6-mJ, 4-ns Pulse Generation at 2.09 µm from a Diode-Pumped Ho:YAG Thin-Disk Laser Journal: opticajournal Publication type: Research Article

Yuya Koshiba, 1,* Jiří Mužík, 1 Martin Smrž, 1 Matyáš Dvořák, 2, Sabina Kudělková, 3 Antonín Fajstavr, 3 and Tomáš Mocek 1 · 2026

Read 6-mJ, 4-ns Pulse Generation at 2.09 µm from a Diode-Pumped Ho:YAG Thin-Disk Laser Journal: opticajournal Publication type: Research Article by Yuya Koshiba, 1,* Jiří Mužík, 1 Martin Smrž, 1 Matyáš Dvořák, 2, Sabina Kudělková, 3 Antonín Fajstavr, 3 and Tomáš Mocek 1 (2026) in the Tower of Babel, a free online library of public-domain works preserved in clean, searchable text. No sign-up. The full text is served as a plain-text file at a predictable URL, where text is present: https://antarctic-labs.com/tower-of-babel/arxiv-2601-19760.txt.

Introduction

Yuya Koshiba and colleagues report a laser that fires short, strong pulses in the infrared. The device uses a thin disk of holmium-doped YAG crystal, pumped by laser diodes. It was run in two modes: Q-switching and cavity dumping, two standard ways to store and release light in bursts. The output wavelength sits near two micrometres.

The pulses carry more than six millijoules of energy and last only a few nanoseconds. That combination gives a peak power above a megawatt. The beam quality is near the diffraction limit, meaning it stays tight and clean. Such sources serve in materials processing, sensing, and further laser stages. The work shows what thin-disk designs can reach in this wavelength range.

Catalog record

CREATORYuya Koshiba, 1,* Jiří Mužík, 1 Martin Smrž, 1 Matyáš Dvořák, 2, Sabina Kudělková, 3 Antonín Fajstavr, 3 and Tomáš Mocek 1
YEAR2026
COLLECTIONPAPERS
FORMATTXT
FILE SIZE11 KB
VERSION1.0
LICENSEhttp://creativecommons.org/licenses/by/4.0/
RIGHTSCC BY
SOURCEarXiv

Source: https://arxiv.org/abs/2601-19760

Browse the full library · About the Tower of Babel

Full text

The opening of the work, from the library's hosted text:

6-mJ, 4-ns Pulse Generation at 2.09 µm from a Diode-Pumped Ho:YAG Thin-Disk Laser Journal: opticajournal Publication type: Research Article Yuya Koshiba, 1,* Jiří Mužík, 1 Martin Smrž, 1 Matyáš Dvořák, 2, Sabina Kudělková, 3 Antonín Fajstavr, 3 and Tomáš Mocek 1 Abstract A holmium-doped yttrium aluminum garnet (Ho:YAG) thin-disk was experimentally investigated under Q-switching and cavity-dumping operation schemes, pumped by a 1.9 µm laser-diode (LD). The laser generated pulses at 2090 nm with energies more than 6 mJ and pulse duration down to 3.8 ns, corresponding to a peak power of 1.6 MW with near-diffraction-limited beam quality. The compact and robust system was used for laser-induced breakdown spectroscopy (LIBS) experiments, demonstrating its practical usability. These results represent, to the best of our knowledge, the first demonstration of a Ho:YAG thin-disk laser providing MW peak-power in nanosecond regime. 1 Introduction Thin-disk lasers have become the workhorses of high-power and high-energy laser systems, alongside slab and fiber lasers [ 1 , 2 , 3 ] . Their advantageous geometry, which enables efficient heat dissipation, allows power scaling to kilowatt level without compromising beam quality. Yb-doped materials, typically Yb:YAG, operating near 1 µm have been successfully implemented in thin-disk architectures and have demonstrated tremendous progress over the past decades [ 4 ] . In addition, recent advances in nonlinear pulse compression using multi-pass cells have made it possible to achieve ultrashort, femtosecond pulses [ 5 , 6 ] . This trend may eventually replace Ti:sapphire lasers, which have long been the standard for ultrashort pulse generation. Consequently, Yb thin-disk lasers are commonly used as drivers for wavelength extension via nonlinear wavelength conversion techniques, such as harmonic generation for shorter wavelengths [ 7 , 8 ] and optical parametric oscillation/amplification (OPO/OPA) for longer wavelengths [ 9 ] . However, these methods suffer from limited conversion efficiency and require meticulous alignment. As Yb thin-disk lasers approach their performance limits, extending the thin-disk concept to other gain media that can directly generate other wavelengths has attracted growing interest [ 10 ] . In particular, the short-wave infrared (SWIR) region around 2 µm is of great interest due to its unique applications in spectroscopy [ 11 ] , remote sensing [ 12 ] , and material processing [ 13 ] . Scientific applications include driver sources for OPA [ 14 ] , high-harmonic generation [ 15 ] , laser-Compton scattering [ 16 , 17 ] , and extreme-ultraviolet generation via laser-produced plasma [ 18 ] . Among various candidate materials [ 19 , 20 ] , we have recently initiated studies on Ho:YAG thin-disk lasers. Here, we report our experimental results on a pulsed Ho:YAG thin-disk laser operated under Q-switching and cavity-dumping schemes. 2 Materials and Methods A Ho:YAG thin-disk crystal with doping concentration of 1.5 at.% and thickness of 400 µm was used. The doping level is higher than that generally used in rod lasers [ 21 ] to compensate for the low gain inherent to the thin-disk geometry. However, higher doping also leads to undesirable effects such as increased heat generation, energy-transfer upconversion (ETU), and excited-state absorption (ESA) [ 22 , 23 ] . Regarding the thickness, thinner crystal would improve the heat dissipation but reduce both the gain and the pump absorption. Sufficient pump absorption is important, as residual pump light may be reflected back to the pump source. To ensure safe operation and higher gain, we selected a comparatively thick crystal in this study. The heatsink was made of silicon carbide (SiC) which has three times lower thermal conductivity than chemical vapor deposited (CVD) diamond, but offers cost-effective alternative [ 24 ] . The Ho:YAG thin-disk was mounted in a 72-pass pumping head. The pump source was a commercial LD manufactured by QPC Lasers Inc., delivering up to 50 W of continuous-wave power at around 1.91 µm, corresponding to in-band pumping. However, it was not wavelength-stabilized with a volume Bragg grating (VBG) resulting in a broadband emission (12 nm full width at half maximum (FWHM)), and a temperature-dependent center wavelength. For Q-switching and cavity-dumping operations, a pair of rubidium titanyle phosphate (RTP) crystals with dimensions of 6×6×10 mm 3 was used as a Pockels cell (PC), driven by a high voltage (HV) driver with risetime below 5 ns. The experimental setup is depicted in Figure 1 . It is a simple setup with one arm containing a polarizer and an optical switch. Figure 1: Schematic of the experimental setup for (a) Q-switching and (b) cavity-dumping operations. OC: output coupler; QWP: quarter waveplate; RTP: rubidium titanyle phosphate; PC: Pockels cell; TFP: thin film polarizer; HR: high-reflective; CC: concave. In Q-switching, the pump energy is first stored in the gain medium. Ho:YAG possesses a long upper-state lifetime of about 7 ms [ 25 ] , which is advantageous for Q-switching. When a HV is applied to the PC, the resonator becomes low-loss (i.e., high-Q), allowing laser buildup and pulse emission through the OC. OCs with measured transmittance of 2.6%, 4.6%, 5.8%, and 7.1% were tested, and the best performance was obtained with the 4.6% OC. In cavity-dumping, the OC is replaced with an HR mirror. When the intracavity energy reaches its maximum, the PC is switched off, and the stored energy is dumped through the polarizer within one cavity round-trip. 3 Results and Discussion 3.1 Q-switching The results of the Q-switched laser operation are shown in Figure 2 . Figure 2: (a) Average power, (b) pulse energy, (c) peak power, and (d) pulse duration at repetition rate of 0.1, 1, and 10 kHz. The CW power is also plotted on (a). At a repetition rate of 10 kHz, the pulse energy was unstable at low pump power. Pulse energies exceeding 5 mJ were obtained at repetition rates of 1 kHz or lower. A clear rollover of the output pulse energy was observed near maximum pump level, which can be attributed to the non-stabilized pump spectrum, the elevated temperature (approximately 100 ∘ C according to thermal camera measurement) of the Ho:YAG thin-disk crystal and the RTP Pockels cell, and ETU process. The pulse duration decreased with increasing pump power due to the higher gain. The pulse duration remained longer than 292 ns, which limited the maximum peak power to 18.3 kW. To obtain shorter pulses, a higher net gain is required, which is inherently limited by the thin-disk geometry. Therefore, cavity-dumping is considered a more suitable approach for generating higher-peak-power pulses in thin-disk lasers. 3.2 Cavity-dumping The results of the cavity-dumped operation at different repetition rates, including the average power, pulse energy, peak power, and a representative temporal waveform, are shown in Figure 3 . Figure 3: (a) Average power, (b) pulse energy, and (c) peak power at different repetition rates. (d) Temporal waveform of a cavity-dumped pulse. The pulse duration was approximately 3.8 ns in all cases, corresponding to the round-trip time of the 114 cm optical cavity. The two-orders-of-magnitude shorter pulse duration compared with the Q-switched pulses enabled the generation of peak powers up to 1.6 MW. The beam quality, characterized by the M 2 factor, was evaluated by measuring the beam caustic using a 150 mm focal-length lens and a beam profiler. The measured M 2 values were approximately 1.7 in the horizontal

Read the complete text