High-Resolution 3D-Printed Plastic Scintillators with Tertiary Dye

P.A. Hausladen · 2025

Read High-Resolution 3D-Printed Plastic Scintillators with Tertiary Dye by P.A. Hausladen (2025) in the Tower of Babel, a free online library of public-domain works preserved in clean, searchable text. No sign-up. The full text is served as a plain-text file at a predictable URL, where text is present: https://antarctic-labs.com/tower-of-babel/arxiv-2512-23612.txt.

Introduction

Chandler Moore and seven co-authors report a recipe for 3D-printing plastic scintillators, materials that flash light when radiation passes through and so serve in radiation detectors. Vat polymerization printing can make shapes that machining cannot, but ordinary resin cures too deeply under ultraviolet light, blurring fine features.

Their formula adds coumarin 450 as a third dye, which limits how far the curing light penetrates. The dye barely changed the emission spectrum or light output, yet printed resolution improved dramatically: freestanding pillars were resolved below a millimeter. Fully supported structures reached features near a tenth of a millimeter on a desktop printer. All samples separated neutron from gamma events, and the best reached half the light output of a standard commercial scintillator. The work appeared in the Journal of Instrumentation.

Catalog record

CREATORP.A. Hausladen
YEAR2025
COLLECTIONPAPERS
FORMATTXT
FILE SIZE56 KB
VERSION1.0
LICENSEhttp://creativecommons.org/licenses/by/4.0/
RIGHTSCC BY
SOURCEarXiv

Source: https://arxiv.org/abs/2512-23612

Browse the full library · About the Tower of Babel

Full text

The opening of the work, from the library's hosted text:

High-Resolution 3D-Printed Plastic Scintillators with Tertiary Dye P.A. Hausladen Abstract Additive manufacturing offers efficient production of plastic scintillators with nontrivial geometries using vat polymerization, allowing fabrication of geometries which would be difficult or even impossible to produce using conventional subtractive manufacturing. This work presents a novel photocurable scintillator formula that includes coumarin 450 as a tertiary dye to enable high-resolution 3D printing via the manipulation of the 405 nm cure light. Bulk photocured and 3D printed (with and without tertiary dye) samples were compared through observational assessment and spectral response. All samples showed pulse shape discrimination between neutron and gamma events. Inclusion of the tertiary dye has minimal impact on emission spectrum and light output, but significant impact on print resolution as shown by comparison of printed high-complexity geometries and feature resolution test objects. With the use of a cure-limiting dye, unsupported features—such as freestanding pillars—were resolvable down to 0.7 mm. Even finer resolution at or below 0.1 mm was achieved in fully supported, integrated structures printed with off-the-shelf 405 nm desktop 3D printer. Scintillators demonstrated a light output up to 50 % of EJ-200 with a PSD figure of merit up to 1.35 at 0.9 – 1.1 MeVee. 1 Introduction Organic scintillators are commonly used for detecting broad ranges of ionizing radiation due to their low cost, ruggedness, and ease of manufacture in large geometries. Plastic organic scintillators have been in use since the early 1950s [ 24 ] and are made up of long, linked chains of hydrocarbon materials that make the plastic material robust and machinable. Most plastic scintillators use aromatic monomers like vinyltoluene or styrene as a base, serving both as the primary building block for the polymer matrix but also as the primary excitation point for incoming radiation [ 3 ] . Plastic scintillators are traditionally manufactured by thermal polymerization, in which a liquid monomer-based resin is heated over a period of days or weeks to incite polymerization. While possible with precise and expensive machining tools, making scintillators with non-standard geometries using this approach is often impractical or even impossible. The advent of additive manufacturing (AM), in particular using light-based photopolymerization, offers a new potential path for the manufacture of these radiation detectors at much faster timescales and with arbitrary geometry [ 16 , 7 ] . Scintillating materials printed at high resolution offer potential applications in microfluidics [ 12 ] , high energy physics [ 2 , 27 ] , and rare-event physics [ 13 ] . Current literature examples of AM plastics with high print resolution and good scintillation performance either rely on a copolymerization scheme that can cause nonuniformities and a change in opacity due to unreacted monomer [ 16 , 1 ] or use a non-standard 365 nm wavelength [ 7 ] . The present work presents a scintillator resin formulation that prints at 405 nm, relies on a non-aromatic oligomer base and cross-linkers, and has pulse shape discrimination (PSD) to distinguish between fast neutron and gamma events. Leveraging the advances of AM for plastic scintillators requires fast curing resins that make optically clear plastics: one approach is to use light-based polymerization. However, resins incorporating aromatic structures with less reactive photopolymerizable end groups often exhibit significantly reduced polymerization rates, leading to solidification times of multiple hours for even small volumes [ 18 , 11 , 9 ] . Therefore scintillator resins based on standard aromatic monomers [ 16 , 1 ] need significantly longer curing times and result in poorer resolution. Alternatively, nonaromatic methacrylate and acrylate compounds due to their electron-rich carbon–carbon double bond (C=C) in the \alpha,\beta -unsaturated ester structure are highly reactive to light in combination with a photoinitiator, leading to curing times on the order of tens of seconds for a thin layer [ 20 , 26 , 11 ] . However, because these compounds are not aromatic, they do not contribute to the scintillation process. Frandsen, et al. showed that plastics with nonaromatic monomers that cure within minutes can still produce good scintillation performance, albeit worse than fully aromatic materials, by directly exciting the primary fluor [ 11 ] . This performance is quantified by light output (LO) and the Figure-of-Merit (FoM) metric for PSD. Generally, organic scintillators contain multiple scintillating ingredients including the base monomer, a primary fluor which absorbs energy from the base via radiationless transfer before then emitting photons, and a secondary fluor or wavelength shifter which absorbs the primary fluor light and shifts it to longer wavelengths, normally to better match photodetector quantum efficiency. Common primary fluors or primary dyes for organic scintillators include polyphenyl hydrocarbons, oxazoles, and oxadiazole aryls. One of the most common primary fluors is 2,5-diphenyloxazole (PPO). This fluor was used in the seminal works of Brooks and Zaitseva, et al. that showed PSD capability in plastic scintillators by increasing PPO concentration to upwards of 15-30%, enabling increased triplet-triplet annihilation which drives delayed fluorescence [ 6 , 28 ] . In formulations with nonaromatic bases where the primary fluor is directly excited by ionization radiation, this component is one of the most important in determining the LO, PSD, and the overall quality of the scintillating properties. Typical secondary fluors include 1,4-bis(2-methylstyryl)benzene (bis-MSB) and POPOP, but Frandsen, et al. showed that bis-MSB absorbs enough of the 405 nm cure light to result in a short cure depth which limited photo bulk polymerization [ 11 ] . Instead, they used exalite 416 which has reduced absorbance at 405 nm. 2 Motivation The current process of additively manufacturing scintillators via photopolymerization suffers from a tradeoff between LO and curing speed. Work from Chandler et al. found it is possible to additively manufacture PSD-capable plastics using less-standard 365 nm wavelength light with layer curing times lower than 9 seconds [ 7 ] but resulted in a suppressed light yield of no more than 31% of a benchmark plastic scintillator EJ-200. Work that produced higher LO by utilizing aromatic compounds like vinyltoluene required slow co-polymerization techniques that requires over a minute per layer for curing and risks causing the scintillators to significantly opaque [ 16 , 1 ] , making use in AM pathways less viable. Furthermore, current AM of scintillators with standard cure wavelengths (e.g., 405 nm) [ 11 , 16 , 1 ] is more accurately described as a 2D+ technique. While it is possible to fabricate 3D geometries, the method is constrained by the need to prevent the projected curing region of each layer from extending too far beyond the foot-print of the previous layer. If this overlap occurs, excess resin between the target layer and build plate cures unintentionally, leading to a dramatic loss in both vertical and horizontal print resolution. This issue is particularly problematic for complex geometries—such as those with internal voids or expanding cross-sections along the build direction. The root of this issue lies in the long mean free path (MFP) of 405 nm light in typical scintillator resin formulations. As a result, light can penetrate deep into the resin vat, polymerizing regions well beyond the intended exposure plane. This compromises the fidelity of fine features and imposes a design constraint on printable geometries. One strategy to mitigate this involves tailoring the resin’s optical properties through the modification

Read the complete text