Significant heat transfer enhancement via polymer additives in two-dimensional sheared convection
Guanhan Li \aff 1 \corresp, Lu Zhu \aff 1 \corresp & Rich. R. Kerswell \aff 1 · 2026
Read Significant heat transfer enhancement via polymer additives in two-dimensional sheared convection by Guanhan Li \aff 1 \corresp, Lu Zhu \aff 1 \corresp & Rich. R. Kerswell \aff 1 (2026) in the Tower of Babel, a free online library of public-domain works preserved in clean, searchable text. No sign-up. The full text is served as a plain-text file at a predictable URL, where text is present: https://antarctic-labs.com/tower-of-babel/arxiv-2605-06657.txt.
Introduction
Guanhan Li, Lu Zhu, and Rich R. Kerswell show that adding polymers to a fluid can boost heat transfer enormously in sheared convection. Better cooling matters across engineering, and elastic additives are a candidate route. They study a two-dimensional, thermally stratified Poiseuille flow at moderate Reynolds numbers, where two unstable modes compete: an elasticity-driven centre mode and a classical buoyancy-driven convective mode.
Simulations show the centre mode barely improves heat transfer. The convective mode is different: polymer stress forms hook-like structures that can raise heat flux by up to eleven times over. Wall-attached hooks create strong rolls and extreme gains but a large flow penalty, while free hooks offer a more efficient regime.
Catalog record
| CREATOR | Guanhan Li \aff 1 \corresp, Lu Zhu \aff 1 \corresp & Rich. R. Kerswell \aff 1 |
|---|---|
| YEAR | 2026 |
| COLLECTION | PAPERS |
| FORMAT | TXT |
| FILE SIZE | 61 KB |
| LICENSE | http://creativecommons.org/licenses/by/4.0/ |
| RIGHTS | CC BY |
| SOURCE | arXiv |
Source: https://arxiv.org/abs/2605.06657
Browse the full library · About the Tower of Babel
Full text
The opening of the work, from the library's hosted text:
Significant heat transfer enhancement via polymer additives in two-dimensional sheared convection Guanhan Li \aff 1 \corresp, Lu Zhu \aff 1 \corresp & Rich. R. Kerswell \aff 1 Abstract Heat dissipation is critical in modern engineering systems. Polymer additives offer a potential route to improve fluid-based cooling. Here, we study elasticity-enhanced heat transfer in two-dimensional, thermally-stratified Poiseuille flow. At Reynolds numbers, R e Re , ≲ 1000 \lesssim 1000 , we observe two types of linearly unstable modes: the recently identified elasticity-induced centre mode (Khalid et al. , J. Fluid Mech. 915 , 2021) and the classical buoyancy-driven convective mode (Kelly, Adv. Appl. Mech. 31 , 35–112, 1994). Direct numerical simulations show that the centre mode develops into a nonlinear ‘arrowhead’ state but yields negligible heat transfer enhancement (typically ≈ 0.03 % \approx 0.03\% increase compared to the conductive state). By contrast, polymers can enhance the heat flux associated with the convective mode by up to 1100 % 1100\% . The nonlinear convective-mode states take the form of either periodic orbits or travelling waves, and are dominated by hook-like polymer-stress structures that can attach to the walls. The unattached hooks act as ‘speed bumps’ that reduced streamwise velocity and promote wall-normal motion, whereas wall-attached hooks form effective ‘polymer walls’, reorganising the flow into strong counter-rotating rolls and triggering the extreme-enhancement regime. The elasto-buoyant nature of these states is confirmed by perturbation kinetic energy budgets, which show that polymer and buoyancy sustain the states synergistically. The wall-attached hooks enable rapid thermal equilibration but impose a large hydraulic penalty, making them suitable for process streams requiring fast temperature adjustment. Unattached hooks provide a more thermally efficient regime for heat-transport applications. These results highlight the potential of elastic fluids for future heat transfer enhancement technologies. \lefttitle Li et al. \righttitle Heat transfer enhancement in polymer solutions keywords shear-flow instability, stratified flows, viscoelasticity 1 Introduction Modern electrical devices often demand efficient cooling systems to dissipate heat and maintain optimal operating conditions ( 50 ) . For example, driven by significant progresses in lithography and advanced packaging, the typical heat generated by modern high-performance electronics requires cooling heat fluxes exceeding 10^{3}\ \mathrm{W/cm^{2}} ( 41 ) . The present primary cooling system remains air-based, but the next generation focuses on the fluid-flow based system, underscoring the importance of hydrodynamics in contemporary thermal management ( 20 ; 41 ) . In many practical cooling configurations, a working fluid passes through a channel where one wall is heated and the opposite wall is much cooler, producing a thermally stratified layer. A canonical framework that captures this interplay of forced and buoyancy-driven motions is the Rayleigh–Bénard–Poiseuille (RBP) flow, in which a pressure-driven stream in a horizontal channel is subjected to a transverse temperature gradient. Instabilities in this configuration manifest through two primary pathways: shear mechanisms dependent on the Reynolds number Re that provoke Tollmien–Schlichting waves ( 31 ) , and buoyancy-driven modes governed by the Rayleigh number Ra or the Richardson number Ri that result in the formation of convective rolls ( 16 ; 27 ) . However, in many practical applications, such as microchannels in solar units or electronic cooling chips ( 32 ; 18 ) , Re typically remains of the order \mathcal{O}(10^{2}) , a regime where only buoyancy instability is triggered. Consequently, leveraging buoyancy instability to optimise thermal performance has become an active area of research. 35 experimentally demonstrated that buoyancy-induced secondary flows significantly enhance heat transfer compared to pure forced convection. Expanding on this work, 36 combined experiments with simulations to provide a detailed map of flow pattern evolution throughout the entire channel: from the entrance to the later turbulent regions. Furthermore, 48 employed 3D numerical simulations to investigate how Rayleigh number Ra , Reynolds number Re and lateral confinement affects the stability limits and transitions between longitudinal and transverse roll structures in mixed convection. Beyond passive mechanisms, active control strategies to further increase heat transfer in RBP flows ( 44 ; 43 ) have also been investigated. One potential strategy to overcome this limitation is the addition of long-chain polymers to the working fluid. The stretching and relaxation of these polymer chains give rise to elastic stresses, which can fundamentally modify flow stability ( 33 ; 8 ) . In channels featuring curved geometries, such as wavy or serpentine paths or those containing internal obstacles, the well-known hoop stress polymer instability can lead to elastic turbulence ( 12 ) . To date, the literature on elastic-induced heat-transfer enhancement (HTE) has largely focused on this phenomenon. For instance, 1 experimentally observed that heat transfer increased by up to 200% for low polymer concentrations and up to 380% for higher concentrations compared to equivalent Newtonian flows in a serpentine channel. Similarly, 30 numerically demonstrated that heat transfer can reach approximately twice that of its Newtonian counterpart in channels with obstacles. Other experimental ( 38 ; 40 ; 45 ) and numerical ( 22 ; 11 ) studies have confirmed this HTE phenomenon induced by elastic turbulence. Conversely, in straight-channel flows, some studies have reported a reduction in heat transfer in Rayleigh-Bénard convection ( 5 ; 42 ) , whereas others have observed both enhancement and suppression, with the reported enhancement remaining modest (e.g. about 2% in 39 and about 10% in 9 ). Recently, it has been found that other viscoelastic instabilities, such as the centre mode ( 17 ) and polymer diffusive instability (PDI) ( 3 ) can be triggered in a straight channel. However, the effectiveness of the resulting motions for heat flux has yet to be explored. This study represents a first attempt to address this issue, specifically focusing on cases where the centre mode is excited. In this paper, we will conduct linear stability analysis and direct numerical simulations to investigate HTE in viscoelastic, unstably-stratified (RBP flow) and stably-stratified shear flow. To the best of our knowledge, previous studies have only focused on the stability analysis of similar systems, and the HTE effect has not been previously investigated in the literature as this requires a finite-amplitude manifestation of the instability to assess. An early investigation of viscoelastic RBP flow ( 13 ) focused on the convective and absolute instabilities by linear stability analysis, finding that while fluid elasticity acts to stabilise transverse rolls in the presence of throughflow, it significantly accelerates the transition to absolute instability. 47 also conducted linear stability analysis and identified three distinct instability regimes governed by shear intensity (quantified by Re ), revealing a non-monotonic dependence where viscoelasticity acts to destabilise the flow at low and high Re but plays a stabilising role at moderate Re . In contrast to these modal analyses, 46 focused on the linear non-modal dynamics of similar systems and uncovered a substantial transient energy growth driven by the coupling between polymeric stresses and temperature gradients. Furthermore, 15 considered the effect of viscous heating, highlighting that the buoyancy induced by internal viscous dissipation can dramatically exacerbate purely elastic instabilities by lowering the critical Weissenberg number W . The rest of this paper is organised as follows. § 2 formulates the physical problem and its governing equations. § 3 is dedicated to linear stability analysis and a discussion of the fastest-growing modes. In § 4