Large-scale real-time signal processing in physics experiments: The ALICE TPC FPGA pipeline

S. Zhu · 2026

Read Large-scale real-time signal processing in physics experiments: The ALICE TPC FPGA pipeline by S. Zhu (2026) in the Tower of Babel, a free online library of public-domain works preserved in clean, searchable text. No sign-up. The full text is served as a plain-text file at a predictable URL, where text is present: https://antarctic-labs.com/tower-of-babel/arxiv-2601-15868.txt.

Introduction

S. Zhu describes real-time data handling for a major physics detector in a 2026 arXiv paper. The ALICE Time Projection Chamber was upgraded for LHC Run 3. It now runs in continuous readout mode. Lead-lead collisions arrive at rates up to 50 kilohertz. Those collisions produce over three terabytes of raw data per second. No storage system can simply keep that flood. Processing must happen in real time.

The paper details the FPGA pipeline that does this work. FPGAs are chips programmed for one fast, fixed task. The pipeline compresses and filters data as it streams. ALICE studies quark-gluon plasma in heavy-ion collisions. Its physics depends on catching rare events in the flood. A pipeline that keeps up at full rate is an engineering result in its own right.

Catalog record

CREATORS. Zhu
YEAR2026
COLLECTIONPAPERS
FORMATTXT
FILE SIZE7 KB
VERSION1.0
LICENSEhttp://creativecommons.org/licenses/by/4.0/
RIGHTSCC BY
SOURCEarXiv

Source: https://arxiv.org/abs/2601-15868

Browse the full library · About the Tower of Babel

Full text

The opening of the work, from the library's hosted text:

Large-scale real-time signal processing in physics experiments: The ALICE TPC FPGA pipeline
S. Zhu

Abstract
For LHC Run 3, the ALICE Time Projection Chamber (TPC) was upgraded to operate in continuous readout mode. Interaction rates of up to 50 kHz 50\text{\,}\mathrm{kHz} in Pb–Pb collisions require real-time processing of more than 3 TB s − 1 3\text{\,}\mathrm{TB}\text{\,}{\mathrm{s}}^{-1} of raw detector data. This requirement is met by a custom FPGA-based processing pipeline that performs the complete front-end data treatment fully in-stream, including common-mode correction, pedestal subtraction, ion-tail filtering, zero suppression, and dense data packing. A central element of the design is a highly parallel common-mode correction algorithm operating directly on the streaming data. It robustly identifies signal-free readout channels on a time-bin basis and applies pad-dependent scaling to compensate for local variations in capacitive coupling in the gas electron multiplier (GEM)readout. In combination with pedestal subtraction and ion-tail filtering, this enables accurate baseline restoration under extreme high-occupancy conditions, preventing signal loss while efficiently suppressing noise prior to zero suppression. The pipeline operates continuously at the full detector bandwidth and reduces the raw input rate of approximately 3 TB s − 1 3\text{\,}\mathrm{TB}\text{\,}{\mathrm{s}}^{-1} to about 900 GB s − 1 900\text{\,}\mathrm{GB}\text{\,}{\mathrm{s}}^{-1} for Pb–Pb collisions at the target interaction rate. Overall, it represents a large-scale FPGA-based real-time signal-processing implementation for high-energy physics detector readout.



1
The upgraded ALICE TPC

The
TPCof
A Large Ion Collider Experiment (ALICE), located at the CERN
Large Hadron Collider (LHC), served as the main tracking detector during Runs 1 and 2 (2009–2018), employing
multi-wire proportional chambers (MWPCs)with cathode-pad signal readout
[
TPCnim
]
.

To meet the demands of
LHCRuns 3 and 4, the
TPCunderwent a major upgrade during the
LHClong shutdown from 2019 to 2021.
The upgrade involved replacing the
MWPCswith new readout chambers based on
GEMtechnology and installing entirely new front-end electronics in order to continuously read the signals on the anode pads
[
TPCjinst
]
.
This modernization was driven by the need to accommodate much higher interaction rates, reaching up to
50\text{\,}\mathrm{kHz}
in lead–lead (
Pb–Pb
) collisions.

The
ALICE
TPCis a large cylindrical detector, divided longitudinally into two halves by a central drift electrode.
Each end plate, located at the ends of the cylinder, houses the readout chambers and is subdivided into 18 azimuthal sectors.
Every sector contains
Inner ReadOut Chambers (IROCs)and
Outer ReadOut Chambers (OROCs).
The new GEM-based readout chambers use a stack of four
GEMfoils for gas amplification.
Unlike the previous design, the upgraded system does not use an ion gating grid.
As a result, ion backflow—i.e., the return of positive ions into the drift volume—must be minimized.
This is achieved through a specially optimized amplification structure and a thoroughly tuned high-voltage configuration across the
GEMstack (cf.
[
TPCjinst
]
).

The upgraded
TPChas been successfully commissioned and is now fully operational, effectively supporting the physics objectives of
ALICEin high-luminosity heavy-ion collisions
[
ALICELOI
,
zitrone
]
.
In this publication, we describe in detail the readout system of the
ALICE
TPC, with a particular focus on the data processing algorithms implemented in firmware on the readout cards that receive data from the
TPCfront-end electronics.

1.1
Overview on the data processing chain

Figure 1
:
TPCdata processing chain.
The front-end electronics continuously transmit all sampled data off-detector.
In the First-Level Processors (FLP), each hosting two or three FPGA-based readout cards, known as Common Readout Units (CRUs), the data are corrected for specific detector effects and reduced in size.
The resulting reduced data stream is distributed to the Event-Processing Nodes (EPNs).
Each EPN performs online calibration, reconstruction, data reduction and data compression, before the data are directed to permanent storage.

The full data processing chain is illustrated schematically in Fig.
1
.
At the front-end electronics (cf. Section
1.2
), signals from the
524\,160
anode readout pads are amplified, shaped, and continuously sampled and digitized at a rate of
5\text{\,}\mathrm{MHz}
.
The digitized data are multiplexed into
6552
radiation-tolerant optical readout links.
At this stage, no data reduction is applied, ensuring that all raw detector information is available for subsequent correction of detector-specific effects at the next stage.
The total data rate from the
TPCamounts to
3.3\text{\,}\mathrm{TB}\text{\,}{\mathrm{s}}^{-1}
.
The data are received by a total of 360
Common Readout Units (CRUs)(cf. Section
), each containing a large
field-programmable gate array (FPGA), which is programmed to perform data processing and reduction tasks (cf. Section
).

The performance of the
GEM-based signal amplification is affected by two effects:
(i) baseline fluctuations induced by the
common-mode effect
, and
(ii) characteristic distortions in the pulse shape caused by slowly drifting ions in the induction gap (
ion tails
).
Both phenomena are described in detail in
[
CMCITpaper
]
and are corrected in the
CRU
FPGA.
Zero-suppression is applied only after these corrections, so that the data volume is effectively reduced without loss of information.

The
CRUsare installed in 144
First-Level Processors (FLPs), which are dedicated readout computers, each hosting two or three
CRUs, depending on data throughput.
Data are pushed from the
FLPsto the
Event-Processing Nodes (EPNs)farm via custom distribution software deployed on both farms.
For
Pb–Pb
collisions at
50\text{\,}\mathrm{kHz}
, the total data rate remains below
900\text{\,}\mathrm{GB}\text{\,}{\mathrm{s}}^{-1}
.

The continuous stream is segmented into
Time Frames (TFs)of configurable length (currently
2.85\text{\,}\mathrm{ms}
).
2
2

2

The time frames are sized to fit in the
graphics processing unit (GPU)memory for efficient processing on the
EPNs.

Each
FLPproduces
Sub-Time Frames (STFs)from a TPC subset.
While not all
EPNsreceive all
STFs, each one receives the complete set required to assemble a full
TF.

Since
TPCcalibration and compression require track information,
EPNsperform full online track reconstruction during data taking.
Each server is equipped with eight
GPUs, which handle tracking and calibration entirely.

The output stream to storage is about
130\text{\,}\mathrm{GB}\text{\,}{\mathrm{s}}^{-1}
for
Pb–Pb
at
50\text{\,}\mathrm{kHz}
.
Further asynchronous processing, on the
EPNsor on the
ALICEcomputing grid,
refines the data to final precision.

1.2
Front-end electronics

The
front-end card (FEC)for the
ALICE
TPCis described in detail in
[
TPCjinst
]
and illustrated schematically in Fig.
.

Read the complete text