Rolling-mill (1911 Encyclopaedia Britannica article)

Encyclopaedia Britannica · 1911

Read Rolling-mill (1911 Encyclopaedia Britannica article) by Encyclopaedia Britannica (1911) in the Tower of Babel, a free online library of public-domain works preserved in clean, searchable text. No sign-up. The full text is served as a plain-text file at a predictable URL, where text is present: https://antarctic-labs.com/tower-of-babel/britannica-1911-rolling-mill.txt.

Introduction

Rolling-mill is the subject of a trade article in the 1911 Encyclopaedia Britannica. The term covers several kinds of machines that make the shaped bars of wrought iron and steel. Boiler makers, platers, bridge builders, and builders in general need those shapes for their work. The entry sets the two metals side by side at the start.

The article says the making of wrought iron had shrunk for many years while the making of steel grew. The plant for both rests on the same basic plan, but steel changed the practice by the sheer size of its sections. Iron sections are small and often built up by piling small bits of worked metal. Steel sections, however large, are rolled from solid cast blocks. The work starts near a white heat and goes on until the metal cools to a low red.

Catalog record

CREATOREncyclopaedia Britannica
YEAR1911
COLLECTIONREFERENCE
FORMATTXT
FILE SIZE16 KB
VERSION1.0
LICENSEPublic Domain
RIGHTSPUBLIC DOMAIN
SOURCEWikisource — 1911 Encyclopaedia Britannica

Source: https://en.wikisource.org/wiki/1911_Encyclop%C3%A6dia_Britannica/Rolling-mill

Browse the full library · About the Tower of Babel

Full text

The opening of the work, from the library's hosted text:

ROLLING-MILL, a term which includes several types of machines used for producing the sectional forms (fig. 1) in which wrought iron and steel are required for the use of boiler-makers, platers and bridge-builders, and for constructional work generally. The production of wrought iron has been a diminishing industry for many years, while that of steel increases. Though the plant employed for both is alike in essential principles of design, the growth in the use of steel has revolutionized the practice, chiefly on account of the more massive dimensions in which steel sections are rolled. Iron sections are relatively small, and many are produced by piling, i.e. by building up with small portions of malleable puddled metal. There is no limit in reason to the dimensions in which steel sections can be rolled, and they are never piled, however large, but always rolled from solid cast ingots. When steel ingots are rolled into sectional forms the reduction in transverse dimensions is very great. The work begins at nearly a white heat, and continues until a low red is reached. Obviously the stresses to which the material is subjected are very severe. For this reason the process of reduction has to be effected very gradually, and especially so in those cases where reduction is being done in two directions at right angles with each other, as in channel sections (fig. 6) and joist or beam sections (figs. 7 and 8). It might be thought, since steel is always cast previously to rolling, that it might be cast at once into the sectional forms required. But sound results could not be obtained in this way, because the gases occluded in the metal form blow-holes which are sources of weakness. The material itself, even in the solid portions, is not homogeneous. By removing the head of the ingot where the blow-holes chiefly congregate and rolling the remainder at a white or red heat, the metal is improved by consolidation, and by the work done upon it. To this practice there is no exception. center|400px ac|Fig. 1.—Forms of the Principal Rolled Sections. 1, 2, Flats. 3, Flat with bevelled edges. 4, 5, Flats with rounded edges. 6, Bulb bar. 7, Wedge bar. 8, Scree or grate bar. 9, Square. 10, Triangular. 11, Hexagonal. 12, Round. 13, Oval. 14, Hollow half-round. 15, Half-round. 16, Convex. 17, Square-edged convex. 18, Vee. 19, O.G. 20, Angle iron. 21, Square root, or square throat angle. 22, Round-backed angle. 23, Unequal-sided angle. 24, Acute angle. 25, Obtuse angle. 26, Bulb angle. 27, Tee. 28, Bulb tee. 29, 30, Beams or joists, or girders, or H-irons. 31, Channel. 32, Zed. 33, Cruciform section. 34, Pillar section. 35, Troughing. 36, 37, 38, Railway rail. 39, Tramway rail. 40, Heavy crane rail. } Rolling-mills are known as “two-high,” or “three-high,” according as two or three rolls are mounted one over the other (figs. 2 and 3). In the two-high type the two rolls revolve in opposite directions, so that an ingot, slab or bloom presented to the entering side is drawn in and between the rolls, which reduce its thickness. In the case of rolls which are two perfectly plain cylinders (plate-rolls) the shape produced is that of broad, long and flat plates or sheets. Several passages (passes) are required to effect the reduction required, because this must be gradual. To regulate the amount the top roll is set down bodily by means of screws pressing on its bearings which slide in the end supports (housings). In the case of plate-rolls, which are plain cylinders, this setting down must be equal at each end. The mass of the top roll is balanced, to avoid shock when a plate is entering. The rolls are made of cast iron, and are either grain rolls or chilled rolls. The first are formed from a tough strong grade of iron, the quality which is used for all the roughing down and general work. The second are made of a highly mottled iron, cast against a cold mould (chill) of cast iron, by which a steely surface is obtained. These are used for fine finishing, or for imparting a polished surface to a section already nearly reduced to size in grain rolls. In later heavier practice, rolls of cast steel and forged steel are becoming common. They are more costly than iron, but more durable and much lighter for equal strength. They are essential in armour 'plate rolls. The length of rolls should not exceed about four times their diameter, for otherwise they are liable to spring and produce plates thicker at the centre than towards the edges. From this elementary design several types are derived. In the two-high mill it is clear that if the direction of the rotation of the rolls is always the same, then the plate being rolled must be taken back after each “pass” to the front of the rolls. Hence there is one “lost pass” for every reduction in thickness. This is the case in the “pull-over” mill, nearly obsolete. In the two-high reversing mill, introduced to avoid this “lost pass,” as soon as a plate has gone through, the direction of rotation of the rolls is reversed, and the plate is rolled again on the backward, journey, so avoiding the lost pass. An alternative is the three-high mill, in which three rolls are used. Here the plate is run through the lower rolls and back through the upper ones, so that there is no reversal of direction of the mill as a whole, but the lower and upper rolls draw the plates in opposite directions (see also Iron and Steel, § 129). center|810px Fig. 2.—General Arrangement of 12-in. Merchant and Guide-Mill Plant. (Thomas Perry & Son Ltd., Bilston.) pl6 pr6| A, First roughing rolls. B, Second ditto (C, Guide rolls for ovals or diamonds. D, Ditto for rounds or squares. E, Driving pinions. Engine, 30 in. × 22 in. cylinder, direct-coupled to rolls. Runs from 100 to 180 revolutions per minute to suit work. The shears are used for cutting the smaller sections the hot saw for cutting the merchant iron. } 60% center|810px Fig. 3.—12-in. Merchant Guide-Mill and Engine. Four-set mill. pl4 pr4| A, B, Three-high sets. C, Works either three-high or two-high; a, being a dummy roll. D, Two-high set (guide rolls). E, Coupling pieces. F, Housings. G, Pinions. The mill is capable of rolling rounds, squares, flats, angles, tees or similar sections by changing the rolls. The guide rolls D are used for small sections, and the second set B for merchant iron (larger sections). } Plate-Mills.—In Great Britain plate-mills are generally two-high reversing mills, in America three-high mills. Another difference is that in British practice two stands of rolls are used, in America one only. In the two-stand design there are two sets of rolls coupled endwise, one set being grain-rolls for roughing, and the other chilled rolls for finishing. Sets of live rollers conduct the plates to and from the separate rolls. The plate-mills proper are those which roll from 4 in. to about 2 in. thick. Armour plate-mills are a special design for massive plates and sheet-mills are for thin plates or sheets having a

Read the complete text