The Role of Dynamic Stall in Aerofoil Shape Optimisation for Curvilinear Blade Kinematics

Swathi Krishna · 2026

Read The Role of Dynamic Stall in Aerofoil Shape Optimisation for Curvilinear Blade Kinematics by Swathi Krishna (2026) in the Tower of Babel, a free online library of public-domain works preserved in clean, searchable text. No sign-up. The full text is served as a plain-text file at a predictable URL, where text is present: https://antarctic-labs.com/tower-of-babel/arxiv-2603-08277.txt.

Introduction

Irwin and colleagues study how dynamic stall shapes aerofoil optimisation for curvilinear blade kinematics. The study uses a cyclorotor in hover, typical of vertical-axis turbines and cycloidal props, as its test case. Two-dimensional unsteady RANS simulations coupled with Kriging shape the design, which is then tested with force measurements and PIV. Results improve through suppression of leading-edge vortex shedding during the primary thrust peak.

Catalog record

CREATORSwathi Krishna
YEAR2026
COLLECTIONPAPERS
FORMATTXT
FILE SIZE38496
LICENSEhttp://creativecommons.org/licenses/by/4.0/
RIGHTSCC BY
SOURCEarXiv

Source: https://arxiv.org/abs/2603.08277

Browse the full library · About the Tower of Babel

Full text

The opening of the work, from the library's hosted text:

The Role of Dynamic Stall in Aerofoil Shape Optimisation for Curvilinear Blade Kinematics Swathi Krishna Abstract This study investigates the influence of aerofoil shape optimisation on blade aerodynamic performance under curvilinear and unsteady kinematics characteristic of vertical-axis turbines and cycloidal propellers. Using a cyclorotor in hover as a representative configuration, aerofoil optimisation was performed using two-dimensional unsteady Reynolds-averaged Navier–Stokes simulations coupled with Kriging. The optimised design was subsequently validated experimentally through force measurements and flow-field characterisation using particle image velocimetry. Performance was enhanced through the suppression of leading-edge vortex separation during the primary thrust peak. This finding also reveals a governing constraint: the effectiveness of aerofoil optimisation depends on dynamic stall severity. Under light dynamic stall, geometric modification promotes vortex attachment and improves aerodynamic loading. Under deep dynamic stall, flow separation dominates the blade aerodynamics, and aerofoil shape modification cannot suppress leading-edge vortex shedding. The stall severity is regulated by rotor solidity through its influence on the induced throughflow-to-blade-speed ratio and the resulting effective incidence. Aerofoil optimisation is therefore viable primarily in high-solidity configurations that operate within a moderated stall regime. These findings establish a physics-based condition for aerofoil optimisation in curvilinear dynamic stall environments. 1. Introduction Recent years have seen the emergence of vertical axis turbines (VATs) and cycloidal propellers (cyclorotors), devices that share common aerodynamic principles yet serve distinct applications in renewable energy and propulsion. Both configurations comprise a rotating cylindrical arrangement of blades. VATs can offer improved performance in high-density wind farms and operate effectively in highly variable wind conditions, despite often being less efficient than conventional horizontal-axis designs in standalone operation ( 11 ) . Cyclorotors are employed widely in Voith-Schneider propellers mounted on large ships ( 31 ) . These propellers leverage the thrust-vectoring capabilities of cyclorotors to enhance manoeuvrability, particularly during docking. While the use of cyclorotors in the maritime industry is not new, renewed interest for micro-air vehicles (MAVs) applications has emerged. At typical Reynolds numbers of 10,000-40,000, cyclorotors have demonstrated lower susceptibility than conventional rotors to the detrimental low-speed effects ( 27 ) . The rotating, cylindrical arrangement subjects the blades to a curvilinear flowfield characterised by curved streamlines and introduces associated aerodynamic phenomena. A principle feature of the flowfield around a blade in curvilinear flow is the chordwise variation in local-angle-of-attack. This variation results in a phenomenon known as virtual camber, wherein the blade’s aerodynamic behaviour can be approximated by that of a cambered aerofoil in rectilinear flow that maintains the same localised chordwise incidence ( 20 ) . For this effectively cambered shape, the zero-lift angle-of-attack ( \alpha_{0} ) can be determined and subsequently used to offset the geometric blade pitch ( \alpha_{geom} ), yielding an effective angle-of-attack ( \alpha_{eff} ) (Eq. 1 ). \alpha_{eff}=\alpha_{geom}-(\alpha_{0})_{\text{virtual camber}} (1) In addition to curvilinear effects, the rotating cylindrical arrangement of blades imposes highly unsteady flow conditions. This unsteadiness frequently induces the aerodynamic phenomena known as dynamic stall, wherein unsteady blade kinematics enable transient lift generation well beyond its static stall angle ( 21 ) . Dynamic stall is often accompanied by the formation of leading-edge vortices (LEVs), which arise as the boundary layer separates from the blade’s leading edge and rolls up into a large vortex close to the blade surface. Consequently, the resulting flowfields are heavily vortex-dominated. Cyclorotors present a compelling case for aerofoil optimisation, due to an inherent design trade-off linked to rotor solidity ( \sigma ), which represents the proportion of the rotor’s circumference that is occupied by blades. Rotor solidity is calculated using blade-count ( N_{b} ), blade chord ( c ) and rotor radius ( R ) (Eq. 2 ). For a fixed blade pitch amplitude and RPM, there will generally be some minimum level of solidity required to reach a target level of thrust. The means by which this solidity is realised introduces competing aerodynamic consequences (Fig. 1 ). Configurations employing high blade counts with shorter chord lengths produce a consistent thrust output, but typically suffer from reduced efficiency. Figure 1 : Two rotors of fixed solidity ( \sigma=0.3395 ) with (left) two blades with chord c and (right) four blades with chord c/2 \sigma=\frac{N_{b}c}{2\pi R} (2) This reduction in efficiency has been observed in both cyclorotors and VATs and is generally attributed to blade-to-blade interaction effects, arising from reduced inter-blade spacing, which promotes wake interaction between successive blades. ( 4 ; 39 ) . Cyclorotors additionally will often operate at high blade-pitch amplitudes to exploit the increased lift coefficient possible under dynamic stall. This operating mode promotes frequent LEV shedding and blade-vortex interactions. Given the strong dependence between aerofoil shape and flow separation, there is significant potential for aerofoil optimisation to improve the performance of high blade-count cyclorotors, thereby fully leveraging their inherent steady thrust characteristics. The concept of using cambered aerofoils in cyclorotors and optimising their shape has been explored in previous studies and have shown that the performance of a chosen cyclorotor configuration could indeed be improved through an optimisation of the aerofoil shape ( 28 ; 38 ) . The range of different aerofoil shapes used in these studies remain relatively restrictive and do not encompass geometries with leading-edge droops, which have been associated with additional performance benefits ( 9 ) . Overall, devices that utilise blades operating in curvilinear flow are subject to multiple complex and overlapping effects. Classical aerodynamic theory typically relies on the assumption of rectilinear 2D flows, which constrains the accurate interpretation and modelling of the blade aerodynamics in these environments. Such frameworks do not account for the coupled effects of virtual camber, dynamic stall, and blade–wake interaction inherent to curvilinear flows. Consequently, the aerofoil geometry-driven control of LEV behaviour, and the effectiveness of optimisation across different solidity remain unresolved, resulting in the absence of a clear set of physics-based design principles for achieving an optimum aerofoil shape. The aim of the current study is to investigate the governing physical mechanisms influencing aerofoil optimisation in a curvilinear flow. The study approaches this problem by optimising the aerofoil for a cyclorotor in the hover condition. The hover condition preserves the predominantly curvilinear inflow characteristics without the interference of the freestream effects, aligning with the primary focus of the investigation. Furthermore, in both maritime and aviation contexts, cyclorotors are frequently utilised in pure hover or at very low freestream speeds. To further examine the influence of rotor configuration on the resulting design principles, aerofoil optimisation is conducted for cyclorotors with 1-4 blades. This process will have the additional benefit of potentially highlighting how high blade-count cyclorotors can be made more viable to exploit their inherently steadier thrust output. Although cyclorotors represent a specific manifestation of curvilinear blade motion, the optimisation outcomes are expected to retain relevance for other devices such as VATs. Despite serving distinct functional roles, both configurations experience comparable governing aerodynamic phenomena, including virtual camber, wake intersection, and dynamic stall. Consequently, while the exact optimal geometries may differ between applications, the underlying design principles are expected to remain broadly consistent. 2. Methodology 2.1. Cyclorotor configuration and parametrization A 4-bladed cyclorotor operating at a representative Reynolds number of 30,000 was chosen as the primary baseline configuration for aerofoil optimisation (see Table 1 for details). In addition to the 4-blade configuration,

Read the complete text