FULL PAPERS Journal of the Physical Society of Japan Photon-Assisted Tunneling in Double Quantum Dot: Application of Scattering Theory arXiv:2606.26622v1 [cond-mat.mes-hall] 25 Jun 2026 Miyu Umebayashi and Mikio Eto * Faculty of Science and Technology, Keio University, Hiyoshi, Yokohama 223-8522, Japan We theoretically examine the photon-assisted tunneling (PAT) in a double quantum dot (DQD) in parallel when one of the quantum dots (QDs) is irradiated by an AC field. First, we formulate the PAT in a single QD by solving the time-dependent Schrödinger equation using the scattering theory. The QD has an oscillating energy level, ε(t) = ε0 + eVAC cos ωt, and is connected to two leads by the tunnel coupling Γ. We show that the resonant tunneling takes place through energy levels of the polariton, ε0 + Nℏω (N = 0, ±1, ±2, · · · ), when Γ ≪ ℏω (PAT) and through the energy level ε(t) when Γ ≫ ℏω (adiabatic transport). Then, the scattering theory is applied to the PAT in the DQD in the presence of magnetic flux penetrating between the QDs. We observe the Aharonov–Bohm effect not only in the main peak (N = 0) but also in subpeaks (N , 0), indicating coherent transport through the polariton states. Our theory is also applicable to the DQD in the three-terminal geometry. We demonstrate the phase measurement through the irradiated QD and show that the measured phase shift changes continuously from 0 to π around both the main peak and subpeaks. 1. Introduction The single electron tunneling accompanied by photon emission or absorption is called photon-assisted tunneling (PAT). It was first reported by Dayem and Martin in 1962 in an experiment on a superconducting film between two insulators in a microwave field.1) In the following year, Tien and Gordon described the PAT in the superconducting diode using a model of an oscillating energy level.2, 3) In the study of mesoscopic physics, the transport through a semiconductor quantum dot (QD) in an AC field is one of the important issues and has been studied for a long time. There are two extreme cases concerning the strength Γ of tunnel coupling to external leads and the frequency ω of the AC field.4) The PAT was observed in the case of Γ ≪ ℏω: When the energy * eto@rk.phys.keio.ac.jp 1/27 FULL PAPERS J. Phys. Soc. Jpn. level is given by FAC (t) = ε0 + eVAC cos ωt (1) in the QD, the conductance shows a main peak when the Fermi level EF matches ε0 and subpeaks when EF = ε0 + Nℏω (N = ±1, ±2, · · · ).5–13) This indicates the transport through the QD with the emission or absorption of |N| photons. In other words, the transport takes place through the polariton states of the energy levels ε0 + Nℏω in the QD. The experimental results are well explained by the Tien–Gordon theory. In the opposite case of Γ ≫ ℏω, adiabatic transport takes place through the energy level ε(t). A notable example of the adiabatic transport is the single-electron turnstile applied to the current standard.14–17) Lately, the PAT was observed by irradiating terahertz (THz) light on an InAs QD12) or a single molecule of C60 .13) The light is focused on the QD beyond the diffraction limit. A sensitive detector of the THz light was proposed, utilizing the interlevel transition in an InAs QD.18) More generally, the interaction between an electron in the QD and a photon, e.g., cavity QED, is being studied extensively for quantum information processing.19, 20) Therefore, deep understanding of the PAT and other transport phenomena in an AC field will be required for the application of the QD to future technology. In this paper, we theoretically examine the transport through a single QD and a double quantum dot (DQD) in parallel when the energy level is given by Eq. (1). We disregard the electron–electron interaction U in the QDs. We do not expect U to cause a qualitative change, such as the Kondo effect, in the vicinity of the electric current peaks mainly studied in this paper. We solve the time-dependent Schrödinger equation using the scattering theory21, 22) for the following reasons: (i) First, we reformulate the electric current through a single QD in both the cases of PAT and adiabatic transport. Although the current expression in the former was previously derived using the Keldysh nonequilibrium Green’s function method23) or others,3, 24) our tutorial method intuitively illustrates the physical pictures of the time-dependent transport phenomena for both Γ ≪ ℏω and Γ ≫ ℏω. (ii) In the DQD in parallel, we assume that one of the QDs has the oscillating energy level in Eq. (1) and the other has a constant energy level. The infinite series of the perturbation with respect to the tunnel coupling to the leads enables the calculation of the electric current to the second-order in eVAC /(2ℏω). In the presence of magnetic flux penetrating between the QDs, we elucidate the Aharonov–Bohm (AB) interference effect on the transport through the polariton states when the AC field is considered using Eq. (1) in a classical way. Note that the 2/27 FULL PAPERS J. Phys. Soc. Jpn. AB oscillation in the DQD in the absence of the AC field has been studied experimentally25, 26) and theoretically.27–32) In the case of its presence, however, few works have been reported. (iii) The scattering theory is also applicable to the DQD in the three-terminal geometry. We demonstrate the phase measurement through the QD with the oscillating energy level using the other QD as a reference arm of the “double slit interference experiment”.33) The phase measurement is impossible in the transport experiment in the two-terminal geometry owing to the restriction of Onsager’s reciprocal theory.34) The measurement of the phase shift through a QD was reported using a small ring with an embedded QD in a three- or four-terminal geometry in the absence of the AC field.35–38) In its presence, we show that the measured phase shift changes continuously from 0 to π around both the main peak and subpeaks in accordance with the Breit–Wigner resonance. We do not observe the “phase lapse” between the main peak and a subpeak, as reported previously between successive current peaks without the AC field.35, 37, 39, 40) This paper is organized as follows. In Sect. 2, we explain our models and formulation based on the time-dependent Schrödinger equation. Section 3 is devoted to the PAT and adiabatic transport through a single QD using the scattering theory. We mention the relationship between our Green’s function and that of the Floquet theory.41–43) In Sect. 4, we derive the electric current through the DQD in parallel when one of the QDs has an oscillating energy level. In the two-terminal setup, we show the AB effect on the transport through the polariton states. In the three-terminal setup, we discuss the phase measurement through the oscillating energy level. The conclusions are given in Sect. 5. 2. Model and Calculation Method 2.1 Model We examine three models depicted in Fig. 1; single QD with an energy level ε1 (t) = FAC (t) in Eq. (1), DQD with the oscillating energy level in one of the QDs and a static level in the other in two- and three-terminal geometries. We describe the Hamiltonian for the DQD model in Fig. 1(b) in this subsection. For a single QD in Fig. 1(a), we set ε2 = 0 in Eq. (3) (2) (2) and VLk = VRk ′ = 0 in Eq. (5). For the three-terminal situation in Fig. 1(c), we divide the summation over k in lead R into those in leads Ra and Rb in Eqs. (4) and (5). The Hamiltonian is given by H(t) = Hdot (t) + Hleads + HT , 3/27 (2) FULL PAPERS J. Phys. Soc. Jpn. model_修正版 (a) 1 1 𝑉𝑅,𝑘 ′ 𝑉𝐿,𝑘 L R 𝜀1 𝑡 (b) 𝜀2 2 𝑉𝐿,𝑘 2 𝑉𝑅,𝑘 ′ 𝑒 𝑖𝜙 L R 1 1 𝑉𝐿,𝑘 𝜀1 𝑡 (c) 𝜀2 2 𝑉𝐿,𝑘 𝑉𝑅,𝑘 ′ 2 𝑉𝑅,𝑘 ′ 𝑒 𝑖𝜙 Ra L 1 𝑉𝑅,𝑘 ′ 1 Rb 𝑉𝐿,𝑘 𝜀1 𝑡 Fig. 1. (a) Model for a single QD with an oscillating energy level ε1 (t) = FAC (t) in Eq. (1). The QD is (1) (1) connected to leads L and R by the tunnel couplings VLk and VRk ′ , respectively. (b, c) Model for a DQD in parallel in a two- or three-terminal geometry. The energy levels in the QDs are ε1 (t) = FAC (t) in QD1 and time( j) ( j) independent ε2 in QD2. QD j is connected to leads L and R by the tunnel couplings VLk and VRk ′ , respectively. (2) (2) iϕ VRk ′ = VRk′ e , where ϕ = 2πΦ/(h/e) is the AB phase for the magnetic flux Φ penetrating between the QDs. (1) ′ In panel (c), lead Rb is connected to QD1 [by VRk ′ when state k belongs to the lead] but not to QD2. where Hdot (t) = ε1 (t)d1† d1 + ε2 d2† d2 , XX Hleads = εk a†αk aαk , α=L,R (4) k X XX  ( j) † HT = Vαk aαk d j + h.c. . α=L,R (3) k (5) j=1,2 Here, d†j and d j are the creation and annihilation operators of an electron in QD j while a†αk and aαk are those in lead α (= L, R) with state k. The energy levels in the QDs are given by ε1 (t) = FAC (t) and time-independent ε2 . The spin of the electrons is omitted in this paper. 4/27 FULL PAPERS J. Phys. Soc. Jpn. ( j) . The magnetic In the tunnel Hamiltonian HT , QD j is connected to state k in lead α by Vα,k flux Φ penetrating between the QDs is taken into account by the AB phase ϕ = 2πΦ/ (h/e). (1) (2) (1) (2) (2) iϕ , and VRk , VLk and VLk We choose the gauge in such a way as VRk ′ are real and ′ = VRk′ e positive. In the case of a single QD, the strength of the tunnel coupling to lead α is characterized by the linewidth, Γα (ε) = 2π X 2 (1) δ (εk − ε) . Vα,k (6) k Assuming that its dependence on ε is weak around the Fermi level EF , we simply denote Γα hereafter. The total linewidth in the QD is given by Γ = Γ L + ΓR . (7) In the DQD in the two-terminal setup, we define the linewidth function Γα in a matrix form of 2 × 2 corresponding to QD1 and QD2 by Xh i (i) ∗ ( j) Γαi j = 2π Vα,k Vα,k δ (εk − ε) (8) k around ε ≃ EF . The diagonal element Γαj j indicates the linewidth in QD j due to the tunnel coupling to lead α. For the off-diagonal element in Eq. (8) , we define pα as q α pα = Γ12 / Γα11 Γα22 (9) (0 ≤ pα ≤ 1), which represents the coherence between the QDs through lead α.33, 44) pα is identical to the overlap integral between the conduction modes coupled to QD1 and QD2 in lead α at the energy ε ≃ EF .45) In the case of a single conduction channel in the lead, pα = 1 and the connection between the QDs is maximal. With an increase in channel number, pα usually decreases. When pα = 0, the two QDs are independent of each other. In experiments, pα is determined by the device structure. The total linewidth function in the DQD is given by Γ = Γ L + ΓR . (10) Similarly, we introduce the linewidth functions ΓL , ΓRa , and ΓRb for the model in Fig. 1(c). Since QD2 is disconnected from lead Rb, ΓRb = diag(ΓRb 11 , 0) and pRb = 0. 2.2 Formulation Using the time-dependent Schrödinger equation, ∂ iℏ |ψ(t)⟩ = [Hdot (t) + Hleads + HT ] |ψ(t)⟩ , ∂t 5/27 (11) FULL PAPERS J. Phys. Soc. Jpn. we perform the perturbative calculation with respect to HT . For the DQD model in Fig. 1(b), the wavefunction is written as X E XX Cα,k (t)e−iεk (t−t0 )/ℏ |α, k⟩ , C j (t)e−iE j (t)/ℏ d j + |ψ(t)⟩ = α=L,R j=1,2 (12) k E where d j = d†j |0⟩ and |α, k⟩ = a†αk |0⟩ with |0⟩ being the vacuum state, Z t E1 (t) = ε1 (t′ )dt′ (13) t0 = ε0 (t − t0 ) + eVAC (sin ωt − sin ωt0 ), ω (14) and E2 (t) = ε2 (t − t0 ). The substitution of Eq. (12) into Eq. (11) yields Eqs. (A·3) and (A·4) in Appendix A. From these equations, we derive the transition rate to the lowest order in HT (Fermi’s golden rule; Sect. 3.1) and the scattering matrix to the infinite order in HT (Sects. 3.2 and 4). In the following sections, we denote the Fermi level in leads L and R (Ra, Rb) by µL and µR (µRa , µRb ), respectively. µL − µR = eVbias under the bias voltage Vbias . We set µRa = µRb ≡ µR in Fig. 1(c). We change the original energy level ε0 in the QD, the first term on the right side of Eq. (1), which can be tuned by the gate voltage in experiments. 3. Single Quantum Dot (2) In this section, we examine the single QD model depicted in Fig. 1(a), by setting VLk = (2) VRk = 0 and C2 (t) = 0 in Eqs. (A·3) and (A·4). We begin with the sequential tunneling to the lowest order in HT . Next, we obtain the exact formula of the electric current through the summation of the perturbative series to the infinite order. 3.1 Sequential tunneling First, we assume that the transport through the QD takes place sequentially from a lead to the QD and from the QD to another lead. This assumption will be verified at high temperatures of kB T ≫ Γ in the next subsection. We calculate the transition rate between the QD and leads to the lowest order in HT in Appendix A.1. We examine the two extreme cases of Γ ≪ ℏω and Γ ≫ ℏω. 6/27 FULL PAPERS J. Phys. Soc. Jpn. (a) dI/dμ L /(e/h) 0.1 0.0 −20 −10 0 10 20 1 dI/dμ L /(e/h) (b) 0 Fig. 2. −10 0 (ε 0 − μ L )/Γ 10 Differential conductance dIL→R /dµL as a function of ε0 for a single QD depicted in Fig. 1(a), when Γ ≪ ℏω with Γ being the linewidth due to the tunnel coupling to the leads (ΓL = ΓR = Γ/2). The energy level in the QD is ε1 (t) = FAC (t) in Eq. (1). The temperature is (a) kB T ≫ Γ [kB T/Γ = 3; Eq. (16)] and (b) kB T ≪ Γ [Eq. (30)]. The frequency of the AC field is ℏω/Γ = 10 and its amplitude is eVAC /Γ = 5 (broken line) and 10 (solid line). 3.1.1 Case of Γ ≪ ℏω In the case of Γ ≪ ℏω, the transition rate from the QD to lead α is given by Eq. (A·9). This results in the electric current i2 h i2 e Γ L ΓR X h IL→R = JN (ṼAC ) JN ′ (ṼAC ) [ fL (ε0 + Nℏω) − fR (ε0 + N ′ ℏω)], ℏ ΓL + ΓR N,N ′ (15) where ṼAC = eVAC /(ℏω), JN is the Nth Bessel function, and fα (E) = [1 + e(E−µα )/(kB T ) ]−1 is the Fermi distribution function in lead α at temperature T . This expression was obtained previously.3, 24) The differential conductance i2 ε0 + Nℏω − µL dIL→R e ΓL ΓR 1 Xh = JN (ṼAC ) cosh−2 dµL ℏ ΓL + ΓR 4kB T N 2kB T (16) shows a peak structure: A main peak at µL = ε0 and subpeaks at µL = ε0 + Nℏω (N = h i2 ±1, ±2, · · · ) with the weight of JN (ṼAC ) . This indicates that the polariton states are formed in the QD at energy levels ε0 + Nℏω. Note that we do not include the factor 2 for the spin degrees of freedom in calculating the electric current and differential conductance. 7/27 FULL PAPERS J. Phys. Soc. Jpn. dI/dμ L /(e/h) (a) 0.1 0.0 −20 −10 0 10 20 0.50 dI/dμ L /(e/h) (b) 0.25 0.00 Fig. 3. −10 0 10 (ε 0 − μ L )/Γ Time-averaged differential conductance dIL→R /dµL (t) as a function of ε0 for a single QD depicted in Fig. 1(a), when Γ ≫ ℏω with Γ being the strength of tunnel coupling to the leads (ΓL = ΓR = Γ/2). The energy level in the QD is ε1 (t) = FAC (t) in Eq. (1). The temperature is (a) kB T ≫ Γ [kB T/Γ = 3; time-average of Eq. (18)] and (b) kB T ≪ Γ [that of Eq. (33)]. The amplitude of the AC field is eVAC /Γ = 1 (broken line), 3 (dotted line), and 5 (solid line). Figure 2(a) shows dIL→R /dµL in Eq. (16) as a function of ε0 . Besides the main peak, the subpeaks of N = ±1 appear in the shoulders of the main peak. The peak widths are determined by the temperature kB T . 3.1.2 Case of Γ ≫ ℏω In the adiabatic case of Γ ≫ ℏω, electrons do not feel the oscillation of the energy level during the transport through the QD. Then, the electric current flows through the energy level ε1 (t),  e ΓL ΓR  fL (ε1 (t)) − fR (ε1 (t)) . ℏ Γ L + ΓR The differential conductance is given by dIL→R e ΓL ΓR 1 ε1 (t) − µL (t) = cosh−2 , dµL ℏ ΓL + ΓR 4kB T 2kB T which oscillates by the time-dependent energy level in Eq. (1). IL→R (t) = (17) (18) If the measurement time is much longer than the period of the AC field, 2π/ω, the time8/27 FULL PAPERS J. Phys. Soc. Jpn. (a) (b) (𝑖) (𝑗) 𝑉𝑅,𝑘 ′ 𝑉𝑅,𝑘 ′ 𝑅, 𝑘′; 𝐸 + 𝑁ℏ𝜔 𝑅, 𝑘′; 𝐸 + 𝑁ℏ𝜔 QD𝑖 𝑖 ∗ 𝑉𝛼,𝑞 QD𝑗 𝑗 ∗ 𝑉𝐿,𝑘 (𝑗) 𝑉𝛼,𝑞 𝐿, 𝑘; 𝐸 𝛼, 𝑞; 𝐸 + 𝑁′ℏ𝜔 QD𝑗 𝑗 ∗ 𝑉𝐿,𝑘 𝐿, 𝑘; 𝐸 Fig. 4. (a) First and (b) second terms of the perturbation series of the T-matrix with respect to the tun- (1) (1)∗ nel Hamiltonian HT : VR,k with G N,0 (E) in Eq. (21) for the single QD (i = j = 1) and ′ G N,0 (E)V L,k P ( j)∗ (i) i, j=1,2 VR,k′ [G N,0 (E)]i, j VL,k with GN,0 (E) in Eq. (35) for the DQD. N is the number of photons in the final state. QD j indicates the unperturbed Green’s function of the QD, G(0) N1 ,N2 (E) in Eq. (22), or that of the DQD, G(0) N1 ,N2 (E) in Eq. (36), where N1 (N2 ) is the number of photons after (before) the propagation through the QD or DQD. (α, q; E) represents the propagator in lead α, 1/(E − εq + iη). averaged conductance dIL→R /dµL (t) is observed. We plot the value as a function of ε0 in Fig. 3(a). The width of a single peak around ε0 = µL is determined by the sum of kB T and the amplitude of the AC field, eVAC . 3.2 Resonant tunneling Now we perform the summation of the perturbative series to the infinite order to obtain the exact formula for the electric current. Following the scattering theory,21, 22) we obtain the scattering matrix in an infinite series of HT from Eqs. (A·3) and (A·4) by the method of successive substitution. 3.2.1 Case of Γ ≪ ℏω When Γ ≪ ℏω, the scattering matrix from state k in lead L to state k′ in lead α is given by ∞ X S L,k→α,k′ = δα,L δk,k′ − 2πi ⟨α, k′ |T N |L, k⟩δ(εk′ − εk − Nℏω). (19) N=−∞ 9/27 FULL PAPERS J. Phys. Soc. Jpn. Here, T N is the T-matrix accompanied by the emission of N photons for N > 0 or absorption of |N| photons for N < 0. It is written as (1) (1)∗ ⟨α, k′ |T N |L, k⟩ = Vα,k ′ G N,0 (εk )V L,k , (20) with ∞ X i G N,0 (E) = G(0) N,0 (E) − 2 N ′ =−∞ (0) G(0) N,N ′ (E)ΓG N ′ ,0 (E) + · · · (21) and G(0) N,N ′ (E) = X JN−m (ṼAC )JN ′ −m (ṼAC ) E − ε0 + mℏω + iη m (22) (0) ′ with a positive infinitesimal η. G(0) N,N ′ (E) = G N−N ′ ,0 (E + N ℏω) is the unperturbed Green’s function of the QD for an electron of energy E with N ′ (N) photons before (after) the propagation through the QD. The first and second terms of the infinite series in the T-matrix, (1) (1)∗ VR,k ′ G N,0 (E)V L,k , are schematically shown in Figs. 4(a) and 4(b), respectively. In the second term on the right side of Eq. (21), the virtual state |α, q⟩ with N ′ photons is taken into account by the self-energy ΣT (E + N ′ ℏω) = −iΓ/2, where XX (1)∗ ΣT (E) = Vα,q α=L,R q 1 V (1) , E − εq + iη α,q (23) assuming the wide-band limit in the leads. Note that the Green’s function G N,0 (E) is a component of the retarded Green’s function of the QD, 1 ⟨{d(t), d† (t′ )}⟩θ(t − t′ ), (24) iℏ with the step function θ(x) = 1 (x > 0) and 0 (x < 0). G N,0 (E) is also related to the Green’s Gr (t, t′ ) = function in the Floquet theory, as shown in Appendix B. From Eq. (21), we exactly obtain G N,0 (E) = X JN−m (ṼAC )J−m (ṼAC ) m using the relation of P E − ε0 + mℏω + iΓ/2 N ′ JN ′ −m (ṼAC )JN ′ −n (ṼAC ) = (25) Jn−m (0) = δm,n . Using the transition rate from |L, k⟩ to |R, k′ ⟩, wL,k→R,k′ = 2π X |⟨R, k′ |T N |L, k⟩|2 δ(εk′ − εk − Nℏω), ℏ N and a similar expression for wR,k′ →L,k ,21, 22) the electric current is written as X     IL→R = e wL,k→R,k′ fL (εk ) 1 − fR (εk′ ) − wR,k′ →L,k fR (εk′ ) 1 − fL (εk ) k,k′ 10/27 (26) (27) FULL PAPERS J. Phys. Soc. Jpn. XZ  e 2 = ΓL ΓR dε G N,0 (ε) fL (ε) − fR (ε) h N h i2 XZ JN (ṼAC )   e = ΓL ΓR dε fL (ε) − fR (ε) . 2 2 h (ε − ε0 + Nℏω) + (Γ/2) N (28) The same expression was obtained previously.23) This yields the differential conductance h i2 Z X J ( Ṽ ) N AC dIL→R e ΓL ΓR ε − µL = dε cosh−2 , (29) 2 2 dµL h 4kB T N (ε − ε0 + Nℏω) + (Γ/2) 2kB T which is valid for any temperature T . When kB T ≪ Γ, it can be approximately written as h i2 X J ( Ṽ ) N AC dIL→R e = ΓL ΓR . (30) dµL h (µL − ε0 + Nℏω)2 + (Γ/2)2 N This means resonant tunneling through the energy levels of the polariton, ε0 − Nℏω. When kB T ≫ Γ, Eq. (29) results in the same expression as Eq. (16). Hence, the treatment of the sequential transport is justified for kB T ≫ Γ. In Fig. 2(b), we plot dIL→R /dµL in Eq. (30) for kB T ≪ Γ as a function of ε0 . We clearly observe subpeaks at µL = ε0 ± ℏω in addition to the main peak at µL = ε0 . With an increase in the amplitude of the AC field, the height of the main peak decreases and that of the subpeaks increases. 3.2.2 Case of Γ ≫ ℏω In the case of Γ ≫ ℏω, the resonant tunneling takes place through the energy level ε1 (t). The electric current is given by Z   e 1 IL→R (t) = ΓL ΓR dε f (ε) − f (ε) . L R h [ε − ε1 (t)]2 + (Γ/2)2 The differential conductance is Z e ΓL ΓR 1 dIL→R −2 ε − µL (t) = dε cosh , dµL h 4kB T [ε − ε1 (t)]2 + (Γ/2)2 2kB T which yields approximately dIL→R e ΓL ΓR (t) = dµL h [µL − ε1 (t)]2 + (Γ/2)2 for kB T ≪ Γ and Eq. (18) for kB T ≫ Γ. (31) (32) (33) Figure 3(b) presents the time-averaged conductance dIL→R /dµL (t) for kB T ≪ Γ as a function of ε0 . We observe two peaks around µL = ε0 ± eVAC , which are extreme values of FAC (t) in Eq. (1). 11/27 FULL PAPERS J. Phys. Soc. Jpn. 2 dI/dμ L /(e/h) (a) 1 0 2 dI/dμ L /(e/h) (b) 1 0 2 dI/dμ L /(e/h) (c) 1 0 Fig. 5. −10 0 (ε 0 − μ L )/Γ 10 Differential conductance dIL→R /dµL as a function of ε0 for a DQD in the two-terminal geometry depicted in Fig. 1(b). The energy level in QD1 is ε1 (t) = FAC (t) in Eq. (1) while that in QD2 is ε2 = ε0 . The linewidths due to the tunnel coupling to the leads are ΓLjj = ΓRjj ≡ Γ/2 ( j = 1, 2) and pL = pR = 0.5 in Eq. (9). The frequency of the AC field is ℏω/Γ = 10 and its amplitude is (a) eVAC /Γ = 0, (b) 5, and (c) 10. The AB phase for the magnetic flux penetrating between the QDs is ϕ = 0 (solid line) or π (broken line). 4. Double Quantum Dot In this section, we discuss the DQD models in Figs. 1(b) and 1(c). We restrict ourselves to the case of PAT for Γ ≪ ℏω. As indicated in Appendix A, we obtain the scattering matrix S L,k→α,k′ as an infinite series of the perturbation in HT , which is related to the T-matrix by Eq. (19). The T-matrix is common to the models in two- and three-terminal geometries and is given 12/27 FULL PAPERS J. Phys. Soc. Jpn. by ⟨α, k′ |T N |L, k⟩ = X  ( j)∗ (i)  Vα,k ′ G N,0 (εk ) i, j V L,k (34) i, j=1,2 for the electron transfer accompanied by the emission of N photons (N > 0) or the absorption   of |N| photons (N < 0). Here, G N,0 (εk ) i, j is the (i, j) component of GN,0 (εk ) in a matrix form of 2 × 2 corresponding to QD1 and QD2, i X (0) G ′ (E)ΓG(0) N ′ ,0 (E) + · · · 2 N ′ N,N "  −1 # i (0) (0) ˆ = G (E) 1̂ + Γ̂G (E) , 2 N,0 GN,0 (E) = G(0) N,0 (E) − using the unperturbed Green’s function of the DQD,   X JN−m (ṼAC )JN ′ −m (ṼAC )  δN,N ′ (0)  . GN,N ′ (E) = diag  , E − ε + mℏω + iη E − ε + Nℏω + iη  m 0 (35) (36) 0 In the second line of Eq. (35), we introduced the supermatrices Gˆ(0) (E) and Γ̂, the (N, N ′ ) ′ components of which are G(0) N,N ′ (E) and ΓδN,N , respectively, for the compact form. We cannot analytically sum up all the terms in the infinite series in Eq. (35) for the DQD as was done in the case of a single QD in Eq. (25). Instead, we obtain the Green’s function to the second order of ṼAC /2 = eVAC /(2ℏω) in Appendix C. In the two-terminal geometry in Fig. 1(b), Eq. (27) yields the electric current Z n h i   eX A dε Tr G0,N (ε)ΓR GN,0 (ε)ΓL fL (ε) 1 − fR (ε + Nℏω) IL→R = h N h i  o A +Tr G0,N (ε)ΓL GN,0 (ε)ΓR fR (ε) 1 − fL (ε + Nℏω) , (37) A where G0,N (ε) is the adjoint matrix of GN,0 (ε) in Eq. (35). In the three-terminal geometry in Fig. 1(c), we set µRa = µRb ≡ µR . In Eq. (27), we take the summation over state k′ only in lead Ra for the electric current from lead L to Ra, IL→Ra . Its expression is given by Eq. (37) on replacing ΓR by ΓRa . We calculate IL→R and IL→Ra to the second order in ṼAC /2. 4.1 Double quantum dot with two terminals We discuss the calculated results for the PAT in the DQD in the two-terminal geometry depicted in Fig. 1(b). The energy levels are ε1 (t) = FAC (t) in QD1 and ε2 = ε0 in QD2. We set ΓLjj = ΓRjj ≡ Γ/2 ( j = 1, 2) and pL = pR = 0.5. Figure 5 presents the differential conductance dIL→R /dµL as a function of ε0 , with the AB phase ϕ = 0 (solid line) or π (broken line). The amplitude of the AC field is (a) eVAC /Γ = 0, 13/27 FULL PAPERS J. Phys. Soc. Jpn. Peak height/(e/h) 2 1 (a) Peak height/(e/h) 0 0.3 (b) 00 1 ϕ/2π Fig. 6. Differential conductance dIL→R /dµL as a function of the AB phase ϕ, i.e., AB oscillation, for a DQD in the two-terminal geometry depicted in Fig. 1(b), for (a) the main peak (ε0 − µL = 0) and (b) the subpeaks (ε0 − µL = ±ℏω). The energy levels in the QDs and the linewidth functions are the same as in Fig. 5. The frequency of the AC field is ℏω/Γ = 10 and its amplitude is eVAC /Γ = 0 (solid line), 5 (broken line), and 10 (dotted line). (b) 5.0, and (c) 10. In the absence of the AC field in Fig. 5(a), the conductance peak is located at µL = ε0 . The AB effect causes the ϕ dependence of the peak height; the positive (negative) interference effect increases (reduces) the peak height for ϕ = 0 (π). In the presence of the AC field in Figs. 5(b) and 5(c), we observe the main peak at µL = ε0 and two subpeaks at µL = ε0 ± ℏω. The former decreases and the latter increases in height with increasing AC field. Note that both the main and subpeaks depend on the AB phase ϕ. We plot the AB oscillation of the main peak in Fig. 6(a) and that of the subpeaks in Fig. 6(b). The AC field suppresses the amplitude of the oscillation at the main peak and enhances it at the subpeaks. The interference effect at the subpeaks can be understood as follows. Consider the intermediate processes in the T-matrix depicted in Fig. 4. When N = ±1, the electron transport is accompanied by the emission or absorption of a photon. Then, the process in Fig. 4(a) does not involve the interference effect between the QDs since the intermediate state is QD1 only. In the process in Fig. 4(b), on the other hand, the interference exists when N ′ = 0 or N 14/27 FULL PAPERS J. Phys. Soc. Jpn. dI/dμ L /(e/h) 0.2 (a) 0.1 0.0 (b) ϕ max /π 1 0 -40 Fig. 7. -20 0 20 −(ε 0 − μ L )/Γ 40 (a) Differential conductance dIL→Ra /dµL as a function of ε0 for a DQD in the three-terminal geometry depicted in Fig. 1(c). The energy level in QD1 is ε1 (t) = FAC (t) in Eq. (1) while that in QD2 is (ε2 − µL )/Γ = 70. ΓLjj = ΓRa j j ≡ Γ/2 ( j = 1, 2) and pL = pRa = 0.5 in Eq. (9). The frequency of the AC field is ℏω/Γ = 40, whereas its amplitude is eVAC /Γ = 40 (solid line) and 0 (dotted line). The tunneling coupling between QD1 and Ra Rb lead Rb is ΓRb 11 /(Γ11 + Γ11 ) = 0.7. The AB phase for the magnetic flux penetrating between the QDs is ϕ = 0. (b) Measured phase shift ϕmax through QD1 as a function of ε0 . ϕmax is the AB phase at which dIL→Ra /dµL is maximal for a given ε0 . Note that the abscissa shows −ε0 in both panels. because an electron passes by both the QDs in the first or second intermediate state, respectively. Therefore, the interference effect is partly left for the subpeaks. In the case of N = 0 for the main peak, the interference exists in the processes in Figs. 4(a) and 4(b) with N ′ = 0 but does not in that in Fig. 4(b) with N ′ , 0. In consequence, the AB oscillation of the main peak is suppressed by the AC field. 4.2 Double quantum dot with three terminals We examine the PAT in the DQD in the three-terminal geometry depicted in Fig. 1(c), to demonstrate the phase measurement through QD1 with ε1 (t) = FAC (t) in Eq. (1). We set the energy level ε2 in QD2 far from µL [(ε2 − µL )/Γ = 70] to avoid the effect of its discreteness on the resonant tunneling through the polariton states in QD1. ΓLjj = ΓRa j j ≡ Γ/2 ( j = 1, 2) and pL = pRa = 0.5. Figure 7(a) shows the differential conductance dIL→Ra /dµL as a function of ε0 with the AB 15/27 FULL PAPERS J. Phys. Soc. Jpn. phase ϕ = 0. We choose a large value of ℏω to separate the main and subpeaks (ℏω/Γ = 40). For comparison, we plot a single peak of dIL→Ra /dµL in the absence of the AC field with a Ra Rb dotted line. The tunnel coupling to lead Rb is fixed at ΓRb 11 /(Γ11 + Γ11 ) = 0.7. Note that the abscissa shows −ε0 in Figs. 7 and 8. Both the main peak and subpeaks change with the AB phase ϕ, indicating an AB oscillation. We define the measured phase shift through QD1 as the AB phase ϕmax at which dIL→Ra /dµL is maximal for a given ε0 . In Fig. 7(b), we plot the measured phase as a function of ε0 . We observe the change in ϕmax from 0 to π around the subpeaks as well as the main peak with a decrease in ε0 . The change in ϕmax around the main peak is almost the same as that around a single peak in the absence of the AC field (dotted line). Figure 7(b) also indicates that ϕmax changes continuously from π to 0 between a subpeak and the main peak, i.e., there is no “phase lapse” between the peaks. Regarding the phase shift through a QD without the AC field, the abrupt change between the successive conductance peaks was reported35, 37, 39) and studied theoretically.40) This phase lapse takes place where the conductance vanishes between the peaks.40) In our case with the AC field, we observe neither the phase lapse nor the zero point of dIL→Ra /dµL between the main peak and a subpeak. We examine the role of the third lead, Rb, in the measurement of the phase shift through QD1. In Fig. 8, we plot ϕmax in the vicinity of the main peak (εcenter = µL ) and subpeaks Ra Rb (εcenter = µL ± ℏω), changing the tunnel coupling to lead Rb as (a) ΓRb 11 /(Γ11 + Γ11 ) = 0, (b) 0.4, and (c) 0.7. In the case of two terminals with ΓRb 11 = 0 in Fig. 8(a), the measured phase ϕmax abruptly changes by π at the peaks. (ϕmax seems to change gradually around one of the subpeaks, which should be due to the effect from the energy level ε2 in QD2.46) ) With an increase in the coupling to lead Rb, ϕmax changes more smoothly with ε0 for all the peaks. Finally, we discuss the shape of the measured phase ϕmax as a function of ε0 in Fig. 8(c) [and Fig. 7(b)] where the coupling to the third lead is sufficiently large. ϕmax behaves very similarly to one another around the main peak and subpeaks. It is also almost identical to that around a single peak in the absence of the AC field, as seen in Fig. 7(b). These functions of ϕmax (ε0 − εcenter ) are qualitatively the same as θQD defined by Γ1 /2 tan θQD = , (38) ε0 − εcenter L Rb where Γ1 = Γ11 + ΓRa 11 + Γ11 is the total linewidth in QD1. θQD is the phase shift through QD1 by the Breit–Wigner resonance when the coupling to QD2 is neglected. The reason is given in Appendix D. If we replace Γ1 and ε0 in Eq. (38) by the renormalized values due to the coupling to QD2, ϕmax would almost coincide with θQD , as discussed previously in the 16/27 FULL PAPERS J. Phys. Soc. Jpn. (a) ϕ max /π 1 0 (b) ϕ max /π 1 0 (c) ϕ max /π 1 0 −10 Fig. 8. −5 0 5 −(ε 0 − ε center )/Γ 10 Measured phase shift ϕmax through QD1 in the DQD in the three-terminal geometry depicted in Fig. 1(c), as a function of ε0 . The energy level in QD1 is ε1 (t) = FAC (t) in Eq. (1) while that in QD2 is (ε2 − µL )/Γ = 70. ϕmax is plotted in the vicinity of the main peak at εcenter = µL (solid line) and the subpeaks at εcenter = µL − ℏω (broken line) and εcenter = µL + ℏω (dotted line). ΓLjj = ΓRa j j ≡ Γ/2 ( j = 1, 2) and pL = pRa = 0.5 in Eq. (9). The frequency of the AC field is ℏω/Γ = 40 and its amplitude is eVAC /Γ = 40. The tunneling coupling between QD1 Ra Rb and lead Rb is (a) ΓRb 11 /(Γ11 + Γ11 ) = 0, (b) 0.4, and (c) 0.7. Note that the abscissa shows −ε0 in all the panels. absence of the AC field.33) 5. Conclusions We calculated the electric current through a single QD and DQD in an AC field by solving the time-dependent Schrödinger equation using the scattering theory. The AC field is considered as an oscillating energy level FAC (t) in Eq. (1) in a classical way. For a single QD, we formulated the PAT when the linewidth Γ due to the tunnel coupling is much smaller than ℏω and adiabatic transport when Γ ≫ ℏω. In the case of PAT, we derived an analytical expression for the electric current, which indicates the resonant tunneling through 17/27 FULL PAPERS J. Phys. Soc. Jpn. the energy levels of polariton, ε0 +Nℏω (N = 0, ±1, ±2, · · · ). In the case of adiabatic transport, the resonant tunneling takes place through the energy level ε(t). For the DQD, we considered the situation that one of the QDs (QD1) is irradiated by an AC field while the other is not (QD2). We examined the PAT in the presence of magnetic flux penetrating between the QDs to elucidate the coherent transport through the polariton states. Using the infinite perturbation series with respect to the tunnel Hamiltonian, we calculated the electric current to the second order in eVAC /(2ℏω) in the two- and three-terminal geometries. We observed the AB effect both in the main peak (N = 0) and in the subpeaks (N , 0). The coherence in the subpeaks can be understood by the intermediate states in the T-matrix depicted in Fig. 4. In the three-terminal geometry, we demonstrated the measurement of the phase shift through QD1. The measured phase shift changes continuously from 0 to π around both the main peak and subpeaks. No phase lapse is observed between the peaks. For the PAT through a single QD, the electric current in Eq. (15) was derived in Refs. 3 and 24 for kB T ≫ Γ and that in Eq. (28) was reported in Ref. 23, using the Keldysh nonequilibrium Green’s function, Floquet theory, etc. Compared with those methods, our calculation method based on the scattering theory is helpful to understand the transport through a timedependent energy level intuitively on one hand, but it is difficult to consider the electron– electron interaction beyond the mean-field level on the other hand. Acknowledgement This work was partially supported by JST SPRING, Grant Number JPMJSP2123, and SUZUKI FOUNDATION. Appendix A: Solution of time-dependent Schrödinger equation For the DQD in Fig. 1(b), the Hamiltonian is given by Eq. (11). The substitution of the wavefunction in Eq. (12) into Eq. (11) yields h ( j) i∗ dC j −iE j (t)/ℏ X X iℏ e = Cα,k (t)e−iεk (t−t0 )/ℏ Vαk , dt α=L,R k iℏ dCα,k −iεk (t−t0 )/ℏ X ( j) e = C j (t)e−iE j (t)/ℏ Vαk . dt j=1,2 Their integration from t = t0 to t0 + T yields h ( j) i∗ Z t0 +T X X Vαk C j (t0 + T ) = C j (t0 ) + Cα,k (t)e−i[εk (t−t0 )−E j (t)]/ℏ dt, iℏ t 0 α=L,R k 18/27 (A·1) (A·2) (A·3) FULL PAPERS J. Phys. Soc. Jpn. Cα,k (t0 + T ) = Cα,k (t0 ) + X V ( j) Z t0 +T αk iℏ j=1,2 C j (t)ei[εk (t−t0 )−E j (t)]/ℏ dt. (A·4) t0 From Eqs. (A·3) and (A·4), we derive the transition rate to the lowest order in HT in Sect. A.1 and the scattering matrix to the infinite order in HT in Sect. A.2. A.1 Sequential tunneling through single QD (2) (2) = 0 and = VRk We examine the single QD model depicted in Fig. 1(a), by setting VLk C2 (t) = 0 in Eqs. (A·3) and (A·4). We begin with the sequential tunneling to the lowest order in HT . We consider the transition of an electron from |d1 ⟩ in the QD at t = t0 to |α, k⟩ in lead α at t = t0 + T . For C1 (t0 ) = 1 and Cα,k (t0 ) = 0, Eq. (A·4) gives (1) Z t0 +T Vαk Cα,k (t0 + T ) ≃ e−i(ε0 −εk )(t−t0 )/ℏ e−iṼAC (sin ωt−sin ωt0 ) dt iℏ t0 ∞ X (1) = Vαk JN (ṼAC )F (ε0 − εk + Nℏω)e−i(Nωt0 −ṼAC sin ωt0 ) (A·5) (A·6) N=−∞ to the first order in HT , where ṼAC = eVAC /(ℏω), JN is the Nth Bessel function, and e−iET /ℏ − 1 . (A·7) E Note that |F (E)|2 = [4 sin2 ET /(2ℏ)]/E 2 shows a peak at E = 0 with the width of 2πℏ/T and F (E) = the height of (T /ℏ)2 . It has an asymptotic form of |F (E)|2 ∼ 2πT δ(E)/ℏ for large T . A.1.1 Case of Γ ≪ ℏω We set T to be the characteristic time of the transport through the QD, T ∼ ℏ/Γ (or several times of ℏ/Γ). Note that the transition from |d1 ⟩ to |α, k⟩ takes place directly by the perturbation HT in Eq. (5) in our model. This is in contrast to the conventional situation of the scattering theory where T → ∞ for an asymptotic transition to the final state by the nonlocal perturbation.22) In the case of Γ ≪ ℏω, (1) |Cα,k (t0 + T )|2 ≃ Vαk 2 Xh i2 JN (ṼAC ) |F (ε0 − εk + Nℏω)|2 , (A·8) N since the peaks of |F (ε0 − εk + Nℏω)| are separated from each other, and thus, the cross2 terms in |Cα,k (t0 + T )|2 (interference among different N’s) can be disregarded. Using the above-mentioned asymptotic form, the transition rate is given by d wQD→α,k = |Cα,k (t0 + T )|2 dT 19/27 FULL PAPERS J. Phys. Soc. Jpn. = i2 2π (1) 2 X h JN (ṼAC ) δ(ε0 − εk + Nℏω), Vαk ℏ N (A·9) which is an extension of the Fermi’s golden rule. As a result, the transition rate from the QD to lead α is γQD→α = X   wQD→α,k 1 − fα (εk ) (A·10) k = i2   Γα X h JN (ṼAC ) 1 − fα (ε0 + Nℏω) , ℏ N (A·11) where fα (E) = [1 + e(E−µα )/(kB T ) ]−1 is the Fermi distribution function in lead α at temperature T . Similarly, the transition rate from lead α to the QD is given by X γα→QD = wα,k→QD fα (εk ) (A·12) k = i2 Γα X h JN (ṼAC ) fα (ε0 + Nℏω). ℏ N (A·13) The master equation for the probabilities P1 for the occupied QD and P0 for the empty QD is given by X X d P1 = −P1 γQD→α + P0 γα→QD , dt α=L,R α=L,R (A·14) and P1 + P0 = 1. In the stationary state (dP1 /dt = 0), the electric current is IL→R = −e[P1 γQD→L − P0 γL→QD ] = e[P1 γQD→R − P0 γR→QD ], (A·15) which yields Eq. (15). A.1.2 Case of Γ ≫ ℏω In the adiabatic case of Γ ≫ ℏω, electrons do not feel the oscillation of the energy level during T ∼ ℏ/Γ. Then, E1 (t) ≃ ε1 (t0 )(t − t0 ) in Eq. (13) for t0 < t < t0 + T , and thus, the electric current flows through the energy level ε1 (t0 ). The same procedure as in the previous subsection yields IL→R (t0 ) =  e ΓL ΓR  fL (ε1 (t0 )) − fR (ε1 (t0 )) . ℏ Γ L + ΓR (A·16) We replace t0 by t in Eq. (17). A.2 Resonant tunneling through single QD Here, we perform the summation of the perturbative series to the infinite order to obtain the exact formula for the electric current in the case of a single QD. Following the scattering 20/27 FULL PAPERS J. Phys. Soc. Jpn. theory,21, 22) we consider an electron of state k in lead L at time t = t0 − T as the initial state, i.e., C1 (t0 − T ) = 0 and Cα,k′ (t0 − T ) = δα,L δk,k′ . We evaluate the scattering matrix S L,k→α,k′ = Cα,k (t0 + T ) (A·17) as an infinite series in HT , using Eqs. (A·3) and (A·4) by the method of successive substitution. When Γ ≪ ℏω, we omit t0 , which is irrelevant to this case. The asymptotic form of F (E) in Eq. (A·7) for large T results in S L,k→α,k′ in Eqs. (19), (20), and (21). The infinite series in Eq. (21) can be summed up analytically, which results in G N,0 (E) in Eq. (25). When Γ ≫ ℏω, E1 (t) ≃ ε1 (t0 )(t − t0 ) in Eq. (13) for t0 < t < t0 + T . The resonant tunneling through the energy level ε1 (t0 ) is derived in the same way. A.3 Resonant tunneling through DQD In the case of the DQD in Figs. 1(b) and 1(c), we consider the PAT for Γ ≪ ℏω only, setting t0 = 0. On the assumption that C1 (−T ) = C2 (−T ) = 0 and Cα,k′ (−T ) = δα,L δk′ ,k in the initial state, we express the scattering matrix, S L,k→α,k′ = Cα,k (T ), by an infinite series of the perturbation in HT , using Eqs. (A·3) and (A·4) by the method of successive substitution. The result is given by Eqs. (19), (34), and (35). Appendix B: Retarded Green’s function and Floquet theory Here, we discuss the case of a single QD for simplicity. The extension to the case of the DQD is straightforward. Consider the retarded Green’s function, Gr (t, t′ ) in Eq. (24), for the time-dependent (2) (2) Hamiltonian in Eq. (2) with ε2 = 0 and VLk = VRk = 0. If we regard it as a function of ta = (t + t′ )/2 and tr = t − t′ , Gr (ta + T, tr ) = Gr (ta , tr ) (B·1) for T = 2π/ω because of the periodicity of the Hamiltonian, H(t + T ) = H(t), in the Floquet theory.41–43) Its Fourier transformation is given by Z ∞ X 1 r ′ G (t, t ) = dEḠ N (E)e−i(Nωta +Etr /ℏ) . 2πℏ N=−∞ We introduce G N,0 (E) in Eq. (21), which is related to Gr (t, t′ ) in Eq. (24) by Z ∞ X 1 ′ r ′ G (t, t ) = dEG N,0 (E)e−i[Nωt+E(t−t )/ℏ] . 2πℏ N=−∞ (B·2) (B·3) A comparison with Eq. (B·2) results in G N,0 (E) = Ḡ N (E + Nℏω/2). 21/27 (B·4) FULL PAPERS J. Phys. Soc. Jpn. ′ Similarly to the unperturbed Green’s function G(0) N,N ′ (E) in Eq. (22), we define G N,N for the propagator of electrons of energy E with N ′ (N) photons before (after) the propagation through the QD. It satisfies G N,N ′ (E) = G N−N ′ ,0 (E + N ′ ℏω) = Ḡ N−N ′ (E + (N + N ′ )ℏω/2). (B·5) Appendix C: Green’s function to second order in ṼAC /2 From Eq. (35), we derive the expression of the Green’s function of the DQD, GN,0 (E), to the second order in ṼAC /2. Using the formula of the Bessel function, J0 (x) = 1 − (x/2)2 + O(x/2)4 , J±1 (x) = ±x/2 + O(x/2)3 , and J±N (x) = O(x/2)N (N ≥ 2), the unperturbed Green’s functions in Eq. (36) are evaluated as G(0) N,N (E) = AN,N (E) + BN,N (E), (C·1) AN,N (E) = diag (gN (E), hN (E)) !2 ṼAC diag (gN−1 (E) + gN+1 (E) − 2g0 (E), 0) BN,N (E) = 2 (C·2) (C·3) for N ′ = N, ṼAC diag (gN (E) − gN+1 (E), 0) 2 for N ′ = N ± 1, and G(0) N,N ′ (E) = 0 otherwise, to the second order in ṼAC /2. Here, (0) G(0) N,N+1 (E) = GN+1,N (E) = 1 , E − ε0 + Nℏω + iη 1 hN (E) = . E − ε2 + Nℏω + iη Substituting Eqs. (C·1) and (C·4) into Eq. (35), we obtain −1  i G0,0 (E) ≃ A0,0 (E) 1 + ΓA0,0 2  −1  −1 i i + 1 + A0,0 (E)Γ B0,0 (E) 1 + ΓA0,0 (E) 2 2   −1 X i i R − 1 + A0,0 (E)Γ G(0) 0,N ′ ΓGN ′ ,0 , 2 N ′ =±1 2  −1  −1 i i G±1,0 (E) ≃ 1 + A±1,±1 (E)Γ G(0) (E) 1 + ΓA (E) . 0,0 ±1,0 2 2 gN (E) = 22/27 (C·4) (C·5) (C·6) (C·7) (C·8) FULL PAPERS J. Phys. Soc. Jpn. Appendix D: Phase shift through QD in the AC field Let us consider the phase shift through QD1 in Fig. 1(c), neglecting the coupling to QD2. In the absence of the AC field, the phase shift of an electron in the transfer from |L, k⟩ to |R, k′ ⟩ is given by the phase of 1 V (1)∗ , (D·1) εk − ε0 + iΓ1 /2 L,k L Rb −1 where Γ1 = Γ11 +ΓRa 11 +Γ11 is the total linewidth in QD1. This phase is equal to tan Γ1 /[2(ε0 − (1) ⟨R, k′ |T |L, k⟩ = VR,k ′ (1) (1)∗ εk )] since VR,k ′ and V L,k are real and positive in our gauge. In the presence of the AC field, the T-matrix is given by Eq. (20) for the electron transfer accompanied by the emission or absorption of |N| photons, with the Green’s function in Eq. (25) if Γ is replaced by Γ1 . To the first order in ṼAC /2, 1 G0,0 (εk ) ≃ (D·2) εk − ε0 + iΓ1 /2 and ! 1 1 ṼAC − G±1,0 (εk ) ≃ ± . (D·3) 2 εk − ε0 + iΓ1 /2 εk − ε0 ± ℏω + iΓ1 /2 To the peak of the differential conductance dIL→Ra /dµL at µL = ε0 + Nℏω (N = 0, ±1), ⟨R, k′ |T −N |L, k⟩ mainly contributes when ℏω ≫ Γ1 and ṼAC = eVAC /(ℏω) is small. Hence, the phase shift around the peak is dominantly determined by the phase of G0,0 (εk ) in Eq. (D·2) for N = 0 and by that of the second term in G−N,0 (εk ) in Eq. (D·3) for N = ±1. This yields the same phase shift as in the absence of the AC field if the origin of ε0 is shifted by Nℏω. In the transport experiment, the measured phase shift should be identical to θQD in Eq. (38) if the coupling to QD2 is negligibly small. In general, if Γ1 and ε0 in Eq. (38) were replaced by the renormalized values due to the coupling to QD2, ϕmax would almost coincide with θQD , as discussed previously in the case without the AC field.33) 23/27 FULL PAPERS J. Phys. Soc. Jpn. References 1) A. H. Dayem and R. J. Martin. Quantum Interaction of Microwave Radiation with Tunneling Between Superconductors. Phys. Rev. Lett., Vol. 8, pp. 246–248, 1962. 2) P. K. Tien and J. P. Gordon. Multiphoton Process Observed in the Interaction of Microwave Fields with the Tunneling between Superconductor Films. Phys. Rev., Vol. 129, pp. 647–651, 1963. 3) G. Platero and R. Aguado. Photon-assisted transport in semiconductor nanostructures. Phys. Rep., Vol. 395, pp. 1–157, 2004. 4) L. P. Kouwenhoven, C. M. Marcus, P. L. McEuen, S. Tarucha, R. M. Westervelt, and N. S. Wingreen, in Mesoscopic Electron Transport, ed. L. L. Sohn, L. P. Kouwenhoven, and G. Schön (Springer, Dordrecht, 1997) NATO Science Series E: Applied Sciences, Vol. 345, p. 105. 5) L. P. Kouwenhoven, S. Jauhar, K. McCormick, D. Dixon, P. L. McEuen, Yu. V. Nazarov, N. C. van der Vaart, and C. T. Foxon. Photon-assisted tunneling through a quantum dot. Phys. Rev. B, Vol. 50, pp. 2019(R)–2022(R), 1994. 6) L. P. Kouwenhoven, S. Jauhar, J. Orenstein, P. L. McEuen, Y. Nagamune, J. Motohisa, and H. Sakaki. Observation of Photon-Assisted Tunneling through a Quantum Dot. Phys. Rev. Lett., Vol. 73, pp. 3443–3446, 1994. 7) R. H. Blick, R. J. Haug, D. W. van der Weide, K. von Klitzing, and K. Eberl. Photonassisted tunneling through a quantum dot at high microwave frequencies. Appl. Phys. Lett., Vol. 67, pp. 3924–3926, 1995. 8) T. Fujisawa and S. Tarucha. Photon assisted tunnelling in single and coupled quantum dot systems. Superlattices Microstruct., Vol. 21, pp. 247–254, 1997. 9) T. H. Oosterkamp, L. P. Kouwenhoven, A. E. A. Koolen, N. C. van der Vaart, and C. J. P. M. Harmans. Photon Sidebands of the Ground State and First Excited State of a Quantum Dot. Phys. Rev. Lett., Vol. 78, pp. 1536–1539, 1997. 10) T. H. Oosterkamp, T. Fujisawa, W. G. van der Wiel, K. Ishibashi, R. V. Hijman, S. Tarucha, and L. P. Kouwenhoven. Microwave spectroscopy of a quantum-dot molecule. Nature, Vol. 395, pp. 873–876, 1998. 11) Y. Kawano, T. Fuse, S. Toyokawa, T. Uchida, and K. Ishibashi. Terahertz photonassisted tunneling in carbon nanotube quantum dots. J. Appl. Phys., Vol. 103, p. 034307, 2008. 24/27 FULL PAPERS J. Phys. Soc. Jpn. 12) K. Shibata, A. Umeno, K. M. Cha, and K. Hirakawa. Photon-Assisted Tunneling through Self-Assembled InAs Quantum Dots in the Terahertz Frequency Range. Phys. Rev. Lett., Vol. 109, p. 077401, 2012. 13) K. Yoshida, K. Shibata, and K. Hirakawa. Terahertz Field Enhancement and PhotonAssisted Tunneling in Single-Molecule Transistors. Phys. Rev. Lett., Vol. 115, p. 138302, 2015. 14) L. J. Geerligs, V. F. Anderegg, P. A. M. Holweg, J. E. Mooij, H. Pothier, D. Esteve, C. Urbina, and M. H. Devoret. Frequency-locked turnstile device for single electrons. Phys. Rev. Lett., Vol. 64, pp. 2691–2694, 1990. 15) L. P. Kouwenhoven, A. T. Johnson, N. C. van der Vaart, C. J. P. M. Harmans, and C. T. Foxon. Quantized current in a quantum-dot turnstile using oscillating tunnel barriers. Phys. Rev. Lett., Vol. 67, pp. 1626–1629, 1991. 16) J. P. Pekola, O.-P. Saira, V. F. Maisi, A. Kemppinen, M. Möttönen, Y. A. Pashkin, and D. V. Averin. Single-electron current sources: Toward a refined definition of the ampere. Rev. Mod. Phys., Vol. 85, pp. 1421–1472, 2013. 17) B. Kaestner and V. Kashcheyevs. Non-adiabatic quantized charge pumping with tunable-barrier quantum dots: a review of current progress. Rep. Prog. Phys., Vol. 78, No. 10, p. 103901, 2015. 18) Y. Zhang, K. Shibata, N. Nagai, C. Ndebeka-Bandou, G. Bastard, and K. Hirakawa. Terahertz Intersublevel Transitions in Single Self-Assembled InAs Quantum Dots with Variable Electron Numbers. Nano Lett., Vol. 15, pp. 1166–1170, 2015. 19) H. Walther, B. T. H. Varcoe, B.-G. Englert, and T. Becker. Cavity quantum electrodynamics. Rep. Prog. Phys., Vol. 69, p. 1325, 2006. 20) A. Reiserer and G. Rempe. Cavity-based quantum networks with single atoms and optical photons. Rev. Mod. Phys., Vol. 87, pp. 1379–1418, 2015. 21) A. C. Hewson. The Kondo Problem to Heavy Fermions. Cambridge Studies in Magnetism. Cambridge University Press, Cambridge, U.K., 1993. 22) J. J. Sakurai and J. Napolitano. Modern Quantum Mechanics. Cambridge University Press, Cambridge, U.K., 2021. 23) A.-P. Jauho, N. S. Wingreen, and Y. Meir. Time-dependent transport in interacting and noninteracting resonant-tunneling systems. Phys. Rev. B, Vol. 50, pp. 5528–5544, 1994. 25/27 FULL PAPERS J. Phys. Soc. Jpn. 24) S. Kohler, J. Lehmann, and P. Hänggi. Driven quantum transport on the nanoscale. Phys. Rep., Vol. 406, pp. 379–443, 2005. 25) A. W. Holleitner, C. R. Decker, H. Qin, K. Eberl, and R. H. Blick. Coherent Coupling of Two Quantum Dots Embedded in an Aharonov-Bohm Interferometer. Phys. Rev. Lett., Vol. 87, p. 256802, 2001. 26) T. Hatano, M. Stopa, W. Izumida, T. Yamaguchi, T. Ota, and S. Tarucha. Gate-voltage dependence of inter dot coupling and Aharanov–Bohm oscillation in laterally coupled vertical double dot. Physica E, Vol. 22, pp. 534–537, 2004. 27) B. Kubala and J. König. Flux-dependent level attraction in double-dot Aharonov-Bohm interferometers. Phys. Rev. B, Vol. 65, p. 245301, 2002. 28) Z.-M. Bai, M.-F. Yang, and Y.-C. Chen. Effect of inhomogeneous magnetic flux on double-dot Aharonov–Bohm interferometer. J. Phys.: Condens. Matter, Vol. 16, No. 12, p. 2053, 2004. 29) H. Lu, R. Lu, and B. Zhu. Fano effect through parallel-coupled double Coulomb islands. J. Phys.: Condens. Matter, Vol. 18, No. 39, p. 8961, 2006. 30) Y. Tokura, H. Nakano, and T. Kubo. Interference through quantum dots. New J. Phys., Vol. 9, p. 113, 2007. 31) F. Li, H. J. Jiao, H. Wang, J. Y. Luo, and X.-Q. Li. Coulomb blockade double-dot Aharonov–Bohm interferometer: Harmonic decomposition of the interference pattern. Physica E, Vol. 41, pp. 521–524, 2009. 32) R. Härtle, G. Cohen, D. R. Reichman, and A. J. Millis. Decoherence and lead-induced interdot coupling in nonequilibrium electron transport through interacting quantum dots: A hierarchical quantum master equation approach. Phys. Rev. B, Vol. 88, p. 235426, 2013. 33) Y. Zhang, R. Sakano, and M. Eto. Kondo Effect and Phase Measurement in Double Quantum Dot in Parallel. J. Phys. Soc. Jpn., Vol. 91, No. 1, p. 014703, 2022. 34) A. Yacoby, M. Heiblum, D. Mahalu, and H. Shtrikman. Coherence and Phase Sensitive Measurements in a Quantum Dot. Phys. Rev. Lett., Vol. 74, pp. 4047–4050, 1995. 35) R. Schuster, E. Buks, M. Heiblum, D. Mahalu, V. Umansky, and H. Shtrikman. Phase measurement in a quantum dot via a double-slit interference experiment. Nature, Vol. 385, pp. 417–420, 1997. 26/27 FULL PAPERS J. Phys. Soc. Jpn. 36) W. G. van der Wiel, S. De Franceschi, T. Fujisawa, J. M. Elzerman, S. Tarucha, and L. P. Kouwenhoven. The Kondo Effect in the Unitary Limit. Science, Vol. 289, pp. 2105–2108, 2000. 37) Y. Ji, M. Heiblum, D. Sprinzak, D. Mahalu, and H. Shtrikman. Phase Evolution in a Kondo-Correlated System. Science, Vol. 290, pp. 779–783, 2000. 38) S. Takada, C. Bäuerle, M. Yamamoto, K. Watanabe, S. Hermelin, T. Meunier, A. Alex, A. Weichselbaum, J. von Delft, A. Ludwig, A. D. Wieck, and S. Tarucha. Transmission Phase in the Kondo Regime Revealed in a Two-Path Interferometer. Phys. Rev. Lett., Vol. 113, p. 126601, 2014. 39) M. Avinun-Kalish, M. Heiblum, O. Zarchin, D. Mahalu, and V. Umansky. Crossover from ‘mesoscopic’ to ‘universal’ phase for electron transmission in quantum dots. Nature, Vol. 436, pp. 529–533, 2005. 40) C. Karrasch, T. Hecht, A. Weichselbaum, Y. Oreg, J. von Delft, and V. Meden. Mesoscopic to Universal Crossover of the Transmission Phase of Multilevel Quantum Dots. Phys. Rev. Lett., Vol. 98, p. 186802, 2007. 41) G. Floquet. Sur les équations différentielles linéaires à coefficients périodiques. Ann. Sci. Ec. Norm. Super., Vol. 12, pp. 47–88, 1883. 42) L. H. Eliasson. Floquet solutions for the 1-dimensional quasi-periodic Schrödinger equation. Commun. Math. Phys., Vol. 146, pp. 447–482, 1992. 43) H. Ishizuka and N. Nagaosa. Local photo-excitation of shift current in noncentrosymmetric systems. New J. Phys., Vol. 19, p. 033015, 2017. 44) T. Kubo, Y. Tokura, T. Hatano, and S. Tarucha. Electron transport through AharonovBohm interferometer with laterally coupled double quantum dots. Phys. Rev. B, Vol. 74, p. 205310, 2006. 45) M. Eto and R. Sakano. Fano-Kondo resonance versus Kondo plateau in an AharonovBohm ring with an embedded quantum dot. Phys. Rev. B, Vol. 102, p. 245402, 2020. 46) In Fig. 8(a) with ε2 − µL = 70Γ, ϕmax changes abruptly (gradually) around a subpeak at ε0 − µL = −ℏω (ℏω). If we choose ε2 − µL = −70Γ, ϕmax changes abruptly (gradually) around a subpeak at ε0 − µL = ℏω (−ℏω). 27/27