Real-Time Wiener Deconvolution for feature reconstruction in JUNO

X. Yan · 2026

Read Real-Time Wiener Deconvolution for feature reconstruction in JUNO by X. Yan (2026) in the Tower of Babel, a free online library of public-domain works preserved in clean, searchable text. No sign-up. The full text is served as a plain-text file at a predictable URL, where text is present: https://antarctic-labs.com/tower-of-babel/arxiv-2603-25436.txt.

Introduction

Lastrucci and co-authors sharpen neutrino signals in real time on the JUNO detector's own electronics. JUNO's light sensors produce floods of data, and faint events drown in background noise. Their Wiener deconvolution runs on FPGA boards inside the readout chain. It rebuilds each sensor pulse as it arrives, with tiny delay and high throughput. Cleaner low-energy events can then be kept instead of dropped for storage reasons. That matters for brief cosmic flashes. Board tests show the design holds up at full stream rates.

Catalog record

CREATORX. Yan
YEAR2026
COLLECTIONPAPERS
FORMATTXT
FILE SIZE44016
LICENSEhttp://creativecommons.org/licenses/by/4.0/
RIGHTSCC BY
SOURCEarXiv

Source: https://arxiv.org/abs/2603.25436

Browse the full library · About the Tower of Babel

Full text

The opening of the work, from the library's hosted text:

Real-Time Wiener Deconvolution for feature reconstruction in JUNO X. Yan Abstract In particle physics, experiments generate substantial amounts of data that can be difficult to process without preliminary scaling. To avoid losing potentially crucial data, experimental collaborations are studying novel techniques for real-time data processing to extract features for further physics analysis. A common approach, especially in neutrino physics, is to use FPGAs for data acquisition and pre-processing. This paper presents an advanced Real-Time Wiener deconvolution algorithm designed to leverage the processing capabilities of the FPGA integrated into the readout boards of the Jiangmen Underground Neutrino Observatory (JUNO). The goal is to enable real-time reconstruction of the signal generated by photomultiplier tubes (PMTs) when neutrino interactions are detected. By exploiting online reconstruction of the signal generated by PMTs, we expect to improve the detection of low-energy depositions, such as those produced by transient astrophysical phenomena. These depositions are usually not saved because of the significant background that affects the low end of the energy spectrum, which would result in a large trigger rate, hence a large amount of data required for storage. This paper presents the features of the algorithm, including its ability to manage high-throughput data streams with minimal latency, adaptability, and resilience in discerning the characteristics of input data. Performance is evaluated on a JUNO electronic board. This study further demonstrates the potential of FPGA-based solutions for neutrino physics. 1 Introduction In experimental particle physics, there is a growing trend toward collecting and analyzing large volumes of data. This is particularly relevant at the intensity frontier, where large detector volumes are often required to compensate for low cross-sections and low fluxes. Neutrino experiments based on technology are a prime example, where large detection volumes correspond to a high count of readout channels. To handle these signals while preserving the features of the output, recent and future experiments [ 5 , 11 , 1 , 3 ] implement analog-to-digital conversion near the . The transmission of digital data to the farm requires low-level processing, usually achieved using a . offer significant computational capabilities, re-programmability, and operational consistency, all while maintaining relatively low costs. Beyond handling I/O, resources can perform signal pre-processing and filtering. This enables the extraction of relevant features from the output signal (hereafter referred to as the waveform ), avoiding the need to transmit the entire sampled waveform—a task that can be extremely demanding given high sampling frequencies and large channel counts. This approach is crucial when an experiment searches for multiple signatures that differ in rate and energy-resolution requirements. Events requiring high energy resolution benefit from high-frequency digitization to properly disentangle all photons hitting the . However, the acquisition rate for such events is limited by the bandwidth between the readout electronics and the . To retain high-rate signatures, such as low energy events highly contaminated by natural radioactivity background, online pre-processing must occur on the readout electronics board, ensuring that only the most relevant waveform features are transmitted. In this article, we present a novel approach to waveform feature reconstruction called , a real-time reconstruction technique for waveform processing based on the Deconvolution algorithm. It aims to disentangle contributions —which we call hits — within a given waveform to improve the reconstruction of hit times and total charge. This work was initiated in the context of the experiment; therefore, we describe the detector and the method’s application to it. However, the algorithm’s performance and the results of the study are pertinent to any -based detector featuring an on its readout electronics. The paper is organized as follows: section 2 introduces the experiment, section 3 describes the experimental setup used to develop and test the algorithm, section 4 introduces the algorithm, while section 5 details the use case. In section 6 we presente the results of the tests conducted. Finally, we draw our conclusions in section 7 . 2 Jiangmen Underground Neutrino Observatory The [ 5 ] is a 20 kton multipurpose underground liquid scintillator detector designed to study neutrino interactions by detecting scintillation and Cherenkov light. It employs a dual photodetection system consisting of 17,612 20-inch and 25,600 3-inch . The operate within a wide dynamic range, spanning from a single photoelectron to several hundred within a 1~\mu s readout window. Each group of three connects to a readout board known as a , which comprises six units and an AMD Kintex 7 . As the use a different readout strategy, they are excluded from this study; consequently, the term will hereafter be used exclusively to refer to the . Each connects to two amplifiers with distinct gains, producing two output signals per . Each signal is sampled at 1 GS/s and digitized with a resolution of 14 bits using a dedicated . Every waveform sample is stored as two 8-bit words. The digital output is parallelized into eight data streams at 125 MHz via a to align with the clock. Consequently, for a given , the processes eight waveform samples per clock cycle—each sample being 16 bits wide—resulting in a total bus width of 128 bits. The primary tasks of the are: (i) to receive digitized data from the , to pack them, and to transmit them to the ; and (ii) to generate trigger primitives when waveforms exceed a defined threshold. These primitives are subsequently evaluated by the Back-End electronics to issue a global trigger, which initiates the readout of all active channels. A more comprehensive description of operations and JUNO electronics is provided in ref. [ 14 ] . Since is responsible for waveform acquisition, trigger generation, and basic data processing, a large fraction of its resources have already been allocated. The goal of this study is to improve trigger efficiency, hit identification, and total charge reconstruction using the limited resources that remain available. The baseline operation of the electronics yields two distinct data streams: (i) , representing a stream of fully digitized signals segmented into readout windows—each window comprising 1008 samples—and recorded only upon event validation by the ; and (ii) , a trigger-less stream of Time and Charge pairs for each hit, which are continuously reconstructed and saved. The readout system stores the full WF only when the issues a global trigger , which means that the number of trigger primitives, namely PMTs firing, is above a predefined threshold. Storing all —each worth 2 kB—for all events would be infeasible, because the trigger rate induced by cosmic muons is roughly 4 Hz, and storing roughly 17,000 per event yields 33.2 MB/event, i.e., approximately 11 TB per day. In contrast, serve as a compression of . Whenever a is detected, its charge and timestamp are calculated (currently through the algorithm, described later in this section) and sent directly to the . This allows continuous recording of single activity—even in the absence of a globally validated event—without exceeding bandwidth limits. The method defines a hit whenever the amplitude of the waveform exceeds a threshold and computes its charge as the integral of all samples exceeding the said threshold. Each hit yields a pair, where the timestamp is defined as the time the threshold was exceeded. The algorithm is able to disentangle two photoelectrons close in time only if the waveform goes back

Read the complete text