basanite and M C and M H the molar mass of carbon and hydrogen. The carbon content of the rock was below the detection limit, and we assume that all rocks relevant to ERW do not contain organic carbon. Solid state electrical conductivity (SEC) was measured using a Black Gauss I conductivity meter [ 79 ] while applying 5 t pressure (equivalent to 160 MPa) to the sample. The mineralogical composition of selected RE-biochars was measured by XRD on a D8 Advance (Bruker, Billerica USA) performed by QMineral (Heverlee, Belgium). Thermogravimetric analysis (TGA) was conducted using an STD 650 TG-DSC system (Waters, New Castle, United States of America). Dry samples (5 mg) were heated at open, pre-weighed alumina crucibles. The temperature was then increased from 50 °C to 1000 °C at a rate of 10 °C min ⁻ ¹ under N 2 atmosphere with a flow of 50 mL min ⁻ ¹. The recorded total weight loss was adjusted for the sample’s total ash content (including rock content) to represent the weight loss of daf biochar. The fraction of biochar that remained resistant to thermal degradation up to 1000 °C is referred to as BC 1000C . Benzenepolycarboxylic acids marker (BPCA) were extracted and analyzed in duplicate following Glaser et al. [ 80 ] and Brodowski et al. [ 81 ]. In brief, the (RE)-biochar samples were digested using trifluoroacetic acid to remove metal ions and organic matter including carbonates and C org other than those in aromatic moieties. Then the samples were oxidized in a pressurized vessel using nitric-acid. The digests were purified from remaining polyvalent cations using exchange resins. After freeze-drying, BPCAs were trimethylsilyl derivatized and analyzed by gas chromatography connected with a flame ionization detector (GC-FID) (GC-2010 Shimadzu, Kyoto, Japan). Two types of analytical pyrolysis were performed. Firstly, hydropyrolysis (HyPy) was performed according to Meredith et al. [ 32 ]. In brief, 300 mg were mixed with 10 wt% ammonium molybdate-tetrahydrate as a catalyst. The samples were then heated in a hydrogen purged reactor under 150 bar pressure, first from ambient temperature to 250 °C at a rate of 300 °C min ⁻ ¹, and subsequently from 250 °C to 550 °C at 8°C min ⁻ ¹, where samples were held for 2 minutes. The residual sample was weighed and analyzed for its C org content, referred to as BC HyPy and presented in percent of the sample’s initial C org . Secondly, using a HAWK sequential-pyrolyzer with coupled TOC analyzer (Wildcat Technologies, Humble, Texas USA). Here, 10 mg were inserted into the pyrolyzer preheated to 300 °C and held for 3 min under helium atmosphere. The mass of the carbon released as CO and CO 2 was continuously measured and is referred to as S1 and relates to free hydrocarbons such as oils [ 76 ]. Then the sample was heated at 25 °C min -1 to 650 °C with the mass of volatilized carbon summarized as S2. After cooling to 150 °C, the atmosphere was changed to oxygen, and the sample was re-heated to 850 °C at 25 °C min -1 oxidizing the residual carbon [ 82 ]. S1 + S2 was defined as the reactive, labile carbon and the residual carbon was considered unreactive under the conditions applied [ 35 , 76 ]. Fourier transformed infrared spectroscopy was conducted using attenuated total reflectance (ATR) mode with an Invenio X FT-IR Spectrometer (Bruker Corporation, Billerica, USA). Infrared absorbance was determined from 60 consecutive scans, covering a wavenumber range of 400–4000 cm ⁻ ¹. The absorbance spectrum was then smoothed and baseline-corrected using the software Spectragryph v.1.2.26.1. Raman spectroscopy was conducted under a LabRAM HR 800 Raman microscope (HORIBA Europe GmbH, Oberursel, Germany), which was coupled to an BX41 light microscope (Olympus Corporation, Tokyo, Japan). All measurements used a 532 nm laser (5 mW), which scanned a 100x100 µm area. Spectral acquisition time was 10 s. Five measurements were conducted per treatment and spectra converted D/G intensity- and area ratios. The baseline correction was done using the LabSpec 6 software (Horiba) and consecutive band-fitting according to Ferrari & Robertson (2000) [ 83 ] using a Lorentzian line shape (D-band) and a Breit-Wigner-Fano line shape (G-band) with a self-made Matlab-script. Fast field cycling 1 H nuclear magnetic resonance relaxometry ( 1 H FFC-NMR, i.e., 1 H Relaxometry) was performed following Conte (2021) [ 59 ]. Briefly, samples of 1 g sample was weighed in a 10 mm NMR tubes, then water was added in 2.5:1 ratio. The mixture was vortexed for 5 minutes and left to settle for 24 h. Measurements were conducted on a Stelar Smartracer Fast-Field-Cycling Relaxometer (Stelar SRL, Mede, Italy) set to 25 °C. The proton spins were polarized at a polarization field (B POL ) corresponding to a proton Larmor frequency (n L ) of 10 MHz for a period (T POL ) of about five times the T 1 estimated at this frequency. After each B POL , the magnetic field intensity (B RLX ) was set at the proton Larmor frequency, n L , of 1 MHz. The period τ, during which B RLX was applied, has been varied on 32 logarithmic spaced time sets. Free induction decays (FID) at each τ value were recorded following a single 1 H 90 ° pulse applied at an acquisition field (B ACQ ) corresponding to n L of 7.2 MHz. A time domain of 100 μs sampled with 512 points was applied. Field-switching time was 3 ms, while spectrometer dead time was 15 μs. For all the experiments, a recycle delay of 2 s was used. All decay curves acquired were analyzed by the UPEN algorithm to obtain the relaxograms [ 84 , 85 ]. Relaxograms were finally used to calculate the Pore Connectivity Index (PCI) [ 86 ] (additional S12 Text ). For SEM, RE-biochar pellets were mounted on an aluminum sample holder using carbon pads (Plano GmbH, Wetzlar, Germany) and sputter-coating them with gold (3–5 nm) using a Cressington 108auto (TESCAN GmbH, Dortmund, Germany). Analysis was conducted with a JSM-6610 LV (JEOL Ltd., Tokyo, Japan) at a working distance of 11 mm and acceleration voltage of 15 kV. Backscattered electron images (BES) were acquired, and Energy-dispersive X-ray (EDX) analysis of the same clippings was carried out using a 20 mm² Oxford X-max detector (Oxford Instruments, Abingdon, United Kingdom). For Scanning Transmission Electron Microscopy (STEM) with Electron Energy Loss Spectroscopy (EELS) specimens, Re-biochar samples (< 3 mm), were embedded in epoxy resin (Spezifix 40, Struers, Willich, Germany). Ultrathin sections of 50 nm were prepared using a Leica EM UC6-NT ultramicrotome (Leica Microsystems, Vienna, Austria) equipped with a 35° ultra diamond knife (Diatome, Biel, Switzerland). The sections were transferred onto lacey carbon-coated copper grids using a Perfect Loop (Diatome). The measurements were performed using a monochromated probe corrected FEI Titan G2 60–300 STEM-microscope with a Schottky-type X-FEG electron source operated at 300 kV. The microscope was equipped with a Gatan Imaging Filter, Quantum including a direct electron detection camera (K2 Summit) and a CCD camera (Ultrascan1000) with dual-EELS capability. The microscope was operated in monochromated mode with a semi-convergence angle of 15.6 mrad and a beam current of about 200 pA, resulting in a spatial resolution of 0.12 nm and an energy resolution at full-width at half maximum of 0.3 eV. The measurements were performed at a temperature of −160 °C using a cryo TEM-holder (Mel-Build, Fukuoka, Japan). The high angular annual dark field (HAADF) detector was used for micrographs acquisition. Gas adsorption was performed using nitrogen isotherms at 77 K on an AUTOSORB-IQ volumetric sorption device (3P-Instruments GmbH & Co KG, Odelzhausen, Germany). Samples of 0.1-0.2 g biochar were degassed at 150 °C for 12 h with a final vacuum of <10 ⁻ ² Pa applied before analysis. Surface area (Brunauer-Emmett-Teller method) was calculated following the guidelines of DIN ISO 9277:2014. The pore volume distribution is inferred from the total pore volume determined at P/P 0 = 0.99 (Gurvich’s law) and measured adsorption isotherms according to the density functional theory (DFT) [ 87 ]. The magnetic susceptibility was measured on 6.4x10 -6 m 3 cubes of manually compressed material. Measurements were conducted in a 200 A m -1 field at low (976 Hz) and high (15616 Hz) frequency (χlf and χhf) using a MFK1-FA Kappabridge (AGICO Inc., Brno, Czech Republic). The frequency dependent magnetic susceptibility was calculated as [(χlf—χhf)/χlf] × 100 [ 57 , 60 ]. Random Reflectance (Ro%) was measured on (RE)-biochar fragments between 63 and 1000 µm, that were embedded in an epoxy-resin and polished (ISO 7404−2 2009). White light reflectance measurements (ISO 7404−5, 2009) were carried out using a Zeiss Axio Imager II microscope (Zeiss, Oberkochen, Germany) with integrated Discus-Fossil system (Hilgers Technisches Buero, Königswinter, Germany). Measurements were conducted manually on n = 500 randomly selected, exposed macerals, with each measurement covering an area of 0.3 µm². Reflectance measurements were calibrated using KB N Lasf1.317 and KB cubic zirconia 3.11 standards. 4.3. Statistical considerations Rock-enhanced biochars were produced in a single continuous batch, with RE-biochar yield recorded at regular intervals and the coefficient of variation of f b and y c calculated. In general, analyses were conducted on representative samples without replication ( n = 1). Depending on the analytical method varying numbers of repeated measures were conducted per sample (e.g., Raman spectroscopy with n = 5, FTIR with n = 60, and random reflectance with n = 500). Mean, median, skewness and kurtosis of each Ro distribution were calculated using Microsoft Excel. Supporting information S1 Table Biomass analysis. (PDF) S2 Table Rock characterization. (PDF) S3 Table Feedstock composition (2 nd batch). (PDF) S4 Table Biochar basic characterization (2 nd batch). (PDF) S5 Fig ATR-FTIR absorbance spectra. (PDF) S6 Fig Raman spectra (D/G ratios). (PDF) S7 Fig Graphical Abstract. (TIF) S7 Table Biochar main and trace elements (1st batch). (PDF) S8 Table Hydrogen in small hydrocarbons. (PDF) S9 Fig Specific surface area and pore volume distribution. (PDF) S10 Fig STEM-EELS transects with inverted beam trajectory. (PDF) S11 Fig SEM/EDX potassium distribution mapping. (PDF) S12 Text Methods – Pore Connectivity Index. (PDF)