Real-Time State Estimation in Smart Grids over 5G Networks: Experimental Validation Using Raspberry Pis and Typhoon HIL
Biswajit Kumar Dash, Luis Herrera, Filippo Malandra · 2026
Read Real-Time State Estimation in Smart Grids over 5G Networks: Experimental Validation Using Raspberry Pis and Typhoon HIL by Biswajit Kumar Dash, Luis Herrera, Filippo Malandra (2026) in the Tower of Babel, a free online library of public-domain works preserved in clean, searchable text. No sign-up. The full text is served as a plain-text file at a predictable URL, where text is present: https://antarctic-labs.com/tower-of-babel/arxiv-2606-27642.txt.
Introduction
Smart grids need fast, reliable communication for live monitoring and control. Fifth-generation mobile networks promise low delay and high reliability. Most earlier studies of 5G for grids relied on simulation, though. Biswajit Kumar Dash, Luis Herrera, and Filippo Malandra instead validate with real hardware in 2026. Their testbed uses Raspberry Pi grid nodes and a Typhoon hardware-in-the-loop simulator.
The team first measured 5G performance under varied reporting rates and settings. Delay, jitter, and frame loss were the key measures. Worst-case mean delay came out about six and a half times lower than in their earlier LTE study. Real measurements then streamed from an IEEE four-node feeder model. Voltage, current, and phase angle went to a remote data concentrator. State estimation stayed accurate under steady and changing loads. Fault detection was reliable and prompt. The fastest detection delays were about eight tenths of a second.
Catalog record
| CREATOR | Biswajit Kumar Dash, Luis Herrera, Filippo Malandra |
|---|---|
| YEAR | 2026 |
| COLLECTION | PAPERS |
| FORMAT | TXT |
| FILE SIZE | 45 KB |
| LICENSE | http://creativecommons.org/licenses/by/4.0/ |
| RIGHTS | CC BY |
| SOURCE | arXiv |
Source: https://arxiv.org/abs/2606.27642
Browse the full library · About the Tower of Babel
Full text
The opening of the work, from the library's hosted text:
Real-Time State Estimation in Smart Grids over 5G Networks: Experimental Validation Using Raspberry Pis and Typhoon HIL Biswajit Kumar Dash, Luis Herrera, Filippo Malandra Abstract Reliable, low-latency communication is critical for real-time monitoring and control in modern Smart Grids (SGs). The emergence of 5G networks, with enhanced reliability, significantly lower latency, and native support for massive machine-type communication, offers strong potential to enable advanced grid applications such as state estimation (SE) and fault detection. While existing studies investigate 5G for SG use cases, most rely on simulations or analytical models; experimental validation using real hardware and SG data remains limited. This paper fills this gap by presenting a fully experimental validation of real-time SE over a commercial 5G network using a 5G-based multi-node testbed built with Raspberry Pi (RPi)-based SG nodes and a Typhoon Hardware-in-the-Loop (HIL) real-time simulator. We first characterize 5G communication performance using simulated SG data under varying reporting rates and deployment environments by evaluating Key Performance Indicators (KPIs) such as end-to-end delay, jitter, and frame loss. Experimental results show that the worst-case mean delay observed for the 5G is approximately 6.5 × \times lower than that of our previous LTE cat-M study at the corresponding reporting rate. We then stream real-time voltage, current, and phase-angle measurements—generated by an IEEE 4-node feeder model in Typhoon HIL simulator—to a remote Phasor Data Concentrator (PDC) for SE and fault detection. Results demonstrate that 5G-enabled measurements support accurate SE under both steady-state and dynamic load variations. Furthermore, fault-detection experiments confirm reliable and prompt fault detection, with detection delays as low as 0.80 s. I Introduction Emerging and future SG ( SG ) systems increasingly rely on advanced communication and networking technologies to meet the growing complexity and diversity of modern power systems. With global shifts towards sustainable energy sources and the adoption of diverse SG applications, there is a pressing need for enhanced reliability, reduced latency, and scalable connectivity. These improvements are crucial for enabling efficient, bidirectional data exchange across the distributed power grid, thereby supporting intelligent monitoring, estimation, and decision-making capabilities. The growing demand for reliable, high-performance, and scalable communication solutions in SG applications has driven the adoption of 5G technology, built upon its three foundational pillars: eMBB ( eMBB ), URLLC ( URLLC ), and mMTC ( mMTC ) [ 5 ] . These capabilities promise to meet the stringent requirements of SG functions such as real-time monitoring, distributed control, and SE ( SE ), which are critical for ensuring grid stability and resilience. Despite these promises, the practical deployment of 5G in SG environments requires rigorous performance analysis to validate its ability to deliver low latency, high reliability, and scalability under realistic conditions. Existing studies have primarily relied on three approaches: mathematical analysis (e.g., [ 28 ] ), which offers theoretical insights but often oversimplifies network behavior; network simulation [ 5 , 6 ] , which enables large-scale scenario modeling but lacks hardware-level fidelity; and field trials (e.g., [ 13 ] ), which provide real-world validation but are costly and difficult to scale. Moreover, these methods rarely capture the tight coupling between communication performance and power system dynamics, leaving a critical gap in understanding the end-to-end behavior of SG applications over 5G networks. To address this gap, experimental performance analysis has emerged as a promising alternative [ 23 , 9 , 7 ] . Unlike purely simulated environments, experimental setups allow direct measurement of latency, throughput, and reliability while accounting for hardware constraints, protocol overheads, and environmental factors. More importantly, by integrating communication hardware with real-time power system simulators such as Typhoon HIL ( HIL ) or OPAL-RT, researchers can evaluate how network performance affects essential grid functions, such as SE and control [ 17 ] . This holistic approach provides actionable insights for system operators and technology developers. However, experimental evaluation introduces its own challenges, including the complexity of integrating heterogeneous hardware, ensuring synchronization between communication and power domains, and maintaining reproducibility across different test conditions. In this work, we present a multi-node experimental testbed that leverages COTS ( COTS ) devices, such as RPi ( RPi ) units equipped with 5G connectivity, integrated with a Typhoon HIL real-time simulator. This architecture enables the execution of SE algorithms over a commercial U.S.-based 5G communication network while maintaining tight coupling with power system dynamics. By combining cost-effective hardware with high-fidelity simulation, our approach delivers a scalable and reproducible platform for evaluating 5G performance in SG applications. The results demonstrate the feasibility of deploying 5G for critical SG functions and provide valuable insights into latency, reliability, and integration challenges. The main contributions of this work are as follows: • Design and deployment of a multi-node testbed that integrates 5G connectivity with high-fidelity real-time power system simulation with Typhoon HIL . • Experimental evaluation of 5G network performance to study its feasibility for a variety of SG applications. • Validation of real-time SE over a commercial 5G network using synchrophasor data from an IEEE 4-node feeder. • Demonstration of fault-detection capability by injecting faults into the test feeder and showing that a global residual-based metric can reliably and quickly identify fault events. The remainder of this paper is organized as follows. Section II reviews the state of the art. Section III describes the architecture of our 5G-enabled SG testbed. Section IV presents experimental results on the 5G communication performance. Section V provides the real-time SE framework and experimental validation over 5G networks. Finally, Section VI concludes the paper. II State of the Art This section reviews the existing literature on communication technologies for SG in Section II-A , discusses how communication performance influences key SG applications in Section II-B , and identifies the research gaps that motivate this work. II-A Communication Technologies for Smart Grids Communication networks play a critical role in supporting monitoring, control, and automation in modern SG [ 24 , 25 ] . Although both wired and wireless technologies have been explored to meet the stringent latency, reliability, and scalability demands of emerging grid applications, wireless networks become attractive due to their flexibility, scalability, and lower installation cost [ 3 ] . A variety of wireless technologies, including WLANs and Zigbee, has been examined for distribution-level monitoring and control [ 11 , 16 ] . Although these systems demonstrate useful capabilities, their reliability, coexistence performance, and coverage limitations restrict large-scale deployment in SG environments. Zigbee, for instance, is particularly vulnerable in harsh or interference-heavy environments [ 8 ] . Broadband cellular networks such as 3G and LTE have also been evaluated for grid telemetry [ 19 ] , with studies considering both machine-to-machine (M2M) and mixed traffic scenarios [ 20 , 18 ] . However, LTE is not optimized for transmitting small, periodic sensor measurements due to its heavy protocol overhead [ 22 ] . Studies have therefore explored cellular IoT technologies such as LTE cat-M and NB-IoT, which offer reduced device costs, improved coverage, and lower energy consumption [ 14 , 10 ] . Our previous work experimentally evaluated LTE cat-M for SG communications using a single Arduino-based measurement node [ 23 ] and later extended the study to a multi-node configuration [ 9 ] . These studies highlighted two practical limitations. First, the measured delay