Macro-micro multiscale modeling to assist the design of HPDC Al castings microstructure and alloys for EV super-large body structures (Phase 1)

Hu, Xiaohua, Li, Me, Huo, Yang et al. · 2025

Read Macro-micro multiscale modeling to assist the design of HPDC Al castings microstructure and alloys for EV super-large body structures (Phase 1) by Hu, Xiaohua, Li, Me, Huo, Yang et al. (2025) in the Tower of Babel, a free online library of public-domain works preserved in clean, searchable text. No sign-up. The full text is served as a plain-text file at a predictable URL, where text is present: https://antarctic-labs.com/tower-of-babel/doe-osti-2999833-macro-micro-multiscale-modeling-to-assis.txt.

Introduction

Xiaohua Hu of Oak Ridge National Laboratory, with Mei Li, Yang Huo and Ford Motor Company partners, reports phase one of CRADA NFE-22-09101 in ORNL/TM-2025/4011, dated October 2025. Carmakers want giant one-piece aluminium body castings for electric vehicles, made by high-pressure die casting. Such parts must be strong and must survive self-piercing riveting, the fast joining method of high-volume plants, without cracking.

The team extended a macro-micro computer model that links the whole part down to its crystal-scale structure. Large models find where failure will start and record the strain history there. Small models then rebuild that spot grain by grain, dendrites and silicon-rich regions included. The framework was calibrated against tensile tests, nano-indentation and bending data for the Aural-5 alloy. It reproduced the measured clinch failure point well. Success could let makers skip costly heat treatment when designing such castings.

Catalog record

CREATORHu, Xiaohua, Li, Me, Huo, Yang et al.
YEAR2025
COLLECTIONPAPERS
FORMATTXT
FILE SIZE61 KB
LICENSEPublic Domain
RIGHTSPUBLIC DOMAIN
SOURCEDOE OSTI

Source: https://www.osti.gov/biblio/2999833

Browse the full library · About the Tower of Babel

Full text

The opening of the work, from the library's hosted text:

ORNL/TM-2025/4011 CRADA Final Report/ NFE-22-09101 Macro-micro multiscale modeling to assist the design of HPDC Al castings microstructure and alloys for EV super-large body structures Xiaohua Hu Mei Li (Ford) Yang Huo (Ford) Yang Li (Ford) Garret Huff (Ford) CRADA FINAL REPORT NFE-22-09101 October 2025 Approved for Public Release Distribution is Unlimited ORNL IS MANAGED BY UT-BATTELLE LLC FOR THE US DEPARTMENT OF ENERGY DOCUMENT AVAILABILITY Online Access: US Department of Energy (DOE) reports produced after 1991 and a growing number of pre-1991 documents are available free via https://www.osti.gov. The public may also search the National Technical Information Service’s National Technical Reports Library (NTRL) for reports not available in digital format. DOE and DOE contractors should contact DOE’s Office of Scientific and Technical Information (OSTI) for reports not currently available in digital format: US Department of Energy Office of Scientific and Technical Information PO Box 62 Oak Ridge, TN 37831-0062 Telephone: (865) 576-8401 Fax: (865) 576-5728 Email: [email protected] 1. ABSTRACT Implementation of High Pressure Die Casting (HPDC) Aluminum (Al) body structures for high volume electrified vehicles (EV) to improve electric efficiency remains a key strategy within many original equipment manufacturers (OEM)s. In addition to high strength for safety requirements, superior Self- Piercing Riveting (SPR) performance is demanded for HPDC Al alloys to be compatible with high volume SPR joining. In this work, it is proposed to extend and validate an existing Contractor finite element multiscale macro-micro modeling approach to quantify the influence of the microstructure of HPDC alloys on the fracture strain/displacement under 3-point bend and clinch testing. The success of this work will allow to replace solution treatment stage with low energy consumption heat treatment (HT) processes, or to design new non heat treatable (NHT) HPDC Al alloys to eliminate HT requirements. Ultimately, this project will facilitate the application of HPDC Al alloys for super-large vehicle structures to significantly reduce vehicle weight and thus improving energy efficiency. The purpose of this project is to extend and validate an existing finite element code, which is based on the Contractor developed macro-micro multi-scale modeling approach, to numerically simulate the three-point bending and clinch test and study the influences of material microstructural characteristics and phase properties on rivetability. The macro-micro modeling approach begins with a sample scale model to identify the location mostly prone to failure and obtain the deformation history of the boundaries of that location. The calculated deformation history will then be used to drive a microstructure-based macro-models where the material microstructure and microscale properties are considered. The project began with phase I effort of building a framework of macro-micro three point (3-P) bending test and clinch test of Aural-5 HPDC Al alloy (Al7SiMgMn) in both as-cast and e-coated conditions. In the phase I work which has just been completed, the macro-micro modeling frameworks have been constructed for both the 3-P bending and clinch tests and applied to the Aural-5 HPDC alloy plates with 2.9mm thickness in both conditions. The tensile tests of the alloys in both conditions were obtained and flow behavior extracted were then used in the macro and micro model. The microstructures of the as-cast alloy were characterized and used in the micro-model construction. The microstructures consist of primary Al- dendrites and Al/Si eutectics. The e-coating process will not influence the microstructures but promotes the nano-precipitates formation in the Al-dendrites. The 3-P bending tests of the alloys in both conditions were performed to be used to calibrate the fracture strains of both the Al-dendrites and Al/Si eutectics in the aural-5 alloys in both as-cast and e-coated conditions. The clinch test of only the e-coated aural-5 was performed. The fracture strains determined from the 3-P bending tests and modeling for the e-coated alloys is applied to the micro-model of the clinch test and simulation calculated critical displacement is within the range of data of experimental measurements. The phase II project effort involved the utilization of the knowledge learned in phase I to establish the quantitative correlation between the microstructure characteristics and the riveting performance, which will be further used to guide the optimization of HPDC Al alloy microstructure with different casting conditions and e-coating process to achieve sufficient rivetability to join large thin-wall HPDC alloys. 2. STATEMENT OF OBJECTIVES The purpose of this project is to extend and validate an existing finite element code, which is based on the Contractor developed macro-micro multi-scale modeling approach, to numerically simulate the three-point bending and clinch test and study the influences of material microstructural characteristics and phase properties on the rivetability. The macro-micro modeling approach begins with a sample scale model and identify the location, which is mostly prone to failure, the deformation history of the boundaries of that location calculated will be used to drive a microstructure-based sub-models where the material microstructure and microscale properties are considered. Using this approach, the wrap-bending failure for two Al alloys are correctly predicted for the first time. 5 The project began with a phase I effort of building a framework of macro-micro three point bending test and clinch test of Al7SiMgMn HPDC alloy in the as-cast and e-coated conditions. Those results will then be validated with experimental test results. The phase II effort involved the utilization of the knowledge learned in phase I to establish the quantitative correlation between the microstructure characteristics and the riveting performance, which will be further used to guide the optimization of HPDC Al alloy microstructure using heat treatment process to achieve sufficient rivetability to join large thin-wall HPDC alloys. 3. BENEFITS TO THE FUNDING DOE OFFICE’S MISSION The project will ensure accurate prediction of the microstructure effects on bendability and rivetability of super large die cast (SLDC) Al alloys, giving guidance to the process optimization of the SLDC process to reach the department of energy goal considerable vehicle light-weighting and cost-cutting and promote the EV adoption and substantial decarbonization. 4. TECHNICAL DISCUSSION OF THE WORK PERFORMED BY ALL PARTIES In order to most effectively and efficiently meet the project objectives outlined above, the team established a phase -I project plan with four tasks (1-3) with phase-II project plan with additional four tasks (4-7) 1) Alloy selection and microstructure characterizations 2) Tension, 3-point bending and clinch Test Specimen Manufacturing 3) Hierarchical macro-micro model development of three point bending and clinch test 4) Calibrate hierarchical macro-micro model to an AlSi7MgMn (Aural-5) HPDC Al alloys with multiple e-coating conditions 5) Validation of the model parameters using HPDC Aural-5 alloys with multiple casting conditions 4.1 Alloy selection and microstructure characterizations The high pressure diecast (HPDC) Al alloy (Aural-5: Al7SiMgMn) is selected for this work, with Si as the major alloy element with around 7 wt% concentration, Mg and Si as minor alloy elements with less than 1 wt% concentration. This alloy is highly castable and possess good combination of strength and ductility and is the prime focus at Ford Motor company for use in super-large HPDC of car front-end, back-end and underbody structures, providing potentials for significant weight and cost reduction for electric vehicles. In this study, the HPDC aural-5 plate with a thickness of 2.85 mm is used, both in as-cast (F temper) and e-coated condition (H81 temper). The microstructure characterization of the as-cast condition is mainly performed through the optical microscope

Read the complete text