Individually tunable Si/SiGe quantum dot operating voltages via gate-biased illumination
Jared Benson, Sanghyeok Park, Owen M. Eskandari, M. A. Wolfe, Brighton X. Coe, J. P. Dodson, S. N. Coppersmith, Mark Friesen, M. A. Eriksson · 2026
Read Individually tunable Si/SiGe quantum dot operating voltages via gate-biased illumination by Jared Benson, Sanghyeok Park, Owen M. Eskandari, M. A. Wolfe, Brighton X. Coe, J. P. Dodson, S. N. Coppersmith, Mark Friesen, M. A. Eriksson (2026) in the Tower of Babel, a free online library of public-domain works preserved in clean, searchable text. No sign-up. The full text is served as a plain-text file at a predictable URL, where text is present: https://antarctic-labs.com/tower-of-babel/arxiv-2606-00446.txt.
Introduction
Benson and co-authors tune each gate of a silicon quantum dot rig with gate-held light. Such dot bits need far-split volts on each gate to sit right. That spread makes set-up slow and fiddly for each chip. Their trick moves trapped charge at the chip's face skin in a firm, set way.
Near heat-band light is shone while gate volts are held in place. The light shifts charge in a pat the team can steer and redo. Gate volts then fall in a much more matched range. A triple dot is tuned to small, matched volts as a show case. Wave-and-charge sims back the tale of how it works. Charge noise stays the same through the shift.
Catalog record
| CREATOR | Jared Benson, Sanghyeok Park, Owen M. Eskandari, M. A. Wolfe, Brighton X. Coe, J. P. Dodson, S. N. Coppersmith, Mark Friesen, M. A. Eriksson |
|---|---|
| YEAR | 2026 |
| COLLECTION | PAPERS |
| FORMAT | TXT |
| FILE SIZE | 38 KB |
| LICENSE | http://creativecommons.org/licenses/by/4.0/ |
| RIGHTS | CC BY |
| SOURCE | arXiv |
Source: https://arxiv.org/abs/2606.00446
Browse the full library · About the Tower of Babel
Full text
The opening of the work, from the library's hosted text:
Individually tunable Si/SiGe quantum dot operating voltages via gate-biased illumination Jared Benson, Sanghyeok Park, Owen M. Eskandari, M. A. Wolfe, Brighton X. Coe, J. P. Dodson, S. N. Coppersmith, Mark Friesen, M. A. Eriksson Abstract Semiconductor quantum dot qubits often require very different voltages on each gate to bring them to a correct operating point. Here, we present a method by which one can controllably and repeatably alter the nanoscale trapped charge distribution at an oxide-semiconductor interface. We demonstrate this method on a Si/SiGe quantum dot device, and we find that the operating voltages can be controlled and made much more uniform. The method relies on illumination with near-infrared light in the presence of applied gate voltages, and it enables the tuning of the device operating point on a gate-by-gate basis. We present an explanation of the underlying physics using self-consistent Schrödinger-Poisson simulations. As an application of this method, we tune a triple quantum dot to have uniform and small operating voltages in the (1,1,1) charge configuration. Importantly, we show that shifting the operating voltages in this way does not change the measured charge noise. Introduction Gate-defined semiconductor quantum dots offer a compelling candidate platform for quantum computing due to their small footprint and compatibility with conventional nanofabrication techniques [ 2 , 35 , 12 , 14 , 13 , 30 ] . However, typical device design parameters can lead to inconsistent and large operating voltages, in part due to charge traps at the interface between the semiconductor heterostructure and the gate oxide layer [ 22 , 17 ] . This can lead to difficult device tuning and incompatibility with instrumentation, particularly with cryo-CMOS electronics that tend to have severe power constraints [ 25 , 24 , 21 , 27 , 3 , 8 ] . These problems are relevant for scaling, where uniformity and cryogenic control are especially important [ 31 , 32 , 16 ] . While this can be mitigated through improved fabrication process control, this is a hard problem to overcome. Moreover, increasing the uniformity of the gates through better fabrication may not be a complete solution given that different types of gates, which are designed to fulfill different roles within the functioning of quantum dots, tend to be operated at substantially different voltages. An alternative approach to solve these issues is to improve the device characteristics in-situ after it is fabricated and cooled to cryogenic temperatures. Here, we present a technique to control the density of trapped charge underneath nanoscale gates in an oxide-semiconductor device, like those that define quantum dots, thereby enabling tunable control over the gate voltages required for device operation. The technique, which we call gate-biased illumination, is general and involves illuminating the device with above bandgap near-infrared light while simultaneously applying precisely chosen voltages to each gate. Compared to other methods that have been demonstrated to adjust the operating voltages of quantum devices, such as bias stressing [ 20 , 19 , 18 ] and bias cooling [ 10 , 6 ] , gate-biased illumination is fast, and it allows for more control over exactly where charge is rearranged in the device. We can measure the threshold for gate voltages above which charge is injected into the oxide layer, and we take care to avoid this limit [ 33 ] . We demonstrate that gate-biased illumination enables shifting the operating voltages on a gate-by-gate basis in a repeatable manner. As an application, we show how this technique enables placing the quantum dots in a low-gate-voltage operation regime and increases the uniformity of the required gate voltages. To explain the mechanism that makes it possible to tune the operating voltages, we simulate the process and the resulting pinch-off voltage shifts using Schrödinger-Poisson simulations. These shifts describe the effect of charge density modifications on the action of individual gates, including the largest shifts in the closest gates and smaller, but still non-negligible shifts in farther gates due to crosstalk. The simulated pinch-off voltage shifts show good agreement with experimentally measured results, suggesting that gate-biased illumination results in a controllable, highly non-uniform charge distribution at the oxide-semiconductor interface. Finally, we measure the charge noise, an important metric for qubit operation, following a gate-biased illumination used to translate the quantum dots into the low-voltage operation regime. We find that there is no significant difference in charge noise when comparing the low-voltage operating regime to the typical operating regime attained after the device is illuminated with 0 V applied to all its gates. Results and discussion Figure 1: Gate-biased illumination enables low-voltage operation of quantum dots. a A false-color SEM micrograph of a device that is nominally identical to the one measured here. b - d Cross-sections of the gate stack and upper layers of the Si/Si 0.7 Ge 0.3 heterostructure along the white dashed line in (a) showing the gate-biased illumination process. b Large and non-uniform gate voltages are required to form a triple quantum dot due to fixed oxide charges and interface trapped charges (not shown). c The device is illuminated with a 780 nm laser while its gates are biased with dc voltages. Photo-generated electron-hole pairs (white-black ovals) move to screen the electric fields in the quantum well and are localized in traps. d After the gate-biased illumination, the newly trapped charges are frozen in place at the semiconductor-oxide interface, allowing the quantum dots to operate at smaller, more uniform gate voltages. e A stability diagram showing operation of a triple quantum dot in the (1,1,1) configuration at low gate voltages following the gate-biased illumination detailed in Table 1 . The measurements reported here are performed using a Si/SiGe triple quantum dot. Figure 1 a is a false-colored scanning electron microscope (SEM) image of an overlapping-gate-defined semiconductor quantum dot device [ 34 ] with the same gate layout as the one measured here. Three layers of aluminum gates are patterned on top of a Si/Si 0.7 Ge 0.3 heterostructure with a Al 2 O 3 gate oxide layer [ 7 ] . The device is designed such that up to three quantum dots can be accumulated under plunger gates P1-P3, which are then measured by a charge sensor under the plunger gate P4. We adjust the operating voltages of the gates that define the quantum dots using a procedure we call gate-biased illumination, as illustrated in Fig. 1 b-d. This is a generalization to multi-gate devices of the technique illustrated on Hall bars in Ref. [ 33 ] . Figure 1 b is a cross-sectional diagram of the gate stack and the top layers of the heterostructure, taken along the white dashed line in Fig. 1 a. Here, the gates are shaded to depict the voltages that are applied when operating a triple quantum dot under the plunger gates P1-P3, which are enumerated in Table 1 a. These voltages are large and non-uniform due to charge traps at the oxide-semiconductor interface and fixed charges in the oxide layer (not shown), of which many are intrinsic and some arise from imperfect fabrication. Additionally, gates usually must be set to different voltages depending on what purpose they serve. For instance, barrier gates are typically set to lower voltages than plunger gates to properly define quantum