Efficient green light-emitting diodes based on quasi-two-dimensional composition and phase engineered perovskite with surface passivation.

Yang X, Yang X, Zhang X, Deng J, Chu Z, Jiang Q, Meng J, Wang P, Zhang L, Yin Z, You J. · 2018

Read Efficient green light-emitting diodes based on quasi-two-dimensional composition and phase engineered perovskite with surface passivation. by Yang X, Yang X, Zhang X, Deng J, Chu Z, Jiang Q, Meng J, Wang P, Zhang L, Yin Z, You J. (2018) in the Tower of Babel, a free online library of public-domain works preserved in clean, searchable text. No sign-up. The full text is served as a plain-text file at a predictable URL, where text is present: https://antarctic-labs.com/tower-of-babel/europmc-pmc5805756.txt.

Introduction

Yang and co-authors build a brighter green LED from layered perovskite. Perovskite diodes emit sharp, pure colors. Mixed phases and surface flaws waste their light. The team tackles both flaws at once.

First they tune the mix to favor the best layered phases. Then they coat the film with a small organic molecule called TOPO, to heal surface defects. Their green diodes reach a current efficiency of 62.4 candelas per amp. External quantum efficiency hits 14.36 percent. Readers get a recipe that joins phase control with surface care for better and brighter light devices.

Catalog record

CREATORYang X, Yang X, Zhang X, Deng J, Chu Z, Jiang Q, Meng J, Wang P, Zhang L, Yin Z, You J.
YEAR2018
COLLECTIONPAPERS
FORMATTXT
FILE SIZE37 KB
LICENSECC BY 4.0
RIGHTSCC BY
SOURCEEurope PMC

Source: https://europepmc.org/articles/PMC5805756

Browse the full library · About the Tower of Babel

Full text

The opening of the work, from the library's hosted text:

Efficient green light-emitting diodes based on quasi-two-dimensional composition and phase engineered perovskite with surface passivation By Xiaolei Yang, Xingwang Zhang, Jinxiang Deng, Zema Chu, Qi Jiang, Junhua Meng, Pengyang Wang, Liuqi Zhang, Zhigang Yin, Jingbi You Published in: Nature Communications DOI: 10.1038/s41467-018-02978-7 ABSTRACT Abstract Perovskite light-emitting diodes (LEDs) are attracting great attention due to their efficient and narrow emission. Quasi-two-dimensional perovskites with Ruddlesden–Popper-type layered structures can enlarge exciton binding energy and confine charge carriers and are considered good candidate materials for efficient LEDs. However, these materials usually contain a mixture of phases and the phase impurity could cause low emission efficiency. In addition, converting three-dimensional into quasi-two-dimensional perovskite introduces more defects on the surface or at the grain boundaries due to the reduction of crystal sizes. Both factors limit the emission efficiency of LEDs. Here, firstly, through composition and phase engineering, optimal quasi-two-dimensional perovskites are selected. Secondly, surface passivation is carried out by coating organic small molecule trioctylphosphine oxide on the perovskite thin film surface. Accordingly, green LEDs based on quasi-two-dimensional perovskite reach a current efficiency of 62.4 cd A−1 and external quantum efficiency of 14.36%. INTRODUCTION Solution-processed halide perovskite semiconductor materials show good photoluminescence quantum yields (PLQYs)1–7, which motivates applications in displays and lighting8. The perovskite light-emitting diodes (PeLEDs) have been reported with moderate electroluminescence (EL) efficiencies as well9–15. Their external quantum efficiencies (EQEs) have reached about 10% for near-infrared13–15 and also in green emission11,12,15. Hybrid organic–inorganic perovskites are better known for their free charge carriers with long diffusion length, which is good for solar cells. However, opposite properties are desired when they are used as emitting materials in LEDs11,16–18. The idea is to spatially confine charges with the insulating layers, and thus the exciton dissociation is suppressed and the radiative recombination can be enhanced in the perovskite films. Several efficient methods have been adopted, including polymer composite19, nanocrystal pinning11 and quantum dots3–7. The exciton binding energy is enlarged in the two-dimensional (2D) perovskite and thus the emission efficiency can be enhanced20,21. In the early reports, 2D perovskite materials were used as emitting layers, while electroluminescence can only be observed at liquid nitrogen temperature20. Recently, quasi-two-dimensional (quasi-2D) perovskites have been proposed by doping 2D perovskites into three-dimensional (3D) perovskite structures. The initial idea was to enhance the humidity stability of perovskite solar cells22–24. More recently, it was found that multiple quantum wells could be assembled in these quasi-2D perovskites13,14, which can facilitate the formation of exciton and reduce the possibility of exciton dissociation. This makes the quasi-2D perovskite an efficient luminescent material13–15,25. The working mechanism of quasi-2D PeLEDs has been fully discussed elsewhere13,14. Electrons and holes injected from large bandgap phases (small n-phase) can rapidly transfer into small bandgap phases (large n-phase), then electrons and holes recombine in large n-phase and emit as photons. The EQEs of quasi-2D perovskite LEDs have achieved around 10%13,14 and highest EQE of 11.7% in near-infrared region was obtained14. Comparing to organic or inorganic LED counterparts26,27, there is still room for improvement in the EQE. It is known that quasi-2D perovskite materials usually contain a mixture of phases and the phase impurity could lead to low emission efficiency, and thus fine control of the composition/phases is critical for efficient emission. In addition, solution processed thin films of quasi-2D perovskite show reduced crystal size compared to those of 3D perovskite13,15. This could increase the concentration of the defects and traps on the film surface and grain boundaries, which will act as non-radiative recombination centers and thus decrease the emission efficiency. Surface passivation has been proved an efficient way for reducing the defects in perovskite solar cells28–30. In this article, PEA2(FAPbBr3)n-1PbBr4 (n = 1, 2, …, ∞) is investigated as the emitting layer for quasi-2D perovskite LEDs, where PEA and FA are phenylethylammonium (C6H5C2H4NH3+) and formamidinium (HC(NH2)2+), respectively. Firstly, we optimize the films phase engineering/phase engineering. We find that the perovskite with n = 3 composition shows decent phases and the obtained films show the highest photoluminescence (PL) yield. Secondly, we present surface passivation of quasi-2D perovskite films by trioctylphosphine oxide (TOPO) treatment31. Accordingly, the PeLEDs based on PEA2(FAPbBr3)n-1PbBr4 with n = 3 composition show green emission with current efficiency (CE) of 62.4 cd A−1 and EQE of 14.36%, which is the highest efficiency for PeLEDs reported so far. RESULTS Properties of quasi-2D perovskite with different compositions The schematics of n-phase PEA2(FAPbBr3)n-1PbBr4 are drawn in Fig.1a, illustrating that the n-phase unit cell contains n-1 sheets of PbBr6-octahedra and two PEA tiers. The perovskite films are prepared by spin-coating a precursor solution using a crystal-pinning process11,32. Their compositions are controlled by the ratio PEABr:FABr:PbBr2 (Supplementary Table 1), and compositions n ranging from 2 to 6 are discussed. Previous results suggested that the quasi-2D perovskite films are not a single phase but contain a variety of n-phases13,14. For example, if the precursor solution with n = 2 composition is spin-coated, the generated films might include n = 2 phase but could also contain other phases such as n = 1 or n ≥ 3. To avoid misunderstanding, we distinguish the composition and phase by n-composition and n-phase, respectively. Methylammonium chloride (MACl) is also added into the precursor to improve the morphology and enhance the emission efficiency of the formed films (Supplementary Figs. 1, 2 and 12), but most MACl escape from the film during annealing33. The role of MACl has been well investigated in solar cells33,34. First, the MACl can slow down perovskite crystallization and improve film morphology. Second, the incorporation of a very small amount of elemental Cl could passivate the grain boundary, and then enhance the emission efficiency (Supplementary Fig. 2). [Figure: Properties of perovskite films with different compositions. a Scheme of PEA2(FAPbBr3)n-1PbBr4 phases. The black part is PEA, the blue square is PbBr6-octahedron and the gray dot is FA. b X-ray diffraction patterns of PEA2(FAPbBr3)n-1PbBr4 films with different n-compositions. Diffraction patterns of n = 1 phase (black vertical lines), n = 2 phase (pink vertical lines) and n = ∞ phase (marked with (100)) were labeled. The analysis details can be found in the Supplementary Table 2. c Photoluminescence of PEA2(FAPbBr3)n-1PbBr4 with different n-compositions. d Photoluminescence intensity and peak of PEA2(FAPbBr3)n-1PbBr4 films with different compositions with the data collected from c. e Photoluminescence image of PEA2(FAPbBr3)n-1PbBr4 films with different compositions under ultraviolet lamp excitation. Figure 1a adapted from ref. 13 (copyright 2016 Macmillan Publishers)] X-ray diffraction (XRD) measurements are carried out to determine the accurate phases in our obtained quasi-2D perovskite films. As shown in Fig. 1b, all the perovskite films with n ≥ 2 compositions show diffraction peaks at 14.8°, which is the same as the (100) diffraction patterns of the 3D perovskite FAPbBr3 (refs. 7,35). However, the peaks become much more broadened, indicating that the diffraction peak could be from a series of PEA2(FAPbBr3)n-1PbBr4 phases with large n (n→∞) or 3D FAPbBr3 with nano-size grains (Supplementary Fig.3)15. This result shows that all the quasi-2D perovskite films always contain large n-phases (n→∞) or 3D perovskite regardless of the composition of the precursor. Atomic force microscopy (AFM) images confirm the reduction of the crystal size during the transformation of 3D perovskite into quasi-2D perovskites (Supplementary Fig.3). In addition to the diffraction peak at 14.8°, a

Read the complete text