Load Data for Mk279 Projectiles
Winter, Kyle Oakley, Torres, Sivana Mirhai · 2025
Read Load Data for Mk279 Projectiles by Winter, Kyle Oakley, Torres, Sivana Mirhai (2025) in the Tower of Babel, a free online library of public-domain works preserved in clean, searchable text. No sign-up. The full text is served as a plain-text file at a predictable URL, where text is present: https://antarctic-labs.com/tower-of-babel/doe-osti-3002999-load-data-for-mk279-projectiles.txt.
Introduction
Kyle Winter and Sivana Torres collect firing data in Sandia report SAND2025-13958, printed November 2025. The data cover Mk279 Mod1 projectiles shot from an RD24 barrel at different powder loads. The goal is a reference table: future testers who use this projectile as a calibrated impactor can pick a load to reach a target speed.
Tables pair each powder charge with the measured average velocity. The authors flag a limit plainly: the shot count at each load was too small for the averages to be statistically firm. More shots per load are needed before the numbers carry high confidence. The short report is a working lab record, published so later ballistic test planning starts from measured data rather than fresh trial and error.
Catalog record
| CREATOR | Winter, Kyle Oakley, Torres, Sivana Mirhai |
|---|---|
| YEAR | 2025 |
| COLLECTION | PAPERS |
| FORMAT | TXT |
| FILE SIZE | 8 KB |
| LICENSE | Public Domain |
| RIGHTS | PUBLIC DOMAIN |
| SOURCE | DOE OSTI |
Browse the full library · About the Tower of Babel
Full text
The opening of the work, from the library's hosted text:
SAND2025-13958 SANDIA REPORT SAND2025-13958 Printed November 2025 Load Data for Mk279 Projectiles Kyle Winter & Sivana Torres Prepared by Sandia National Laboratories Albuquerque, New Mexico 87185 Livermore, California 94550 Issued by Sandia National Laboratories, operated for the United States Department of Energy by National Technology & Engineering Solutions of Sandia, LLC. NOTICE: This report was prepared as an account of work sponsored by an agency of the United States Government. Neither the United States Government, nor any agency thereof, nor any of their employees, nor any of their contractors, subcontractors, or their employees, make any warranty, express or implied, or assume any legal liability or responsibility for the accuracy, completeness, or usefulness of any information, apparatus, product, or process disclosed, or represent that its use would not infringe privately owned rights. Reference herein to any specific commercial product, process, or service by trade name, trademark, manufacturer, or otherwise, does not necessarily constitute or imply its endorsement, recommendation, or favoring by the United States Government, any agency thereof, or any of their contractors or subcontractors. The views and opinions expressed herein do not necessarily state or reflect those of the United States Government, any agency thereof, or any of their contractors. Printed in the United States of America. This report has been reproduced directly from the best available copy. Available to DOE and DOE contractors from U.S. Department of Energy Office of Scientific and Technical Information P.O. Box 62 Oak Ridge, TN 37831 Telephone: (865) 576-8401 Facsimile: (865) 576-5728 E-Mail: [email protected] Online ordering: http://www.osti.gov/scitech Available to the public from U.S. Department of Commerce National Technical Information Service 5301 Shawnee Road Alexandria, VA 22312 Telephone: (800) 553-6847 Facsimile: (703) 605-6900 E-Mail: [email protected] Online order: https://classic.ntis.gov/help/order-methods NT OF E ME N RT ER A DEP GY • • IC A U NIT ER ED ST M A TES OF A 2 ABSTRACT This document details the resulting velocity of Mk279 Mod1 projectiles when fired from a RD24 barrel with between 15 and 110 grains of smokeless propellant to achieve velocities between 163 and 651m/s. 3 This page intentionally left blank. 4 1. LOAD DATA FOR MK279 PROJECTILES 1.1. Introduction The Mk279 Mod1 is a projectile designed to be fired from the RD24 disruptor barrel. The objective of this work was to determine the velocity of the MK279 when loaded with different amount of propellant. The Mk279 Mod1 has a 12 gauge diameter, 0.73 inches (18.5mm), with a steel core and copper plating 0.006 inches (0.15mm) thick and is shown in Figure 1-1. It has a mass of 1.8oz (51g). The maximum propellant load for this series was 110 grains of powder. The propellant was a dual powder load made up of approximately 20 grains of Alliant Unique and approximately 90 grains of ST Marks OBP502. (a) (b) (c) (d) Figure 1-1. Mk279 Mod1 projectile 1.2. Experimental Setup The following experiments were conducted at Thunder Range one of Sandia National Laboratories’ explosive test sites. The experimental setup consisted of a RD24 barrel aimed perpendicular to two high speed cameras. The two cameras were setup to be redundant data collect and the cameras were placed perpendicular to each other. The cameras were calibrated for distance by recording a known distance, ruler, along the flight path to determine a distance calibration for each camera. The RD24 was electrically fired and was mounted in a recoil absorbing stand, see Figure 1-2. The experimental procedure involved loading a primed shotshell hull with the designated amount of powder followed by a Mk279 Mod1 projectile. The loaded shell was fired, and the resulting projectile velocity was determined using high speed imaging data. All powder loads were achieved by first adding the Unique powder up to 20 grains and then adding OBP502 to reach the final propellant mass. For propellant masses below 20 grains, only Unique powder was used. Cardboard 5 Figure 1-2. RD24 barrel in test stand or felt wadding was added between the powder and projectile to account for the difference in volume between all the loads. High speed video was captured of the projectile motion and the velocity of the projectiles was determined using the high speed images. The velocity for each shot was determined using an custom MATLAB script. The script first generated a "synthetic" streak image by extracting a single row of pixels from every image in a data set (black line in Figures 1-3) and stacking them vertically downward such that time is on the y axis and distance is on the x-axis. As such, the inverse of the slope of the projectile path is the projectiles velocity. A line was then fit to the streak image using the polyfit MATLAB function, Figure 1-4, and the slope of the fitted line used to determine the projectile velocity. 6 (a) (b) (c) (d) Figure 1-3. a-c: Example high speed images with extracted pixel line indicated. d: Resultant streak image 7 (a) (b) Figure 1-4. a: Example of line fit to streak image and b) resulting data. 8 1.3. Results Table 1.3 shows the load data gathered in the present work. The first column is the powder load in grains, second is the shot ID for internal reference, the third column is the velocity of the shot determined using the automated process outlined in Figures 1-3 and 1-4. The last column lists the average velocity for that powder load determined as the arithmetic mean rounded to the nearest whole number. The uncertainty in the mean is the difference between the mean and maximally different velocity. The velocity values are plotted in Figure 1-5 along with a polynomial curve fit with polynomial values and R2 value. Figure 1-5. Plot of velocity data as a function of total powder load. The data are fit to a polynomial which is plotted and the polynomial and R2 values shown. 9 MK279 Mod1 Load Data Load (Grains) Shot ID Velocity (m/s) Average Velocity (m/s) VS8 163 15 163 ± 0 VS10 163 VS15 192 17 191 ± 1 VS17 189 VS18 212 VS19 212 18.5 DS10 212 215 ± 18 DS11 206 DS12 233 VS12 229 VS13 236 VS14 232 20 240 ± 22 DS16 224 DS17 262 DS18 256 VS6 293 VS7 278 25 DS5 267 278 ± 15 DS6 285 DS9 266 VS5 339 VS16 337 35 DS13 342 329 ± 18 DS14 315 DS15 311 VS3 451 VS4 457 DS1 441 DS2 491 60 458 ± 33 DS3 481 DS4 455 DS7 440 DS8 445 VS1 545 80 552 ± 6 VS2 558 DS19 640 110 DS20 657 651 ± 11 DS21 656 10 1.4. Conclusion This report collects ongoing load development data for Mk279 Mod1 projectiles when fired from a RD24 barrel. These data are collected to facilitate future work using the Mk279 Mod1 projectiles as a characterized ballistic impactor by acting as a reference for future test planning. The number of shots at each powder load was not large enough for the average velocities to be considered statistically significant. Additional shots at each powder load are required to achieve a high level of confidence in the reported average velocities. 11 DISTRIBUTION Email—Internal Name Org. Sandia Email Address Kyle Winter 06647 [email protected] Technical Library 1911 [email protected] 12 This