First results of a Monolithic Active Pixel Sensor with Internal Signal Gain Fully Integrated in a 180 nm CMOS Technology
T. Suligoj · 2025
Read First results of a Monolithic Active Pixel Sensor with Internal Signal Gain Fully Integrated in a 180 nm CMOS Technology by T. Suligoj (2025) in the Tower of Babel, a free online library of public-domain works preserved in clean, searchable text. No sign-up. The full text is served as a plain-text file at a predictable URL, where text is present: https://antarctic-labs.com/tower-of-babel/arxiv-2512-17824.txt.
Introduction
Heinz Pernegger and a CERN-led team report first results from CASSIA, a pixel sensor that amplifies its own signal inside each pixel. At CERN's upgraded collider, hundreds of collisions blur into one snapshot, and separating them needs detectors that stamp arrival times as well as positions. Building gain into the pixel itself boosts weak hits above the noise without separate amplifier layers.
The chip, made in a standard 180 nanometer imaging process, carries gain layers under its pixels. First tests map how different pixel designs multiply charge. Turn the voltage low and it runs in gentle proportional mode; turn it high and the same pixel fires in single-photon avalanche mode. One device, two personalities, aimed at the timing trackers future colliders demand.
Catalog record
| CREATOR | T. Suligoj |
|---|---|
| YEAR | 2025 |
| COLLECTION | PAPERS |
| FORMAT | TXT |
| FILE SIZE | 57 KB |
| VERSION | 1.0 |
| LICENSE | http://creativecommons.org/licenses/by/4.0/ |
| RIGHTS | CC BY |
| SOURCE | arXiv |
Source: https://arxiv.org/abs/2512-17824
Browse the full library · About the Tower of Babel
Full text
The opening of the work, from the library's hosted text:
First results of a Monolithic Active Pixel Sensor with Internal Signal Gain Fully Integrated in a 180 nm CMOS Technology T. Suligoj Abstract Dense tracking environments in experiments at CERN’s High-Luminosity LHC and future FCC experiments call for an increased use of timing information in addition to the position measurement of pixel detectors. This adds one dimension to the information available, and is essential for pile-up mitigation at high luminosity. The CASSIA sensor project ( C MOS A ctive S en S or with I nternal A mplification) focuses on the development of pixel matrices with internal charge multiplication based on monolithic CMOS sensor technologies suitable for application as charged particle tracking and timing detectors. CMOS sensors with in-pixel internal amplification would result in higher signal amplitudes having an improved signal-to-noise ratio, better time resolution and increased sensitivity, making them attractive for high-radiation environments. Their monolithic integration in small pixels reduces the input capacitance of a front-end amplifier and power dissipation making it suitable for fine-pitch low-power detectors. Fast signal rise time due to internal charge amplification improves the response time and timing resolution, all of which makes such a technology attractive for future 4D tracking applications in HEP experiments. This paper presents the first results of the CASSIA sensor, a novel MAPS which uses gain layers fully integrated in a 180nm imaging process to achieve internal signal amplification. In the first measurements presented here we demonstrate the gain behaviour of different pixel implant designs and show that the sensor can be operated with low gain proportional mode as LGAD sensor at lower voltages and as SPAD sensor at higher voltages . 1 Introduction Monolithic active pixel sensors (MAPS) for charged particle detection offer a compact structure that reduces material budget and decreases parasitic capacitances at the sensor output node, resulting in lower noise and power dissipation. They are also more cost-effective than hybrid detectors for large tracking systems, eliminating the need for separate sensor and readout chips as well as expensive bump-bonding interconnects. Most monolithic pixel detectors demonstrated to date utilize passive, predominantly pin-diode based sensors, where the charge signal generated by incident particles is amplified by an integrated front-end amplifier. In contrast, low-gain avalanche diodes (LGADs) [ 1 ] amplify the primary signal through avalanche multiplication within a p-n junction before electronic amplification, providing higher signal amplitudes for a given number of generated charge carriers. LGADs are currently implemented as separate chips from the signal-processing electronics, using specialized fabrication technologies optimized to obtain a uniformly distributed avalanche multiplication region. This design captures charge carriers generated at any position within the entire pixel area, providing a high fill factor [ 2 ] . LGAD devices are typically fabricated separately because they require specialized implant structures and high-resistivity substrates that differ from standard CMOS processes used for readout electronics. The CMOS Active Sensor with Internal Amplification (CASSIA) project addresses this technological incompatibility by exploring novel designs that integrate avalanche multiplication directly into a high-volume monolithic CMOS imaging process. This approach combines the benefits of monolithic pixel sensors with internal signal amplification in a single device. By amplifying the primary ionization signal inside the pixel, CASSIA sensors provide a larger current signal, which significantly improves performance compared to current state-of-the-art radiation-hard fine-pitch CMOS pixel sensors for high-energy physics (HEP) applications. The key advantages include: • Higher signal amplitudes that enable simplification of in-pixel electronics, contributing to lower power consumption, • Enhanced timing resolution in fine-pitch MAPS for future 4D tracking and time-tagging applications, • Improved signal-to-noise ratio for operation in high-radiation environments. The CASSIA sensor is designed to provide two distinct operation modes with internal charge multiplication. In low-gain avalanche diode (LGAD) mode, the sensor operates below the hard breakdown voltage with moderate gain (typically 10–100), providing low noise rates essential for many applications. Operation at or above the hard breakdown voltage enables Geiger mode operation as a single-photon avalanche diode (SPAD), offering the highest time resolution [ 3 ] . SPADs provide extremely high intrinsic gain that can eliminate the need for a front-end amplifier, further improving the signal-to-noise ratio. However, SPAD operation presents challenges: devices require quenching and reset circuits to operate above breakdown voltage [ 4 ] . Additionally, SPADs investigated for particle detection applications [ 5 ] exhibit limitations including higher dark count rates (DCR) when integrated in CMOS [ 6 ] and DCR degradation in high-radiation environments [ 7 ] . In the full CMOS integration pursued for CASSIA, the same process can fabricate monolithic sensors without gain, LGADs, and SPADs, sharing common circuit blocks for signal processing, pixel address generation, and matrix readout. The operation mode is selected by adjusting the reverse bias voltage applied to the sensor, which controls the avalanche multiplication rate. In this work, we explore the implementation of internal amplification in the depleted monolithic pixel sensor technology used for the MALTA sensor family, which has demonstrated state-of-the-art performance in particle detection applications [ 8 , 9 ] . MALTA sensors exhibit particle detection efficiencies of 98–99% after exposure to non-ionizing energy loss (NIEL) fluences of 3\times 10^{15} 1 MeV n {}_{\text{eq}} /cm 2 , with timing resolution at the nanosecond level. To maintain radiation hardness at even higher fluences and further improve timing performance, the primary goal of the CASSIA project is full integration into the existing 180 nm TowerSemiconductor imaging sensor technology used for MALTA fabrication. Critically, this integration requires no changes to process parameters and uses only layers already available in the standard fabrication sequence. This research aims to combine typical HEP pixel detector pitches (50–100 \mu m) with timing resolution sufficient to enable future 4D tracking applications (target: < 100 ps) [ 10 ] . This paper presents the first results from CASSIA, a novel MAPS that uses gain layers fully integrated in a 180 nm imaging process to achieve internal signal amplification. We demonstrate the gain behavior of different pixel implant designs and show that the sensor can be operated in low-gain proportional mode (LGAD) at lower voltages and as a SPAD at higher voltages. The paper is organized as follows: Section 2 describes the CASSIA sensor design and fabrication, Section 3 presents TCAD simulations of the field configuration and electrical characteristics, Section 4 and 5 details experimental measurements including electrical characterization, optical response, pulsed laser measurements, and dark count rates, and Section 6 summarizes our conclusions. 2 The CASSIA sensor design The CASSIA sensor is implemented in the 180 nm TowerSemiconductor imaging process modified for MALTA fabrication [ 8 , 11 , 12 , 13 ] . The sensitive region is a 30 \mu m thick, depleted p-type epitaxial layer on top of a p+ substrate, as shown in Figure 1 . The readout electronics are implemented within a deep p-well region, which is from here on referred to as the electronics p-well. The electronics p-well provides isolation between the CMOS transistor’s n-wells and the substrate. The collection electrode is made as a circular n + -implant with a radius of 20 \mu m , which is from here on referred to as the n + -electrode. The deep p-wells of the electronics p-well shield the pMOS transistor’s n-well region from collecting ionization electrons generated in