Tritium accumulation and ozone decontamination of tungsten and beryllium

2025

Read Tritium accumulation and ozone decontamination of tungsten and beryllium (2025) in the Tower of Babel, a free online library of public-domain works preserved in clean, searchable text. No sign-up. The full text is served as a plain-text file at a predictable URL, where text is present: https://antarctic-labs.com/tower-of-babel/arxiv-2512-24256.txt.

Introduction

Dominic Batzler and five colleagues measure tritium sticking to fusion materials. Tritium adsorbs on surfaces and causes problems. Fusion plants and tritium laboratories both face them. How much accumulates depends on the material. Contaminated surfaces then need cleaning, preferably in place. Ozone under ultraviolet light is one candidate method.

A single setup at Tritium Laboratory Karlsruhe addresses both questions. Samples meet gaseous tritium while activity is tracked over time. The chamber can then fill with dry air, plain or ozonated. Beryllium and tungsten were the test materials. Both matter for fusion. Beryllium accumulated tritium over four times faster than tungsten. The cleaning tests brought a surprise. Ozone alone did no better than dry air. Ultraviolet light proved to be the required ingredient for real decontamination.

Catalog record

YEAR2025
COLLECTIONPAPERS
FORMATTXT
FILE SIZE13 KB
VERSION1.0
LICENSEhttp://creativecommons.org/licenses/by/4.0/
RIGHTSCC BY
SOURCEarXiv

Source: https://arxiv.org/abs/2512-24256

Browse the full library · About the Tower of Babel

Full text

The opening of the work, from the library's hosted text:

Tritium accumulation and ozone decontamination of tungsten and beryllium Abstract Tritium adsorption on surfaces creates a variety of issues, ranging from the fields of fusion applications to small and large-scale laboratory experiments using tritium. The extent to which tritium accumulates on surfaces is generally material-dependent and must be determined through experiments. Additionally, this surface contamination necessitates the implementation of appropriate decontamination procedures, preferably in-situ. A suitable method could be exposure to ozone during UV irradiation. However, it is currently not known if both components are necessary for the decontamination. At Tritium Laboratory Karlsruhe, both questions on contamination and decontamination can be addressed using a single experimental setup. With this, it is possible to expose solid samples to gaseous tritium to measure the temporal activity evolution. Furthermore, the system can be filled with dry air, and dry air containing ozone to explore their decontamination effect. Both measurement modes were applied to beryllium and tungsten samples, which were chosen for their relevance in fusion. The beryllium surface was observed to accumulate tritium more than four times faster than tungsten when exposed to gaseous tritium. Concerning the decontamination, without simultaneous UV irradiation, exposure to ozone did not have any distinct effect on the surface activity compared to simply using dry air. This leads to the conclusion that UV illumination of the surfaces is required to achieve a significant decontamination factor. \addAuthor \correspondingAuthor Dominic Batzlera \correspondingEmail [email protected] \addAuthor Robin Größlea \addAuthor Philipp Haaga \addAuthor Elizabeth Paineb \addAuthor Marco Rölliga \addAuthor Marie-Christine Schäfera \addAuthor Marius Schaufelbergera \addAuthor Kerstin Trosta \addAffiliation aTritium Laboratory Karlsruhe, Institute for Astroparticle Physics, Karlsruhe Institute of Technology, Hermann-von-Helmholtz-Platz 1, 76344 Eggenstein-Leopoldshafen, Germany \addAffiliation bDepartment of Applied Physics, Eindhoven University of Technology, 5612 AZ Eindhoven, The Netherlands \addKeyword Tritium \addKeyword Tritium Laboratory Karlsruhe \addKeyword Tungsten \addKeyword Beryllium \addKeyword Beta-induced X-ray Spectrometry \titlePage 1 Introduction Exposure to gaseous tritium often results in activity accumulation on the surface. Such contamination poses multiple challenges for a fusion fuel cycle, and tritium handling facilities in general. These include the loss of process gas, the accumulation of tritium inventory, the complication of tritium accountancy calculations, and the need for increased safety precautions during maintenance. In tritium monitoring systems, this undesired contamination results in a history-dependent, elevated background signal, which is often referred to as memory effect [ 10 ] . For neutrino mass experiments, such as the Karlsruhe Tritium Neutrino (KATRIN) experiment [ 1 , 2 ] , this creates a systematic effect that needs to be studied and accounted for. Therefore, suitable decontamination strategies, ideally in-situ, are required to mitigate the aforementioned issues. While traditional methods, such as bake-out, are somewhat successful at reducing the surface activity [ 4 ] , the high temperatures in this case could create additional problems such as increased tritium permeation. UV/ozone exposure presents itself as a promising candidate for in-situ decontamination, which was already proven effective on tritiated surfaces, with a decontamination factor of up to three order of magnitudes [ 7 , 3 ] . However, from literature it is not clear which component is responsible for the decontamination efficiency. Some reports suggest that ozone or oxygen radicals alone are sufficient [ 6 , 8 ] , others conclude that only the combination of ozone and simultaneous UV irradiation are effective [ 3 , 11 ] . In case only ozone were required, the in-situ decontamination would be less complicated to put into practice. To address these questions, the Tritium Activity Chamber Experiment (TRACE) was employed [ 4 ] . It is suited to expose solid samples both to gaseous tritium for contamination, and ozone (without UV irradiation) for decontamination. Both measurement modes were applied to tungsten and beryllium due to their significance for fusion. Beryllium is also of interest for use in the KATRIN experiment. In this work, the results on the surface activity evolution of tungsten and beryllium due to exposure to tritium, as well as the effect of ozone on their surface activity are reported. 2 Experimental Setup The TRACE system consists of a sample cell based on DN 40 CF components with optimised geometry to minimise tritium inventory. A gold-coated beryllium window serves as one of the interfaces and enables in-situ measurements of the sample’s surface activity by beta-induced X-ray spectrometry (BIXS) [ 9 ] . For A more detailed description of the experimental setup, see [ 4 ] . A UV-based ozone generator, similar to that used in [ 5 ] was connected to the measurement cell to expose the samples to ozone. Throughout the measurement campaigns, the purity of the tritium used for contamination was above 95%. 2.1 Sample preparation (a) (b) Figure 1 : SEM images of the beryllium (a) and tungsten (b) samples. In this study, three S-65 beryllium samples by Materion with a minimum beryllium content of 99.2% were used. These were left unpolished and were cleaned with ethanol prior to being installed in the measurement cell. A tungsten sample was cut from a rolled metal sheet with an elemental purity of over 99% according to X-ray fluorescence analyses. Unlike the beryllium samples, the tungsten sample was manually polished and cleaned in an ultrasonic bath. Figure 1 shows images of the beryllium and tungsten surfaces taken using a scanning electron microscope (SEM), which reveal their different topologies. Before the start of the measurement campaigns, the samples were baked out at 200°C until a combined leak and out-gassing rate of lower than 10^{-9} mbar \cdot l/s was achieved. 3 Results 3.1 Contamination Figure 2 : Increase of surface activity of three beryllium samples due to repeated exposure to gaseous tritium. The samples were exposed to gaseous tritium for 10 min, followed by an evacuation period to measure the remaining tritium on the samples’ surfaces in-situ using BIXS. By repeating this process, the temporal evolution of the samples’ surface activity can be measured. The exposure pressures were selected such that the tritium was in the free molecular flow regime in order to avoid effects from gas self-interaction. For two beryllium and a tungsten sample, a pressure of 10^{-3} mbar was chosen, while a third beryllium sample was exposed to 2\cdot 10^{-3} mbar of tritium. Given the system’s geometry, these pressures correspond to Knudsen numbers of 30 and 15, respectively. The time series of the beryllium surface activities are shown in Figure 2 . Both statistical and systematic uncertainties are included in the individual data points; the largest contribution stems from the uncertainty on the sample cell volume for the activity calibration. With each subsequent sample, less activity is accumulated, ranging from a slope of (10.06\pm 0.70) kBq/(cm 2 mbar \cdot s) to (2.28\pm 0.22) kBq/(cm 2 mbar \cdot s) for the first and third samples, respectively. Figure 3 : Surface activity evolution of the tungsten sample. With a slope of (0.488\pm 0.026) kBq/(cm 2 mbar \cdot s), the tungsten sample retains considerably less tritium on its surface than beryllium, as displayed in Figure 3 . Due to its higher nuclear charge of Z=74 compared to beryllium’s Z=4 , the uncertainties are also significantly lower. 3.2 Ozone decontamination After concluding the contamination measurements, the third beryllium and the tungsten samples were used to test the ozone decontamination method. To investigate the impact of

Read the complete text